Embed Size (px)
DESCRIPTION
Current, Voltage & Frequency Switches, Transmitters & Transducers or AC & DC Circuits.
Citation preview
SF CATA OG L
705 Current Voltage Power & Frequency Transducers PAGE 1 OF 12
BI-DIRECTIONAL CURRENT TRANSDUCERSPROVIDE AN ISOLATED BI-POLAR OUTPUT DIRECTLY PROPORTIONAL TO THE INPUT CURRENT. THE OUTPUT SIGNAL TRACTS THE INPUT CURRENT WAVEFORM AND RECREATES ALMOST ANY AC, DC, TRANSIENT OR COMPLEX CURRENT COMBINATION.
Series No.
905B 909M4 926 929 943 944 947 948 9000 S273 S449 S630 S651 S661B S745 S764 S784
DC CURRENT TRANSDUCERS MONITOR DC CURRENT BY PROVIDING A MAGNETICALLY ISOLATED ANALOG OUTPUT THAT IS DIRECTLY PROPORTIONAL TO THE INPUT. LOW CURRENT RANGES ARE AVAILABLE FOR DIFFERENTIAL AND GROUND FAULT CURRENT MONITORING.
Series No.
903B 904B 913A 913B 920 921 936 950 952 DCT S218 S347 S444 S465 S619 S646 S728B S767 S770
DC CURRENT DETECTORS COMPARES THE DC INPUT TO A FIXED OR ADJUSTABLE CURRENT LIMIT. THE OUTPUT IS AN ISOLATED SWITCH OR RELAY THAT ACTIVATES AS REQUIRED. DC CURRENT DETECTORS ARE SUITED FOR GROUND FAULT CURRENT MONITORING.
Series No.
901B S58 S201 S204 S623 S629 S680 S754
AC CURRENT TRANSDUCERS MAINTAIN ISOLATION AND PROVIDE AN ANALOG DC OUTPUT DIRECTLY PROPORTIONAL TO AC INPUT CURRENT. TRUE-RMS AND AVERAGE RESPONDING PRODUCTS ARE AVAILABLE IN CLAMP-ON AND PASS-THRU CONFIGURATIONS.
Series No.
1001 1002M1 1003AM1 1003AM2 1004 1005 1006 1006X 1055 1055L 1070 ACT ACTS C CX S383 S383L S402 S461 S714 S786
AC CURRENT DETECTORS COMPARES THE AC INPUT TO A FIXED OR ADJUSTABLE CURRENT LIMIT. THE OUTPUT IS AN ISOLATED SWITCH OR RELAY THAT IS ACTIVATED AS REQUIRED. PRODUCTS AVAILABLE IN CLAMP-ON AND PASS-THRU CONFIGURATIONS.
Series No.
870 871 880B 881 882 ACS ACS-3 ACS-SC S212
AC VOLTAGE TRANSDUCERS PRODUCE AN ISOLATED ANALOG OUTPUT SIGNAL DIRECTLY PROPORTIONAL TO AC VOLTAGE AT A VARIETY OF FREQUENCIES. HIGH SENSITIVITY VERSIONS ARE AVAILABLE WITH ZERO SUPPRESSED AC INPUT VOLTAGE RANGES.
Series No.
101M3 102M3 105 108 108X V VX S190
DC VOLTAGE TRANSDUCER & DETECTOR SERIES S657 PRODUCES AN ISOLATED ANALOG OUTPUT PROPORTIONAL TO DC VOLTAGE. SERIES S631 COMPARES THE DC INPUT TO AN ADJUSTABLE THRESHOLD. THE OUTPUT IS AN ISOLATED RELAY THAT ACTIVATES AS REQUIRED.
Series No.
S631 S657
AC POWER TRANSDUCERS PROVIDES AN ISOLATED ANALOG DC OUTPUT DIRECTLY PROPORTIONAL TO AC INPUT POWER. TRUE POWER (WATTS) AND VOLT-AMP-REACTIVE (VAR) TRANSDUCERS ARE AVAILABLE FOR A VARIETY OF POWER RANGES AND FREQUENCIES.
Series No.
415A 416A S73 S217 W&Q
FREQUENCY TRANSDUCERS PROVIDES AN ISOLATED ANALOG DC OUTPUT SIGNAL DIRECTLY PROPORTIONAL TO AC INPUT FREQUENCY. MANY RANGES ARE AVAILABLE, STARTING AT 5 TO 100HZ AND ALL THE WAY UP TO 1K TO 20KHZ.
Series No.
S343 S350L
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
For other products including modified standard & custom specials
Visit http://www.veederline.com.auemail [email protected]
or call toll-free +61 8 8347 3711
Thank you.
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
BI-DIRECTIONAL CURRENT TRANSDUCERS SEVENTEEN MODELS IN ORDER OF CURRENT RANGE
PAGE 2 OF12
SERIES 905B
Data Sheet
MIL GRADE; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER ±15VDC; TEMPERATURE –55° TO +85°C; APERTURE 3/8 INCH DIA; RESPONSE 50m-SEC; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS.
CURRENT RANGES 0 TO ±50MA 0 TO ±1A 0 TO ±100MA 0 TO ±2A 0 TO ±200MA 0 TO ±5A 0 TO ±500MA
SERIES S661B
Data Sheet
MIL GRADE; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER ±15VDC; TEMPERATURE –40° TO +85°C; APERTURE 3/4 INCH DIA; FREQUENCY DC TO 60HZ; RESPONSE 1m-SEC; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
CURRENT RANGES 0 TO ±100MA 0 TO ±400MA 0 TO ±200MA 0 TO ±500MA 0 TO ±250MA 0 TO ±750MA 0 TO ±300MA 0 TO ±1A
SERIES 926
Data Sheet
MIL GRADE: OUTPUT 0 TO ±5V; ACCURACY 0.25%FS; POWER +24 TO 32VDC; TEMPERATURE –55° TO +85°C; APERTURE 3/8 INCH DIA; RESPONSE 5m-SEC; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
CURRENT RANGES 0 TO ±5A 0 TO ±20A 0 TO ±10A 0 TO ±25A 0 TO ±15A
SERIES S764
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER +12 TO 36VDC; TEMPERATURE –40° TO +85°C; APERTURE 3/4 INCH DIA; RESPONSE 1m-SEC; PLASTIC CASE; BARRIER SCREW TERMINATIONS
CURRENT RANGES 0 TO ±20A 0 TO ±50A 0 TO ±25A 0 TO ±60A 0 TO ±30A 0 TO ±70A 0 TO ±40A 0 TO ±100A
SERIES S273
Data Sheet
MIL GRADE; OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±15VDC; FREQUENCY DC-100KHZ; RESPONSE 1µ-SEC; TEMPERATURE –55° TO +85°C; APERTURE 3/4 INCH DIA; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
CURRENT RANGES 0 TO ±25A 0 TO ±200A 0 TO ±50A 0 TO ±250A 0 TO ±100A 0 TO ±300A 0 TO ±150A 0 TO ±350A
SERIES S449
Data Sheet
SPACE FLIGHT; OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±15VDC; FREQUENCY DC-100KHZ; RESPONSE 1µ-SEC; TEMPERATURE –40° TO +71°C; APERTURE 1/4 INCH DIA; SOLDER HEADER TERMINATIONS
CURRENT RANGES 0 TO ±25A 0 TO ±50A 0 TO ±40A 0 TO ±60A
SERIES S745
Data Sheet
SPACE FLIGHT; OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±12VDC; FREQUENCY DC-20KHZ; RESPONSE 1-2µ-SEC; TEMPERATURE –55° TO +100°C; APERTURE 3/8 INCH DIA; METAL CASE; WEIGHT 8OZ.; SOLDER HEADER TERMINATIONS
CURRENT RANGES 0 TO ±40A 0 TO ±150A 0 TO ±75A 0 TO ±250A
SERIES 929
Data Sheet
MIL GRADE; OUTPUT 0 TO ±5V; ACCURACY 1%FS (OVER TEMPERATURE); POWER +10VDC TO +34VDC; FREQUENCY DC-350KHZ; RESPONSE 1µ-SEC; TEMPERATURE –40° TO +85°C; APERTURE 3/4 INCH DIA; CONNECTOR OR BARRIER TERMINATIONS
CURRENT RANGES 0 TO ±50A 0 TO ±200A 0 TO ±75A 0 TO ±250A 0 TO ±100A 0 TO ±300A 0 TO ±150A 0 TO ±400A
SERIES S651
Data Sheet
MIL GRADE; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER +22 TO +32VDC; FREQUENCY DC-3.5KHZ; RESPONSE 100µ-SEC; TEMPERATURE –40° TO +65°C; APERTURE 1+3/8 INCH DIA; CONNECTOR TERMINATIONS
CURRENT RANGES 0 TO ±100A 0 TO ±200A
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
BI-DIRECTIONAL CURRENT TRANSDUCERS CONTINUED (PART TWO OF TWO)
PAGE 3 of 12
SERIES S784
Data Sheet
AIRCRAFT DO-160; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER +16 TO 40VDC; FREQUENCY DC-1KHZ; RESPONSE 500µ-SEC; TEMPERATURE –40° TO +85°C; APERTURE 3/4 INCH DIA; METAL CASE; WEIGHT 9OZ.; SOLDER HEADER TERMINATIONS
CURRENT RANGES 0 TO ±100A 0 TO ±400A 0 TO ±200A 0 TO ±500A 0 TO ±250A 0 TO ±600A 0 TO ±300A 0 TO ±750A
SERIES 947
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±15VDC; FREQUENCY DC-100KHZ; RESPONSE 1µ-SEC; TEMPERATURE –20° TO +70°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
CURRENT RANGES 0 TO ±100A 0 TO ±400A 0 TO ±200A 0 TO ±500A 0 TO ±300A 0 TO ±600A
SERIES 943A Data Sheet
MIL GRADE; OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±15VDC; FREQUENCY DC-100KHZ; RESPONSE 1µ-SEC; TEMPERATURE –55° TO +85°C; APERTURE 1+3/8 INCH DIA; METAL CASE; BARRIER OR CONNECTOR TERMINATIONS
CURRENT RANGES 0 TO ±100A 0 TO ±600A 0 TO ±200A 0 TO ±750A 0 TO ±300A 0 TO ±800A 0 TO ±400A 0 TO ±1000A 0 TO ±500A
SERIES 944
Data Sheet
MIL GRADE: OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±15VDC; FREQUENCY DC-20KHZ; TEMPERATURE –55° TO +85°C; APERTURE 1+3/8 INCH DIA; METAL CASE; BARRIER SCREW OR CONNECTOR TERMINATIONS
CURRENT RANGES 0 TO ±600A 0 TO ±1500A 0 TO ±800A 0 TO ±2000A 0 TO ±1000A
SERIES 948
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO ±5V; ACCURACY 0.5%FS; POWER ±15VDC; FREQUENCY DC-20KHZ; TEMPERATURE –20° TO +70°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
CURRENT RANGES 0 TO ±600A 0 TO ±1500A 0 TO ±800A 0 TO ±2000A 0 TO ±1000A
SERIES 909M4
Data Sheet
CLAMP-ON; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER ±15VDC; RESPONSE 200µ-SEC; TEMPERATURE –25° TO +75°C; APERTURE 1+1/2 INCH DIA; METAL CASE; BARRIER SCREW OR CONNECTOR TERMINATIONS
CURRENT RANGES 0 TO ±150A 0 TO ±1000A 0 TO ±250A 0 TO ±1500A 0 TO ±500A 0 TO ±2000A 0 TO ±750A 0 TO ±2500A
SERIES 9000
Data Sheet
CLAMP-ON; OUTPUT 0 TO ±5V; ACCURACY 1%FS; POWER ±15VDC; RESPONSE 200µ-SEC; TEMPERATURE –25° TO +75°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW OR CONNECTOR TERMINATIONS
CURRENT RANGES 0 TO ±150A 0 TO ±1000A 0 TO ±250A 0 TO ±1500A 0 TO ±500A 0 TO ±2000A 0 TO ±750A 0 TO ±2500A
SERIES S630
Data Sheet
RAIL TRANSIT; OUTPUT 0 TO ±250MA; ACCURACY 0.5%FS; POWER +24VDC; RESPONSE 1M-SEC; TEMPERATURE –25° TO +75°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BUS-BAR AVAILABLE; BARRIER SCREW TERMINATIONS
CURRENT RANGE 0 TO ±1000A OUTPUT TO INPUT RATIO: ±250µA PER AMP
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
DC CURRENT TRANSDUCERS NINETEEN MODELS IN ORDER OF CURRENT RANGE
PAGE 4 of 12
SERIES 904B
Data Sheet
MIL GRADE; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; TEMPERATURE –55° TO +85°C; INPUT VIA IN-LINE CONNECTION; RESPONSE 50m-SEC; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +100µA 0 TO +1MA 0 TO +200µA 0 TO +2MA 0 TO +500µA 0 TO +5MA
SERIES 903B
Data Sheet
MIL GRADE; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 50m-SEC; TEMPERATURE –55° TO +85°C; APERTURE 3/8 INCH DIA; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +5MA 0 TO +100MA 0 TO +1A 0 TO +10MA 0 TO +200MA 0 TO +2A 0 TO +20MA 0 TO +500MA 0 TO +5A 0 TO +50MA
SERIES S767
Data Sheet
SPACE FLIGHT; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +22 TO 36VDC; RESPONSE 50m-SEC; TEMPERATURE –40° TO +85°C; APERTURE 1/2 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +10MA 0 TO +200MA 0 TO +20MA 0 TO +250MA 0 TO +50MA 0 TO +500MA 0 TO +100MA 0 TO +1A
SERIES 936
Data Sheet
HV GROUND FAULT; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 100m-SEC; TEMPERATURE –55° TO +85°C; APERTURE 3/4 INCH DIA; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +10MA 0 TO +200MA 0 TO +1A 0 TO +20MA 0 TO +250MA 0 TO +2A 0 TO +50MA 0 TO +500MA 0 TO +5A 0 TO +100MA
SERIES S218
Data Sheet
GROUND FAULT OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 50m-SEC; TEMPERATURE –55° TO +85°C; APERTURE 1+1/4 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +100MA 0 TO +1A 0 TO +200MA 0 TO +2A 0 TO +500MA 0 TO +5A
SERIES S619
Data Sheet
SPACE FLIGHT; OUTPUT 0 TO +3.5V (ISOLATED); ACCURACY 2%FS; POWER +4.5 TO +5.5VDC; INPUT CURRENT BY IN-LINE CONNECTION; RESPONSE 1m-SEC; TEMPERATURE –55° TO +85°C; PCB MOUNT; SOLDER TERMINATIONS
DC CURRENT RANGES 0 TO +3.5A 0 TO +10A
SERIES 950
Data Sheet
MIL GRADE; OUTPUT 0 TO +5V; ACCURACY 0.5%FS; POWER +24 TO 32VDC; RESPONSE 10m-SEC; TEMPERATURE –25° TO +85°C; APERTURE 3/8 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +10A 0 TO +40A 0 TO +20A 0 TO +50A 0 TO +30A
SERIES 913B
Data Sheet
MIL GRADE; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 1m-SEC; TEMPERATURE –55° TO +85°C; APERTURE 3/4 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +10A 0 TO +30A 0 TO +50A 0 TO +15A 0 TO +35A 0 TO +75A 0 TO +20A 0 TO +40A 0 TO +100A 0 TO +25A
SERIES 913A
Data Sheet
MIL GRADE; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 1m-SEC; TEMPERATURE –55° TO +85°C; APERTURE 3/8 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +10A 0 TO +40A 0 TO +20A 0 TO +50A 0 TO +25A 0 TO +75A 0 TO +30A 0 TO +100A
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
DC CURRENT TRANSDUCERS CONTINUED (PART TWO OF TWO)
PAGE 5 of 12
SERIES S770
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +12 TO 36VDC; RESPONSE 1m-SEC; TEMPERATURE –40° TO +85°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; CHASSIS MOUNT; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 TO +20A 0 TO +60A 0 TO +25A 0 TO +70A 0 TO +30A 0 TO +100A 0 TO + 50A
SERIES 920
Data Sheet
CLAMP-ON; OUTPUT 4 TO +20mADC; ACCURACY 1%FS; LOOP POWER +18 TO 28VDC; RESPONSE 10m-SEC; TEMPERATURE –40° TO +85°C; APERTURE 1.60 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 TO +50A 0 TO +100A 0 TO +75A 0 TO +125A
SERIES DCT
Data Sheet
CLAMP-ON; OUTPUT 0 TO +5V OR 4 TO 20MA; ACCURACY 1%FS; POWER +20 TO 50VDC OR 22 TO 38VAC; RESPONSE 100m-SEC; OPENING 0.85 X 0.85 INCH; TEMPERATURE –20° TO +50°C; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES -100: 0 TO +50A, 75A OR 100A -200: 0 TO +100A, 150A OR 200A -300: 0 TO +150A, 225A OR 300A -400: 0 TO +200A, 300A OR 400A
SERIES S728B
Data Sheet
SPACE FLIGHT; OUTPUT 0 TO +5V; ACCURACY 0.3% TO 0.5%FS; POWER +24 TO 32VDC; RESPONSE 1µ-SEC; TEMPERATURE –55° TO +85°C; APERTURE 1/2 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER HEADER TERMINATIONS
DC CURRENT RANGES 0 TO +50A 0 TO +250A 0 TO +100A 0 TO +300A 0 TO +150A 0 TO +400A 0 TO +200A
SERIES 952
Data Sheet
MIL GRADE; OUTPUT 0 TO +5V; ACCURACY 0.3% TO 0.5%FS; POWER +24 TO 32VDC; RESPONSE 1µ-SEC; TEMPERATURE –55° TO +85°C; APERTURE 3/4 INCH DIA; METAL CASE; CHASSIS MOUNT; SOLDER HEADER TERMINATIONS
DC CURRENT RANGES 0 TO +50A 0 TO +250A 0 TO +500A 0 TO +100A 0 TO +300A 0 TO +600A 0 TO +150A 0 TO +400A 0 TO +750A 0 TO +200A
SERIES S347
Data Sheet
CLAMP-ON; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 200µ-SEC; TEMPERATURE –25° TO +75°C; APERTURE 1+1/2 INCH DIA; METAL CASE; BARRIER SCREW OR CONNECTOR TERMINATIONS
DC CURRENT RANGES 0 TO +100A 0 TO +300A 0 TO +1500A 0 TO +150A 0 TO +500A 0 TO +2000A 0 TO +200A 0 TO +750A 0 TO +2500A 0 TO +250A 0 TO +1000A 0 TO +5000A
SERIES 921
Data Sheet
CLAMP-ON; OUTPUT 4 TO +20mADC; ACCURACY 1%FS; LOOP POWER +18 TO 28VDC; RESPONSE 10m-SEC; TEMPERATURE –40° TO +85°C; APERTURE 1.60 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 TO +200A 0 TO +400A 0 TO +1000A 0 TO +250A 0 TO +500A 0 TO +1500A 0 TO +300A 0 TO +750A 0 TO +2000A
SERIES S444
Data Sheet
CLAMP-ON; OUTPUT 0 TO +5V; ACCURACY 1%FS; POWER +24 TO 32VDC; RESPONSE 200µ-SEC; TEMPERATURE –25° TO +75°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW OR CONNECTOR TERMINATIONS
DC CURRENT RANGES 0 TO +200A 0 TO +500A 0 TO +1500A 0 TO +225A 0 TO +750A 0 TO +2000A 0 TO +250A 0 TO +1000A 0 TO +2500A 0 TO +300A
SERIES S465
Data Sheet
RAIL TRANSIT CLAMP-ON; OUTPUT 4 TO 20MA; ACCURACY 1%FS; POWER +16 TO 26VDC; RESPONSE 200µ-SEC; TEMPERATURE –25° TO +75°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW OR CONNECTOR TERMINATIONS
DC CURRENT RANGES 0 TO +150A 0 TO +1000A 0 TO +250A 0 TO +1500A 0 TO +500A 0 TO +2000A 0 TO +750A 0 TO +2500A
SERIES S646
Data Sheet
RAIL TRANSIT CLAMP-ON; OUTPUT 0 TO +6V; ACCURACY 2%FS; POWER +15VDC; RESPONSE 200µ-SEC; TEMPERATURE –30° TO +60°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 TO +1000A
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
DC CURRENT DETECTORS EIGHT MODELS IN ORDER OF CURRENT RANGE
PAGE 6 of 12
SERIES 901B
Data Sheet
GROUND FAULT; OUTPUT SOLID-STATE-SWITCH AND 0 TO 5VDC; ACCURACY 1%FS; POWER +21 TO +27VDC; RESPONSE 50M-SEC; TEMPERATURE –20° TO +70°C; APERTURE 3/4 INCH DIA; METAL CASE; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +20MA 0 TO +500MA 0 TO +50MA 0 TO +1A 0 TO +100MA 0 TO +2A 0 TO + 250MA 0 TO +5A
SERIES S204
Data Sheet
INDUSTRIAL GRADE; OUTPUT SPDT RELAY; ACCURACY 4% OF SET POINT; POWER +22.8 TO +30.4VDC; RESPONSE 3M-SEC; TEMP. –20° TO +70°C; APERTURE 3/8 INCH DIA; METAL CASE; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
DC CURRENT RANGES 0 TO +100MA 0 TO +1.2A 0 TO +150MA 0 TO +2A 0 TO +350MA 0 TO +3A 0 TO +550MA 0 TO +5.75A
SERIES S58
Data Sheet
INDUSTRIAL GRADE; OUTPUT SOLID-STATE-SWITCH; AUTOMATIC RESET; POWER +22.8 TO +30.4VDC; RESPONSE 1M-SEC; TEMPERATURE 0° TO +70°C; APERTURE 3/8 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 TO +15ADC
SWITCH TRIPS @ 60MADC ±20%
SERIES S754
Data Sheet
RAIL TRANSIT; OUTPUT SOLID-STATE-RELAY; PUSHBUTTON RESET; RESPONSE 100M-SEC; POWER +25 TO +45VDC; TEMPERATURE -40° TO +50°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 TO +20ADC
ADJUSTABLE TRIP CURRENT
500MA TO 1ADC
SERIES S201
Data Sheet
AIRCRAFT DO-160; OUTPUT SPST RELAY; AUTOMATIC RESET; POWER +24 TO +32VDC; RESPONSE 200M-SEC; TEMP. –55° TO +70°C; APERTURE 3/8 INCH DIA; METAL CASE; CONNECTOR TERMINATIONS; DO-160 ENVIRONMENTAL REQUIREMENTS
DC CURRENT RANGES 0 TO +100ADC
RELAY TRIPS@ +1ADC ±15%
SERIES S680
Data Sheet
RAIL TRANSIT; OUTPUT SOLID-STATE-RELAY; AUTOMATIC RESET; POWER +25 TO +45VDC; RESPONSE 1M-SEC; TEMPERATURE -25° TO +75°C; APERTURE 1+1/2 INCH DIA; AVAILABLE WITH BUS-BAR; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 to +1000Adc
RELAY TRIPS@ ±3Adc ±10%
SERIES S629
Data Sheet
RAIL TRANSIT; OUTPUT SPST RELAY (10A CONTACTS); AUTOMATIC RESET; RESPONSE 50M-SEC; TEMP –25° TO +75°C; POWER +25 TO +45VDC; APERTURE 1+1/2 INCH DIA; BUS-BAR AVAILABLE; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 to +1000Adc
RELAY TRIPS@
±45Adc ±0.5Adc
SERIES S623
Data Sheet
RAIL TRANSIT GROUND FAULT; OUTPUT SPST RELAY; AUTOMATIC RESET; RESPONSE 50M-SEC; POWER +25 TO +45VDC; TEMP –25° TO +75°C; APERTURE 1+1/2 INCH DIA; DUAL BUS-BAR AVAILABLE; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC CURRENT RANGES 0 to +1600Adc
RELAY TRIP
ADJUSTMENT RANGE:
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
AC CURRENT TRANSDUCERS TWENTY-ONE MODELS IN ORDER OF CURRENT RANGE
PAGE 7 OF 12
SERIES 1055L
Data Sheet
INDUSTRIAL GRADE; OUTPUT 4 TO 20mA; ACCURACY 0.5%FS; TWO WIRE LOOP POWER +7 TO +35VDC; FREQUENCY 50-60HZ; RESPONSE 100m-SEC; TEMP. –20° TO +85°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 50MA 0 TO 250MA 0 TO 100MA 0 TO 500MA 0 TO 200MA 0 TO 1A
SERIES S383L
Data Sheet
PROCESS CONTROL; OUTPUT 4 TO 20mA; ACCURACY 0.5%FS; TWO WIRE LOOP POWER +7 TO +35VDC; FREQUENCY 50-60HZ; RESPONSE 100m-SEC; TEMP. –40° TO +85°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 50MA 0 TO 250MA 0 TO 100MA 0 TO 500MA 0 TO 200MA 0 TO 1A
SERIES 1002M1
Data Sheet
MIL GRADE; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; POWER +24 TO +32VDC; FREQUENCY 375-475HZ (OTHERS AVAILABLE); RESPONSE 10m-SEC; TEMPERATURE -55° TO +85°C; APERTURE 3/4 INCH DIA; SOLDER, CONNECTOR OR BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 250MA 0 TO 20A 0 TO 100A 0 TO 500MA 0 TO 25A 0 TO 150A 0 TO 1A 0 TO 50A 0 TO 200A 0 TO 5A 0 TO 65A 0 TO 250A 0 TO 10A
SERIES S402
Data Sheet
RMS RESPONDING; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; POWER +24 TO +32VDC; FREQUENCY 57-63HZ (OTHERS AVAILABLE); RESPONSE 100m-SEC; TEMPERATURE 0° TO 70°C; APERTURE 3/4 INCH DIA; METAL CASE; SOLDER, CONNECTOR OR BARRIER TERMINALS
AC CURRENT RANGES 0 TO 250MA 0 TO 5A 0 TO 100A 0 TO 500MA 0 TO 10A 0 TO 150A 0 TO 1A 0 TO 20A 0 TO 200A 0 TO 2A 0 TO 50A 0 TO 250A 0 TO 3A
SERIES C
Data Sheet
AVERAGE RESPONDING; OUTPUT 0 TO 1mADC; ACCURACY 0.25%FS; POWERED BY INPUT; FREQUENCY 47-1000HZ; RESPONSE 400m-SEC; TEMPERATURE -20° TO +70°C; INPUT BY IN-LINE CONNECTION; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 1A 0 TO 10A 0 TO 2A 0 TO 20A 0 TO 5A
SERIES CX
Data Sheet
AVERAGE RESPONDING; OUTPUT 4 TO 20MADC; ACCURACY 0.25%FS; LOOP-POWER 10 TO 35VDC; FREQUENCY 47-1000HZ; RESPONSE 400M-SEC; TEMPERATURE -20° TO +70°C; INPUT BY IN-LINE CONNECTION; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 1A 0 TO 10A 0 TO 2A 0 TO 20A 0 TO 5A
SERIES 1003AM1
Data Sheet
PROCESS OUTPUT 0 TO 5VDC; ACCURACY 1%FS; FREQUENCY 57-63HZ (OTHERS AVAILABLE); POWERED BY INPUT; RESPONSE 150m -SEC; TEMPERATURE -20° TO +70°C; APERTURE 3/8 INCH DIA; METAL CASE; BARRIER TERMINALS
AC CURRENT RANGES 0 TO 2A 0 TO 20A 0 TO 50A 0 TO 5A 0 TO 25A 0 TO 60A 0 TO 7A 0 TO 30A 0 TO 75A 0 TO 10A 0 TO 40A 0 TO 100A 0 TO 15A
SERIES 1004
Data Sheet
MIL GRADE; OUTPUT 0 TO 5VDC; ACCURACY 1%FS; FREQUENCY 375 TO 475HZ; RESPONSE 150m-SEC; TEMPERATURE -55° TO +85°C; POWERED BY INPUT; APERTURE 3/8 OR 3/4 INCH DIA; METAL CASE; SOLDER, CONNECTOR OR BARRIER TERMINATIONS
AC CURRENT RANGES 0 TO 2A 0 TO 50A 0 TO 250A 0 TO 5A 0 TO 100A 0 TO 300A 0 TO 10A 0 TO 150A 0 TO 350A 0 TO 20A 0 TO 200A 0 TO 400A
SERIES 1005
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO 5VDC; ACCURACY 1-2%FS; FREQUENCY 50 TO 60HZ; RESPONSE 80m-SEC; TEMPERATURE -20° TO +70°C; POWERED BY INPUT; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 2A 0 TO 30A 0 TO 150A 0 TO 5A 0 TO 50A 0 TO 200A 0 TO 10A 0 TO 75A 0 TO 250A 0 TO 20A 0 TO 100A 0 TO 300A
SERIES 1055
Data Sheet
INDUSTRIAL GRADE; OUTPUT 4 TO 20mA; ACCURACY 0.5%FS; TWO WIRE LOOP POWER +7 TO +35VDC; FREQUENCY 50-60HZ; RESPONSE 100m-SEC; TEMPERATURE –20° TO +85°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 2A 0 TO 30A 0 TO 100A 0 TO 5A 0 TO 40A 0 TO 150A 0 TO 10A 0 TO 50A 0 TO 200A 0 TO 20A 0 TO 75A 0 TO 250A 0 TO 25A
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
AC CURRENT TRANSDUCERS CONTINUED (PART TWO OF THREE)
PAGE 8 OF 12
SERIES S383
Data Sheet
PROCESS CONTROL; OUTPUT 4 TO 20mA; ACCURACY 0.5%FS; TWO WIRE LOOP POWER +7 TO +35VDC; FREQUENCY 50-60HZ; RESPONSE 100m-SEC; TEMPERATURE –40° TO +85°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 2A 0 TO 30A 0 TO 100A 0 TO 5A 0 TO 40A 0 TO 150A 0 TO 10A 0 TO 50A 0 TO 200A 0 TO 20A 0 TO 75A 0 TO 250A
SERIES 1070
Data Sheet
AC RMS; OUTPUT 4 TO 20mA; ACCURACY 0.25%FS; TWO WIRE LOOP POWER +12 TO +32VDC; FREQUENCY 20-2KHZ; RESPONSE 300m-SEC; TEMP –40° TO +85°C; APERTURE 3/4 INCH; PLASTIC CASE; BARRIER SCREW, CONNECTOR OR SUB-D TERMINATIONS
AC CURRENT RANGES 0 TO 2A 0 TO 20A 0 TO 50A 0 TO 200A 0 TO 5A 0 TO 25A 0 TO 75A 0 TO 250A 0 TO 10A 0 TO 30A 0 TO 100A 0 TO 15A 0 TO 40A 0 TO 150A
SERIES ACTS
Data Sheet
AC RMS CLAMP-ON; OUTPUT 4 TO 20mA; ACCURACY 0.8%FS; LOOP POWER +24 TO +40VDC; FREQUENCY 10-400HZ; RESPONSE 600m-SEC; TEMPERATURE –20° TO +50°C; OPENING 0.85 X 0.85 INCH; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES -05: 0 TO 2A, OR 5A -50: 0 TO 10A, 20A OR 50A -200: 0 TO 100A, 150A OR 200A
SERIES ACT
Data Sheet
AC-AVG RESPONDING CLAMP-ON; OUTPUT 0 TO 5VDC, 0 TO 10VDC OR 4 TO 20mA; ACCURACY 0.5% OR 1%FS; SELF OR LOOP POWER; FREQUENCY 50-60HZ OR 20-100HZ; TEMPERATURE –20° TO +50°C; OPENING 0.85 X 0.85 INCH; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES -05: 0 TO 2A, OR 5A -50: 0 TO 10A, 20A OR 50A -200: 0 TO 100A, 150A OR 200A
SERIES 1006
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; FREQUENCY 50 TO 60HZ; RESPONSE 130m-SEC; TEMPERATURE -20° TO +70°C; POWERED BY INPUT; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 5A 0 TO 75A 0 TO 500A 0 TO 10A 0 TO 100A 0 TO 600A 0 TO 25A 0 TO 150A 0 TO 800A 0 TO 30A 0 TO 250A 0 TO1000A 0 TO 50A 0 TO 400A
SERIES 1006X
Data Sheet
INDUSTRIAL GRADE; OUTPUT 4 TO 20mADC; ACCURACY 0.5%FS; FREQUENCY 50 TO 60HZ; LOOP POWER +5 TO +35VDC; RESPONSE 100m-SEC; TEMPERATURE -20° TO +70°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 5A 0 TO 100A 0 TO 500A 0 TO 10A 0 TO 150A 0 TO 800A 0 TO 25A 0 TO 200A 0 TO 1000A 0 TO 50A 0 TO 300A 0 TO 1200A 0 TO 75A 0 TO 400A
SERIES S714
Data Sheet
RMS RESPONDING; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; FREQ. 360 TO 440HZ; POWER +14 TO +32VDC; RESPONSE 75m-SEC; TEMPERATURE -40° TO +85°C; APERTURE 1+3/8 INCH DIA; METAL CASE; CONNECTOR OR BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 5A 0 TO 75A 0 TO 300A 0 TO 10A 0 TO 100A 0 TO 400A 0 TO 25A 0 TO 150A 0 TO 500A 0 TO 50A 0 TO 200A 0 TO 600A
SERIES S786
Data Sheet
RMS RESPONDING; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; FREQUENCY 60HZ; POWER +14 TO +32VDC; RESPONSE 75m-SEC; TEMPERATURE -40° TO +85°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 5A 0 TO 75A 0 TO 400A 0 TO 10A 0 TO 100A 0 TO 500A 0 TO 20A 0 TO 150A 0 TO 600A 0 TO 25A 0 TO 200A 0 TO 800A 0 TO 50A 0 TO 300A 0 TO 1000A
SERIES 1003AM2
Data Sheet
AVG RESPONDING; OUTPUT 0 TO 5VDC; ACCURACY 1%FS; FREQUENCY 57-63HZ (OTHERS AVAILABLE); POWERED BY INPUT; RESPONSE 150m-SEC; TEMPERATURE -20° TO +70°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 10A 0 TO 50A 0 TO 150A 0 TO 15A 0 TO 75A 0 TO 200A 0 TO 20A 0 TO 100A 0 TO 250A 0 TO 25A 0 TO 125A 0 TO 300A 0 TO 30A
SERIES 1001
Data Sheet
CLAMP-ON RMS RESPONDING; OUTPUT 0 TO 5VDC; ACCURACY 1%FS; FREQUENCY DC TO 480HZ; POWER +24 TO +32VDC; RESPONSE 100m-SEC; TEMPERATURE -25° TO +75°C; APERTURE 1+1/2 INCH DIA; METAL CASE; CONNECTOR OR BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 100A 0 TO 750A 0 TO 2000A 0 TO 150A 0 TO 1000A 0 TO 2500A 0 TO 250A 0 TO 1500A 0 TO 3000A 0 TO 500A
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
AC CURRENT TRANSDUCERS CONTINUED (PART THREE OF THREE)
PAGE 9 OF 12
SERIES S461
Data Sheet
CLAMP-ON RMS RESPONDING; OUTPUT 0 TO 5VDC; ACCURACY 1%FS; FREQUENCY DC TO 480HZ; POWER +24 TO +32VDC; RESPONSE 100m-SEC; TEMPERATURE -25° TO +71°C; APERTURE 1+1/2 INCH DIA; PLASTIC CASE; CONNECTOR OR BARRIER SCREW TERMINALS
AC CURRENT RANGES 0 TO 100A 0 TO 750A 0 TO 2000A 0 TO 150A 0 TO 1000A 0 TO 2500A 0 TO 250A 0 TO 1500A 0 TO 3000A 0 TO 500A
DATA SHEETS AT www.a-a-c.com
AC CURRENT DETECTORS NINE MODELS IN ORDER OF CURRENT RANGE
SERIES 870
Data Sheet
HEAVY INDUSTRIAL; OUTPUT SPDT-RELAY (10A CONTACTS); AUTO RESET; ADJUSTABLE (20% TO 100%); POWER 115VAC; FREQUENCY 47-63HZ; TEMPERATURE –20° TO +71°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 1A 0 TO 15A 0 TO 150A 0 TO 2A 0 TO 20A 0 TO 200A 0 TO 5A 0 TO 50A 0 TO 250A 0 TO 10A 0 TO 100A 0 TO 300A
SERIES S871
Data Sheet
WIDE FREQUENCY; OUTPUT SPDT-RELAY (10A CONTACTS); AUTO RESET; ADJUSTABLE (20% TO 100%); POWER 115VAC; FREQUENCY 47-400HZ; TEMPERATURE –20° TO +71°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 1A 0 TO 15A 0 TO 150A 0 TO 2A 0 TO 20A 0 TO 200A 0 TO 5A 0 TO 50A 0 TO 250A 0 TO 10A 0 TO 100A 0 TO 300A
SERIES 882
Data Sheet
CURRENT CONTROLLER: OUTPUT SPDT RELAY (2A CONTACTS); AUTO RESET; ADJUSTABLE (20% TO 100%); POWER 115VAC; FREQUENCY 50-400HZ; TEMPERATURE –20° TO +71°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 1A 0 TO 15A 0 TO 150A 0 TO 2A 0 TO 20A 0 TO 200A 0 TO 5A 0 TO 50A 0 TO 250A 0 TO 10A 0 TO 100A 0 TO 300A
SERIES ACS
Data Sheet
CLAMP-ON SWITCH; OUTPUT SOLID STATE SWITCH; ADJUSTABLE OR FIXED; FREQUENCY 6-100HZ; RESPONSE 120m-SEC; TEMPERATURE -50° TO +65°C; POWERED BY INPUT; OPENING 0.85 X 0.85 INCH; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 250MA 0 TO 5A 0 TO 100A 0 TO 500MA 0 TO 10A 0 TO 150A 0 TO 1A 0 TO 20A 0 TO 200A 0 TO 2A 0 TO 50A 0 TO 250A
SERIES ACS-3
Data Sheet
CLAMP-ON SWITCH; OUTPUT SOLID STATE SWITCH; RANGE SELECTABLE; FREQUENCY 6-100HZ; RESPONSE 120m-SEC; TEMPERATURE -50° TO +65°C; POWERED BY INPUT; OPENING 0.85 X 0.85 INCH; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 1.5 TO 6A, 6 TO 40A OR 40 TO 200A
SWITCH AVAILABLE NORMALLY OPEN OR NORMALLY CLOSED
SERIES ACS-SC
Data Sheet
CLAMP-ON SWITCH; OUTPUT SOLID STATE SWITCH; POWERED BY INPUT; FREQUENCY 6-100HZ; RESPONSE 200m-SEC; TEMPERATURE -50° TO +65°C; OPENING 0.85 X 0.85 INCH; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 1A 0 TO 10A 0 TO 2A 0 TO 20A 0 TO 5A
SERIES 881
Data Sheet
INDUSTRIAL GRADE; OUTPUT SPDT-RELAY (2A CONTACTS); AUTOMATIC RESET; ADJUSTABLE TRIP POINT; POWER 115VAC; FREQUENCY 50-400HZ; TEMPERATURE –20° TO +70°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 12A ............. (TRIP ADJ 2-12A) 0 TO 50A ............. (TRIP ADJ 8-50A) 0 TO 120A ........... (TRIP ADJ 40-120A) 0 TO 250A ........... (TRIP ADJ 100-250A)
SERIES 880B
Data Sheet
INDUSTRIAL GRADE; OUTPUT SOLID STATE SWITCH; AUTOMATIC RESET; POWERED BY INPUT; ADJUSTABLE TRIP POINT; FREQUENCY 50-400HZ; TEMPERATURE –20° TO +70°C; APERTURE 3/4 INCH DIA; PLASTIC CASE; BARRIER SCREW TERMINATIONS
AC CURRENT RANGES 0 TO 12A ............. (TRIP ADJ 2-12A) 0 TO 50A ............. (TRIP ADJ 8-50A) 0 TO 120A ........... (TRIP ADJ 40-120A) 0 TO 250A ........... (TRIP ADJ 100-250A)
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
AC CURRENT DETECTORS CONTINUED (PART THREE OF THREE)
PAGE 10 OF 12
SERIES S212
Data Sheet
AIRCRAFT DO-160; OUTPUT SPDT-RELAY; AUTOMATIC RESET; POWER +24 TO +32VDC; RESPONSE 200M-SEC; TEMPERATURE –55° TO +70°C; APERTURE 3/8 INCH DIA; METAL CASE; CONNECTOR TERMINATIONS; DO-160 ENVIRONMENTAL REQUIREMENTS
AC CURRENT RANGES
0 TO 75A (360-440HZ) RELAY TRIPS @ 0.5AAC ±0.75AAC
DATA SHEETS AT www.a-a-c.com
AC VOLTAGE TRANSDUCERS EIGHT MODELS IN ORDER OF VOLTAGE RANGE
SERIES 108
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; RESPONSE 300m-SEC; POWERED BY INPUT; FREQUENCY 57-63HZ (400HZ AVAILABLE); TEMPERATURE –20° TO +70°C; METAL CASE; BARRIER SCREW TERMINALS OR OPTIONAL CONNECTOR
AC VOLTAGE RANGES 0 TO 50V 0 TO 300V 0 TO 130V 0 TO 500V 0 TO 150V 0 TO 600V 0 TO 270V
SERIES 108X
Data Sheet
PROCESS CONTROL; OUTPUT 4 TO 20mADC; ACCURACY 0.5%FS; RESPONSE 300m-SEC; LOOP POWER +10 TO +35VDC; FREQUENCY 57-63HZ (400HZ AVAILABLE); TEMPERATURE –20° TO +70°C; METAL CASE; BARRIER SCREW TERMINALS OR OPTIONAL CONNECTOR
AC VOLTAGE RANGES 0 TO 50V 0 TO 300V 0 TO 130V 0 TO 500V 0 TO 150V 0 TO 600V 0 TO 270V
SERIES S190
Data Sheet
INDUSTRIAL GRADE; OUTPUT 0 TO 10VDC; ACCURACY 2%FS; RESPONSE 200M-SEC; POWERED BY INPUT; FREQUENCY 47-63HZ (400HZ AVAILABLE); TEMPERATURE 0° TO +60°C; METAL CASE; BARRIER SCREW TERMINATIONS
AC VOLTAGE RANGES 0 TO 130V 0 TO 300V 0 TO 150V 0 TO 600V 0 TO 270V
SERIES V
Data Sheet
UTILITY GRADE; OUTPUT 0 TO 1mADC; ACCURACY 0.25%FS; RESPONSE 400m-SEC; POWERED BY INPUT; FREQUENCY 47-1000HZ; TEMPERATURE –20° TO +70°C; METAL CASE; BARRIER SCREW TERMINATIONS
AC VOLTAGE RANGES 0 TO 150V 0 TO 300V 0 TO 500V
SERIES VX
Data Sheet
PROCESS CONTROL; OUTPUT 4 TO 20mADC; ACCURACY 0.5%FS; RESPONSE 400m-SEC; LOOP POWER +10 TO 32VDC; FREQUENCY 47-1000HZ; TEMPERATURE –20° TO +70°C; METAL CASE; BARRIER SCREW TERMINATIONS
AC VOLTAGE RANGES 0 TO 150V 0 TO 300V 0 TO 500V
SERIES 101M3
Data Sheet
HIGH RESOLUTION; OUTPUT 0 TO 5VDC; ZERO SUPPRESSED INPUT RANGE; ACCURACY 0.5%FS; RESPONSE 1/2-CYCLE OF AC; POWERED BY INPUT; FREQUENCY 57-63HZ; TEMPERATURE -40° TO +70°C; METAL CASE; BARRIER SCREW TERMINALS
AC VOLTAGE RANGES 90 TO 150V
SERIES 102M3
Data Sheet
FAST RESPONSE; OUTPUT 0 TO 5VDC; POWERED BY INPUT; ACCURACY 0.5%FS; ZERO SUPPRESSED INPUT RANGE; RESPONSE 1-CYCLE OF AC; FREQUENCY 340-440HZ; TEMPERATURE -40° TO +70°C; METAL CASE; BARRIER SCREW TERMINATIONS
AC VOLTAGE RANGES 90 TO 175V
105 TO 130V 175 TO 225V
SERIES 105
Data Sheet
ZERO SUPPRESSED INPUT RANGE; OUTPUT 0 TO 5VDC; ACCURACY 0.5%FS; RESPONSE 1-CYCLE OF AC; POWERED BY INPUT; FREQUENCY 57-63HZ; TEMPERATURE -40° TO +70°C; METAL CASE; BARRIER SCREW TERMINATIONS
AC VOLTAGE RANGES 390 TO 490V 455 TO 505V 430 TO 530V
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
DATA SHEETS AT www.a-a-c.com
DC VOLTAGE TRANSDUCER & DETECTOR TWO MODELS IN ORDER OF VOLTAGE RANGE
PAGE 11 OF 12
SERIES S657
Data Sheet
RAIL TRANSIT GRADE; OUTPUT 4 TO 20MADC PROPORTIONAL TO (±) INPUT ABSOLUTE VALUE; ACCURACY 1%FS OVER TEMP; ISOLATION 5KV; RESPONSE 5M-SEC; POWER +22 TO +26VDC; TEMPERATURE –40° TO +85°C; PLASTIC CASE; CONNECTOR AND MATING CONNECTORS INCLUDED
DC VOLTAGE RANGES 0 TO ±150V 0 TO ±750V 0 TO ±300V 0 TO ±1200V 0 TO ±500V 0 TO ±1500V 0 TO ±2000V
SERIES S631
Data Sheet
RAIL TRANSIT GRADE; OUTPUT SPST RELAY (10A CONTACTS); AUTOMATIC RESET @ +365VDC; ACCURACY 1%FS; RESPONSE 110m-SEC; POWER +25 TO +45VDC; TEMPERATURE –25° TO +75°C; PLASTIC CASE; BARRIER SCREW TERMINATIONS
DC VOLTAGE RANGE 0 TO +800V
RELAY TRIPS @
+375VDC ±2VDC
DATA SHEETS AT www.a-a-c.com
AC POWER TRANSDUCERS FIVE MODELS IN ORDER OF POWER RANGE
SERIES W&Q
Data Sheet
UTILITY GRADE; 1φ AND 3φ WATT & VAR TRANSDUCERS; FREQUENCY 60HZ (50 & 400HZ AVAILABLE); OUTPUT 0 TO ±1mADC (±5V & ±10VDC AVAILABLE); ACCURACY 0.25%FS; RESPONSE 400m-SEC; POWERED BY INPUT; TEMPERATURE –20° TO +70°C
AC POWER RANGES 0 TO 6.5AAC AND 85 TO 140VAC
1φ (2-WIRE) ACCEPTS BALANCED 3φ (3-WIRE) OR UNRESTRICTED 3φ (4-WIRE) LOADS & VOLTAGE
SERIES S73
Data Sheet
0-115VAC OR 0-230VAC; OUTPUT 0 TO +5VDC; ACCURACY 2%FS; RESPONSE 400m-SEC; POWER 120VAC; FREQUENCY 57-63HZ; TEMPERATURE 0° TO +50°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC POWER RANGES 0 TO 1KW 0 TO 10KW 0 TO 40KW 0 TO 2KW 0 TO 15KW 0 TO 50KW 0 TO 2.5KW 0 TO 20KW 0 TO 60KW 0 TO 5KW 0 TO 30KW 0 TO 100KW
SERIES 415A
Data Sheet
80-150VAC OR 160-230VAC; OUTPUT 0 TO +5VDC; ACCURACY 2%FS; RESPONSE 400m-SEC; POWERED BY INPUT; FREQUENCY 57-63HZ; TEMPERATURE 0° TO +50°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC POWER RANGES 0 TO 1KW 0 TO 10KW 0 TO 40KW 0 TO 2KW 0 TO 15KW 0 TO 50KW 0 TO 2.5KW 0 TO 20KW 0 TO 60KW 0 TO 5KW 0 TO 30KW 0 TO 100KW
SERIES 416A
Data Sheet
320-560VAC; OUTPUT 0 TO +5VDC; ACCURACY 2%FS; RESPONSE 400m-SEC; POWERED BY INPUT; FREQUENCY 57-63HZ; TEMPERATURE 0° TO +50°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC POWER RANGES 0 TO 4KW 0 TO 40KW 0 TO 100KW 0 TO 10KW 0 TO 50KW 0 TO 200KW 0 TO 20KW 0 TO 80KW
SERIES S217
Data Sheet
160-300VAC & 320-480VAC; OUTPUT 0 TO +5VDC; ACCURACY 2%FS; RESPONSE 400m-SEC; POWERED BY INPUT; FREQUENCY 57-63HZ; TEMPERATURE 0° TO +50°C; APERTURE 3/4 INCH DIA; METAL CASE; BARRIER SCREW TERMINATIONS
AC POWER RANGES 0 TO 2-4KW 0 TO 20-40KW 0 TO 5-10KW 0 TO 25-50KW 0 TO 10-20KW 0 TO 40-80KW
DATA SHEETS AT www.a-a-c.com
FREQUENCY TRANSDUCERS TWO MODELS IN ORDER OF FREQUENCY RANGE
SERIES S350L
Data Sheet
FLIGHT TEST; OUTPUT 0 TO 5VDC; LINEARITY 0.1%FS; INPUT VOLTAGES FROM 20MV TO 50V-RMS; RESPONSE =30/FREQUENCY; POWER +22 TO +30VDC; TEMPERATURE –48° TO +74°C; METAL CASE; CONNECTOR TERMINATIONS
FREQUENCY RANGES 100HZ 1KHZ 5KHZ 200HZ 2KHZ 10KHZ 300HZ 3KHZ 20KHZ 500HZ
SERIES S343
Data Sheet
MIL GRADE; OUTPUT 0 TO 5VDC; ACCURACY 1%FS; RESPONSE 250M-SEC; POWERED BY INPUT; TEMPERATURE –40° TO +70°C; RANGE & ZERO ADJUSTMENTS; METAL CASE; CONNECTOR TERMINATIONS
FREQUENCY RANGES 360 TO 440HZ @ 102-127VAC 360 TO 440HZ @ 200-250VAC AVAILABLE FIELD ADJUSTMENTS
RANGE (±3%) & ZERO (±3%)
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
SF CATA OG L
705 Current Voltage Power & Frequency Transducers PAGE 12 OF 12
5-YEAR WARRANTY: AAC warrants all the products in this catalog to be free from defects in material and workmanship. The warranty applies to the product or parts thereof returned to AAC, with transportation charges prepaid, within five years of the original date of delivery to the original purchaser. Our obligation is limited to servicing, adjusting or replacing, at AAC option, any product or part thereof. Returns to the factory must be authorized in advance. For products sold to a manufacturer that uses it within an assembly made for resale, the remaining warranty is transferable, providing the product is sold as original equipment.
Since 1965 we have continued to strive toward higher levels of product performance, quality and service. AAC provides AC & DC current, voltage, power and frequency transducers for: Industrial automation; laboratory; rail transit; land vehicles; shipboard; aircraft, missile and space flight applications. Products in this catalog represent only part of a broad line of measurement and control instrumentation. In addition, there are numerous and diverse variations available for unique applications.
Quality, reliability and safety are designed in and carefully monitored throughout each process from order entry to shipment. Systems are based on IPC industry standard plus calibration and metrology traceable to NIST. Many of our products are UL, CSA and EU recognized and come with a FIVE YEAR WARRANTY. AAC is a woman owned small business certified to ISO 9001:2000 & AS9100:2004(B).
New and innovative products are continually being developed to meet customer requirements. Product designs focus on the user’s needs and our customers demand for competitive prices and quick delivery. This is the reason we offer a wide product selection from stock and continue to develop application specific modifications and custom products.
Maintaining a long cherished reputation for outstanding customer service is considered an important priority. Every attempt is made to satisfy any reasonable request. AAC computerized tracking schedule continuously monitors customer orders and provides immediate status upon request. An experienced staff stands ready to assist with product selections and to recommend alternative instrumentation solutions.
The fast delivery of cost effective products is due to:
State of the art CAD engineering from circuit analysis to mechanical design.
Computerized inventory for quick access to parts and materials.
Up-to-date in house manufacturing including: coil winding, automated soldering, surface mount technology, encapsulation and more.
In house testing – random vibration, mechanical shock, thermal vacuum, high-energy pulse testing, high current and high voltage testing.
CERTIFIED ISO 9001:2000 & AS9100:2004 REV B
PERRY JOHNSON REGISTRAS
AAC American Aerospace Controls, Inc.
570 Smith Street, Farmingdale New York 11735-1115 USA
Telephone: (631) 694-5100 Toll Free: (888) 873-8559 Facsimile: (631) 694-6739
E-Mail: [email protected]
Website: http://www.a-a-c.com
AAC – American Aerospace Controls, Inc. 570 Smith Street, Farmingdale, New York 11735-1115 Tel: (631) 694-5100 Website: http://www.a-a-c.com
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT SENSOR
SERIES 905B
INPUT INPUT PART NO. CURRENT RANGE PART NO. CURRENT RANGE 905B-50 .......................0 TO ±50mA 905B-1 ..................................... 0 TO ±1A 905B-100 .....................0 TO ±100mA 905B-1.5 .................................. 0 TO ±1.5A 905B-200 .....................0 TO ±200mA 905B-2 ..................................... 0 TO ±2A 905B-500 .....................0 TO ±500mA 905B-5 ..................................... 0 TO ±5A OUTPUT VOLTAGE SIGNAL ........................................................... 0 to ±±5Vdc FS (Full Scale) ACCURACY....................................................................... ±1% FS (±50mV) RIPPLE .............................................................................. 2% FS RMS max. RESPONSE....................................................................... 50 m-sec. max. (10 to 90%) IMPEDANCE ..................................................................... 1000 Ohms ±5%, 5mA to 1A range 666 Ohms 1.5A range, 500 Ohms 2A range, 200 Ohms 5A range TEMPERATURE COEFFICIENT...................................... ±.04% FS/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... ±15Vdc ±1Vdc CURRENT DRAIN............................................................. ±50mAdc max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -55°C to +85°C STORAGE TEMPERATURE RANGE.............................. -55°C to +85°C INSULATION RESISTANCE ............................................ 100 M-ohms (A thru E to case) DIELECTRIC STRENGTH................................................ 350V RMS (A thru E to case) ALTITUDE ......................................................................... Operating sea level to 60,000 ft. VIBRATION ....................................................................... Operating 0.06 in. D.A., 10 to 55 Hz method 201 of MIL-STD-202 SHOCK.............................................................................. Operating 50 g, 11 m-sec half sine pulse method 213 Condition A of MIL-STD-202 MOISTURE RESISTANCE ............................................... Will meet method 106 of MIL-STD-202 and method 507.1 Proc. 1 of MIL-STD-810 OPERATING HUMIDITY................................................... 0% to 95% RH ATTITUDE......................................................................... Meets spec. for any mounting position RIPPLE .............................................................................. 40mV reflected onto pass-thru line WEIGHT ............................................................................ 1.25 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-905B K AACAAC
TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (-) C. SUPPLY (RTN) D. OUTPUT (RTN) E. OUTPUT SIGNAL (+) F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER SERIES S661B PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S661B-100 ...........................0 to 100mA S661B-400 ......................... 0 to 400mA S661B-200 ...........................0 to 200mA S661B-500 ......................... 0 to 500mA S661B-250 ...........................0 to 250mA S661B-750 ......................... 0 to 750mA S661B-300 ...........................0 to 300mA S661B-1A........................... 0 to 1A INPUT POWER RANGE NOMINAL.................................................... See Table mAdc or Ac peak OVERLOAD.............................................................. 0 to ±25 Adc VOLTAGE................................................................. 1000 Vrms FREQUENCY RANGE ............................................. DC to 60Hz OUTPUT VOLTAGE SIGNAL................................................... 0 to ±5Vdc or Ac peak ACCURACY ............................................................ ±1% Full Scale TEMPERATURE COEFFICIENT............................. ±0.02% FS/°C max. OUTPUT IMPEDANCE ............................................ 250 Ohms max. RESPONSE TIME (10 TO 90%) .............................. 1 Msec. max. SHORT CIRCIUT ..................................................... Protected RIPPLE ..................................................................... 1% FS RMS POWER SUPPLY SUPPLY VOLTAGE.................................................. ±±15Vdc (±0.5Vdc) CURRENT DRAIN.................................................... 50mA PROTECTION .......................................................... Reverse Polarity Protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE................................ -40 to +85°C STORAGE TEMPERATURE ................................... -50 to +85 °C OPERATING HUMIDITY.......................................... 0 to 95% RH Operating MOISTURE RESISTANCE ...................................... Will meet method 106 of Mil-Std-202, Method 507.3 procedure 1 of Mil-Std-810. SALT FOG ................................................................ Mil-Std-202, Method 101, 5% salt solution FUNGUS................................................................... Mil-Std-810, Table 508.4 ALTITUDE................................................................. Operating Sea Level to 60,000 Ft. SHOCK ..................................................................... Operating 50g, 11 m-sec half sine pulse Method 213B condition A of Mil-std-202 VIBRATION............................................................... Operating 0.06 inch D.A. 10Hz to 55Hz Method 201A and Random Method 214A Test Condition 1 Level D, 3 Min. Per Axis, 11.95 Overall RMS G, Per Mil-Std-202. ATTITUDE ................................................................ Performs in any position WEIGHT ................................................................... 0.95 lbs. Max. ESD RATING............................................................ 2000V
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S661B-905 A AAC
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE(-) C. SUPPLY RTN D. OUTPUT RTN E. OUTPUT SIGNAL (+) F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT SENSOR SERIES 926
MODEL NUMBER INPUT CURRENT 926-5 .. .................................................. 0 TO ±5 926-10 .................................................. 0 TO ±10 926-15 .................................................. 0 TO ±15 926-20 .................................................. 0 TO ±20 926-25 .................................................. 0 TO ±25 INPUT CURRENT RANGE........................................................... Adc See Table CURRENT OVERLOAD.................................................... ±100Adc Nondestructive/Nonlatching/ Saturated Output OUTPUT VOLTAGE SIGNAL ........................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY....................................................................... ±0.25% FS (±12.5mV) OUTPUT IMPEDANCE..................................................... 100 Ohms max. OUTPUT RIPPLE.............................................................. 0.2% FS RMS max. RESPONSE (10 TO 90%)................................................. 5 m-sec max. TEMPERATURE COEFFICIENT...................................... ±0.006% FS/°C max. OUTPUT PROTECTION .................................................. Short CKT continuously no damage OUTPUT ISOLATION ....................................................... Output/Supply & Case all isolated POWER SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................. 85mAdc max. OVER VOLTAGE PROTECTION..................................... ±35Vdc without damage REVERSE POLARITY PROTECTION .............................10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -55° to +85°C STORAGE TEMPERATURE ............................................ -55° to +100°C OPERATING HUMIDITY................................................... 0% to 95% RH MOISTURE RESISTANCE ............................................... Will meet Method 106 of MIL-STD-202 ALTITUDE ......................................................................... Operating sea level to 60,000 ft. SHOCK.............................................................................. Operating - 50g, 11m-sec half sine pulse (Method 213, Condition A of MIL-STD-202) VIBRATION ....................................................................... Operating - 0.06 inch D.A., 10 to 55Hz (Method 201 of MIL-STD-202) DIELECTRIC STRENGTH................................................ 350V RMS (Method 301 of MIL-STD-202) INSULATION RESISTANCE ............................................ 100-M-Ohms min. @ 500Vdc ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. WEIGHT ............................................................................ 1.25 lbs. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-926 A AACAAC
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT SIGNAL (RTN) D. SPARE E. OUTPUT SIGNAL (+) F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER SERIES S764 PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S764-20 .........................0 to ±20 S764-50…………………0 to ±50 S764-25 .........................0 to ±25 S764-60…………………0 to ±60 S764-30 .........................0 to ±30 S764-70…………………0 to ±70 S764-40…………………0 to ±40 S764-100………………. 0 to ±100 INPUT RANGE.............................................................................. See Table Adc OVERLOAD CONTINUOUS............................................. ±2000Adc FREQUENCY RANGE...................................................... DC to 350Hz OUTPUT VOLTAGE SIGNAL ........................................................... 0 to ±5Vdc FS ACCURACY....................................................................... ±1% FS RESPONSE (10 to 90%) ................................................... 1 m sec. OUTPUT IMPEDANCE..................................................... 10 Ohms LOAD RESISTANCE ........................................................ 10k Ohms min TEMPERATURE COEFFICIENT...................................... ±.02%FS per °c max. OUTPUT PROTECTION .................................................. Short Circuit POWER SUPPLY SUPPLY VOLTAGE ......................................................... +12Vdc to +36Vdc CURRENT DRAIN............................................................. 10mAdc max. PROTECTION................................................................... Reverse polarity protected TRANSIENT PROTECTION............................................. ±60V (T<5mS) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -40° to +85°C STORAGE TEMPERATURE RANGE.............................. -40° to +85°C ISOLATION ....................................................................... Input to output 5KV rms 60Hz/1min. INSULATION RESISTANCE ............................................ 500 M-Ohms @ 500Vdc CASE MATERIAL.............................................................. Molded Plastic meets UL flammability rating 94V-O WEIGHT ........................................................................... 10 oz. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S764 B AAC
TERMINAL IDENTIFICATION 1. SUPPLY VOLTAGE (+) 2. SUPPLY (RTN) 3. OUTPUT (RTN) 4. OUTPUT SIGNAL (+)
TERMINAL SCREWS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32 WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT SENSOR
SERIES S273
TEMPERATURE
PART NO. INPUT CURRENT ACCURACY COEFFICIENT
S273-25 .......................0 to ±25A ........................... 1%................................. .08%
S273-50 .......................0 to ±50A ........................... 1%................................. .06%
S273-100 .....................0 to ±100A ......................... .5%................................. .04%
S273-150 .....................0 to ±150A ......................... .5%................................. .02%
S273-200 .....................0 to ±200A ......................... .5%................................. .02%
S273-250 .....................0 to ±250A ......................... .5%................................. .02%
S273-300 .....................0 to ±300A ......................... .5%................................. .02%
S273-350 .....................0 to ±350A ......................... .5%................................. .02%
OUTPUT VOLTAGE SIGNAL ........................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY....................................................................... % FS See Table di/dt ACCURATELY FOLLOWED..................................... Better than 50A/u-sec. DELAY TIME ..................................................................... Better than 1u-sec. BANDWIDTH .................................................................... DC to 100KHz IMPEDANCE ..................................................................... 500 Ohms (25A) 200 Ohms max. (50 -350A) TEMPERATURE COEFFICIENT...................................... FS/°C max. See Table POWER SUPPLY SUPPLY VOLTAGE ......................................................... ±15Vdc ±1Vdc CURRENT DRAIN............................................................. 100mAdc max. REVERSE POLARITY PROTECTION ............................. 10µA max. current drain no damage. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -55° to +85°C STORAGE TEMPERATURE ............................................ -55° to +85°C OPERATING HUMIDITY................................................... 0% to 95% RH MOISTURE RESISTANCE ............................................... Will meet Method 106 of MIL-STD-202 & Method 507.1, Procedure I of MIL-STD-810 ALTITUDE ......................................................................... Operating: Sea level to 60,000 ft. Non-operating: Sea level to 120,000 ft. (Method 105, Condition A of MIL-STD-202) SHOCK.............................................................................. Non-operating: 50g, 11m-sec half sine pulse (Method 213, Condition A of MIL-STD-202) VIBRATION ....................................................................... Non-operating: 0.06 in. D.A., 10 to 55Hz (Method 201 of MIL-STD-202) DIELECTRIC STRENGTH................................................ 350V RMS dielectric withstanding voltage (Method 301 of MIL-STD-202) INSULATION RESISTANCE ............................................ 10M-Ohms min. (Method 302, Condition A of MIL-STD-202) ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. WEIGHT ........................................................................... 14 oz. max.
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (-) C. SUPPLY VOLTAGE (RTN) D. OUTPUT SIGNAL (RTN) E. OUTPUT SIGNAL (+) F. CASE GROUND
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S273-925 K AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER
SERIES S449
TEMPERATURE
PART NO. INPUT CURRENT ACCURACY COEFFICIENT
S449-25 .........................0 to ±25................................ ±1.0% ............................±0.05%
S449-40 .........................0 to ±40................................ ±0.5% ............................±0.03%
S449-50 .........................0 to ±50................................ ±0.5% ............................±0.025%
S449-60 .........................0 to ±60................................ ±0.5% ............................±0.025%
INPUT CURRENT RANGE................................................................... Adc or ac peak See Table FREQUENCY RANGE.............................................................. DC to 2KHz continuous operation CURRENT OVERLOAD............................................................ Unlimited (Nondestructive Nonlatching/ Saturated Output) OUTPUT VOLTAGE SIGNAL ................................................................... 0 to ±5.0Vdc FS (Full Scale) ACCURACY............................................................................... See Table OUTPUT IMPEDANCE............................................................. 400 Ohms max. RESPONSE (10 to 90%) ........................................................... 1u-sec max. BANDWIDTH ............................................................................ DC to 100KHz TEMPERATURE COEFFICIENT.............................................. FS/°C max. See Table OUTPUT NOISE ....................................................................... 10mV RMS max. LINEAR OVER RANGE ............................................................ 10% above FS POWER SUPPLY SUPPLY VOLTAGE ................................................................. ±15Vdc ±250mV CURRENT DRAIN..................................................................... ±40mA max. MAX. OVER VOLTAGE ............................................................ ±17Vdc continuous (Nondestructive) REVERSE POLARITY .............................................................. 10µA drain (Nondestructive) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE (TC) ........................................ -40° to +71°C STORAGE TEMPERATURE .................................................... -55° to +125°C ISOLATION : INPUT/OUTPUT/CASE..................................... 1050V RMS max. INSULATION RESISTANCE .................................................... 200M-Ohms @ 500Vdc CASE ........................................................................................ Hermetic seal FINISH ....................................................................................... Fuse Tin Plate WEIGHT ................................................................................... 4 oz. max.
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (-) C. SUPPLY (RTN) D. OUTPUT (RTN) E. OUTPUT (+)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S449 D AAC
BIDIRECTIONAL CURRENT TRANSDUCER
SERIES S745 RESPONSE TEMP. PART NO. INPUT RANGE ACCURACY TIME BANDWIDTH COEFF. S745-40 ........... 0 to ±40 Adc.............. ±1 ................. 2u-sec ........ 175Khz ........... .05% S745-75............ 0 to ±75 Adc.............. ±0.75 ............ 1.5u-sec ..... 233Khz ........... .04% S745-150.......... 0 to ±150 Adc............ ±0.5 .............. 1.0u-sec ..... 350Khz ........... .03% S745-250.......... 0 to ±250 Adc............ ±0.5 .............. 1.0u-sec ..... 350Khz ........... .03% INPUT CURRENT RANGE NOMINAL .................................................. See Table OVERLOAD ............................................................ Unlimited (Nondestructive Nonlatching Saturated output) FREQUENCY RANGE............................................ DC to 20KHz OUTPUT VOLTAGE SIGNAL ................................................. 0 to ±5Vdc (Full Scale) ACCURACY (ROOM TEMP) .................................. % FS see table TEMPERATURE COEFFICIENT ............................ Per °C max. see table OUTPUT IMPEDANCE ........................................... 10 Ohms max. RESPONSE TIME (10 TO 90%) ............................. Max. see table BANDWIDTH .......................................................... DC to see table OUTPUT PROTECTION......................................... Short Circuit OUTPUT LOAD....................................................... 5K Ohm min. POWER SUPPLY SUPPLY VOLTAGE ................................................ ±12Vdc (±1Vdc) CURRENT DRAIN .................................................. +15mA max -5mA max. PROTECTION......................................................... Reverse Polarity Protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE............................... -55 to +100°C STORAGE TEMPERATURE .................................. -55°C to +100 °C RADIATION............................................................. Operating as specified with a total dose of 1 KRAD (SI). SEL of 37 MeV (no latch or up-set). SHOCK ................................................................... 100 g, 6 m-sec half sine pulse VIBRATION............................................................. 50g HUMIDITY............................................................... 0 to 100% RH Operating INSULATION RESISTANCE................................... 500M-Ohms @ 500Vdc DIELECTRIC STRENGTH ..................................... 1500Vdc FINISH .................................................................... Fuse Tin Plate WEIGHT.................................................................. 0.49 lbs. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S745A AAC
TERMINAL IDENTIFICATION
A. SUPPLY (+) B. SUPPLY (RTN) C. SUPPLY (-) D. OUTPUT (+) E. OUTPUT (RTN)
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER SERIES 929 PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE 929-50.......................... 0 to ±50 929-200………………… 0 to ±200 929-75 .......................... 0 to ±75 929-250………………… 0 to ±250 929-100........................ 0 to ±100 929-300………………… 0 to ±300 929-150………………….0 to ±150 929-400………………… 0 to ±400 INPUT RANGE ........................................................................... See Table Adc or AC Peak OVERLOAD CONTINUOUS ........................................... ±5000Adc FREQUENCY RANGE.................................................... DC to 350KHz OUTPUT VOLTAGE SIGNAL ......................................................... 0 to ±5Vdc FS ACCURACY (Over Temperature Range)........................ ±1% FS (note 1) RESPONSE (10 to 90%)................................................. 1 u-sec. max. OUTPUT IMPEDANCE................................................... 25 Ohms LOAD RESISTANCE ..................................................... 5k Ohms min OUTPUT PROTECTION................................................. Short Circuit POWER SUPPLY SUPPLY VOLTAGE ....................................................... +10Vdc to +34Vdc CURRENT DRAIN .......................................................... 8mAdc max. PROTECTION................................................................. Reverse polarity protected TRANSIENT PROTECTION ........................................... ±60V (T<5mS) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE ......................... -40° to +85°C STORAGE TEMPERATURE RANGE............................. -55° to +125°C HUMIDITY (Operating).................................................... 0% to 95%RH MOISTURE RESISTANCE ............................................. MIL-STD-202 Method 106 (note 2) RANDOM VIBRATION (Operating)................................. MIL-STD-810F, Proc.1,Cat.12, WO=.095G2/Hz,
Time1 hr, Fig. 514.5C-8 Overall level 12.G-RMS SHOCK ........................................................................... 50g 11m-sec. half sine pulse ISOLATION..................................................................... Input to output 5KV rms 60Hz/1min. INSULATION RESISTANCE........................................... 500 M-Ohms @ 500Vdc CASE MATERIAL ........................................................... Molded Plastic meets UL flammability rating 94V-O (color light gray) WEIGHT ......................................................................... 6 oz. Max. NOTE 1: Specified accuracy includes the combined worst case effects of Zero Offset, Temperature, Hysteresis, Supply Swings and Current Cable Positioning. NOTE 2: Meets Specified Moisture requirements with option C & D only.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-929 B AAC
TERMINAL IDENTIFICATION 1. SUPPLY VOLTAGE (+) 2. SUPPLY (RTN) 3. OUTPUT (RTN) 4. OUTPUT SIGNAL (+) 5-9. SPARE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Cod
e Id
ent.
No.
159
48
AA
C
Amer
ican
Aer
ospa
ce C
ontro
ls In
c.,
570
Smith
Stre
et,
Farm
ingd
ale,
New
Yor
k 1
1735
Te
l:(63
1) 6
94-5
100
Fax
:(631
) 694
-673
9
BID
IREC
TIO
NAL
CU
RR
ENT
TRAN
SDU
CER
SE
RIE
S S
651
PAR
T N
UM
BER
IN
PUT
CU
RR
ENT
OVE
R R
ANG
E
R
ANG
E
S651
-100
-C
0 TO
±10
0Adc
±1
00 T
O ±
125A
dc
S6
51-2
00-C
0
TO ±
200A
dc
±200
TO
±25
0Adc
IN
PUT
RAN
GE
......
......
......
......
......
......
......
......
...
See
Tabl
e O
VER
RAN
GE
CAP
ABIL
ITY
......
......
......
Se
e Ta
ble
CU
RR
ENT
OVE
RLO
AD...
......
......
......
.....
± 50
00 a
mps
. DC
con
tinuo
us
OU
TPU
T VO
LTAG
E SI
GN
AL .
......
......
......
......
......
. 0
to ±
5Vd
c FS
( ±5
to ±
6.25
Vdc
OR
) AC
CU
RAC
Y...
......
......
......
......
......
......
.....
±
1% (±
50m
V) O
ver -
10°C
to +
65°C
LO
W T
EMP.
OPE
RAT
ION
......
......
......
....
@ -4
0°C
to -1
0°C
Acc
urac
y / L
inea
rity
±2.
5% F
S AC
CU
RAC
Y O
VER
RAN
GE(
OR
)....
......
. 2.
5% F
S LI
NEA
RIT
Y...
......
......
......
......
......
......
......
. ±0
.5%
FS
R
ESPO
NSE
(10
TO 9
0%)..
......
......
......
...
100
u-se
c m
ax.
OU
TPU
T LO
AD C
UR
REN
T...
......
......
.....
5mA
max
. O
UTP
UT
IMPE
DAN
CE
......
......
......
......
...
100
Ω m
ax.
POW
ER S
UPP
LY
SUPP
LY V
OLT
AGE
......
......
......
......
......
. +
22 to
32V
dc
CU
RR
ENT
DR
AIN
......
......
......
......
......
....
140m
A m
ax.
REV
ERSE
PO
LAR
ITY
PRO
TEC
TIO
N...
. 10
uA m
ax. c
urre
nt d
rain
with
out d
amag
e TR
ANSI
ENT
......
......
......
......
......
......
......
.. 40
V fo
r 20
m-s
ec
ENVI
RO
NM
ENTA
L AN
D P
HYS
ICAL
CH
ARAC
TER
ISTI
CS
OPE
RAT
ING
TEM
PER
ATU
RE
......
......
...
-40°
C to
+65
°C
STO
RAG
E TE
MPE
RAT
UR
E...
......
......
...
-55°
C to
+71
°C
OPE
RAT
ING
HU
MID
ITY
......
......
......
......
. 0%
to 9
5% R
H
MO
ISTU
RE
RES
ISTA
NC
E ...
......
......
.....
Will
mee
t Met
hod
106
of M
IL-S
TD-2
02 &
Met
hod
507.
1, P
roc.
1 o
f MIL
-STD
-810
AL
TITU
DE
......
......
......
......
......
......
......
.....
Ope
ratin
g: S
ea L
evel
to 2
7,00
0 FT
.
N
on-O
pera
ting:
Sea
Lev
el to
70,
000F
t. VI
BRAT
ION
......
......
......
......
......
......
......
...
20 to
40H
z +
6dB/
Oct
ave
40 to
120
Hz
0.02
G2 /H
z, 1
20
to 1
50 S
lope
By
End
Poin
t, 15
0 to
800
Hz
0.04
G2 /H
z,
800-
2000
Hz
-6dB
/Oct
ave
ACC
ELER
ATIO
N .
......
......
......
......
......
....
Ope
ratin
g ±5
gs
In A
ll Ax
es, B
oth
Dire
ctio
ns
DIE
LEC
TRIC
STR
ENG
TH .
......
......
......
.. 35
0V R
MS
Term
inal
s 1-
5 &
Cas
e.
INSU
LATI
ON
RES
ISTA
NC
E ...
......
......
...
1 M
Ω @
200
Vdc
ATTI
TUD
E...
......
......
......
......
......
......
......
.. U
nit W
ill Pe
rform
As
Spec
ified
Whe
n M
ount
ed In
Any
Po
sitio
n.
SHO
CK
......
......
......
......
......
......
......
......
.. O
pera
ting:
20g
, Pea
k Te
rmin
al S
awto
oth
Puls
e 11
Milli
se
cond
s D
urat
ion,
All
Plan
es, B
oth
Dire
ctio
ns.
WEI
GH
T ...
......
......
......
......
......
......
......
....
1.5
lbs.
max
. C
OM
PON
ENTS
D
ERAT
ING
(EEE
CO
MPO
NEN
TS).
......
. D
erat
ed T
o Th
e In
tent
of N
aval
Air
Syst
ems
Com
man
d
AS-4
613.
M
ICR
OC
IRC
UIT
S...
......
......
......
......
......
.. M
IL-M
-385
10 C
lass
B Q
PL o
r DES
C D
WG
. SE
MIC
ON
DU
CTO
RS
......
......
......
......
......
M
IL-S
-195
00 (J
ANTX
) C
APAC
ITO
RS
......
......
......
......
......
......
.....
MIL
-C-3
9003
, MIL
-C-3
9014
(Lev
el R
) R
ESIS
TOR
S...
......
......
......
......
......
......
....
MIL
-R-3
9007
, -39
008,
-390
35,-5
5182
(Lev
el R
) TR
ANSF
OR
MER
S &
IND
UC
TOR
S...
.....
MIL
-T-2
7 (C
lass
S)
TE
RM
INAL
IDEN
TIFI
CAT
ION
A. S
UPP
LY V
OLT
AGE
(+)
B.
SU
PPLY
(RTN
)
C.
OU
TPU
T (R
TN)
D
. O
UTP
UT
SIN
GAL
(+)
E.
CAS
E G
RO
UN
D
F. S
PAR
E
Dim
ensi
ons
in In
ches
, T
oler
ance
s: .
XX ±
.03
.X
XX ±
.01
0
D
raw
ing
Num
ber
Rev
.
700-
S651
-942
H
AAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY (RTN) C. OUTPUT (RTN) D. OUTPUT SIGNAL (+)
E. SPARE
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S784 B AAC
BIDIRECTIONAL CURRENT TRANSDUCER SERIES S784 PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S784-100..............................0 to ±100 S784-400.............................. 0 to ±400 S784-200..............................0 to ±200 S784-500.............................. 0 to ±500 S784-250..............................0 to ±250 S784-600.............................. 0 to ±600 S784-300..............................0 to ±300 S784-750.............................. 0 to ±750 INPUT RANGE ............................................................................. See Table Adc FREQUENCY ................................................................... DC to 1kHz OVERLOAD CURRENT CONTINOUSE ......................... 10KAdc OUTPUT VOLTAGE SIGNAL........................................................... 0 to ±5Vdc FS ACCURACY...................................................................... ±1% FS RESPONSE TIME (10 TO 90%) ..................................... 500 u-sec. max. OUTPUT IMPEDANCE .................................................... 250 Ohms max. TEMPERATURE COEFFICIENT..................................... ±.02%FS Per°c max. OUTPUT PROTECTION.................................................. Short CKT RECOMMEND OUTPUT LOAD....................................... 50KΩ or greater POWER SUPPLY SUPPLY VOLTAGE ......................................................... +16Vdc to +40Vdc nominal CURRENT DRAIN............................................................ 10mA max. REVERSE POLARITY PROTECTION ............................ 100µA max. Current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -40°C to +85°C STORAGE TEMPERATURE RANGE ............................. -55°C to +85°C DIELECTRIC STRENGTH ............................................... 350V RMS MIL-STD-202 Method 301 MOUNTING ...................................................................... Rigid in any position INSULATION RESISTANCE............................................ 200 M-Ohms min. MIL-STD-202 Method 302 Test Condition A WEIGHT ........................................................................... 9 oz. max. DO-160D ENVIRONMENT CATEGORY SECTION TEMPERATURE & ALTITUDE A2 4 TEMPERATURE VARIATION A 5 HUMIDITY A 6 SHOCK & CRASH SAFTY REQ’D 7 VIBRATION H2 CURVE C&R 8 EXPLOSION PROOF X 9 FLUID SUSCEPTIBILITY X 11 SAND AND DUST X 12 FUNGUS RESISTANCE F 13 SALT SPRAY X 14 MAGNETIC EFFECT X 15 VOLTAGE SPIKE A 17 AUDIO FREQUENCY SUSCEPTIBILITY A 18 INDUCED SIGNAL SUSCEPTIBILITY A 19 RADIO FREQUENCY SUSCEPTIBILITY A 20 EMMISION OF RADIO FREQUENCY ENERGY Z 21 LIGHTNING INDUCED TRANSIENT SUSCEPTIBILITY A3C3 22 LIGHTNING DIRECT EFFECT X 23 STATIC DISCHARGE A
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER SERIES 947
TEMPERATURE PART NO. INPUT CURRENT COEFFICIENT
947-100 ................................ 0 to ±100................................... .02% 947-200 ................................ 0 to ±200................................... .01% 947-300 ................................ 0 to ±300.................................. .01% 947-400 ................................ 0 to ±400.................................. .01% 947-500 ................................ 0 to ±500.................................. .01% 947-600 ................................ 0 to ±600.................................. .01% INPUT RANGE ........................................................................................ Amps. DC or AC peak. See Table CURRENT OVERLOAD.............................................................. ±5000 amps. DC continuous FREQUENCY .............................................................................. DC to 100KHz OUTPUT VOLTAGE SIGNAL...................................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY................................................................................. ± 0.5% FS LINEARITY................................................................................... ±0.1% FS DI DT CAPABILITY...................................................................... 50A per u-sec DELAY TIME................................................................................ 1 u-sec OUTPUT IMPEDANCE ............................................................... 100 Ohms max. TEMPERATURE COEFFICIENT................................................ % FS per °C. See Table POWER SUPPLY SUPPLY VOLTAGE..................................................................... ±15Vdc ±1Vdc CURRENT DRAIN....................................................................... 150mA max. REVERSE POLARITY PROTECTION ....................................... 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE................................................... - 20° C to 70°C STORAGE TEMPERATURE ...................................................... - 45°C to 85°C OPERATING HUMIDITY............................................................. 0% to 95% RH INSULATION RESISTANCE....................................................... 100 M-Ohms min. ATTITUDE ................................................................................... Unit will perform as specified when mounted in any position. SHOCK ........................................................................................ Operating: 50g, 11 m-sec half sine pulse Method 213 Condition A of MIL-STD-202 WEIGHT ...................................................................................... 1.5 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-947 C AACAAC
TERMINALS: 6-32 SCREWS, .325” CENTER TO CENTER SPACING, ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO .26” WIDE.
TERMINAL IDENTIFICATION 1. SUPPLY VOLTAGE (+) 2. SUPPLY VOLTAGE (-) 3. SUPPLY (RTN) 4. OUTPUT (RTN) 5. OUTPUT SIGNAL (±)
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT SENSOR SERIES 943A
TEMPERATURE PART NO. INPUT CURRENT COEFFICIENT SUPPLY CURRENT 943-100................... 0 to ±100 ......................... .04% ...................................... 85mA 943-200................... 0 to ±200 .......................... .04% ...................................... 115mA 943-300................... 0 to ±300 .......................... .02% ...................................... 165mA 943-400................... 0 to ±400 .......................... .02% ...................................... 215mA 943-500................... 0 to ±500 .......................... .02% ...................................... 265mA 943-600................... 0 to ±600 .......................... .01% ...................................... 265mA 943-750................... 0 to ±750 .......................... .01% ...................................... 265mA 943-800................... 0 to ±800 .......................... .01% ...................................... 265mA 943-1000................. 0 to ±1000 ......................... .01% ...................................... 265mA INPUT CURRENT RANGE........................................................................................ Amps. DC or AC peak. See Table CURRENT OVERLOAD.............................................................. ±5000 amps. DC continuous FREQUENCY .............................................................................. DC to 350KHz OUTPUT VOLTAGE SIGNAL ..................................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY................................................................................. ± 0.5% FS LINEARITY .................................................................................. ±0.1% FS BANDWIDTH .............................................................................. DC to 350KHz RESPONSE TIME (10 to 90%) ................................................... 1 u-sec OUTPUT IMPEDANCE............................................................... 100 Ohms max. TEMPERATURE COEFFICIENT................................................ % FS per °C. See Table POWER SUPPLY SUPPLY VOLTAGE .................................................................... ±15Vdc ±1Vdc CURRENT DRAIN....................................................................... See Table mA max. REVERSE POLARITY PROTECTION ....................................... 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE .................................................. - 55° C to +85°C STORAGE TEMPERATURE ...................................................... - 55°C to +100°C OPERATING HUMIDITY............................................................. 0% to 95% RH MOISTURE RESISTANCE ......................................................... Will meet Method 106 of MIL-STD -202 & Method 507.1, Proc. 1 of MIL-STD-810 ALTITUDE ................................................................................... Operating: Sea level to 70,000 ft. RANDOM VIBRATION................................................................ Operating MIL-STD-810E Category 5, Proc. 1, WO=0.012G2Hz, duration 1 Hr. Figure 514. 4-8 suggested vibration levels for high performance Aircraft 12.5 G-RMS composite min. DIELECTRIC STRENGTH.......................................................... 350V RMS terminals 1-4 to 5 & case INSULATION RESISTANCE ...................................................... 100 M-Ohms min. ATTITUDE................................................................................... Unit will perform as specified when mounted in any position. SHOCK........................................................................................ Operating: 50g, 11 m-sec half sine pulse Method 213 Condition A of MIL-STD- 202 WEIGHT ...................................................................................... 1.5 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-943A A AACAAC
MOLDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE.
TERMINAL IDENTIFICATION 1- A. SUPPLY VOLTAGE (+) 2- B. SUPPLY & OUTPUT (RTN) 3- C. SUPPLY VOLTAGE (-) 4- D. OUTPUT SIGNAL (+) 5- E. CASE GROUND F. SPARE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT SENSOR SERIES 944
PART NUMBER INPUT RANGE 944-600 ............................................... 0 TO ±600 944-800 ............................................... 0 TO ±800 944-1000 ........................................... 0 TO ±1000 944-1500 ........................................... 0 TO ±1500 944-2000 ........................................... 0 TO ±2000 INPUT CURRENT RANGE.............................................................................. Amps. DC or AC peak. See Table CURRENT OVERLOAD.................................................... ±5000 Amps. DC continuous. FREQUENCY .................................................................... DC to 20KHz OUTPUT VOLTAGE SIGNAL ........................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY....................................................................... ±1% FS LINEARITY ........................................................................ ±.5% FS DI DT CAPABILITY ........................................................... 25A per u-sec OUTPUT IMPEDANCE..................................................... 100 Ohms max. TEMPERATURE COEFFICIENT...................................... ±0.04% FS/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... ±15Vdc ±1Vdc CURRENT DRAIN............................................................. 50mA max. REVERSE POLARITY PROTECTION ............................. 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -55° to +85°C STORAGE TEMPERATURE ............................................ -55° to +100°C OPERATING HUMIDITY................................................... 0% to 95% RH MOISTURE RESISTANCE ............................................... Will meet Method 106 of MIL-STD-202 & Method 507.1, Proc. 1 of MIL-STD-810 ALTITUDE ......................................................................... Operating: Sea level to 70,000 ft. RANDOM VIBRATION...................................................... Operating MIL-STD-810E Category 5, Proc. 1, WO=0.012G2Hz, Duration 1 hr., Figure 514.4-8 Suggested Vibration levels for high performance Aircraft 12.5 G-RMS composite min. DIELECTRIC STRENGTH................................................ 350V RMS terminals 1-4 to 5 & case INSULATION RESISTANCE ............................................ 100 M-Ohms min. ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. SHOCK.............................................................................. Operating: 50g, 11 m-sec half sine pulse Method 213 Condition A of MIL-STD-202. WEIGHT ............................................................................ 1.5 lbs. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-944 C AACAAC
TERMINAL IDENTIFICATION 1- A. SUPPLY VOLTAGE (+) 2- B. SUPPLY & OUTPUT (RTN) 3- C. SUPPLY VOLTAGE (-) 4- D. OUTPUT SIGNAL (+) 5- E. CASE GROUND F. SPARE
MOLDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER SERIES 948
PART NUMBER INPUT CURRENT 948-600 ............................................. 0 TO ±600 948-800 ............................................. 0 TO ±800 948-1000 ........................................... 0 TO ±1000 948-1500 ........................................... 0 TO ±1500 948-2000 ........................................... 0 TO ±2000 INPUT RANGE.............................................................................. Amps. DC or AC peak. See Table CURRENT OVERLOAD.................................................... ±5000 Amps. DC continuous FREQUENCY .................................................................... DC to 20KHz OUTPUT VOLTAGE SIGNAL ........................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY....................................................................... ±1% FS LINEARITY ........................................................................ ±.5% FS DI DT CAPABILITY ........................................................... 25A per u-sec OUTPUT IMPEDANCE..................................................... 100 Ohms max. TEMPERATURE COEFFICIENT...................................... ±0.04% FS/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... ±15Vdc ±1Vdc CURRENT DRAIN............................................................. 50mA max. REVERSE POLARITY PROTECTION .............................10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -20° to +70°C STORAGE TEMPERATURE ............................................ -45° to +85°C OPERATING HUMIDITY................................................... 0% to 95% RH INSULATION RESISTANCE ............................................ 100 M-Ohms min. ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. SHOCK.............................................................................. Operating: 50g, 11m-sec half sine pulse (Method 213, Condition A of MIL-STD-202) WEIGHT ............................................................................ 1.5 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-948 C AACAAC
TERMINAL IDENTIFICATION
1. SUPPLY VOLTAGE (+) 2. SUPPLY VOLTAGE (-) 3. SUPPLY (RTN) 4. OUTPUT (RTN) 5. OUTPUT SIGNAL (±)
TERMINALS: 6-32 SCREWS, .325” CENTER TO CENTER SPACING, ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO .26” WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
*NOTE: SERIES 909M4 NORMALLY SUPPLIED WITH 4 TERMINAL BARRIER STRIP. AVAILABLE WITH 6 PIN OPTIONAL CONNECTOR PT02E-10-6P OR EQUIVALENT. ADD LETTER “C” AFTER MODEL NUMBER FOR CONNECTOR OPTION. (REFERENCE: CONNECTOR MATES WITH PT06A-10-6S (SR) OR EQUIVALENT).
BIDIRECTIONAL CURRENT TRANSDUCER SERIES 909M4
REMOVEABLE YOKE TYPE
MODEL NUMBER * INPUT RANGE 909M4-150........................................... 0 TO ±150 909M4-250........................................... 0 TO ±250 909M4-500........................................... 0 TO ±500 909M4-750........................................... 0 TO ±750 909M4-1000....................................... 0 TO ±1000 909M4-1500....................................... 0 TO ±1500 909M4-2000....................................... 0 TO ±2000 909M4-2500....................................... 0 TO ±2500 INPUT CURRENT RANGES........................................................ 0 to (FS) Full Scale, See Table CURRENT OVERLOAD................................................... 100 times FS OUTPUT VOLTAGE SIGNAL........................................................... 0 to ±5Vdc FS ACCURACY...................................................................... ±1% FS RESPONSE...................................................................... 200 µ-sec. max. TEMPERATURE COEFFICIENT..................................... ±.05% FS/°C max. OUTPUT IMPEDANCE .................................................... 100 Ohms max. OUTPUT SHORT-CIRCUIT DURATION......................... Indefinite POWER SUPPLY SUPPLY VOLTAGE ......................................................... ±15Vdc ±2Vdc SUPPLY BURDEN............................................................ +15Vdc 100mA max. -15Vdc 25mA max. PROTECTION .................................................................. Reverse Polarity Protection ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -25° to +75°C STORAGE TEMPERATURE RANGE ............................. -55° to +85°C ISOLATION....................................................................... Input/Output/Case (Supply & Output / Common) CASE MATERIAL ............................................................. Aluminum Casting FINISH .............................................................................. Black Anodize Finish WEIGHT ........................................................................... 18 oz.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-909M4 C AACAAC
TERMINAL IDENTIFICATION BARRIER CONNECTOR 1 OUTPUT SIGNAL (+) A 2 SUPPLY & OUTPUT (RTN) B 3 SUPPLY VOLTAGE (+) C 4 SUPPLY VOLTAGE (-) D SPARE E SPARE F
BARRIER MOLDED TERMINAL BARRIER WITH 5-40 TERMINAL SCREWS AND .375 CENTER DISTANCES. TERMINALS ACCEPT WIRE SIZE UP TO #16 AWG WITH LUGS TO .281 IN. WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
BIDIRECTIONAL CURRENT TRANSDUCER SERIES 9000
REMOVABLE YOKE TYPE PART NO. INPUT RANGE PART NO. INPUT RANGE 9000-150......................0 to ±150 9000-1000................................ 0 to ±1000 9000-250......................0 to ±250 9000-1500................................ 0 to ±1500 9000-500......................0 to ±500 9000-2000................................ 0 to ±2000 9000-750......................0 to ±750 9000-2500................................ 0 to ±2500 INPUT CURRENT RANGE................................................................... See Table CURRENT OVERLOAD............................................................ Unlimited Nondestructive OUTPUT VOLTAGE SIGNAL ................................................................... 0 to ±5Vdc FS (Full Scale) ACCURACY............................................................................... ±1% FS RESPONSE (10 to 90%) ........................................................... 200 u-sec max. OUTPUT IMPEDANCE............................................................. 100Ω max. TEMPERATURE COEFFICIENT.............................................. ±0.05% FS/°C typ SHORT CIRCUIT DURATION.................................................. Continuous POWER SUPPLY SUPPLY VOLTAGE ................................................................. ±15Vdc ±1Vdc CURRENT DRAIN..................................................................... 100mA max. at +15Vdc 25mA max. at -15Vdc REVERSE POLARITY .............................................................. No damage, 10uA current drain ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .................................. -25° to +75°C STORAGE TEMPERATURE RANGE...................................... -55° to +85°C ISOLATION ............................................................................... Input/Output/Case (Supply & Output Common) CASE MATERIAL ..................................................................... Molded Plastic Meets UL Flammability Rating 94V- 0 WEIGHT ................................................................................... 12 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-9000 D AACAAC
NOTE: 1. NORMALLY SUPPLIED WITH 5 PIN TERMINAL BARRIER STRIP. MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS, .325 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 16AWG AND WIRE LUGS TO .250 IN. WIDE. AVAILABLE WITH 6 PIN OPTIONAL CONNECTOR MS3112E-10-6P OR EQUIVALENT. ADD LETTER -C AFTER PART NUMBER FOR CONNECTOR OPTION.
TERMINAL IDENTIFICATION BARRIER CONNECTOR 1 OUTPUT (+) A 2 OUTPUT (RTN) B 3 SUPPLY VOLTAGE (+15V) C 4 SUPPLY VOLTAGE (RTN) D 5 SUPPLY VOLTAGE (-15) E SPARE F
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S630 D AACAAC
DC CURRENT TRANSDUCER PART NUMBER S630-2500
INPUT MEASURING RANGE (CONTINUOUS) 0 to ± 1000Adc FS (Full Scale) (TRANSIENT) ..... 1422A RMS (1 min) 1375A RMS (4 min) 1161A RMS (30 min) 2168A peak (5 sec.) 2514A tr (18 M-sec.) OUTPUT CURRENT SIGNAL ................................. 250uA per 1A Input TURN RATIO ........................................... 4000 to 1 ACCURACY ............................................ 0.5% FS (-25 to +70°C) LINEARITY .............................................. ± 0.1% max. up to 630mA max. LOAD........................................................ 5.5 Ohms max. RESPONSE ............................................. 1M-sec. max. POWER SUPPLY SUPPLY VOLTAGE ................................ ±24Vdc ±1Vdc CURRENT DRAIN ................................... 650mA max. PROTECTION ......................................... Reverse Polarity Protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -25°C to +75°C STORAGE TEMPERATURE................... -40°C to +85°C SHOCK & VIBRATION ........................... IAW ADTRANZ Doc. ABB-ES-091291-1 OPERATING HUMIDITY ....................... 0 to 95% Relative Humidity INSULATION RESISTANCE .................. 200 M-ohms @ 500Vdc DIELECTRIC STRENGTH ..................... 3.3Kv RMS 60Hz PRIMARY BAR VOLTAGE ..................... 2Kv RMS max. CASE........................................................ Moulded Plastic (GE Lexan) Meets UL Flammability Rating 94 V-0 WEIGHT .................................................. 6.5 lbs. max.
TERMINAL IDENTIFICATION 1. SUPPLY VOLTAGE (+)
2. SUPPLY VOLTAGE (-)
3. OUTPUT
4. SPARE
5. SPARE
NOTE: 1. MOULDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE. TORQUE 8 IN-LB MAX. 2. PART TO BE IDENTIFIED WITH ADTRANZ PART NUMBER & REVISION LEVEL IN ACCORDANCE WITH SAE AS478-30, LATEST REVISION. CHARACTER HEIGHT SHALL BE .50 INCH MAX. APPROX. WHERE SHOWN. 3. REFERENCE DOCUMENT NO. E301-005.RFP (XIL). 4 .RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT LOCKWASHER AND #8 FLAT WASHER. TORQUE MAXIMUM 18 IN-LB.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT SENSOR SERIES 903B
INPUT INPUT PART NO. CURRENT RANGE PART NO. CURRENT RANGE 903B-5 .........................0-5mA 903B-200 ................................. 0-200mA 903B-10 .......................0-10mA 903B-500 ................................. 0-500mA 903B-20 .......................0-20mA 903B-1A................................... 0-1A 903B-50 .......................0-50mA 903B-2A................................... 0-2A 903B-100 .....................0-100mA 903B-5A...................................0-5A OUTPUT VOLTAGE SIGNAL ........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY....................................................................... ±1% FS (±50mV) RIPPLE .............................................................................. 2% FS RMS max. IMPEDANCE ..................................................................... 1000 Ohms ±5%, 5mA to 1A range 500 Ohms ±5%, 2A 200 Ohms ±5%, 5A RESPONSE....................................................................... 50 m-sec. max. ( 10 to 90%) TEMPERATURE COEFFICIENT...................................... ±.04% FS/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................. 50mAdc max. REVERSE POLARITY PROTECTION ............................. 10µA current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -55°C to +85°C STORAGE TEMPERATURE RANGE.............................. -60°C to +100°C INSULATION RESISTANCE ............................................ 100 M-ohms (all terminals to case) DIELECTRIC STRENGTH................................................ 350V RMS (all terminals to case) ALTITUDE ......................................................................... Operating sea level to 60,000 ft. VIBRATION ....................................................................... Operating - 0.06 in. D.A., 10 to 55 Hz method 201 of MIL-STD-202 SHOCK.............................................................................. Operating 50 g, 11 m-sec half sine pulse method 213 Condition A of MIL-STD-202 MOISTURE RESISTANCE ............................................... Will meet method 106 of MIL-STD-202 and method 507.1 Proc. 1 of MIL-STD-810 OPERATING HUMIDITY................................................... 0% to 95% RH ATTITUDE......................................................................... Meets spec. for any mounting position RIPPLE .............................................................................. 40mV reflected onto pass-thru line WEIGHT ............................................................................ 1.25 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-903B M AACAAC
TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY AND SIGNAL (RTN) C. OUTPUT SIGNAL (+) D. SPARE E. SPARE F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT TRANSDUCER SERIES S767
PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S767-10 ...............................0 to 10mA S767-200 ........................... 0 to 200mA S767-20 ...............................0 to 20mA S767-250 ........................... 0 to 250mA S767-50 ...............................0 to 50mA S767-500 ........................... 0 to 500mA S767-100 .............................0 to 100mA S767-1A............................. 0 to 1A INPUT CURRENT RANGE.................................. See Table CURRENT OVERLOAD........................... 100Adc OUTPUT VOLTAGE SIGNAL .................................. 0 to +5Vdc FS (Full Scale) ACCURACY.............................................. ± 1% FS (±50mV) OUTPUT IMPEDANCE............................ 100 Ohms max. RIPPLE ..................................................... 1% FS (RMS) max. TEMPERATURE COEFFICIENT............. ±.02% FS/°C max. LONG TERM STABILITY......................... ±.2% FS/yr RESPONSE (10 TO 90%)........................ 50 m-sec max. PROTECTION.......................................... Continuous Short ckt Without damage POWER SUPPLY SUPPLY VOLTAGE ................................ 22Vdc to 36Vdc CURRENT DRAIN.................................... 12mAdc OVER VOLTAGE PROTECTION............ Terminals A & B ±36Vdc without damage REVERSE POLARITY PROTECTION .... 10µA max. current drain ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -40° to +85°C STORAGE TEMPERATURE ................... -55° to +85°C HUMIDITY ................................................ 0% to 95% RH MOISTURE RESISTANCE ...................... MIL-STD-810, Method 507.1, Proc. I ALTITUDE ................................................ Sea Level to 10 -5 torr (Hard Vacuum) PYROSHOCK (PROTO FLIGHT) ........... 100Hz @ 50g +6dB/Oct to 1100g @ 1KHz flat to 10KHz VIBRATION (SINE) .................................. 0.06 In. D.A., 10 to 55 Hz (RANDOM) ............................................... Overall 37.9g’s 20 to 50 Hz +12db/octave 0.084 to 3.0g2/Hz. 3.0 flat. 130 to 300 Hz -6db/octave 3.0 to .6g2/Hz. 300 to 1 flat 1500 to 2000 Hz -6db/octave 0.60 to 0.33g2/Hz. INSULATION RESISTANCE .................. 100 M-Ohms min. @ 100Vdc ATTITUDE................................................ Performs in any position. FINISH ...................................................... Fuse Tin Plate ENCAPSULANT....................................... Stycast 2850FT Cat 11 WEIGHT ................................................... .49lbs max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S767-903 C AAC
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY (RTN) C. OUTPUT SIGNAL (+) D. OUTPUT (RTN) E. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
DC CURRENT SENSOR SERIES 936
INPUT CURRENT INPUT CURRENT PART NO. AMPS DC PART NO. AMPS DC 936-10 ......................... 0 TO 10mA 936-250....................................0 TO 250mA 936-20 ......................... 0 TO 20mA 936-500................................... 0 TO 500mA 936-50 ......................... 0 TO 50mA 936-1A .................................... 0 TO 1A 936-100 ....................... 0 TO 100mA 936-2A .................................... 0 TO 2A 936-200 ....................... 0 TO 200mA 936-5A .....................................0 TO 5A INPUT CURRENT RANGE (Adc) ................................................ See Table TRANSIENT PROTECTION VOLTAGE OF THRU CABLE..................................... 35KV (with insulated cable) VOLTAGE TRANSIENT............................................. 500 Volts/u-sec CURRENT TRANSIENT ............................................ 500 Amps/u-sec REFLECTED RIPPLE (THRU CABLE)............................ 40mV OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY...................................................................... ±1% FS (±50mV) RESPONSE (10 TO 90%) ................................................ 100 m-sec. max. RIPPLE ............................................................................. 2% FS RMS max. TEMPERATURE COEFFICIENT..................................... ± 0.1% FS/°C max. OUTPUT IMPEDANCE (±5%).......................................... 1000 Ohms (Ranges 10mA to 1A) 500 Ohms (Range 2A) 200 Ohms (Range 5A) POWER SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................ 75mAdc max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -55°C to +85°C STORAGE TEMPERATURE RANGE ............................. -55°C to +100°C INSULATION RESISTANCE............................................ 100 K-Ohms WEIGHT ........................................................................... 28 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-936 H AAC
TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT (RTN) D. SPARE E. OUTPUT (+) F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT SENSOR SERIES S218
INPUT INPUT PART NO. CURRENT RANGE PART NO. CURRENT RANGE S218-100..................... 0 TO 100mA S218-1A...................................0 TO 1A S218-200..................... 0 TO 200mA S218-2A.................................. 0 TO 2A S218-500..................... 0 TO 500mA S218-5A.................................. 0 TO 5A OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY...................................................................... ±1% FS (±50mV) RIPPLE ............................................................................. 2% FS RMS max. IMPEDANCE..................................................................... 1000 Ohms ±5%, 100mA to 1A range 500 Ohms ±5%, 2A 200 Ohms ±5%, 5A RESPONSE...................................................................... 50 m-sec max. (10 to 90%) TEMPERATURE COEFFICIENT..................................... ± .04%/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................ 65mAdc max. REVERSE POLARITY PROTECTION ............................ 10µA max. Current Drain- no damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -55°C to +85°C STORAGE TEMPERATURE RANGE ............................. -60°C to +100°C INSULATION RESISTANCE............................................ 100 M-Ohms (terminals 1,2,3,&4 to case) DIELECTRIC STRENGTH ............................................... 350V RMS (terminals 1,2,3,&4 to case) ALTITUDE......................................................................... Operating sea level to 60,000 ft. VIBRATION....................................................................... Operating - 0.06 in. D.A., 10 to 55Hz Method 201 of MIL-STD-202. SHOCK ............................................................................. Operating 50g, 11 m-sec half sine pulse Method 213 Condition A of MIL-STD-202. MOISTURE RESISTANCE .............................................. Will meet Method 106 of MIL-STD-202 and Method 507.1 Proc. 1 of MIL-STD-810 OPERATING HUMIDITY.................................................. 0 to 95% RH ATTITUDE ........................................................................ Meets spec. for any mounting position. RIPPLE ............................................................................. 40mV reflected onto pass-thru line. WEIGHT ........................................................................... 1.5 lbs. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S218-903 G AACAAC
TERMINAL IDENTIFICATION
1. SUPPLY VOLTAGE (+) 2. SUPPLY VOLTAGE (RTN) 3. OUTPUT SIGNAL (RTN) 4. OUTPUT SIGNAL (+) 5. CASE GROUND
NOTE: MOLDED TERMINAL BARRIER WITH 5-40 TERMINAL SCREWS 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
DC CURRENT TRANSDUCER SERIES S619
PART CURRENT INPUT NUMBER RANGE OVERLOAD TRANSIENT IMPEDANCE S619-3.5 0 TO 3.5A 0 TO ±5A 250 5 S619-10 0 TO 10A 0 TO ±15A 750 1.75 INPUT CURRENT CURRENT RANGE .................................................................. See Table OVERLOAD.............................................................................. See Table continuous TRANSIENT OVERLOAD........................................................ See Table sec / hr max. ISOLATION............................................................................... 500V RMS, 60Hz 1 min. INPUT IMPEDANCE................................................................. See Table milli-Ohms max.
OUTPUT VOLTAGE SIGNAL................................................................... 0 to +3.5Vdc FS (Full Scale) ACCURACY (@ 25°C).............................................................. ± 2% FS (± 70mV) RESPONSE (0 to 90%) ............................................................ 1 m-sec OUTPUT IMPEDANCE ............................................................ 50 Ohms max. TEMPERATURE COEFFICIENT............................................. .04% FS /°C max. LOAD IMPEDANCE.................................................................. 10K-Ohms min. POWER SUPPLY (PS) SUPPLY VOLTAGE ................................................................. +5Vdc ± .5Vdc CURRENT DRAIN.................................................................... 5mAdc max. POWER SUPPLY PROTECTION............................................ 0 to +12Vdc withstanding without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.................................. -55° to +85°C STORAGE TEMPERATURE RANGE ..................................... -55° to +105°C OPERATING HUMIDITY.......................................................... 0% to 95% RH MOISTURE RESISTANCE ...................................................... Will meet Method 106 of MIL-STD-202 & Method 507.1, Procedure I of MIL-STD-810 PRESSURE .............................................................................. 1 X 10-8 torr. SHOCK ..................................................................................... Operating: 50g, 11 m-sec half sine pulse (Method 213, Condition A of MIL-STD-202) VIBRATION .............................................................................. MIL-STD-202F Method 214 Test Condition G 26.4 GRMS overall DIELECTRIC STRENGTH ....................................................... 350V RMS dielectric withstanding voltage (Method 301 of MIL-STD-202) INSULATION RESISTANCE.................................................... 10 M-ohms min. (Method 302, Condition A of MIL-STD-202) ATTITUDE ................................................................................ Unit will perform as specified when mounted in any position. ENCAPSULANT ...................................................................... Stycast 2850FT Cat 11 CASE ........................................................................................ Diallylpthlalate MIL-M-14F,SDG WEIGHT ................................................................................... 1 oz. Typ.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S619 J AAC NOTE: APPLY RTV 133 ADHESIVE (OR EQUIVALENT) 360° AROUND BOTTOM OF UNIT AFTER INSTALLING TO MEET ENVIRONMENTAL CHARACTERISTICS.
TERMINAL IDENTIFICATION 1. INPUT CURRENT (+) 2. INPUT CURRENT (-) 3. SUPPLY VOLTAGE (+) 4. SUPPLY VOLTAGE (RTN) 5. OUTPUT SIGNAL (RTN) 6. OUTPUT SIGNAL (+)
NOTE: TERMINALS 4 & 5 ARE ELECTRICALLY COMMON.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
DC CURRENT SENSOR SERIES 950
INPUT CURRENT MODEL NUMBER RANGE (AMPS DC) 950-10 ........................................................ 0 - 10 950-20 ........................................................ 0 - 20 950-30 ........................................................ 0 - 30 950-40 ........................................................ 0 - 40 950-50 ........................................................ 0 - 50 OUTPUT VOLTAGE SIGNAL ........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY....................................................................... ±0.5% FS (±25mV) for 20,30,40, & 50A models ±1% FS (±50mV) for 10A model RESPONSE (10 TO 90%)................................................. 10 m-sec. max. RIPPLE .............................................................................. 25mV (RMS) max. TEMPERATURE COEFFICIENT...................................... ±.02% FS/°C LONG TERM STABILITY.................................................. ±0.1% FS/yr OUTPUT IMPEDANCE..................................................... 4000 ohms max. OUTPUT PROTECTION .................................................. Output terminals E & C will withstand ±250Vdc for 10m-sec, ±60Vdc continuously, short circuit POWER SUPPLY (PS) SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................. 70mAdc max. OVER VOLTAGE PROTECTION..................................... Terminals A & B withstand ±35Vdc without damage REVERSE POLARITY PROTECTION ............................. 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -25° to +85°C STORAGE TEMPERATURE RANGE.............................. -55° to +85°C DIELECTRIC STRENGTH................................................ 350 V RMS dielectric withstanding voltage (method 301 of MIL-STD-202) INSULATION RESISTANCE ............................................ 10 M-ohms min. (method 302, Condition A of MIL-STD-202) ALTITUDE ......................................................................... Operating: sea level to 60,00 ft. Non-operating: sea level to 120,000 ft. (method 105, Condition A of MIL-STD-202) VIBRATION ....................................................................... Operating: 0.06 inch D.A., 10 to 55 Hz (method 201 of MIL-STD-202) SHOCK.............................................................................. Operating: 50g, 11 m-sec half sine pulse (method 213, Condition A of MIL-STD-202) MOISTURE RESISTANCE ............................................... Will meet method 106 of MIL-STD-202 and Method 507.1, Procedure I of MIL-STD-810 OPERATING HUMIDITY................................................... 0% to 95% RH ATTITUDE......................................................................... Unit will perform as specified when mounted in any position
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-950 F AAC
TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT (RTN) D. SPARE E. OUTPUT (+) F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(6316) 694-5100 Fax:(631) 694-6739
DC CURRENT SENSOR SERIES 913B
INPUT INPUT PART NO. CURRENT RANGE PART NO. CURRENT RANGE 913B-10....................... 0 TO 10A 913B-35 ...................................0 TO 35A 913B-15....................... 0 TO 15A 913B-40 .................................. 0 TO 40A 913B-20....................... 0 TO 20A 913B-50 .................................. 0 TO 50A 913B-25....................... 0 TO 25A 913B-75 .................................. 0 TO 75A 913B-30....................... 0 TO 30A 913B-100 ................................ 0 TO 100A INPUT CURRENT RANGE ............................................................................. See Table OVER CURRENT (UNLIMITED)...................................... Nondestructive/nonlatching Saturated Output OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY...................................................................... ±1% FS RESPONSE ( 10 TO 90%) ............................................... 1 m-sec. max. IMPEDANCE..................................................................... 100Ω max. for 10A to 50A ranges 275Ω for 75A to 100A ranges RIPPLE ............................................................................. 10mV RMS max. TEMPERATURE COEFFICIENT..................................... ±0.02% FS/°C max. OUTPUT PROTECTION.................................................. Terminals D & E will withstand ±32Vdc or short circuit POWER SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................ 75mA max. REVERSE POLARITY PROTECTION ............................ 10µA max. Current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -55°C to +85°C STORAGE TEMPERATURE RANGE ............................. -55°C to +100°C DIELECTRIC STRENGTH ............................................... 350V RMS MIL-STD-202 Method 301 INSULATION RESISTANCE............................................ 200 M-ohms min. MIL-STD-202 Method 302 Test Condition A ALTITUDE......................................................................... Operating sea level to 100,000 ft., MIL-STD-202, Method 105, Condition D VIBRATION....................................................................... Operating 0.06 in. D.A., 10Hz to 55 Hz MIL-STD-202 Method 201 SHOCK ............................................................................. Operating 50 g, 11 m-sec MIL-STD-202 Method 213, Condition A MOISTURE RESISTANCE .............................................. MIL-STD-202 Method 106 OPERATING HUMIDITY.................................................. 0% to 95% RH ATTITUDE ........................................................................ Meets spec. for any mounting position WEIGHT ........................................................................... 12 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-913B J AACAAC
TERMINAL IDENTIFICATION
A. SPARE B. SPARE C. +28Vdc D. D.C. COMMON E. 0 TO +5V OUTPUT F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
TERMINAL IDENTIFICATION
A. SPARE B. SUPPLY VOLTAGE (RTN) C. SUPPLY VOLTAGE (+) D. OUTPUT SIGNAL (RTN) E. OUTPUT SIGNAL (+) F. CASE GROUND TERMINALS B & D ARE COMMON
DC CURRENT TRANSDUCER SERIES 913A
PART NO. INPUT CURRENT PART NO. INPUT CURRENT 913A-10....................... 0 to 10A 913A-40 ...................................0 to 40A 913A-20....................... 0 to 20A 913A-50 .................................. 0 to 50A 913A-25....................... 0 to 25A 913A-75 .................................. 0 to 75A 913A-30....................... 0 to 30A 913A-100 ................................ 0 to 100A INPUT RANGE ............................................................................. See Table OVER CURRENT (UNLIMITED)...................................... Nondestructive/nonlatching Saturated Output OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY...................................................................... ±1% FS RESPONSE(10 TO 90%) ................................................. 1 m-sec max. IMPEDANCE..................................................................... 100Ω for 10A to 50A ranges 1000Ω for 75A to 100A ranges RIPPLE ............................................................................. 10mV RMS max. TEMPERATURE COEFFICIENT..................................... ±0.02% FS/°C max. for 10A & 50a RANGES ±0.04% for 75A & 100A ranges OUTPUT PROTECTION.................................................. Terminals D & E will withstand +32Vdc or short circuit POWER SUPPLY SUPPLY VOLTAGE ......................................................... +28Vdc ±4Vdc CURRENT DRAIN............................................................ 75mA max. REVERSE POLARITY PROTECTION ............................ 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -55°C to +85°C STORAGE TEMPERATURE RANGE ............................. -55°C to +100°C DIELECTRIC STRENGTH ............................................... 350V RMS MIL-STD-202 Method 301 INSULATION RESISTANCE............................................ 200M-Ohms min. MIL-STD-202 Method 302 Test Condition A ALTITUDE......................................................................... Operating sea level to 100,000 ft. MIL-STD-202, Method 105, Condition D VIBRATION....................................................................... Operating 0.06 in D.A., 10Hz to 55Hz MIL-STD- 202, Method 201 SHOCK ............................................................................. Operating 50g 11 m-sec MIL-STD-202, Method 213, Condition A MOISTURE RESISTANCE .............................................. MIL-STD-202, Method 106 OPERATING HUMIDITY.................................................. 0 to 95% RH ATTITUDE ........................................................................ Meets specification for any mounting position WEIGHT ........................................................................... 9 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-913A T AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT TRANSDUCER SERIES S770 PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S770-20 .........................0 to 20 S770-50…………………0 to 50 S770-25 .........................0 to 25 S770-60…………………0 to 60 S770-30 .........................0 to 30 S770-70…………………0 to 70 S770-40 .........................0 to 40 S770-100……………….0 to 100 INPUT RANGE.............................................................................. See Table OVERLOAD CONTINUOUS............................................. ±2000Adc FREQUENCY RANGE...................................................... DC to 350Hz OUTPUT VOLTAGE SIGNAL ........................................................... 0 to+5Vdc ACCURACY....................................................................... ±1% FS RESPONSE (10 to 90%) ................................................... 1 m sec. OUTPUT IMPEDANCE..................................................... 10 Ohms LOAD RESISTANCE ........................................................ 10k Ohms min TEMPERATURE COEFFICIENT...................................... ±.02%FS per °c max. OUTPUT PROTECTION .................................................. Short Circuit POWER SUPPLY SUPPLY VOLTAGE ......................................................... +12Vdc to +36Vdc CURRENT DRAIN............................................................. 10mAdc max. PROTECTION................................................................... Reverse polarity protected TRANSIENT PROTECTION............................................. ±60V (T<5mS) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -40° to +85°C STORAGE TEMPERATURE RANGE.............................. -40° to +85°C ISOLATION ....................................................................... Input to output 5KV rms 60Hz/1min. INSULATION RESISTANCE ............................................ 500 M-Ohms @ 500Vdc CASE MATERIAL.............................................................. Molded Plastic meets UL flammability rating 94V-O WEIGHT ........................................................................... 10 oz. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S770 C AAC
TERMINAL IDENTIFICATION 1. SUPPLY VOLTAGE (+) 2. SUPPLY (RTN) 3. OUTPUT (RTN) 4. OUTPUT SIGNAL (+)
TERMINAL SCREWS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32 WIDE.
DC CURRENT TRANSDUCER SERIES 920 4 TO 20 mA 2 WIRE LOOP POWER CLAMP ON CURRENT PART NO RANGE ACCURACY 920-50 0 TO 50Adc 1.25% 920-75 0 TO 75Adc 1.0% 920-100 0 TO 100Adc 1.0% 920-125 0 TO 125Adc 1.0% INPUT RANGE ........................................................................... See table OVERLOAD CONTINUOUS........................................... ±5000Adc FREQUENCY RANGE.................................................... DC to 35Hz OUTPUT CURRENT SIGNAL ........................................................ 4 to 20mAdc ACCURACY (Over Temperature Range) ...................... See table & Note 1 %FS (Full Scale) RESPONSE (10 to 90%) ................................................ 10 m sec. LOAD RESISTANCE (RL) .............................................. 250 Ohms Nominal LOAD RESISTANCE RANGE ....................................... 0 to 300 Ohms CURRENT SIGNAL @ OVERLOAD............................... 24 mAdc typ. PROTECTION ................................................................ Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE ....................................................... +24Vdc Nominal CURRENT DRAIN .......................................................... 4 to 24mAdc SUPPLY VOLTAGE RANGE .......................................... +18 to 28Vdc TRANSIENT PROTECTION ........................................... ±40V (T<5mS) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE......................... -40° to +85°C STORAGE TEMPERATURE RANGE ............................ -45° to +85°C ISOLATION..................................................................... Input to output 2KV rms 60Hz/1min. INSULATION RESISTANCE .......................................... 500 M-Ohms @ 500Vdc CASE MATERIAL ........................................................... Molded Plastic meets UL flammability rating 94V-O WEIGHT ......................................................................... 14 oz. Max. FINISH ............................................................................ Blue Textured Pantone No. 294C NOTE 1: Specified accuracy includes the combined worst case effects of Zero Offset, Temperature, Hysteresis, Supply Swings and Current Cable Positioning. 2: Insert tool and press to release. (Recommended Tool : Screwdriver, 3/16 standard tipped)
Dimensions in Inches, Tolerances: .XX ± .06 .XXX ± .030
Drawing Number Rev.
700-920 A AAC
TERMINAL IDENTIFICATION PIN 1 : POWER PIN 2 : RTN PIN 3 : N.C. PIN 4 : N.C. PIN 5 : N.C.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT TRANSDUCERDC CURRENT TRANSDUCER SPLITSPLIT CORE CORE
PART. NO.PART. NO. SELECTABLE MEAS. RANGESELECTABLE MEAS. RANGE OUTPUT SIGNALOUTPUT SIGNAL DCT-05-100 50, 75, 100A 0-5VDC DCT-05-200 100, 150, 200A 0-5VDC DCT-05-300 150, 225, 300A 0-5VDC DCT-05-400 200, 300, 400A 0-5VDC DCT-20-100 50, 75, 100A 4-20mA DCT-20-200 100, 150, 200A 4-20mA DCT-20-300 150, 225, 300A 4-20mA DCT-20-400 200, 300, 400A 4-20mA
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--DCTDCT BB AACAAC
SPECIFICATIONSSPECIFICATIONS Output SignalOutput Signal 4-20mA or 0-5VDC OutOutput Limitput Limit 4-20mA: 44mA 0-5vdc: : 13VDC AccuracyAccuracy 1.0% FS RepeatabilityRepeatability 1.0%FS Response TimeResponse Time 100mS (to 90% of step change) Frequency RangeFrequency Range DC Power SupplyPower Supply 20-50VDC, 22-38VAC power input and output signal are not isolated. Power ConsumptionPower Consumption 2VA LoadingLoading 4-20mA: : 650Ω max. 0-5VDC: 250KΩ for rated accuracy; 25KΩ, add 1% error. Isolation VoltageIsolation Voltage 3KV (monitored line output) LinearityLinearity 0.75% FS Current RangesCurrent Ranges Field selectable ranges from 0-400A. Sensing ApertureSensing Aperture 0.85” (21.5mm) sq. CaseCase UL 94V-0 Flammability rated EnvironmentalEnvironmental -4 to 122° F (-20 to 50° C), 0-95% RH, non-condensing
DCT-
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT TRANSDUCER SERIES S728B AAC INPUT OUTPUT ACCURACY SUPPLY PART CURRENT (SEE NOTE 1) CURRENT NUMBER RANGE @25°C 0 to 70°C -55to85°C DRAIN S728B-50 0 to 50Adc ±0.5% ±0.8% ±1.5% 40mA S728B-100 0 to 100Adc ±0.5% ±0.6% ±1.0% 40mA S728B-150 0 to 150Adc ±0.5% ±0.6% ±1.0% 50mA S728B-200 0 to 200Adc ±0.5% ±0.6% ±0.8% 50mA S728B-250 0 to 250Adc ±0.5% ±0.6% ±0.8% 65mA S728B-300 0 to 300Adc ±0.4% ±0.5% ±0.8% 80mA S728B-400 0 to 400Adc ±0.3% ±0.4% ±0.6% 110mA INPUT CURRENT RANGE .................................................... See Table CURRENT OVERLOAD.......................... 5000Adc Continuous (Nonlatching/Saturated Output) OUTPUT CURRENT SIGNAL................................. 0 to 5Vdc FS (Full Scale) ACCURACY............................................. % FS See Table & Note 1 LINEARITY............................................... ±0.1% FS. BANDWIDTH........................................... DC TO 350KHZ RESPONSE TIME ( 10 to 90%)............... 1 u-sec. OUTPUT IMPEDANCE ........................... 50 Ohms max. POWER SUPPLY SUPPLY VOLTAGE ................................ 28Vdc ±4Vdc CURRENT DRAIN................................... See Table REVERSE POLARITY PROTECTION ... 100uA Current Drain Without Damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE............... -55 to +85°C STORAGE TEMPERATURE .................. -55 to +90°C OPERATING HUMIDITY......................... 0% to 95% RH MOISTURE RESISTANCE .................... Will meet Method 106 of MIL-STD-202 & Method 507.1, Proc. 1 of MIL-STD-810 ALTITUDE ............................................... Operating sea level to 60,000 ft. Non-operating - sea level to 120,000 ft. (Method 105, Condition A of MIL-STD-202) SHOCK ................................................... Non-Operating - 50g, 11 m-sec half sine pulse (Method 213 Condition A of MIL-STD-202) RANDOM VIBRATION ............................ Operating MIL-STD-810E Cat.5, Proc.1, WO=0.012G2/HZ, Duration 1 hr., Figure 514.4-8 Suggested Vibration Levels for High Performance Aircraft 12.5G-RMS Min. DIELECTRIC STRENGTH ..................... 350V RMS Terminals A-D to E & Case INSULATION RESISTANCE .................. 100 M-Ohms Min. FINISH .................................................... Fuse Tin Plate ALTITUDE................................................ Unit will perform as specified when mounted in any position WEIGHT ................................................. 0.57 lbs. max.
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT SIGNAL (RTN) D. OUTPUT SIGNAL (+) E. CASE GROUND
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S728B-952 A AAC NOTE: Specified accuracy includes the combined worst case effects of Zero Offset, Hysteresis, Supply Swings and Current Cable Positioning
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT TRANSDUCER SERIES 952
AAC INPUT OUTPUT ACCURACY OUTPUT SUPPLY PART CURRENT (SEE NOTE 1) IMPEDANCE CURRENT NUMBER RANGE @25°C 0 to 70°C -55to85°C OHMS DRAIN 952-50 0 to 50Adc ±0.5% ±0.8% ±1.5% 100 40mA 952-100 0 to 100Adc ±0.5% ±0.6% ±1.0% 100 40mA 952-150 0 to 150Adc ±0.5% ±0.6% ±1.0% 70 60mA 952-200 0 to 200Adc ±0.5% ±0.6% ±0.8% 50 65mA 952-250 0 to 250Adc ±0.5% ±0.6% ±0.8% 40 80mA 952-300 0 to 300Adc ±0.4% ±0.5% ±0.8% 33 100mA 952-400 0 to 400Adc ±0.3% ±0.4% ±0.6% 50 75mA 952-500 0 to 500Adc ±0.3% ±0.4% ±0.6% 40 100mA 952-600 0 to 600Adc ±0.3% ±0.4% ±0.6% 33 140mA 952-750 0 to 750Adc ±0.3% ±0.4% ±0.6% 26 185mA INPUT CURRENT RANGE .................................................... See Table CURRENT OVERLOAD.......................... 5000 Adc Continuous ( Nonlatching/Saturated Output) OUTPUT VOLTAGE SIGNAL.................................. 0 to +5 Vdc FS (Full Scale) ACCURACY............................................. % FS See Table & Note 1 LINEARITY............................................... ±0.1% FS DI/DT ACCURATELY FOLLOWED ........ 100 A/u-sec. BANDWIDTH........................................... DC TO 100KHZ RESPONSE TIME ................................... <1 u-sec. OUTPUT IMPEDANCE ........................... See Table POWER SUPPLY SUPPLY VOLTAGE ................................ 28Vdc ±4Vdc CURRENT DRAIN................................... See Table REVERSE POLARITY PROTECTION ... 10uA Current Drain Without Damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE............... -55 to +85°C STORAGE TEMPERATURE .................. -55 to +85°C OPERATING HUMIDITY......................... 0% to 95% RH MOISTURE RESISTANCE .................... Will meet Method 106 of MIL-STD-202 & Method 507.1, Proc. 1 of MIL-STD-810 ALTITUDE ............................................... Operating sea level to 60,000 ft. Non-operating - sea level to 120,000 ft. (Method 105, Condition A of MIL-STD-202) SHOCK ................................................... Non-Operating - 50g, 11 m-sec half sine pulse (Method 213 Condition A of MIL-STD-202) RANDOM VIBRATION ............................ Operating MIL-STD-810E Cat.5, Proc.1, WO=0.012G2/HZ, Duration 1 hr., Figure 514.4-8 Suggested Vibration Levels for High Performance Aircraft 12.5G-RMS Min. DIELECTRIC STRENGTH ..................... 350V RMS Terminals 1-5 to 6 & Case INSULATION RESISTANCE .................. 100 M-Ohms Min. ALTITUDE................................................ Unit will perform as specified when mounted in any position WEIGHT ................................................. 1.21 lbs. max.
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT SIGNAL (RTN) D. SPARE E. OUTPUT SIGNAL (+) F. CASE GROUND
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-952 K AAC NOTE: Specified accuracy includes the combined worst case effects of Zero Offset, Hysteresis, Supply Swings and Current Cable Positioning
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT TRANSDUCER SERIES S347
REMOVABLE YOKE TYPE
INPUT INPUT PART NO. CURRENT RANGE PART NO. CURRENT RANGE S347-100..................... 0 TO 100A S347-500 .................................0 TO 500A S347-150..................... 0 TO 150A S347-750 ................................ 0 TO 750A S347-200..................... 0 TO 200A S347-1000 .............................. 0 TO 1000A S347-225..................... 0 TO 225A S347-1500 .............................. 0 TO 1500A S347-250..................... 0 TO 250A S347-2000 ...............................0 TO 2000A S347-300..................... 0 TO 300A S347-2500 ...............................0 TO 2500A S347-5000 ...............................0 TO 5000A INPUT CURRENT RANGE .......................................................... 0 to Full Scale (FS) See Table CURRENT OVERLOAD................................................... 100 times FS OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc (FS) ACCURACY...................................................................... ±1% FS (±50mV) RESPONSE...................................................................... 200 µ-sec. max. TEMPERATURE COEFFICIENT..................................... ± .05% FS/°C OUTPUT IMPEDANCE .................................................... 100 Ohms max. SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc SUPPLY BURDEN............................................................ 100mA max. PROTECTION .................................................................. Reverse Polarity Protection ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -25°C to +75°C STORAGE TEMPERATURE RANGE ............................. -55°C to +85°C ISOLATION....................................................................... Input/Output/Case (Supply & Output common) CASE MATERIAL ............................................................. Aluminum Casting FINISH .............................................................................. Black Anodize Finish WEIGHT ........................................................................... 18 oz.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S347-909 C AACAAC
TERMINAL IDENTIFICATION
CONNECTOR BARRIER A SIGNAL OUTPUT (+) 1 B OUTPUT (RTN) 2 C SUPPLY VOLTAGE (+) 3 D SUPPLY VOLTAGE (RTN) 4 E SPARE F SPARE
NOTES: 1. SERIES S347-909 NORMALLY SUPPLIED WITH 4 TERMINAL BARRIER STRIP AVAILABLE WITH 6 PIN OPTIONAL CONNECTOR MS3112E-10-6P OR EQUIVALENT. ADD LETTER -C AFTER PART NUMBER FOR CONNECTOR OPTION. (REFERENCE: CONNECTOR MATES WITH PT06A-10-6S (SR) OR EQUIVALENT.
MOLDED TERMINAL BARRIER WITH 5-40 TERMINAL SCREWS AND .375 CENTER DISTANCES. TERMINALS ACCEPT WIRE SIZE UP TO #16 AWG. WITH LUGS TO .281 IN. WIDE.
DC CURRENT TRANSDUCER SERIES 921 4 TO 20 mA 2 WIRE LOOP POWER CLAMP ON CURRENT PART NO RANGE ACCURACY 921-200 0 TO 200Adc 1.5% 921-250 0 TO 250Adc 1.5% 921-300 0 TO 300Adc 1.5% 921-400 0 TO 400Adc 1.0% 921-500 0 TO 500Adc 1.0% 921-750 0 TO 750Adc 1.0%
921-1000 0 TO 1000Adc 1.0% 921-1500 0 TO 1500Adc 1.0% 921-2000 0 TO 2000Adc 1.0%
INPUT RANGE ........................................................................... See table OVERLOAD CONTINUOUS........................................... ±5000Adc FREQUENCY RANGE.................................................... DC to 35Hz OUTPUT CURRENT SIGNAL ........................................................ 4 to 20mAdc ACCURACY (Over Temperature Range) ...................... See table & Note 1 %FS (Full Scale) RESPONSE (10 to 90%) ................................................ 10 m sec. LOAD RESISTANCE (RL) .............................................. 250 Ohms Nominal LOAD RESISTANCE RANGE ....................................... 0 to 300 Ohms CURRENT SIGNAL @ OVERLOAD............................... 24 mAdc typ. PROTECTION ................................................................ Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE ....................................................... +24Vdc Nominal CURRENT DRAIN .......................................................... 4 to 24mAdc SUPPLY VOLTAGE RANGE .......................................... +18 to 28Vdc TRANSIENT PROTECTION ........................................... ±40V (T<5mS) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE......................... -40° to +85°C STORAGE TEMPERATURE RANGE ............................ -45° to +85°C ISOLATION..................................................................... Input to output 2KV RMS 60Hz/1min. INSULATION RESISTANCE .......................................... 500 M-Ohms @ 500Vdc CASE MATERIAL ........................................................... Molded Plastic meets UL flammability rating 94V-O WEIGHT ......................................................................... 14 oz. Max. FINISH ............................................................................ Blue Textured Pantone No. 294C NOTE 1: Specified accuracy includes the combined worst case effects of Zero Offset, Temperature, Hysteresis, Supply Swings and Current Cable Positioning. 2: Insert tool and press to release. (Recommended Tool : Screwdriver, 3/16 standard tipped)
Dimensions in Inches, Tolerances: .XX ± .06 .XXX ± .030
Drawing Number Rev.
700-921 B AAC
TERMINAL IDENTIFICATION PIN 1 : POWER PIN 2 : RTN PIN 3 : N.C. PIN 4 : N.C PIN 5: N.C.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT SENSOR SERIES S444
REMOVABLE YOKE TYPE
INPUT INPUT PART NO. CURRENT RANGE PART NO. CURRENT RANGE S444-200 .....................0 TO 200 S444-750 ................................. 0 TO 750 S444-225 .....................0 TO 225 S444-1000 ............................... 0 TO 1000 S444-250 .....................0 TO 250 S444-1500 ............................... 0 TO 1500 S444-300 .....................0 TO 300 S444-2000 ............................... 0 TO 2000 S444-500 .....................0 TO 500 S444-2500 ............................... 0 TO 2500 INPUT CURRENT RANGE........................................................... See Table CURRENT OVERLOAD.................................................... Unlimited Nondestructive OUTPUT VOLTAGE SIGNAL ........................................................... 0 to +5Vdc FS (Full Scale) ACCURACY....................................................................... ±1% FS (±50mV) RESPONSE (10 TO 90%)................................................. 200 u-sec. max. OUTPUT IMPEDANCE..................................................... 100 Ohms max. TEMPERATURE COEFFICIENT...................................... ± .05% FS/°C max. SHORT CIRCUIT DURATION.......................................... Continuous OUTPUT LOAD................................................................. 1 K-Ohms min. SUPPLY SUPPLY VOLTAGE ......................................................... 28Vdc ±4Vdc CURRENT DRAIN............................................................. 100mA max. REVERSE POLARITY ...................................................... No damage, 10µA current drain max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -25°C to +75°C STORAGE TEMPERATURE RANGE.............................. -55°C to +85°C ISOLATION ....................................................................... Input/Output/Case (Supply & Output common) CASE MATERIAL.............................................................. GE Lexan (Molded plastic) meets UL flammability rating 94V-0 WEIGHT ............................................................................ 12 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S444-909 C AACAAC
TERMINAL IDENTIFICATION
CONNECTOR BARRIER A OUTPUT (+) 1 B OUTPUT (RTN) 2 C SUPPLY VOLTAGE (+) 3 D SUPPLY VOLTAGE (RTN) 4 E SPARE 5 F SPARE
NOTES: 1. NORMALLY SUPPLIED WITH 5 PIN TERMINAL BARRIER STRIP. MOLDED TERMINAL
BLOCK WITH 6-32 TERMINAL SCREWS, .325 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 16 AWG AND WIRE LUGS TO .250 IN. WIDE. AVAILABLE WITH 6 PIN OPTIONAL CONNECTOR MS3112E-10-6P OR EQUIVALENT. ADD LETTER -C AFTER PART NUMBER FOR CONNECTOR OPTION.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
TERMINAL IDENTIFICATION
BARRIER CONNECTOR 1 OUTPUT (+) A 2 OUTPUT (RTN) B 3 SUPPLY VOLTAGE (+) C 4 SUPPLY VOLTAGE (RTN) D 5 SPARE E SPARE F
DC CURRENT TRANSDUCER SERIES S465
REMOVABLE YOKE TYPE PART NO. INPUT RANGE PART NO. INPUT RANGE S465-150.............. 0 to 150Adc S465-1000 .............................. 0 to 1000Adc S465-250.............. 0 to 250Adc S465-1500 .............................. 0 to 1500Adc S465-500.............. 0 to 500Adc S465-2000 .............................. 0 to 2000Adc S465-750.............. 0 to 750Adc S465-2500 .............................. 0 to 2500Adc INPUT RANGE .................................................... Adc See Table OVERLOAD CONTINUOUS ................... Unlimited (Nondestructive Nonlatching/ Saturated Output) OUTPUT CURRENT SIGNAL................................. 4 to 20mAdc FS (Full Scale) ACCURACY............................................. ± 1% FS or ±0.2mA max. TEMPERATURE COEFFICIENT............ ± 0.05% FS / °C max. RESPONSE (10 to 90%) ......................... 200uS max. LOAD RESISTANCE .............................. 250 Ohms Nominal LOAD RESISTANCE RANGE................. 0 to 300 Ohms CURRENT SIGNAL @ OVERLOAD....... 30mA TYP. POWER SUPPLY (PS) SUPPLY VOLTAGE ................................ 16 to 26Vdc CURRENT DRAIN................................... 30mA plus I load PROTECTION ......................................... Reverse Polarity Protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -25° to +75°C STORAGE TEMPERATURE RANGE .... -40° to +85°C ISOLATION.............................................. Input/Output/Case INSULATION RESISTANCE................... 200 M-Ohms @ 500Vdc INPUT CONDUCTOR VOLTAGE........... 1.5KV max. (5KV max. with insulated cable) CASE ...................................................... Molded Plastic (GE Lexan) Meets UL Flammability Rating 94 WEIGHT ................................................. 18 oz. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S465-909 F AACAAC
NOTE: HOUSING AND POT HOLES SEALED MAKING TRANSDUCER WATER SPRAY RESISTANT. END USER MUST COAT TERMINAL BLOCK WITH SILICONE TO PREVENT CORROSION.
NOTE: 1. NORMALLY SUPPLIED WITH 5 PIN TERMINAL BARRIER STRIP. MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS, .325 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 16AWG AND WIRE LUGS TO .250 IN. WIDE. AVALIABLE WITH 6 PIN OPTIONAL CONNECTOR MS3112E-10-6P OR EQUIVALENT. ADD LETTER C AFTER PART NUMBER FOR CONNECTOR OPTION.
Code Ident. No. 15948 AAAACC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--S646S646 GG AACAAC
NOTE:NOTE: 1. SUPPLIED WITH 5 PIN TERMINAL BARRIER STRIP. MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS AND INT. TOOTH LOCKWASHERS, .325 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 16AWG AND WIRE LUGS TO .250 IN. WIDE.
TERMINAL IDENTIFICATIONTERMINAL IDENTIFICATION 1. OUTPUT (+) 2. OUTPUT (RTN) 3. SUPPLY VOLTAGE (+15V) 4. SUPPLY VOLTAGE (RTN) 5. SPARE
DC CURRENT TRANSDUCERDC CURRENT TRANSDUCER PART NUMBER S646PART NUMBER S646--10001000
INPUTINPUT RANGE NOMINAL ..................................................................... 0 to 1000Adc Full Scale OVERLOAD................................................................................ 0 to 5000Adc VOLTAGE................................................................................... 2500Vdc OUTPUTOUTPUT VOLTAGE SIGNAL .................................................................... 0 to +6Vdc SCALE FACTOR ........................................................................ 6mV per Amp ACCURACY................................................................................ ±2% FS (±20Adc) over temperature range RESPONSE TIME....................................................................... 200 µ-sec. max. OUTPUT IMPEDANCE............................................................... 15Ω Max. LOAD .......................................................................................... 50K to ∞∞ SHORT CIRCUIT ........................................................................ Protected TRANSIENT PROTECTION ...................................................... t ≤ 1ms ±200V POWER SUPPLYPOWER SUPPLY SUPPLY VOLTAGE ................................................................... +15Vdc (±0.4Vdc) with source impedance 0 to 50 Ohms POWER CONSUMPTION .......................................................... 0.5 W max. PROTECTION............................................................................. Reverse Polarity Protected TRANSIENT PROTECTION ....................................................... t ≤≤ 100ms +60V/-50V ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE.................................................. -30° C to +60°C STORAGE TEMPERATURE...................................................... -55°C to +85°C SHOCK........................................................................................ Operating 50g 11m-sec MIL-STD-202 Method 213 Condition A VIBRATION................................................................................. Operating 0.06 inch D.A. 10Hz to 55Hz MIL-STD-202 Method 201 HUMIDITY................................................................................... 0 to 95% RH Operating INSULATION RESISTANCE ...................................................... 500 M-Ohms @ 500Vdc DIELECTRIC STRENGTH.......................................................... 2500 DC ATTITUDE................................................................................... Performs in any position CASE MATERIAL....................................................................... Molded plastic (GE LEXAN) meets UL Flammability rating 94V-0 ENCAPSULANT ......................................................................... STYCAST 2850FT CAT 24LV WEIGHT ...................................................................................... 12 oz. max.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
* NOTE: FOR BARRIER OPTION ONLY, TERMINALS “A-E” AS SHOWN. OUTPUT A (RTN) AND OUTPUT B (RTN) ARE COMMON AT TERMINAL D.
DC CURRENT LEVEL DETECTOR SERIES 901B
PART NO. INPUT CURRENT PART NO. INPUT CURRENT 901B-20 .......................0 to 20mA 901B-500 ................................. 0 to 500mA 901B-50 .......................0 to 50mA 901B-1A................................... 0 to 1A 901B-100 .....................0 to 100mA 901B-2A................................... 0 to 2A 901B-200 .....................0 to 200mA 901B-5A................................... 0 to 5A 901B-250 .....................0 to 250mA INPUT CURRENT RANGE (Adc) ................................................. See Table TRANSIENT PROTECTION VOLTAGE OF THRU CABLE ...........................................30KV (with insulated cable) VOLTAGE TRANSIENT.................................................... 500 Volts/u-sec. CURRENT TRANSIENT................................................... 250 Amps/u-sec. CURRENT CAPABILITY................................................... 250 Amps for 100 m-sec. OUTPUT “A” VOLTAGE SIGNAL ........................................................... 0 to +5Vdc FS (Full Scale) LOAD ................................................................................. 5K Ω ±1% ACCURACY....................................................................... ±1% FS (±50mV) RIPPLE .............................................................................. 3% FS RMS max. RESPONSE (10 TO 90%)................................................. 50 m-sec. max. TEMPERATURE COEFFICIENT...................................... ±0.1% FS/°C max. OUTPUT “B” VOLTAGE SIGNAL ........................................................... 18Vdc @ 10mA (Above set point) <0.05Vdc (Below set point) SET POINT........................................................................ Adjustable from 70% FS to 110% FS SET POINT REPEATABILITY .......................................... ±2% FS RESPONSE TIME............................................................. 50 m-sec max. POWER SUPPLY (PS) SUPPLY VOLTAGE ......................................................... 24Vdc ±3Vdc CURRENT DRAIN............................................................. 75mA max. REVERSE POLARITY PROTECTION ............................. 10µA current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -20°C to +70°C STORAGE TEMPERATURE RANGE.............................. -55°C to +85°C INSULATION RESISTANCE ............................................ 100 K-ohms (all terminals to case) RIPPLE .............................................................................. 40mV reflected onto pass-thru line WEIGHT ............................................................................ 1.75 lbs. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-901B G AACAAC
TERMINAL IDENTIFICATION A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT A (+) D. OUTPUT A (RTN) E. OUTPUT B (+) * F. OUTPUT B (RTN)
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT LEVEL DETECTOR SERIES S204
PART NO. TRIP POINT PART NO. TRIP POINT S204-100..................... 100mA S204-1.2 .................................1.2A S204-150..................... 150mA S204-2 ..................................... 2A S204-350..................... 350mA S204-3 .................................... 3A S204-550..................... 550mA S204-5 .................................... 5.75A S204-1......................... 1A INPUT RANGE ............................................................................. 0 to 10Amps D.C. TRIP POINT...................................................................... See Table OUTPUT RELAY CONTACT (SPST) .............................................. Energized at & above set point CONTACT RATING ......................................................... 1 Amp @ 28V and 5V RMS TRIP POINT ACCURACY ................................................ ±4% set point TRIP POINT REPEATABILITY ........................................ ± 2% of set point RESET .............................................................................. Automatic when current falls 15% below trip point RESPONSE TIME ............................................................ 3 m-sec max. ISOLATION....................................................................... 350V RMS @ sea level POWER SUPPLY SUPPLY VOLTAGE ......................................................... 22.8 to 30.4Vdc CURRENT DRAIN............................................................ 70mA max. REVERSE POLARITY PROTECTION ............................ 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -20°C to +70°C STORAGE TEMPERATURE RANGE ............................. -55°C to +85°C DIELECTRIC STRENGTH ............................................... 350V RMS MIL-STD-202 Method 301 INSULATION RESISTANCE............................................ 200 M-Ohms min. MIL-STD-202 Method 302 Test Condition A ALTITUDE......................................................................... Operating sea level to 100,000 ft., MIL-STD-202, Method 105, Condition A VIBRATION....................................................................... Operating 0.06 inch D.A., 10Hz to 55Hz MIL-STD-202, Method 201 SHOCK ............................................................................. Operating 50g 11m-sec MIL-STD-202, Method 213, Condition A MOISTURE RESISTANCE .............................................. MIL-STD-202, Method 106 OPERATING HUMIDITY.................................................. 0 to 95% RH ATTITUDE ........................................................................ Meets specification for any mounting position WEIGHT ........................................................................... 12 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S204-800 G AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
DC CURRENT LEVEL DETECTOR
SERIES S58-800 CURRENT ACTUATION LEVELS ZERO CURRENT INPUT.........................................CONDITION A 200mA to 10A Max. ..................................................CONDITION B OUTPUT CONDITION A (ZERO CURRENT) .........................1K-Ohm max. between terminal 1 & 2 CONDITION B (ABOVE 200mA)..............................40K-Ohm min. between terminal 1 & 2 EXCITATION VOLTAGE VOLTAGE..................................................................28Vdc Nominal 22.8 to 30.4 Vdc min. to max. voltage. RESPONSE..............................................................1 m-sec. max. ADJUSTMENTS .......................................................None RESET FROM COND. B TO COND. A ...................Automatic when current levels falls within 0 to 200 mA. ENVIRONMENTAL TEMPERATURE RANGE ........................................0°C to 70°C
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S58-800 A AAC
TERMINAL IDENTIFICATION 1. +28Vdc EXCITATION VOLTAGE 2. OUTPUT 3. EXCITATION RETURN AND
OUTPUT RETURN (DC COMMON)
BARRIER BLOCK TERMINAL 6-23 TERMINAL SCREWS.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE: 1. MOLDED TERMINAL BLOCK WITH 8-32 TERMINAL SCREWS, 7/16 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 12 AWG. TORQUE 9 IN-LB MAX. 2. RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT LOCKWASHER AND #8 FLAT WASHER. TORQUE MAXIMUM 18 IN-LB.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S754 C AAC
DC CURRENT LEVEL DETECTOR PART NUMBER S754-1
INPUT RANGE .................................................... 0 to +20Adc (Continuous) TRIP POINT SETTING SET POINT............................................... 625mAdc TRIP POINT REPEATABILITY................ 5% TRIP POINT RESPONSE TIME ............ 100 m-sec.
ADJUSTMENT RANGE * ........................ Field Adjustable From 500mAdc to 1Adc RESET POINT SETTING RESET ..................................................... Manual by depressing reset switch (S1) . OUTPUT RELAY (Solid State) RELAY CONTACT (SPST) ...................... Contacts Open at and above trip point CONTACT RESISTANCE........................ On 1.5 Ohms Max, Off 100M Ohms Min. DIELECTRIC STRENGTH ...................... 2.5KV RMS 60Hz CURRENT RATING ................................ 600mAdc max. OPEN CIRCUIT VOLTAGE……………… 55Vdc Max. INDICATOR.............................................. LED on at & above trip point POWER SUPPLY SUPPLY VOLTAGE ................................ +25 to 45Vdc CURRENT DRAIN.................................... 40mA max. TRANSIENT PROTECTION.................... ±60V Peak (30sec.); ±100V Peak (2m sec.) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -40°C to +85°C STORAGE TEMPERATURE ................... -45°C to +85°C OPERATING HUMIDITY ........................ 0 to 95% Relative Humidity INSULATION RESISTANCE .................. 500 M-ohms @ 500Vdc DIELECTRIC STRENGTH ...................... 2.5Kv RMS 60Hz PRIMARY CONDUCTOR VOLTAGE ..... 1000Vdc max. CASE ........................................................ Moulded Plastic (GE Lexan) Meets UL Flammability Rating 94 V-0 WEIGHT .................................................. 12 oz. max. * FACTORY SET AT 750mA
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
D.C. CURRENT LEVEL DETECTOR PART NUMBER S201-800
TRIP POINT (AS CURRENT DECREASES) ........................................ 1Amp DC ±0.15Amp TRIP POINT REPEATABILITY.............................................................. ±0.02 Amps, DC RESET.................................................................................................... Automatic when input current rises approximately 0.15 A above trip point CURRENT RANGE................................................................................ 0 to 100 Amps, DC OUTPUT.................................................................................................SPDT Relay Contacts CONTACT RATING ............................................................................... 1A Resistive @ 28Vdc or 5V 400Hz 200mA Inductive. 100mA Lamp. OUTPUT ISOLATION ............................................................................ 350V RMS at sea level EXCITATION.......................................................................................... 28Vdc, Nominal @ 70mA, max. RESPONSE............................................................................................ 200 m-sec max. TEMPERATURE RANGE ...................................................................... -55°C to +70°C WEIGHT ................................................................................................. 16 oz. max. (unit) 1 oz. max. (mating conn.) MOUNTING............................................................................................ Rigid in any position DO-160 ENV. CAT. ................................................................................ A2D2/A/CJL/EXXXFSX/ABZ/AB/ZA DO-160 ENVIRONMENT CATEGORY TEMPERATURE A2D2 HUMIDITY A VIBRATION CJL EXPLOSION E WATERPROOFNESS X HYDRAULIC FLUID X SAND AND DUST X FUNGUS RESISTANCE F SALT SPRAY S MAGNETIC EFFECT X POWER INPUT (NORMAL OPERATING CONDITIONS ONLY) ABZ VOLTAGE SPIKES AB AUDIO FREQUENCY CONDUCTED SUSCEPTIBILITY Z ELECTROMAGNETIC COMPATIBILITY A
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S201-800 J AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
NOTE: 1. MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE. TORQUE 8 IN-LB MAX. 2. PART TO BE IDENTIFIED WITH ADTRANZ PART NUMBER & REVISION LEVEL IN ACCORDANCE WITH SAE AS478-30, LATEST REVISION. CHARACTER HEIGHT SHALL BE .50 INCH MAX. APPROX. WHERE SHOWN. 3. REFERENCE DOCUMENT NO. E301-005.RFP (XIZ). 4. RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT LOCKWASHER AND #8 FLAT WASHER. TORQUE MAXIMUM 18 IN-LB. 5. YELLOW MARKING PAINTED FOR PROTOTYPE IDENTIFICATION.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S680 D AAC
DC CURRENT LEVEL DETECTOR PART NUMBER S680
INPUT RANGE .................................................... 0 to ± 1000Adc (Continuous) OVERLOAD / TRANSIENT...................... ± 2004A RMS (1 min) ± 1635A RMS (30 min) ± 2960A Peak (5 sec.) TRIP POINT SETTING SET POINT............................................... ±3Adc (±10%) TRIP POINT DELAY (TYPICAL) ............ 350 m-sec. After input (Absolute Value) Exceeds Trip Point ADJUSTMENT RANGE ........................... Field Adjustable ±3 to ±5Adc RESET POINT SETTING RESET POINT……………………………. One Amp (Absolute Value) Below Trip Point RESET POINT DELAY (TYPICAL)……... 10 Sec. After Input (Absolute Value) Decreases Below Reset Point OUTPUT RELAY (Solid State) RELAY CONTACT (SPST) ...................... Contacts Close at and above trip point CONTACT RESISTANCE........................ On 25 Ohms Max, Off 500M Ohms Min. DIELECTRIC STRENGTH ...................... 3.3KV RMS 60Hz CURRENT LIMIT PROTECTION ............ Automatically Limits Contact Current to 370mA OPEN CIRCUIT VOLTAGE……………… 200Vdc OR Peak Max DUTY CYCLE……………………………… Number Of “Change Of State” Operations Is Unlimited. POWER SUPPLY SUPPLY VOLTAGE ................................ +25 to 45Vdc CURRENT DRAIN.................................... 25mA max. TRANSIENT PROTECTION.................... ±60V Peak (30sec.); ±100V Peak (2m sec.) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -25°C to +75°C STORAGE TEMPERATURE ................... -40°C to +85°C SHOCK & VIBRATION ............................ IAW ADTRANZ Doc. ABB-ES-091291-1 OPERATING HUMIDITY ........................ 0 to 95% Relative Humidity INSULATION RESISTANCE .................. 500 M-ohms @ 500Vdc DIELECTRIC STRENGTH ...................... 3.3Kv RMS 60Hz PRIMARY BAR VOLTAGE ...................... 2Kv RMS max. CASE ........................................................ Moulded Plastic (GE Lexan) Meets UL Flammability Rating 94 V-0 WEIGHT .................................................. 6.5 lbs. max.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE: 1. MOULDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE. TORQUE 8 IN-LB MAX. 2. PART TO BE IDENTIFIED WITH ADTRANZ PART NUMBER & REVISION LEVEL IN ACCORDANCE WITH SAE AS478-30, LATEST REVISION. CHARACTER HEIGHT SHALL BE .50 INCH MAX. APPROX. WHERE SHOWN. 3. REFERENCE DOCUMENT NO. E301-005.RFP (XIZ). 4. RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT LOCKWASHER AND #8 FLAT WASHER. TORQUE MAXIMUM 18 IN-LB.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S629 D AACAAC
DC CURRENT LEVEL DETECTOR PART NUMBER S629-50
INPUT RANGE .................................................... 0 to ± 1000Adc OVERLOAD / TRANSIENT ..................... ± 1422A RMS (1 min) ± 1375A RMS (4 min) ± 1161A RMS (30 min) ± 2168A peak (5 sec.) ± 2514A tr (18 M-sec.) TRIP POINT SET POINT .............................................. ±45Adc HYSTERESIS ......................................... Auto reset 5Adc ±5% below trip point REPEATABILITY ..................................... ±0.5 Adc OUTPUT RELAY CONTACT (SPST)...................... Actuated at and above trip point CONTACT RATING................................. 10amp @ 45Vdc RESPONSE ............................................ 50M-sec. MAX. DIELECTRIC STRENGTH ..................... 4000 V RMS coil to contact 1000 V RMS between open contact POWER SUPPLY SUPPLY VOLTAGE ................................ +25 to 45Vdc CURRENT DRAIN ................................... 75mA max. PROTECTION ......................................... Reverse polarity protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -25°C to +75°C STORAGE TEMPERATURE................... -40°C to +85°C SHOCK & VIBRATION ........................... IAW ADTRANZ Doc. ABB-ES-091291-1 OPERATING HUMIDITY ....................... 0 to 95% Relative Humidity INSULATION RESISTANCE .................. 500 M-ohms @ 500Vdc DIELECTRIC STRENGTH ..................... 3.3Kv RMS 60Hz PRIMARY BAR VOLTAGE ..................... 2Kv RMS max. CASE........................................................ Moulded Plastic (GE Lexan) Meets UL Flammability Rating 94 V-0 WEIGHT .................................................. 6.5 lbs. max.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE: 1. MOULDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE. TORQUE 8 IN-LB MAX. 2. PART TO BE IDENTIFIED WITH ADTRANZ PART NUMBER & REVISION LEVEL IN ACCORDANCE WITH SAE AS478-30, LATEST REVISION. CHARACTER HEIGHT SHALL BE .50 INCH MAX. APPROX. WHERE SHOWN. 3. REFERENCE DOCUMENT NO. E301-006.RFP (XID). 4. RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT LOCKWASHER AND #8 FLATWASHER. TORQUE MAXIMUM 18 IN-LB.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S623 K AACAAC
DC CURRENT LEVEL DETECTOR PART NUMBER S623-50
INPUT INPUT CURRENT.................................... 0 to ± 1009Adc continuous OVERLOAD ............................................. ± 2360A Transient (18 m-sec) ± 2014A Peak (5 sec) ± 1268A RMS (1 min) ± 1221A RMS (4 min) ± 1009A RMS (30 min) TRIP POINT ADJUSTABLE.......................................... ± 10 to ± 50Adc HYSTERESIS........................................... Auto reset 5 Adc ±5% below trip point OUTPUT RELAY CONTACT (SPST)...................... Actuated at above trip point CONTACT RATING................................. 10amp @ 125Vdc RESPONSE ............................................ 50M-sec. MAX. DIELECTRIC STRENGTH ..................... 4000 V RMS coil to contact 1000 V RMS between open contact POWER SUPPLY SUPPLY VOLTAGE ................................ +25 to 45Vdc CURRENT DRAIN ................................... 125mA max. REVERSE POLARITY PROTECTION.... 10uA current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -25°C to +70°C STORAGE TEMPERATURE................... -45°C to +85°C SHOCK & VIBRATION ........................... IAW ADTRANZ Doc. ABB-ES-091291-1 OPERATING HUMIDITY ....................... 0 to 95% Relative Humidity INSULATION RESISTANCE .................. 500 M-ohms @ 500Vdc PRIMARY BAR VOLTAGE ..................... 2Kv RMS max. DIELECTRIC STRENGTH ..................... 3.3kV RMS 60Hz ISOLATION .............................................. Input/Output/Supply and Case 200 Meg-Ω @ 500Vdc CASE........................................................ Moulded Plastic (GE Lexan) Meets UL Flammability Rating 94 V-0 WEIGHT .................................................. 8 lbs. max.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE: MINIMUM DC SUPPLY VOLTAGE = 7V + .02 (RL) RL = ANY VALUE BETWEEN 0 AND 1400 OHMS. .
AC CURRENT TRANSDUCER MODEL 1055L
4 TO 20mA 2 WIRE LOOP OPERATION PART NO. INPUT RANGE PART NO. INPUT RANGE 1055L-50............... 0 to 50mA 1055L-250 ............................... 0 to 250mA 1055L-100............. 0 to 100mA 1055L-500 ............................... 0 to 500mA 1055L-200............. 0 to 200mA 1055L-1A................................. 0 to 1A INPUT RANGE..................................................... Aac See Table FREQUENCY........................................... 50 to 60 Hz OVERLOAD CONTINUOUS ................... 250Aac OVERLOAD TRANSIENT ....................... 100 Times Range For 250m-sec. OUTPUT CURRENT SIGNAL ................................. 4 to 20mAdc FS (Full Scale) ACCURACY ............................................. ±0.5% FS or ±0.1mA max. (Over Temperature Range) RIPPLE..................................................... ±0.25% FS (±0.05 mA RMS) RESPONSE (10 to 90%).......................... 100mS max. LOAD RESISTANCE (RL) ....................... 250 Ohms Nominal LOAD RESISTANCE RANGE ................. 0 to 1400 Ohms (See Note) CURRENT SIGNAL @ OVERLOAD....... 30mA TYP. PROTECTION ......................................... Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE ................................ 15Vdc Nominal CURRENT DRAIN ................................... 20mA SUPPLY VOLTAGE RANGE................... 7 to 35Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -20° to +85°C STORAGE TEMPERATURE RANGE..... -40° to +85°C ISOLATION .............................................. Input/Output/Case INSULATION RESISTANCE ................... 200 M-Ohms @ 500Vdc INPUT CONDUCTOR VOLTAGE ........... 1.5KV max. (5KV max. with insulated cable) WEIGHT .................................................. 10 oz. Max.
TERMINAL IDENTIFICATION 1. OUTPUT (+) 2. OUTPUT (RTN)
TERMINAL SCREWS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32 WIDE.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1055L C AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE: MINIMUM DC SUPPLY VOLTAGE = 7V + .02 (RL) RL = ANY VALUE BETWEEN 0 AND 1400 OHMS. .
TERMINAL SCREWS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32 WIDE.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S383L-1003AM2 B AACAAC
AC CURRENT TRANSDUCER SERIES S383L
4 TO 20mA 2 WIRE LOOP OPERATION PART NO. INPUT RANGE PART NO. INPUT RANGE S383L-50 .............. 0 to 50mA S383L-250............................... 0 to 250mA S383L-100 ............ 0 to 100mA S383L-500............................... 0 to 500mA S383L-200 ............ 0 to 200mA S383L-1A ................................ 0 to 1A INPUT RANGE..................................................... Aac See Table FREQUENCY........................................... 50 to 60 Hz OVERLOAD CONTINUOUS ................... 250Aac OVERLOAD TRANSIENT ....................... 100 Times Range For 250m-sec. OUTPUT CURRENT SIGNAL ................................. 4 to 20mAdc FS (Full Scale) ACCURACY ............................................. ±0.5% FS or ±0.1mA max. (Over Temperature Range) RIPPLE..................................................... ±0.25% FS (±0.05 mA RMS) RESPONSE (10 to 90%).......................... 100mS max. LOAD RESISTANCE (RL) ....................... 250 Ohms Nominal LOAD RESISTANCE RANGE ................. 0 to 1400 Ohms (See Note) CURRENT SIGNAL @ OVERLOAD....... 30mA TYP. PROTECTION ......................................... Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE ................................ 15Vdc Nominal CURRENT DRAIN ................................... 20mA SUPPLY VOLTAGE RANGE................... 7 to 35Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -40° to +85°C STORAGE TEMPERATURE RANGE..... -40° to +85°C ISOLATION .............................................. Input/Output/Case INSULATION RESISTANCE ................... 200 M-Ohms @ 500Vdc INPUT CONDUCTOR VOLTAGE ........... 1.5KV max. (5KV max. with insulated cable) CASE **.................................................... Aluminum type 1100-0 (finish black semi-gloss enamel) WEIGHT .................................................. 10 oz. Max.
TERMINAL IDENTIFICATION 1. OUTPUT (+) 2. OUTPUT (RTN)
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
AC CURRENT TRANSDUCER SERIES 1002M1
MODEL NO. INPUT CURRENT MODEL NO. INPUT CURRENT 1002M1-250mA .... 0 to 0.25 1002M1-25 .............................. 0 to 25 1002M1-500mA .... 0 to 0.50 1002M1-50 .............................. 0 to 50 1002M1-1.............. 0 to 1 1002M1-65 .............................. 0 to 65 1002M1-5.............. 0 to 5 1002M1-100 ............................ 0 to 100 1002M1-10............ 0 to 10 1002M1-150 ............................ 0 to 150 1002M1-20............0 to 20 1002M1-200 ............................ 0 to 200 1002M1-250 ............................0 to 250 INPUT CURRENT RANGE..................................................... Aac See Table (ADDITIONAL RANGES AVALIABLE) FREQUENCY........................................... 400 Hz (50 & 60 Hz models available) FREQUENCY RANGE............................. 375 TO 475 Hz OVERLOAD ............................................. 500Aac Continuously OUTPUT VOLTAGE SIGNAL.................................. 0 to +5Vdc FS (Full Scale) ACCURACY ............................................. ±0.5% FS (±25mA) RESPONSE (10 to 90%).......................... 10 m-sec max. RIPPLE..................................................... 10mV RMS max. TEMPERATURE COEFFICIENT ............ ±0.005% FS /°C max. OUTPUT IMPEDANCE............................ 1000Ohms ±5% OUTPUT PROTECTION ......................... Output terminals E & C will withstand ±32Vdc or short circuit continuously POWER SUPPLY SUPPLY VOLTAGE ................................ 28Vdc ±4Vdc CURRENT DRAIN ................................... 100mA max. OVER VOLTAGE PROTECTION............ Terminals A & B withstand ±35Vdc without damage REVERSE POLARITY PROTECTION.... 10uA max. current drain without damage. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -55° to +85°C STORAGE TEMPERATURE RANGE..... -55° to +125°C DIELECTRIC STRENGTH ...................... 350V RMS (all terminals to case) INSULATION RESISTANCE ................... 100 M-Ohms (all terminals to case) ALTITUDE................................................ Operating sea level to 60,000 ft. VIBRATION.............................................. Operating- 0.06 in. D.A., 10 to 55Hz (method 201 of MIL-STD-202) SHOCK..................................................... Operating 50G, 11 m-sec half sine pulse method 213, Condition A of MIL-STD-202 MOISTURE RESISTANCE ..................... Will meet method 106 of MIL-STD-202 and method 507.1 Proc. 1 of MIL-STD-810 OPERATING HUMIDITY ......................... 0% to 95% RH ATTITUDE................................................ Unit will perform as specified when mounted in any position WEIGHT .................................................. 1.25 lbs. Max. TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT SIGNAL (RTN) D. SPARE E. OUTPUT SIGNAL (+) F. SPARE
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1002M1 N AAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC RMS CURRENT SENSOR SERIES S402
INPUT CURRENT INPUT CURRENT PART NO. RANGE A RMS PART NO. RANGE A RMS S402-250mA ............... 0 TO 250mA S402-20 ...................................0 TO 20A S402-500mA ............... 0 TO 500mA S402-50 .................................. 0 TO 50A S402-1......................... 0 TO 1A S402-100 ................................ 0 TO 100A S402-2......................... 0 TO 2A S402-150 ................................ 0 TO 150A S402-5......................... 0 TO 5A S402-200 .................................0 TO 200A S402-10....................... 0 TO 10A S402-250 .................................0 TO 250A INPUT RANGE ..................................................................... See Table FREQUENCY RANGE ............................................. 57 to 63Hz (50 & 400Hz model available) OVERLOAD.............................................................. 200A continuously OUTPUT VOLTAGE SIGNAL................................................... 0 to 5Vdc FS (Full Scale) ACCURACY.............................................................. ±.5% FS (±25mV) RESPONSE (0 to 90%) ............................................ 100 m-sec RIPPLE ..................................................................... 10mV RMS max. TEMPERATURE COEFFICIENT............................. ± .02% FS/°C max. OUTPUT IMPEDANCE ............................................ 1000 Ohms ±5% OUTPUT PROTECTION.......................................... Output terminals E & C will withstand 32Vdc or short circuit continuously POWER SUPPLY SUPPLY VOLTAGE ................................................. 28Vdc ±4Vdc CURRENT DRAIN.................................................... 100mA max. OVER VOLTAGE PROTECTION ............................ Terminals A & B withstand ±35Vdc without damage REVERSE POLARITY PROTECTION .................... 10µA max current drain without damage. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.................. -0°C to +70°C STORAGE TEMPERATURE RANGE ..................... -25°C to +85°C DIELECTRIC STRENGTH ....................................... 350V RMS (all terminals to case) INSULATION RESISTANCE.................................... 100M-Ohms (all terminals to case) ALTITUDE................................................................. Operating: sea level to 60,000 ft. VIBRATION............................................................... Operating: 0.06 in. D.A., 10 to 55 Hz (Method 201 of MIL-STD-202) SHOCK ..................................................................... Operating: 50g, 11 m-sec half sine pulse Method 213, Condition A of MIL-STD-202. MOISTURE RESISTANCE ...................................... Will meet Method 106 of MIL-STD-202 and Method 507.1 Proc. 1 of MIL-STD-810. OPERATING HUMIDITY.......................................... 0% to 95% RH ATTITUDE ................................................................ Unit will perform as specified when mounted in any position. WEIGHT ................................................................... 1.25 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S402-1004 B AACAAC
TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY VOLTAGE (RTN) C. OUTPUT (RTN) D. SPARE E. OUTPUT (+) F. SPARE
ADD “-P” TO MODEL NUMBER FOR SPECIAL POTTING. SENSOR IS CAPABLE OF OPERATING WHILE SUBMERGED IN TRANSFORMER OIL.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT TRANSDUCER
SERIES C
SELF - POWERED
PART INPUT OVERLOAD CAPABILITY AMPS AC
NUMBER CURRENT CONTINUOUS TRANSIENT SEC/HR
C-1........................................0 to 1A ............................... 10A ...................................... 50A
C-2........................................0 to 2A ............................... 15A ...................................... 100A
C-5........................................0 to 5A ............................... 15A ...................................... 250A
C-10......................................0 to 10A ............................. 20A ...................................... 500A
C-20......................................0 to 20A ............................. 30A ...................................... 500A INPUT RANGE ...................................................................................... Aac See Table FREQUENCY ............................................................................ 47 to 1000Hz LINEAR OVER RANGE............................................................. 20% of Range OVER LOAD CAPABILITY........................................................ Aac See Table DIELECTRIC.............................................................................. 2KV RMS, 60Hz, 1 min. BURDEN.................................................................................... 0.5VA max. OUTPUT CURRENT SIGNAL................................................................... 0 to 1mA FS (Full Scale) ACCURACY * (60Hz)................................................................. ±0.25% FS (47 to 1000Hz).................................................... ±0.5% FS. RIPPLE ...................................................................................... 0.5% FS peak max. RESPONSE (0 to 99%) ............................................................. 400m-sec. max. LOAD RESISTANCE RANGE................................................... 0 to 11K-Ohms CALIBRATION ADJUSTMENT................................................. ±10% FS STABILITY PER YEAR.............................................................. ±0.1% FS max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE................................................. -20° to +70°C STORAGE TEMPERATURE .................................................... -55° to +85°C ISOLATION................................................................................ Input/Output/Case INSULATION RESISTANCE..................................................... 100m-Ohms min. @ 500Vdc SURGE CAPABILITY ................................................................ IEEE SWC transient test WEIGHT ................................................................................... 16 oz. Typ.
* INCLUDES COMBINED WORSE CASE EFFECTS OF TEMPERATURE AND LOAD CHANGES. TERMINAL IDENTIFICATION
1. OUTPUT SIGNAL (+) 2. OUTPUT (RTN) 3. AC INPUT 4. AC INPUT
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-C C AACAAC NOTE: MOLDED TERMINAL BLOCK WITH 8-32 SCREWS 7/16 IN. CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 12 AWG AND LUGS UP TO 3/8 IN. WIDE.
ADD “-E” AND OR “-F” TO PART NUMBER FOR SPECIAL OPTIONS
“-E” OUTPUT VOLTAGE OPTION ADD -E PLUS DESIRED OUTPUT VOLTAGE FROM 0 TO A MAX OF 10
“-F” CALIBRATION FREQ. OPTION ADD -F PLUS DESIRED CALIBRATION FREQ. FROM 47 TO 1000
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC VOLTAGE TRANSDUCER
SERIES CX
4 TO 20mA LOOP - POWERED
PART INPUT OVERLOAD CAPABILITY AMPS AC
NUMBER CURRENT CONTINUOUS TRANSIENT SEC/HR
CX-1....................................... 0 to 1A.................................. 10A............................................... 50A
CX-2....................................... 0 to 2A.................................. 15A............................................... 100A
CX-5....................................... 0 to 5A.................................. 15A............................................... 250A
CX-10..................................... 0 to 10A................................ 20A............................................... 500A
CX-20..................................... 0 to 20A................................ 30A............................................... 500A INPUT RANGE...................................................................................... Aac See Table FREQUENCY............................................................................ 47 to 1000Hz LINEAR OVER RANGE............................................................ 20% of Range OVER LOAD CAPABILITY ....................................................... Aac See Table DIELECTRIC............................................................................. 2KV RMS, 60Hz, 1 min. BURDEN ................................................................................... 0.5VA max. OUTPUT CURRENT SIGNAL .................................................................. 4 to 20mA FS (Full Scale) ACCURACY * (60Hz)................................................................ ±0.25% FS (47 to 1000Hz .................................................... ±0.5% FS. RIPPLE...................................................................................... 0.5% FS peak max. RESPONSE (0 to 99%)............................................................. 400m-sec. max. LOAD RESISTANCE ................................................................ 250 Ohms Nominal LOAD RESISTANCE RANGE .................................................. 0 to 250 Ohms @ 15Vdc 0 to 1100 Ohms @ 32Vdc PROTECTION .......................................................................... Reverse Polarity Protected CALIBRATION ADJUSTMENT ................................................ ±10% of FS STABILITY PER YEAR............................................................. ±0.1% FS max. POWER SUPPLY SUPPLY VOLTAGE.................................................................. +15Vdc Nominal CURRENT DRAIN .................................................................... 20mA SUPPLY VOLTAGE RANGE.................................................... 10 to 35Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ................................................ -20° to +70°C STORAGE TEMPERATURE.................................................... -55° to +85°C ISOLATION ............................................................................... Input/Output/Case INSULATION RESISTANCE .................................................... 100m-Ohms min. @ 500Vdc SURGE CAPABILITY................................................................ IEEE SWC transient test WEIGHT ................................................................................... 16 oz. Typ. * INCLUDES COMBINED WORSE CASE EFFECTS OF TEMPERATURE, SUPPLY VOLTAGE AND LOAD CHANGES.
TERMINAL IDENTIFICATION 1. OUTPUT SIGNAL (+) 2. OUTPUT (RTN) 3. AC INPUT 4. AC INPUT
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-CX D AACAAC NOTE: MOLDED TERMINAL BLOCK WITH 8-32 SCREWS 7/16 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 12 AWG AND LUGS UP TO 3/8 IN. WIDE.
ADD “-F” TO PART NUMBER PLUS DESIRED CALIBRATION FREQ. FROM 47 TO 1000Hz FOR CALIBRATION FREQ. OPTION.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
A.C.CURRENT SENSOR SERIES 1003AM1
OUTPUT
MODEL NO. INPUT CURRENT IMPEDANCE 1003AM1-2...............................0 to 2Aac ...........................................................25 1003AM1-5...............................0 to 5Aac ...........................................................10 1003AM1-10.............................0 to 10Aac ........................................................5.0 1003AM1-15.............................0 to 15Aac ........................................................4.0 1003AM1-20.............................0 to 20Aac ........................................................2.5 1003AM1-25.............................0 to 25Aac ........................................................2.2 1003AM1-30.............................0 to 30Aac ........................................................2.0 1003AM1-50.............................0 to 50Aac ........................................................1.0 1003AM1-60.............................0 to 60Aac ........................................................0.8 1003AM1-75.............................0 to 75Aac ......................................................0.75 1003AM1-100...........................0 to 100Aac ......................................................0.5 INPUT CURRENT RANGE................................................................................ See Table FREQUENCY ......................................................................................... 60Hz FREQUENCY RANGE........................................................................... 57 to 63Hz OVERLOAD............................................................................................ 250Aac Continuous OUTPUT VOLTAGE SIGNAL ................................................................................ 0 to 5Vdc FS (Full Scale) ACCURACY............................................................................................ ± 1% FS for 10A range and above ±2% FS for 2A & 5A ranges RIPPLE ................................................................................................... 3% FS RMS max. RESPONSE............................................................................................ 150 m-sec max. REPEATABILITY.................................................................................... ± 0.5% FS TEMPERATURE COEFFICIENT........................................................... ± 0.04% FS/ °C max. for 10A ranges & above ±0.08% FS/°C for 2A & 5A ranges OUTPUT IMPEDANCE.......................................................................... K-Ohms See Table OUTPUT SIGNAL @ OVERLOAD ....................................................... 11Vdc max. POWER SUPPLY SUPPLY VOLTAGE ............................................................................... None, self excited ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE ............................................... - 20° C to 70°C STORAGE TEMPERATURE RANGE................................................... - 55°C to 85°C ISOLATION ............................................................................................ Input/Output/Case INSULATION RESISTANCE ................................................................. 100 M-Ohms output to case WEIGHT ................................................................................................. 5 oz. max.
TERMINAL IDENTIFICATION
RED LEAD: OUTPUT (+) BLACK LEAD: OUTPUT (RTN)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1003AM1 K AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
A.C. CURRENT SENSOR
SERIES 1004
INPUT OUTPUT INPUT OUTPUT
PART NO. CURRENT IMPEDANCE PART NO. CURRENT IMPEDANCE
1004-2.......................0 TO 2 ................ 25 1004-150............ 0 TO 150 .................... 0.9
1004-5...................... 0 TO 5 ................ 10 1004-200............ 0 TO 200 ................... . 0.6
1004-10.................. 0 TO 10 ................ 5.0 1004-250............ 0 TO 250 .................... 0.5
1004-20...................0 TO 20 ................ 2.5 1004-300............ 0 TO 300 .................... 0.5
1004-50...................0 TO 50 ................ 1.0 1004-350............ 0 TO 350 .................... 0.4
1004-100...............0 TO 100 ................ 0.5 1004-400............ 0 TO 400 .................... 0.3
INPUT CURRENT RANGE...................................................................................... Aac See Table FREQUENCY ............................................................................ 400Hz FREQUENCY RANGE.............................................................. 375 to 475Hz OVERLOAD............................................................................... 500Aac continuously OUTPUT VOLTAGE SIGNAL ................................................................... 0 to +5Vdc FS (Full Scale) ACCURACY............................................................................... ± 0.5% FS (±25mV) RESPONSE............................................................................... 150 m-sec max. RIPPLE ...................................................................................... 0.4% FS RMS TEMPERATURE COEFFICIENT.............................................. ±0.04% FS/°C max. OUTPUT IMPEDANCE............................................................. K-Ohms max. See Table REPEATABILITY....................................................................... ±0.1% FS OUTPUT SIGNAL @ OVERLOAD ........................................... 11Vdc typical POWER SUPPLY (PS) SUPPLY VOLTAGE ................................................................. Non, Self Excited ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .................................. -55° to +85°C STORAGE TEMPERATURE RANGE...................................... -60° to +100°C INSULATION RESISTANCE .................................................... 100M-Ohms (Terminals A thru E to case & terminal F) DIELECTRIC STRENGTH........................................................ 350V RMS (Terminals A thru E to case & terminal F) ALTITUDE ................................................................................. Operating sea level to 60,000 ft. VIBRATION ............................................................................... Operating - 0.06 in D.A., 10 to 55Hz method 201 of MIL-STD-202 SHOCK...................................................................................... Operating 50g, 11m-sec half sine pulse method 213 Condition A of MIL-STD-202 MOISTURE RESISTANCE ....................................................... Will meet method 106 of MIL-STD-202 and method 507.1 proc. 1 of MIL-STD-810 OPERATING HUMIDITY........................................................... 0% to 95% RH ATTITUDE................................................................................. Unit will perform as specified when mounted in any position WEIGHT .................................................................................... 1.25 lbs. Max.
TERMINAL IDENTIFICATION
A. SPARE B. SPARE C. OUTPUT (RTN) D. SPARE E. OUTPUT (+) F. CASE GROUND
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1004 G AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
°
A.C. CURRENT SENSOR
SERIES 1005
CURRENT OUTPUT CURRENT OUTPUT
RANGE IMPEDANCE RANGE IMPEDANCE
PART NO. AMPS AC K OHMS PART NO. AMPS AC K OHMS
1005-2................................2 ................ 25 1005-50..........................50 .................... 1.5
1005-5................................5 ................ 10 1005-75..........................75 ................... . 1.0
1005-10............................10 ................ 7.0 1005-100......................100 .................... 0.7
1005-15............................15 ................ 5.0 1005-150......................150 .................... 0.5
1005-20............................20 ................ 3.5 1005-200......................200 .................... 0.4
1005-25............................25 ................ 3.0 1005-250......................250 .................... 0.3
1005-30............................30 ................ 2.5 1005-300......................300 .................... 0.25
1005-40............................40 ................ 1.75
INPUT CURRENT RANGE...................................................................................... See Table OPERATING FREQUENCY ..................................................... 50 to 60Hz OVERLOAD CONTINUOUS..................................................... 200A (2 to 100A ranges) 400A (150 to 300A ranges) OUTPUT VOLTAGE SIGNAL ................................................................... 0 to 5Vdc FS (Full Scale) ACCURACY............................................................................... ± 1% FS for 10A range and above ±2% FS for 2A and 5A ranges RIPPLE ...................................................................................... 100mV RMS typical RESPONSE (10 to 90%) ........................................................... 80m-sec typical IMPEDANCE ............................................................................. See Table TEMPERATURE COEFFICIENT.............................................. ±0.04% FS/°C max. ±0.08% FS/°C max. (2 & 5A units) REPEATABILITY....................................................................... ±0.1% FS VOLTAGE SIGNAL @ OVERLOAD......................................... 11Vdc max. VOLTAGE SIGNAL LINEAR TO............................................... 6Vdc (120% FS) POWER SUPPLY (PS) SUPPLY VOLTAGE ................................................................. Non, Self Excited ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .................................. -20° to +70°C STORAGE TEMPERATURE RANGE...................................... -55° to +85°C ISOLATION ............................................................................... Input/Output/Case CONDUCTOR CABLE VOLTAGE............................................ 1.5KV max. (5KV with Insul. Cable) CASE ........................................................................................ Molded Plastic Meets UL Flammability Rating 94V- 0 WEIGHT ................................................................................... 5 oz. max.
TERMINALS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING, ACCEPTS WIRE SIZES UP TO 14 AWG AND WIRE LUGS UP TO 9/32” WIDE.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1005 J AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT TRANSDUCER MODEL 1055
4 TO 20mA 2 WIRE LOOP OPERATION PART NO. INPUT RANGE PART NO. INPUT RANGE 1055-2 .................. 0 to 2Aac 1055-40 .................................. 0 to 40Aac 1055-5 .................. 0 to 5Aac 1055-50 .................................. 0 to 50Aac 1055-10 ................ 0 to 10Aac 1055-75 .................................. 0 to 75Aac 1055-15 ................ 0 to 15Aac 1055-100 ................................ 0 to 100Aac 1055-20 ................ 0 to 20Aac 1055-150 ................................ 0 to 150Aac 1055-25 ................ 0 to 25Aac 1055-200 ................................ 0 to 200Aac 1055-30 ................ 0 to 30Aac 1055-250 ................................0 to 250Aac INPUT RANGE..................................................... Aac See Table FREQUENCY........................................... 50 to 60 Hz OVERLOAD CONTINUOUS ................... 500Aac OVERLOAD TRANSIENT ....................... 10 Times Range For 250m-sec. OUTPUT CURRENT SIGNAL ................................. 4 to 20mAdc FS (Full Scale) ACCURACY ............................................. ±0.5% FS or ±0.1mA max. (Over Temperature Range) RIPPLE..................................................... 10mV RMS max. RESPONSE (10 to 90%).......................... 100mS max. LOAD RESISTANCE (RL) ....................... 250 Ohms Nominal LOAD RESISTANCE RANGE ................. 0 to 1400 Ohms (See Note) CURRENT SIGNAL @ OVERLOAD....... 30mA TYP. PROTECTION ......................................... Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE ................................ 15Vdc Nominal CURRENT DRAIN ................................... 20mA SUPPLY VOLTAGE RANGE................... 5 to 35Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -20° to +85°C STORAGE TEMPERATURE RANGE..... -40° to +85°C ISOLATION .............................................. Input/Output/Case INSULATION RESISTANCE ................... 200 M-Ohms @ 500Vdc INPUT CONDUCTOR VOLTAGE ........... 1.5KV max. (5KV max. with insulated cable) WEIGHT .................................................. 10 oz. Max.
NOTE: MINIMUM DC SUPPLY VOLTAGE = VX + .02 (RL) RL = ANY VALUE BETWEEN 0 AND 1400 OHMS. Vx = 7V FOR P/N S383-2 AND S383-5 VX = 5V FOR P/N S383-10 THRU S383-250
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1055 F AACAAC
TERMINAL IDENTIFICATION 1. OUTPUT (+) 2. OUTPUT (RTN)
TERMINAL SCREWS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32 WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S383-1003AM2 K AACAAC
NOTE: MINIMUM DC SUPPLY VOLTAGE = VX + .02 (RL) RL = ANY VALUE BETWEEN 0 AND 1400 OHMS. Vx = 7V FOR P/N S383-2 AND S383-5 VX = 5V FOR P/N S383-10 THRU S383-250
TERMINAL IDENTIFICATION 1. OUTPUT (+) 2. OUTPUT (RTN)
TERMINAL SCREWS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32 WIDE.
AC CURRENT TRANSDUCER SERIES S383
4 TO 20mA 2 WIRE LOOP OPERATION PART NO. INPUT RANGE PART NO. INPUT RANGE S383-2A................ 0 to 2Aac S383-40A ................................ 0 to 40Aac S383-3A................ 0 to 3Aac S383-50A ................................ 0 to 50Aac S383-5A................ 0 to 5Aac S383-75A ................................ 0 to 75Aac S383-10A.............. 0 to 10Aac S383-100A .............................. 0 to 100Aac S383-15A.............. 0 to 15Aac S383-150A .............................. 0 to 150Aac S383-20A.............. 0 to 20Aac S383-200A .............................. 0 to 200Aac S383-25A.............. 0 to 25Aac S383-250A .............................. 0 to 250Aac S383-30A.............. 0 to 30Aac INPUT RANGE..................................................... Aac See Table FREQUENCY........................................... 50 to 60 Hz OVERLOAD CONTINUOUS ................... 500Aac OVERLOAD TRANSIENT ....................... 10 Times Range For 250m-sec. OUTPUT CURRENT SIGNAL ................................. 4 to 20mAdc FS (Full Scale) ACCURACY ............................................. ±0.5% FS or ±0.1mA max. (Over Temperature Range) RIPPLE..................................................... 10mV RMS max. RESPONSE (10 to 90%).......................... 100mS max. LOAD RESISTANCE (RL) ....................... 250 Ohms Nominal LOAD RESISTANCE RANGE ................. 0 to 1400 Ohms (See Note) CURRENT SIGNAL @ OVERLOAD....... 30mA TYP. PROTECTION ......................................... Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE ................................ 15Vdc Nominal CURRENT DRAIN ................................... 20mA SUPPLY VOLTAGE RANGE................... 5 to 35Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -40° to +85°C STORAGE TEMPERATURE RANGE..... -40° to +85°C ISOLATION .............................................. Input/Output/Case INSULATION RESISTANCE ................... 200 M-Ohms @ 500Vdc INPUT CONDUCTOR VOLTAGE ........... 1.5KV max. (5KV max. with insulated cable) CASE **.................................................... Aluminum type 1100-0 (finish black semi-gloss enamel) WEIGHT .................................................. 10 oz. Max.
AC RMS CURRENT TRANSDUCER SERIES 1070 4 to 20mA 2 WIRE LOOP POWER PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE 1070-2.......................... 0 to 2 1070-40………………… 0 to 40 1070-5 .......................... 0 to 5 1070-50………………… 0 to 50 1070-10........................ 0 to 10 1070-75………………… 0 to 75 1070-15………………. 0 to 15 1070-100……………….. 0 to 100 1070-20 ........................ 0 to 20 1070-150 ………………. 0 to 150 1070-25 ........................ 0 to 25 1070-200……………….. 0 to 200 1070-30 ........................ 0 to 30 1070-250………………. 0 to 250 INPUT
RANGE ........................................................................... Aac rms (see table) OVERLOAD ................................................................... 500Aac FREQUENCY RANGE.................................................... 20 to 2KHz OUTPUT CURRENT SIGNAL ........................................................ 4 to 20mAdc FS ACCURACY (Over the Temperature Range).................. ±0.25% FS max. (± 50uA) note 1 RIPPLE ........................................................................... .2% max. (40uAac) RESPONSE (10 to 90%)................................................. 300m-sec. LOAD RESISTANCE (RL) .............................................. 250 Ohms Nominal LOAD RESISTANCE RANGE ........................................ 0 to 300 Ohms CURRENT SIGNAL @ OVERLOAD............................... 23mAdc typ. OUTPUT PROTECTION................................................. Reverse Polarity Protection POWER SUPPLY SUPPLY VOLTAGE ....................................................... +15Vdc CURRENT DRAIN .......................................................... 4 to 23mAdc SUPPLY VOLTAGE RANGE .......................................... +12 TO 32Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE ......................... -40° to +85°C STORAGE TEMPERATURE RANGE............................. -55° to +125°C HUMIDITY (Operating).................................................... 0% to 95%RH MOISTURE RESISTANCE ............................................. MIL-STD-202 Method 106 (note 2) RANDOM VIBRATION (Operating)................................. MIL-STD-810F, Proc.1,Cat.12, WO=.095G2/Hz,
Time1 hr, Fig. 514.5C-8 Overall level 12.G- RMS SHOCK ........................................................................... 50g 11m-sec. half sine pulse ISOLATION..................................................................... Input to output 5KV rms 60Hz/1min. INSULATION RESISTANCE........................................... 500 M-Ohms @ 500Vdc CASE MATERIAL ........................................................... Molded Plastic meets UL flammability rating 94V-O (color light gray) WEIGHT ......................................................................... 6 oz. Max. NOTE 1: Specified accuracy includes the combined worst case effects of Zero Offset, Temperature, Hysteresis, Supply Swings and Current Cable Positioning. NOTE 2: Meets Specified Moisture requirements with option C & D only.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1070 C AAC
TERMINAL IDENTIFICATION 1. SUPPLY (+) 2. SUPPLY (RTN) 3-9. SPARE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT TRANSDUCER
SPLIT CORE RMS RESPONDING
MAXIMUM MODEL RANGE CONTINUOUS 6 SEC. 1 SEC. ACTS-20-05 2A 80A 125A 250A 5A 100A 125A 250A ACTS-20-50 10A 80A 125A 250A 20A 110A 150A 300A 50A 175A 215A 400A ACTS-20-200 100A 200A 300A 600A 150A 300A 450A 800A 200A 400A 500A 1000A
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-ACTS B AAC
ACTS-
SPECIFICATIONS Output Signal 4-20mA, Loop-powered._True RMS__________________________ Output Limit 23mA ______________________________________ Accuracy .08% FS________ __________________ Response Time 600mS (to 90% step change) Frequency Range 10-400Hz Power Supply 24VDC Nominal, 40VDC Maximum__________________________ Isolation Voltage UL listed to 1270VAC, tested to 5KV Input Ranges Field selectable ranges from 0-200A. Consult factory for custom ranges.______ __________________ Sensing Aperture 0.85” (21.5mm) sq. Case UL 94V-0 Flammability rated Environmental -4 to 122° F (-20 to 50° C), 0-95% RH, non-condensing Listing UL 508 Industrial Control Equipment (USA & Canada), CE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT TRANSDUCER SPLIT CORE
AVERAGE RESPONDING MAXIMUM TYPE RANGE CONTINUOUS 6 SEC. 1 SEC. -05 (ACT-20 only) 2A 80A 100A 200A 5A 100A 124A 250A -50 10A 80A 125A 250A 20A 110A 150A 300A 50A 175A 215A 400A -200 100A 200A 300A 600A 150A 300A 450A 800A 200A 400A 500A 1000A
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-ACT B AACAAC
MODEL ACT-05-(type) ACT-10-(type) ACT-20-(type) Output Signal 0-5VDC 0-10VDC 4-20mA Output Limit 10VDC 15VDC 40mA Accuracy 1.0% FS 1.0% FS 0.5% FS Response Time 100mS 100mS 300mS Frequency Range 50-60Hz 50-60Hz 20-100Hz Other Frequencies Special calibration available for any frequency from 10-400Hz Power Supply Self-Powered Self-Powered 12-40VDC Loop-powered Loading 1MΩ minimum for rated accuracy 100mΩ add 1.3% error. Isolation Voltage UL listed to 1270VAC, tested to 5KV Input Range Field selectable ranges from 0-200A. Custom ranges available, consult factory. Sensing Aperture 0.85” (21.5mm) sq. Case UL 94V-0 Flammability rated Environmental -4 to 122° F (-20 to 50° C), 0-95% RH non-condensing Listing UL 508 Industrial Control Equipment (USA & Canada), CE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
A.C. CURRENT SENSOR
SERIES 1006
OUTPUT OUTPUT
MODEL NO. INPUT CURRENT IMPEDANCE MODEL NO. INPUT CURRENT IMPEDANCE
1006-5.......................0 TO 5 ................ 9 1006-200............ 0 TO 200 .................... .22
1006-10...................0 TO 10 ................ 4.5 1006-250............ 0 TO 250 ................... . .18
1006-20...................0 TO 20 ................ 2.2 1006-300........... 0 TO 300 .................... .22
1006-25...................0 TO 25 ................ 1.7 1006-350............ 0 TO 350 .................... .2
1006-35...................0 TO 35 ................ 1.4 1006-400............ 0 TO 400 .................... .17
1006-50...................0 TO 50 ................ .88 1006-500............ 0 TO 500 .................... .13
1006-75...................0 TO 75 ................ .61 1006-600............ 0 TO 600 .................... .11
1006-100...............0 TO 100 ................ .45 1006-800............ 0 TO 800 .................... .12
1006-150...............0 TO 150 ................ .30 1006-1000........ 0 TO 1000 .................... .10
INPUT RANGE...................................................................................... Aac See Table FREQUENCY ............................................................................ 50 & 60Hz OVERLOAD CONTINUOUS..................................................... 500Aac or two X FS which ever is greater OUTPUT VOLTAGE SIGNAL ................................................................... 0 to 5Vdc FS (Full Scale) * ACCURACY............................................................................... ± 0.5% FS RIPPLE (RMS)........................................................................... 10mV RMS typical RESPONSE (10 to 90%) ........................................................... 130m-sec typical IMPEDANCE ............................................................................. K Ohms max. See Table TEMPERATURE COEFFICIENT.............................................. ±0.02% FS/°C max. REPEATABILITY....................................................................... ±0.1% FS VOLTAGE SIGNAL @ OVERLOAD......................................... 10Vdc max. VOLTAGE SIGNAL LINEAR TO............................................... 6Vdc (120% FS) POWER SUPPLY (PS) SUPPLY VOLTAGE ................................................................. None, Self Excited ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .................................. -20° to +70°C STORAGE TEMPERATURE RANGE...................................... -55° to +85°C ISOLATION ............................................................................... Input/Output/Case CONDUCTOR CABLE VOLTAGE............................................ 1.5KV max. (5KV with Insul. Cable) CASE ........................................................................................ Molded Plastic Meets UL Flammability Rating 94V- 0 WEIGHT ................................................................................... 1.2 lbs. max. * 4 to 20mA Two Wire Output Option Available
TERMINALS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING, ACCEPTS WIRE SIZES UP TO 14 AWG AND WIRE LUGS UP TO 9/32” WIDE.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1006 H AACAAC
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT TRANSDUCERAC CURRENT TRANSDUCER SERIES 1006XSERIES 1006X
4 TO 20 mA 2 WIRE OPERATION4 TO 20 mA 2 WIRE OPERATION PART NO.PART NO. INPUT CURRENTINPUT CURRENT PART NO.PART NO. INPUT CURRENTINPUT CURRENT 1006X-5 ................ 5 1006X-200 ............................... 200 1006X-10 .............. 10 1006X-250 ............................... 500 1006X-20 .............. 20 1006X-300 ............................... 300 1006X-25 .............. 25 1006X-400 ............................... 400 1006X-50 .............. 50 1006X-500 ............................... 500 1006X-75 .............. 75 1006X-600 ............................... 600 1006X-100 ............100 1006X-800 ............................... 800 1006X-150 ............150 1006X-1000 .............................1000 1006X-1200 .............................1200 INPUT CURRENT INPUT CURRENT RANGE..................................................... See Table FREQUENCY ........................................... 50 & 60 Hz OVERLOAD CONTINUOUS.................... 500Aac or two X FS which ever is greater to a maximum of 1750A OUTPUT OUTPUT VOLTAGE SIGNAL.................................. 4 to 20mAdc FS (Full Scale) ACCURACY............................................. ±0.5% FS (±0.1mA) Over Temperature Range RIPPLE..................................................... .2% FS Typical RESPONSE (10 to 90%).......................... 100 m-sec max. TEMPERATURE COEFFICIENT............. ±±0.02% FS/°C max. LOAD RESISTANCE (RL) ....................... 250 Ohms Nominal LOAD RESISTANCE RANGE ................. 0 to 1400 Ohms (See Table II) REPEATABILITY..................................... ±0.1% FS CURRENT SIGNAL @ OVERLOAD ....... 30mA Typical PROTECTION .......................................... Reverse Polarity Protected POWER SUPPLYPOWER SUPPLY SUPPLY VOLTAGE (PS) ........................ 15Vdc Nominal CURRENT DRAIN.................................... 20mA SUPPLY VOLTAGE RANGE................... 5 to 35Vdc (See Table II) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE. -20° to +70°C STORAGE TEMPERATURE RANGE..... -55° to +85°C ISOLATION ............................................. Input/Output/Case CONDUCTOR CABLE VOLTAGE.......... 1.5KV max. (5KV with Insul. Cable) CASE........................................................ Molded Plastic meets UL flammability rating 94V-0 WEIGHT .................................................. 1.2 lbs. max.
TABLE IITABLE II SUPPLY (PS) VS LOASUPPLY (PS) VS LOAD RESISTANCE (RL)D RESISTANCE (RL)
SUPPLY LOAD RESISTANCE 10Vdc..................................... 0 to 250 Ohms 15Vdc..................................... 0 to 500 Ohms 20Vdc..................................... 0 to 750 Ohms 25Vdc..................................... 0 to 1000 Ohms 27Vdc..................................... 0 to 1100 Ohms 33Vdc..................................... 0 to 1400 Ohms
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--1006X1006X GG AACAAC
TERMINALS:TERMINALS: 5-40 SCREWS, 3/8” CENTER TO CENTER SPACING, ACCEPTS WIRE SIZES UP TO 14 AWG. AND WIRE LUGS UP TO 9/32” WIDE. RL = VX + (.02)RL VX = 5V RL = 5V + (.02)(1400) = 33Vdc
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC RMS CURRENT TRANSDUCER SERIES S714
PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S714-5 ................................. 0 to 5 S714-150............................. 0 to 150 S714-10 ............................... 0 to 10 S714-200............................. 0 to 200 S714-20 ............................... 0 to 20 S714-250............................. 0 to 250 S714-25 ............................... 0 to 25 S714-300............................. 0 to 300 S714-50 ............................... 0 to 50 S714-400............................. 0 to 400 S714-75 ............................... 0 to 75 S714-500............................. 0 to 500 S714-100 ............................. 0 to 100 S714-600............................. 0 to 600
INPUT RANGE CURRENT RANGE........................................................... See Table Aac FS (Full Scale) CURRENT OVERLOAD CONTINUOUS ......................... 500Aac or two X FS which is greater FREQUENCY RANGE...................................................... 360 TO 440 Hz (60Hz Models available) OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc FS ACCURACY ..................................................................... ±0.5% FS LINEARITY........................................................................ ±0.20% FS RESPONSE TIME (10 TO 90%)....................................... 75 ms max. CREST FACTOR.............................................................. 0 to 5 OUTPUT IMPEDANCE..................................................... 10 Ohms max. OUTPUT RIPPLE ............................................................. 5mV RMS max. OUTPUT LOAD ................................................................ 10K Ohms min. SHORT CIRCUIT.............................................................. Protected TEMPERATURE COEFFICIENT ..................................... ±0.01% FS/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... +14 TO +32Vdc TRANSIENT PROTECTION ............................................ ±60V (t<100ms) CURRENT DRAIN ............................................................ 10mA max. REVERSE POLARITY PROTECTION............................. 100µA max current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -40° to +85°C STORAGE TEMPERATURE............................................ -55° to +85°C OPERATING HUMIDITY .................................................. 0% to 95% RH MOISTURE RESISTANCE............................................... Will meet Method 106 of MIL-STD-202 & Method 507.1, Proc. 1 of MIL-STD-810 ALTITUDE......................................................................... Operating: Sea level to 70,000 ft. RANDOM VIBRATION...................................................... Operating MIL-STD-810E Category 5, Proc. 1, WO=0.012G2Hz, Duration 1 hr., Figure 514.4-8 Suggested Vibration levels for high performance Aircraft 12.5 G-RMS composite DIELECTRIC STRENGTH ............................................... 350V RMS terminals 1-4 to 5 & case INSULATION RESISTANCE ............................................ 100 M-Ohms min. ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. SHOCK.............................................................................. Operating: 50g, 11 m-sec half sine pulse Method 213 Condition A of MIL-STD-202. WEIGHT............................................................................ 1.5 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S714-1006 B AAC
TERMINAL IDENTIFICATION 1- A. SUPPLY VOLTAGE (+) 2- B. SUPPLY (RTN) 3- C. OUTPUT SIGNAL (+) 4- D. OUTPUT (RTN) 5- E. CASE GROUND F. SPARE
MOLDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC RMS CURRENT TRANSDUCER SERIES S786
PART CURRENT PART CURRENT NUMBER RANGE NUMBER RANGE S786-5 ................................. 0 to 5 S786-200............................. 0 to 200 S786-10 ............................... 0 to 10 S786-250............................. 0 to 250 S786-20 ............................... 0 to 20 S786-300............................. 0 to 300 S786-25 ............................... 0 to 25 S786-400............................. 0 to 400 S786-50 ............................... 0 to 50 S786-500............................. 0 to 500 S786-75 ............................... 0 to 75 S786-600............................. 0 to 600 S786-100 ............................. 0 to 100 S786-800............................. 0 to 800 S786-150 ............................. 0 to 150 S786-1000........................... 0 to 1000
INPUT RANGE CURRENT RANGE........................................................... See Table Aac FS (Full Scale) CURRENT OVERLOAD CONTINUOUS ......................... 500Aac or two X FS which is greater FREQUENCY RANGE...................................................... 60 Hz (400Hz Models available) OUTPUT VOLTAGE SIGNAL........................................................... 0 to +5Vdc FS ACCURACY ..................................................................... ±0.5% FS LINEARITY........................................................................ ±0.20% FS RESPONSE TIME (10 TO 90%)....................................... 130 ms typ. CREST FACTOR.............................................................. 0 to 5 OUTPUT IMPEDANCE..................................................... 10 Ohms max. OUTPUT RIPPLE ............................................................. 10mV RMS typ. OUTPUT LOAD ................................................................ 10K Ohms min. SHORT CIRCUIT.............................................................. Protected TEMPERATURE COEFFICIENT ..................................... ±0.01% FS/°C max. POWER SUPPLY SUPPLY VOLTAGE ......................................................... +14 TO +32Vdc TRANSIENT PROTECTION ............................................ ±60V (t<100ms) CURRENT DRAIN ............................................................ 10mA max. REVERSE POLARITY PROTECTION............................. 100µA max current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -40° to +85°C STORAGE TEMPERATURE............................................ -45° to +85°C OPERATING HUMIDITY .................................................. 0% to 95% RH DIELECTRIC STRENGTH ............................................... 1500V RMS terminals 1-5 to case INSULATION RESISTANCE ............................................ 200 M-Ohms min. CONDUCTOR CABLE VOLTAGE ................................... 1.5KV max. (5KV with insulated cable) ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. CASE………………………………………………………… Molded Plastic meets UL Flammability 94V-0 WEIGHT…………………………………………………….. 1.2lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S786-1006 A AAC
TERMINAL IDENTIFICATION 1- SUPPLY VOLTAGE (+) 2- SUPPLY (RTN) 3- OUTPUT SIGNAL (+) 4- OUTPUT (RTN) 5- SPARE
MOLDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS, 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES TO 14 AWG AND WIRE LUGS UP TO 9/32 IN. WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE: MOLDED TERMINAL BARRIER WITH 5-40 TERMINAL SCREWS AND .375 CENTER DISTANCES. TERMINALS ACCEPT WIRE SIZES UP TO #16 AWG. WITH LUGS TO .281 IN. WIDE. ADD –C TO PART NUMBER FOR CONNECTOR OPTION CONNECTOR TYPE MS3112E-10-6P OR EQUIV.
AC RMS CURRENT TRANSDUCER SERIES 1001
REMOVABLE YOKE TYPE
INPUT CURRENT INPUT CURRENT PART NO. AMPS RMS PART NO. AMPS RMS 1001-100 ..................... 0 TO 100 1001-1000................................0 TO 1000 1001-150 ..................... 0 TO 150 1001-1500............................... 0 TO 1500 1001-250 ..................... 0 TO 250 1001-2000............................... 0 TO 2000 1001-500 ..................... 0 TO 500 1001-2500............................... 0 TO 2500 1001-750 ..................... 0 TO 750 1001-3000............................... 0 TO 3000 INPUT RANGE ............................................................................. See Table FREQUENCY ................................................................... DC to 480Hz CREST FACTORS ........................................................... Up to 7 OVERLOAD...................................................................... 2x Range continuously, 10x for 10 sec. OUTPUT VOLTAGE SIGNAL........................................................... 0 to 5Vdc FS (Full Scale) ACCURACY...................................................................... ±1% FS (±50mV) RESPONSE (0 TO 90%) .................................................. 100 m-sec RIPPLE ............................................................................. 25mV RMS @ 60Hz TEMPERATURE COEFFICENT...................................... ±.05% FS/°C max. OUTPUT IMPEDANCE .................................................... 1000 Ohms ±5% OUTPUT PROTECTION.................................................. Output terminals 1 & 2 will withstand ±32Vdc or short circuit continuously POWER SUPPLY SUPPLY VOLTAGE ......................................................... +28Vdc ±4Vdc CURRENT DRAIN............................................................ 100mA max. OVER VOLTAGE PROTECTION .................................... ±35Vdc without damage REVERSE POLARITY PROTECTION ............................ 10µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -25°C to +71°C STORAGE TEMPERATURE RANGE ............................. -55°C to +100°C DIELECTRIC STRENGTH ............................................... 350V RMS (all terminals to case) INSULATION RESISTANCE............................................ 100 M-ohms (all terminals to case) ALTITUDE......................................................................... Operating sea level to 60,000 ft. VIBRATION....................................................................... Operating - 0.06 in. D.A., 10 to 55 Hz method 201 of MIL-STD-202 SHOCK ............................................................................. Operating 50 g, 11 m-sec half sine pulse method 213 Condition A of MIL-STD-202 MOISTURE RESISTANCE .............................................. Will meet method 106 of MIL-STD-202 and method 507.1 Proc. 1 of MIL-STD-810 OPERATING HUMIDITY.................................................. 0% to 95% RH ATTITUDE ........................................................................ Units will perform as specified when mounted in any position WEIGHT ........................................................................... 2 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-1001 J AACAAC
TERMINAL IDENTIFICATION CONNECTOR BARRIER A OUTPUT (+) 1 B OUTPUT (RTN) 2 C SUPPLY VOLTAGE (+) 3 D SUPPLY VOLTAGE (RTN) 4 E SPARE F SPARE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTES: 1. NORMALLY SUPPLIED WITH 5 PIN TERMINAL BARRIER STRIP. MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS, .325 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 16 AWG AND WIRE LUGS TO .250 IN. WIDE. AVAILABLE WITH 6 PIN OPTIONAL CONNECTOR MS3112E-10-6P OR EQUIVALENT. ADD LETTER -C AFTER PART NUMBER FOR CONNECTOR OPTION.
AC RMS CURRENT TRANSDUCER SERIES S461
REMOVABLE YOKE TYPE
INPUT CURRENT INPUT CURRENT PART NO. AMPS RMS PART NO. AMPS RMS S461-100 .....................0 TO 100 S461-1000 ............................... 0 TO 1000 S461-150 .....................0 TO 150 S461-1500 ............................... 0 TO 1500 S461-250 .....................0 TO 250 S461-2000 ............................... 0 TO 2000 S461-500 .....................0 TO 500 S461-2500 ............................... 0 TO 2500 S461-750 .....................0 TO 750 S461-3000 ............................... 0 TO 3000 INPUT RANGE.............................................................................. See Table FREQUENCY .................................................................... DC to 480Hz CREST FACTORS............................................................ Up to 7 OVERLOAD....................................................................... 2X range continuously, 10X for 10 sec. OUTPUT VOLTAGE SIGNAL ........................................................... 0 to 5Vdc (Full Scale) ACCURACY....................................................................... ±1% FS (±50mV) RESPONSE (0 to 90%) ..................................................... 100 m-sec RIPPLE .............................................................................. 25mV RMS @ 60Hz TEMPERATURE COEFFICIENT...................................... ± .05% FS/°C max. OUTPUT IMPEDANCE..................................................... 1000 Ohms ±5% OUTPUT PROTECTION ..................................................Output terminals 1 & 2 will withstand ±32Vdc or short circuit continuously POWER SUPPLY SUPPLY VOLTAGE ......................................................... +28Vdc ±4Vdc CURRENT DRAIN............................................................. 100mA max. OVER VOLTAGE PROTECTION..................................... ±35Vdc without damage REVERSE POLARITY PROTECTION ............................. 10µA max current drain without damage. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .......................... -25°C to +71°C STORAGE TEMPERATURE RANGE.............................. -55°C to +100°C DIELECTRIC STRENGTH................................................ 350V RMS (all terminals to case) INSULATION RESISTANCE ............................................ 100M-Ohms (all terminals to case) ALTITDUE ......................................................................... Operating: sea level to 60,000 ft. VIBRATION ....................................................................... Operating: 0.06 in. D.A., 10 to 55 Hz (Method 201 of MIL-STD-202) SHOCK.............................................................................. Operating: 50g, 11 m-sec half sine pulse Method 213, Condition A of MIL-STD-202. MOISTURE RESISTANCE ............................................... Will meet Method 106 of MIL-STD-202 and Method 507.1 Proc. 1 of MIL-STD-810. OPERATING HUMIDITY................................................... 0% to 95% RH ATTITUDE......................................................................... Unit will perform as specified when mounted in any position. CASE MATERIAL.............................................................. Molded plastic meets UL flammability rating 94V-0 WEIGHT ............................................................................ 12 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S461-1001 A AACAAC
TERMINAL IDENTIFICATION BARRIER CONNECTOR 1 OUTPUT (+) A 2 OUTPUT (RTN) B 3 SUPPLY VOLTAGE (+) C 4 SUPPLY VOLTAGE (RTN) D 5 SPARE E SPARE F
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE:NOTE: MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS, 7/16 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 12 AWG AND WIRE LUGS UP TO 5/16 IN. WIDE
AC CURRENT LEVEL CONTROLLERAC CURRENT LEVEL CONTROLLER SERIES 870SERIES 870
RANGERANGE RANGERANGE PART NO.PART NO. AMPS ACAMPS AC PART NO.PART NO. AMPS ACAMPS AC 870-1............................ 1 870-50 ...................................... 50 870-2............................ 2 870-100 ................................... 100 870-5............................ 5 870-150 ................................... 150 870-10..........................10 870-200 ................................... 200 870-15..........................15 870-250 ................................... 250 870-20..........................20 870-300 ................................... 300 INPUT INPUT CURRENT RANGES (FULL SCALE) .............................. See Table Above FREQUENCY.................................................................... 47 to 63Hz OVERLOAD RATING....................................................... 500A for 30 sec/hr OUTPUT OUTPUT RELAY CONTACT RATINGS .......................................... SPDT; Actuated at set point 10 AMPS @ 250 Vac or 24 Vdc * SET POINT ..................................................................... Adjustable 20 to 100% FS SET POINT REPEATABILITY.......................................... ±0.5% of range RESET............................................................................... Automatic when current falls 20% below set point (typical) SET POINT INDICATOR LIGHT ...................................... On when current is at or above set point
(Relay energized) RESPONSE....................................................................... 500 m-sec (typical) TIME DELAY (OPTIONAL) .............................................. Adjustable 0.5 sec to 15 sec * Set point normally at approx. mid range when shipped from factory. Set point adjusted by factory to desired level upon request. Set point and time delay adjustment- turn clockwise to increase. SUPPLY (AC LINE)SUPPLY (AC LINE) VOLTAGE (STANDARD) ................................................. 115 Vac (105 min. - 130 max.) (OPTIONAL) ................................................... 220 Vac (200 min. - 260 max.) FREQUENCY.................................................................... 47 thru 63 Hz BURDEN ........................................................................... 4Va max. Contact Factory for 440Vac or 400Hz operations. ENVIRONMENTAL AND PHYSICAL SPECIFICATIONENVIRONMENTAL AND PHYSICAL SPECIFICATION OPERATING TEMPERATURE RANGE.......................... -20°C to +70°C ISOLATION....................................................................... Input, Relay, Case DIELECTRIC STRENGTH................................................ 2000V RMS WEIGHT ............................................................................ 2 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--870870 GG AACAAC
TERMINAL IDENTIFICATTERMINAL IDENTIFICATIONION 1-2 AC SUPPLY VOLTAGE 3 CASE GROUND 4-5-6 RELAY CONTACTS
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTE:NOTE: MOLDED TERMINAL BLOCK WITH 6-32 TERMINAL SCREWS, 7/16 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 12 AWG AND WIRE LUGS UP TO 5/16 IN.
AC CURRENT CONTROLLERAC CURRENT CONTROLLER SERIES 871SERIES 871
RANGERANGE RANGERANGE PART NO.PART NO. AMPS ACAMPS AC PART NO.PART NO. AMPS ACAMPS AC 871-1............................1 871-50 ......................................50 871-2............................2 871-100 ................................... 100 871-5............................5 871-150 ................................... 150 871-10..........................10 871-200 ................................... 200 871-15..........................15 871-250 ...................................250 871-20..........................20 871-300 ...................................300 INPINPUT (LOAD CURRENT) UT (LOAD CURRENT) CURRENT RANGES (FULL SCALE) .............................. See Table Above FREQUENCY.................................................................... 47 to 400Hz OVERLOAD...................................................................... 250A for 100AMP FS & below 500A FOR 150 AMP FS & above OUTPUT OUTPUT RELAY .............................................................................. SPDT; Actuated at set point RELAY CONTACT RATINGS .......................................... 10 AMPS @ 250 Vac or 24 Vdc * SET POINT ..................................................................... Adjustable 20 to 100% FS SET POINT REPEATABILITY.......................................... ±0.5% of range RESET............................................................................... Automatic when current falls 20% below set point SET POINT INDICATOR LIGHT ...................................... On when current is at or above set point (Relay energized) RESPONSE....................................................................... 500 m-sec (typical) TIME DELAY (OPTIONAL) .............................................. Adjustable 0.5 sec to 20 sec * Set point normally at mid range when shipped from factory. User desired set point can be factory set upon request. Set point and time delay adjust - turn clockwise to increase. SUPPLY (AC LINE)SUPPLY (AC LINE) VOLTAGE ........................................................................ 115 Vac (105 min. - 130 max.) or 220 Vac (200 min. - 260 max.) or 440 Vac (390 min. - 490 max.) FREQUENCY RANGE...................................................... 47 thru 400 Hz ENVIRONMENTAL AND OTHER SPECIFICATIONSENVIRONMENTAL AND OTHER SPECIFICATIONS OPERATING TEMPERATURE RANGE.......................... -55°C to +85°C ISOLATION....................................................................... Input, Relay, Case DIELECTRIC STRENGTH................................................ 2000V RMS WEIGHT ............................................................................ 2 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--871871 BB AACAAC
TERMINAL IDENTIFICATIONTERMINAL IDENTIFICATION 1-2 AC SUPPLY VOLTAGE 3 CASE GROUND 4-5-6 RELAY CONTACTS
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTES:NOTES: * TRIP POINT SET AT MID RANGE WHEN SHIPPED. SET POINT AND DELAY ADJUSTMENTS - TURN CLOCKWISE TO INCREASE. SET POINT & DELAY ADJUSTED BY FACTORY TO DESIRED LEVELS UPON REQUEST. ** LIGHT EMITTING DIODE (LED) COLOR RED INDICATES THE ON/OFF STATUS OF THE UNIT.
AC CURRENT CONTROLLERAC CURRENT CONTROLLER SERIES 882SERIES 882
CURRENT RANGECURRENT RANGE CURRENT RANGECURRENT RANGE PART NO.PART NO. AMPS ACAMPS AC PART NO.PART NO. AMPS ACAMPS AC 882-1............................ .2 TO 1 882-50...................................... 10 TO 50 882-2............................ .4 TO 2 882-100.................................... 20 TO 100 882-5............................ 1 TO 5 882-150.................................... 30 TO 150 882-10.......................... 2 TO 10 882-200.................................... 40 TO 200 882-15.......................... 3 TO 15 882-250.................................... 50 TO 250 882-20.......................... 4 TO 20 882-300.................................... 60 TO 300 INPUT INPUT CURRENT RANGE........................................................... See Table FREQUENCY .................................................................... 50 to 400Hz OVERLOAD CURRENT CONTINUOUS.......................... 250 Amps or two times range, whichever is greater OVERLOAD CURRENT SURGE ..................................... 10,000 Amps for 6 cycles OUTPUT OUTPUT RELAY CONTACT S.P.D.T. ............................................. Actuated at and above set point SWITCH RATING.............................................................. 2 Amps @ 250Vac or 30Vdc (Resistive Load) * TRIP POINT .................................................................... Adjustable over current range TRIP POINT REPEATABILITY......................................... ±0.5% of range RESET............................................................................... Automatic @ 20% below set point RESPONSE TIME ............................................................. 500 m-sec max. TIME DELAY (OPTIONAL) .............................................. Adjustable 0.500 m-sec to 15 sec. ** INDICATOR................................................................... LED-on at & above trip POWER SUPPLY (AC LINE)POWER SUPPLY (AC LINE) VOLTAGE ........................................................................ 115Vdc VOLTAGE RANGE ........................................................... 105 to 125Vac max. FREQUENCY .................................................................... 47 to 63 Hz BURDEN ........................................................................... 4VA typical ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -20°C to +70°C STORAGE TEMPERATURE RANGE.............................. -40°C to +85°C DIELECTRIC STRENGTH ................................................ 2000V RMS CASE MATERIAL............................................................. Molded plastic meets UL flammability rating 94V-0 WEIGHT ............................................................................ TBD
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--882882 AA AACAAC
DELAY OPTIONDELAY OPTION ADD “-T” TO MODEL NO. FOR THE TIME DELAY OPTION.
TERMINAL BARRIERTERMINAL BARRIER 5-40 SCREWS 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE LUG UP TO 9/32” WIDE.
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT OPERATED SWITCHESAC CURRENT OPERATED SWITCHES SPLIT CORESPLIT CORE
AAC MODELAAC MODEL RANGERANGE ADJUSTABLEADJUSTABLE OUTPUTOUTPUT ACS-CAJ-150 1.5-150A YES NORMALLY CLOSED ACS-OAJ-150 1.5-150A YES NORMALLY OPEN ACS-CNO-250 1.5-250A NO NORMALLY CLOSED ACS-ONO-250 1.5-250A NO NORMALLY OPEN
HOW TO ORDEHOW TO ORDERR ACSACS-- ACS ACS-- RANGE RANGE -150 – 1.5 TO 150A -250 – 1.5 TO 250A OUTPUT OUTPUT -CAJ – ADJUSTABLE – NORMALLY CLOSED -CNO – NON-ADJUSTABLE – NORMALLY CLOSED -OAJ – ADJUSTABLE – NORMALLY OPEN -ONO – NON-ADJUSTABLE – NORMALLY OPEN
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--ACSACS BB AACAAC
SPECIFICATIONSSPECIFICATIONS Power SupplyPower Supply NONE--Self-powered OutputOutput Magnetically Isolated Solid State Switch Output RatingOutput Rating N.O. Version: 0.2A @ 240VAC or VDC N.C. Version: 0.2A @ 130VAC or VDC Not polarity sensitive Off State LeakageOff State Leakage None Response TimeResponse Time 0.120 Second Set Point RangeSet Point Range 1.5-150A HysteresisHysteresis 5% of Setpoint OverloadOverload ModelModel ContinuousContinuous 6 Sec6 Sec 1 Sec1 Sec Normally Open 250A 500A 1000A Normally Closed 150A 400A 1000A Isolation VoltageIsolation Voltage UL Listed to 1,270VAC, tested to 5,000VAC Frequency RangeFrequency Range 6-100Hz Sensing Sensing ApertureAperture 0.85” (21.5mm) sq. CaseCase UL 94V-0 Flammability rated EnvironmentalEnvironmental -58 to 149° F (-50 to 65° C), 0-95% RH, non-condensing ListingListing UL 508 Industrial Control Equipment (USA & Canada); CE
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT OPERATEAC CURRENT OPERATED SWITCHESD SWITCHES SPLIT CORESPLIT CORE
AAC MODELAAC MODEL RANGESRANGES RANGE SELECT.RANGE SELECT. OUTPUTOUTPUT ACS-CAJ-200 1.5-6A YES NORMALLY CLOSED 6-40A 40-200A ACS-OAJ-200 1.5-6A YES NORMALLY OPEN 6-40A 40-200A
HOW TO ORDERHOW TO ORDER ACSACS-- RANGE -200 – 1.5 TO 6A – 6 TO 40A – 40 TO 200A OUTPUT RANGE SELECTABLE -CAJ – NORMALLY CLOSED YES -OAJ – NORMALLY OPEN YES
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--ACSACS--33 BB AACAAC
SPECIFICATIONSSPECIFICATIONS Power SuPower Supplypply NONE--Self-powered OutputOutput Isolated Solid State Switch Output RatingOutput Rating 1.0A @ 240VAC (Standard Units) 15A @ 120VDC, 10A @ 240VDC (-15 Option) Off State LeakageOff State Leakage NO: None NC: 2.5mA Response TimeResponse Time 0.04 to 0.120 Second Set Point RangeSet Point Range 1.5-6, 6-40 & 40-200A HysteresisHysteresis 5% of Setpoint OverloadOverload CurrentCurrent ContinuousContinuous 6 Sec6 Sec 1 Sec1 Sec (11) 1-6A 150A 400A 600A (22) 6-40A 150A 500A 800A (33) 40-200A 210A 800A 1200A IsolaIsolation Voltagetion Voltage UL Listed to 1,270VAC, tested to 5,000VAC Frequency RangeFrequency Range 6-100Hz, works on VFDs Sensing ApertureSensing Aperture 0.85” (21.5mm) sq. CaseCase UL 94V-0 Flammability rated EnvironmentalEnvironmental -58 to 149° F (-50 to 65° C), 0-95% RH, non-condensing ListingListing UL 508 Industrial Control Equipment (USA & Canada); CE
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC CURRENT SWITCHESAC CURRENT SWITCHES SPLIT CORESPLIT CORE
SELFSELF--CALIBRATINGCALIBRATING
AAC MODELAAC MODEL RANGERANGE FUNCTIONFUNCTION OUTPUTOUTPUT ACS-CO-150 2.8-150A OVERLOAD NORMALLY CLOSED ACS-CU-150 2.8-150A UNDERLOAD NORMALLY CLOSED ACS-CB-150 2.8-150A OVER/UNDER NORMALLY CLOSED ACS-OO-150 2.8-150A OVERLOAD NORMALLY OPEN ACS-OU-150 2.8-150A UNDERLOAD NORMALLY OPEN ACS-OB-150 2.8-150A OVER/UNDER NORMALLY OPEN
HOW TO ORDHOW TO ORDERER ACS-XX-150 (2.8A TO 150A –only) -XX FUNCTION OUTPUT -CO OVERLOAD NORMALLY CLOSED -CU UNDERLOAD NORMALLY CLOSED -CB OVER/UNDER NORMALLY CLOSED -OO OVERLOAD NORMALLY OPEN -OU UNDERLOAD NORMALLY OPEN --OB OVER/UNDER NORMALLY OPEN
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--ACSACS--SCSC BB AACAAC
SPECIFICATIONSSPECIFICATIONS Power SupplyPower Supply NONE--Self-powered OutputOutput Magnetically Isolated Solid State Switch Output RatingOutput Rating N.O. Version: 0.2A @ 240VAC or VDC N.C. Version: 0.2A @ 130VAC or VDC Not polarity sensitive Off State LeakageOff State Leakage None Response TimeResponse Time 0.20 Seconds Set Point RangeSet Point Range 2.8-150A Set PointSet Point Overload: +15% of load Underload: -15% of load Operating Window +/- 15% of Setpoint HysteresisHysteresis 5% of Setpoint OverloadOverload ModelModel ContinuousContinuous 6 Sec6 Sec 1 Sec1 Sec ALL 150A 500A 1000A Isolation VoltaIsolation Voltagege UL Listed to 1,270VAC, tested to 5,000VAC Frequency RangeFrequency Range 6-100Hz Sensing ApertureSensing Aperture 0.85” (21.5mm) sq. CaseCase UL 94V-0 Flammability rated EnvironmentalEnvironmental -58 to 149° F (-50 to 65° C), 0-95% RH, non-condensing ListingListing UL 508 Industrial Control Equipment (USA & Canada); CE
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTES:NOTES: * TRIP POINT SET AT MID RANGE WHEN SHIPPED. TURN ADJUSTABLE TRIP POINT DIAL CLOCKWISE TO INCREASE SET POINT LEVEL. SET POINT ADJUSTED BY FACTORY TO DESIRED LEVELS UPON REQUEST. ** LIGHT EMITTING DIODE (LED) COLOR RED INDICATES THE ON/OFF STATUS OF THE UNIT.
AC CURRENT CONTROLLERAC CURRENT CONTROLLER SERIES 881SERIES 881
CURRENT RANGECURRENT RANGE OVERLOAD OVERLOAD MODEL NUMBERMODEL NUMBER AMPS ACAMPS AC AMPS AC AMPS AC 881-12.............................2 - 12 ...........................................250 881-50..................... .......8 - 50 ..........................................250 881-120................... ...40 - 120 ...........................................250 881-250................... .100 - 250 ...........................................300 INPUT INPUT CURRENT RANGE........................................................... See Table FREQUENCY.................................................................... 50 to 400 Hz OVERLOAD CURRENT CONTINUOUS.......................... See Table OVERLOAD CURRENT SURGE..................................... 10,000 Amps for 6 cycles OUTPUT OUTPUT RELAY CONTACT (S.P.D.T.) .......................................... Actuated at and above set point CONTACT RATING.......................................................... 2 Amps @ 250Vac or 3Vdc (Resistive Load) * TRIP POINT.................................................................... Adjustable over current range RESET (AUTOMATIC) ..................................................... 5% of range below trip point typical RESPONSE TIME............................................................. 200 m-sec max. ** INDICATOR................................................................... LED-on at & above trip POWER POWER SUPPLY (AC LINE)SUPPLY (AC LINE) SUPPLY VOLTAGE ........................................................ 115Vac (95 min. - 126 max.) FREQUENCY.................................................................... 47 to 63 Hz BURDEN ........................................................................... 0.9VA ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -20° to +70°C STORAGE TEMPERATURE RANGE ............................. -40° to +85°C DIELECTRIC STRENGTH................................................ 2000V RMS CASE MATERIAL............................................................. Molded plastic meets UL flammability rating 94V-0 WEIGHT ............................................................................ 6 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--881881 CC AACAAC
TERMINAL BARRIERTERMINAL BARRIER 5-40 SCREWS 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE LUG UP TO 9/32” WIDE.
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTES:NOTES: * TRIP POINT SET AT MID RANGE WHEN SHIPPED. TURN ADJUSTABLE TRIP POINT DIAL CLOCKWISE TO INCREASE SET POINT LEVEL. SET POINT ADJUSTED BY FACTORY TO DESIRED LEVELS UPON REQUEST. ** LIGHT EMITTING DIODE (LED) COLOR RED IS IN SERIES WITH THE SOLID STATE SWITCH INDICATES THE ON/OFF STATUS OF THE UNIT.
AC CURRENT CONTROLLERAC CURRENT CONTROLLER SERIES 880BSERIES 880B
CURRENT RANGECURRENT RANGE OVERLOAD OVERLOAD MODEL NUMODEL NUMBERMBER AMPS ACAMPS AC AMPS ACAMPS AC 880B-12....................... 2 – 12 .......................................... 250 880B-50................... .. 8 – 50 ......................................... 250 880B-120 ......................40 – 120 ...................................... 250 880B-250.......................100 – 250 .................................... 300 INPUT INPUT CURRENT RANGE .......................................................... See Table FREQUENCY ................................................................... 50 to 400 Hz OVERLOAD CURRENT CONTINUOUS ......................... See Table OVERLOAD CURRENT SURGE..................................... 10,000 Amps for 6 cycles OUTPUT OUTPUT SOLID STATE SWITCH (S.P.D.T.N.O.)........................... Actuated at and above set point SWITCH RATING ............................................................. 60mA, 120V, ac or dc max. MINIMUM SWITCH VOLTAGE ....................................... 3.5V @ 0.5mA to 4.5V @ 60mA * TRIP POINT.................................................................... Adjustable over current range RESET (AUTOMATIC)..................................................... 5% of range below trip point typical RESPONSE TIME ............................................................ 200 m-sec max. ** INDICATOR .................................................................. LED-on at & above trip point ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE ......................... -20° to +70°C STORAGE TEMPERATURE ........................................... -40° to +85°C DIELECTRIC .................................................................... 2000V RMS CASE MATERIAL ............................................................ Molded plastic meets UL flammability rating 94V-0 WEIGHT............................................................................ 6 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number RRev.ev.
700700--880B880B BB AACAAC
TERMINAL BARRIERTERMINAL BARRIER 5-40 SCREWS 3/8” CENTER TO CENTER SPACING ACCEPTS WIRE LUG UP TO 9/32” WIDE.
Code Ident. No. 15948 AAACAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--S212S212--850850 JJ AACAAC
MATE WITH PT06A-10-65 (SR) (OR EQUIVALENT)
AC CURRENT LEVEL DETECTORAC CURRENT LEVEL DETECTOR PART NUMBER S212PART NUMBER S212--850850
INPUT INPUT RANGE ............................................................................. 0 to 75Aac FREQUENCY ................................................................... 400Hz ±10% OVERLOAD CURRENT CONTINOUSE ......................... 100Aac OVERLOAD CURRENT SURGE..................................... 500Aac for 6 cycles OUTPUT OUTPUT RELAY CONTACT (SPDT) .............................................. Energized at & above set point CONTACT RATING.......................................................... 1 Amp Resistive @ 28V or 5V 400Hz 200mA Inductive 100mA Lamp TRIP POINT(AS CURRENT DECREASES) ................... 0.5Aac ±0.075Aac TRIP POINT REPEATABILITY........................................ ± .01Aac RESET .............................................................................. Automatic when input current rises
approximately 0.1Aac above trip point RESPONSE TIME ............................................................ 200 m-sec max. OUTPUT ISOLATION....................................................... 350V RMS @ sea level POWER SUPPLY POWER SUPPLY SUPPLY VOLTAGE ........................................................ 28Vdc, nominal CURRENT DRAIN............................................................ 70mA max. REVERSE POLARITY PROTECTION ............................ 100µA max. current drain without damage ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE ......................... -55°C to +70°C STORAGE TEMPERATURE RANGE............................. -55°C to +85°C DIELECTRIC STRENGTH ............................................... 350V RMS MIL-STD-202 Method 301 MOUNTING ...................................................................... Rigid in any position INSULATION RESISTANCE............................................ 200 M-Ohms min. MIL-STD-202 Method 302 Test Condition A WEIGHT............................................................................ 16 oz. max. (1 oz mating connector) DO-160 ENVIRONMENT CATEGORY TEMPERATURE & ALTITUDE A2D2 HUMIDITY A VIBRATION CJL EXPLOSION E WATERPROOFNESS X HYDRAULIC FLUID X SAND AND DUST X FUNGUS RESISTANCE F SALT SPRAY S MAGNETIC EFFECT X POWER INPUT (NORMAL OPERATING CONDITIONS ONLY) ABZ VOLTAGE SPIKES AB AUDIO FREQUENCY CONDUCTED SUSCEPTIBILITY Z ELECTROMAGNETIC COMPATIBILITY A
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
A.C. VOLTAGE SENSOR SERIES 108
INPUT VOLTAGE CONTINUOUS
MODEL NO. RANGE Vac OVERLOAD Vac 108-50 ................................ 0 to 50..............................................................100 108-130 ................................ 0 to 130............................................................180 108-150 ................................ 0 to 150............................................................200 108-270 ................................ 0 to 270............................................................380 108-500 ................................ 0 to 500............................................................700 108-600 ................................ 0 to 600............................................................800 INPUT VOLTAGE RANGE................................................................................ See Table FREQUENCY ........................................................................................ 60Hz (400Hz Model Available) * FREQUENCY RANGE .......................................................................... 57 to 63Hz BURDEN................................................................................................ 3mA max. OVERLOAD Vac.................................................................................... See Table OUTPUT VOLTAGE SIGNAL................................................................................ 0 to +5Vdc FS (Full Scale) 4 to 20mA Output Models Available ACCURACY........................................................................................... ±0.5% FS (±25mV) RESPONSE (0 to 90%) ......................................................................... 300 m-sec max. RIPPLE .................................................................................................. 25mV RMS max. TEMPERATURE COEFFICENT........................................................... ±0.02% FS/°C max. REPEATABILITY ................................................................................... ± 0.1% FS OUTPUT IMPEDANCE ......................................................................... 4000 Ohms max. POWER SUPPLY SUPPLY VOLTAGE............................................................................... Self excited ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE............................................... - 20° C to +70°C STORAGE TEMPERATURE RANGE .................................................. - 55°C to +85°C INSULATION RESISTANCE................................................................. 200 M-Ohms (all terminals to case) DIELECTRIC STRENGTH .................................................................... 1000V RMS WEIGHT ................................................................................................ 10 oz. max.
TERMINAL IDENTIFICATION
1. AC VOLTAGE INPUT 2. AC VOLTAGE INPUT 3. OUTPUT (+) 4. OUTPUT (RTN)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-108 J AACAAC
TERMINAL SCREWS 5-40 3/8 CENTER TO CENTER WIRE SIZES TO 14 AWG WIRE LUGS TO .281 WIDE.
* NOTE: ADD SUFFIX -400 TO MODEL NO. FOR 400Hz OPERATION.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
A.C. VOLTAGE TRANSDUCER SERIES 108X
4 TO 20mA 2 WIRE OPERATION
INPUT VOLTAGE CONTINUOUS PART NO. RANGE Vac OVERLOAD Vac
108X-50 ................................ 0 to 50..............................................................100 108X-130 ................................ 0 to 130............................................................180 108X-150 ................................ 0 to 150............................................................200 108X-270 ................................ 0 to 270............................................................380 108X-500 ................................ 0 to 500............................................................700 108X-600 ................................ 0 to 600............................................................800 INPUT VOLTAGE RANGE................................................................................ See Table FREQUENCY ........................................................................................ 60Hz (400Hz Model Available) * FREQUENCY RANGE .......................................................................... 57 to 63Hz BURDEN................................................................................................ 3mA max. OVERLOAD Vac.................................................................................... See Table OUTPUT CURRENT SIGNAL (2 WIRE OPERATION)........................................ 4 to 20mAdc FS (Full Scale) CURRENT SIGNAL @ OVERLOAD..................................................... 30mA typical ACCURACY........................................................................................... ±0.5% FS (±0.1mA) RIPPLE (RMS)....................................................................................... 0.5% FS (±0.1mA RMS) RESPONSE (0 to 90%) ......................................................................... 300 m-sec max. TEMPERATURE COEFFICENT........................................................... ±0.020% FS/°C max. LOAD RESISTANCE (RL)..................................................................... 250 Ohms nominal LOAD RESISTANCE RANGE............................................................... 0 to 1100 Ohms (See Table II) PROTECTION ....................................................................................... Reverse Polarity Protected POWER SUPPLY (PS) SUPPLY VOLTAGE............................................................................... 15Vdc nominal CURRENT DRAIN................................................................................. 20mA SUPPLY VOLTAGE RANGE................................................................. 10 to 35Vdc (See Table II) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE............................................... - 20° C to +70°C STORAGE TEMPERATURE RANGE .................................................. - 55°C to +85°C INSULATION RESISTANCE................................................................. 200 M-Ohms (all terminals to case) DIELECTRIC STRENGTH .................................................................... 1000V RMS WEIGHT ................................................................................................ 10 oz. max.
TERMINAL IDENTIFICATION
1. AC VOLTAGE INPUT 2. AC VOLTAGE INPUT 3. OUTPUT (+) 4. OUTPUT (RTN)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-108X C AACAAC TERMINAL SCREWS 5-40 3/8 CENTER TO CENTER WIRE SIZES TO 14 AWG WIRE LUGS TO .281 WIDE.
* NOTE: ADD SUFFIX -400 TO PART NO. FOR 400Hz OPERATION.
TABLE II SUPPLY (PS) VS LOAD RESISTANCE (RL)
SUPPLY LOAD RESISTANCE 15 Vdc 0 to 250 Ohms 20Vdc 0 to 500 Ohms 25Vdc 0 to 750 Ohms 30Vdc 0 to 1000 Ohms 32Vdc 0 to 1100 Ohms
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
A.C. VOLTAGE SENSOR MODEL S190-108
INPUT VOLTAGE MAXIMUM PART NUMBER RANGES OVERVOLTAGE S190-108-130 0 to 130 Vac 180 Vac S190-108-150 0 to 150 Vac 180 Vac S190-108-270 0 to 270 Vac 380 Vac S190-108-300 0 to 300 Vac 380 Vac S190-108-600 0 to 600 Vac 700 Vac OUTPUT VOLTAGE.............................................................................. 0 to 10Vdc AC INPUT CURRENT DRAIN............................................................... 3mA, max. OUTPUT IMPEDANCE ......................................................................... 10K-Ohms, max. FREQUENCY ........................................................................................ 47 to 63Hz OUTPUT RIPPLE .................................................................................. 3% F.S. RMS, max. ACCURACY........................................................................................... ±2% F.S. REPEATABILITY ................................................................................... ½% F.S. RESPONSE........................................................................................... 200m-sec., max. OPERATING TEMPERATURE............................................................. 0°C to +60°C STORAGE TEMPERATURE ................................................................ -25°C to +85°C TEMPERATURE COEFFICIENT.......................................................... ± 0.05% F.S./°C WEIGHT ................................................................................................ 10 oz.
TERMINAL IDENTIFICATION 1. AC INPUT (HI) 2. AC INPUT (RTN) 3. DC OUTPUT (HI) 4. DC OUTPUT (RTN)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S190-108 D AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC VOLTAGE TRANSDUCER
SERIES V
SELF - POWERED
PART INPUT TRANSIENT OVERLOAD
NUMBER VOLTAGE APPLICATION SEC/HR
V-120....................................0 to 150V ........................... 115/120V ............................. 220V
V-220....................................0 to 300V ........................... 208/220/240V ...................... 375V
V-440....................................0 to 500V ........................... 440/480V ............................. 650V INPUT RANGE ...................................................................................... Vac See Table FREQUENCY ............................................................................ 47 to 1000Hz LINEAR OVER RANGE............................................................. 20% of Range TRANSIENT CAPABILITY ........................................................ See Table DIELECTRIC.............................................................................. 2KV RMS, 60Hz, 1 min. BURDEN.................................................................................... 2VA max. OUTPUT CURRENT SIGNAL................................................................... 0 to 1mA FS (Full Scale) ACCURACY * (60Hz)................................................................. ±0.25% FS (47 to 1000Hz).................................................... ±0.5% FS. RIPPLE ...................................................................................... 0.5% FS peak max. RESPONSE (0 to 99%) ............................................................. 400m-sec. max. LOAD RESISTANCE RANGE................................................... 0 to 11K-Ohms CALIBRATION ADJUSTMENT................................................. ±10% FS STABILITY PER YEAR.............................................................. ±0.1% FS ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE................................................. -20° to +70°C STORAGE TEMPERATURE .................................................... -55° to +85°C ISOLATION................................................................................ Input/Output/Case INSULATION RESISTANCE..................................................... 100m-Ohms min. @ 500Vdc SURGE CAPABILITY ................................................................ IEEE SWC transient test WEIGHT ................................................................................... 16 oz. Typ.
* INCLUDES COMBINED WORSE CASE EFFECTS OF TEMPERATURE AND LOAD CHANGES.
TERMINAL IDENTIFICATION 1. OUTPUT SIGNAL (+) 2. OUTPUT (RTN) 3. AC INPUT 4. AC INPUT
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-V C AACAAC
NOTE: MOLDED TERMINAL BLOCK WITH 8-32 SCREWS 7/16 IN. CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 12 AWG AND LUGS UP TO 3/8 IN. WIDE.
ADD “-E” AND OR “-F” TO PART NUMBER FOR SPECIAL OPTIONS
“-E” OUTPUT VOLTAGE OPTION ADD -E PLUS DESIRED OUTPUT VOLTAGE FROM 0 TO A MAX OF 10
“-F” CALIBRATION FREQ. OPTION ADD -F PLUS DESIRED CALIBRATION FREQ. FROM 47 TO 1000
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC VOLTAGE TRANSDUCER
SERIES VX
4 TO 20mA LOOP - POWERED
PART INPUT TRANSIENT OVERLOAD
NUMBER VOLTAGE APPLICATION SEC/HR
VX-120 .................................0 to 150V ........................... 115/120V ............................. 220V
VX-220 .................................0 to 300V ........................... 208/220/240V ...................... 375V
VX-440 .................................0 to 500V ........................... 440/480V ............................. 650V INPUT RANGE ...................................................................................... Vac See Table FREQUENCY ............................................................................ 47 to 1000Hz LINEAR OVER RANGE............................................................. 20% of Range TRANSIENT CAPABILITY ........................................................ See Table DIELECTRIC.............................................................................. 2KV RMS, 60Hz, 1 min. BURDEN.................................................................................... 2VA max. OUTPUT CURRENT SIGNAL................................................................... 4 to 20mA FS (Full Scale) ACCURACY * (60Hz)................................................................. ±0.25% FS (47 to 1000Hz).................................................... ±0.5% FS. RIPPLE ...................................................................................... 0.5% FS peak max. RESPONSE (0 to 99%) ............................................................. 400m-sec. max. LOAD RESISTANCE................................................................. 250 Ohms Nominal LOAD RESISTANCE RANGE................................................... 0 to 250 Ohms @ 15Vdc 0 to 1100 Ohms @ 32Vdc PROTECTION ........................................................................... Reverse Polarity Protected CALIBRATION ADJUSTMENT................................................. ±10% of FS STABILITY PER YEAR.............................................................. ±0.1% FS max. POWER SUPPLY SUPPLY VOLTAGE................................................................... +15Vdc Nominal CURRENT DRAIN..................................................................... 20mA SUPPLY VOLTAGE RANGE..................................................... 10 to 35Vdc ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE................................................. -20° to +70°C STORAGE TEMPERATURE .................................................... -55° to +85°C ISOLATION................................................................................ Input/Output/Case INSULATION RESISTANCE..................................................... 100m-Ohms min. @ 500Vdc SURGE CAPABILITY ................................................................ IEEE SWC transient test WEIGHT ................................................................................... 16 oz. Typ.
TERMINAL IDENTIFICATION 1. OUTPUT SIGNAL (+) 2. OUTPUT (RTN) 3. AC INPUT 4. AC INPUT
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-VX D AACAAC
NOTE: MOLDED TERMINAL BLOCK WITH 8-32 SCREWS 7/16 IN. CENTER TO CENTER SPACING ACCEPTS WIRE SIZES UP TO 12 AWG AND LUGS UP TO 3/8 IN. WIDE.
ADD “-F” TO PART NUMBER PLUS DESIRED CALIBRATION FREQ. FROM 47 TO 1000Hz FOR CALIBRATION FREQ. OPTION.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC VOLTAGE TRANSDUCER PART NUMBER 101M3-150 INPUT VOLTAGE RANGE ............................................................................. 90 to 150Vac RMS FREQUENCY ................................................................... 60Hz BURDEN........................................................................... 1 Va Typical OVERVOLTAGE CAPABILITY ........................................ 200 Vac max. OUTPUT SIGNAL VOLTAGE SIGNAL (V min. to V max.) ............................. 0 to 5Vdc FS (Full Scale) ACCURACY...................................................................... ±0.5% FS (±25mV) RESPONSE...................................................................... Within 0.5 cycle of input frequency RIPPLE ............................................................................. 1% 50mV RMS max. TEMPERATURE COEFFICIENT..................................... ± 0.08% FS/°C max. (±4mVdc /°c) OUTPUT IMPEDANCE .................................................... 2.5 K-Ohms max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -40° to +70°C STORAGE TEMPERATURE RANGE ............................. -55° to +100°C DIELECTRIC STRENGTH ............................................... 300 V-RMS INSULATION RESISTANCE............................................ 100 M Ohms @ 500Vdc VIBRATION....................................................................... Operating, meet or exceed Method 201A of
MIL-STD-202F and Method 514.3 cat. 4 of MIL-STD-810C.
SHOCK ............................................................................. Operating: 50g, 11 m-sec half sine pulse (meet or exceed method 213B, Condition A of MIL-STD-202F) MOISTURE RESISTANCE .............................................. Meet or exceed Method 106 of MIL-STD-202F and Method 507.2 proc. 1 of MIL-STD-810C. OPERATING HUMIDITY.................................................. 0% to 95% RH WEIGHT ........................................................................... 20 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-101M3 E AAC
TERMINAL IDENTIFICATION
1. A.C. INPUT HI 2. A.C. INPUT LO 3. CASE GROUND 4. OUTPUT (RTN) 5. OUTPUT (+)
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC VOLTAGE TRANSDUCER SERIES 102M3
INPUT VOLTAGE RANGE PART NUMBER V min. V max. 102M3-175........................................... 90 TO 175 102M3-130........................................... 105 TO 130 102M3-225........................................... 175 TO 225 INPUT VOLTAGE RANGE ............................................................................. See Table FREQUENCY ................................................................... 340 to 440Hz BURDEN........................................................................... 1 Va Typical OVERVOLTAGE CAPABILITY ........................................ 200 Vac max. for 175, 130 ranges 300 Vac max. for 225 range OUTPUT SIGNAL VOLTAGE SIGNAL (V min. to V max.) ............................. 0 to 5Vdc FS (Full Scale) ACCURACY...................................................................... ±0.5% FS (±25mV) RESPONSE...................................................................... Within 1 cycle of input frequency RIPPLE ............................................................................. 50mV RMS max. TEMPERATURE COEFFICIENT..................................... ± 0.08% FS/°C max. OUTPUT IMPEDANCE .................................................... 2.5 KOhms max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -40° to +85°C STORAGE TEMPERATURE RANGE ............................. -55° to +100°C DIELECTRIC STRENGTH ............................................... 300 V RMS INSULATION RESISTANCE............................................ 100 MOhms @ 500Vdc VIBRATION....................................................................... Operating, meet or exceed Method 201A of
MIL-STD-202F and Method 514.3 cat. 4 of MIL-STD-810C.
SHOCK ............................................................................. Operating: 50g, 11 m-sec half sine pulse (meet or exceed method 213B, Condition A of MIL-STD-202F) MOISTURE RESISTANCE .............................................. Meet or exceed Method 106 of MIL-STD-202F and Method 507.2 proc. 1 of MIL-STD-810C. OPERATING HUMIDITY.................................................. 0% to 95% RH WEIGHT ........................................................................... 20 oz. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-102M3 E AAC
TERMINAL IDENTIFICATION
1. A.C. INPUT HI 2. A.C. INPUT LO 3. CASE GROUND 4. OUTPUT (RTN) 5. OUTPUT (+)
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
fo
AC VOLTAGE SENSOR MODEL 105
PRESET RANGE (VMAX TO VMIN) MODEL 390 to 490 VRMS -490 455 to 505 VRMS -505 430 to 530 VRMS -530
INPUT LINE FREQUENCY................................................... 57 to 63Hz EXCITATION......................................................................... Self-excited BURDEN................................................................................ 1Va Typical OUTPUT FOR PRESET RANGE ......................................... 0 to 5Vdc OUTPUT IMPEDANCE......................................................... 3K Ohms Max. RESPONSE........................................................................... Within 1 Cycle of Input Frequency RIPPLE .................................................................................. 50Mv rms SUPPRESSION VOLTAGE ACCURACY............................. ± .25% of V Min. RANGE ACCURACY ............................................................ ± 0.5% F.S. Max. TEMPERATURE COEFFICIENT.......................................... ± .08% F.S. per °C TEMPERATURE RANGE ..................................................... -40 to +85 WEIGHT ................................................................................ 20oz. Max. * OTHER PRESET RANGES AVAILABLE
TERMINAL IDENTIFICATION 1. A.C. INPUT HI 2. A.C. INPUT LO 3. CASE GROUND 4. OUTPUT RETURN 5. OUTPUT POSITIVE
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-105 J AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
TERMINAL IDENTIFICATION J1
J1-A. SPARE J1-B. INPUT VOLTS (+/-) J1-C. INPUT VOLTS (+/-)
DC VOLTAGE TRANSDUCER SERIES S657
PART NUMBER RANGE OVERLOAD S657-750 .................................. 0 to ±± 750Vdc ............................... ±± 1500Vdc S657-1200 .................................. 0 to ±± 1200Vdc ............................... ±± 1500Vdc S657-1500 .................................. 0 to ±± 1500Vdc ............................... ±± 2000Vdc INPUT RANGE.............................................................................. See Table OVERLOAD CONTINUOUS............................................. See Table OVERLOAD TRANSIENT................................................. 6Kvdc FOR 100µµ-sec ISOLATION ....................................................................... 5Kv RMS 60Hz FOR 1 min. BURDEN @ FULL SCALE................................................ 3mA typ. for 750V range 4mA typ. for 1200V range 3.3mA typ. for 1500V range OUTPUT CURRENT SIGNAL........................................................... 4 to 20mAdc FS (Full Scale) ACCURACY....................................................................... ±1% FS (±0.2mA max.) over temp. range POLARITY SENSING ....................................................... 4 to 20mAdc proportional to the absolute. Value of the input voltage. RESPONSE (10 to 90%) ................................................... 5m-sec. max. LOAD RESISTANCE......................................................... 250 Ohms nominal LOAD RESISTANCE RANGE .......................................... 0 to 500 Ohms CURRENT SIGNAL @ OVERLOAD ................................ 22mAdc typ. NOISE FILTERING ........................................................... 1 TO 100KHZ ISOLATION MODE REJECTION RATIO ......................... >85db @ 10KHZ POWER SUPPLY SUPPLY VOLTAGE .......................................................... +24 ±±2Vdc CURRENT DRAIN............................................................. 50mA max. TRANSIENT ...................................................................... 60Vdc 5 sec. 100Vdc 1m-sec PROTECTION................................................................... Reverse Polarity Protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ........................................ -40°° to +65°C STORAGE TEMPERATURE ............................................ -40°° to +71°C OPERATION HUMIDITY................................................... 0 to 100% relative humidity SHOCK & VIBRATION...................................................... 20g shock, 10g @ 5-200Hz INSULATION RESISTANCE ............................................ 500M-Ohms @ 500Vdc DIELECTRIC STRENGTH................................................ 1.5Kv RMS 60Hz Continuous. CASE ................................................................................. Thermoplastics Cycolac ABS UL Flammability rating 94V-0. WEIGHT ............................................................................ 1.5 lbs. max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S657 H AACAAC
NOTE: 1. RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT
LOCKWASHER AND # 8 FLAT WASHER. TORQUE MAXIMUM 18 IN-LB.
TRANSDUCER SUPPLIED WITH MATING CONNECTORS AND SOCKET CONTACTS.
TERMINAL IDENTIFICATION J2 J2-A. SUPPLY VOLTS (+) J2-B. OUTPUT SIGNAL (+) J2-C. SUPPLY & OUTPUT (RTN) J2-D. SPARE J2-E. SPARE
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S631 E AACAAC
DC VOLTAGE LEVEL DETECTOR PART NUMBER S631-800
INPUT RANGE .................................................... 0 to + 800Vdc OVERLOAD (CONTINUOUS) ................. 1000Vdc (TRANSIENT) 2000Vdc for 25M-sec. TRIP POINT SET POINT............................................... +375Vdc HYSTERESIS ......................................... Auto reset 10Vdc ±5% below trip point REPEATABILITY...................................... ± 0.5% of 400Vdc (-25 to + 70°C) OUTPUT RELAY CONTACT (SPST) ...................... Actuated at and above trip point CONTACT RATING ................................. 10amp @ 45Vdc RESPONSE ............................................. 110M-sec. MAX. DIELECTRIC STRENGTH ...................... 4000 V RMS coil to contact 1000 V RMS between open contact POWER SUPPLY SUPPLY VOLTAGE ................................ +25 to 45Vdc CURRENT DRAIN.................................... 50mA max. PROTECTION.......................................... Reverse polarity protected ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE ............... -25°C to +75°C STORAGE TEMPERATURE ................... -40°C to +85°C SHOCK & VIBRATION ............................ IAW ADTRANZ Doc. ABB-ES-091291-1 OPERATING HUMIDITY ......................... 0 to 95% Relative Humidity INSULATION RESISTANCE .................. 500 M-ohms @ 500Vdc DIELECTRIC STRENGTH ...................... 3.3Kv RMS 60Hz CASE ........................................................ Thermoplastics Cycolac ABS Meets UL Flammability Rating 94 V-0 WEIGHT .................................................. 1.5 lbs. max.
NOTE: 1. TERMINALS : 1 -- 2 : 6-32 SCREWS TORQUE 8 IN-LB MAX. 3 - 6 : 4-40 SCREWS TORQUE 8 IN-LB MAX. 2. PART TO BE IDENTIFIED WITH ADTRANZ PART NUMBER & REVISION LEVEL IN ACCORDANCE WITH SAE AS478-30, LATEST REVISION. CHARACTER HEIGHT SHALL BE .50 INCH MAX. APPROX. WHERE SHOWN. 3. REFERENCE DOCUMENT NO. E301-010.RFP (XVL). 4. RECOMMENDED MOUNTING HARDWARE #8 SCREW, #8 SPLIT
LOCKWASHER AND # 8 FLAT WASHER. TORQUE MAXIMUM 18 IN-LB.
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
NOTES:NOTES: (1) Includes Combined Worse Case Effects Of Load Changes, Input Current, Voltage And Power Factor. (2) Contact Factory For Available Options. (3) Standard Units Do Not Require An Auxiliary Supply Voltage. (4) Molded Terminal Blocks With 8-32 Terminal Screws And 7/16 Inch Center To Center Spacing. Accepts Wire Sizes Up To No. 12 With Lugs To 3/8 Inch Wide.
WATT & VAR TRANSDUCERWATT & VAR TRANSDUCER SERIES W & QSERIES W & Q
INPUT POWER RANGE .......................................... 0 to Full Scale (FS) See Table I CURRENT RANGE .................................................. 0 to 6.5A RMS - Note (2) (Current Overload 15A Continuous 250A 1 sec/hr) (Current Burden 0.08VA @ 5A) VOLTAGE RANGE (STANDARD)........................... 85 to 140V RMS - Notes (2) & (3) (Voltage Overload 140Vac Continuous) (Voltage Burden 1.5VA @ 120V one phase, all others .04VA/phase) OPTION “B” VOLTAGE RANGE............................ 0 to 150V RMS - Note (2) (Voltage Overload 175Vac Continuous) (Voltage Burden 0.04VA @ 120V) FREQUENCY ........................................................... 60Hz (50 & 400Hz models available) POWER FACTOR RANGE...................................... Any (lead or lag) OUTPUT CURRENT SIGNAL.................................. 0 to ±1mAdc FS - Note (2) ACCURACY ............................................................. ±0.25% FS - Note (1) LOAD RESISTANCE................................................ 0 to 10,000 ohms - Note (2) COMPLIANCE VOLTAGE....................................... 11.5Vdc min. 12.5Vdc typical RIPPLE (Peak to Peak) ........................................... 10µA max. RESPONSE ( 0 to 99%) ........................................... 400 m-sec max. TEMPERATURE COEFFICIENT............................. ±0.005% FS/°C LONG TERM STABILITY......................................... ±0.1% FS/year OUTPUT RANGE ADJUSTMENT ........................... ±3% FS min. - Note (2) (No zero adjustment required) OPTION “B” SUPPLY VOLTAGE........................... 120V RMS Nominal (85 to 140V RMS) SUPPLY BURDEN @ 120V ..................................... 1.5VA max. (0.8PF) SUPPLY FREQUENCY............................................ 60Hz Nominal (55 to 65Hz) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE ................. -20°C to +70°C STORAGE TEMPERATURE RANGE..................... -55°C to +75°C OPERATING HUMIDITY.......................................... 0 to 95% ISOLATION............................................................... Input/Supply/Output/Case DIELECTRIC STRENGTH ....................................... 2000V RMS SURGE CAPABILITY .............................................. IEEE Proposed SWC Test OUTPUT PROTECTION .......................................... Withstand 115Vac 5 minutes standard 1Ma output only SHEET 1 OF 2SHEET 1 OF 2
TABLE ITABLE I
WATTWATT VARVAR FULL SCALEFULL SCALE APPLICATIONAPPLICATION W106 Q106 500W/VAR SIGNAL PHASE W156 Q156 1000W/VAR 3 PHASE 3 WIRE (Balanced Load and Voltage) W206 Q206 1000W/VAR 3 PHASE 3 WIRE (Unrestricted Load and Voltage) W256 Q256 1500W/VAR 3 PHASE 4 WIRE (Unrestricted Load and Balanced Voltage) W306 Q306 1500W/VAR 3 PHASE 4 WIRE (Unrestricted Load and Voltage)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--W & QW & Q EE AACAAC OPTION “B”: SPECIFY OPTION “B” FOR POWER, SYSTEMS WITH ABNORMAL LINE VOLTAGE VARIATIONS. FOR EXAMPLE: W106-B1; Q106-B1; W156-B1; Q156-B1; ……. ECT.
Code Ident. No. 15948 AAAACC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
WATT & VAR TRANSDUCERWATT & VAR TRANSDUCER SERIES W & QSERIES W & Q
TERMINAL CONNECTIONSTERMINAL CONNECTIONS
Hook-Up Diagrams Shown Are Typical Connections For Single And Three Phase Systems In Which Potential Transformers (PT) And Current Transformers (CT) Interface Between Line And Transducer. When The Line Voltage And Current Fall Within The Transducer’s Standard Current And Voltage Range i.e. 0 To 6.5A RMS And 85 To 140V RMS, Then Connections Can Be Made Directly From The Line To The Transducer Without Using PT’s Or CT’s. When The Actual Load Voltage Is Expected To Vary Beyond The Standard Rating Of 85V To 150V RMS, Then A 120Vac Supply Is Necessary Connected To Terminals 7 & 14 As Shown Below. Under These Conditions Option “B” Should Be Specified.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--W & QW & Q EE AACAAC SHEET 2 OF 2
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC WATT TRANSDUCERAC WATT TRANSDUCER
SERIES S73SERIES S73
PARTPART FULL SCALE (FS) CURRENT VOLTAGE SCAL FULL SCALE (FS) CURRENT VOLTAGE SCALE E
FACTOR FACTOR
NUMBERNUMBER POWER RANGEPOWER RANGE RANGE (ac)RANGE (ac) RANGE (ac)RANGE (ac) Vdc/KWVdc/KW
S73-10-115.......................... 0-1KW................................0-10A ...................................0-150V....................... 3.000
S73-25-115.......................... 0-2.5KW.............................0-25A ...................................0-150V....................... 2.000
S73-50-115.......................... 0-5KW................................0-50A ...................................0-150V....................... 1.000
S73-100-115........................ 0-10KW..............................0-100A .................................0-150V....................... 0.500
S73-150-115........................ 0-15KW..............................0-150A .................................0-150V....................... 0.333
S73-200-115........................ 0-20KW..............................0-200A .................................0-150V....................... 0.250
S73-300-115........................ 0-30KW..............................0-300A .................................0-150V....................... 0.167
S73-500-115........................ 0-50KW..............................0-500A .................................0-150V....................... 0.100
S73-10-230.......................... 0-2KW................................0-10A ...................................0-300V....................... 2.500
S73-25-230.......................... 0-5KW................................0-25A ...................................0-300V....................... 1.000
S73-50-230.......................... 0-10KW..............................0-50A ...................................0-300V....................... 0.500
S73-100-230........................ 0-20KW..............................0-100A .................................0-300V....................... 0.250
S73-150-230........................ 0-30KW..............................0-150A .................................0-300V....................... 0.167
S73-200-230........................ 0-40KW..............................0-200A .................................0-300V....................... 0.125
S73-300-230........................ 0-60KW..............................0-300A .................................0-300V....................... 0.083
S73-500-230........................ 0-100KW............................0-500A .................................0-300V....................... 0.050 INPUT INPUT POWER RANGE....................................................................... See Table FREQUENCY............................................................................ 60Hz ±5% BURDEN ................................................................................... 1VA typical POWER FACTOR RANGE ...................................................... 1 to zero (lead or lag) OUTPUT OUTPUT VOLTAGE SIGNAL .................................................................. 0 to +5VdcFS (Full Scale) ACCURACY.............................................................................. ±2% FS (±100mV) RESPONSE............................................................................... 400m-sec max. RIPPLE (PEAK)........................................................................ 2% FS max. TEMPERATURE COEFFICIENT ............................................. ±0.15% FS/°C OUTPUT IMPEDANCE............................................................. 2.5K-Ohms max. P.F. PHASE ANGLE ERROR .................................................. ±3°, max. POWER SUPPLY POWER SUPPLY SUPPLY VOLTAGE ................................................................. 105 to 135Vac FREQUENCY............................................................................ 50/60/400Hz BURDEN ................................................................................... 1VA typical ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.................................. -20° to +60°C STORAGE TEMPERATURE RANGE ..................................... -40° to +85°C DIELECTRIC STRENGTH........................................................ 1000Vac INSULATION RESISTANCE .................................................... 200M-Ohms @ 500Vdc ISOLATION............................................................................... Input/Output/Supply WEIGHT ................................................................................... 3 lbs. Max.
TERMINAL IDENTIFICATIONTERMINAL IDENTIFICATION 1. LOAD POTENTIAL (HI) 2. LOAD POTENTIAL (LO) 3. CASE GROUND 4. OUTPUT (RTN) 5. OUTPUT (+) 6. SUPPLY VOLTAGE 7. SUPPLY VOLTAGE
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--S73S73--413413 CC AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC WATT TRANSDUCER
SERIES 415A
PART 115 Vac CURRENT SCALE FACTOR
NUMBER KW RANGE RANGE (Aac) (V/KW)
415A-10-115 ........................0-1KW................................0-10 ..................................... 5
415A-25-115 ........................0-2.5KW.............................0-25 ..................................... 2
415A-50-115 ........................0-5KW................................0-50 ..................................... 1
415A-100-115 ......................0-10KW..............................0-100 ................................... 0.5
415A-150-115 ......................0-12.5KW...........................0-150 ................................... 0.4
415A-200-115 ......................0-20KW..............................0-200 ................................... 0.25
415A-300-115 ......................0-25KW..............................0-300 ................................... 0.20
415A-500-115 ......................0-50KW..............................0-500 ................................... 0.10
230 Vac
KW RANGE
415A-10-230 ........................0-2KW................................0-10 ..................................... 2.5
415A-25-230 ........................0-5KW................................0-25 ..................................... 1.0
415A-50-230 ........................0-10KW..............................0-50 ..................................... 0.5
415A-100-230 ......................0-20KW..............................0-100 ................................... 0.25
415A-150-230 ......................0-25KW..............................0-150 ................................... 0.20
415A-200-230 ......................0-40KW..............................0-200 ................................... 0.125
415A-300-230 ......................0-50KW..............................0-300 ................................... 0.10
415A-500-230 ......................0-100KW............................0-500 ................................... 0.05 INPUT INPUT POWER RANGE........................................................... See Table VOLTAGE RANGE 115Vac NOMINAL ............................................................. 80 to 150Vac 230Vac NOMINAL ............................................................. 160 to 300Vac BURDEN.................................................................................... 1Va typ. CURRENT RANGE (Aac) ......................................................... See Table FREQUENCY ............................................................................ 60Hz ±5% POWER FACTOR RANGE....................................................... 1 to zero (lead or lag) PF PHASE ANGLE ERROR ..................................................... ±3° max. OUTPUT SIGNAL OUTPUT VOLTAGE ................................................................. 0 to 5Vdc FS (Full Scale) ACCURACY............................................................................... ±2% FS RIPPLE (PEAK)......................................................................... 3% FS max. RESPONSE............................................................................... 400m-sec max. OUTPUT IMPEDANCE............................................................. 2.5K-Ohms max. TEMPERATURE COEFFICIENT.............................................. ±0.2% FS/°C max. SCALE FACTOR (VOLTS/KW) ................................................ See Table ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE .................................. 0° to 50°C STORAGE TEMPERATURE RANGE...................................... -55° to +85°C ISOLATION ............................................................................... Input/Output/Case DIELECTRIC STRENGTH........................................................ 1000V RMS WEIGHT .................................................................................... 1 lb. max,
TERMINAL IDENTIFICATION 1. LOAD POTENTIAL (HI) 2. LOAD POTENTIAL (LO) 3. CASE GROUND 4. OUTPUT (RTN) 5. OUTPUT (+)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-415A D AACAAC
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
TERMINAL IDENTIFICATIONTERMINAL IDENTIFICATION 1. LOAD POTENTIAL (HI) 2. LOAD POTENTIAL (LO) 3. CASE GROUND 4. OUTPUT (RTN) 5. OUTPUT (+)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--416A416A AA AACAAC
AC WATT TRANSDUCER AC WATT TRANSDUCER
SERIES 416A SERIES 416A
PART FULL SCALE (FS) CURRENT VOLTAGE SCALE PART FULL SCALE (FS) CURRENT VOLTAGE SCALE
FACTOR FACTOR
NUMBER NUMBER POWER RANGEPOWER RANGE RANGERANGE RANGERANGE
Vdc/KWVdc/KW
416A-10-440........................ 0-4KW................................0-10A ...................................0-560V....................... 1.25
416A-25-440........................ 0-10KW..............................0-25A ...................................0-560V....................... 0.50
416A-50-440........................ 0-20KW..............................0-50A ...................................0-560V....................... 0.25
416A-100-440...................... 0-40KW..............................0-100A .................................0-560V....................... 0.125
416A-150-440...................... 0-50KW..............................0-150A .................................0-560V....................... 0.100
416A-200-440...................... 0-80KW..............................0-200A .................................0-560V....................... 0.0625
416A-300-440...................... 0-100KW............................0-300A .................................0-560V....................... 0.0500
416A-500-440...................... 0-200KW............................0-500A .................................0-560V....................... 0.0250 INPUT INPUT POWER RANGE....................................................................... KW See Table CURRENT RANGE................................................................... Aac RMS See Table LOAD VOLTAGE RANGE ....................................................... 320 to 560Vac FREQUENCY............................................................................ 60Hz ±5% BURDEN ................................................................................... 1VA typical POWER FACTOR RANGE ...................................................... 1 to zero (lead or lag) OUTPUT OUTPUT VOLTAGE SIGNAL .................................................................. 0 to +5VdcFS (Full Scale) ACCURACY.............................................................................. ±2% FS (±100mV) RESPONSE............................................................................... 400m-sec max. RIPPLE (PEAK) ........................................................................ 3% FS max. TEMPERATURE COEFFICIENT ............................................. ±0.2% FS/°C OUTPUT IMPEDANCE............................................................. 2.5K-Ohms max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.................................. 0° to +50°C STORAGE TEMPERATURE RANGE ..................................... -40° to +85°C DIELECTRIC STRENGTH........................................................ 1000Vac INSULATION RESISTANCE .................................................... 200M-Ohms @ 500Vdc ISOLATION............................................................................... Input/Output/Supply WEIGHT ................................................................................... 3 lbs. Max.
Code Ident. No. 15948 AACAAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-6739
AC WATT TRANSDUCERAC WATT TRANSDUCER
SERIES S217SERIES S217--413413
PART MAX AMPS RANGE PART MAX AMPS RANGE
SCALE(220Vac) SCALE(220Vac)
NUMBERNUMBER (RMS)(RMS) KWKW FACTORFACTOR
V/KWV/KW
S217-10 ............................... 10.......................................0-2KW..................................2.5
S217-25 ............................... 25.......................................0-5KW..................................1.0
S217-50 ............................... 50.......................................0-10KW................................0.50
S217-100 ............................. 100.....................................0-20KW................................0.25
S217-150 ............................. 150.....................................0-25KW................................0.20
S217-200 ............................. 200.....................................0-40KW................................0.125
PART MAX AMPS RANGE SCALE PART MAX AMPS RANGE SCALE
(440Vac)(440Vac)
NUMBERNUMBER (RMS)(RMS) KW KW FACTOR FACTOR
V/KV/KWW
S217-10 ............................... 10.......................................0-4KW..................................1.25
S217-25 ............................... 25.......................................0-10KW................................0.50
S217-50 ............................... 50.......................................0-20KW................................0.25
S217-100 ............................. 100.....................................0-40KW................................0.125
S217-150 ............................. 150.....................................0-50KW................................0.100
S217-200 ............................. 200.....................................0-80KW................................0.0625 INPUT INPUT POWER RANGE....................................................................... KW See Table CURRENT RANGE................................................................... Aac RMS See Table NOMINAL INPUT VOLTAGE................................................... User selects 220Vac to 440Vac LOAD VOLTAGE RANGE ....................................................... 220Vac Nominal 160 to 300Vac 440Vac Nominal 320 to 480Vac FREQUENCY............................................................................ 57 TO 63Hz BURDEN ................................................................................... 1VA typical POWER FACTOR RANGE ...................................................... 1 to zero (lead or lag) OUTPUT OUTPUT VOLTAGE SIGNAL .................................................................. 0 to +5VdcFS (Full Scale) ACCURACY.............................................................................. ±2% FS (±100mV) RESPONSE............................................................................... 400m-sec max. RIPPLE (PEAK) ........................................................................ 3% FS max. P.F. PHASE ANGLE ERROR .................................................. ±3°,max. TEMPERATURE COEFFICIENT ............................................. ±0.2% FS/°C OUTPUT IMPEDANCE............................................................. 2.5K-Ohms max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICSENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.................................. 0° to +50°C STORAGE TEMPERATURE RANGE ..................................... -40° to +85°C
TERMINAL IDENTIFICATIONTERMINAL IDENTIFICATION 1. LOAD POTENTIAL (HI) (440Vac OPERATION ONLY) 2. LOAD POTENTIAL (HI) (220Vac OPERATION ONLY) 3. LOAD POTENTIAL (LO) (220 OR 440Vac OPERATION) 4. OUTPUT (RTN) 5. OUTPUT (+) 6. CASE GROUND
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing NumberDrawing Number Rev.Rev.
700700--S217S217--413413 GG AACAAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
FREQUENCY TRANSDUCER SERIES S350L
PART NO. RANGE (Hz F.S.) PART NO. RANGE (Hz F.S.) S350L-100................... 100 S350L-2K.................................2K S350L-200................... 200 S350L-3K................................ 3K S350L-300................... 300 S350L-5K................................ 5K S350L-500................... 500 S350L-10K.............................. 10K S350L-1K .................... 1K S350L-20K...............................20K AC INPUT FREQUENCY RANGES................................................... See Table SENSITIVITY, MINIMUM.................................................. 20mV RMS 5% to 100% F.S. (sine or sq. wave) SENSITIVITY, MAXIMUM................................................. There shall be no signal output for an input signal of 5mV RMS or less over the frequency range of D.C. to 20KHz PULSE WIDTH................................................................. Minimum duration must equal 20% of the period of the maximum full scale input frequency. IMPEDANCE..................................................................... 5000 Ohms minimum VOLTAGE RANGE........................................................... The max. allowable input voltage is a function of input freq. and is equal to the input freq. divided by 2 (up to a max. of 50V RMS). INPUT ............................................................................... Transformer coupled may be connected either differentially or signal ended. COMMON MODE REJECTION ....................................... 60dB @ 60Hz with input connected differential. OUTPUT VOLTAGE SIGNAL........................................................... 0 to 5Vdc F.S. with 5mA max. current LINEARITY........................................................................ ±0.1% of FS freq. @ 26Vdc power OUTPUT IMPEDANCE .................................................... 1 Ohm max. RIPPLE ............................................................................. <0.1% pk @ F.S. output increasing to approximately 1% pk-pk 1/10 F.S. input freq. ADJUSTMENT.................................................................. A trimpoint adjusts the gains such that a 5Vdc .......................................................................................... max. output may be established for freq. Input ½ F.S. min. LONG TERM STABILITY ................................................. ±0.2% F.S. per year RESPONSE...................................................................... 30/F where F is the max. F.S. freq. To 63% TEMPERATURE COEFFICIENT..................................... ±0.01%/°C of F.S. freq. POWER SUPPLY SUPPLY VOLTAGE ......................................................... +22 to 30Vdc @ 120mA max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE........................................ -48°C to +74°C STORAGE TEMPERATURE ........................................... -55°C to +85°C ISOLATION....................................................................... Input/Output/Power/Case INSULATION RESISTANCE............................................ 100M-Ohms @ 500Vdc VIBRATION....................................................................... 6g RMS 20Hz to 2KHz ALTITUDE......................................................................... Sea Level to 80,000 ft. WEIGHT ........................................................................... 3 lbs. Max. FINISH .............................................................................. Orange paint per FED-STD-595 No. 12197 or equiv.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S350L D AAC
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
FREQUENCY TRANSDUCER
SERIES S343
PART NO. VOLTAGE RANGE OVERLOAD BURDEN S343-120 102 to 127 Vac 140 Vac max. 1.5 VA @ 120V S343-220 200 to 250 Vac 280 Vac max. 1.5VA @ 220V OUTPUT VOLTAGE SIGNAL................................................................................ 0Vdc @ 360Hz to 5Vdc @ 440Hz ACCURACY........................................................................................... ±1.0% FS (±.05V) RIPPLE AND NOISE (BROADBAND) .................................................. 25mV RMS; 50mV peak max. RESPONSE (0 to 99%) ......................................................................... 250mS max. TEMPERATURE ERROR ..................................................................... ±1Hz max. (-20°C to 70°C) ±1.3Hz max. (-40°C to 70°C) IMPEDANCE.......................................................................................... 100 Ohms max. RANGE ADJUSTMENT ........................................................................ ±3% F max. (±150mV) ZERO ADJUSTMENT ........................................................................... ±3% F max. (±150mV) ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE............................................... -40°C to +70°C STORAGE TEMPERATURE RANGE .................................................. -55°C to +85°C VIBRATION............................................................................................ 6g RMS, 20Hz to 2KHz ALTITUDE.............................................................................................. -1000 ft. to 60,000 ft. DIELECTRIC STRENGTH @ SEA LEVEL........................................... 1200Vac, 400Hz (all pins to case except case ground pin) INPUT/OUTPUT ISOLATION ............................................................... 50M-Ohms @ 50Vdc WEIGHT ................................................................................................ 28 oz. max. FINISH HOUSING ................................................................................. Orange paint per FED-STD-595 Number 12197 or equivalent. IDENTIFICATION .................................................................................. Each unit shall be identified with MFR’s P/N, MFR’s S/N and GAC P/N 90SCAE28401-* AAC P/N GAC P/N S343-120 90SCAE28401-1
TERMINAL IDENTIFICATION A. AC INPUT B. AC INPUT (RTN) C. CASE GROUND D. OUTPUT SIGNAL (+) E. OUTPUT SIGNAL (RTN) F. SPARE
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-S343 G AAC
DC CURRENT SENSOR SERIES 904B
PART NO. CURRENT RANGE PART NO. CURRENT RANGE 904B-L01 ....................0 TO 100uA 904B-L1 .................................. 0 TO 1mA 904B-L02 ....................0 TO 200uA 904B-L2 ................................. 0 TO 2mA 904B-L05 ....................0 TO 500uA 904B-L5 ................................. 0 TO 5Ma INPUT CURRENT RANGES....................................................... See Table INPUT RESISTANCE...................................................... 10 Ohms max. ISOLATION (Input to Output) .......................................... 500Vdc max. OUTPUT VOLTAGE SIGNAL.......................................................... 0 to +5.0Vdc FS (Full Scale) ACCURACY..................................................................... ±1% FS RIPPLE............................................................................ 2% FS RMS IMPEDANCE ................................................................... 1000 Ohms ±5% RESPONSE (10 to 90%) ................................................. 50 m-sec. max. TEMPERATURE COEFFICIENT..................................... ±0.04% FS/°C POWER SUPPLY SUPPLY VOLTAGE ........................................................ +28Vdc ±4Vdc CURRENT DRAIN........................................................... 50mAdc max. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.......................... -55°C to +85°C STORAGE TEMPERATURE RANGE ............................. -60°C to +100°C INSULATION RESISTANCE ........................................... 100 M-ohms (all terminals to case) DIELECTRIC STRENGTH............................................... 350V RMS (all terminals to case) ALTITUDE ....................................................................... Operating sea level to 60,000 ft. VIBRATION ..................................................................... Operating - 0.06 in. D.A., 10 to 55 Hz method 201 of MIL-STD-202 SHOCK............................................................................ Operating 50 g, 11 m-sec half sine pulse method 213 Condition A of MIL-STD-202 MOISTURE RESISTANCE.............................................. Will meet method 106 of MIL-STD-202 and method 507.1 Proc. 1 of MIL-STD-810 OPERATING HUMIDITY ................................................. 0% to 95% RH ATTITUDE ....................................................................... Meets spec. for any mounting position WEIGHT .......................................................................... 1.25 lbs. Max.
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ± .010
Drawing Number Rev.
700-904B G AAC
TERMINAL IDENTIFICATION
A. SUPPLY VOLTAGE (+) B. SUPPLY AND OUTPUT (RTN) C. OUTPUT SIGNAL (+) D. CURRENT INPUT (+) E. CURRENT (RTN) F. CASE GROUND
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(631) 694-5100 Fax:(631) 694-673 9
A.C.CURRENT SENSOR SERIES 1003AM2-B
OUTPUT
MODEL NO. INPUT CURRENT IMPEDANCE 1003AM2-10-B ....................... 0 to 10Aac......................................................... 7 1003AM2-15-B ....................... 0 to 15Aac......................................................... 5 1003AM2-20-B ....................... 0 to 20Aac...................................................... 3.5 1003AM2-25-B ....................... 0 to 25Aac...................................................... 3.0 1003AM2-30-B ....................... 0 to 30Aac...................................................... 2.5 1003AM2-50-B ....................... 0 to 50Aac...................................................... 1.5 1003AM2-75-B ....................... 0 to 75Aac...................................................... 1.0 1003AM2-100-B ..................... 0 to 100Aac.................................................... 0.7 1003AM2-125-B ..................... 0 to 125Aac.................................................... 0.6 1003AM2-150-B ..................... 0 to 150Aac.................................................... 0.5 1003AM2-200-B ..................... 0 to 200Aac.................................................... 0.4 1003AM2-250-B ..................... 0 to 250Aac.................................................... 0.3 1003AM2-300-B ..................... 0 to 300Aac.................................................. 0.25 INPUT CURRENT RANGE ............................................................................. See Table FREQUENCY ...................................................................................... 57 to 63Hz OVERLOAD......................................................................................... 500Aac Continuous OUTPUT VOLTAGE SIGNAL.............................................................................. 0 to 5Vdc FS (Full Scale) ACCURACY......................................................................................... ± 1% FS RIPPLE................................................................................................ 3% FS RMS IMPEDANCE ....................................................................................... K Ohms See Table REPEATABILITY................................................................................. 0.5% FS RESPONSE......................................................................................... 150 m-sec TEMPERATURE COEFFICIENT......................................................... ± 0.04% FS/ °C OUTPUT SIGNAL @ OVERLOAD ..................................................... 11Vdc max. POWER SUPPLY SUPPLY VOLTAGE............................................................................. None, self excited ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE.............................................. - 20° C to 70°C STORAGE TEMPERATURE RANGE ................................................. - 55°C to 85°C ISOLATION.......................................................................................... Input/Output/Case INSULATION RESISTANCE ............................................................... 100 M-Ohms WEIGHT .............................................................................................. 1.25 lbs. max.
TERMINAL IDENTIFICATION
1. OUTPUT SIGNAL (+) 2. OUTPUT SIGNAL (RTN)
Dimensions in Inches, Tolerances: .XX ± .03 .XXX ±
Drawing Number Rev.
700-1003AM2-B E AAC
MOLDED TERMINAL BLOCK WITH 5-40 TERMINAL SCREWS 3/8 IN. CENTER TO CENTER SPACING. ACCEPTS WIRE SIZES UP TO 14 AWG & WIRE LUGS UP TO 9/32 IN. WIDE.
Code Ident. No. 15948 AAC American Aerospace Controls Inc., 570 Smith Street, Farmingdale, New York 11735 Tel:(516) 694-5100 Fax:(516) 694-6739
