Altera CD Installation Guide · Installing the GNU Tools and Excalibur Component Software ... development and Altera partner kits. ... Altera CD Installation Guide 9

Altera CD Installation GuideP25-06810-06BlackPMS 877 SilverAltera Blue (replaces PMS 301 Blue)PMS 541 Blue

Altera Corporation101 Innovation DriveSan Jose, California 95134 USAwww.altera.comwww.altera.com/mysupport P25-06810-06

Altera® CD Installation Guide

Altera CD Installation GuideQuartus II Software Version 4.0 Revision 1January 2004 P25-06810-06

Altera, the Altera logo, Nios, Quartus, Quartus II, and the Quartus II logo are registered trademarks, and Excalibur is a trademark of Altera Corporation in the United States and other countries.

Altera acknowledges the trademarks of other organizations for their respective products or services mentioned in this document, including the following: ARM and the ARM Powered logo are registered trademarks of ARM Limited. Mentor Graphics and ModelSim are registered trademarks, and Model Technology is a trademark of Mentor Graphics Corporation.

Copyright © 1990–2004 Altera Corporation and its Licensors. All Rights Reserved.

By using the programs on the Altera CD-ROMs that are enclosed in your Altera package, you indicate that you have read and accepted the terms of the Altera software license agreement.

Altera CD Installation Guide 1

Altera CD Installation Guide Contents

Altera Software CD-ROMs Supported by this Guide ...................................................................................2Installing the Quartus II Software on PCs .....................................................................................................3Installing the Quartus II Software on Solaris Workstations .......................................................................5Installing the Quartus II Software on Linux Workstations ..........................................................................7Installing the Quartus II Software on HP-UX Workstations........................................................................9Installing the GNU Tools and Excalibur Component Software............................................................... 11

Installing the GNU Tools and Excalibur Component Software on PCs....................................... 11Installing the GNU Tools and Excalibur Component Software on Solaris Workstations......... 12Installing the GNU Tools and Excalibur Component Software on Linux Workstations ........... 14Installing the GNU Tools and Excalibur Component Software on HP-UX Workstations ......... 16

Installing the Model Technology ModelSim Software .............................................................................. 19Installing the Model Technology ModelSim Software on PCs ...................................................... 19Installing the Model Technology ModelSim Software on Solaris Workstations ........................ 20Installing the Model Technology ModelSim Software on Linux Workstations........................... 21Installing the Model Technology ModelSim Software on HP-UX Workstations......................... 22

Altera Technical Support................................................................................................................................ 24Altera Product Information............................................................................................................................ 24Obtaining a License File................................................................................................................................. 25

2 Altera Corporation

Altera Software CD-ROMs Supported by this Guide

The installation instructions in this guide apply to the following software CD-ROM versions (some listed CD-ROMs may not be included in your current Altera® package):

■ Quartus® II Design Software for PCs Version 4.0■ Quartus II Design Software for UNIX Workstations (Solaris 7 and 8 Only)

Version 4.0■ Quartus II Design Software for Linux Workstations (Red Hat Linux 7.3 and 8.0 Only)

Version 4.0■ Quartus II Design Software for UNIX Workstations (HP-UX 11.0 Only) Version 4.0■ GNU Tools and Excalibur™ Component Software Version 4.0:

– GNU Tools for ARM® processors– Excalibur Component Software for SOPC Builder Tool

■ Altera VHDL & Verilog HDL Simulation Tool for Use with the Quartus II Software, which includes Model Technology™ ModelSim® Software Version 5.7e


Installing the Quartus II Software on PCs

You can install the Quartus® II software on PCs running Microsoft Windows NT 4.0 (Service Pack 3 or later), Windows 2000, or Windows XP. Before installing the Quartus II software or any Altera® programming hardware, you should read the Quartus II readme.txt file, which provides information on Quartus II software and operating requirements, including disk space and memory. You should also refer to the Quartus II Installation & Licensing for PCs manual and the Quartus II Software Release Notes (www.altera.com/literature/rn/rn_qts.pdf) for more information.

To install the Quartus II software on a PC, follow these steps:

1. Insert the Quartus II Design Software for PCs CD-ROM into your CD-ROM drive.2. Click Install Quartus II Software and Related Software to install the Quartus II

software.

or

If the Quartus II software CD-ROM is in your CD-ROM drive, and the Setup program is not running, you can start it manually. Choose Run (Start menu) and type the following command:

<CD-ROM drive>:\install.exe r

The Setup program starts automatically and guides you through the installation process. If necessary, you can run the Setup program again to install additional features of the software.


1 The Setup program also allows you to install the GNU Tools and Excalibur™ Component software and the Model Technology™ ModelSim®-Altera software. The CD-ROMs for this software are included in the Quartus II subscription packages, but may not be included in the Altera development and Altera partner kits. To install these programs, you must turn on the GNU Tools and Excalibur Component or the ModelSim-Altera options in the Setup program. If you decide to install these programs at another time, refer to “Installing the GNU Tools and Excalibur Component Software on PCs” on page 11 and “Installing the Model Technology ModelSim Software on PCs” on page 19.


Installing the Quartus II Software on Solaris Workstations

You can install the Quartus® II software on a Sun Ultra workstation running Solaris 7 or 8. Before you install the Quartus II software or any Altera® programming hardware, you should read the Quartus II readme.txt file, which provides information on Quartus II software and operating requirements, including disk space, memory, and required operating system patches. You should also refer to the Quartus II Installation & Licensing for UNIX and Linux Workstations manual and the Quartus II Software Release Notes (www.altera.com/literature/rn/rn_qts.pdf) for more information.

1 Your workstation must have an ISO 9660 CD-ROM drive.

To install the Quartus II software on a Solaris workstation, follow these steps:

1. Insert the Quartus II Design Software for UNIX Workstations (Solaris 7 and 8 Only) CD-ROM into your CD-ROM drive.

2. If you are running Volume Manager, the CD-ROM will be automatically mounted as /cdrom/cdrom0, and you must type only the last command below. Otherwise, you must be logged in as a superuser, and you must type all three of the following commands:

mkdir /cdrom/cdrom0 r/sbin/mount -F hsfs -o ro /dev/dsk/<device name of CD-ROM>

/cdrom/cdrom0 r/cdrom/cdrom0/install r

You are guided through the installation procedure.


3. When installation is complete, type the following command at the command prompt:

/sbin/umount /cdrom/cdrom0 r

4. To install the GNU Tools and Excalibur™ Component software, insert the GNU Tools and Excalibur Component Software CD-ROM into your CD-ROM drive.

5. Repeat steps 2 and 3 to install the GNU Tools and Excalibur Component software. However, for the last command in step 2, you should type the following command:

/cdrom/cdrom0/install.sh r

6. To install the Model Technology™ ModelSim®-Altera software, insert the Altera VHDL & Verilog HDL Simulation Tool for Use with the Quartus II Software (Model Technology ModelSim Software) CD-ROM into your CD-ROM drive.

7. Repeat steps 2 and 3 to install the ModelSim-Altera software. However, for the last command in step 2, you should type the following command:

/cdrom/cdrom0/unix/install.ms r

If you decide to install the GNU Tools and Excalibur Component software or the Model Technology ModelSim-Altera software at another time, refer to “Installing the GNU Tools and Excalibur Component Software on Solaris Workstations” on page 12 or “Installing the Model Technology ModelSim Software on Solaris Workstations” on page 20.


Installing the Quartus II Software on Linux Workstations

You can install the Quartus® II software on a PC running Red Hat Linux version 7.3 or 8.0. Before you install the Quartus II software or any Altera® programming hardware, you should read the Quartus II readme.txt file, which provides information on Quartus II software and operating requirements, including disk space, memory, and required operating system patches. You should also refer to the Quartus II Installation & Licensing for UNIX and Linux Workstations manual and the Quartus II Software Release Notes (www.altera.com/literature/rn/rn_qts.pdf) for more information.

1 You must be logged in as a superuser.

To install the Quartus II software on a Linux workstation, follow these steps:

1. Insert the Quartus II Design Software for Linux Workstations (Red Hat Linux Version 7.3 and 8.0 Only) CD-ROM into your CD-ROM drive.

2. Type the following commands at the command prompt:

mkdir /mnt/cdrom r/bin/mount /mnt/cdrom r/mnt/cdrom/install r




/bin/umount /mnt/cdrom r



/mnt/cdrom/install.sh r



/mnt/cdrom/unix/install.ms r

If you decide to install the GNU Tools and Excalibur Component software or the Model Technology ModelSim-Altera software at another time, refer to “Installing the GNU Tools and Excalibur Component Software on Linux Workstations” on page 14 or “Installing the Model Technology ModelSim Software on Linux Workstations” on page 21.


Installing the Quartus II Software on HP-UX Workstations

You can install the Quartus® II software on an HP 9000 Series 700/800 workstation running HP-UX 11.0 with ACE dated November, 1999 or later. Before you install the Quartus II software or any Altera® programming hardware, you should read the Quartus II readme.txt file, which provides information on Quartus II software and operating requirements, including disk space, memory, and required operating system patches. You should also refer to the Quartus II Installation & Licensing for UNIX and Linux Workstations manual and the Quartus II Software Release Notes (www.altera.com/literature/rn/rn_qts.pdf) for more information.

1 Your workstation must have an ISO 9660 CD-ROM drive, and you must be logged in as a superuser.

To install the Quartus II software on an HP-UX workstation, follow these steps:

1. Insert the Quartus II Design Software for UNIX Workstations (HP-UX 11.0 only) CD-ROM into your CD-ROM drive.


mkdir /cdrom r/sbin/mount -o cdcase /dev/dsk/<device name of CD-ROM>

/cdrom r/cdrom/install r




/sbin/umount /cdrom r



/cdrom/install.sh r



/cdrom/unix/install.ms r

If you decide to install the GNU Tools and Excalibur Component software or the Model Technology ModelSim-Altera software at another time, refer to “Installing the GNU Tools and Excalibur Component Software on HP-UX Workstations” on page 16 or “Installing the Model Technology ModelSim Software on HP-UX Workstations” on page 22.


Installing the GNU Tools andExcalibur Component Software

You can install the GNU Tools for ARM® processors and the Excalibur™ Component for SOPC Builder Tool on PCs running Windows NT 4.0, Windows 2000, or Windows XP; or on UNIX workstations running Solaris 7 or 8 or HP-UX 11.0; or on Linux workstations running Red Hat Linux version 7.3 or 8.0. Before installing the GNU Tools and Excalibur Component software, you should read the readme.txt file, which provides information on installation and on software and operating requirements, including disk space and memory.

Installing the GNU Tools andExcalibur Component Software on PCs

To install the GNU Tools and Excalibur Component software on a PC, follow these steps:

1. Insert the GNU Tools and Excalibur Component Software CD-ROM into your CD-ROM drive.

2. Choose Run (Start menu) and type the following command:

<CD-ROM drive>:\windows\setup.exe r

The Setup program starts automatically and guides you through the installation process.


Installing the GNU Tools andExcalibur Component Software on Solaris Workstations

To install the GNU Tools and Excalibur Component software on a Sun Ultra workstation running Solaris 7 or 8, follow these steps:





/cdrom/cdrom0 r/cdrom/cdrom0/install.sh r

If you have previously mounted and unmounted this CD-ROM, a number may be appended to the device name of the CD-ROM, in which case you should use the complete name and number for <device name of CD-ROM>. For example, if the device name appears as SOPC_281#2, use that name.





4. Add the following lines to your .login or .cshrc file:

setenv SOPC_BUILDER_PATH <Excalibur Component system directory>setenv ALTERA_ARM9GP_VER arm9-020528setenv ALTERA_ARM9GP_ROOT /<Excalibur Component system

directory>/bin/arm-gnuprosetenv PATH $ALTERA_ARMGP_ROOT/$ALTERA_ARM9GP_VER/

BIN:$PATH

The default location for the Excalibur Component system directory is usually /usr/altera/kits/xa; if you use a different directory path, you must substitute the correct path name for <Excalibur Component system directory>.

5. If you are planning to use the Model Technology™ ModelSim® simulation software with the Quartus® II software and the Excalibur Component software, add the following lines to your .login or .cshrc file:

setenv MG_ROOT /<Quartus II software system directory>/eda/sim_lib/excalibur/stripe_model_solaris/ModelGen/manager

setenv MG_LIB /<Quartus II software system directory>/eda/sim_lib/excalibur/stripe_model_solaris/ModelGen/manager/SunOS5/MM


setenv MG_MODEL_PATH /<Quartus II software system directory>/eda/sim_lib/excalibur/stripe_model_solaris/ModelGen/models

setenv LMC_HOME /<Quartus II software system directory>/eda/sim_lib/excalibur/swift

setenv PATH "$PATH": /<Quartus II software system directory>/eda/sim_lib/excalibur/swift/lib/sun4Solaris.lib

setenv MG_MODEL_REV r0setenv LMC_CONFIG /<Quartus II software system directory>/eda/

sim_lib/excalibur/swift/data/solaris.lmc

The default location for the Quartus II software system directory is usually /usr/quartus; if you use a different directory path, you must substitute the correct path name for <Quartus II software system directory>.

1 For additional information about installing the ModelSim software, refer to “Installing the Model Technology ModelSim Software” on page 19.

Installing the GNU Tools andExcalibur Component Software on Linux Workstations

To install the GNU Tools and Excalibur Component software on a Linux workstation running Red Hat Linux version 7.3 or 8.0, follow these steps:





mkdir /mnt/cdrom r/bin/mount /mnt/cdrom r/mnt/cdrom/<device name of CD-ROM>/install.sh r







directory>/bin/arm-gnupro


setenv PATH $ALTERA_ARMGP_ROOT/$ALTERA_ARM9GP_VER/BIN:$PATH


Installing the GNU Tools andExcalibur Component Software on HP-UX Workstations

To install the GNU Tools and Excalibur Component software on an HP 9000 Series 700/800 workstation running HP-UX 11.0, follow these steps:





/cdrom r/cdrom/install.sh r








directory>/bin/arm-gnuprosetenv PATH $ALTERA_ARMGP_ROOT/$ALTERA_ARM9GP_VER/

BIN:$PATH



5. If you are planning to use the Model Technology ModelSim simulation software with the Quartus II software and the Excalibur Component software, add the following lines to your .login or .cshrc file:

setenv MG_ROOT /<Quartus II software system directory>/eda/sim_lib/excalibur/stripe_model_hpux/ModelGen/manager

setenv MG_LIB /<Quartus II software system directory>/eda/sim_lib/excalibur/stripe_model_hpux/ModelGen/manager/HPUX/MM

setenv MG_MODEL_PATH /<Quartus II software system directory>/eda/sim_lib/excalibur/stripe_model_hpux/ModelGen/models

setenv LMC_HOME /<Quartus II software system directory>/eda/sim_lib/excalibur/swift

setenv PATH "$PATH": /<Quartus II software system directory>/eda/sim_lib/excalibur/swift/lib/hp700.lib

setenv MG_MODEL_REV r0

The default location for the Quartus II software system directory is usually /usr/quartus; if you use a different directory path, you must substitute the correct path name for <Quartus II software system directory>.

1 For additional information about installing the ModelSim software, refer to “Installing the Model Technology ModelSim Software” on page 19.


Installing the Model Technology ModelSim Software

You can install the Model Technology™ ModelSim® software on PCs running Windows NT 4.0, Windows 2000, or Windows XP; or on UNIX workstations running Solaris 7 or 8 or HP-UX 11.0; or on Linux workstations running Red Hat Linux version 7.3 or 8.0. The ModelSim-Altera® readme files in the modelsim directory on the CD-ROM provide information on ModelSim-Altera software operating requirements and licensing. You should read the appropriate readme file before installing the ModelSim-Altera software.

Installing the Model Technology ModelSim Software on PCs

To install the ModelSim-Altera software on a PC, follow these steps:

1. Insert the Altera VHDL & Verilog HDL Simulation Tool for Use with the Quartus® II Software (Model Technology ModelSim Software) CD-ROM into your CD-ROM drive.

2. Choose Run (Start menu) and type the following command:

<CD-ROM drive>:\modelsim\pc\modelsim-altera.exe r

The Setup program starts automatically and guides you through the installation process.


Installing the Model TechnologyModelSim Software on Solaris Workstations

To install the ModelSim-Altera software on a Sun Ultra workstation running Solaris 7 or 8, follow these steps:


1. Insert the Altera VHDL & Verilog HDL Simulation Tool for use with the Quartus II Software (Model Technology ModelSim Software) CD-ROM into your CD-ROM drive.



/cdrom/cdrom0 r/cdrom/cdrom0/unix/install.ms r

If you have previously mounted and unmounted this CD-ROM, a number may be appended to the device name of the CD-ROM, in which case you should use the complete name and number for <device name of CD-ROM>. For example, if the device name appears as modelsim, use that name.


You are guided through the installation procedure. The installation procedure prompts you to enter the platform of the workstation where you are installing the ModelSim-Altera software.



Installing the Model TechnologyModelSim Software on Linux Workstations

To install the ModelSim-Altera software on a Linux workstation running Red Hat Linux version 7.3 or 8.0, follow these steps:


1. Insert the Altera VHDL & Verilog HDL Simulation Tool for Use with the Quartus II Software (Model Technology ModelSim Software) CD-ROM into your CD-ROM drive.


mkdir /mnt/cdrom r/bin/mount /mnt/cdrom r/mnt/cdrom/unix/install.ms r






Installing the Model TechnologyModelSim Software on HP-UX Workstations

To install the ModelSim-Altera software on an HP 9000 Series 700/800 workstation running HP-UX 11.0, follow these steps:


1. Insert the Altera VHDL & Verilog HDL Simulation Tool for Use with the Quartus II Software (Model Technology ModelSim Software) CD-ROM into your CD-ROM drive.




/cdrom r/cdrom/unix/install.ms r






Altera Technical Support

For technical support, you can visit the Altera® web site or mySupport web site, or you can call the Altera Applications Department.

.

Altera Product Information

For the latest Altera product information or literature, refer to the Literature section of the Altera web site at www.altera.com/literature.

Altera web site www.altera.com(includes the Altera Find Answers page, which is available from the Support Center section of the Altera web site at www.altera.com/answers.)

mySupport web site www.altera.com/mysupport(allows you to submit, view, and update technical support service requests)

Telephone (800) 800-EPLD7:00 a.m. to 5:00 p.m. Pacific time, M–F(408) 544-70007:00 a.m. to 5:00 p.m. Pacific time, M–F


Obtaining a License File

You must have a valid, unexpired Altera® license file in order to use the Altera software provided in this package. If you need to obtain a license file, follow these steps:

1. Point your web browser to the Altera web site at www.altera.com.2. Click the Licensing icon.3. Specify the requested information.

1 Altera recommends that you save any previous license.dat file in a temporary directory, in case you need to refer to it later.

4. When you receive the license file text, you should either save it to a file with the file name license.dat, or copy the lines from the license file to an existing license file. If you are using the license.dat file with the Quartus® II software, Altera recommends that you save your license.dat file in a top-level directory named flexlm.

f For more information, refer to the following literature on the Altera web site:

– Quartus II Installation & Licensing for PCs manual– Quartus II Installation & Licensing for UNIX and Linux Workstations

manual– Application Note 340 (Altera Software Licensing)– Quartus II Software Release Notes– Introduction to Quartus II manual


Revision History

The information contained in the Altera CD Installation Guide version 4.0 revision 1 supersedes information published in previous versions.

Altera CD Installation GuideP25-06810-06BlackPMS 877 SilverAltera Blue (replaces PMS 301 Blue)PMS 541 Blue

Altera Corporation101 Innovation DriveSan Jose, California 95134 USAwww.altera.comwww.altera.com/mysupport P25-06810-06

Altera® CD Installation Guide

Documents

Altera CD Installation Guide · Installing the GNU Tools and Excalibur Component Software ... development and Altera partner kits. ... Altera CD Installation Guide 9