AltechCorp - DIN Rail and Panel Mount Terminal Blocks

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com4

As a leading supplier of terminalblocks for over 17 years, Altech con-tinues to expand the line with themost competitively priced blocks inthe business. Whatever your needsfrom simple wire terminations tosophisticated electronic functions wehave standard and miniature DIN Railmounted terminal blocks to meetthem. Available as individual terminalblocks or in custom-made assem-blies, look to Altech for the followingfunctions, and more.

• Feed-through•Disconnect•High current•Multi-level•Ground• Fuse• Integrated electronics, standardand custom

When you are competing in the globalmarketplace, you need world-classcapabilities. Altech DIN Rail compo-nents put those capabilities at your fin-gertips. Altech’s level of quality meetsor exceeds every national and interna-tional standard for performance andsafety.

DINRAILTERMINAL BLOCKS

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 5

SCREW CLAMP TERMINAL BLOCKAltech terminal blocks feature screw clamps for maximum wiring efficiency and reliability. The blocks are suppliedwith open clamps, ready to accept wires. No special wire preparation or wire lugs are required. Simply strip thewire, insert and tighten the screw to the torque for gas-tight, vibration resistant, solid connections.

The screw clamp design uses a tin-plated, solid copper orsolid brass current bar with grooved serration, a steel cageclamp and screws. As the clamp is tightened, the wire ispressed firmly against the current bar, ensuring positive con-nections every time. The steel parts are zinc plated andchromate passivated for maximum resistance against oxida-tion.

When applying tightening torques, use our straight bladescrewdriver to fit the screw hole guides located in the ter-minal block housings.

THE DIN CONCEPTThe heart of the Altech philosophy is the standardized DIN Rail and snap-on terminal block. The DIN Rail makes possi-ble a compact, organized arrangement of terminal blocks and other DIN Rail mount components. This gives more thanjust the appearance of quality; it saves time and space, enhances design capabilities and provides a centralized con-nect-disconnect area where external and/or internal wiring can be connected quickly and efficiently. At the same time,the DIN concept allows designers to take advantage of constant advances in terminal block technology. Altech DINRail components do more than terminate wires. They distribute power and ground, protect against overloads and per-form a host of other sophisticated functions. Whatever the application: control systems, instrumentation, automa-tion—DIN Rail terminal blocks can help you create it and keep it as up-to-date as tomorrow.

ATEX APPROVEDTERMINAL BLOCKSMany of Altech terminal blocks are AEx eII Ex eII ATEX* approved. They can be used in potentially explosive applications whichmay occur in chemical and petrochemical industry. These terminals can be used in Class 1, Zones 0, 1 and 2 hazardous locations.These terminal blocks comply to EN 500019.The ATEX Directive besides taking into account the electrical sources of explosion, also considering potentially explosive concentrations of gas,vapor or mist along with dust in the air. The ATEX Directive identities two groups of equipment as per EN 50014.

Group 1 where the equipment is intended for use in mining applications.Group 2 where the equipment is intended for all situations other than mines.These groups are further classified into Zones. Zones are areas where there is risk of flammable material being released in the atmosphere.These zones describe the probability of a flammable material being released to atmosphere in explosive concentrations.Zone 0 is the highest risk zone where an explosive atmosphere is expected to exist continuously or for very long periods of time.Zone 1 is an area where an explosive atmosphere is expected to exist for short periods of time, but during a year the accumulation of suchevents is not in excess of 10000 hours.Zone 2 is an area where an explosive concentration of flammable material is not expected and should it be released it will only exist for a veryshort period of time and where the accumulation of events over a year does not exceed much in excess of 10 hours.*CERT #TUV 06 ATEX 2968U

CUSTOM ASSEMBLIESThe beauty of the DIN Rail concept is its convenience; the unsurpassed ease with which many different components and devicescan be mounted on the same rail.

Altech has made things even easier by making it possible for you to order custom designed assemblies with a single part numberor, for that matter, your own drawing number. No need to order amultitude of parts, no more unwanted inventories of bulk-pack-aged accessories.

Send Altech your drawings or specifications, and our experi-enced staff will build, mark and ship your assembly, ready forinstallation. Our on-staff engineers will also assist you in review-ing your drawings.

SPECIFICATIONS

Material Polyamide 6.6Specific Gravity 1.14 - 1.15Upper LimitTemperature 105°C*Lower LimitTemperature - 50°CVolume Resistivity 1012Ω cmSurface Resistivity 1010ΩDielectric Strength 400KV/cmFlammability (UL 94) V2 Grade*

HOUSINGSThe metal parts of Altech terminal blocks are housed in precision-molded, self-extinguishing polyamide 6.6 material for maximumdielectric strength, electrical insulation and temperature resistance. Standard features on all housings include funnel-shaped wireentry openings and screwdriver guides.

SPRING CLAMP CONNECTIONThe spring clamp series terminal blocks offer a time saving alter-native to the popular screw clamp connection.

The pre-stressed spring is opened using a tool (screw driver) so theconductor can be inserted into the insertion space through an open-ing in the spring leg. The conductor is pulled against the current barunder spring force when the tool is removed.

A high contact force is acheived by the design of the spring clampsystem. The design delivers a secure and reliable connection forany application.

Use screwdriverto open spring

Wire islocked in

Wire isinserted

AEx eII Ex eII

* All blocks are availablewith 130°C material,VO grade, on request.



Red

Grey

Color BlocksGray is the standard color, however a choice of red, yellow, blue, black, white, biege, orange and greenare available. Color blocks are ideal for defining circuits and simplifying wiring.

Yellow Blue Black White Biege Orange Green Dk. Brown

COLOR BLOCKSGray is the standard color, however a choice of red, yellow,blue, black, white, biege, orange and green are available. Colorblocks are ideal for defining circuits and simplifying wiring.

Last, but not least, the indispensable extras. End Stops prevent terminal blocks and other components from sliding laterally on therail. End Plates close off the last terminal in a row of terminals. Isolation Partitions provide visual separation of terminal groups andensure electrical isolation between adjacent terminals of different potentials. A wide selection of insulated and uninsulated fer-rules is offered for your applications and whenever stranded flexible wires must be terminated.

Finally, Altech’s carefully chosen, top-quality tools make wire preparation and connection fast, easy and efficient. Our selectionincludes insulated and uninsulated screwdrivers, wire strippers and hand, power and semi-automatic crimpers.

ACCESSORIESAltech offers a comprehensive array of DIN Rail accessories, carefully crafted to enhance your design capabilities and to put thecrucial finishing touch on your designs.

Internal and External Jumpers are available in standard 2, 3, 4 and 10 pole assemblies for interconnection to distribute potentialswithin terminal block assemblies.

Marking Tags make DIN Rail assemblies easier to wire and facilitate troubleshooting. Altech’s extensive terminal block marking sys-tem includes standard or custom imprinted snap-on tags in a variety of sizes for circuit identification. The Altech marking systemoffers two different versions of marking systems for printing of accessories.

DIN Rails are internationally standardized and available in 35mm, 32mm, and 15mm sizes, with or without perforations.

To help with your selection, the appropriate rail size for each terminal block is listed in the ordering information on each page.Additional selection and ordering information for DIN Rails can be found in the Accessories Section.

CTS2.5U-N CTS4U-NAltech “U” Series Universal RailMounting Standard ScrewClamp Feed through terminalsare the most versatile terminalsfor wire-to-wire connection incontrol, automation, instrumen-tation and power distributionapplications. A special designfeature on the flexible footenables easy mounting and dis-mounting from the DIN Rail withthe help of a screwdriver.

The terminals with AEx eIIEx eII can be used in apotentially explosive atmos-phere which may occur inchemical and petrochemicalindustry.These terminals canbe used in Class 1, Zone 0, 1& 2 hazardous locations.These terminal blocks com-ply to En 500019.

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition

Separator Plate

DIN Railfor ordering informationrefer to page 70

End Stopfor ordering informationrefer to page 72

InternalJumper

InsulatedInternalJumper

CurrentBars

Shorting Sleeve & Screw

ExternalJumper

MarkingTags

2 pole3 pole4 pole10 pole100 pole


2 pole3 pole4 pole10 pole

10 pole (breakable)100 pole


5mm

45 x 43mm

9mm

Polyamide 6.6

2 screw clamps & 1 tapped hole for cross connect.

22-12 AWG 0.5-2.5 sq.mm 22-14 AWG

600V 800V 600V

25A 24A 20A

7 lb-in 0.4 Nm 7 lb-in

Cat. No. Std. Pk.

CTS2.5U-N 50

EP2.5/4UN 50

PP2.5/4UN 50

SP2.5/4UN 100

CA702 50CA802 50

CA721/2 100CA721/3 50CA721/4 50CA721/10 10CA721/100 10

CA741/2 100CA741/3 50CA741/4 50CA741/10 10CA741/100 10

CA703/01 100CA704/01 100CA705/01 100CA731/10 100—CA731/100 10

CA 707/S/Q/01 100

CA717/2 100CA717/3 100CA717/4 100CA717/10 25

MT5 100MT6F 10

COLOR BLOCKS(other than grey standard)

When ordering please addcolor suffix to Cat. No.

Example: CTS2.5U-N/R

Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB

6 mm

45 x 43 mm

9 mm

Polyamide 6.6

2screwclamps&1tappedholeforcrossconnect.

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 800 V 600 V

35/40 A* 32 A 35/40A*


Cat. No. Std. Pk.

CTS4U-N 50

EP2.5/4UN 50

PP2.5/4UN 50

SP2.5/4UN 100

CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 10

CA742/2 100CA742/3 50CA742/4 50CA742/10 10CA742/100 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA713/2 100CA713/3 100CA713/4 50CA713/10 25

MT6 100MT6F 10

* 35A with one No. 10 AWG and40A with two No. 12 AWG wires.

E220514


E220514

AEx eIIEx eII

AEx eIIEx eII

Feed-Through


E220514

CTS16U

12 mm

47 x 43 mm

16 mm

Polyamide 6.6


22-6 AWG 2.5-16 sq.mm 20-4 AWG

600 V 800 V 600 V

70 A 76 A 85 A


Cat. No. Std. Pk.

CTS16U 50

SP6/10U 100

CA702 50CA802 50

CA751/2 50CA751/3 50CA751/4 50CA751/10 10

CA761/2 50CA761/3 50CA761/4 50CA761/10 10

CA703/8 100CA704/8 100CA705/8 100CA739/10 100

CA707/S/Q/5 100

MT12 100MT6F 10

CTS6U CTS10U CTS25U

8 mm

47 x 43 mm

12 mm

Polyamide 6.6


22-8 AWG 1.5-6 sq.mm 22-8 AWG

600 V 750 V 600 V

50 A 41 A 50 A


Cat. No. Std. Pk.

CTS6U 50

EP6/10U 50

PP6/10U 50

SP6/10U 100

CA702 50CA802 50

CA723/2 100CA723/3 50CA723/4 50CA723/10 10

CA743/2 100CA743/3 50CA743/4 50CA743/10 10

CA703/2 100CA704/2 100CA705/2 100CA733/10 100

CA707/S/Q/1 100

CA710/2 100CA710/3 100CA710/4 100CA710/10 25

MT8 100MT6F 10

10 mm

47 x 43 mm

12 mm

Polyamide 6.6


22-6 AWG 1.5-10 sq.mm 16-6 AWG

600 V 750 V 600 V

65 A 57 A 65 A


Cat. No. Std. Pk.

CTS10U 50

EP6/10U 50

PP6/10U 50

SP6/10U 100

CA702 50CA802 50

CA724/2 100CA724/3 50CA724/4 50CA724/10 10

CA744/2 100CA744/3 50CA744/4 50CA744/10 10

CA703/3 100CA704/3 100CA705/3 100CA734/10 100

CA707/S/Q/1 100

CA718/2 100CA718/3 50CA718/4 50CA718/10 25

MT10 100MT6F 10

12 mm

56 x 49 mm

18 mm

Polyamide 6.6


12-2 AWG 6-25 sq.mm 14-2 AWG

600 V 800 V 600 V

115 A 101 A 115 A


Cat. No. Std. Pk.

CTS25U 50

EP25U

PP25UN 50

CA702 50CA802 50

CA725/2 50CA725/3 25CA725/4 25CA725/10 10

CA745/2 50CA745/3 25CA745/4 25CA745/10 10

CA703/4 100CA704/4 100CA705/4 100CA735/10 100

CA707/S/Q/2 100

MT12 100MT6F 10

AEx eIIEx eII

AEx eIIEx eII

AEx eIIEx eII

Feed-Through

E220514 E220514 E220514

CTS95U

25 mm

90 x 83 mm

24 mm

Polyamide 6.6

2 screw clamp connections

2-4/0 AWG 25-95 sq.mm 2-4/0 AWG

600V 1000 V 600 V

230 A 232 A 230 A

160 lb-in 18.2 Nm 160 lb-in

Cat. No. Std. Pk.

CTS95U 10

CA202 50CA102 50

MT25 100MT6F 10


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

Isolation Partition


End Stopfor ordering info.refer to page 72

InternalJumper


CurrentBars

Shorting Sleeve& Screw

ExternalJumper

MarkingTags






CTS50U

20.5 mm

75.5 x 71 mm

22 mm

Polyamide 6.6

2 screw clamp connections

6-2/0 AWG 16-50 sq.mm 6-2/0 AWG

600V 1000 V 600 V

150 A 150 A 150 A


Cat. No. Std. Pk.

CTS50U 10

CA202 50CA102 50

MT20 100MT6F 10

CTS35UN

Feed-Through

16 mm

58 x 52.5 mm

18 mm

Polyamide 6.6

2 screw clamps & 1 tapped hole for cross

2-12 AWG 4-35 sq.mm 2-12 AWG

600 V 750 V 600 V

130 A 125 A 130 A


Cat. No. Std. Pk.

CTS35UN 50

PP35UN 50

CA702 50CA802 50

CA771/2 50CA771/3 25CA771/4 25CA771/10 10

CA781/2 50CA781/3 25CA781/4 25CA781/10 10

CA703/10 100CA704/10 100CA705/10 100CA770/10 100

CA707/S/Q/2 100

MT16 100MT6F 10

CTS35U

15 mm

58 x 52.5 mm

18 mm

Polyamide 6.6

2 screw clamps & 1 tapped hole for cross

8-2 AWG 10-35 sq.mm 8-2 AWG

600 V 750 V 600 V

145 A 125 A 145 A


Cat. No. Std. Pk.

CTS35U 50

PP35U 50

CA702 50CA802 50

CA726/2 50CA726/3 25CA726/4 25CA726/10 10

CA746/2 50CA746/3 25CA746/4 25CA746/10 10

CA703/5 100CA704/5 100CA705/5 100CA736/10 100

CA707/S/Q/2 100

MT15 100MT6F 10

AEx eIIEx eII

E220514 E220514 E220514 E220514


CMC1-2 CMC2-2Connect multiple wires to a singleterminal block and eliminate relia-bility problems encountered whenconnecting two wires into a singleclamp.Two versions are available.

Type CMC1-2 features a singlescrew-cage clamp for 22-10 AWGwires on one side and two clampson the other side for 22-10 AWGwires.

Type CMC2-2 has two identicalclamps for 22-10 AWG wires onboth sides.

6 mm

51.5 x 65 mm

9 mm

Polyamide 6.6

4screwclamps&2tappedholesforcrossconnection

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 650 V 600 V

35 A 32 A 35 A

7 lb-in. 0.5 Nm 7 lb-in.

Cat. No. Std. Pk.

CMC2-2 50

EPCMC2-2 50

CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5

CA742/2 100CA742/3 50CA742/4 50CA742/10 10CA742/100 5

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA713/2 100CA713/3 100CA713/4 50CA713/10 25

MT6 100





TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Separator Plate



InternalJumper


CurrentBars


ExternalJumper

MarkingTags






6 mm

47 x 46.5 mm

9 mm

Polyamide 6.6

3screwclamps&1tappedholeforcrossconnection

22-10AWG 0.5-4 sq.mm 22-10 AWG

600 V 650 V 600 V

35 A 32 A 35 A

7 lb-in. 0.5 Nm 7 lb-in.

Cat. No. Std. Pk.

CMC1-2 100

EPCMC1-2 50

CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5

CA742/2 100CA742/3 50CA742/4 50CA742/10 10CA742/100 5

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA713/2 100CA713/3 100CA713/4 50CA713/10 25

MT6 100

Feed-Through Multi-Connection

E220514 E220514

CDL4U CDL4U(I.S)Altech double level terminalsare the answer to high wiringdensity problems posed by cer-tain unavoidable wiring arrange-ments. Double level terminalshave the following advantages:

• Double wiring density avail-able without extension ofmounting rails.

• Interconnection/shorting canbe done at both levels.

• Marking/identification bymarking tags possible atboth levels.

CDL4U(I.S) internally shorteddouble level terminals are usefulfor distribution applications byusing shorting links at lower lev-els.

6 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps & 2 tapped holes for cross connection

22-10 AWG 0.5-4 sq.mm 22-10 AWG

300V 400 V 600 V

35 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U 100

EPCDL4U 50

SPCDL4U 100

CA702 50CA802 50

CA727/2 100CA727/3 50CA727/4 50CA727/10 10

CA747/2 100CA747/3 50CA747/4 50CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 50CA714/10 25

MT2 100

6 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps & 1 tapped hole for cross connection

22-10 AWG 0.5-4 sq.mm 22-10 AWG

300 V 400 V 600 V

35 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(I.S) 100

EPCDL4U 50

SPCDL4U 100

CA702 50CA802 50

CA727/2 100CA727/3 50CA727/4 50CA727/10 10

CA747/2 100CA747/3 50CA747/4 50CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 50CA714/10 25

MT2 100





E220514 E220514


Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Separator Plate



InternalJumper


CurrentBars


ExternalJumper

Marking Tags






Feed-Through Double Level


ODL4UAltech Offset Double LevelTerminals, which provide a sep-arate connection at two levels.In ODL, the top level is offsetfrom the bottom level by halfthe thickness of the terminal.

This offset provides betteraccessibility to the screws onthe lower level.

*It is recommended to use endplates at both ends of assem-bled ODL terminal sets for flatalignment to enable effectiveuse of end stops.

6 mm

63 x 68 mm

9 mm

Polyamide 6.6

4screwclamps&2tappedholesforcrossconnection

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 630 V 600 V

35 A 32 A 35 A


Cat. No. Std. Pk.

ODL4U 50

EPODL4U 50EP1ODL4U 50

CA702 50CA802 50

CA727/2 10CA727/3 10CA727/4 10CA727/10 10

CA747/2 100CA747/3 50CA747/4 50CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 50CA714/10 25

MT6 100





TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper


CurrentBars


ExternalJumper

MarkingTags






FrontBack

Feed-Through Offset Double Level

E220514

CTL2.5U-H CTL2.5U

6 mm

67 x 61 mm

9 mm

Polyamide 6.6

4Screwclamps&3 tappedholes for cross connect.

22-12 AWG 0.5-2.5 sq.mm 22-12 AWG

300 V 500 V 300 V

25 A 24 A 25 A

4.5 lb-in 0.4 Nm 4.5 lb-in

Cat. No. Std. Pk.

CTL2.5U-H 50

EPCTL2.5U-H 50

CA202 50CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA715/2 100CA715/3 100CA715/4 100CA715/10 50

MT2 100

6 mm

67 x 84 mm

9 mm

Polyamide 6.6


22-12 AWG 0.5-2.5 sq.mm 22-12 AWG

300 V 500 V 300 V

25 A 24 A 25 A

4.5 lb-in 0.4 Nm 4.5 lb-in

Cat. No. Std. Pk.

CTL2.5U 50

EPCTL2.5U 50

CA202 50CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA715/2 100CA715/3 100CA715/4 100CA715/10 50

MT2 100

For applications with extremespace constraints. Only 6mm(.236”) wide, with three sepa-rate feed-through levels.Jumpers can be used toreduce field wiring.

They can also be used in con-trol systems where sensorsand actuator applications areinvolved.

The top level of CTL2.5UH ter-minal block provide connectingpoints for signal while middleand bottom level provide con-necting points are used forpositive and negative poten-tial.

In applications where switch-ing indication is required,choice of CTL2.5UHL andCTL2.5UL terminal blocks withbuilt-in electronic componentsare available.





E220514 E220514


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper

CurrentBars


ExternalJumper

MarkingTags





Feed-Through Triple Level

CDLG2.5 CTLG2.5

6 mm

50 x 71 mm

9 mm

Polyamide 6.6

5 Screw clamps & 2 tapped holes for cross connect.

24-12 AWG

300 V

24 A

7 lb-in

Cat. No. Std. Pk. CDLG2.5 50

EPCDLG2.5 50

CA202 50CA702 50CA802 50

CA627/2 100CA627/3 50CA627/4 50CA627/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA611/S/Q 100

CA715/2 100CA715/3 100CA715/4 100CA715/10 50

MT2 100

6 mm

62 x 87.5 mm

9 mm

Polyamide 6.6

7 Screw clamps & 1 tapped holes for cross connect.

24-12 AWG

300 V

24 A

7 lb-in

Cat. No. Std. Pk. CTLG2.5 50

EPCTLG2.5 50

CA202 50CA702 50CA802 50

CA627/2 100 CA627/3 50 CA627/4 50 CA627/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA611/S/Q 100

CA715/2 100CA715/3 100CA715/4 100CA715/10 50

MT2 100

The CDLG2.5 is a double leveland the CTLG2.5 is a triplelevel terminal block with anadditional connection point forearthing (Grounding) cables.

This separate connection pointis appropriately identified bythe green-yellow imprint on itstop.

The triple level terminal blockis an ideal choice for motor,sensor, actuator and initiatorconnections.





E220514 E220514

Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com

Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper

CurrentBars


ExternalJumper

Marking Tags





Double & Triple

with Ground

Terminal Blocks


* Add required voltage to part number as suffix;i.e. CTL2.5U(L)/24 for 24V DC

CTL2.5U-H(L)* CTL2.5U(L)*

6 mm

67 x 61 mm

9 mm

Polyamide 6.6


12V, 24V, 48V, 110V DC

22-12 AWG 0.5-2.5 sq.mm 22-12 AWG

300 V 500 V 300 V

25 A 24 A 25 A

4.5 lb-in 0.4 Nm 4.5 lb-in

Cat. No. Std. Pk.

CTL2.5U-H(L)* 50

EPCTL2.5U-H 50

CA202 50CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA715/2 100CA715/3 100CA715/4 100CA715/10 50

MT2 100

6 mm

67 x 84 mm

9 mm

Polyamide 6.6


12V, 24V, 48V, 110V DC

22-12 AWG 0.5-2.5 sq.mm 22-12 AWG

300 V 500 V 300 V

25 A 24 A 25 A

4.5 lb-in 0.4 Nm 4.5 lb-in

Cat. No. Std. Pk.

CTL2.5U(L)* 50

EPCTL2.5U 50

CA202 50CA702 50CA802 50

CA722/2 100CA722/3 50CA722/4 50CA722/10 10CA722/100 5

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA707/S/Q/01 100

CA715/2 100CA715/3 100CA715/4 100CA715/10 50

MT2 100

Ideal for sensor applications.See Altech’s Inductive Proximity Sensor catalog

for ordering information.

E220514 E220514

Feed-Through Triple Level

CGT4N

6 mm

45.4 x 54.2 mm

9 mm

Polyamide 6.6

2 screw clamps

22-10 AWG 0.5-4 sq.mm 22-10 AWG


Cat. No. Std. Pk.

CGT4N 50

MT6 100

CGT4UUse ground blocks instead of groundingstuds and wire lugs to terminate groundwires, saving installation and wiring time.

Ground blocks clamp mechanically onto theDIN Rail by tightening the center mountingscrew, making a reliable electrical connec-tion between the cage clamp terminals andthe DIN Rail.The rail serves as a busbar andautomatically distributes ground potentialto all other ground terminals on the samerail.

Ground blocks can also be usedas end stops, preventing other terminalblocks and components from moving later-ally on the DIN Rail.

They are supplied with a standardgreen/yellow housing for easy identificationand accept standard marking tags.

CGT4U, CGT10U and CGT35U can bemounted on both DIN 32mm and DIN35mm rails.

CGT4N, CGT6N and CGT16N can be mount-ed on 35mm DIN rail and have the same topouter profile as the feed through blocks(CTS4U-N, CTS2.5U-N, CTS6U, CTS10U andCTS16U).

• High density• Screw-cage clamp• Special clamping foot• Polyamide 6.6• Color: green/yellow

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Torque

Other Approvals

Terminal Block


End Plate

MarkingTags(MTType)

6 mm

48 x 43 mm

9 mm

Polyamide 6.6

2 screw clamps

22-10 AWG 0.5-4 sq.mm 22-10 AWG


Cat. No. Std. Pk.

CGT4U 50

EPCGT4U 100

MT6 100

E220514 E220514


Assembly for single phase3 wire circuits.

AEx eIIEx eII

Ground Blocks


AEx eII Ex eII

CGT6N

8 mm

47 x 54.5 mm

12 mm

Polyamide 6.6

2 screw clamps

22-8 AWG 1.5-6 sq.mm 22-8 AWG


Cat. No. Std. Pk. CGT6N 50

MT8 100

E220514

CGT10U

10 mm

50 x 45 mm

12 mm

Polyamide 6.6

2 screw clamps

22-6 AWG 1.5-10 sq.mm 16-8 AWG


Cat. No. Std. Pk. CGT10U 50

MT10 100

E220514

AEx eII Ex eII

CGT10N

10 mm

50 x 45 mm

12 mm

Polyamide 6.6

2 screw clamps

22-6 AWG 1.5-10 sq.mm 16-8 AWG



MT10 100

CGT16N

12 mm

47 x 43 mm

16 mm

Polyamide 6.6

2 screw clamps

20-4 AWG 2.5-16 sq.mm 20-4 AWG



MT10 100

E220514

CGT35U

16 mm

61.5 x 58 mm

18 mm

Polyamide 6.6

2 screw clamps

8-2 AWG 10-35 sq.mm 8.2 AWG



MT15 100

E220514

Ground Blocks

➀ UL recognition in progress.

➀UL

CSFL4U CSFL4U(L)*Altech fuse terminals are alsoavailable with light indication -CSFL4U(L). A specially designedbuilt-in circuit gives light indica-tion in the event of fuse blow out.Thus, fault in a circuit can be eas-ily located.

However, an application of suchterminals must take into consid-eration residual current flow.

DDFL4U - Double Level FuseTerminal with fuse link on the toplevel has a separate feed throughterminal at the lower level. Thiseliminates use of an additionalfeed through terminal.

In DDFL4U(E), specially designedbuilt in circuit gives light indica-tion in the event of a fuse blowout at the top level. The terminalprovides separate feed throughconnection possibility at thelower level.

DDFL4U(LR): This is a modifiedversion of DDFL4U(E) terminalwhere in two equipotential con-nection points are available onboth ends of the terminal.

Important:The disconnecting device is notsuitable for interrupting load. Thesupply must be switched off beforeoperating the slide link/lever.

† Fuses are sold separatelyAltech, see pages 23-24.

Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Type of Fuse Used

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition



InternalJumper


CurrentBar


ExternalJumper

Marking Tags (MT Type)(MT Type on Lever)


8 mm

43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25 mm

22-10 AWG 22-10 AWG

600 V 600 V

6.3 A 10 A

7 lb-in 7 lb-in

Cat. No. Std.

CSFL4U(L)* 50

EPCSFL4U 50

PPCSFL4U 50

CA702 50 CA802 50

CA711/2 100CA711/3 100CA711/4 50CA711/10 20

MT8 100 MT2 100

8 mm

43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25 mm

22-10 AWG 22-10 AWG

600 V 600 V

6.3 A 10 A

7 lb-in 7 lb-in

Cat. No. Std. Pk.

CSFL4U 100

EPCSFL4U 50

PPCSFL4U 50

CA702 50CA802 50

CA711/2 100CA711/3 100CA711/4 50CA711/10 20

MT8 100MT2 100

* Add required voltage to part numberas a suffix. i.e. CSFL4U(L)/24 for 24V AC/DC.





E220514 E220514

† Fuse not included. † Fuse not included.


24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC, 300V AC

Fuse Blocks, 5 x 20 and 5 x 25 mm





CSFL6U

8 mm

60 x 43 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25 mm

22-8 AWG 1.5-6 sq.mm 22-8 AWG

300 V 500 V 300 V

10 A 6.3 A 10 A


Cat. No. Std. Pk.

CSFL6U 50

EPCSFL6U 50

CA702 50CA802 50

CA710/2 100CA710/3 100CA710/4 100CA710/10 25

MT8 100MT6 100

E220514

† Fuse not included.

8 mm

66 x 88 mm

9.5 mm

Polyamide 6.6

4 screw clamps

Ø5x20, Ø5x25 mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 6.3 A35 A 32 A 35 A


Cat. No. Std. Pk.

DDFL4U(E)* 20

EPDDFL4U 20

CA702 50CA802 50

CA729/2 100CA729/3 50CA729/4 50CA729/10 10

CA749/2 100CA749/3 50CA749/4 50CA749/10 10

CA703/6 100CA704/6 100CA705/6 100CA737/10 100

CA707/S/Q/3 100

CA711/2 100CA711/3 100CA711/4 50CA711/10 25

MT8 100MT2 100

24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC

8 mm

66 x 88 mm

9.5 mm

Polyamide 6.6

4 screw clamps

Ø5x20, Ø5x25 mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 6.3 A35 A 32 A 35 A


Cat. No. Std. Pk.

DDFL4U 20

EPDDFL4U 20

CA702 50CA802 50

CA729/2 100CA729/3 50CA729/4 50CA729/10 10

CA749/2 100CA749/3 50CA749/4 50CA749/10 10

CA703/6 100CA704/6 100CA705/6 100CA737/10 100

CA707/S/Q/3 100

CA711/2 100CA711/3 100CA711/4 50CA711/10 25

MT8 100MT2 100

DDFL4U DDFL4U(E)*

E220514 E220514


8 mm

66 x 88 mm

9.5 mm

Polyamide 6.6

4 screw clamps

Ø5x20, Ø5x25 mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 6.3 A


Cat. No. Std. Pk.

DDFL4ULR 20

EPDDFL4U 20

CA702 50CA802 50CA202 50

CA730/2 100CA730/3 50CA730/4 50CA730/10 10

CA740/2 100CA740/3 50CA740/4 50CA740/10 10

CA703/7 100CA704/7 100CA705/7 100CA738/10 100

CA707/S/Q/8 100

CA711/2 100CA711/3 100CA711/4 50CA711/10 25

MT8 100MT2 100

DDFL4ULR

E220514



TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Type of Fuse Used

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper


CurrentBar


ExternalJumper

MarkingTags (MTType)(MTType on Lever)





Top LevelBottom Level

DDFL4U(LR): This is a modifiedversion of DDFL4U(E) terminalwhere in two equipotential con-nection points are available onboth ends of the terminal.

CAFL4U(L) is equipped with aLED for blown fuse indication.CAFL4U(N) is equipped with aneon bulb for same application.

Important:The disconnecting device is notsuitable for interrupting load. Thesupply must be switched offbefore operating the slidelink/lever.


* Add required voltage to partnumber as suffix, i.e.DDFL4U(E)/24 for 24V AC/DC






8 mm

66 x 88 mm

9.5 mm

Polyamide 6.6

4 screw clamps

Ø5x20, Ø5x25 mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 6.3 A


Cat. No. Std. Pk.

DDFL4U(E)LR* 20

EPDDFL4U 20

CA702 50CA802 50CA202 50

CA730/2 100CA730/3 50CA730/4 50CA730/10 10

CA740/2 100CA740/3 50CA740/4 50CA740/10 10

CA703/7 100CA704/7 100CA705/7 100CA738/10 100

CA707/S/Q/8 100

CA711/2 100CA711/3 100CA711/4 50CA711/10 25

MT8 100MT2 100

24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC

DDFL4U(E)LR*

E220514




TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Type of Fuse Used

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper


CurrentBar


ExternalJumper






Top LevelBottom Level

CAFL4U

9 mm

50 x 72 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø1/4x1 in., Ø1/4x11/4 in.

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

16 A 6.3 A 16 A


Cat. No. Std. Pk.

CAFL4U 25

EPCAFL4U 50

CA702 50CA802 50

CA716/2 50CA716/3 50CA716/4 50CA716/10 25

MT9 100

CAFL4U(L)* CAFL4U(N)

9 mm

50 x 72 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø1/4x1 in., Ø1/4x11/4 in.

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

16 A 6.3 A 16 A


Cat. No. Std. Pk.

CAFL4U(L)* 25

EPCAFL4U 50

CA702 50CA802 50

CA716/2 100CA716/3 50CA716/4 50CA716/10 20

MT9 100

9 mm

50 x 72 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø1/4x1 in., Ø1/4x11/4 in.

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

16 A 6.3 A 16 A


Cat. No. Std. Pk.

CAFL4U(N) 25

EPCAFL4U 50

CA702 50CA802 50

CA716/2 100CA716/3 50CA716/4 50CA716/10 20

MT9 100

24VAC/DC,48VAC/DC,110VAC/DC, 220VAC,300VAC

110-220VAC/DC,300VAC

E220514 E220514 E220514

† Fuse not included. † Fuse not included. † Fuse not included.

Fuse Blocks, 1/4 x 1 and 1/4 x 11/4 in.

1 POLE 2 POLE 3 POLEThe main characteristics offuse disconnectors are:

• Compliance with IEC60947-1, IEC 60947-3

• UL508 recognized• Plastic parts are made ofmaterial resistant to hightemperatures

• All contact surfaces aresilver plated

• Mounting on standard DIN35 mm rail (DIN EN60715).

• Available up to 4 pole• For all sizes a version withelectronic indicator isavailable. There are twotechnical types of indicator:

L (LED) with built in LEDdiode which blinks after thefuse-link operates. The inter-nal circuit resistance is 2M,thus the total dissipation isminimal. The indicator iscapable of operating in con-ditions of open circuit withminimum capacitance be-tween connection cables.Operating voltage rangespans from 50V to 690V ACand DC.

I (NEON) with neon lamp,which is constantly lit afterthe fuse-link operates. Theinternal circuit resistance is570k, thus it is necessary thatthe circuit be closed in orderfor the indicator to function.The operational voltagerange is 100 V to 750 V AC.

* Fuses are sold separatelyAltech, see pages 23-24.

79 mm (3.11 in.)64.5 mm (2.54 in.)

47.5 mm (1.87 in.)4 mm (0.16 in.)

B

81m

m(3

.19

in.)

37 mm (1.46 in.) Dimension for B:1 Pole 17.5mm1 Pole + Neutral 35mm2 Pole 35mm3 Pole 52.5mm3 Pole + Neutral 70mm

17.5 mm

77 x 63.5 mm

11 mm

Aculon ®

2 screw clamps

Ø10 x 38 mm

24-4 AWG 1.5-25sq.mm 24-4 AWG

690 V 400 V** 690 V

32A 32A** 32A

31 lb-in 2-2.5 Nm 31 lb-in

Cat. No. Std. Pk.

CB1038-1 1CB1038-1/L 1CB1038-1/I 1

CA702 50CA802 50

TerminalWidth (B)

Height x Length

Stripping Length

Insulation Material

Type of Connection

Fusion Voltage

Type of Fuse Used

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Terminal BlockIndicator:NoneLEDNeon

DIN Railfor ordering informa-tionrefer to page 70


E212627

35 mm

77 x 63.5 mm

11 mm

Aculon ®

2 screw clamps

Ø10 x 38 mm

24-4 AWG 1.5-25sq.mm 24-4 AWG

690 V 400 V** 690 V

32A 32A** 32A

31 lb-in 2-2.5 Nm 31 lb-in

Cat. No. Std. Pk.

CB1038-2 1CB1038-1/L 1CB1038-2/I 1

CA702 50CA802 50

E212627

52.5 mm

77 x 63.5 mm

11 mm

Aculon ®

2 screw clamps

Ø10 x 38 mm

24-4 AWG 1.5-25sq.mm 24-4 AWG

690 V 400 V** 690 V

32A 32A** 32A

31 lb-in 2-2.5 Nm 31 lb-in

Cat. No. Std. Pk.

CB1038-3 1CB1038-3/L 1CB1038-3/I 1

CA702 50CA802 50

E212627


Fuse Blocks, 10 x 38 mm


38 mm(1.5 in.)

Ø10.3 mm(0.4 in.)

6 mm(0.24 in.)

6 mm(0.24 in.)

10.5 mm(0.4 in.)

10.5 mm(0.4 in.)

10x38

Operating PowerIn Cat. No. I2-value Dissipation Std. Pk.(A) (A’s) (W)

1 2645126 1.6 1 102 2645127 8 1.8 104 2645128 8 1.1 106 2645129 25 1.6 108 2645130 39 1.8 10

10 2645131 66 2.1 1012 2645132 87 3.1 1016 2645133 166 4.4 1020 2645134 280 5.8 1025 2645135 580 6.8 1030 2645136 1.010 8.2 10

10x38

10x38

10x38

6 2625005 30 1.5 108 2625006 50 2 10

10 2625007 70 2.5 1012 2625008 120 3 1016 2625009 150 3.5 1020 2625011 260 4.8 1025 2625013 290 6 1032 2625015 600 7.5 10

** 6-25A (700V DC/ breaking capacity ––--- 50kA)32A (400V DC/ breaking capacity ––--- 50kA)

Operating PowerIn Cat. No. I2-value Dissipation Std. Pk.(A) (A’s) (W)

Rated Current/RatedVoltate Cat. No. Std. Pk.

0.5A 2620017 101A 2620000 102A 2620001 104A 2620003 106A 2620005 108A 2620006 1010A 2620007 1012A 2620008 1016A 2620009 1020A 2620011 1025A 2620013 1032A* 2620015 10

*400V

Rated Current/RatedVoltate Cat. No. Std. Pk.

0.5A 2621017 101A 2621000 102A 2621001 104A 2621003 106A 2621005 108A 2621006 1010A 2621007 1012A 2621008 1016A 2621009 1020A 2621011 1025A 2621013 1032A* 2621015 10

*400V

Cylinder Fuses are typically used inindustrial applications to protect electri-cal devices such as motors, drives, etc.

They are available in four sizes with acurrent range from 1 to 125 Amps.Cylinder Fuses have metal caps at bothends, and a porcelain fuse body.

OPERATING CLASSES

gL/gG - Line ProtectionSlow, typically used for distribution cir-cuits or resistive loads.

Typical Markings: gL/gG

aM - Motor ProtectionFast acting short circuit protection,but slow acting overload protection.

Typical Marking: aM

aR - Semiconductor Protection

Partial range, short circuit protectionfor devices such as diodes, SCRs. etc.

Typical Markings: Ultra Rapid™,Sitor™, Silcu™, Protister™, Recticur™,Ultra Quick™, aR

gR - Semiconductor Protection

Full range, short circuit protection fordevices such as diodes, SCRs. etc.

Typical Markings: Ultra Rapid™,Sitor™, Silcu™, Protister™, Recticur™,Ultra Quick™, gR

Note:Other fuse sizes and fuse holdersare available. Please refer to theAltech European Fuse catalog formore information.

gL/gG - Line ProtectionStandard: IEC 20269-4-1and IEC60269-1

Rated Voltage: 500V

aM - Motor ProtectionStandard: IEC 20269-4-1and IEC60269-1

Rated Voltage: 500V

aR - Semiconductor ProtectionStandard: IEC 60269-4-1Breaking Capacity: ~200 kARated Voltage: ~600V**

gR - Semiconductor ProtectionStandard: IEC 60269-4-1Breaking Capacity: ~200 kARated Voltage: ~690V

Certified for 700V

Fuses

Voltage 250V AC/DCDIN 41662 DIN 41571-2 DIN 41661IEC-127-2/III IEC-127-2/II

Cat. No.Slow Medium Fast

0.02M5x20M0.032M5x20M

0.05M5x20T4 0.05M5x20M 0.05M5x20F4

0.063M5x20M0.08M5x20T4 0.08M5x20M0.1M5x20T4 0.1M5x20M 0.1M5x20F4

0.125M5x20T4 0.125M5x20M 0.125M5x20F4

0.16M5x20T4 0.16M5x20M 0.16M5x20F4

0.2M5x20T4 0.2M5x20M 0.2M5x20F4

0.25M5x20T4 0.25M5x20M 0.25M5x20F4

0.315M5x20T4 0.315M5x20M 0.315M5x20F4

0.4M5x20T4 0.4M5x20M 0.4M5x20F4

0.5M5x20T4 0.5M5x20M 0.5M5x20F4

0.63M5x20T4 0.63M5x20M 0.63M5x20F4

0.7M5x20T4 0.7M5x20M 0.7M5x20F4

0.8M5x20T4 0.8M5x20M 0.8M5x20F4

1.0M5x20T4 1.0M5x20M 1.0M5x20F4

1.25M5x20T4 1.25M5x20M 1.25M5x20F4

1.4M5x20T4 1.4M5x20M1.6M5x20T4 1.6M5x20M 1.6M5x20F4

2.0M5x20T4 2.0M5x20M 2.0M5x20F4

2.5M5x20T4 2.5M5x20M 2.5M5x20F4

3.15M5x20T4 3.15M5x20M 3.15M5x20F4

4.0M5x20T4 4.0M5x20M 4.0M5x20F4

5.0M5x20T4 5.0M5x20M 5.0M5x20F4

6.3M5x20T4 6.3M5x20M 6.3M5x20F4

8.0M5x20T1 8.0M5x20M 8.0M5x20F1

10.0M5x20T1 10.0M5x20M 10.0M5x20F1

12.5M5x20T1 12.5M5x20M1 12.5M5x20F1

16.0M5x20T1 16.0M5x20M1 16.0M5x20F1

20.0M5x20T1 20.0M5x20M1 20.0M5x20F1

Std. Pk. 10

Voltage 250V AC/DC

Cat. No.Slow Fast

0.032M6.3x32T0.04M6.3x32T0.05M6.3x32T4 0.05M6.3x32F0.063M6.3x32T4 0.063M6.3x32F0.08M6.3x32T4 0.08M6.3x32F0.1M6.3x32T4 0.1M6.3x32F0.125M6.3x32T4 0.125M6.3x32F0.16M6.3x32T4 0.16M6.3x32F0.2M6.3x32T4 0.2M6.3x32F0.25M6.3x32T4 0.25M6.3x32F0.315M6.3x32T4 0.315M6.3x32F

0.4M6.3x32T4 0.4M6.3x32F0.5M6.3x32T4 0.5M6.3x32F0.63M6.3x32T4 0.63M6.3x32F0.7M6.3x32T4 0.7M6.3x32F0.8M6.3x32T4 0.8M6.3x32F1.0M6.3x32T4 1.0M6.3x32F4

1.25M6.3x32T4 1.25M6.3x32F4

1.6M6.3x32T4 1.6M6.3x32F4

2.0M6.3x32T4 2.0M6.3x32F4

2.5M6.3x32T4 2.5M6.3x32F2,4

3.15M6.3x32T4 3.15M6.3x32F2,4

4.0M6.3x32T4 4.0M6.3x32F2,4

5.0M6.3x32T4 5.0M6.3x32F3,4

6.3M6.3x32T4 6.3M6.3x32F3,4

7.0M6.3x32T4 7.0M6.3x32F3

8.0M6.3x32T4 8.0M6.3x32F3

10.0M6.3x32T4 10.0M6.3x32F3

12.5M6.3x32T4 12.5M6.3x32F3

16.0M6.3x32T4 16.0M6.3x32F3

20.0M6.3x32T4 20.0M6.3x32F3

Std. Pk. 10

Voltage 250V AC/DCDIN 41571-2

Cat. No.Medium

0.032M5x25M0.04M5x25M0.05M5x25M0.063M5x25M0.08M5x25M0.1M5x25M0.125M5x25M0.16M5x25M0.2M5x25M0.25M5x25M0.315M5x25M

0.4M5x25M0.5M5x25M0.63M5x25M0.8M5x25M

1.0M5x25M1.25M5x25M1.6M5x25M

2.0M5x25M2.5M5x25M

3.15M5x25M4.0M5x25M5.0M5x25M6.3M5x25M

8.0M5x25M1

10.0M5x25M1

16.0M5x25M1

Std. Pk. 10

Miniature Fuses are typicallyused to protect electronicdevices, laboratory and meas-urement instruments, stereos,TV’s,VCR’s etc.They are availablein four sizes with a current rangeof 20mA to 20 Amps. MiniatureFuses are manufactured accord-ing to VDE 0820 part 1, VDE 0820part 2, IEC publication 127, CEEpublication 4 and actual DINstandards.

The 5x20, 5x25 fuses can be usedin the CSFL4U series terminalblocks. The 6.3x32 fuse can beused in the CAFL4U series termi-nal blocks.

Operating Class:Slow,Typical Marking: “T”Medium,Typical Marking: “M”Fast,Typical Marking: “F”

1 Not standard rating.2 Rated Voltage 150V.3 Rated Voltage 60V.4 UL recognized version

available upon request.

5 X 20 5 X 25 6.3 X 32 (1/4” X 1-1/4”)

Current

20mA32mA40mA50mA63mA80mA

100mA125mA160mA200mA250mA315mA

400mA500mA630mA700mA800mA

1.0A1.25A1.4A1.6A2.0A2.5A

3.15A4.0A5.0A6.3A7.0A8.0A

10.0A12.5A16.0A20.0A

upon request upon request


Miniature Fuses

Altech’s increasingly popular industrialenclosures keep you well covered with theirhigh quality and attractive design.

All at Very Competitive Prices!And many available for immediate delivery.

Customization available!

Illustrated are just a few of the applications for our enclosures.

Rustproof• Polycarbonate/Polystyrene enclosures will

last indefinitely without corrosionVisibility

• Components and devices are fully visiblethrough transparent covers, whilecompletely protected and insulated

Impact Resistant• Non-metallic enclosures

withstand bumps andblows, they will not dent

Maintenance Free• Surface finish does not

deteriorate and requiresno special painting orrefinishing

Chemical resistant• Resist weak and

strong acids andalkali

Lightweight• Non-metallic

enclosures weighsignificantly less thanmetal, simplifyinghandling

Flexibility• Enclosures can be

easily customized


CDTTU CDTTU-SH

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition



InternalJumper


CurrentBar


ExternalJumper



8 mm

57 x 63 mm

12 mm

Polyamide 6.6

2 screw clamps

16-8 AWG 1.5-6 sq.mm 16-8 AWG

600 V 800 V 600 V

41 A 41 A 41 A


Cat. No. Std. Pk.

CDTTU 50

EPCDTTU 50

CA702 50CA802 50

CA710/2 100CA710/3 100CA710/4 100CA710/10 25

MT8 100

Disconnect and test terminals arean ideal choice for measuringcontrol and regulatory circuits.The terminals provide a clearfunctional advantage for deviceshaving utility instruments andassociated transformers.

Five versions of disconnect andtest terminals are available:

• CDTTU - disconnection isachieved by means of a slidelink operated with a screw driver.

• CDTTU-SH - disconnect and testterminals are ideal for use incurrent transformer applicationswhen it is mandatory to keep thesecondary side shorted at anypoint while taking currentmeasurements.

• CKT4U - disconnection isachieved by lifting theknife contact lever.

• CSDL4U - hinged disconnectionand testing terminal,incorporates a connecting link inplace of the fuse link.

• CSDL6U - hinged disconnectblock for 8 AWG size wires.

• DDDL4U - double leveldisconnect terminal with hingeddisconnect in upper level.

Specially designed socket headscrews act as test/monitoringpoints in both CDTTU, CDTTU-SHand CKT4U.

Important: The disconnectingdevice is not suitable for interrupt-ing load. The supply must beswitched off before operating theslide link/lever.

16 mm

57 x 63 mm

12 mm

Polyamide 6.6

4 screw clamps

16-8 AWG 1.5-6 sq.mm 16-8 AWG

300 V 300 V 300 V

10 A 10 A 10 A


Cat. No. Std. Pk.

CDTTU-SH 50

EPCDTTU 50

CA702 50CA802 50

CA710/2 100CA710/3 100CA710/4 100CA710/10 25

MT8 100

E220514


Disconnect





CKT4U CSDL4U DDDL4U

8 mm

43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

14 A 6.3 A 14 A


Cat. No. Std. Pk.

CSDL4U 100

EPCSFL4U 50

PPCSFL4U 50

CA702 50CA802 50

CA711/2 100CA711/3 100CA711/4 50CA711/10 25

MT8 100MT2 100

8 mm

66 x 88 mm

9.5 mm

Polyamide 6.6

4 screw clamps

22-10 AWG 22-10 AWG

300 V 300 V

14 / 35 A 14 / 35 A

7 lb-in 7 lb-in

Cat. No. Std. Pk.

DDDL4U 20

EPDDFL4U 20

CA702 50CA802 50

CA729/2 100CA729/3 50CA729/4 50CA729/10 10

CA749/2 100CA749/3 50CA749/4 50CA749/10 10

CA703/6 100CA704/6 100CA705/6 100CA737/10 100

CA707/S/Q/3 100

CA711/2 100CA711/3 100CA711/4 50CA711/10 25

MT8 100MT2 100

6 mm

46 x 46.3 mm

9 mm

Polyamide 6.6

2 screw clamps

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 800 V 600 V

16 A 16 A 16 A


Cat. No. Std. Pk.

CKT4U 50

EPCKT4U 50

CA702 50CA802 50

CA713/2 100CA713/3 100CA713/4 50CA713/10 25

MT6 100

CSDL6U

8 mm

60 x 43 mm

9.5 mm

Polyamide 6.6

2 screw clamps

22-8 AWG 1.5-6 sq.mm 22-8 AWG

300 V 500 V 300 V

10 A 6.3 A 10 A


Cat. No. Std. Pk.

CSDL6U 50

EPCSFL6U 50

CA702 50CA802 50

CA710/2 100CA710/3 50CA710/4 50CA710/10 25

MT8 100

E220514 E220514 E220514

Disconnect

CDB4/x CDB4/x(1)Altech CDB Compact Distribu-tion Blocks are an ideal choicefor a simplified distribution sys-tem. A lug/bolt secures theincoming cable and the screwclamp design of the block pro-vides the outgoing connec-tions. These provide easy con-nect points and ensure perfectcontinuity for distribution. Aprotective shield effectivelyshrouds the incoming connec-tion.

Application Information:Sum of outgoing currents oneither side of center should notexceed half the maximum per-missible incoming current.

Sum of total outgoing currentsshould not exceed maximumpermissible incoming current.

Connection for higher outgoingcurrents should be donethrough the terminal nearest tothe incoming connection.

TerminalWidth

Height &Width

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block



MarkingTags (MTType)

Warning Label

6 mm

45 x 43 mm

9 mm

Polyamide 6.6

10-8 AWG 6-16 sq.mm 10-8 AWG22-12 AWG 0.5-4 sq.mm 22-10 AWG

600 V 800 V 600 V

50 A 50 A25 A 32 A 35 A

26 lb-in 2.0 Nm 26 lb-in7 lb-in 0.5 Nm 7 lb-in

Cat.No. HxWxL (mm) Outputs Std.Pk.

CDB4/1 45 x 43 x 43.8 4 10CDB4/2 45 x 43 x 55.8 8 10CDB4/3 45 x 43 x 67.8 12 10CDB4/4 45 x 43 x 80 16 5CDB4/5 45 x 43 x 96 20 5

Cat. No. Std. Pk.

CA702 50CA802 50

MT6 100

InputOutput

InputMax. Individual Output

InputOutput

1 Lug/ M5 bolt connection for ring lugScrew clamp connection

InputOutput

6 mm

45 x 43 mm

9 mm

Polyamide 6.6


600 V 800 V 600 V

50 A 50 A25 A 32 A 35 A


Cat.No. HxWxL (mm) Outputs Std.Pk

CDB4/2(1) 45 x 43 x 52 4 10CDB4/3(1) 45 x 43 x 58 6 10CDB4/4(1) 45 x 43 x 64 8 5CDB4/5(1) 45 x 43 x 70 10 5CDB4/6(1) 45 x 43 x 76 12 5CDB4/10(1)45 x 43 x 100 20 5CDB4/11(1)45 x 43 x 106 22 5

Cat. No. Std. Pk.

CA702 50CA802 50

MT6 100

1 Lug M5 /bolt connection for ring lugScrew clamp connection





E220514 E220514


Distribution Block


CDB25/x

12 mm

56 x 49 mm

18 mm

Polyamide 6.6

6-2/0 AWG 10-50 sq.mm 6-2/0 AWG12-2 AWG 6-25 sq.mm 12-2 AWG

600 V 800 V 600 V

150 A 150 A75 A 101 A 75 A

53 lb-in 6.0 Nm 53 lb-in14 lb-in 2 Nm 14 lb-in

Cat. No. H x W x L (mm) Outputs Std.Pk

CDB25/2 56 x 49 x 88 8 10CDB25/3 56 x 49 x 112 12 10CDB25/4 56 x 49 x 136 16 5

Cat. No. Std. Pk.

CA702 50CA802 50

MT12 100

CDB6/x CDB10/x

8 mm

43 x 47 mm

12 mm

Polyamide 6.6


600 V 800 V 600 V

100 A 100 A50 A 41 A 50 A




Cat. No. Std. Pk.

CA702 50CA802 50

MT8 100

SWL6 100


10 mm

43 x 47 mm

12 mm

Polyamide 6.6

8-1/0 AWG 10-35 sq.mm 8-1/0 AWG22-6 AWG 1.5-10 sq.mm 22-6 AWG

600 V 800 V 600 V

125 A 130 A65 A 57 A 65 A




Cat. No. Std. Pk.

CA702 50CA802 50

MT10 100



E220514 E220514 E220514

Distribution Block

Terminal Width

Height & Width

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block



Marking Tags (MT Type)

Warning Label

InputOutput

InputMax. Individual Output

InputOutput

InputOutput






CMDB4/X

6 mm

45 x 43 mm

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 800 V 600 V

30 A 32 A 35 A


Cat. No. H x W x L Outputs Std.(mm) Pk.

CMDB4/2 45 x 43 x 13.5 4 10CMDB4/3 45 x 43 x 19.5 6 10CMDB4/4 45 x 43 x 25.5 8 5CMDB4/10 45 x 43 x 61.5 20 5

Cat. No. Std. Pk.

CA702 50CA802 50

MT6 100

Screw clamp connection

CMDB10/X

10 mm

43 x 47 mm

12 mm

Polyamide 6.6

22-6 AWG 1.5-10 sq.mm 20-6 AWG

600 V 800 V 600 V

65 A 57 A 65 A




Cat. No. Std. Pk.

CA702 50CA802 50

MT10 100


CMDB6/X

8 mm

43 x 47 mm

12 mm

Polyamide 6.6

22-8 AWG 1.5-6 sq.mm 22-8 AWG

600 V 800 V 600 V

50 A 41 A 50 A




Cat. No. Std. Pk.

CA702 50CA802 50

MT8 100

SWL6 100


CMDB blocks are the modifiedversion of CDB terminal blockswithout central incoming ter-minal connections.

Distribution Block

E220514 E220514 E220514


CONNECTOR TO TERMINALBLOCK MODULESCompact and reliable connections betweenhigh density connectors and high qualityscrew-cage clamp terminal blocks; DIN Railmountable

PLUGGABLESLIMLINE RELAYSNeed Text

DIODE MODULES &COMPONENT CARRIERSAdd additional components to build circuitsand diode modules mounted on 35 or32mm DIN Rails.

MONITORING PROTECTIONMODULESSpecial purpose components connected toscrew-cage clamp terminal blocks; DIN Railmountable.

POWER SUPPLIESBasic and High Performance Series. DINRail mountable units are available with 12or 24VDC output, 15 to 60 Watts and reg-ulated outputs.

SOLID STATE I/O MODULESInput/Output Modules (both AC and DC)provided on a DIN mountable module.Bussed and isolated versions available.

RELAY MODULESTraditional relay modules from 1-16 chan-nels. Available in several voltages (AC &DC), isolated or bussed systems. DIN Railmounted.

SAFETY RELAY MODULESForce-guided contact modules available in1-16 channels, 12 and 24VDC coils andisolated or bussed systems. All mountableon 32 or 35mm DIN Rails.

CUSTOM MODULESAltech provides quick turn-key customdesigns and competitive solutions.

GENERAL PURPOSE/INTERFACE RELAYSA selection of DIN Rail mountable generalpurpose relays available for up to 12 A @250 Volts.

MOUNTING TRACKSDIN Rail or panel mount mounting trackssecure standard or custom printed circuitboards in control panels or cabinets.

I/O MODULE CARRIERSAccepts industry standard I/O modules.LED indicator and fuse protection includedon carrier.

We have a full line of standard and customInterface Modules and Power Supplies.

Contact AltechToday to learn more!

Part Number:

Approvals

Current Rating

Voltage Rating

SCCR

No. of InputsWire RangeTorque

ScrewTypeNo. of Outputs

Wire RangeTorqueWire RangeTorque

ScrewTypeOptionalMarkingTag**(for DB16and DB35)

Dimensions:

DB16*

80A 80A

600V AC 690V AC

10kA

1 18-4 AWG 6-16mm2

13.5lb.-in. 1.5Nm

Pozi Drive 26 6

(2x)8-4 AWG (2x)6-16mm2

13.5lb.-in. 1.5Nm(4x)14-10 AWG (4x)2.5-6mm2

7.2lb.-in. 0.8NmPozi Drive 2

MT2**

38049

80A 80A

600V AC 690V AC

100kA

1 18-4 AWG 6-16mm2

13.5lb.-in. 1.5Nm

Pozi Drive 26 6

(2x)8-4 AWG (2x)6-16mm2

13.5lb.-in. 1.5Nm(4x)14-10 AWG (4x)2.5-6mm2

7.2lb.-in. 0.8NmPozi Drive 2

DB35*

115A 125A

600V AC 690V AC

10kA

1 18-2 AWG 10-35mm2

31lb.-in. 3.5Nm

Pozi Drive 26 6

14-6 AWG 2.5-16mm2

17.5lb.-in. 2Nm

Pozi Drive 2

MT2**

38041

115A 125A

600V AC 690V AC

100kA

1 18-2 AWG 10-35mm2

13.5lb.-in. 3.5Nm

Pozi Drive 26 6

14-6 AWG 2.5-16mm2

17.5lb.-in. 2Nm

Pozi Drive 2


DB16• Quick mountingand wiring

• IP20 Finger Safe• DIN Rail or Panel Mount• Blocks fit with other DINRail mountable modulardevices (height 95mm,depth 44.5mm)

• Accessories increase thenumber of outputs withonly one input (appliesonly to 38041 and 38032)

• No caps to open / remove• Material

Housing: PolyamideMetal Body: Brass

Fork Type Busbar38045

38041

UL File E220514 UL File E98082 UL File E220514 UL File E98082

Accessories: ForkType BusbarPart No: 38045 to jump 2 Blocks

38046 to jump 8 Blockscan be cut

38041

38049 DB35 38041

One Phase Power Distribution Block

* Available in colors. Color Ordering SuffixRed RBlue BUBlack BLOrange OGreen GYellow YWhite WBeige BGDark Brown DB





43 mm(1.69 in)

38.5 mm(1.52 in)

45 mm(1.77 in)

58m

m(2

.28

in)

5.2 mm(0.20 in)

17.4 mm(0.69 in)

13.8 mm(0.54 in)

19.9 mm(0.78 in)

5.2 mm(0.20 in)

71m

m(2

.80

in)

43 mm(1.69 in)

38.5 mm(1.52 in)

45 mm(1.77 in)

58m

m(2

.28

in)

5.2 mm(0.20 in)

17.4 mm(0.69 in)

13.8 mm(0.54 in)

19.9 mm(0.78 in)

5.2 mm(0.20 in)

71m

m(2

.80

in)

38032

38032

160A 160A

600V AC 690V AC

100kA

1 18-2/0AWG 10-70mm2

35.5lb.-in. 4NmHex 5

6 614-6 AWG 2.5-16mm2


38076

Part Number:

Approvals

Current Rating

Voltage Rating

SCCR



Wire RangeTorque

ScrewType

Dimensions:

38076

115A 125A

600V AC 690V AC

100kA

1 18-2 AWG 10-35mm2

53lb.-in. 6NmHex 4

10 1014-4 AWG 2.5-16mm2


38074

38074

175A 175A

600V AC 690V AC

100kA

1 16-2/0AWG 16-70mm2

53lb.-in. 6NmHex 5

10 1014-4 AWG 2.5-16mm2


Copper Jumper Bar3803221

38032

UL File E98082 UL File E98082 UL File E98082

Accessories: Copper Jumper Bar(6x15 mm)

Part No: 3803221 for 2 Blocks3803231 for 3 Blocks3803241 for 4 Blockscan be cut

38032



38020 38019

Part Number:

Approvals

Current Rating

Voltage Rating

SCCR



Wire RangeTorqueWire RangeTorqueWire RangeTorque

ScrewType

Dimensions:

38020 38019

230A 250A 310A 400A

600V AC 690V AC 600V AC 690V AC

100kA 100kA

1 1 1 12-4/0AWG 35-120mm2 3/0-350mcm 95-185mm2

170lb.-in. 19Nm 230lb.-in. 25NmHex 6 Hex 8

11 11 11 11(2x) 14-2AWG (2x) 2.5-35mm2 (2x) 14-2AWG (2x) 2.5-35mm2

31lb.-in. 3.5Nm 31lb.-in. 3.5Nm(5x) 14-6AWG (5x) 2.5-16mm2 (5x) 14-6AWG (5x) 2.5-16mm2

17.5lb.-in. 2Nm 17.5lb.-in. 2Nm(4x) 14-8AWG (4x) 2.5-10mm2 (4x) 14-8AWG (4x) 2.5-10mm2

17.5lb.-in. 2Nm 17.5lb.-in. 2Nmstandard screwdriver standard screwdriver

UL File E98082 UL File E98082

• Quick mounting and wiring• IP20 Finger Safe• DIN Rail or Panel Mount• Blocks fit with other DIN Railmountable modular devices(height 95mm, depth 44.5mm)

• Accessories increase thenumber of outputs with onlyone input.

• No caps to open or remove• Material




38075 38073

Part Number:

Approvals

Current Rating

Voltage Rating

SCCR



Wire RangeTorque

ScrewType

Dimensions:

38075 38073

115A 115A 175A 175A

600V AC 690V AC 600V AC 690V AC

100kA 100kA

3x1 3x1 3x1 3x18-2AWG 10-35mm2 8-2/0AWG 10-70mm2

31lb.-in. 3.5Nm 35.5lb.-in. 4NmHex 4 Hex 5

3x6 3x6 3x6 3x614-4AWG 2.5-16mm2 14-4AWG 2.5-16mm2

17.5lb.-in. 2Nm 17.5 lb.-in. 2NmHex 3 Hex 3

3 Pole 3 Pole

• Quick mounting and wiring• IP20 Finger Safe• DIN Rail or Panel Mount• Blocks fit with other DIN Railmountable modular devices

• Same compact size forboth ratings

• No caps to open or remove• Material


UL File E98082 UL File E98082

Three Phase Power Distribution Block


• Quick mountingand wiring

• IP20 Finger Safe• DIN Rail or Panel Mount• No caps to open or remove• Material

Housing: PolyamideMetal Body: Aluminum

38064 38057

Part Number:

Approvals

Current Rating

Voltage Rating



Wire RangeTorque

ScrewType

Dimensions:

38064

175A 175A

600V AC 690V AC

1 114-1AWG 2.5mm2-50mm2


1 114-1AWG 2.5mm2-50mm2


38057

400A 400A

600V AC 690V AC

1 16AWG-400MCM 16mm2-185mm2

221lb.-in. 25NmHex 10

1 16AWG-400MCM 16mm2-185mm2


38059

800A 800A

600V AC 690V AC

2 23AWG-600MCM 25-300mm2


2 23AWG-600MCM 25-300mm2


59.6

mm

(2.3

5in)

25.4 mm(1.0 in)

50 mm(1.97 in)

72.3

mm

(2.8

5in)

34.7

mm

(1.3

7in)

43.2

mm

(1.7

0in)

39 mm [1.54 in]

7 mm[0.28 in]

145.

5m

m[5

.73

in]

7.5 mm[0.30 in]

124.

4m

m[4

.90

in]

12 mm [0.47 in]

7 mm [0.28 in]

80.5 mm [3.17 in]

53.5 mm[2.11 in]

145

mm

[5.7

1in

]

129

mm

[5.0

8in

]

72 mm [2.83 in]

80.5 mm [3.17 in]

38059

UL File E98082 UL File E98082 UL File E98082

Splicer Blocks


CTT2.5UK/J/T/E

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Current Carrying Material

Type of Connection

Wire Range

Voltage Rating

Current Rating

Torque

Terminal Block

End Plate

Isolation Plate


End Clamp

MarkingTags(MTType)

10 mm

45 x 43 mm

9 mm

Polyamide 6.6

*4 screw clamps

24-12 AWG

300 V

10 A

7 lb-in

Cat. No. Std. Pk.

CTT2.5UK 50CTT2.5UJ 50CTT2.5UT 50CTT2.5UE 50

EP2.5/4UN 50

PP2.5/4UN 50

CA802 100CA702 100

CA509/K5

Altech thermocouple terminalblocks are designed for use intemperature measuring circuits.

The current carrying part of theterminal blocks have the samematerial (according to DIN437134and DIN43714) which is used forcompensating cables in the tem-perature measurement circuit (upto 200°C).

The terminal block is marked forthe respective type of thermocou-ple which enables easy identifica-tion for wiring.

*• CTT2.5UK ‘K’ type -Chromel (NiCr)Alumel (NiAl)

• CTT2.5UJ ‘J’ type -Iron (Fe)Constantan (CuNi)

• CTT2.5UT ‘T’ type -Copper (Cu)Constantan (CuNi)

• CTT2.5UE ‘E’ type -Chromel (NiCr)Constantan (CuNi)

Thermocouple(Sensor)

MeasuringInstrument

ThermocoupleTerminal Block

ThermocoupleTerminal Block

ReferenceJunction

Compensating Cable Supply Cable

Thermocouple Blocks

Diode Specifications

Diode 1N 4007

Diode Reverse Voltage 1000 V

Diode Current 1 A

1

3 4

C

2

1

3 4C

2

1

3 4C

2

D1

D2

D3

CDL4U(E)D1/D2 CDL4U(E)D3

6 mm

54 x 55.5 mm

300 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)D3 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/2 100CA705/3 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

6 mm

54 x 55.5 mm

300 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)D1 100CDL4U(E)D2 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/2 100CA705/3 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

With arc suppression circuit forcontactors and solenoid valves - DC

Diode circuit forreverse polarity protection

Altech offers different types ofterminals incorporating elec-tronic components for signalconverting, circuit protectionand status indication. Based oncustomer requirements, special-ly assembled terminals areoffered.





E220514 E220514


TerminalWidth

Height x Length

Terminal Voltage

Stripping Length

Insulation Material

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper

CurrentBars


MarkingTags




Indicator/ Diode Circuit

1

3 C

C

C

C

+4

2

1

3 -4

2

1

+3C C

C C

+4

2

1 2

+3 +4

1

3 +4

2

C

1

3 +4C

C

2

DD3DD1

DD2 DD4

D4 DD5


6 mm

54 x 55.5 mm

300 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)DD3 100CDL4U(E)DD4 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

6 mm

54 x 55.5 mm

300 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)DD1 100CDL4U(E)DD2 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

CDL4U(E)DD1/DD2 CDL4U(E)DD3/DD4

Diode circuit for lamp testing Diode circuit for lamp testing

6 mm

54 x 55.5 mm

12V~/24 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)DD5 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

6 mm

54 x 55.5 mm

12V~/24 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)D4 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

CDL4U(E)D4 CDL4U(E)DD5

Diode circuit for lamp testing withLED series resistance

Diode circuit for lamp testing withLED series resistance

E220514 E220514 E220514 E220514


CDL4U(E)N1 CDL4U(E)LD5* CDL4U(E)LD3*

6 mm

54 x 55.5 mm

24 V~, 48 V~, 120V~, 220V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)LD5* 50

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

6 mm

54 x 55.5 mm

110 V~ to 220 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)N1 50

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

AC voltage indicator with neon lamp

6 mm

54 x 55.5 mm

12 V~, 24 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)LD3* 50

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

AC/ DC voltage indicator with LEDAC voltage indicator with LED

1

3 4

2 1

3 4C +3 +4

+1

N1 LD5 LD3

* Add required voltage to part number as a suffix i.e. CDL4U(E)LD5/110 is for 110V.

E220514 E220514 E220514


TerminalWidth

Height x Length

Terminal Voltage

Stripping Length

Insulation Material

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



InternalJumper

CurrentBars


MarkingTags






+1

-3 -4

-1

+3 +4

+1

-3

C

C

-4

-1

+3 +4

-1

+3 +4

C

L1LD1

LD2

6 mm

54 x 55.5 mm

24 V–

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)LD1 50CDL4U(E)LD2 50

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

6 mm

54 x 55.5 mm

24V~, 48 V~

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)LD4* 50

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

CDL4U(E)LD4* CDL4U(E)LD1/LD2

AC/ DC voltage indicator with LED

6 mm

54 x 55.5 mm

6 V–, 24 V–, 60 V–

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(E)L1* 50CDL4U(E)L2* 50

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

CDL4U(E)L1/L2* CDL4U(O)

DC voltage indicator with LED Electronic Component CarrierDC voltage indicator with LED

6 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 400 V 600 V

25 A 32 A 35 A


Cat. No. Std. Pk.

CDL4U(O) 100

EPCDL4U 50

CA702 50CA802 50

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

MT2 100

L2

E220514 E220514 E220514 E220514


* Add required voltage to part number as a suffix i.e. CDL4U(E)LD5/110 is for 110V.

CDL4U(E)LA CDL4U(E)3LA

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Wire Range

Voltage Rating

Nominal Discharge Current

Peak Current

ResponseTime

Nominal Current

Capacitance

Application

Terminal Block

End Plate




12 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps

22-10 AWG

75, 90, 240, 600, 1000 V DC

20 KA (8/20µs)

–

100 ns

10A

<1.5 pf

For coarse line protection ofmeasuring, distributing or datacommunication interfaces.

Cat. No. Std. Pk.

CDL4U(E)LA75V 20CDL4U(E)LA90V 20CDL4U(E)LA230V 20CDL4U(E)LA600V 20CDL4U(E)LA1000V 20

EPCDL4U 50

CA702 50CA802 50

MT2 100

18 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps

22-10 AWG

90, 250, 350, 450 V DC

10 KA (8/20µs)

–

100 ns

5A

<1.0 pf

For simultaneous protection of linesagainst transversal (line/line) andlongitudinal (line/earth) surge.

Cat. No. Std. Pk.

CDL4U(E)3LA90V 20CDL4U(E)3LA230V 20CDL4U(E)3LA350V 20CDL4U(E)3LA600V 20

EPCDL4U 50

CA702 50CA802 50

MT2 100

Lightning Arrestor 3 Pole Lightning Arrestor






In applications where circuitprotection against transientovervoltage is required, AltechSurge Suppressor TerminalBlocks with built-in electroniccomponents are recommended.

These terminals are designed toprotect a single line against alongitudinal (line / earth) surge,thereby protecting distributionand inputs.

Note:CDL4U(E)SDU - For D.C.Application

CDL4U(E)SDB - For A.C.Application

A - Anode

K - Cathode

* Add required voltage topart number as a suffixi.e. CDL4U(E)LA/75 is for 75V.

Surge Suppressor


SDBSDUA SDUK

CDL4U(E)MOV1 CDL4U(E)SD CDL4U(E)RC

12 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps

22-10 AWG

12-48V DC / 12-160V AC**

1.5 KA

–

1 ns DC / 5 ns AC

10A

–

For fine protection of data interfaces, sen-sors, contacts, etc.

Cat. No. Std. Pk.

CDL4U(E)SDUA15V 20CDL4U(E)SDUA24V 20CDL4U(E)SDUA48V 20CDL4U(E)SDUK15V 20CDL4U(E)SDUK24V 20CDL4U(E)SDUK48V 20CDL4U(E)SDB15V 20CDL4U(E)SDB24V 20CDL4U(E)SDB48V 20CDL4U(E)SDB160V 20

EPCDL4U 50

CA702 50CA802 50

MT2 100

18 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps

22-10 AWG

250 V AC / 330 V DC

20A

–

–

10A

0.1 µf or 0.22 µf2

For protection of DC solenoid valvesand contactors

Cat. No. Std. Pk.

CDL4U(E)RC0.1 20CDL4U(E)RC0.22 20

EPCDL4U 50

CA702 50CA802 50

MT2 100

12 mm

54 x 55.5 mm

9 mm

Polyamide 6.6

4 screw clamps

22-10 AWG

130 V AC*

–

2kA-6.5kA (8/20µs)

<25ns

10A

100-20,000 pf

For protection from voltagesurge, spikes

Cat. No. Std. Pk.

CDL4U(E)MOV30V 20CDL4U(E)MOV60V 20CDL4U(E)MOV75V 20CDL4U(E)MOV130V 20CDL4U(E)MOV275V 20CDL4U(E)MOV460V 20CDL4U(E)MOV510V 20CDL4U(E)MOV625V 20CDL4U(E)MOV680V 20

EPCDL4U 50

CA702 50CA802 50

MT2 100

MOV Suppressor Diode RC Circuit

1 A fuse block is recommended to protect MOV terminals by disconnecting the faulted varistor. See pages 18-21 for fuse blocks.* Other voltages available upon request. Call Altech for voltage selection.** Phase to Phase / Phase to ground.

Surge Suppressor

CMT4For wire-to-wire connecting incontrol, automation, instrumen-tation and power distributionapplications.

Altech “miniature” terminalblocks offer tremendous spaceadvantage as demanded by cer-tain wiring configurations.

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition



InternalJumper


CurrentBars


ExternalJumper


6 mm

29 x 27 mm

9 mm

Polyamide 6.6

2 screw clamps & 1 tapped holefor cross connection

22-10 AWG 0.5-4 sq.mm 22-10 AWG

300 V 400 V 300 V

35 A 32 A 35 A


Cat. No. Std. Pk.

CMT4 100

EPCMT4 50

PPCMT4 50

CA602 100

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA747/2 100CA747/3 100CA747/4 100CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 100CA714/10 20

MT2 100










E220514


CGMT4

6 mm

28.5 x 27 mm

9 mm

Polyamide 6.6

2 screw clamps

22-10 AWG 0.5-4 sq.mm 22-10 AWG

32A


Cat. No. Std. Pk.

CGMT4 50

MT2 100

E220514

AEx eIIEx eII

Mini Feed-Through 15mm


Certain electrical and control sys-tems require protection by fuses.The terminal has a hinged carrierthat has a specially designedspace for a cartridge type glassfuse of size Ø5 x 20 or Ø5 x 25mm. The fuse can be engaged ordisengaged by the movement ofthe carrier.

Altech fuse terminals are alsoavailable with light indication -CSFL 4U (L). A specially de-signedbuilt-in circuit gives light indica-tion in the event of fuse blow out.


*Add required voltage to part number as a suffix, i.e. CSFL4U(L)/24 for 24V DC

Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Type of Fuse Used

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition



InternalJumper


CurrentBars


ExternalJumper

Marking Tags (MT Type)(MT Type on Lever)






CSFL4U CSFL4U(L)*

8 mm 43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25mm

22-10 AWG 22-10 AWG

600 V 600 V

6.3 A 10 A

7 lb-in 7 lb-in

Cat. No. Std. Pk. CSFL4U 100

EPCSFL4U 50

PPCSFL4U 50

CA602 100

CA711/2 100 CA711/3 50 CA711/4 50 CA711/10 20

MT8 100 MT2 100

8 mm 43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25mm

22-10 AWG 22-10 AWG

600 V 600 V

6.3 A 10 A

7 lb-in 7 lb-in

Cat. No. Std. Pk. CSFL4U(L)* 100

EPCSFL4U 50

PPCSFL4U 50

CA602 100

CA711/2 100 CA711/3 50 CA711/4 50 CA711/10 20

MT8 100 MT2 100

E220514 E220514


Mini Feed-Through Fuse Block, 5 x 20 and 5 x 25 mm

24V AC/DC, 48V AC/DC,110V AC/DC, 220V AC, 300V AC

EPCMB4

CMB4For use when space constraintsrequire extremely compactsolutions and internal jumpingis required.

Individual components can beused to build your own assem-blies. Just snap the requirednumber of terminal block com-ponents together and place aMounting Section on each end.

The CMB4 accepts internaljumpers and standard markingtags.

• Extremely compact andcost effective

• High density• Screw-cage clamp• Internal jumping provision• Polyamide 6.6• Standard color: gray

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

Mounting Section

Separator Plate

Mounting Screw*

InternalJumper


CurrentBars


ExternalJumper







6 mm

28 x 27 mm

9 mm

Polyamide 6.6

2screwclamps&1 tappedhole for cross connect.

22-10 AWG 0.5-4 sq.mm 22-10 AWG

300 V 400 V 300 V

35 A 32 A 35 A


Cat. No. Std. Pk.

CMB4 100

EPCMB4 50

SPCMB4 100

Any length M3 screw may be used.

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA747/2 100CA747/3 100CA747/4 100CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 100CA714/10 20

MT2 100

Dimensions mm (in.)CMB4

Mounting SectionEPCMB4

No. of HoleCat No. Poles Width (a) Spacing (b)CMB4/2 2 26 (1.02) 19 (0.75)CMB4/3 3 32 (1.26) 25 (0.98)CMB4/4 4 38 (1.50) 31 (1.22)CMB4/5 5 44 (1.73) 37 (1.46)CMB4/6 6 50 (1.97) 43 (1.69)CMB4/7 7 56 (2.20) 49 (1.93)CMB4/8 8 62 (2.44) 55 (2.17)CMB4/9 9 68 (2.68) 61 (2.40)CMB4/10 10 74 (2.91) 67 (2.64)CMB4/11 11 80 (3.15) 73 (2.87)CMB4/12 12 86 (3.39) 79 (3.11)CMB4/13 13 92 (3.62) 85 (3.35)CMB4/14 14 98 (3.86) 91 (3.58)CMB4/15 15 104 (4.09) 97 (3.82)CMB4/16 16 110 (4.33) 103 (4.06)CMB4/17 17 116 (4.57) 109 (4.29)CMB4/18 18 122 (4.80) 115 (4.53)CMB4/19 19 128 (5.04) 121 (4.76)CMB4/20 20 134 (5.28) 127 (5.00)CMB4/21 21 140 (5.51) 133 (5.24)CMB4/22 22 146 (5.75) 139 (5.47)CMB4/23 23 152 (5.98) 145 (5.71)CMB4/24 24 158 (6.22) 151 (5.94)

ba

* Any length M3 screw may be used.

Preassembled blocks arealso available for quickand easy installations.See Dimensions below.





E220514


Mini Feed-Through Panel Mount


CENC4 CENC16 CENC35A quick reliable solution forground, neutral or low volt-age distribution applica-tions. The Busbar Systemconsists of a busbar, busbarsupports, and screw clampterminals for terminatingwires

NEB 10 (10 x 3 mm) andNEB 6 (6 x 6 mm), tin platedcopper busbars are avail-able in one meter lengths.Both have a 140A currentcarrying capacity.

NES plastic support withfixing screws for holding 10x 3 & 6 x 6 busbar makesplacing of busbar an easytask. Busbars up to 200 mmlength should be supportedat ends by two busbar sup-ports. For busbars exceed-ing 200 mm length, it is rec-ommended to provide inter-mediate busbar support.Easy to operate CENCclamp secures wire to thebusbar.

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Current Rating*

Torque

Other Approvals

Terminal Block**

Busbar(10 x 3 mm)

Busbar(6 x 6 mm)

Plastic Supportwith Fixing Screw

End Clamp/Bus barsupport for rail mounting

MarkingTags(MTType)

7.5 mm 9.8 mm 14.5 mm

30 x 23.3 mm 36 x 23.3 mm 45 x 27.3 mm

12 mm 16 mm 16 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

1 screw clamp connection 1 screw clamp connection 1 screw clamp connection

22-10 AWG 0.5-6 sq.mm 22-12 AWG 10-4 AWG 6-16 sq.mm 10-6 AWG 8-2 AWG 10-35 sq.mm 8-2 AWG

35 A 41 A 80 A 76 A 125 A 125 A

14 lb-in 0.8 Nm 14 lb-in 14 lb-in 2.0 Nm 17.5 lb-in 25 lb-in 2.5 Nm 25 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CENC4 50 CENC16 50 CENC35 50

NEB10 1 m NEB10 1 m NEB10 1 m


NES 50 NES 50 NES 50

CA202 50 CA202 50 CA202 50

MT5 100 MT6 100 MT6 100

* 140A current carrying capacity of busbar should be takeninto account while connecting loads.

** Consult for other available colors.

E220514 E220514 E220514

Busbar System

CSTSN4U CSTSN5U

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



Protective Coverfor covering

Protective Coverin Length

Insulated RemovableJumpers

Insulated PermanentJumpers


2Terminal3Terminal

100 mm200 mm300 mm

2 way3 way4 way

2 way3 way4 way

17 mm

39.5 x 50 mm

12 mm

Polyamide 6.6

2 screw connectionfor M4 ring/fork lugs

22-6 AWG 1.5-10 sq.mm 22-6 AWG

600 V 800 V 600 V

65 A 57 A 65 A


Cat. No. Std. Pk.

CSTSN4U 100

EPCSTSN5U 50

CA702 50CA802 50

CSTSPC1 100CSTSPC1-1 100

CSTSPC1-2 10CSTSPC1-3 10CSTSPC1-4 10

CA514/1-2 100CA514/1-3 50CA514/1-4 50

CA514/3-2 100CA514/3-3 50CA514/3-4 50

MT2 100

Altech DIN rail mounting StudType Terminal Blocks are pre-ferred for the connections thatare subjected to very severevibrations.

The wire is crimped to a ring /fork type lug and is screwed onto the flat current bar in termi-nal.The range includes terminalblocks for wires of size 22-4AWG.

Jumpering can be achievedwith the aid of externaljumpers. The jumpers are insu-lated to make them shock proof.The terminal blocks have mark-er holding recess to accommo-date MT type marking tags.

It is recommended to use pro-tective covers in transparentplastic because assemblies ofthese terminals blocks are notfully covered.

17 mm

39.5 x 50 mm

12 mm

Polyamide 6.6


22-4 AWG 1.5-16 sq.mm 22-4 AWG

600 V 800 V 600 V

80 A 76 A 80 A

17.5 lb-in 2.0 Nm 17.5 lb-in

Cat. No. Std. Pk.

CSTSN5U 100

EPCSTSN5U 50

CA702 50CA802 50



CA514/1-2 100CA514/1-3 50CA514/1-4 50

CA514/3-2 100CA514/3-3 50CA514/3-4 50

MT2 100






E220514 E220514

Stud Type Block


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate



Protective Coverfor covering

Protective Coverin Length

Insulated RemovableJumpers



2Terminal3Terminal

100 mm200 mm300 mm

2 way3 way4 way

2 way3 way4 way

CSTSB4U CSTSB5U

17 mm

39.5 x 50 mm

12 mm

Polyamide 6.6


22-6 AWG 1.5-10 sq.mm 22-6 AWG

600 V 800 V 600 V

65 A 57 A 65 A


Cat. No. Std. Pk.

CSTSB4U 100

EPCSTN5U 50

CA702 50CA802 50



CA514/1-2 100CA514/1-3 50CA514/1-4 50

CA514/3-2 100CA514/3-3 50CA514/3-4 50

MT2 100

17 mm

39.5 x 50 mm

12 mm

Polyamide 6.6


22-4 AWG 1.5-16 sq.mm 22-4 AWG

600 V 800 V 600 V

80 A 76 A 80 A

17.5 lb-in 2.0 Nm 17.5 lb-in

Cat. No. Std. Pk.

CSTSB5U 100

EPCSTN5U 50

CA702 50CA802 50



CA514/1-2 100CA514/1-3 50CA514/1-4 50

CA514/3-2 100CA514/3-3 50CA514/3-4 50

MT2 100

E220514 E220514

Stud Type Block

Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

Stud Size / Operated by

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate


End Stopfor ordering info.refer to page 72

RemovableShorting Link

Insulated RemovableShorting Link

PermanantShorting Link


Marking Tags (K Type)

2 way3 way4 way

2 way3 way4 way

2 way3 way4 way

2 way3 way4 way

11 mm

50.5 x 46 mm

10 mm

Polyamide 6.6

2 stud flat connection

M4 / Screwdriver

22-8 AWG 1.5-6 sq.mm 22-8 AWG

600 V 800 V 600 V

50 A 41 A 50 A


Cat. No. Std. Pk.

STH4 100

EPSTH4 50

CA702 100CA802 50

CA512/13-2 100CA512/13-3 50CA512/13-4 50

CA514/13-2 100CA514/13-3 50CA514/13-4 50

CA512/14-2 100CA512/14-3 50CA512/14-4 50

CA514/14-2 100CA514/14-3 50CA514/14-4 50

CA509/K10 100


STH4

11 mm

50.5 x 86 mm

10 mm

Polyamide 6.6


M4 / Screwdriver

22-8 AWG 1.5-6 sq.mm 22-8 AWG

600 V 800 V 600 V

50 A 41 A 35 A


Cat. No. Std. Pk.

STH4DT 100

EPSTH4DT 50

CA702 100CA802 50

CA512/13-2 100CA512/13-3 50CA512/13-4 50

CA514/13-2 100CA514/13-3 50CA514/13-4 50

CA512/14-2 100CA512/14-3 50CA512/14-4 50

CA514/14-2 100CA514/14-3 50CA514/14-4 50

CA509/K10 100

STH4DT

22 mm

50.5 x 86 mm

10 mm

Polyamide 6.6


M4 / Screwdriver

22-8 AWG 1.5-6 sq.mm 22-8 AWG

600 V 800 V 300 V

10 A 10 A 25 A


Cat. No. Std. Pk.

STH4DTSH 100

EPSTH4DT 50

CA702 100CA802 50

CA512/13-2 100CA512/13-3 50CA512/13-4 50

CA514/13-2 100CA514/13-3 50CA514/13-4 50

CA512/14-2 100CA512/14-3 50CA512/14-4 50

CA514/14-2 100CA514/14-3 50CA514/14-4 50

CA509/K10 100

STH4DTSHSTH Series TerminalBlocks are preferred forapplication where the con-nections are subjected tosevere vibration. The wireis crimped to a ring / forklug and is screwed on tothe flat current bar of theTerminal Block. The hingedcarrier should be lifted toinsert the lugs and thenfastened to complete theconnection.

By virtue of the hingeddesign, the TerminalBlocks apart from shroud-ing the live parts, provid-ing IP 20 (Finger Safe) pro-tection, saves consider-able time in wiring.

Two Lugs can be connect-ed to the Terminal, withoutsacrificing the safety ofthe Terminal Block.

STH4DT Disconnect & TestTerminal Block is used formeasuring, control andregulatory circuits. Theyprovide a clear functionaladvantage for deviceshaving utility instrumentsand associated transform-ers.

Socket Headed Screws actas test monitoring pointon either side of theTerminal Block. Discon-nection is achieved bymeans of a slide link oper-ated with a Screw Driver.

STH4DTSH Terminal Blockhas 2 STH4DT TerminalBlock shorted to achieveswitchable cross connec-tion (on one side).

Note: The disconnectingdevice is not suitable forinterrupting load. The sup-ply must be switched offbefore operating the slidelink / moving the hingedcarrier.

Hinge Type Stud Block

E220514 E220514 E220514


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block



Protective Cover

Marker Holder

InternalJumper

MarkingTags (KType)

2 way3 way4 way

25 mm

62 x 113 mm

18 mm / M6

Polyamide 6.6

2 bolts for connection

8-2 AWG 16-35 sq.mm 8-2 AWG

600 V 1000 V 600 V

130 A 125 A 130 A


Cat. No. Std. Pk.

PTB35 100

CA702 100CA102 50CA202 50

PSPTB35 40

MHPTB35 40

CA703/9 10CA704/9 10CA705/9 10

CA509/K9 100

PTB35

25 mm

65 x 169 mm

18 mm / M6

Polyamide 6.6

2 bolts for connection

8-2 AWG 16-35 sq.mm 8-2 AWG

600 V 1000 V 600 V

130 A 125 A 130 A


Cat. No. Std. Pk.

PTB35SH 100

CA702 100CA102 50CA202 50

CA703/9 10CA704/9 10CA705/9 10

CA509/K9 100

PTB35SHPTB seriesTerminal Blocks are pre-ferred for application using wiresof large cross section. The Wire iscrimped to a ring / fork lug and isscrewed on to the flat current barof the Terminal Block. Speciallydesigned Mounting Feet holds theTerminal Block rigidly on to theMounting Rail.

Two Lugs of 35 sq.mm can be con-nected to theTerminal Block, with-out sacrificing the safety of theTerminal Block. Hinged ProtectiveCover makes the Terminal Blockshock proof (finger safe) and hasmarker recess to accept markingtag.

TheTerminal Blocks can be stackedtogether by pressing the adjacentTerminal Blocks firmly*. InPTB35SH series Terminal Blocks,adjacent terminals can be shortedby removing a thin wall partitionand using 2/3/4 way shorting link.

Optional Marker Holder MHPTB35can be used for installing markingtags on the Terminal Blocks with-out protective covers.

* M3 Screw of desired length withnut can be used optionally tosecure the stack.

Marker Holder

Power Block


➀UL ➀UL

CSC6T1-2

8 mm

45 x 94 mm

15 mm

Polyamide 6.6

3 spring clamps & 2 slots for interconnection

22-8 AWG 0.5-6 sq.mm. 22-8 AWG

600V 800V 600V

50A 41A 50A

Cat. No. Std. Pk.

CSC6T1-2 50

EPCSC6T1-2 50

CA702 50CA802 50

CA801/3 100CA801/3-3 100

CA901/3 100

MT8 100MT6F 100

ADL2.5

5 mm

50 x 79.5 mm

14 mm

Polyamide 6.6


22-12 AWG 2.5 sq.mm. 22-12 AWG

300V 800V 300V

20A 24A 25A

Cat. No. Std. Pk.

ADL2.5 50

EPADL2.5 50

CA702 50CA802 50

CA801/1 100CA801/1-3 100

CA901/1 100

MT5 100MT6F 100

CSC4T2-2

6 mm

42 x 105 mm

13 mm

Polyamide 6.6


22-12 AWG 0.5-4 sq.mm. 22-12 AWG

600V 800V 600V

25A 32A 25A

Cat. No. Std. Pk.

CSC4T2-2 50

EPCSC4T2-2 50

CA702 50CA802 50

CA801/2 100CA801/2-3 100

CA901/2 100

MT6 100MT6F 100

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Plate



Jumpers AdjacentAlternate

Push in typewire jumper

MarkingTags(MTType)

E220514 E220514 E220514


Feed-Through & Multi-Connection Spring Clamp


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Tyoe of fuse used

LED Voltage

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Plate



Insulated Jumper(2 pole)

MarkingTags(MTType)

ASF4Altech offers ‘Screwless’ SpringClamp FuseTerminal Blocks.

The terminal has a moving typehinged carrier that has speciallydesigned space for cartridgetype glass fuse of size Ø 5 x 20or Ø 5 x 25 mm.The fuse can beengaged or disengaged by themovement of the carrier.

Cross connection is possiblewith specially designed push-intype jumpers.

8 mm

60 x 86 mm

16 mm

Polyamide 6.6


Ø5x20, Ø5x25 mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 6.3 A

Cat. No. Std. Pk.

ASF4 100

EPASF4 50

CA702 50CA802 50

CA801/7 100

MT8 100

ASF4(L)*

8 mm

60 x 86 mm

16 mm

Polyamide 6.6


Ø5x20, Ø5x25 mm

24V AC/DC, 48V AC/DC110V AC/DC, 220V AC

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 6.3 A

Cat. No. Std. Pk.

ASF4(L)* 100

EPASF4 50

CA702 50CA802 50

CA801/7 100

MT8 100

*Add required voltage to part number as a suffix. i.e. ASF4(L)/24 for 24V AC/DC.





E220514 E220514

Fuse Spring Clamp, 5 x 20 and 5 x 25mm

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block


MarkingTags(MTType)

CSCG2.5T CSCG4TAltech offers ‘Screwless’ SpringClamp GroundTerminal Blocks.Specially designed alloy feethelps in achieving very lowcontact resistance and vibrationproof grounding.

CSCG series terminals can bemounted on Din 35 rail alongwith other terminal blocks ofCSC series. The terminal blockprofile matches with that ofCSC terminal block of samewire size.

Special features of CSCG termi-nal blocks are:

• Vibration proof grounding

• Very low contactresistance because ofspecial alloy feet

• Drop-on groundingconnection

• Spring clamp to acceptsolid and stranded wire

5 mm

36 x 58 mm

15 mm

Polyamide 6.6

2 spring clamp connection,grounding through alloy feet

22-14 AWG 0.5-2.5 sq.mm 22-14 AWG

800 V

24 A

Cat. No. Std. Pk.

CSCG2.5T 100

MT5 100

6 mm

42 x 65 mm

13 mm

Polyamide 6.6


22-12 AWG 0.5-4 sq.mm 22-12 AWG

800 V

32 A

Cat. No. Std. Pk.

CSCG4T 100

MT6 100

*E220514 E220514


Ground Spring Clamp


CSCG6T

8 mm

45 x 72 mm

15 mm

Polyamide 6.6


22-8 AWG 0.5-6 sq.mm 22-8 AWG

800 V

41 A

Cat. No. Std. Pk.

CSCG6T 50

MT8 100

CSCG10T CSCG16T

10 mm

50 x 75 mm

18 mm

Polyamide 6.6


16-6 AWG 1.5-10 sq.mm 16-6 AWG

800 V

57 A

Cat. No. Std. Pk.

CSCG10T 50

MT10 100

E220514

12 mm

58 x 82 mm

20 mm

Polyamide 6.6


16-6 AWG 1.5-16 sq.mm 16-6 AWG

800 V

76 A

Cat. No. Std. Pk.

CSCG10T 50

MT12 100

Ground Spring Clamp


➀UL ➀UL


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Plate

Partition Plate



Jumpers Adjacent

Jumpers Alternate


Step DownJumper

MarkingTags(KType)

These Terminal Bocks arean ideal choice for compactjunction boxes having limi-tations of space and height.

A major advantage ofAngular Terminal Blocksover the top wire entryTerminal Blocks is that theirprofile remains the sameacross the entire range ofFeed Through, MultipleConnection, Ground andGround Multiple Connec-tionTerminal Blocks.

The other advantagesinclude: Angular entry ofwires saving in conductorlength, marking / identifica-tion facility on the center(top) of the block,Multiplication of connec-tions through bridging.

Step Down shorting linksare used for shorting springclamp Terminal Blocks ofdifferent sizes. For moredetails refer to page 77.

AS2.5

5 mm

42 x 54 mm

16 mm

Polyamide 6.6

2 spring clamps& 2 slots for interconnection

22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG

600V 800 V 600 V

25 A 24 A 25 A

Cat. No. Std. Pk.

AS2.5 100

EPAS2.5 50

CA702 50CA802 50

CA801/1 100

CA801/1-3 100

CA901/1 100

CA901/5 100CA901/6 100

MT5 100MT6F 10

E220514

AS4

6 mm

42 x 61.5 mm

14 mm

Polyamide 6.6


22-10 AWG 0.5-4 sq.mm. 22-10 AWG

600V 800 V 600 V

35 A 32 A 35 A

Cat. No. Std. Pk.

AS4 100

EPAS4 50

CA702 50CA802 50

CA801/2 100

CA801/2-3 100

CA901/2 100

CA901/4 100CA901/6 100

MT6 100MT6F 10

Angular Feed-Through Spring Clamp


➀UL

seepage 78


AS6

8 mm

48 x 74 mm

15 mm

Polyamide 6.6


22-8 AWG 0.5-6 sq.mm. 22-8 AWG

600V 800 V 600 V

50 A 41 A 50 A

Cat. No. Std. Pk.

AS6 50

EPAS6 50

CA702 50CA802 50

CA801/3 100

CA801/3-3 100

CA901/3 100

CA901/4 100CA901/5 100

MT8 100MT6F 10

AS2.5/3

5 mm

42 x 54 mm

12 mm

Polyamide 6.6


22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG

600V 800 V 600 V

25A 24 A 25 A

Cat. No. Std. Pk.

AS2.5/3 100

EPAS2.5 50

CA702 50CA802 50

CA801/1 100

CA801/1-3 100

CA901/1 100

CA901/5 100CA901/6 100

MT5 100MT6F 10

E220514

AS2.5/4

5 mm

42 x 54 mm

12 mm

Polyamide 6.6

4 spring clamp connection

22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG

600V 800 V 600 V

25 A 24 A 25 A

Cat. No. Std. Pk.

AS2.5/4 100

EPAS2.5 50

CA702 50CA802 50

MT5 100MT6F 10

E220514



➀UL


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Plate

Partition Plate



Jumpers Adjacent

Jumpers Alternate


Step DownJumper

MarkingTags(KType)

AS4/3

6 mm

42 x 61.5 mm

14 mm

Polyamide 6.6


22-10 AWG 0.5-4 sq.mm. 22-10 AWG

600V 800 V 600 V

35 A 32 A 35 A

Cat. No. Std. Pk.

AS4/3 100

EPAS4 50

CA702 50CA802 50

CA801/2 100

CA801/2-3 100

CA901/2 100

CA901/4 100CA901/6 100

MT6 100MT6F 10

AS4/4

6 mm

42 x 61.5 mm

14 mm

Polyamide 6.6

4 spring clamp connection

22-10 AWG 0.5-4 sq.mm. 22-10 AWG

600V 800 V 600 V

35 A 32 A 35 A

Cat. No. Std. Pk.

AS4/4 100

EPAS4 50

CA702 50CA802 50

MT6 100MT6F 10

AS6/3

8 mm

42 x 74 mm

15 mm

Polyamide 6.6


22-8 AWG 0.5-6 sq.mm. 22-8 AWG

600V 800 V 600 V

50 A 41 A 50 A

Cat. No. Std. Pk.

AS6/3 50

EPAS6 50

CA702 50CA802 50

CA801/3 100

CA801/3-3 100

CA901/3 100

CA901/4 100CA901/6 100

MT8 100MT6F 10



➀UL ➀UL ➀UL

seepage 78


Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Plate


Marking Tags

Besides having angularwire entry, these TerminalBlocks have speciallydesigned alloy feet whichhelp in achieving very lowcontact resistance andvibration proof groundingwith DIN rails. They aregreen / yellow colorcoded as per industrystandards.

AGT2.5

5 mm

42 x 54 mm

16 mm

Polyamide 6.6


22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG

800 V 600 V

24 A

Cat. No. Std. Pk.

AGT2.5 100

EPAS2.5 50

MT5 100

E220514

AGT4

6 mm

42 x 61.5 mm

14 mm

Polyamide 6.6


22-10 AWG 0.5-4 sq.mm. 22-10 AWG

800 V 800 V

32 A

Cat. No. Std. Pk.

AGT4 100

EPAS4 50

MT6 100

Angular Ground / Earth Spring Clamp

E220514


Terminal Width

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Plate


Marking Tags(K Type)

AGT6

8 mm

48 x 74 mm

15 mm

Polyamide 6.6


22-8 AWG 0.5-6 sq.mm. 22-8 AWG

800 V 800 V

41 A

Cat. No. Std. Pk.

AGT6 50

EPAS6 50

MT8 100

AGT2.5/3

5 mm

42 x 54 mm

12 mm

Polyamide 6.6


22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG

800 V 600 V

24 A

Cat. No. Std. Pk.

AGT2.5/3 100

EPAS2.5 50

MT5 100

E220514

AGT2.5/4

5 mm

42 x 54 mm

12 mm

Polyamide 6.6


22-12 AWG 0.5-2.5 sq.mm. 22-12 AWG

800 V

24 A

Cat. No. Std. Pk.

AGT2.5/4 100

EPAS2.5 50

MT5 100

E220514


E220514


AGT4/3

6 mm

42 x 61.5 mm

14 mm

Polyamide 6.6


22-10 AWG 0.5-4 sq.mm. 22-10 AWG

800 V 800 V

32 A

Cat. No. Std. Pk.

AGT4/3 50

EPAS4 50

MT6 100

AGT4/4

6 mm

42 x 61.5 mm

14 mm

Polyamide 6.6


22-10 AWG 0.5-4 sq.mm. 22-10 AWG

800 V 800 V

32 A

Cat. No. Std. Pk.

AGT4/4 50

EPAS4 50

MT6 100

AGT6/3

8 mm

48 x 74 mm

15 mm

Polyamide 6.6


22-12 AWG 0.5-2.5 sq.mm. 22-8 AWG

800 V 800 V

41 A

Cat. No. Std. Pk.

AGT6/3 50

EPAS6 50

MT8 100


E220514 E220514E220514


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Section(set of left and right)


OperatingTool

MarkingTags(MTType)

5 mm

27 x 35 mm

14 mm

Polyamide 6.6

2 spring clamp connections

22-14 AWG 0.5-2.5 sq.mm 22-14 AWG

600 V 750 V 600 V

20 A 24 A 20 A

Cat. No. Std. Pk.

CSCP2.5T 100

EPCSCP2.5T 25

CA803/1 100

SCA2-5 1

MT4 100

10 mm

27 x 35 mm

14 mm

Polyamide 6.6


22-14 AWG 0.5-2.5 sq.mm 22-14 AWG

600 V 750 V 600 V

20 A 24 A 20 A

Cat. No. Std. Pk.

CSCP2.5T2 100

EPCSCP2.5T 25

CA803/1 100

SCA2-5 1

MT3 100

Altech “screwless” springclamp panel mount termi-nal blocks are an excellentsolution for extremelycompact wiring applica-tions.

These terminal blocks are“add-on” type and can becombined to form multi-pole assemblies. Thestacked assembly is fittedwith mounting end sec-tions on both ends foreasy installation on to thepanel.

The terminal has markerholding recessess on threesides to accept markingtags. Cross connection canbe achieved with the aid ofinsulated jumpers.

The CSCP2.5T2 panelmount terminal blockshave two connectionpoints on each side all withthe same potential.The ter-minals provide possibilityof further multiplicationthrough jumpering.

CSCP2.5T

EPCSCP2.5T

CSCP2.5T2EPCSCP2.5TCOLOR BLOCKS(other than grey standard)




E220514 E220514

Panel Mount Spring ClampCSCP2.5T CSCP2.5T2

CMT4For wire-to-wire connecting incontrol, automation, instrumen-tation and power distributionapplications.

Altech “miniature” terminalblocks offer tremendous spaceadvantage as demanded by cer-tain wiring configurations.

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition



InternalJumper


CurrentBars


ExternalJumper


6 mm

29 x 27 mm

9 mm

Polyamide 6.6

2 screw clamps & 1 tapped holefor cross connection

22-10 AWG 0.5-4 sq.mm 22-10 AWG

300 V 400 V 300 V

35 A 32 A 35 A


Cat. No. Std. Pk.

CMT4 100

EPCMT4 50

PPCMT4 50

CA602 100

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA747/2 100CA747/3 100CA747/4 100CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 100CA714/10 20

MT2 100










E220514


CGMT4

6 mm

28.5 x 27 mm

9 mm

Polyamide 6.6

2 screw clamps

22-10 AWG 0.5-4 sq.mm 22-10 AWG

32A


Cat. No. Std. Pk.

CGMT4 50

MT2 100

E220514

AEx eIIEx eII

Mini Feed-Through 15mm


Certain electrical and control sys-tems require protection by fuses.The terminal has a hinged carrierthat has a specially designedspace for a cartridge type glassfuse of size Ø5 x 20 or Ø5 x 25mm. The fuse can be engaged ordisengaged by the movement ofthe carrier.

Altech fuse terminals are alsoavailable with light indication -CSFL 4U (L). A specially de-signedbuilt-in circuit gives light indica-tion in the event of fuse blow out.


*Add required voltage topart number as a suffix, i.e.CSFL4U(L)/24 for 24V DC

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

LED Voltage

Type of Fuse Used

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

End Plate

Isolation Partition



InternalJumper


CurrentBars


ExternalJumper







CSFL4U CSFL4U(L)*

8 mm

43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 8 A


Cat. No. Std. Pk.

CSFL4U 100

EPCSFL4U 50

PPCSFL4U 50

CA602 100

CA711/2 100CA711/3 50CA711/4 50CA711/10 20

MT8 100MT2 100

8 mm

43 x 58 mm

9.5 mm

Polyamide 6.6

2 screw clamps

Ø5x20, Ø5x25mm

22-10 AWG 0.5-4 sq.mm 22-10 AWG

600 V 500 V 600 V

6.3 A 6.3 A 8 A


Cat. No. Std. Pk.

CSFL4U(L)* 100

EPCSFL4U 50

PPCSFL4U 50

CA602 100

CA711/2 100CA711/3 50CA711/4 50CA711/10 20

MT8 100MT2 100

E220514 E220514


Mini Feed-Through Fuse Block, 5 x 20 and 5 x 25 mm

24VAC/DC,48VAC/DC,110VAC/DC, 220VAC,300VAC

EPCMB4

CMB4For use when space constraintsrequire extremely compactsolutions and internal jumpingis required.

Individual components can beused to build your own assem-blies. Just snap the requirednumber of terminal block com-ponents together and place aMounting Section on each end.

The CMB4 accepts internaljumpers and standard markingtags.

• Extremely compact andcost effective

• High density• Screw-cage clamp• Internal jumping provision• Polyamide 6.6• Standard color: gray

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

Terminal Block

Mounting Section

Separator Plate

Mounting Screw*

InternalJumper


CurrentBars


ExternalJumper







6 mm

28 x 27 mm

9 mm

Polyamide 6.6

2screwclamps&1 tappedhole for cross connect.

22-10 AWG 0.5-4 sq.mm 22-10 AWG

300 V 400 V 300 V

35 A 32 A 35 A


Cat. No. Std. Pk.

CMB4 100

EPCMB4 50

SPCMB4 100

Any length M3 screw may be used.

CA727/2 100CA727/3 100CA727/4 100CA727/10 10

CA747/2 100CA747/3 100CA747/4 100CA747/10 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/10-A 100CA732/100 10

CA607/S/Q 100

CA714/2 100CA714/3 100CA714/4 100CA714/10 20

MT2 100

Dimensions mm (in.)CMB4

Mounting SectionEPCMB4

No. of HoleCat No. Poles Width (a) Spacing (b)CMB4/2 2 26 (1.02) 19 (0.75)CMB4/3 3 32 (1.26) 25 (0.98)CMB4/4 4 38 (1.50) 31 (1.22)CMB4/5 5 44 (1.73) 37 (1.46)CMB4/6 6 50 (1.97) 43 (1.69)CMB4/7 7 56 (2.20) 49 (1.93)CMB4/8 8 62 (2.44) 55 (2.17)CMB4/9 9 68 (2.68) 61 (2.40)CMB4/10 10 74 (2.91) 67 (2.64)CMB4/11 11 80 (3.15) 73 (2.87)CMB4/12 12 86 (3.39) 79 (3.11)CMB4/13 13 92 (3.62) 85 (3.35)CMB4/14 14 98 (3.86) 91 (3.58)CMB4/15 15 104 (4.09) 97 (3.82)CMB4/16 16 110 (4.33) 103 (4.06)CMB4/17 17 116 (4.57) 109 (4.29)CMB4/18 18 122 (4.80) 115 (4.53)CMB4/19 19 128 (5.04) 121 (4.76)CMB4/20 20 134 (5.28) 127 (5.00)CMB4/21 21 140 (5.51) 133 (5.24)CMB4/22 22 146 (5.75) 139 (5.47)CMB4/23 23 152 (5.98) 145 (5.71)CMB4/24 24 158 (6.22) 151 (5.94)

ba

* Any length M3 screw may be used.

Preassembled blocks arealso available for quickand easy installations.See Dimensions below.





E220514


Mini Feed-Through Panel Mount


TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Voltage Rating

Current Rating

Other Approvals

Terminal Block

End Section(set of left and right)


OperatingTool

MarkingTags(MTType)

5 mm

27 x 35 mm

14 mm

Polyamide 6.6


22-14 AWG 0.5-2.5 sq.mm 22-14 AWG

600 V 750 V 600 V

20 A 24 A 20 A

Cat. No. Std. Pk.

CSCP2.5T 100

EPCSCP2.5T 25

CA803/1 100

SCA2-5 1

MT4 100

10 mm

27 x 35 mm

14 mm

Polyamide 6.6


22-14 AWG 0.5-2.5 sq.mm 22-14 AWG

600 V 750 V 600 V

20 A 24 A 20 A

Cat. No. Std. Pk.

CSCP2.5T2 100

EPCSCP2.5T 25

CA803/1 100

SCA2-5 1

MT3 100

Altech “screwless” springclamp panel mount termi-nal blocks are an excellentsolution for extremelycompact wiring applica-tions.

These terminal blocks are“add-on” type and can becombined to form multi-pole assemblies. Thestacked assembly is fittedwith mounting end sec-tions on both ends foreasy installation on to thepanel.

The terminal has markerholding recessess on threesides to accept markingtags. Cross connection canbe achieved with the aid ofinsulated jumpers.

The CSCP2.5T2 panelmount terminal blockshave two connectionpoints on each side all withthe same potential.The ter-minals provide possibilityof further multiplicationthrough jumpering.

CSCP2.5T

EPCSCP2.5T

CSCP2.5T2EPCSCP2.5TCOLOR BLOCKS(other than grey standard)




E220514 E220514

Panel Mount Spring ClampCSCP2.5T CSCP2.5T2


High Temperature Ceramic EuroBlocks™

CB16CB4 CB6

W1

T T T

C2 W3

C3

D1

D2

W3

TT

HH

D1

D2

H

W2

H

W2

H

Dimensions mm

Note: All dimensions are shown in mm, to convert to inches please divide by 25.4.

Suitable for use in high tem-perature applications up to600°C (1112°F). Applicationsinclude hot melt glue guns,furnaces, heaters, processequipment and machinery.Terminal blocks are offeredwith mounting holes for panelmounting or free floatingapplications.

• Compact, space saving• Tubular screw clamp• Free float or panel mount• Temperature range:-40°C (-40°F) to600°C (1112°F)

• Standard color: white• MaterialHousing: SteatiteClamp: BrassScrews: Zinc plated steel

Ceramic

22-10 AWG 20-10 AWG

300V 300V

40 A 30 A

Cat. No. Std. Pk.

CB6/1 50

CB6/2H 50

CB6/3H 50

Insulation Material

Approvals

Wire Range

Voltage Rating

Current Rating

No. of Poles

1 (free floating)2 (free floating)2 (with mounting holes)3 (free floating)3 (with mounting holes)

Ceramic

20-6 AWG 18-6 AWG

300V 300V

76 A 65 A

Cat. No. Std. Pk.

CB16/2H 50

CB16/3H 50

Ceramic

24-12 AWG 24-12 AWG

300V 300V

30 A 20 A

Cat. No. Std. Pk.

CB4/1 50CB4/2 50CB4/2H 50CB4/3 50CB4/3H 50

W T H C D1 D2 Fixing StrippingScrew Length

CB4/1 1 POLE 23 11 18.5 * 6CB4/2 2 POLE 23 18 18.5 * 6CB4/2H 2 POLE 23 24 18.5 14.6 6 3.5 M3X16 6CB4/3 3 POLE 25 25 18.5 * 6CB4/3H 3 POLE 25.4 36 18.5 13 6 3.5 M3X16 6

CB6/1 1 POLE 25 12 19.5 * 6CB6/2H 2 POLE 25.5 26 19.5 12.6 6 M3X16 6CB6/3H 3 POLE 25.5 41 19.5 15 6 M3X16 6

CB16/2H 2 POLE 28 31 23.2 16.5 6 3.5 M3X20 8.5CB16/3H 3 POLE 27.5 48 23.2 17 6 3.5 M3X20 8.5

1 Pole 2 Pole 2 Pole withmounting hole

3 Pole 3 Pole withmounting hole

E220514 E220514 E220514


CENC4 CENC16 CENC35A quick reliable solution forground, neutral or low volt-age distribution applica-tions. The Busbar Systemconsists of a busbar, busbarsupports, and screw clampterminals for terminatingwires

NEB 10 (10 x 3 mm) andNEB 6 (6 x 6 mm), tin platedcopper busbars are avail-able in one meter lengths.Both have a 140A currentcarrying capacity.

NES plastic support withfixing screws for holding 10x 3 & 6 x 6 busbar makesplacing of busbar an easytask. Busbars up to 200 mmlength should be supportedat ends by two busbar sup-ports. For busbars exceed-ing 200 mm length, it is rec-ommended to provide inter-mediate busbar support.Easy to operate CENCclamp secures wire to thebusbar.

TerminalWidth

Height x Length

Stripping Length

Insulation Material

Type of Connection

Approvals

Wire Range

Current Rating*

Torque

Other Approvals

Terminal Block**

Busbar(10 x 3 mm)

Busbar(6 x 6 mm)

Plastic Supportwith Fixing Screw

End Clamp/Bus barsupport for rail mounting

MarkingTags(MTType)

7.5 mm 9.8 mm 14.5 mm

30 x 23.3 mm 36 x 23.3 mm 45 x 27.3 mm

12 mm 16 mm 16 mm

Polyamide 6.6 Polyamide 6.6 Polyamide 6.6

1 screw clamp connection 1 screw clamp connection 1 screw clamp connection

22-10 AWG 0.5-6 sq.mm 22-12 AWG 10-4 AWG 6-16 sq.mm 10-6 AWG 8-2 AWG 10-35 sq.mm 8-2 AWG

35 A 41 A 80 A 76 A 125 A 125 A

14 lb-in 0.8 Nm 14 lb-in 14 lb-in 2.0 Nm 17.5 lb-in 25 lb-in 2.5 Nm 25 lb-in

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

CENC4 50 CENC16 50 CENC35 50



NES 50 NES 50 NES 50

CA202 50 CA202 50 CA202 50

MT5 100 MT6 100 MT6 100

* 140A current carrying capacity of busbar should be takeninto account while connecting loads.

** Consult for other available colors.

E220514 E220514 E220514

Busbar System


High Temperature Ceramic EuroBlocks™

CB16CB4 CB6

W1

T T T

C2 W3

C3

D1

D2

W3

TT

HH

D1

D2

H

W2

H

W2

H

Dimensions mm

Note: All dimensions are shown in mm, to convert to inches please divide by 25.4.

Suitable for use in high tem-perature applications up to600°C (1112°F). Applicationsinclude hot melt glue guns,furnaces, heaters, processequipment and machinery.Terminal blocks are offeredwith mounting holes for panelmounting or free floatingapplications.

• Compact, space saving• Tubular screw clamp• Free float or panel mount• Temperature range:-40°C (-40°F) to600°C (1112°F)

• Standard color: white• MaterialHousing: SteatiteClamp: BrassScrews: Zinc plated steel

Ceramic

22-10 AWG 20-10 AWG

300V 300V

40 A 30 A

Cat. No. Std. Pk.

CB6/1 50

CB6/2H 50

CB6/3H 50

Insulation Material

Approvals

Wire Range

Voltage Rating

Current Rating

No. of Poles

1 (free floating)2 (free floating)2 (with mounting holes)3 (free floating)3 (with mounting holes)

Ceramic

20-6 AWG 18-6 AWG

300V 300V

76 A 65 A

Cat. No. Std. Pk.

CB16/2H 50

CB16/3H 50

Ceramic

24-12 AWG 24-12 AWG

300V 300V

30 A 20 A

Cat. No. Std. Pk.

CB4/1 50CB4/2 50CB4/2H 50CB4/3 50CB4/3H 50

W T H C D1 D2 Fixing StrippingScrew Length

CB4/1 1 POLE 23 11 18.5 * 6CB4/2 2 POLE 23 18 18.5 * 6CB4/2H 2 POLE 23 24 18.5 14.6 6 3.5 M3X16 6CB4/3 3 POLE 25 25 18.5 * 6CB4/3H 3 POLE 25.4 36 18.5 13 6 3.5 M3X16 6

CB6/1 1 POLE 25 12 19.5 * 6CB6/2H 2 POLE 25.5 26 19.5 12.6 6 M3X16 6CB6/3H 3 POLE 25.5 41 19.5 15 6 M3X16 6

CB16/2H 2 POLE 28 31 23.2 16.5 6 3.5 M3X20 8.5CB16/3H 3 POLE 27.5 48 23.2 17 6 3.5 M3X20 8.5

1 Pole 2 Pole 2 Pole withmounting hole

3 Pole 3 Pole withmounting hole

E220514 E220514 E220514


Marking Systems


Marking Systems

• Identifiers for connectors, wires, cables and equipment• Cable ties, shrink tubing, labels and signs of different

sizes and materials, as well as customer-specific items.• Size: 14.9”x7.5”x1.77”• Weight: 6.6 lbs.

SCRIBERVS 210Scriber VS210

TThe VS200 base unit is a stand-aloneplotting system with an integral keyboardand display screen. The marker fixture,plotter pen, and the memory cassettehave to be inserted in the base unit tomake it operational. The base unit comesin an aluminum carrying case andincludes the memory cassette and thepower supply. A manual is available inEnglish and Spanish.

The VS 200 can be used to produce labelsof all types, with its fixture changeable ina matter of seconds.

The Vario VS 200 makes labeling easy. Themenu-driven program guides you quicklyand easily through all the steps.

It can be used at any time and in anyplace. Easily transported in its specialcase, the battery-operated (battery packsold separately) VS 200 can be operatedprecisely where you need it. The spaciouscase provides enough room for the exten-sive accessories.

Plotter VP 500

The VP 500 base unit is an auxiliary plotterand has to be connected to a PC via a par-allel port or USB connection. It is a highspeed plotting device and enables plottingof different markers in one setting. Themarker fixture and the plotter pen have tobe inserted before commencing the plot-ting operation. The base unit is primarilycontrolled through a PC with the help ofVario Sign software. Manual available inEnglish and Spanish.

The special design of the VP 500 enables itto hold different markers from variousmanufacturers at the same time. It is alsopossible to write on relatively large mark-ers with a maximum height 14 mm.

Fixtures

Fixtures are required for alignment ofmarkers with respect to the plotter pen.Different marker fixtures can be mountedon the plotter bed of the VP 500 at thesame time thereby reducing set up times.Fixtures for different markers from variousmanufacturers like Altech, Allen Bradley,Connectwell, ContaClip, Entrelec,Weidmuller, Phoenix Contact, PTR,Wieland, Wago, Murrplastik, Partex, SESSterling, etc. are available. For more infor-mation on ordering fixtures please contactAltech.

BASE UNIT (includes power supply, memory cassette and carrying case) . . . . . . . . . . . . . . . . . . . . .34000000STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxxMEMORY CASSETTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500001BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500000

Ordering Information

CMPS 500 PLOTTER PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34130008

VP 500 BASE UNIT (includes cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000030STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001VARIO SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000020SERVICE KIT (includes 4 seal bonnets and 10 priming print cards) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000026FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx ** See page 85.

Fixtures &MemoryCassette

Battery Pack Plotter Pen,Ink Cartridge

Fixtures Plotter Pen,Ink Cartridge

Vario Sign

PLOTTERVP 500CMPS 500 PLOTTER PACKAGE

• Identifiers for connectors, wires, cablesand equipment

• Cable ties, shrink tubing, labels and signsof different sizes and materials, as well ascustomer-specific items.

• Size: 26”x18”x4.9”

• CMPS plotter• Size: 17”x18”x4.9”• Tag Sizes: MT2, MT3, MT4, MT5, MT6,

MT8, MT9, MT10, MT12, MT15, MT20, MT25• CMPS software with cable• 2 fixtures for tags MT5-MT15

(MT9 sold separately)• 1 fixture for tags MT2 and MT25• 2 disposable pens


Engraver VE500

The engraving unit was specificallydesigned to be used with the VP500 amdCMPS 500 plotters. Changing back andforth between the pen-plotter and theengraver is easy. The engraver is meantto engrave plastic signs on double sidedmaterial, pre-cut or blank sheets, for leg-end plates, push button inlays, etc. Theengraver is programmed by the VarioSignsoftware for ease of use and design flexi-bility.

Engraving Needles

These engraving needles are to be usedwith the VE500 engraver. They have a 15°angle and are available in 6 tip widths oras a complete set.

Vacuum Cleaner Bag

Replacement bags for the VE500engraver’s vacuum cleaner

ENGRAVERVE500

VE500 ENGRAVER UNIT (VP500 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000040


VACUUM CLEANER BAG

VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000


ENGRAVING NEEDLE

Product Width Order No.Engraving Needle 0.20mm 35010003Engraving Needle 0.30mm 35010002Engraving Needle 0.40mm 35010001Engraving Needle 0.50mm 35010000Engraving Needle 0.70mm 35010004Engraving Needle 1.00mm 35010005Engraving Set(0.20, 0.30, 0.40, 0.50, 0.70, 1.00mm) 35010006Engraving Needle(0.20 mm cutter stainless steel) 35012033



Marking Systems


Marking Systems Accessories

Plotter PensThese “tubular-nib” pens are suitable forVario Scriber VS 200, Vario Plotter VP 500 andall current labeling and identification systemswith HP penholders. They are available in sixtip widths identified by body color - 0.18 mm,0.25 mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00mm; ink cartridge not supplied with pen.Special variants for other systems are avail-able on request. Specially designed pre-filledfelt-tip pens are available in a set of 4 colors(black, blue, red and green) and 2 sizes - 0.3and 0.7 mm.

Ink CartridgesThese are easy to insert “tubular-nib” pencartridges containing special black ink suit-able for marking, identifying and labeling vari-ous plastics. It is fast drying, smudge-proof,fade resistant, and resistant to chemicalswhen used on suitable plastic materials.

Disposable PensThe disposable pens use the same special inkas used in the ink cartridges. They deliver thesame outstanding durability and print qualityas the standard plotter pens with the conven-ience of a disposable pen. These pre-filledpens allow for fast, efficient and cost effectiveprinting without refilling ink or cleaning. Theyare available in two tip widths, 0.25 mm and0.35 mm.

Hand PensThe hand pens use the same special ink, asused in cartridges, and delivers the same out-standing durability and print quality. They areused for additional identification and speciallabeling tasks and are available in four tipwidths of 0.25mm, 0.35mm, 0.50 mm, and 0.70mm. No ink included. Must order part35100006.

Cleaning UnitIt is an easy-to-use cleaning unit developedspecially for EK Pens. The cleaning unitenables the pens to be rinsed thoroughlywhile preventing skin contact with cleaningfluid or ink. The cleaning unit can be used forup to ten cleaning cycles. The necessary pre-cautions must be taken when disposing ofcleaning fluid, the cleaning unit can bereused.

Pen CleanerThis cleaning solution comes in easy to han-dle cartridges and is used in conjunction withthe cleaning unit. A standard pack consists oftwo pen cleaner cartridges. Cleaning can beperformed on standard refillable pens only.

AdapterThis adapter allows the user of Sharpie™Ultra Fine felt tip pens instead of standardplotter pens.

Product Color Width Order No.

EK Plotter Pen black 0.18 mm 35001018






EK Ink Cartridge

(5 pieces, Black, 1 ml. each) black 35100006

EK Disposable Plotter Pen black 0.25 mm 35003025

EK Disposable Plotter Pen black 0.35 mm 35003035

EK Disposable Plotter Pen-ED* black 0.18 mm 35003118



EK Disposable Plotter Pen-ED* red 0.18 mm 35003218



EK Disposable Plotter Pen-ED* green 0.18 mm 35003318



EK Disposable Plotter Pen-ED* blue 0.18 mm 35003418



EK Hand Pen black 0.25 mm 35002025




EK Cleaning Unit (empty) 35100009

EK Pen Cleaner (2 pieces, 2x10 ml.) 35100008

EK Cleaning Set 35100010

(includes cleaning unit and pen cleaner)

Adapter for an Utra Fine Sharpie™ 35000501

*Not for imprinting on polycarbonate material.

“tubular-nib” pens,6 sizes for black ink



DisposablePen

ReÞllablePens

Pen Stand

Refrigerate pens whennot in use for long

periods of time.

Recovery and Storage StandThis stand is designed to keep the plotter pen in anupright position, when not used with the markingsystem.

The upright position allows the plotter pen to recoverand to be properly stored. It is recommended tostore plotter pens that will be idle for a few hours in adry and cool location, preferably in the refrigerator.

The recovery and storage stand accommodates easystorage and handling.

Call Altech for your free recovery and storage stand.

Cat. No. 35000100

Plotter Pen Handling and CarePlotter Pen Handling and Care

1

2

Handling and care of the EK-Team plotter pens for the universal EK-Team marking system.For the state of the art universal marking system by EK-team, the manufacture is supplying a fast drying and etching ink that isrequired for marking plastic material within the control and automation industry. Due to these special properties of the ink, theseplotter pens require much more care than a regular marking pen. Therefore EK-Team designed some helpful tools to keep your EK-teamplotter pen in tip top shape.

Suction Ball

Pen CleaningCLEANING UNITIt is an easy-to-use cleaning unit developed specially for reÞllable pens. The cleaning unit enablesthe pens to be rinsed thoroughly while preventing skin contact with cleaning ßuid or ink. Thecleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be takenwhen disposing of cleaning ßuid, the cleaning unit can be reused.

PEN CLEANERThis cleaning solution comes in easy to handle cartridges and is used in conjunction with thecleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performedon standard reÞllable pens only.

Cleaning Set Cat. No. 35100010

3

The "suction ball" is a helpful tool to bring a slightly cloggeddisposable or reÞllable plotter pen back to life.

The suction can unclog a slightly clogged plotter pen from thevacuum created within the "ball".

This additional tool can be very helpful in addition to the alreadyavailable cleaning kit (Cat. No. 35100010) for the reÞllable plotterpens.

5 replacement tips are included with each suction ball.

Cat. No. 35100013

Description Part No.

AltechAltech MT 2n - MT 4n, MT 7.5, MT 20, MT 25 34902081Altech MT 5 - MT 15 34902001Altech Group marker G1, G2, G4 34902080

ABB / EntrelecABB Entrelec universal - RC/RCT quarter size 34902063ABB Entrelec RC 510A, 610A, 810A 34902114ABB Entrelec RC 510B, 610B, 810B” 34902102ABB Entrelec RB-RBP 5-12 34902086ABB Entrelec BA 5-50 34902100ABB Entrelec PIB 34902101ABB Entrelec RCCV 34902038ABB Entrelec BS / ILS / ILS-H 34902106Set of sticky pads ( 8 pcs) for RC/RCT 34910000

Allen Bradley /WoertzAllen Bradley UniversalW4 SERIES OLD ABWORTZ & S.S. 34902046Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal (M5X8) 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001

Conta ClipSB5, SB6 BSTR10.12 34902002SB8/10 34902003

PhoenixPhoenix Contact ZBM 34902039Phoenix Contact ZB 34902047Phoenix Contact ZBFM 34902049Phoenix Contact ZBF, ZBN 34900050Phoenix Contact BNZ 34902051Phoenix Contact BN-ZB 34902052Phoenix Contact SS-ZB 34902053Phoenix Contact LBHZ 34902054Phoenix Contact PAB 34902055Phoenix Contact GPE 34902071Phoenix Contact GPE 34902106

WagoWAGOWMB 4/4,2/5 34902041WAGOWSB 4 34902074WAGOWSB 5/5,2 34902075WAGOWSB mini 34902076WAGO Group marker carrier 34902078WAGO Marking Strip 34902087WAGO Marker tags 34902094WAGOWTB 34902096WAGOWCB 34902097WAGOWMB inline 34902098WAGO 210-345 34902106Set of sticky pads (12 pcs) forTop Job (Marking Strip) 34910002

Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001

WielandWieland Universal 34902043Wieland BZ/WKF 1,5 04.243.2053.0 34902047Wieland BZ/WKF 1,5/10 Z4.243.2053.0 34902049Wieland Steierform 6 x 15, 10 x 20 34902106

VE500 and CMPS 500 Engraving Fixtures

EK-TEAMUniversal engraving and plot support plate half size (A4) 34902106Universal engraving and plot support plate full size (A3) 34902107Universal engraving and plot support plate 30x100 ninefold 34902115Universal engraving and plot support plate 60x100 fourfold 34902116Universal engraving and plot support plate 90x100 threefold 34902117

CUSTOM FIXTURES AND OTHER MANUFACTURERES ARE AVAILABLEContact Altech for Pricing (not in Price Book)


Marking Systems VP500 and CMPS 500 Fixtures

To put the finishing touch on yourapplication, we offer an extensiveselection of useful accessories tobuild and install DIN Rail terminalblock assemblies and to facilitatefactory and field wiring.

Accessories include end stops, endplates and partitions. Also offeredare DIN Rails, ferrules, jumpersand more. From design to commis-sioning and operation, Altechaccessories help you do the jobbetter.

We’ve tried to make the selectionof accessories as easy as possible.The most common accessories arelisted together with their orderinginformation on each terminal blockpage in this catalog.

Terminal BlockAccessories



ACCESORIESAltech accessories add the finishing touches to your terminalblock assemblies. End Stops prevent terminal blocks or othercomponents and devices from moving laterally on the rail.

End Plates close off the last terminal in a series, a vital func-tion, since sectional terminal blocks are supplied with one sideopen. Isolation partitions provide visual separation of terminalgroups, as well as electrical isolation between terminals of dif-ferent potentials.

INTERCONNECTIONIn addition, Altech offers a wide choice of both Internal andExternal Jumpers to minimize wiring time and reduce installa-tion cost. Available in standard 2, 3, 4 and 10 pole configura-tions, or custom multipole jumpers. Our internal jumpers screwdirectly into terminal block busbars.

External jumpers are available in straight-comb styles. Theymay be used for terminal blocks without internal jumpering pro-visions or in combination with internal jumpers.

MOUNTINGDIN Mounting Rails are internationally standardized and avail-able in 35mm, 32mm and 15mm sizes, with or without perfora-tions. These also accommodate a wide variety of control com-ponents such as circuit breakers, timers, motor starters, relays,switches, etc. The 15mm rail with miniature blocks is usedwhen space is at a premium.

MARKINGTAGSMarking Tags make DIN Rail assemblies easier to wireand facilitate troubleshooting. Altech’s extensive termi-nal block marking system includes standard or customprinted push on tags in a variety of sizes for circuitidentification.

Terminal Block Accessories


AltechTERMINAL BLOCKACCESORIES Isolation Partition

Separator Plate

Internal Jumper

End Plate

End Stop

DIN 35 mmMounting Rail

DIN 35-15 mmMounting Rail

DIN 32 mmMounting Rail

Isolated Internal Jumper

Shorting Screw

Shorting Sleeve

Current Bar


End Stop

MarkingTag

External Jumper

Support Bracket

SampleTerminal Block Assemblyshowing all accessories

48mm(1.89in)

M6 18mm(.71in)

Ø7mm (.28in)

60mm (2.36in)

74mm (2.91in)74mm(2.98 in.)

52mm(2.05 in.)

M6

18mm(.71in.)

H

Slot 6x15mm(.24x.59 in.)

Ø6mm(.24 in.)

DIN35 DIN35

Type

PerforatedSteel

UnperforatedSteel

Cat. No. Length Std. Pk.

2511120 2m 202511120/1M 1m 40

2511110 2m 202511110/1M 1m 40

Type

PerforatedSteel

UnperforatedSteel


CA701-15/S-2M 2m 10CA701-15/S 1m 20

CA701-15-2M 2m 10CA701-15 1m 20

DIN Mounting RailsAltech DIN Rails comply with DIN50045, 50022 and 50035 Standards.DIN Rails have been acceptedthroughout the world, allowing thedesigner to mount a wide variety ofcontrol components, devices, termi-nal blocks, etc. on the same rail. Theuse of DIN Rails enhances designcapabilities, saves space and reduceslabor.

Standard rails are made of steel withzinc plating and chromate passivationand are available in various configu-rations.

DIN Rails are available in 35mm (7.5and 15mm deep), 32mm and 15mmwidths and are supplied in 1 m (3'3")and 2 m (6’6”) lengths. Upon requestthey can be cut to custom lengths andpunched with holes or perforations.

• 35mm, 32mm, 15mm• Perforated or unperforated• Rail material is steel with electrolyt-ic zinc plating

CA603 TSTWSupport BracketsSupport Brackets elevate DIN Railsaway from the panel to facilitatecomponent mounting and toincrease wiring access. Angled brack-ets tilt the rail by 35° to improve visi-bility. Straight brackets are availablein three heights for optimum posi-tioning of the rail.

Brackets mount with 2 screws to anypanel or flat surface and have tappedcenter holes for rail mounting.Bracket material is steel, zinc platedyellow chromated.

Height

1“2”3”

Cat. No. Std. Pk. CA603 25

Suitable for all mounting rails

Cat. No. Std. Pk.

CA703 25CA803 25CA903 25

Complete with rail mounting hardware:including one screw & one locknut

35 mm x7.5 mm deep

35 mm x15 mm deep


18 18



DIN32 DIN15

MH2.5

Type

PerforatedSteel

UnperforatedSteel


2511160 2m 102511160/1M 1m 20

2511150 2m 102511150/1M 1m 20

Type

PerforatedSteel


CA601/S 1m 50

35 mm x15 mm deep

15 mm x5.5 mm deep

18

Cat. No. Jumper for Std. Pk.

MH2.5 CTS2.5U-N 1

MH4

Cat. No. Jumper for Std. Pk.

MH4 CTS4U-N 1

Mounting HandleMounting handle is used for mounting10 terminal blocks on a DIN rail, thussaving consideral time. Speciallydesigned pins in the mounting handlegrips the terminal blocks when pressedagainst entry.



End StopsEnd Stops prevent terminalblocks and other DIN Rail mountcomponents and devices frommoving laterally on the rail.Theyare available in polyamide 6.6and metal configurations for35mm, 32mm, and 15mm DINrails. CA102 and CA202 are largeendstops for heavy duty appli-cations. CA103 is a screwlessendstop and snaps on to theDIN rail.

Spacer / SeparatorCASP is a DIN Rail mountablespacer generally used for circuitseparation.

DIN RailMounting FootCMTB-35 is used to assemblecomponents on a DIN rail.Comes with pre-punched holes.

• Support bracket for DIN railmounting parts

• Hole Qty x dia., 4x4.3mm,2x5.5mm

CA602CA702 CA802

Material:Polyamide 6.6

DimensionsH x L xW:20 x 28 x 8 mm

Cat. No. Std. Pk.

CA602 50

Suitable for:15 mmDIN Rails



Cat. No. Std. Pk.

CA702 50

Suitable for:32 and 35 mm

DIN Rails

CA102 CA202



Cat. No. Std. Pk.

CA102 50

Suitable for:32 and 35 mm

DIN Rails


DimensionsH x L xW:44.5 x 50 x 9.5 mm

Cat. No. Std. Pk.

CA202 50




Cat. No. Std. Pk.

CA802 50


Material:Steel

DimensionsH x L xW:25 x 22.5 x 11.5 mm

Cat. No. Std. Pk.

CA502 50


Material:Steel

DimensionsH x L xW:27 x 39.5 x 16 mm

Cat. No. Std. Pk.

CA302 50

Suitable for:35x7.5mmDIN Rails

Material:Polyamide


Cat. No. Std. Pk.

CA103 50


Material:Steel


Cat. No. Std. Pk.

CA402 50

Suitable for:35x15 mmDIN Rails



Cat. No. Std. Pk.

CDL4USP 50

Suitable for:All

DIN Rails


DimensionsH x L xW:

18 x 58 x 18 mm

Cat. No. Std. Pk.

CMTB-35 50

Suitable for:Mounting Foot for35 mm DIN rails



Cat. No. Std. Pk.

CASP 50

Suitable for:All

DIN Rails

CASP

CA502CA302 CA402CA103

CMTB-35 CDL4USP



Group IdentificationGMH6, GMH7 & GMH8

To be mounted directly on Din Rails (GMH6 & GMH7). Asticker / paper needs to be inserted in the slot which iscovered by a transparent plastic sheet.


Group Marker,shown imprinted andattached to CA 702.Blank and customprinting available.Cat. No. MTG1

END PLATESEnd PlatesEnd plates are used tocover the open side of sec-tional DIN Rail mount ter-minal blocks. They shouldbe used at the end of anassembly of identical termi-nal blocks or wheneverthere is a change in thephysical size of the terminalblock.

• Material: polyamide 6.6• Standard color: gray


Cat. No. Std. Dimensions Suitable for:Pk. (H x L xW)

EP2.5/4UN 50 32 x 39 x 1.5 CTS2.5UN/4UN/CTT2.5UK/T/J/EEP6/10U 50 31 x 42.5 x 1.5 CTS6U/CTS10UEP25U 50 40 x 48 x 2 CTS25UEP35 50 43 x 50 x 1.5 CTS35UEPCMC1-2 50 35.5 x 46.5 x 2.5 CMC1-2EPCMC2-2 50 40.5 x 65 x 2.5 CMC2-2EPCDL4U 50 43 x 55 x 2.4 CDL4U/CDL4U(I.S)/ CDL4U(E) SeriesEPODL4U 50 49 x 68 x 5.5 ODL4U/ODL4UA(Front Side)EP1ODL4U 50 24 x 68 x 3 ODL4U/ODL4UA(Back Side)EPCTL2.5U 50 55.5 x 84 x 1.5 CTL2.5U/2.5UL/2.5U(I.S)EPCTL2.5UH 50 55.5 x 61 x 1.5 CTL2.5UH/2.5UH(L)/2.5UH(I.S)D2EPCMT4 50 22.5 x 27 x 1.5 CMT4/CMT4S/CMT4SUEPCMB4 50 27 x 27 x 7 CMB4EPCSFL4U 50 28 x 55.5 x 1.6 CSFL4U/4U(L)/CSDL4UEPCSFL6U 50 42.5 x 36 x 1.5 CSFL6U/CSDL6UEPCAFL4U 25 32 x 72 x 1.5 CAFL4U/4UL/4UNEPDDFL4U 25 49 x 87.6 x 3 DDFL4U/4ULR/4U(E)/4U(E)LREPCDTTU 50 41 x 63 x 3 CDTTU/CDTTUSHEPCKT4U 50 30.5 x 46.5 x 2.5 CKT4UEPCGT4U 50 40.5 x 43 x1 CGT4UEPCTC4U 50 34.5 x 47 x 2.5 CTC4UEPCSTSN5U 50 31 x 50 x 1.5 CSTSN4U/N5U/N6U/B4U/B5UEPSTH4 50 39.5 x 46 x 1.5 STH4EPSTH4DT 50 37.5 x 86 x 1.5 STH4DT / STH4DTSHEPCSC2.5T 50 23 x 58 x 1.5 CSC2.5T/CSCG2.5TEPCSC4T 50 28 x 65 x 1.5 CSC4T/CSCG4TEPCSC6T 50 32 x 72 x 2 CSC6T/CSCG6TEPCSC10T 50 37.5 x 75 x 1.5 CSC10T/CSCG10TEPCSC16T 50 82 x 38 x 1.5 CSC16T/CSCG16TEPCSCP2.5T(L&R) 25 27.5 x 35 x 5 CSCP2.5T/CSCP2.5T2EPCSC2.5T1-2 50 27 x 74 x 1.5 CSC2.5T1-2EPCSC2.5T2-2 50 25 x 90 x 1.5 CSC2.5T2-2/CSC2.5T/4(E)D3EPCSC4T1-2 50 28.5 x 84.5 x 1.5 CSC4T1-2EPCSC4T2-2 50 28.5 x 105 x 1.5 CSC4T2-2EPCSC6T1-2 50 94 x 30 x 1.5 CSC6T1-2EPAS2.5 50 35 x 54 x 1.5 AS2.5, 2.5/3, 2.5/4, AGT2.5, 2.5/3, 2.5/4EPAS4 50 27.5 x 61 x 1.5 AS4, 4/3, 4/4, AGT4, 4/3, 4/4EPAS6 50 33.5 x 74 x 1.5 AS6, 6/3, AGT6, 6/3EPASF4 50 37 x 86 x 1.5 ASF4/ASF4LEPADL2.5 50 43.5 x 80 x 1.5 ADL2.5/ADL2.5(E)D1/D2



PARTITIONSIsolation PartitionsIsolation partitions provideseparation between termi-nal blocks with differentpotentials. When used forDC power applications,voltages of up to ± 600V DCcan be used on either sideof the isolation partition.They also provide visualseparation between groupsof blocks.

• Material: polyamide 6.6• Standard color: gray

Separator PlatesUsed for electrical separa-tion of adjacent jumpers.They can be inserted afterthe terminal blocks havebeen assembled on DINrail. There is no loss ofwidth.

Protective Cover /Side Holding Plates

For protection against dust andshock, transparent protectivecover can be installed abovethe terminal block assemblywith the aid of side/holdingplates. The side holding platescan be fitted on 35 mm and 32mm Din rails. These platesshould be backed by standardend stops.

SEPARATOR PLATES

CTSPC CSP1

150 mm

For all Rail MountingTerminals Mounting Accessoriesfor CTSPC

Assmebled Block installedwith Protective Cover


PP2.5/4UN 50 37 x 44 x 1.6 CTS2.5UN/4UN/CTT2.5UK/T/J/EPP6/10U 50 37.5 x 56.5 x 1.5 CTS6U/CTS10UPP25U 50 46.5 x 62 x 1.5 CTS25UPP25UN 50 42.5 x 62 x 1 CTS25UNPP35U 50 50 x 64.5 x 1.5 CTS35UPP35UN 50 50 x 64.5 x 1 CTS35UNPPCMT4 50 32.5 x 37 x 1.6 CMT4/CMT4S/CMT4SUPPCSFL4U 50 42.5 x 62 x 1.5 CSFL4U/4U(L)/CSDL4UPPCSC2.5T 50 28 x 58.7 x 1.5 CSC2.5T/CSCG2.5TPPCSC4T 50 33 x 65 x 1.5 CSC4T/CSCG4TPPCSC6T 50 36.5 x 72 x 2 CSC6T/CSCG6T


SP2.5/4UN 100 17.5 x 17.4 x 1.4 CTS2.5UN/4UN/CTT2.5UK/T/J/ESP6/10U 100 15.4 x 16.2 x 1.5 CTS6U/CTS10U/16USPCDL4U 100 15.4 x 16.2 x 1.6 CDL4U/CDL4U(I.S)/ CDL4U(E) SeriesSPCMB4 100 14.5 x 12 x 1.5 CMB4


INTERNAL JUMPER

1 Internal Jumpering System notavailable.

2 100 pole strip can be broken down toany number of poles desired.

Jumpering SystemThe jumpering systems bus poten-tials between terminal blocks, reduc-ing wiring time. Adjacent blocks orselective terminal blocks within anassembly can be easily interconnect-ed, leaving terminal clamps free forwiring. Purchase complete assem-blies, which are ready for installation,or select individual components tocreate custom or extra long jumpers.Jumper ampacity is lower than therated current of the respective termi-nal blocks, therefore, applied currentmust not exceed the maximum cur-rent value of the block. Internaljumpers may be used in combinationwith external jumpers to achieveadditional jumpering possibilities.

Internal Jumper AssembliesInternal Jumper Assemblies consist of aCurrent Bar, Shorting Sleeves andscrews.They install easily into the centerof the terminal block and connect to thecurrent bar. They are available as stan-dard 2, 3, 4 or 10 pole assemblies andare ready for immediate installation.Insulated internal jumpers provide shockprotection when installed on terminalblock assemblies.

External JumperExternal Jumpers bus potentialsbetween terminal blocks, reducingwiring time. Adjacent or selectedblocks within an assembly can beeasily interconnected. Jumper polesmay be removed for selectivejumpering. Jumpers are insulatedand available in 2, 3, 4 and 10 poleversions.They are made of tin platedbrass/copper.

Current BarsCurrent Bars are offered to createcustom jumper assemblies forincreased number of poles or customjumpers. Select the current bar withthe required number of poles, or fieldcut them to the required length.Theyare made of tin or nickel plated cop-per or brass.

Shorting Sleeves & ScrewsShorting Sleeves & Screws ensurereliable and mechanically safe elec-trical connections between currentbars and the terminal block currentbars. One shorting sleeve is requiredfor each jumpered terminal.They aremade of nickel plated brass.

Cat. No. Torque Std. Pk.

CA721/2 0.4 Nm 100CA721/3 100CA721/4 100CA721/10 10CA721/100 10

CA722/2 0.4 Nm 100CA722/3 100CA722/4 100CA722/10 10CA722/100 10

CA723/2 0.5 Nm 100CA723/3 50CA723/4 50CA723/10 10

CA724/2 0.5 Nm 100CA724/3 50CA724/4 50CA724/10 10

CA751/2 0.8 Nm 50CA751/3 50CA751/4 50CA751/10 10

CA725/2 0.8 Nm 50CA725/3 20CA725/4 20CA725/10 10

CA726/2 0.8 Nm 50CA726/3 20CA726/4 20CA726/10 10

CA771/2 0.8 NM 50CA771/3 20CA771/4 20CA771/10 10

CA727/2 0.4 Nm 100CA727/3 100CA727/4 100CA727/10 10

CA729/2 0.5 Nm 100CA729/3 50CA729/4 50CA729/10 10

CA722/2 0.4 Nm 100CA722/3 50CA722/4 50CA722/10 20CA722/100 20

INSULATED INTERNAL JUMPER


CA741/2 0.4 Nm 100CA741/3 100CA741/4 100CA741/10 10CA741/100 10

CA742/2 0.4 Nm 100CA742/3 100CA742/4 100CA742/10 10CA742/100 10

CA743/2 0.5 Nm 100CA743/3 50CA743/4 50CA743/10 10

CA744/2 0.5 Nm 100CA744/3 50CA744/4 50CA744/10 10

CA761/2 0.8 Nm 50CA761/3 50CA761/4 50CA761/10 10

CA745/2 0.8 Nm 50CA745/3 20CA745/4 20CA745/10 10

CA746/2 0.8 Nm 50CA746/3 20CA746/4 20CA746/10 10

CA781/2 0.8 NM 50CA781/3 20CA781/4 20CA781/10 10

CA747/2 0.4 Nm 100CA747/3 100CA747/4 100CA747/10 10

CA749/2 0.5 Nm 100CA749/3 50CA749/4 50CA749/10 10

Terminal Series Poles

CTS2.5UN 234101002

CTS4UN 2CMC1-2 3CMC2-2 4CTS4UTM 10CKT4U 1002

10 (breakable)

CTS6U 2CDTTU1 3CDTTU-SH1 4CSDL6U1 100CSFL6U1

CTS10U 23410

CTS16U 23410

CTS25U 23410

CTS35U 23410

CTS35UN* 23410

CMT4 2CMT4S 3CMB4 4CDL4U 10CDL4U(I.S) 1002

ODL4U 10 (breakable)CDL4UTM

DDFL4U 2DDFL4U(E) 3DDDL4U 4CSFL4U1 10CSFL4U(L)1CSDL4U

CAFL4U 2CAFL4U(L)1 3

410

CTL2.5U 2CTL2.5UH 3CTL2.5UL 4CTL2.5UHL 10CTL2.5U(I.S) 1002

10 (breakable)


Screw Clamp Terminal Block Accessories


EXTERNAL JUMPER


CA717/2 0.4 Nm 100CA717/3 100CA717/4 100CA717/10 20

CA713/2 0.5 Nm 100CA713/3 100CA713/4 100CA713/10 20

CA710/2 0.8 Nm 100CA710/3 50CA710/4 50CA710/10 20

CA718/2 0.8 Nm 100CA718/3 50CA718/4 50CA718/10 20

CA714/2 0.5 Nm 100CA714/3 100CA714/4 100CA714/10 20

CA711/2 0.8 Nm 100CA711/3 50CA711/4 50CA711/10 20

CA716/2 0.8 Nm 50CA716/3 50CA716/4 50CA716/10 20

CA715/2 0.4 Nm 100CA715/3 100CA715/4 100CA715/10 20

CURRENT BAR

Cat. No. Std. Pk.

CA703/01 100CA704/01 100CA705/01 100CA731/10 100CA731/100 10

CA703/1 100CA704/1 100CA705/1 100CA732/10 10CA732/100 100

CA703/2 100CA704/2 100CA705/2 100CA733/10 100

CA703/3 100CA704/3 100CA705/3 100CA734/10 100

CA703/8 100CA704/8 100CA705/8 100CA739/10 100

CA703/4 100CA704/4 100CA705/4 100CA735/10 100

CA703/5 100CA704/5 100CA705/5 100CA736/10 100

CA703/10 100CA704/10 100CA705/10 100CA770/10 100

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/100 10CA732/10-A 100

CA703/6 100CA704/6 100CA705/6 100CA737/10 100

CA703/1 100CA704/1 100CA705/1 100CA732/10 100CA732/100 10CA732/10-A 100

SHORTING SLEEVE & SCREWS


CA707/S/Q/01 0.4 Nm 100

CA707/S/Q/01 0.4 Nm 100

CA707/S/Q/1 0.5 Nm 100

CA707/S/Q/1 0.5 Nm 100

CA707/S/Q/5 0.8 Nm 100

CA707/S/Q/2 0.8 Nm 100

CA707/S/Q/2 0.8 Nm 100

CA707/S/Q/2 0.8 Nm 100

CA707/S/Q 0.4 Nm 100

CA707/S/Q/3 0.5 Nm 100

CA707/S/Q/01 0.4 Nm 100

Screw Clamp Terminal Block Accessories

Cat. No. Std. Pk.

CA801/1 100CA801/2 100CA801/3 100CA801/4 100CA801/1 100CA801/1 100CA801/2 100CA801/2 100CA801/3 100CA803/1 100CA803/1 100CA801/1 100CA801/7 100

Terminal

CSC2.5TCSC4TCSC6TCSC10TCSC2.5T1-2CSC2.5T2-2CSC4T1-2CSC4T2-2CSC6T1-2CSCP2.5TCSCP2.5T2ADL2.5ASF4

Cat. No. Std. Pk.

CA801/1-3 100CA801/2-3 100CA801/3-3 100

CA801/1-3 100CA801/1-3 100CA801/2-3 100CA801/2-3 100CA801/3-3 100

CA801/1-3 100

Cat. No. Std. Pk.

CA901/1 100CA901/2 100CA901/3 100

CA901/1 100CA901/1 100CA901/2 100CA901/2 100CA901/3 100

CA901/1 100

Wire Type Jumper For adjacent jumperingFor alternate jumpering

ADJACENT JUMPERALTERNATE JUMPER WIRETYPE JUMPER

Step DownJumpersUsed for jumperingdifferent size blocks.

Terminal

CSC6T –CSC4T

CSC6T –CSC2.5T

CSC4T –CSC2.5T

Cat. No. Std. Pk.

CA901/4 100

CA901/5 100

CA901/6 100


Spring Clamp Accessories



Cat. Std. Pk. DimsNo. Strips Tags H W

MT2 10 100 4.9 5.8

MT3 20 100 5.0 10.0

MT4 10 100 5.0 4.8

MT5 10 100 9.4 4.5

MT6 10 100 9.4 5.5

MT8 10 100 10.4 7.3

MT9 10 100 10.3 8.7

MT9F 10 10 10.3 90.0

MT10 20 100 10.4 9.4

MT12 20 100 10.4 11.3

MT15 20 100 10.4 14.3

MT20 20 100 4.9 20

MT25 20 100 4.9 25


MT2/V 10 100 4.9 5.8

MT3/V 20 100 5.0 10.0

MT4/V 10 100 5.0 4.8

MT5/V 10 100 9.4 4.5

MT6/V 10 100 9.4 5.5

MT8/V 10 100 10.4 7.3

MT9/V 10 100 10.3 8.7

MT9F/V 10 10 10.3 90.0

MT10/V 20 100 10.4 9.4

MT12/V 20 100 10.4 11.3

MT15/V 20 100 10.4 14.3

MT20/V 20 100 4.9 20

MT25/V 20 100 4.9 25


MT2/H 10 100 4.9 5.8

MT3/H 20 100 5.0 10.0

MT4/H 10 100 5.0 4.8

MT5/H 10 100 9.4 4.5

MT6/H 10 100 9.4 5.5

MT8/H 10 100 10.4 7.3

MT9/H 10 100 10.3 8.7

MT9F/H 10 10 10.3 90.0

MT10/H 20 100 10.4 9.4

MT12/H 20 100 10.4 11.3

MT15/H 20 100 10.4 14.3

MT20/H 20 100 4.9 20

MT25/H 20 100 4.9 25

Consecutive Digits(Specify decade)Nos. 1-10, 11-20, etc. up to 100 *Nos. 101-110, etc. up to 999 *

Consecutive Digits(Specify decade)Nos. 1-10, 11-20, etc. up to 100Nos. 101-110, etc. up to 999

Identical Characters(Specify digits, characters)Nos. 1, 2, 3 etc. up to 999 *Characters A, B.up to Z,

Symbols +, -, *

Group Marker,shown imprinted andattached to CA 702.Blank and customprinting available.Cat. No. MTG1

BLANK MARKINGTAGSMarking TagsThe cost effective MTmarking system providesquick and accurate identifi-cation. MT Push-OnMarking Tags fit all AltechDIN Rail mount and panelmount terminal blocks.They can be inserted indi-vidually or as strips of 10tags on terminal blockassemblies for quick andeasy marking.

MT Marking Tags are sup-plied blank for custommarking or they can beordered with a horizontalor vertical imprint. Thestandard tag color is whitewith black imprint. Tagscan be ordered with up to3 characters each. Imprintscan be either consecutiveor identical characters. MTtags, catalog numbersMT2-MT8 are supplied inpacks of identical strips, 10tags per strip. Catalognumbers MT10-MT15 aresupplied in packs of identi-cal strips, 5 tags per strip.

Group marker MTG1 isused for group identifica-tion and can be fixed onthe end stop CA702.

When ordering specifystrip marking as a suffix;i.e. MT2/H-1-10.

Warning Labels

These 5 position warninglabels can be mounted ontop of 8 mm TerminalBlocks. Besides givingvisual identification, it alsomakes an entire DIN RailTerminal Block assemblycompletely shock proof.SWL6 warning labels aresuitable for CTS6U,CMDB6 and CDB6 seriesTerminal Blocks.

VERTICAL MARKINGTAGSHORIZONTAL MARKINGTAGS


DimensionsH x L xW:

4 x 39.5 x 27 mm

Cat. No. Std. Pk.

SWL6 50

Suitable for: All DIN Rails

SWL6


Marking Systems


Marking Systems

• Identifiers for connectors, wires, cables and equipment• Cable ties, shrink tubing, labels and signs of different

sizes and materials, as well as customer-specific items.• Size: 14.9”x7.5”x1.77”• Weight: 6.6 lbs.

SCRIBERVS 210Scriber VS210

TThe VS200 base unit is a stand-aloneplotting system with an integral keyboardand display screen. The marker fixture,plotter pen, and the memory cassettehave to be inserted in the base unit tomake it operational. The base unit comesin an aluminum carrying case andincludes the memory cassette and thepower supply. A manual is available inEnglish and Spanish.

The VS 200 can be used to produce labelsof all types, with its fixture changeable ina matter of seconds.

The Vario VS 200 makes labeling easy. Themenu-driven program guides you quicklyand easily through all the steps.

It can be used at any time and in anyplace. Easily transported in its specialcase, the battery-operated (battery packsold separately) VS 200 can be operatedprecisely where you need it. The spaciouscase provides enough room for the exten-sive accessories.

Plotter VP 500

The VP 500 base unit is an auxiliary plotterand has to be connected to a PC via a par-allel port or USB connection. It is a highspeed plotting device and enables plottingof different markers in one setting. Themarker fixture and the plotter pen have tobe inserted before commencing the plot-ting operation. The base unit is primarilycontrolled through a PC with the help ofVario Sign software. Manual available inEnglish and Spanish.

The special design of the VP 500 enables itto hold different markers from variousmanufacturers at the same time. It is alsopossible to write on relatively large mark-ers with a maximum height 14 mm.

Fixtures

Fixtures are required for alignment ofmarkers with respect to the plotter pen.Different marker fixtures can be mountedon the plotter bed of the VP 500 at thesame time thereby reducing set up times.Fixtures for different markers from variousmanufacturers like Altech, Allen Bradley,Connectwell, ContaClip, Entrelec,Weidmuller, Phoenix Contact, PTR,Wieland, Wago, Murrplastik, Partex, SESSterling, etc. are available. For more infor-mation on ordering fixtures please contactAltech.

BASE UNIT (includes power supply, memory cassette and carrying case) . . . . . . . . . . . . . . . . . . . . .34000000STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxxMEMORY CASSETTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500001BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35500000


CMPS 500 PLOTTER PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34130008

VP 500 BASE UNIT (includes cable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000030STARTER KIT (includes cleaning unit, pen cleaners, felt pen, 0.25 mm plotter pen)and ink cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000001VARIO SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000020SERVICE KIT (includes 4 seal bonnets and 10 priming print cards) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000026FIXTURES (Contact Altech for available manufactures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3490xxxx ** See page 85.

Fixtures &MemoryCassette

Battery Pack Plotter Pen,Ink Cartridge

Fixtures Plotter Pen,Ink Cartridge

Vario Sign

PLOTTERVP 500CMPS 500 PLOTTER PACKAGE

• Identifiers for connectors, wires, cablesand equipment

• Cable ties, shrink tubing, labels and signsof different sizes and materials, as well ascustomer-specific items.

• Size: 26”x18”x4.9”

• CMPS plotter• Size: 17”x18”x4.9”• Tag Sizes: MT2, MT3, MT4, MT5, MT6,

MT8, MT9, MT10, MT12, MT15, MT20, MT25• CMPS software with cable• 2 fixtures for tags MT5-MT15

(MT9 sold separately)• 1 fixture for tags MT2 and MT25• 2 disposable pens


Engraver VE500

The engraving unit was specificallydesigned to be used with the VP500 amdCMPS 500 plotters. Changing back andforth between the pen-plotter and theengraver is easy. The engraver is meantto engrave plastic signs on double sidedmaterial, pre-cut or blank sheets, for leg-end plates, push button inlays, etc. Theengraver is programmed by the VarioSignsoftware for ease of use and design flexi-bility.

Engraving Needles

These engraving needles are to be usedwith the VE500 engraver. They have a 15°angle and are available in 6 tip widths oras a complete set.

Vacuum Cleaner Bag

Replacement bags for the VE500engraver’s vacuum cleaner

ENGRAVERVE500

VE500 ENGRAVER UNIT (VP500 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000040


VACUUM CLEANER BAG

VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000


ENGRAVING NEEDLE

Product Width Order No.Engraving Needle 0.20mm 35010003Engraving Needle 0.30mm 35010002Engraving Needle 0.40mm 35010001Engraving Needle 0.50mm 35010000Engraving Needle 0.70mm 35010004Engraving Needle 1.00mm 35010005Engraving Set(0.20, 0.30, 0.40, 0.50, 0.70, 1.00mm) 35010006Engraving Needle(0.20 mm cutter stainless steel) 35012033



Marking Systems



Plotter PensThese “tubular-nib” pens are suitable for VarioScriber VS 200, Vario Plotter VP 500 and all cur-rent labeling and identification systems withHP penholders. They are available in six tipwidths identified by body color - 0.18 mm, 0.25mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00 mm;ink cartridge not supplied with pen. Specialvariants for other systems are available onrequest. Specially designed pre-filled felt-tippens are available in a set of 4 colors (black,blue, red and green) and 2 sizes - 0.3 and 0.7mm.

Ink CartridgesThese are easy to insert “tubular-nib” pen car-tridges containing special black ink suitable formarking, identifying and labeling various plas-tics. It is fast drying, smudge-proof, fade resist-ant, and resistant to chemicals when used onsuitable plastic materials.

Disposable PensThe disposable pens use the same special inkas used in the ink cartridges. They deliver thesame outstanding durability and print quality asthe standard plotter pens with the convenienceof a disposable pen. These pre-filled pensallow for fast, efficient and cost effective print-ing without refilling ink or cleaning. They areavailable in two tip widths, 0.25 mm and 0.35mm.

Hand PensThe hand pens use the same special ink, asused in cartridges, and delivers the same out-standing durability and print quality. They areused for additional identification and speciallabeling tasks and are available in four tipwidths of 0.25mm, 0.35mm, 0.50 mm, and 0.70mm. No ink included. Must order part 35100006.

Cleaning UnitIt is an easy-to-use cleaning unit developedspecially for EK Pens. The cleaning unitenables the pens to be rinsed thoroughly whilepreventing skin contact with cleaning fluid orink. The cleaning unit can be used for up to tencleaning cycles. The necessary precautionsmust be taken when disposing of cleaning fluid,the cleaning unit can be reused.

Pen CleanerThis cleaning solution comes in easy to handlecartridges and is used in conjunction with thecleaning unit. A standard pack consists of twopen cleaner cartridges. Cleaning can be per-formed on standard refillable pens only.

AdapterThis adapter allows the user of Sharpie™ UltraFine felt tip pens instead of standard plotterpens.

Product Width Order No.

EK Plotter Pen 0.18 mm 35001018






EK Ink Cartridge

(5 pieces, Black, 1 ml. each) 35100006

EK Felt-tip Pen-Set (white tip) 0.30 mm 35000005

EK Felt-tip Pen-Set (yellow tip) 0.70 mm 35000010

EK Disposable Plotter Pen 0.25 mm 35003025

EK Disposable Plotter Pen 0.35 mm 35003035

EK Hand Pen 0.25 mm 35002025

EK Hand Pen 0.35 mm 35002035

EK Hand Pen 0.50 mm 35002050

EK Hand Pen 0.70 mm 35002070

EK Cleaning Unit (empty) 35100009

EK Pen Cleaner (2 pieces, 2x10 ml.) 35100008

EK Cleaning Set 35100010

(includes cleaning unit and pen cleaner)

Adapter for an Utra Fine Sharpie™ 35000501

“tubular-nib” pens,6 sizes for black ink

felt-tip pens,2 sizes, 4 colors



DisposablePen

ReÞllablePens

Pen Stand

Refrigerate pens whennot in use for long

periods of time.

Recovery and Storage StandThis stand is designed to keep the plotter pen in anupright position, when not used with the markingsystem.

The upright position allows the plotter pen to recoverand to be properly stored. It is recommended tostore plotter pens that will be idle for a few hours in adry and cool location, preferably in the refrigerator.

The recovery and storage stand accommodates easystorage and handling.

Call Altech for your free recovery and storage stand.

Cat. No. 35000100

Plotter Pen Handling and CarePlotter Pen Handling and Care

1

2

Handling and care of the EK-Team plotter pens for the universal EK-Team marking system.For the state of the art universal marking system by EK-team, the manufacture is supplying a fast drying and etching ink that isrequired for marking plastic material within the control and automation industry. Due to these special properties of the ink, theseplotter pens require much more care than a regular marking pen. Therefore EK-Team designed some helpful tools to keep your EK-teamplotter pen in tip top shape.

Suction Ball

Pen CleaningCLEANING UNITIt is an easy-to-use cleaning unit developed specially for reÞllable pens. The cleaning unit enablesthe pens to be rinsed thoroughly while preventing skin contact with cleaning ßuid or ink. Thecleaning unit can be used for up to ten cleaning cycles. The necessary precautions must be takenwhen disposing of cleaning ßuid, the cleaning unit can be reused.

PEN CLEANERThis cleaning solution comes in easy to handle cartridges and is used in conjunction with thecleaning unit. A standard pack consists of two pen cleaner cartridges. Cleaning can be performedon standard reÞllable pens only.

Cleaning Set Cat. No. 35100010

3

The "suction ball" is a helpful tool to bring a slightly cloggeddisposable or reÞllable plotter pen back to life.

The suction can unclog a slightly clogged plotter pen from thevacuum created within the "ball".

This additional tool can be very helpful in addition to the alreadyavailable cleaning kit (Cat. No. 35100010) for the reÞllable plotterpens.

5 replacement tips are included with each suction ball.

Cat. No. 35100013

Description Part No.

AltechAltech MT 2n - MT 4n, MT 7.5, MT 20, MT 25 34902081Altech MT 5 - MT 15 34902001Altech Group marker G1, G2, G4 34902080

ABB / EntrelecABB Entrelec universal - RC/RCT quarter size 34902063ABB Entrelec RC 510A, 610A, 810A 34902114ABB Entrelec RC 510B, 610B, 810B” 34902102ABB Entrelec RB-RBP 5-12 34902086ABB Entrelec BA 5-50 34902100ABB Entrelec PIB 34902101ABB Entrelec RCCV 34902038ABB Entrelec BS / ILS / ILS-H 34902106Set of sticky pads ( 8 pcs) for RC/RCT 34910000

Allen Bradley /WoertzAllen Bradley UniversalW4 SERIES OLD ABWORTZ & S.S. 34902046Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal (M5X8) 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001

Conta ClipSB5, SB6 BSTR10.12 34902002SB8/10 34902003

PhoenixPhoenix Contact ZBM 34902039Phoenix Contact ZB 34902047Phoenix Contact ZBFM 34902049Phoenix Contact ZBF, ZBN 34900050Phoenix Contact BNZ 34902051Phoenix Contact BN-ZB 34902052Phoenix Contact SS-ZB 34902053Phoenix Contact LBHZ 34902054Phoenix Contact PAB 34902055Phoenix Contact GPE 34902071Phoenix Contact GPE 34902106

WagoWAGOWMB 4/4,2/5 34902041WAGOWSB 4 34902074WAGOWSB 5/5,2 34902075WAGOWSB mini 34902076WAGO Group marker carrier 34902078WAGO Marking Strip 34902087WAGO Marker tags 34902094WAGOWTB 34902096WAGOWCB 34902097WAGOWMB inline 34902098WAGO 210-345 34902106Set of sticky pads (12 pcs) forTop Job (Marking Strip) 34910002

Weidmüller / Rockwell (Allen Bradley)Weidmüller MultiCard Universal 34902045Weidmüller MultiCard SF4-6 34902044Set of sticky pads (6 pcs) for Multicard Universal 34910001

WielandWieland Universal 34902043Wieland BZ/WKF 1,5 04.243.2053.0 34902047Wieland BZ/WKF 1,5/10 Z4.243.2053.0 34902049Wieland Steierform 6 x 15, 10 x 20 34902106

VE500 and CMPS 500 Engraving Fixtures

EK-TEAMUniversal engraving and plot support plate half size (A4) 34902106Universal engraving and plot support plate full size (A3) 34902107Universal engraving and plot support plate 30x100 ninefold 34902115Universal engraving and plot support plate 60x100 fourfold 34902116Universal engraving and plot support plate 90x100 threefold 34902117

CUSTOM FIXTURES AND OTHER MANUFACTURERES ARE AVAILABLEContact Altech for Pricing (not in Price Book)


Marking Systems VP500 and CMPS 500 Fixtures


Printed Circuit BoardWidth

TrackType High Guide (HG)

MTGTK1 73 ± 1mm (2.9 ± 0.05 in.)MTGTK2 110 ± 1mm (4.3 ± 0.05 in.)

MountingTrack Extrusion"Cut-to-Size" Formula

Extrusion Length = Printed CircuitBoard Length – 4.5mm (.175 in.)

Sizing Information

Narrow MountingTrackExtrusion and Components

Cat. No. Std. Pk.

MTGTK1/1M 5MTGTK1 5MTGTK1/1M/G 5MTGTK1/G 5

EPDR1 100EPDR1/G 100

MTGF1 100MTGF1/G 100

EPDP1 100EPDP1/G 100

EPS 200

MT2 100

1.100 1

MountingTrack1 meter, grey2 meter, grey1 meter, green*2 meter, green*

Accessories

DIN Rail Mount End Section, greyDIN Rail Mount End Section, green*

DIN Rail Mounting Foot, greyDIN Rail Mounting Foot, green*

Panel Mount End Section, greyPanel Mount End Section, green*

DIN Rail / Panel Mount End SectionScrews #4x1/2”, Phillips Pan head(2 required per end section)

MarkingTags

DIN Rail Mounting Kit(2x EPDR, 2x MTGF, 4x EPS)

MTGF1

EPDR1

EPS

MTGTK1

For PC BoardWidths 73mm (2.9 in.)

W

L

Mount standard or custom printed circuitboards in Mounting Tracks which can beconveniently DIN rail or panel mounted inyour control panel or cabinet. These are thesame tracks used for Altech interface mod-ules. We now make them available to you tohouse and protect your custom boards, etc.Tracks are easily cut to size or can beordered precut to specific lengths. They areeasily assembled from standard componentsand snap onto 35mm DIN rail or can be panelmounted.

Each track has two sets of printed circuitboard guides to accept two alternate boardwidths.

End Sections hold printed circuit boardssecurely in place and keep out foreignobjects.

MOUNTINGWhen mounting extrusions on DIN rail, ordertwo or more DIN Rail mounting feet. Thesefeet slide into grooves on the extrusion. Thenattach two DIN Rail Mount End Sectionswith help of EPS screws.

To panel mount, order two Panel Mount EndSections (and EPS screws), each with anintegral mounting flange with a 6 x 8mm (.24x .32 in.) hole slot.

If desired, tracks can be direct mountedusing double sided tape. Order two DIN railmount end sections (and EPS screws).

• Standard Lengths: 1m (3'-3") or 2m (6'-6")• Track Material: PVC• Temperature Limit:

Short Term - 80˚C (176˚F)Continuous - 70˚C (158˚F)

• End Section, Foot Material: Polyamide• Preassembled, Precut Lengths Available• Tracks Accept Standard MT2 Marking Tags

* Green color available on request.Contact Altech for more information.

PCB Mounting Tracks

PanelMount

DIN RailMount

PanelMount


aAlso applies for DIN Rail Mount Unit

Wide MountingTrackExtrusion and Components

Cat. No. Std. Pk.

MTGTK2/1M 5MTGTK2 5MTGTK2/1M/G 5MTGTK2/G 5

EPDR2 100EPDR2/G 100

MTGF2 100MTGF2/G 100

EPDP2 100EPDP2/G 100

EPS 200

MT2 100

For PC BoardWidths 110mm (4.9 in.)

W

LEPDP2

MTGTK2

PCB Mounting Tracks

DIN RailMount

73

69

16

84

2

3515

15

82

PCB MOUNTINGTRACK (73 mm)

DIN RAIL MOUNTING FOOT (73mm)

11.4

110

16

119

2

3515

15

117

PCB MOUNTINGTRACK (110 mm)

DIN RAIL MOUNTING FOOT (110mm)

11.4

Narrow Mounting Track

Wide Mounting Track

MTGF1

EPS

WALL MOUNT DIN RAIL MOUNTPANEL MOUNT

36.5 x 61.5 x 50

10 mm

Thermoplastic

3 screw clamps

125 V

15 A

Cat. No. Std. Pk.

PMRBU 1PMRGR 1PMRBA 1

SEALGASK 1

58.5 x 84 x 53.5

10 mm

Thermoplastic

3 screw clamps

125 V

15 A

Cat. No. Std. Pk.

DMRBU 1DMRGR 1DMRBA 1

SEALGASK 1

50 x 71 x 53.5

10 mm

Thermoplastic

3 screw clamps

125 V

15 A

Cat. No. Std. Pk.

WMRBU 1WMRGR 1WMRBA 1

SEALGASK 1

Features:

• DIN Rail, Panel Mount

orWall Mount

• Rating: 15A/125V AC

• Finger Protection: IP54

• Available in 3 colors.

External Dimension (HxWxL mm)

Stripping Length

Insulation Material

Type of Connection

Approvals*

Voltage Rating

Current Rating

Complete Kit:

BlueGrayBlack

Optional AccessorySealing Gasket


aAlso applies for DIN Rail Mount Unit

E154664 E154664 E154664

Receptacles


PANEL MOUNT

WALL MOUNT

DIN RAIL MOUNT

Wiring ofReceptacles1

1

1

1Optional Sealing Gasket for wet environments.

Receptacles


Altech’s Eurostrips are safe, econom-ical and meet worldwide standards.They are a cost-effective alternativeto barrier strips that require labor-intensive wire lugs and they reducethe number of electrical connectionsin circuits.

Eurostrips feature tubular screwclamps, wire protectors, and areready for immediate wire hookup.Eurostrips are ideal in small spaces,which means more room for othercomponents or reduced enclosuresize. Free float or mount them ontoany panel. They are available ineasy-to-cut 12-pole strips or pre-cut.

Feed-Through Eurostrips are suppliedwith wire protectors. Offered withflat bases or standoff feet, they aremolded of self-extinguishingpolyamide. Custom imprinting andmarking plates are available.

EUROSTRIPS®


EASY MOUNTING SAVESINSTALLATION TIMEEurostrips are mounted quickly in pan-els. Use standard screws or mountingpins, offered as accessories in this sec-tion, or leave them free floating to com-pletely eliminate mounting.

EASYCONNECTION SAVESMONEYWhat could be easier? Simply strip thewire insulation, insert the wire andtighten the screw to achieve a gas-tight,electrically efficient connection—everytime. Wire lugs are eliminated, savingmaterial cost and installation time.

EASY MODIFICATION REDUCESINVENTORYOffered in easy-to-cut 12-pole strips, theycan also be ordered precut with the requirednumber of poles. Polyamide housing canbe cut with a utility knife or hacksaw,providing flexibility to meet changingneeds. Because standard 12 pole stripscan be so easily cut to the required num-ber of poles, stocking is simplified andinventory is minimized.

RELIABLE CONNECTIONEVERY TIMEThe basis for the Eurostrip’s reliable con-nection is a precision machined tubularscrew clamp insert made from highlyconductive copper alloy which is nickelplated for maximum corrosion resist-ance. The clamping screw material is

high strength steel toprevent screw headbreakage or threaddamage. This providestrouble free opera-

tion. Screws areelectrogalva-

nized and bluechro-mated to provide cor-

rosion resistance. Optional nickel platedbrass screws may be ordered for highlycorrosive environments or marine appli-cations.

Standard Eurostrips feature stainlesssteel wire protectors. Unlike wire pro-tectors found in many competitive prod-ucts which use copper alloy materials,stainless steel has superior memorycharacteristics. Accordingly, the wireprotector will return to its original posi-tion even after repeated use. Thismeans trouble-free wire insertion andquicker reconnections.

HOUSINGSEurostrip housings are injection moldedfrom self-extinguishing polyamide 66/6,V-O molding material, possessing highdielectric strength and excellent electri-cal insulation and temperature resist-ance. Each housing has been speciallydesigned to provide creepage and clear-ance distances to achieve ratings up to600V. Choose low profile, flat basehousings for minimum clearance appli-cations (300V) or housings with mount-ing feet for maximum voltage isolation(600V).

ACCESSORIESExternal jumpers bus potentialsbetween poles on Eurostrips, eliminat-ing wire jumpers and reducing wiringtime. Isolation partition increases clear-ance between adjacent poles and pro-vides visual separation for more effi-cient wiring. Mounting pins simplifyinstallation and mounting of Eurostrips.Simply drill the mounting hole, positionand install the pin from underneath thepanel. When correct position isreached, pin will retain terminal topanel.

Identify circuits and reduce wiring mis-takes with marking plates. Order platesimprinted or blank. Position under or ontop of a Eurostrip housing.

Imprinting Eurostrips reduces wiringerrors and helps to identify circuits. UseImprinting to mark individual poleswhen high quantities are involved orcustom imprints are required.

Eurostrips®

FEED-THROUGH FLAT BASEPanel Mount

For wire-to-wire connections inHVAC, appliance, equipment,power distribution and otherindustrial applications withstrict budget and space require-ments. Easy to use double rowterminal strips are a cost-effec-tive alternative to barrier stripsor other types of terminalblocks. Simply strip the wire,insert and tighten the screw.Eurostrips feature tubular screwclamps, with wire protectors,and recessed metal parts for fin-ger protection. The stainlesssteel wire protectors exhibitexcellent memory and the mosteffective connection.

Eurostrips described on this andthe following page are availablewith a flat base for minimumclearance applications.They canbe panel mounted or left to freefloat. Offered in easy-to-cutstandard 12-pole strips, they canalso be ordered precut with therequired number of poles.

• Tubular screw clamp• Panel mount or free float• Housing material:

- Polyamide 66/6- V-O flammability

• Color: opaque white• Marking plates or factoryimprinted application

10 mm

3.6 mm

6 mm

2.5-4 mm2 24-10 AWG

400V 300 V

10 A 30 A

0.8 Nm 7.0 lb-in

Cat. No. Std. Pk.

HE4WPR/02 100HE4WPR/03 100HE4WPR/04 100HE4WPR/05 100HE4WPR/06 50HE4WPR/07 50HE4WPR/08 50HE4WPR/09 50HE4WPR/10 50HE4WPR/11 50HE4WPR/12 50

8 mm

3 mm

5 mm

1-2.5 mm2 24-12 AWG

400 V 300 V

6 A 20 A

0.5 Nm 4.4 lb-in

Cat. No. Std. Pk.


HE1 HE4

Pole Spacing

Mounting Hole Diameter

Stripping Length

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

No. of Poles

23456789101112

Flat base with wire protector Flat base with wire protector

Dimensions mm

A = 8.0 H = Ø2.8B = M2.6 I = 2.8C = 5.2 J = 6.5D = 2.8 K = 6.5E = Ø3 L = 94 (12 pole)F = Ø5 M = 12.2G = 8.0 N = 16.2

Dimensions mm

A = 10.0 H = Ø3.6B = M3 I = 3.2C = 6.4 J = 8.5D = 3.5 K = 7.9E = Ø3.6 L = 117 (12 pole)F = Ø5.7 M = 14.9G = 10.0 N = 20.0

E211022 E211022


Eurostrips®


12 mm

4.2 mm

7 mm

4-6 mm2 20-10 AWG

400V 300 V

16 A 40 A

0.8 Nm 7.0 lb-in

Cat. No. Std. Pk.


HE6

Flat base with wire protector

Dimensions mm

A = 12.0 H = Ø4.1B = M3.5 I = 4.0C = 7.7 J = 9.5D = 4.3 K = 8.9E = Ø4.2 L = 140 (12 pole)F = Ø6.3 M = 16.8G = 12.0 N = 22.6

15 mm

4.3 / 5.7 mm

8.5 mm

6-10 mm2 18-8 AWG

400V 300 V

25 A 50 A

1.2 Nm 10.6 lb-in

Cat. No. Std. Pk.


HE10


Dimensions mm

A = 15.0 H = Ø5.0B = M4 I = 4.8C = 9.3 J = 11.3D = 5.7 K = 11.6E = Ø4.3/5.7 L = 175 (12 pole)F = Ø8.2 M = 21.9G = 15.0 N = 25.1

15 mm

4.3 / 5.7 mm

8.5 mm

10-16 mm2 18-6 AWG

400 V 300 V

35-63 A 63 A

2.0 Nm 17.7 lb-in

Cat. No. Std. Pk.


HE16


Dimensions mm

A = 15.0 H = Ø5.6B = M5 I = 4.8C = 9.3 J = 11.3D = 5.7 K = 11.6E = Ø4.3/5.7 L = 175 (12 pole)F = Ø8.2 M = 21.9G = 15.0 N = 25.1

E211022 E211022 E211022

Eurostrips®

Dimensions mm

A = 8.0 I = 6.6B = M2.6 J = 6.5C = 5.2 K = 10.3D = 2.8 L = 94 (12 pole)E = Ø3 M = 16F = Ø5 N = 16.2G = 8.0 O = 10.1H = Ø2.8

Dimensions mm

A = 10.0 I = 6.7B = M3 J = 8.5C = 6.4 K = 12.1D = 3.5 L = 117 (12 pole)E = Ø3.6 M = 19.1F = Ø5.7 N = 20G = 10.0 O = 14.0H = Ø3.6

FEED-THROUGHSTANDOFF FEETPanel Mount

For wire-to-wire connections inHVAC, appliance, equipment,power distribution and otherindustrial applications withrestricted budget and spacerequirements.

Easy to use feed-through termi-nal strips are a cost-effectivealternative to barrier strips orother types of terminal blocks.Simply strip the wire, insert, andtighten the screw. Eurostripsfeature tubular screw clamps,with wire protectors, andrecessed metal parts for fingerprotection. The stainless steelwire protectors exhibit excellentmemory and the most effectiveconnection.

Eurostrips described on this andthe preceeding page are avail-able with standoff feet forincreased wiring efficiency.Theycan be panel mounted or left tofree float. Offered in easy-to-cut12-pole strips, they can also beordered precut with therequired number of poles.

• Tubular screw clamp• Panel mount or free float• Housing material:


• Color: opaque white• Marking plates orfactory imprinted

10 mm

3.6 mm

6 mm

2.5-4 mm2 24-10 AWG

400 V 600 V

10 A 30 A

0.8 Nm 7.0 lb-in

Cat. No. Std. Pk.

HE4HNWPR/02 100HE4HNWPR/03 100HE4HNWPR/04 100HE4HNWPR/05 100HE4HNWPR/06 50HE4HNWPR/07 50HE4HNWPR/08 50HE4HNWPR/09 50HE4HNWPR/10 50HE4HNWPR/11 50HE4HNWPR/12 50

HE1H HE4HN

Pole Spacing


Stripping Length

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

No. of Poles

23456789101112

Standoff feet with wire protector Standoff feet with wire protector

8 mm

3 mm

5 mm

1-2.5 mm2 24-12 AWG

400 V 600 V

6 A 20 A

0.5 Nm 4.4 lb-in

Cat. No. Std. Pk.

HE1HWPR/02 100HE1HWPR/03 100HE1HWPR/04 100HE1HWPR/05 100HE1HWPR/06 50HE1HWPR/07 50HE1HWPR/08 50HE1HWPR/09 50HE1HWPR/10 50HE1HWPR/11 50HE1HWPR/12 50

E211022 E211022


Eurostrips®

Dimensions mm

A = 12.0 I = 9B = M3.5 J = 9.6C = 7.7 K = 13.9D = 4.3 L = 140 (12 pole)E = Ø4.2 M = 21.8F = Ø6.3 N = 22.6G = 12.0 O = 15H = Ø4.1

Dimensions mm

A = 15.0 I = 10.7B = M5 J = 11.3C = 9.3 K = 17.5D = 5.7 L = 175 (12 pole)E = Ø4.3/5.7 M = 27.8F = Ø8.2 N = 25.1G = 15.0 O = 16H = Ø5.6

Dimensions mm

A = 15.0 I = 10.7B = M4 J = 11.3C = 9.3 K = 17.5D = 5.7 L = 175 (12 pole)E = Ø4.3/5.7 M = 27.8F = Ø8.2 N = 25.1G = 15.0 O = 16H = Ø5.0


15 mm

4.3/5.7 mm

8.5 mm

10-16 mm2 18-6 AWG

400 V 600 V

35-63 A 63 A

2.0 Nm 17.7 lb-in

Cat. No. Std. Pk.


12 mm

4.2 mm

7 mm

4-6 mm2 20-10 AWG

400 V 600 V

16 A 40 A

0.8 Nm 7.0 lb-in

Cat. No. Std. Pk.


HE6H HE10H

Standoff feet with wire protector Standoff feet with wire protector

15 mm

4.3/5.7 mm

8.5 mm

6-10 mm2 18-8 AWG

400 V 600 V

25 A 50 A

1.2 Nm 10.6 lb-in

Cat. No. Std. Pk.


HE16H

Standoff feet with wire protector

E211022 E211022 E211022

Eurostrips®

PLUGGABLEPanel Mount

For wire-to-wire connections inHVAC, appliance, equipment,power and other distributionapplications. Pluggable Euro-strips® speed and simplifyreplacement of subassemblies,etc. They reduce downtime andmisconnections.

Two-piece pluggable terminalstrips feature tubular screwclamps, with recessed metalparts for finger protection. Aspring loaded contact preventsinadvertant unplugging.

The headers and plugs are avail-able with flat base or standofffeet and can be panel mountedor free float. Offered in easy-tocut 12-pole strips, they can alsobe orderd precut with therequired number of poles.

• Tubular Screw Clamp• Panel Mount or Free Float• Housing material:


• Color: OpaqueWhite

10 mm

3.5 mm

3.6 mm

2.5-4mm2 24-10AWG

400V 300V

10A 20A

0.8Nm 7.2lb

Cat. No. Std. Pk.

HE42BU/02 100HE42BU/03 100HE42BU/04 100HE42BU/05 100HE42BU/06 50HE42BU/07 50HE42BU/08 50HE42BU/09 50HE42BU/10 50HE42BU/11 50HE42BU/12 50

HE42ST HE42BU

Pole Spacing


Stripping Length

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

No. of Poles

23456789101112

A

N LEø E D C

RM

IK

ø

P Q

J O G F

B

HDimensions mmA = 10.0 J = 15.2B = M3 K = 7.9C = 6.4 L = 117D = 3.6 M = 14.9E = Ø3.5 N = 34.4F = Ø5.7 O = 9.2G = 10.0 P = 20H = Ø3.5 Q = 14.4I = 3.2 R = 7

10 mm

3.5 mm

3.6 mm

2.5-4mm2 24-10AWG

400V 300V

10A 20A

0.8Nm 7.2lb

Cat. No. Std. Pk.

HE42ST/02 100HE42ST/03 100HE42ST/04 100HE42ST/05 100HE42ST/06 50HE42ST/07 50HE42ST/08 50HE42ST/09 50HE42ST/10 50HE42ST/11 50HE42ST/12 50

FLAT BASE

E211022 E211022


Eurostrips®


Dimensions mmA = 10.0 J = 15.2B = M3 K = 11.5C = 6.4 L = 117D = 3.6 M = 18.5E = Ø3.5 N = 34.4F = Ø5.7 O = 9.2G = 10.0 P = 20H = Ø3.5 Q = 14.4I = 6.8 R = 7

10 mm

3.5 mm

3.6 mm

2.5-4mm2 24-10AWG

400V 600V

10A 20A

0.8Nm 7.2lb

Cat. No. Std. Pk.

HE42SBU/02 100HE42SBU/03 100HE42SBU/04 100HE42SBU/05 100HE42SBU/06 50HE42SBU/07 50HE42SBU/08 50HE42SBU/09 50HE42SBU/10 50HE42SBU/11 50HE42SBU/12 50

HE42SST HE42SBU

10 mm

3.5 mm

3.6 mm

2.5-4mm2 24-10AWG

400V 600V

10A 20A

0.8Nm 7.2lb

Cat. No. Std. Pk.

HE42SST/02 100HE42SST/03 100HE42SST/04 100HE42SST/05 100HE42SST/06 50HE42SST/07 50HE42SST/08 50HE42SST/09 50HE42SST/10 50HE42SST/11 50HE42SST/12 50

STANDOFFFEET

E211022 E211022

A

N LEø E D C

RM

IK

ø

P Q

J O G F

B

H

Eurostrips®

Pole Spacing


Stripping Length

Approvals

Wire Range

Voltage Rating

Current Rating

Torque

Other Approvals

No. of Poles

23456789101112

Isolation Partition

Eurostrip

Thickness


KA46

HE4HN, HE6H

3.4 mm (.134 in.)

Cat. No. Std. Pk.

HEP4/6H 5

EXTERNAL JUMPERSAccessories

Convenient options that facilitateinstallation and wire termination.

External Jumpers

Bus potentials between poleson Eurostrip Terminal Stripsreducing wiring time and elim-inating wire jumpers.

Jumper Pole positions may beremoved to provide selectivejumpering. When using exter-nal jumpers, the terminal'srated cross section is usuallyreduced one wire size. Forjumper maximum current rat-ings, refer to the correspon-ding Eurostrip IEC/VDE currentrating.

• Material: copper alloy,nickel plated

• Insulation: polyamide 6.6• Color: black.

Isolation Partitions

Isolation Partition KA providesseparation between adjacentpoles of different potentials on600V Eurostrips with standofffeet. Visual separationbetween poles is also provid-ed by an isolation partition,assisting circuit identificationand increasing wiring efficien-cy

• Material: polyamide 6.6• Color: black

ISOLATION PARTITION

External Jumper

Eurostrip

Pole Spacing


HCL8 HCL10 HCL12 HCL15

HE1 HE4 HE6 HE10, HE16

8mm (.315) 10 mm (.394 in.) 12 mm (.472) 15 mm (.591 in.)

Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk. Cat. No. Std. Pk.

HCL8-2 100 HCL10-2 100 HCL12-2 100 HCL15-2 100HCL8-3 100 HCL10-3 100 HCL12-3 100 HCL15-3 100HCL8-4 100 HCL10-4 100 HCL12-4 100 HCL15-4 100HCL8-12 25 HCL10-12 25 HCL12-12 25 HCL15-12 25



Eurostrips®


H IL

W

Ø

Accessories

Convenient options that facilitateinstallation and wire termination.

Mounting Pins

Speed panel mounting ofEurostrips with MountingPins. Simply match drill clear-ance hole in panel, positionEurostrip and install MountingPin through hole and intomounting hole in Eurostriphousing. Once pin passesbeyond Eurostrip housing, itautomatically expands, secur-ing housing to panel. Use twoor more mounting pins perEurostrip.

• Material: polycarbonate• Color: gray.

Marking Plates

Install Marking Plate MPunder or on top of Eurostriphousing to identify individualpole positions to increasewiring efficiency, save instal-lation time and facilitate wirehook-up, system modificationand trouble shooting. Selectblank marking plate for handmarking or imprinted.

• Material: self-extinguishingPVC

• Color: white with blackimprint.

Imprinting

Mark individual pole positionsto save installation time andfacilitate wire hook-up, sys-tem modification and troubleshooting. Choose turret mark-ing for optimum identifica-tion.To order imprinting spec-ify consecutive, identical orcustom character imprints.

• Imprints: rub-resistant,black ink.

• Set up fee applies

• 1000 piece minimum

Mounting Pins

Eurostrip

Panel Thickness


H4 H6

HE4HN HE6H

0.5-1.5 mm 0.8-1.8 mm

Cat. No. Std. Pk. Cat. No. Std. Pk.

H4 50 H6 50

MARKING PLATES

Eurostrip HE4, HE4HN HE6, HE6H HE10, HE10H, HE16, HE16H

Ordering Information Cat.No. Desc. Std. Pk Cat.No. Desc. Std. Pk. Cat.No. Desc. Std. Pk.

BS24E Blank 25 BS60E Blank 25 BS1016E Blank 25BS24EM1-12 No. 1-12 25 BS60EM1-12 No. 1-12 25 BS1016EM1-12 No. 1-12 25BS24EM13-24 No. 13-24 25 BS60EM13-24 No. 13-24 25 BS1016EM13-24 No. 13-24 25

IMPRINTING

Imprint

MarkingInstruction

Ordering Example

Turret Location

Consecutive, imprint 1 through 12,Turret Location

Cat. No. Std. Pk.

HE4WPR/12i1-12 1000

Turret Location

Dimensions mm (in.)Mounting Pin Insertion Panel WidthPin Type Height (H) Length (IL) Hole Dia. (W)H4 21 12.6 4.2 8.5H6 24 14.7 5.2 11

Eurostrips®

MOUNTING PINS


InsulatedIndustry Standard

Ferrules insure reliable elec-trical connections when ter-minating stranded flexiblewire in terminal blocks, cir-cuit breakers or other con-trol devices. Insulated fer-rules prevent conductorbreakage due to bending,wire stress or vibrationwhile facilitating wire inser-tion into the terminal clamp.

Altech’s standard insulatedferrules are color coded byconductor size for conven-ient identification.

To ensure efficient ferrulecrimping, always select thesmallest ferrule diameterthat fits the wire and useonly professional crimpingtools. (Please refer to theordering pages and theCrimper Selector Guide onpage 98.)

• Sleeve: polypropylene• Tube: tin-plated copper

AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.

(mm2) Color Type No. mm (in.) A B C D Pk.*

24 (.25) Lt. Blue H0.25/6 2620.0 6.0(.24) 10.0 (.39) 6.0 (.24) 1.2 (.05) 2.3 (.09) 500/100

24 (.25) Lt. Blue H0.25/8 2621.0 8.0(.31) 12.0 (.47) 8.0 (.31) 1.2 (.05) 2.3 (.09) 500/100

22 (.34) Turquoise H0.34/6 2622.0 6.0(.24) 10.0 (.39) 6.0 (.24) 1.2 (.05) 2.5 (.10) 500/100

22 (.34) Turquoise H0.34/8 2623.0 8.0(.31) 12.0 (.47) 8.0 (.31) 1.2 (.05) 2.5 (.10) 500/100

20 (.50) Orange H0.50/6 2397.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.3 (.05) 2.8 (.11) 500/100

20 (.50) Orange H0.50/8 2201.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.3 (.05) 2.8 (.11) 500/100

18 (.75) White H0.75/6 2398.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.5 (.06) 3.3 (.13) 500/100

18 (.75) White H0.75/8 2202.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.5 (.06) 3.3 (.13) 500/100

18 (1.00) Yellow H1.00/6 2399.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.7 (.07) 3.5 (.14) 500/100

18 (1.00) Yellow H1.00/8 2203.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.7 (.07) 3.5 (.14) 500/100

16 (1.50) Red H1.50/8 2204.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.0 (.08) 4.0 (.16) 500/100

16 (1.50) Red H1.50/10 2400.0 10.0(.39) 16.0 (.63) 10.0 (.39) 2.0 (.08) 4.0 (.16) 500/100

16 (1.50) Red H1.50/18 2205.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.0 (.08) 4.0 (.16) 500/100

14 (2.50) Blue H2.50/8 2206.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.5 (.10) 4.7 (.19) 500/100

14 (2.50) Blue H2.50/12 2401.0 12.0(.47) 18.0 (.71) 12.0 (.47) 2.5 (.10) 4.7 (.19) 500/100

14 (2.50) Blue H2.50/18 2207.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.5 (.10) 4.7 (.19) 500/100

12 (4.00) Gray H4.00/10 2208.0 10.0(.39) 17.0 (.67) 10.0 (.39) 3.2 (.13) 5.4 (.21) 500/100

12 (4.00) Gray H4.00/12 2402.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.2 (.13) 5.4 (.21) 500/100

12 (4.00) Gray H4.00/18 2209.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.2 (.13) 5.4 (.21) 100

10 (6.00) Black H6.00/12 2210.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.9 (.15) 6.9 (.27) 100

10 (6.00) Black H6.00/18 2211.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.9 (.15) 6.9 (.27) 100

8 (10.00) Ivory H10.0/12 2212.0 12.0(.47) 22.0 (.87) 12.0 (.47) 4.9 (.19) 8.4 (.33) 100

8 (10.00) Ivory H10.0/18 2213.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 4.9 (.19) 8.4 (.33) 100

6 (16.00) Green H16.0/12 2214.0 12.0(.47) 24.0 (.94) 12.0 (.47) 6.2 (.24) 9.6 (.38) 100

6 (16.00) Green H16.0/18 2215.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 6.2 (.24) 9.6 (.38) 100

4 (25.00) Brown H25.0/18 2267.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 7.7 (.30) 12.0(.47) 50

4 (25.00) Brown H25.0/22 2272.0 22.0(.87) 36.0 (1.42) 22.0 (.87) 7.7 (.30) 12.0(.47) 50

2 (35.00) Beige H35.0/18 2276.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 8.7 (.34) 13.5(.53) 50

2 (35.00) Beige H35.0/25 2390.0 25.0(.98) 39.0 (1.54) 25.0 (.98) 8.7 (.34) 13.5(.53) 50

1 (50.00) Olive H50.0/20 2500.0 20.0(.79) 36.0 (1.42) 20.0 (.79) 10.9(.43) 16.0(.63) 50

2/0 (70.00) Yellow H70.0/21 2786.0 20.0(.79) 37.0 (1.46) 20.0 (.79) 13.4(.53) 17.0(.67) 25

3/0 (95.00) Red H95.0/25 2787.0 25.0(.98) 44.0 (1.73) 25.0 (.98) 15.4(.61) 19.0(.75) 25

4/0 (120.00) Blue H120.0/27 2788.0 27.0(1.06) 48.0 (1.89) 27.0 (1.06) 17.6(.69) 22.4(.88) 25

250MCM(150.0)Yellow H150.0/27 2789.0 32.0(1.26) 58.0 (2.28) 32.0 (1.26) 20.5(.81) 25.0(.98) 25

INDUSTRY STANDARD FERRULES

* Different standard packs are available as shown. To order the desired standard pack, please use the quantity required as a suffix to the cat. no.Example for 100 standard pack: Type H0.25/6, Cat. No. 2620.0/100

CRIMPER SELECTORGUIDESee page 109.

Ferrules

CSA Std C22.2 No. 65-93 - Wire ConnectorsCSA Std C22.2 No. 188-M1983 - Splicing Wire and Cable ConnectorsANSI/UL Std No. 486A - Wire Connectors and Soldering Lugs for Use with Copper ConductorsANSI/UL Std No. 486C - Splicing Wire Connectors220672

Tested According To:

InsulatedDIN Standard

Ferrules insure reliableelectrical connectionswhen terminating strand-ed flexible wire in termi-nal blocks, circuit breakersor other control devices.

Insulated ferrules preventconductor breakage dueto bending, wire stress orvibration while facilitatingwire insertion into the ter-minal clamp.

Altech’s DIN standard fer-rules are in compliancewith DIN requirements,making them ideal forexport applications. Theyalso have a specified colorcode convention that dif-fers from the color codeused for Altech’s industrystandard ferrules.

To ensure efficient ferrulecrimping, always selectthe smallest ferrule diam-eter that fits the wire anduse only professionalcrimping tools. (Pleaserefer to the orderingpages and the CrimperSelector Guide on page98.)

• Sleeve: polypropylene• Tube: tin plated copper

AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.

(mm2) Color Type No. mm (in.) A B C D Pk.*

20 (.50) White H0.50/6 2863.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.3 (.05) 2.8 (.11) 500/100

20 (.50) White H0.50/8 2864.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.3 (.05) 2.8 (.11) 500/100

20 (.50) White H0.50/10 2865.0 10.0(.39) 16.0 (.63) 10.0 (.39) 1.3 (.05) 2.8 (.11) 500/100

18 (.75) Gray H0.75/6 2866.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.5 (.06) 3.3 (.13) 500/100

18 (.75) Gray H0.75/8 2867.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.5 (.06) 3.3 (.13) 500/100

18 (.75) Gray H0.75/10 2868.0 10.0(.39) 16.0 (.63) 10.0 (.39) 1.5 (.06) 3.3 (.13) 500/100

18 (.75) Gray H0.75/12 2869.0 12.0(.47) 18.0 (.71) 12.0 (.47) 1.5 (.06) 3.3 (.13) 500/100

18 (1.00) Red H1.00/6 2870.0 6.0(.24) 12.0 (.47) 6.0 (.24) 1.7 (.07) 3.5 (.14) 500/100

18 (1.00) Red H1.00/8 2871.0 8.0(.31) 14.0 (.55) 8.0 (.31) 1.7 (.07) 3.5 (.14) 500/100

18 (1.00) Red H1.00/10 2872.0 10.0(.39) 16.0 (.63) 10.0 (.39) 1.7 (.07) 3.5 (.14) 500/100

18 (1.00) Red H1.00/12 2840.0 12.0(.47) 18.0 (.71) 12.0 (.47) 1.7 (.07) 3.5 (.14) 500/100

16 (1.50) Black H1.50/8 2841.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.0 (.08) 4.0 (.16) 500/100

16 (1.50) Black H1.50/10 2842.0 10.0(.39) 16.0 (.63) 10.0 (.39) 2.0 (.08) 4.0 (.16) 500/100

16 (1.50) Black H1.50/12 2843.0 12.0(.47) 18.0 (.71) 12.0 (.47) 2.0 (.08) 4.0 (.16) 500/100

16 (1.50) Black H1.50/18 2844.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.0 (.08) 4.0 (.16) 500/100

14 (2.50) Blue H2.50/8 2845.0 8.0(.31) 14.0 (.55) 8.0 (.31) 2.5 (.10) 4.7 (.19) 500/100

14 (2.50) Blue H2.50/12 2846.0 12.0(.47) 18.0 (.71) 12.0 (.47) 2.5 (.10) 4.7 (.19) 500/100

14 (2.50) Blue H2.50/18 2847.0 18.0(.71) 24.0 (.94) 18.0 (.71) 2.5 (.10) 4.7 (.19) 500/100

12 (4.00) Gray H4.00/10 2848.0 10.0(.39) 17.0 (.71) 10.0 (.39) 3.2 (.13) 5.4 (.21) 500/100

12 (4.00) Gray H4.00/12 2849.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.2 (.13) 5.4 (.21) 500/100

12 (4.00) Gray H4.00/18 2850.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.2 (.13) 5.4 (.21) 100

10 (6.00) Yellow H6.00/12 2851.0 12.0(.47) 20.0 (.79) 12.0 (.47) 3.9 (.16) 6.9 (.27) 100

10 (6.00) Yellow H6.00/18 2852.0 18.0(.71) 26.0 (1.02) 18.0 (.71) 3.9 (.16) 6.9 (.27) 100

8 (10.00) Red H10.00/12 2853.0 12.0(.47) 22.0 (.87) 12.0 (.47) 4.9 (.20) 8.4 (.33) 100

8 (10.00) Red H10.00/18 2854.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 4.9 (.20) 8.4 (.33) 100

6 (16.00) Blue H16.00/12 2855.0 12.0(.47) 24.0 (.87) 12.0 (.47) 6.2 (.24) 9.6 (.38) 100

6 (16.00) Blue H16.00/18 2856.0 18.0(.71) 28.0 (1.10) 18.0 (.71) 6.2 (.24) 9.6 (.38) 100

4 (25.00) Yellow H25.00/18 2857.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 7.7 (.30) 12.0(.47) 50

4 (25.00) Yellow H25.00/22 2858.0 22.0(.87) 36.0 (1.5) 22.0 (.87) 7.7 (.30) 12.0(.47) 50

2 (35.00) Red H35.00/18 2859.0 18.0(.71) 30.0 (1.18) 18.0 (.71) 8.7 (.34) 13.5(.53) 50

2(35.00) Red H35.00/25 2860.0 25.0(.98) 39.0 (1.54) 25.0 (.98) 8.7 (.34) 13.5(.53) 50

1 (50.00) Blue H50.00/20 2861.0 20.0(.79) 36.0 (1.5) 20.0 (.79) 10.9(.43) 16.0(.63) 50

DIN STANDARD FERRULES




Ferrules




UninsulatedFerrules insure reliable elec-trical connections when ter-minating stranded flexiblewire in terminal blocks, cir-cuit breakers or other con-trol devices.

Uninsulated ferrules pre-vent wire strands from fray-ing and breaking and areextremely cost effective.Their shorter lengths anduninsulated bodies offeradvantages when makingterminations in printed cir-cuit board terminal blocksand in other terminal blockswith smaller clamps or nar-row widths.

To ensure efficient ferrulecrimping, always select thesmallest ferrule diameterthat fits the wire and useonly professional crimpingtools. (Please refer to theordering pages and theCrimper Selector Guide onpage 109.)

• Tube: tin plated copper

AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.(mm2) Type No. mm (in.) A B C Pk.*

20 (.50) H0.50/6 2216.0 6.0 (.24) 6.0 (.24) 1.3 (.05) 2.1 (.08) 1000/100

18 (.75) H0.75/6 2217.0 6.0 (.24) 6.0 (.24) 1.5 (.06) 2.3 (.09) 1000/100

18 (.75) H0.75/10 2218.0 10.0 (.39) 10.0 (.39) 1.5 (.06) 2.3 (.09) 1000/100

18 (1.00) H1.00/6 2219.0 6.0 (.24) 6.0 (.24) 1.7 (.07) 2.5 (.10) 1000/100

18 (1.00) H1.00/10 2220.0 10.0(.39) 10.0 (.39) 1.7 (.07) 2.5 (.10) 1000/100

16 (1.50) H1.50/7 2221.0 7.0 (.28) 7.0 (.28) 2.3 (.09) 2.8 (.11) 1000/100

16 (1.50) H1.50/10 2222.0 10.0 (.39) 10.0 (.39) 2.3 (.09) 2.8 (.11) 1000/100

14 (2.50) H2.50/7 2223.0 7.0 (.28) 7.0 (.28) 2.5 (.10) 3.4 (.13) 1000/100

14 (2.50) H2.50/12 2224.0 12.0 (.47) 12.0 (.47) 2.5 (.10) 3.4 (.13) 1000/100

12 (4.00) H4.00/9 2225.0 9.0 (.35) 9.0 (.35) 3.2 (.13) 4.0 (.16) 1000/100

12 (4.00) H4.00/12 2226.0 12.0 (.47) 12.0 (.47) 3.2 (.13) 4.0 (.16) 1000/100

10 (6.00) H6.00/12 2227.0 12.0 (.47) 12.0 (.47) 3.9 (.15) 4.7 (.19) 500/100

10 (6.00) H6.00/15 2388.0 15.0 (.59) 15.0 (.59) 3.9 (.15) 4.7 (.19) 500/100

8 (10.00) H10.00/12 2228.0 12.0 (.47) 12.0 (.47) 4.9 (.19) 5.8 (.23) 500/100

8 (10.00) H10.00/15 2389.0 15.0 (.59) 15.0 (.59) 4.9 (.19) 5.8 (.23) 500/100

8 (10.00) H10.00/18 2229.0 18.0 (.71) 18.0 (.71) 4.9 (.19) 5.8 (.23) 500/100

6 (16.00) H16.00/12 2391.0 12.0 (.47) 12.0 (.47) 6.2 (.24) 7.5 (.30) 500/100

6 (16.00) H16.00/15 2392.0 15.0 (.59) 15.0 (.59) 6.2 (.24) 7.5 (.30) 500/100

6 (16.00) H16.00/18 2393.0 18.0 (.71) 18.0 (.71) 6.2 (.24) 7.5 (.30) 100

4 (25.00) H25.00/15 2394.0 15.0 (.59) 15.0 (.59) 7.7 (.30) 9.5 (.37) 500/100

4 (25.00) H25.00/18 2395.0 18.0 (.71) 18.0 (.71) 7.7 (.30) 9.5 (.37) 100

2 (35.00) H35.00/18 2396.0 18.0 (.71) 18.0 (.71) 8.7 (.34) 11.0 (.43) 100

1 (50.00) H50.00/32 2816.0 32.0 (1.26) 32.0 (1.26) 10.9 (.43) 13.0 (.51) 100

2/0 (70.00) H70.00/25 2790.0 25.0 (0.98) 25.0 (.98) 13.3 (.52) 15.0 (.59) 100

3/0 (95.00) H95.00/32 2791.0 32.0 (1.26) 32.0 (1.26) 15.3 (.60) 17.0 (.67) 50

4/0 (120.00) H120.00/32 2792.0 32.0 (1.26) 32.0 (1.26) 17.5 (.69) 19.0 (.75) 25

250MCM(150.00) H150.00/32 2793.0 32.0 (1.26) 32.0 (1.26) 19.5 (.77) 21.0 (.83) 25

350MCM(185.00) H185.00/32 2815.0 32.0 (1.26) 32.0 (1.26) 21.2 (.83) 23.5 (.93) 25

UNINSULATED FERRULES



Ferrules



AB1-S

AB2-S

Dual WireInsulatedDual Wire Ferrules havelarger diameters and spe-cial shaped sleeves thataccept two conductors ofthe same or different size.They provide an efficientconnection of multiplewires in the same terminalclamp or simplify wirejumpering between termi-nal clamps. They are colorcoded with the same con-vention as the insulatedDIN standard ferrules.

To ensure efficient ferrulecrimping always select thesmallest ferrule diameterthat fits the wire and useonly professional crimpingtools. (Please refer to theordering pages and theCrimper Selector Guide onpage 109.)

• Sleeve: polypropylene• Tube: tin plated copper

INSULATED FERRULESAssortment BoxHandy Assortment Boxes forconvenient dispensing andstorage of Industry and DINStandard Insulated Ferrules.Types AB1-S and AB1-D areequipped with five differentferrule sizes. Types AB2-Sand AB2-D are equipped withfour different ferrule sizes.Contents of each box is list-ed. Dimensions for industryand DIN standard insulatedferrules are listed on pages106.

DUAL WIRE FERRULES

Wires x AWG Cat. Stripping Length Ferrule Dimensions mm (in.) Std.(mm2) Color Type No. mm (in.) A B C D1 D2 Pk.*

2x20 (2x.50) White H2x0.50/8 2794.0 11.0 (.43) 14.6 (.57) 8.2 (.32) 1.7 (.07) 3.0 (.12) 5.0 (.20) 500/100

2x18 (2x.75) Gray H2x0.75/8 2775.0 11.0 (.43) 14.6 (.57) 8.2 (.32) 2.0 (.08) 3.0 (.12) 5.5 (.22) 500/100

2x18 (2x.75) Gray H2x0.75/10 2795.0 13.0 (.51) 16.4 (.65) 10.0 (.39) 2.0 (.08) 3.0 (.12) 5.5 (.22) 500/100

2x18 (2x1.0) Red H2x1.00/8 2776.0 11.0 (.43) 15.4 (.61) 8.2 (.32) 2.4 (.09) 3.2 (.13) 5.8 (.23) 500/100

2x18 (2x1.0) Red H2x1.00/18 2796.0 21.0 (.83) 25.2 (.99) 18.0 (.71) 2.4 (.09) 3.2 (.13) 5.8 (.23) 500/100

2x16 (2x1.5) Black H2x1.50/8 2777.0 12.0 (.47) 15.8 (.62) 8.2 (.32) 2.6 (.10) 3.6 (.14) 6.5 (.26) 500/100

2x16 (2x1.5) Black H2x1.50/12 2797.0 16.0 (.63) 19.6 (.77) 12.0 (.47) 2.6 (.10) 3.6 (.14) 6.5 (.26) 500/100

2x14 (2x2.5) Blue H2x2.50/10 2778.0 14.0 (.55) 18.5 (.73) 10.0 (.39) 3.3 (.13) 4.5 (.18) 8.0 (.31) 500/100

2x14 (2x2.5) Blue H2x2.50/12 2798.0 17.0 (.67) 20.5 (.80) 12.0 (.47) 3.3 (.13) 4.5 (.18) 8.0 (.31) 500/100

2x12 (2x4.0) Gray H2x4.00/12 2799.0 16.0 (.63) 22.0 (.87) 12.0 (.47) 3.9 (.15) 5.2 (.20) 9.0 (.35) 100

2x10 (2x6.0) Yellow H2x6.00/12 2800.0 18.0 (.71) 23.0 (.91) 12.0 (.47) 5.0 (.20) 6.2 (.24) 11.4 (.45) 100

2x8 (2x10.0) Red H2x10.00/12 2801.0 18.0 (.71) 24.0 (.94) 12.0 (.47) 6.2 (.24) 7.6 (.30) 13.4 (.53) 100

2X6 (2x16.0) Blue H2x16.00/16 2802.0 20.0 (.79) 29.0 (1.14) 16.0 (.63) 8.9 (.35) 9.5 (.37) 17.2 (.68) 100/50

Ferrule AWG Ferrule Ferrule Ferrule Std.Qty. (mm2) Type Cat. No. Color Type Cat. No. Pk.

AB1-S Industry Standard AB1-S 2884.9 150 20 (.50) H0.50/8 2201.0 Orange100 20 (.75) H0.75/8 2202.0 Whiite100 18 (1.00) H1.00/6 2399.0 Yellow100 16 (1.50) H1.50/8 2204.0 Red50 14 (2.50) H2.50/8 2206.0 Blue

AB2-S Industry Standard AB2-S 2885.9 150 12 (.4.0) H4.00/10 2208.0 Gray20 10 (6.0) H6.00/12 2210.0 Black20 8 (10.0) H10.00/12 2212.0 Ivory10 6 (16.0) H16.00/12 2214.0 Green

AB1-D DIN Standard AB1-D 2884.0 150 20 (.50) H0.50/6 2864.0 White100 20 (.75) H0.75/8 2867.0 Gray100 18 (1.0) H1.00/8 2871.0 Red100 16 (1.5) H1.50/8 2841.0 Black50 14 (2.5) H2.50/8 2845.0 Blue

AB2-D DIN Standard AB2-D 2885.0 150 12 (4.00) H4.00/10 2848.0 Gray20 10 (6.00) H6.00/12 2851.0 Yellow20 8 (10.00) H10.00/12 2853.0 Red10 6 (16.00) H16.00/12 2855.0 Blue

* Different standard packs are available for manyferrules. To order the desired standard pack, please use the quantity required as a suffix to the Cat. No.

Example: Type H2x0.50/0,Cat. No. 2794.0/100 for a standard pack of 100


Ferrules




TOOLS &FERRULES

To help you do the best job possiblewhen using Altech’s terminal blocks,we put together a selection of usefultools to accomplish just that. Weoffer this as a service to our cus-tomers, since some of the specialtools we offer are hard to find.

Included in this tool selection arewire strippers to safely and quicklyremove insulation from wire andcable and to speed the wire prepara-tion process; semi-automatic andhand operated crimping tools forcrimping ferrules onto wire ends. Ourlarge selection of screwdriversinclude insulated and uninsulatedstraight blade, flat tip and Phillipstypes.

All tools are made from the highestquality steels for superior perform-ance and long life. The hand toolsare manufactured to exacting speci-fications and carefully heat treatedfor maximum strength and durability.


Universal Ferrule CrimperFront Conductor EntryOne die crimps a wide range of insulated and uninsulated ferrulesizes.Three Universal Ferrule Crimpers are offered to crimp differentferrule and wire size ranges up to 16mm2 (6 AWG).

• Positive ratcheting with spring return•Trapezoidal crimp geometry• Comfort grip plastic handle• Hardened steel frame, matte black

Ferrule CrimperSide Conductor EntryIndividual crimp cavities conform to industry standard insulatedand uninsulated ferrules from 25-50mm2 (4-1 AWG).

• Positive ratcheting with spring return• Emergency release•Trapezoidal crimp geometry• Comfort grip plastic handle• Hardened steel frame, matte black

Universal Ferrule Crimper Universal Ferrule CrimperUniversal Ferrule Crimper

Part No. Wire/ Ferrule Std.AWG mm2 Pk.

E110.000 26 - 10 0.14 - 6 1

Replacement Spring Set:185140008 Handle Spring Set318001002 Rachet Spring


E110.005 20 - 8 0.5 - 10 1



E110.010 8 - 6 10 - 16 1


Ferrule Crimper Ferrule CrimperFerrule Crimper


E110.015 4 - 2 25 - 35 1


E110.020 1 50 1


22.030 2/0-250 70 - 150 1MCM

Crimper Tools

Altech's pneumatic crimping toolsspeed the crimping process of insulat-ed or uninsulated ferrules for a widerange of wire sizes up to 8 AWG.

Altech pneumatic crimpers are simpleand easy to use. Just install the ferruleover the end of the stripped wire andinsert it into either the front or side toolopening.Then touch the actuating leveror push the footswitch pedal to initiatethe crimp cycle. Once the head closes itwill automatically reopen after crimp-ing.The resulting crimp features a com-pact trapezoidal cross section which ismechanically very strong and providesa large surface to insure a highly effi-cient electrical contact.

Crimp ferrules efficiently and economi-cally. A unique dual crimping head pro-vides convenient front or side wireentry, allowing crimping from multiplepositions.This features makes crimpingin tight places simple.

Choose either lever actuated, handheld units or hands-free footswitchoperated table top models, in two basictool sizes. Hand held models feature aflexible coil air-hose with 1/4" NPTinterchange connector for quick hook-up with a standard push-to-connectcoupler.

The table top units also include a flexi-ble coil air hose to the footswitch and a1/4" NPT interchange located on thefootswitch for one hand push-to-con-nect supply hook-up. They feature asturdy metal base with integral tableclamp and dual storage trays for quickaccess to the ferrule supply. The airrelease port on the footswitch has beenquieted with a sintered bronze airsilencer. The footswitch has a metalframe and a tough fiberglass shroud.Its spring return pedal provides forshort actuating cycles.

Optional items for the hand heldcrimper include a counterbalance formaximum control and a magnetic hold-er for storage.

• Operates on 60 - 90 psi air supply• Crimp insulated and uninsulatedferrules

• Trapezoidal crimp geometry• Flexible coil air hose with 1/4"NPT interchange

• Metal tool body and base• Hardened steel crimp head

Wire/ Ferrule Size Tool Wt.Tool AWG mm2 Type Cat. No. g (lbs.) Std. Pk.

Hand Held Crimper with Actuating Lever ACT2.5-P 22.014 430 (.95) 1Crimp Insulated Ferrules 24-14 0.25-2.5and Uninsulated Ferrules

Hand Held Crimper with Actuating Lever ACT10-P 22.015 430 (.95) 1Crimp Insulated Ferrules 12-8 4.0-10.0and Uninsulated Ferrules

Table Top Crimper with Footswitch and Storage Trays ACT2.5-T 22.016 1000 (2.20) 1Crimp Insulated Ferrules 24-14 0.25-2.5and Uninsulated Ferrules

Table Top Crimper with Footswitch and Storage Trays ACT10-P 22.017 1000 (2.20) 1Crimp Insulated Ferrules 12-8 4.0-10.0and Uninsulated Ferrules

Magnetic Mounting Holder ACT-DXP 22.018 --- 1for hand held pneumatic crimpers

Counterbalance CT-DUP 22.019 --- 1for hand held pneumatic crimpers


Pneumatic Crimping Tool


Key:

ACT10-P

E110.015

E110.020

ACT2.5T-P 2

ACT10T-P

ACT2.5P 2

Wire SizeAWG Cr

imper Type

Ferrule Sizemm2

GFCF

CRIMPER STYLES

VISE MOUNTFERRULECRIMPER

C R I M P E R S E L E C T O R G U I D EFerrule and Wire Size by Crimper Type

E110.000

E110.005

E110.010

UNIVERSAL FERRULECRIMPER

PNEUMATIC FERRULECRIMPER

Use this Selector Guide to determine ferrule and wire sizes which can be crimped. Refer to ordering pages 94-97for additional selection and ordering information.

1. Determine the wire size(s) to be used.

2. Select the appropriate ferrule size(s).1

3. Based on the ferrule size, choose the crimper type appropriate for use. 4. Select the crimper style best suited for your application.

Dual Wire FerrulesE110.000 crimper covers 2x20 to 2x12 AWG dual wire ferrulesE110.010 crimper covers 2x10 to 2x8 AWG dual wire ferrulesE110.015 crimper covers 2x6 AWG dual wire ferrules

= Multi-Cavity RangeX = Individual Cavity

1 To insure efficient ferrule crimping, always select the smallest ferrule diameter that fits the wire.2 Insulated ferrule/wire size range is shown, uninsulated ferrule range is 16-14 AWG (1.50 - 2.5mm2).

26 .14

24 .25

22 .34

20 .50

20 .75

18 1.00

16 1.50

14 2.50

12 4.00

10 6.00

8 10.00

6 16.00

4 25.00

2 35.00

1 50.00

2/0 70.00

3/0 95.00

4/0 120.00

250MCM 150.00

X XX XX X

XX

XXXXX

99Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com

CONVERSION TABLES

DEGREES CELSIUS VERSUS DEGREES FAHRENHEIT

°C °F °C °F °C °F °C °F °C °F °C °F °C °F °C °F °C °F

-80 -112.0 -20 –4.0 5 41.0 30 86.0 55 131.0 80 176.0 105 221.0 130 266.0 200 392-70 -94.0 -19 –2.2 6 42.8 31 87.8 56 132.8 81 177.8 106 222.8 131 267.8 210 410-60 -65.0 -18 –0.4 7 44.6 32 89.6 57 134.6 82 179.6 107 224.6 132 269.6 220 428-50 -58.0 -17 +1.4 8 46.4 33 91.4 58 136.4 83 181.4 108 226.4 133 271.4 230 446-45 -49.1 -16 3.2 9 48.2 34 93.2 59 138.2 84 183.2 109 228.2 134 273.2 240 464

-40 -40.0 -15 5.0 10 50.0 35 95.0 60 140.0 85 185.0 110 230.0 135 275.0 250 482-39 -38.2 -14 6.8 11 51.8 36 96.8 61 141.8 86 186.8 111 231.8 136 276.8 300 572-38 -36.4 -13 8.6 12 53.6 37 98.6 62 143.6 87 188.6 112 233.6 137 278.6 350 662-37 -34.6 -12 10.4 13 55.4 38 100.4 63 145.4 88 189.4 113 235.4 138 280.4 400 752-36 -32.8 -11 12.2 14 57.2 39 102.2 64 147.2 89 192.2 114 237.2 139 282.2 500 932

-35 -31.0 -10 14.0 15 59.0 40 104.0 65 149.0 90 194.0 115 239.0 140 284.0 600 1112-34 -29.2 -9 15.8 16 60.8 41 105.8 66 150.8 91 195.8 116 240.8 141 285.8 700 1292-33 -27.4 -8 17.6 17 62.6 42 107.6 67 152.6 92 197.6 117 242.6 142 287.6 800 1472-32 -25.6 -7 19.4 18 64.4 43 109.4 68 154.4 93 199.4 118 244.4 143 289.4 900 1652-31 -23.8 -6 21.2 19 66.2 44 111.2 69 156.2 94 201.2 119 246.2 144 291.2 1000 1832

-30 -22.0 -5 23.0 20 68.0 45 113.0 70 158.0 95 203.0 120 248.0 145 293.0 1100 2012-29 -22.0 -4 24.8 21 69.8 46 114.8 71 159.8 96 204.8 121 249.8 146 294.8 1200 2192-28 -18.4 -3 26.6 22 71.6 47 116.6 72 161.6 97 206.6 122 251.6 147 296.6 1300 2372-27 -16.6 -2 28.4 23 73.4 48 118.4 73 163.4 98 208.4 123 253.4 148 298.4 1400 2552-26 -14.8 -1 30.2 24 75.2 49 120.2 74 165.2 99 210.2 124 255.2 149 300.2 1500 2732

-25 -13.0 0 32.0 25 77.0 50 122.0 75 167.0 100 212.0 125 257.0 150 302.0 1600 2912-24 -11.2 1 33.8 26 78.8 51 123.8 76 168.8 101 213.8 126 258.8 160 320.0 1700 3092-23 -9.4 2 35.6 27 80.6 52 125.6 77 170.6 102 215.6 127 260.6 170 338.0 1800 3272-22 -7.6 3 37.4 28 82.4 53 127.4 78 172.4 103 217.4 128 262.4 180 356.0 1900 3452-21 -5.8 4 39.2 29 84.2 54 129.2 79 174.2 104 219.2 129 264.2 190 374.0 2000 3632

Conversion Formula °F = 9/5°C + 32° °C = 5/9(°F–32°)

Metric Cross- American Wire Gauge Metric Cross- American Wire GaugeSectional Areas a Sections Areas a

Cross-Sectional Equivalent AWG or MCM Cross-Sectional Equivalent AWG or MCMArea Metric Area Area Metric Areamm2 mm2 mm2 mm2

0.5190.6530.823

1.041.31

1.652.08

2.62

3.314.175.26

6.638.37

10.5513.3016.77

20 AWG1918

1716

1514

13

121110

98

765

21.1526.6733.63

85.03

107.20126.64152.00177.35202.71253.35

380.00

506.71

0.50

0.75

1.5

2.5

4.0

6.0

10.0

16.0

4 AWG32

3/0

4/0250 MCM300350400500

750

1000

25.0

35.0

50.0

70.0

95.0

120.0

150.0

185.0

240.0

300.0400.0

500.0625.0

aAs per IEC Publ. 228

Lengthinch [in.] x 25.4 =millimetersmillimeters [mm] x 0.03937 =inchesmeters [m] x 3.281 =feetmiles [mi] x 1.609 =kilometerskilometers [km] x 0.6214 =miles

TorqueNewtonmeter [Nm] x 0.738=lb-ftlb-ft x 1.356 =Nmlb-in x 0.113 =Nmoz-in x 0.0071 =Nm

Powerkilowatt [kW] x 1.341 =hphp x 0.7457 =kW

Moment of Inertia (WR2)lb-ft2 x 0.042 =kgm2

kilogrammeter2 23.720 =lb-ft2[kgm2]

Weight Mass and ForceNewton [N] x 0.2248 =poundkilogram [kg] x 2.205 =poundspound [lb] x 4.448 =Npound [lb] x 0.4536 =kg

67.432/0

53.48 1/0

42.41 1


oooooooooooooooooooooooooooooooooooooooooooooooo

Total Length (3)

Internal Jumpers

External Jumpers (AQ)

??

?

?

?

?

?

? 6.3mm (.25 in.)

Ground Blk CGT4U 1 6 6

Feed Through CTS25U 1 12 12

End Plate EP25U 1 2 2

Feed Through CTS6U 2 8 16

End Plate EP6/10U 1 1.5 1.5

Feed Through CTS4U-N/R 1 6 6

Feed Through CTS4U-N/W 1 6 6

Feed Through CTS4U-N/BU 1 6 6

Feed Through CTS4U-N/BL 1 6 6

Feed Through CTS4U-N 5 6 30

Disconnect CKT4U 1 6 6

Fuse Block CSFL4U(L) 1 8 8

Double Level Block CDL4U 1 6 6

End Plate EPCDL4U 1 2.5 2.5

End Stop CA702 1 9 9

External Jumper 2P CA714/2 1 - -

Internal Jumper 3P CA722/3 1 - -

Push on Marker - -

123

125

22

67

89

13

45

3911

125

22

67

89

13

45

3911

163

173

Bill of Material

Component Cat. No. Qty. Width Ext.Description Ea. Width

(mm) (mm)

?

?

?

25mm(.98 in.)

a Other slot and hole configurations available, please consult Altech.b Based on standard 8 mm slots.

Mounting Centers (4)

Indicate the specific positions of all terminal blocks and accessories selected. Include terminal markings, external andinternal jumpers.

A = Total

••

EXAMPLE

Std. Slots a - 6.3 x 8mm(.25 x .32 in.)

Marking

?

?

25mm(.98 in.)

?

DIN Rail Ordering InformationCat. No. (3) Length (mm)

2511120 173

DIN Rail Length Calculation mm(1) Std. Mounting Allowance at Ends = 25mm x 2 50

(2) Total Width of Components = A 123

(3) Total Length (Rail) = (1) + (2) 173

(4) Mounting Centers = (3) – 10mm b 163

DIN RAIL ASSEMBLY WORKSHEET

Company: _______________________________________________

Address: ________________________________________________

_________________________________________________

Phone: (____)________________ FAX: (____) _________________

Contact:_________________________________________________

135 East Front St.

York, PA 17405

Doug Jones, EE

B.L. Products Company

717 555-8086 717 555-8087

CGT4U

CTS25U

EP25U

CTS6U

CTS6U

EP6/10U

CTS4U-N/R

CTS4U-N/W

CTS4U-N/BU

CTS4U-N/BL

CTS4U-N

CTS4U-N

CTS4U-N

CTS4U-N

CTS4U-N

CKT4U

CSFL4U(L)

CDL4U

EPCDL4U

CA702

101Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com

oooooooooooooooooooooooooooooooooooooooooooooooo

Total Length (3)

Internal Jumpers (Q)

External Jumpers (AQ)

??

?

?

?

?

?

? 6.3mm (.25 in.)

Bill of Material

Component Cat. No. Qty. Width Ext.Description Ea. Width

(mm) (mm)

?

?

?

25mm(.98 in.)

a Other slot and hole configurations available, please consult Altech.b Based on standard 8 mm slots.

Mounting Centers (4)

Indicate the specific positions of all terminal blocks and accessories selected. Include terminal markings, external andinternal jumpers.

A = Total

Std. Slots a - 6.3 x 8mm(.25 x .32 in.)

Marking

?

?

25mm(.98 in.)

?

DIN Rail Ordering InformationCat. No. (3) Length (mm)

DIN Rail Length Calculation mm

DIN RAIL ASSEMBLY WORKSHEET

DIN Rail Length Calculation mm(1) Std. Mounting Allowance at Ends = 25mm x 2

(2) Total Width of Components = A

(3) Total Length (Rail) = (1) + (2)

(4) Mounting Centers = (3) – 10mm b

Company: _______________________________________________

Address: ________________________________________________

_________________________________________________

Phone: (____)________________ FAX: (____) _________________

Contact:_________________________________________________


IMPRINT SCHEDULE FOR CUSTOM MARKING TAGS*

Cat. No. Tag DimensionsHorizontal Imprint W x H MT 2/H- XX 4.9 x 5.8MT 3/H- XX 5.0 x 10.0 MT 4/H- XX 5.0 x 4.8MT 5/H- XX 9.4 x 4.5MT 6/H- XX 9.4 x 5.5MT 8/H- XX 10.4 x 7.3MT 9/H- XX 10.3 x 8.7MT 10/H- XX 10.4 x 9.4MT 12/H- XX 10.4 x 11.3MT 15/H- XX 10.4 x 14.3MT 20/H- XX 4.9 x 20MT 25/H- XX 4.9 x 25

Ordering Instructions

1) Indicate Tag Type (Use separate sheet for each Tag Typeordered).2) List imprint sequence for each strip. (Please use Typewriter)3) Indicate strip quantity for each strip.4) Indicate total strip quantity.5) Mail or FAX form with Purchase Order to Altech.

* SSEETT--UUPP FFEEEE AAPPPPLLIIEESS TTOO CCUUSSTTOOMM IIMMPPRRIINNTTSS..

A

B

C

D

E

F

G

H

I

J

1

Strip Qty.

A

B

C

D

E

F

G

H

I

J

2

Strip Qty.

A

B

C

D

E

F

G

H

I

J

3

Strip Qty.

A

B

C

D

E

F

G

H

I

J

4

Strip Qty.

A

B

C

D

E

F

G

H

I

J

5

Strip Qty.

A

B

C

D

E

F

G

H

I

J

6

Strip Qty.

Strip Qty.

A B C D E F G H I J

L

w

X917

233 HORIZONTALX917

240

X917

232

X917

241

A B C D E F G H I J

L

w

VERTICAL49T6019

49T6020

49T6027

49T6028

Cat. No. Tag DimensionsVertical Imprint W x H MT 2/V- XX 4.9 x 5.8MT 3/V- XX 5.0 x 10.0 MT 4/V- XX 5.0 x 4.8MT 5/V- XX 9.4 x 4.5MT 6/V- XX 9.4 x 5.5MT 8/V- XX 10.4 x 7.3MT 9/V- XX 10.3 x 8.7MT 10/V- XX 10.4 x 9.4MT 12/V- XX 10.4 x 11.3MT 15/V- XX 10.4 x 14.3MT 20/V- XX 4.9 x 20MT 25/V- XX 4.9 x 25

Company: _______________________________________________

Address: ________________________________________________

_________________________________________________

Phone: (____)________________ FAX: (____) _________________

Contact:_________________________________________________

Documents

AltechCorp - DIN Rail and Panel Mount Terminal Blocks