Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
TechnicalPDF Published October 17, 2013
55 Guardsman Road Thornhill, Ontario Canada, L3T 6L2
t. 905.889.7890 f. 905.889.8553 [email protected]
Page
Technical Specifications i-x
Pipe 1
Socket Fusion Fittings Couplings 1 90o elbows 2 45o elbows 2 Tees 3 Reducing tees 3 Concentric reducers 4 End caps 5 Threaded adaptors 6 ANSI flange adaptors 7 ANSI backing rings 7 Metric flange adaptors 8 Metric backing rings 8
Electro Fusion Fittings Couplings 9
Valves Ball valves 10
Non-ANSI Fittings 90o elbow adaptors 11 Male threaded adaptors-R thread 12 Threaded adaptors-R thread 13
Piping Supports Pipe clips 14-15
10/13 ©Chemline Plastics Limited 2013Chemline is a registered trademark of Chemline Plastics Limited
ISO 9001:2008 Certified
AirPro® Compressed Air Piping SystemPipe, Fittings + Pipe Supports
i Price List AD08-1
Advantages of AirPro®
AirPro® piping systems are specifically designed for compressed air and has CRN certification. AirPro® is made of Solvay Eltex TUB 124 blue high density polyethylene (HDPE) resin and is extremely ductile, light weight, corrosion resistant and creates minimal system pressure drop. Installation is faster, more flexible and installed cost is lower than metal systems.AirPro® is not affected by condensate and moist environments which cause most metal systems to scale, pit or corrode, resulting in increased system pressure drop. It is chemically resistant to synthetic and mineral oils in the air released by compressors1.PE 100 provides excellent chemical resistance to a multitude of acids, alkalies and hydrocarbons. 1 Consult factory for actual recommendations.
Features of AirPro® Systems excellent resistance to compressor oils and moist ambient air excellent stress cracking resistance high impact resistance wide temperature range (between –50°C and +60°C) installation is fast, flexible, and low cost corrosion resistant low frictional resistance lower flow noise level
Other Features low specific weight of 0.96g/cm³, (PVC 1.40g/cm³, steel 7.86 g/cm³) very good chemical resistance high weathering resistance no conductivity very good abrasion resistance frost resistant very good thermal insulating property rodent resistant resistant to any microbial corrosion
UV StabilityAir-Pro is recommended for indoor application only as PE100 is affected by direct sunlight over time. For outdoor installation make sure that Air-Pro is sufficiently protected against UV by using a UV-resistant (generally black) insulation material.
technicalAirPro® Compressed AirPiping System
Price List AD09-1 ii
Permissible Operating Pressures for AirPro®
AirPro® piping systems are designed for continuous operating temperature of 20°C at a maximum operating pressure of 230 psi (16 bar). The values detailed in the table show the acceptable permanent pressure for pipe and fittings in industrial compressed-air piping systems for a particular operating temperature and operating period.
Specific Material Properties of PE100
Operating Temperature
Operating Periods(Years)
Permissible Operating Pressure
50
50
50
15
5
(oC)
20
30
40
50
60
(oF)
68
86
104
122
140
(psi)
230
200
180
165
150
(bar)
16.0
14.0
12.5
11.4
10.3
PhysicalProperty
Mec
hani
cal P
rop
erti
esTh
erm
al
Pro
per
ties
Ele
ctri
cal
Pro
per
ties
Specific Density at 23oC
Melt Flow Index
MFR 230/5
Tensile Stress at Yield
Elongation at Yield
Elongation at Break
Impact Strength unnotched at 23oC
Impact Strength unnotched at –30oC
Impact Strength notched at 23oC
Impact Strength notched at –30oC
Ball indentation hardness acc. Rockwell
Flexural strength
Modulus of elasticity
Vicat-Softening point VST/B/50
Heat deflection temperature HDT/B
Linear coefficient of thermal expansion
Thermal conductivity at 20°C
Flammability
Specific volume resistance
Specific surface resistance
Relative dielectric constant at 1 MHz
Dielectric strength
Physiologically non-toxic
FDA
UV Stabilized
Colour
Standard
ISO 1183
ISO 1133
ISO 527
ISO 527
ISO 527
ISO 179
ISO 179
ISO 2039-1
ISO 178
ISO 527
ISO 306
ISO 75
DIN 53752
DIN 52612
UL94
DIN 4102
VDE 0303
VDE 0303
DIN 53483
VDE 0303
ECC 90/128
–
–
–
Unit
g/cm3
g/10min
MPa
psi
%
%
kJ/m2
kJ/m2
MPa
psi
MPa
psi
MPa
psi
°C
°C
10-4 / °C
W/(mxK)
–
–
ohm cm
ohm
–
kV/mm
–
–
–
–
PE100
0.95
6
25
3,625
9
>600
no break
no break
16
6
46
6,670
24
3,480
1,100
159,500
77
75
1.8
0.4
94-HB
B2
>1016
>1013
2.3
70
yes
yes
yes
blue
technicalAirPro® Compressed AirPiping System
iii Price List AD08-1
Pipe SizingDesigning pipe line sizes for a compressed air system is considerably different from designing a fluid system. Gases are compressible, so there are more variables to be considered. Designs should take current and future demands into account to prevent unnecessary pressure drops. Elevated pressure drops represent unrecoverable energy and financial losses.
Main LinesNormal compressed air systems incorporate two types of lines, the mains and the branches. A generally accepted value for velocity through a main air line is 6 meters per second. The main lines are used to carry the bulk of the compressed air and undersizing them can create large pressure drops and high velocities throughout the system. Undersized mains can also cause additional problems from condensed water as high air velocities can pick up this water and carry it down the line. In general, systems should be oversized rather than undersized. Oversizing will create a greater initial expense but will generally prove to be cost effective over time. Properly sized mains reduce pressure drop and velocity and the extra volume acts as an added receiver, reducing compressor demand and allowing for future expansion.
FittingsFittings (such as 90° elbows) increase the flow resistance and pressure drop of the complete system caused by the change in flow direction. The influence of the fittings can be calculated by means of equivalent lengths which can then be added to the pipe length using the following formula.
For the equivalent lengths please refer to the table below.
Equal Pipe Length in (m)Fitting
45° elbow
90° elbow
Tee main direction
Tee branch
Reducer
Ball valve
da20
0.2
0.8
0.3
0.9
0.0
0.1
0.30
1.12
0.35
1.30
0.03
0.12
da25
0.3
1.0
0.3
1.2
0.0
0.1
da32
0.3
1.3
0.4
1.5
0.0
0.1
da40
0.4
1.6
0.5
1.9
0.1
0.2
da50
0.5
2.0
0.6
2.4
0.1
0.2
da63
0.7
2.6
0.8
3.0
0.1
0.3
da75
0.8
3.1
0.9
3.5
0.1
0.3
da90
1.0
3.7
1.1
4.2
0.1
0.4
da110
1.2
4.5
1.4
5.2
0.2
0.5
Lequ. = x di
x 1,000
Lequ. = equivalent length (m)di = pipe inside diameter (mm) = drag coefficient
= coefficient of friction = 0.02
Standard Size Range
OutsideThickness
s (mm)
20
25
32
40
50
2.8
3.5
4.4
5.6
6.9
Inside
14.4
18.0
23.2
28.8
36.2
Thickness s (mm)
63
75
90
110
8.7
10.3
12.5
15.2
45.6
54.4
65.0
79.6
Pipe Diameter (mm)
Outside Inside
Pipe Diameter (mm)
technicalAirPro® Compressed AirPiping System
Price List AD08-1 iv
Nomogram for Calculation of Pipe Outside Diameter
Approximation formula for calculating Pipe Inside DiameterThe pipe inside diameter is normally calculated by means of an approximation formula assuming that the compressed-air temperature is equivalent to the intake temperature.
A suitable approximation can be achieved by the following equation:
A second method is to calculate the pipe outside diameter by using a nomogram based on the formula above. The nomogram shown is specially adapted to Air-Pro pipes and relates directly to the required outside diameter. The outside diameter can be calculated by entering the known parameters such as pressure drop, operating pressure, flowrate and length of piping system. The use of the outside diameter is advantageous as a subsequent conversion from inside to outside diameter is no longer required. Another advantage of the nomogram is to find the fifth parameter when four parameters are known.
di = 450 x L x V1.85
Δp x p
di = pipe inside diameter (mm)L = nominal length of pipeline (m)V = flow rate (l/sec)Δp = pressure drop (bar)p = excess operating pressure (bar)
63
90
0.002 0.01 0.05 0.1 0.2 0.5 1
1
1.5
2
3
5
10
15
20
30
50
100
20001000500200100502010521
50
40
32
25
20
200
300
400
5002 4 6 10 15
75
110
5
Length of the pipe (L) in meters
Pressure decrease in the pipe (delta P) in bar
Vol
umet
ric fl
ow r
ate
(V) i
n l/
sec
Out
sid
e p
ipe
dia
mte
er (O
D) i
n m
m
Working pressure (P) in bar
technicalAirPro® Compressed AirPiping System
v Price List AD08-1
Supporting DistancesThe support distances normally depend on the mechanical properties of the pipe material, the pipe dimension, the specific weight of the flow media, the operating temperature and the piping layout. The support distances shown in the table refer to compressed air with a density of 1.3 kg/m³. The calculation of the support distances is based on a maximum deflection between two pipe supports of Length (L)/500.
To achieve wider support distances especially for smaller pipe diameters (da 20 – 40mm), continuous pipe supports can be used.
For vertical piping the specified distances can be increased by about 50%.
Thermal Expansion and Flexibility AnalysisThermoplastic materials will expand and contract with changes in temperature. Note: This could be a temperature change from the initial installation temperature.
To calculate the expected expansions, use the following simplified equation and type into the fields below:
Support Distances for the AirPro® Pipe
Outside
Pipe Diameter (mm) Thickness s (mm) 20oC / 68oF
Support Distance L in (mm)
20
25
32
40
50
63
75
90
110
2.8
3.5
4.4
5.6
6.9
8.7
10.3
12.5
15.2
830
960
1,140
1,320
1,530
1,790
2,010
2,270
2,590
30oC / 86oF
790
920
1,000
1,260
1,460
1,700
1,910
2,160
2,470
40oC / 104oF
730
850
1,000
1,160
1,350
1,570
1,770
2,000
2,280
50oC / 122oF
660
770
900
1,050
1,220
1,420
1,600
1,800
2,060
60oC / 140oF
640
740
880
1,010
1,180
1,380
1,550
1,740
1,990
�L = x � T x L
�L = change in length due to the temperature change (mm) .......................................................................
= linear coefficient of expansion (for AirPro® PE100 = 0.18 mm/m x oC) ..................................................
�T = difference in temperature (oC) ...............................................................................................................L = pipe length (m) ......................................................................................................................................
Inside
14.4
18.0
23.2
28.8
36.2
45.6
54.4
65.0
79.6
mm
0.18oC
m
technicalAirPro® Compressed AirPiping System
0.000.180.000
Price List AD08-1 vi
Design of Expansion Loops and OffsetsTo accommodate large expansions in long straight runs of pipe, an expansion loop or offset can be designed into a system. To determine the size of a loop or offset, use the following two equations and type into the fields below:
Condensate DrainerCondensate can form due to temperature and pressure changes (especially in systems without effective air drying) and can cause problems with corroding and damaging of equipment.
The most cost-effective solution to prevent water from entering the branch lines is to use goose neck fittings for the installation of tees, drawing air off the top of the main line, leaving condensed water. A water drainer which offers better protection can also be used for complicated piping systems.
Testing a SystemTesting an Air-Pro system can take place shortly after the installation is complete (normally one hour after the last weld) because the joining procedure does not require a curing time.
The system should be brought up to 50 psi and checked for leaks. The test should continue in gradual steps of 10 psi until the desired pressure is reached (usually 1.5 times design pressure). Each joint should be checked using a soap solution that will bubble if a leak is present.
Note: There will be some gradual drop in pressure due to the natural creep and elongation of the pipe wall as well as the compression of the air.
Hold pressure for 1 hour. If the pressure has decreased without any indication of a leak, increase it to the original level. If pressure loss is not evident, continue testing for a minimum of 2 hours to a recommended duration of 12 hours.
Expansion Loop:
A = =
Offset:A =
Expansion Loop Offsetda x � LC
2da x � LC
A = minimum straight length (mm)
C = material-based constant (for PE100 = 26)
da = pipe outside diameter (mm) ........................
ΔL = change in length (mm) .................................
=
mm
mm
technicalAirPro® Compressed AirPiping System
0
0.00
2600
vii Price List AD08-1
Installation
Welding ProcedureThe AirPro® light weight design allows for easy installation and is assembled using socket fusion equipment. For socket welding, the pipe end and socket fittings are heated to welding temperature by means of a socket and spigot heater inserts. Socket welding may be manually performed on pipe diameters up to 2.0” (63 mm). Larger sizes require a Bench Socket Tool due to the required joining forces. In sizes greater than 1”, a bench style machine may be preferred for ease of operation.
Socket fusion is fairly tolerant to weather conditions and is simple to do. Untrained personnel can be trained in a short period of time to make consistent and reliable joints. Mechanically the welds are reliable, and fairly easy to inspect. Socket fusion is ideal for smaller systems and is quite simple and practical for welding 1/2” to 1”. Systems consisting primarily of 3” and 4” are better suited for butt fusion, as the equipment is smaller and easier to use in tight locations.
Socket Welding ProcedureA brief procedure is outlined below for welding AirPro® systems.
1) A. Assemble tool with appropriate heater inserts for the pipe size to be welded. Prepare work area and, if available, insert heater in a vice for easier usage (hand held machine).
B. Plug in the heater (110VAC) and heat to a temperature between 250 to 270oC (482 to 518oF).
2) A. Cut the pipe faces at right angles and remove the burrs with a deburring tool. For sizes 1-1/4” and larger the ends of the pipe must be chamferred using a scraper tool. Work the pipe face until the blades of the scraper are flush with the pipe end.
B. Clean the pipe and fitting surfaces with lint free paper and isopropyl alcohol.
C. Mark the depth of the socket on the pipe in order to ensure that the pipe is inserted to the correct depth during heating (per chart).
D. Clean heater inserts and check the unit’s temperature.
3) A. Align the pipe and fitting in the machine with the heating element inserts.
B. Quickly and smoothly push the fitting and pipe in an axial direction until the fitting bottoms out and the pipe reaches the marked depth (per chart).
C. Heat for the indicated times (per chart).
D. After heating time is finished, quickly remove pieces from the heater and fit them together until pipe has been inserted to the mark. Allow time to cool (per chart).
AirPro® Welding Parameters
Pipe Outside Diameter (mm)
20
25
32
40
50
63
75
90
110
AdjustingTime (sec)
4
4
6
6
6
8
8
8
10
Insertion Depth (mm)
14
15
17
18
20
26
29
32
35
Pre-Heating Time (sec)
5
7
8
12
18
24
30
40
50
Pipe Chamfer (mm)
2
2
2
2
2
3
3
3
3
Cooling Time Fixed (sec)
6
10
10
20
20
30
30
40
50
Cooling Time Sum (min)
2
2
4
4
4
6
6
6
8
Schematic of Socket Fusion Welding Process
WeldPreparation
Heating Element
FittingPipe
Alignmentand Pre-Heating
Joiningand Cooling
technicalAirPro® Compressed AirPiping System
Price List AD08-1 viii
Installation
Electrofusion Welding ProcedureIn electro-fusion welding, special socket couplings with integrated resistance wires are used. When a current is applied to the outer terminals on the couplings, the wires heat up and weld the socket to the pipes, resulting in a smooth surface. This welding method features low voltage, ease of use and high automation. Welders have bar code identification to automatically set the level and duration of the welding current during the welding process and stores them for use in assemblies where traceability of each weld is necessary.
Detachable Joints
Flanges Unions
technicalAirPro® Compressed AirPiping System
ix Price List AD08-1
Reference Projects
BMW Engine Factory, Steyr, AustriaMaterial: PE 100 blue
Dimension: 20mm to 110mm
Operating pressure: 120 psi (8 bar)
The pipeline for compressed air in the largest engine factory of the BMW group all done with Air-Pro PE 100 blue pipe and fittings in sizes from 20mm up to 110mm. The piping system is designed for maximum operating pressure of 120 psi (8 bar) and a life time of more then 50 years. All pipe and fittings are welded together through socket welding and electro fusion welding.
technicalAirPro® Compressed AirPiping System
Price List AD08-1 x
Reference Projects
Limestone Factory, SermuthMaterial: PE 100 blue
Dimension: 63mm to 110mm
Operating pressure: up to 16 bar
Length: 500 m
The pipeline for compressed air for different work stations all done with AirPro® PE 100 blue pipe and fittings in sizes from 63mm to 110mm. The piping system is designed for maximum operating pressure of 230 psi (16 bar) and a life time of more then 50 years. All pipe and fittings are welded together through socket welding and electro fusion welding.
BMW Leipzig, GermanyMaterial: PE 100 blue
Dimension: 63mm to 180mm
Operating pressure: up to 16 bar
Length: 8,400 m
The complete underground pressure piping system for compressed air supply in the BMW factory has been done with AirPro® PE 100 blue pipe and fittings. All pipe and fittings are welded together through socket welding and electro fusion welding.
technicalAirPro® Compressed AirPiping System
mm
2.8
3.5
4.4
5.5
6.9
8.6
10.3
12.3
15.1
kg/m
0.15
0.24
0.38
0.60
0.94
1.47
2.09
2.99
4.48
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.705.0020.07
AP.705.0025.07
AP.705.0032.07
AP.705.0040.07
AP.705.0050.07
AP.705.0063.07
AP.705.0075.07
AP.705.0090.07
AP.705.0110.07
daOD s Weight
Poids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
75
90
110* Weights are per meter, supplied in 5 meter lengths.* Au mètre, fourni en longueurs de 5 mètres.
TuyauProduit 705Polyethylène Bleu-PE100Expulsé
PipeProduct 705
Blue Polyethylene-PE100Extruded
Socket CouplingsProduct 053
Blue Polyethylene-PE100Injection mouldedSocket welding
Accouplements de douilleProduit 053Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
3
3
3
3
4
2
3
6
6
kg
0.01
0.02
0.03
0.04
0.07
0.11
0.15
0.28
0.39
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.053.0020.07
AP.053.0025.07
AP.053.0032.07
AP.053.0040.07
AP.053.0050.07
AP.053.0063.07
AP.053.0075.07
AP.053.0090.07
AP.053.0110.07
daOD
k WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
75
90
110
tdsp
mm
16.0
18.0
20.0
22.0
24.0
29.0
33.5
37.0
42.0
mm
29.4
35.1
43.2
51.8
64.4
81.3
92.5
115.0
133.8
L
mm
35
39
43
47
52
60
70
79
90
1 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
pipe + socket fusionAirPro® Compressed AirPiping System
90o Elbows Product 051
Blue Polyethylene-PE100Injection mouldedSocket welding
Coudes 90o
Produit 051Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
14
17
20
25
28
35
38
49
57
kg
0.02
0.03
0.05
0.09
0.14
0.27
0.32
0.58
0.88
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.051.0020.07
AP.051.0025.07
AP.051.0032.07
AP.051.0040.07
AP.051.0050.07
AP.051.0063.07
AP.051.0075.07
AP.051.0090.07
AP.051.0110.07
daOD
k WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
75
90
110
tdsp
mm
16
18
20
22
25
28
33
36
43
mm
29.3
35.1
43.2
53.3
65.5
81.0
92.0
113.7
132.5
45° ElbowsProduct 050
Blue Polyethylene-PE100Injection mouldedSocket welding
Coudes 45°Produit 050Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
11.0
14.0
17.0
21.0
26.0
33.0
38.5
46.0
56.0
kg
0.02
0.03
0.04
0.07
0.09
0.19
0.25
0.44
0.68
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2½”
3”
4”
Item No.
AP.050.0020.07
AP.050.0025.07
AP.050.0032.07
AP.050.0040.07
AP.050.0050.07
AP.050.0063.07
AP.050.0075.07
AP.050.0090.07
AP.050.0110.07
daOD
k WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
tdsp
mm
16.0
18.0
20.0
22.0
24.0
29.0
32.5
37.0
42.0
mm
30
35
43
53
65
81
92
113
135
mm
20
25
32
40
50
63
75
90
110
Price List AP08-1 2
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
socket fusion ttingsAirPro® Compressed AirPiping System
TeesProduct 056
Blue Polyethylene-PE100Injection mouldedSocket welding
Pièces en TProduit 056Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
14.0
17.0
21.0
25.0
30.0
36.5
34.0
51.0
57.0
kg
0.03
0.05
0.07
0.11
0.18
0.31
0.46
0.86
1.12
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.056.0020.07
AP.056.0025.07
AP.056.0032.07
AP.056.0040.07
AP.056.0050.07
AP.056.0063.07
AP.056.0075.07
AP.056.0090.07
AP.056.0110.07
daOD
k WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
75
90
110
tdsp
mm
16
18
20
22
24
29
31
37
44
mm
29.1
35.2
43.0
53.0
65.0
81.0
93.0
114.0
134.0
L
mm
60
70
82
94
108
131
155
185
205
Reducing TeesProduct 055
Blue Polyethylene-PE100Injection mouldedSocket welding
Pièces en T réduitesProduit 055Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
68.5
79.7
79.5
89.9
90.5
91.0
110.0
110.0
108.0
107.0
130.0
130.0
130.0
130.0
kg
0.05
0.07
0.07
0.10
0.10
0.10
0.17
0.17
0.17
0.17
0.28
0.29
0.29
0.30
Item No.
AP.055.2520.07
AP.055.3220.07
AP.055.3225.07
AP.055.4020.07
AP.055.4025.07
AP.055.4032.07
AP.055.5020.07
AP.055.5025.07
AP.055.5032.07
AP.055.5040.07
AP.055.6325.07
AP.055.6332.07
AP.055.6340.07
AP.055.6350.07
da/da1OD/OD1
L WeightPoids
tdsp
mm
18
20
20
22
22
22
24
24
24
24
29
29
29
29
t1
mm
16
16
18
16
18
20
16
18
20
22
18
20
22
24
mm
34.8
43.0
43.0
53.0
53.2
53.0
65.4
65.5
65.0
65.0
81.0
81.0
81.0
81.0
dsp1
mm
29.9
29.9
35.0
29.7
35.3
43.0
30.0
35.5
43.0
53.0
36.0
43.5
53.0
66.0
z
mm
31.9
39.8
40.0
44.8
46.8
45.0
50.0
51.0
54.0
52.5
65.0
65.0
65.0
65.0
mm
25/20
32/20
32/25
40/20
40/25
40/32
50/20
50/25
50/32
50/40
63/25
63/32
63/40
63/50
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
3 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
socket fusion ttingsAirPro® Compressed AirPiping System
Concentric ReducersProduct 057
Blue Polyethylene-PE100Injection mouldedSpigot by Socket welding
Réducteurs concentriquesProduit 057Polyethylène Bleu-PE100Moulé à injectionSoudure à broche par douille
mm
39.0
45.5
45.0
50.0
50.0
50.0
55.0
55.0
55.0
55.0
65.0
65.0
65.0
65.0
87.0
64.0
87.8
86.6
90.0
88.7
kg
0.01
0.02
0.02
0.02
0.02
0.03
0.03
0.03
0.04
0.05
0.06
0.07
0.07
0.08
0.14
0.15
0.19
0.19
0.26
0.30
Item No.
AP.057.2520.07
AP.057.3220.07
AP.057.3225.07
AP.057.4020.07
AP.057.4025.07
AP.057.4032.07
AP.057.5020.07
AP.057.5025.07
AP.057.5032.07
AP.057.5040.07
AP.057.6325.07
AP.057.6332.07
AP.057.6340.07
AP.057.6350.07
AP.057.7550.07
AP.057.7563.07
AP.057.9063.07
AP.057.9075.07
AP.057.1163.07
AP.057.1190.07
da/da1OD/OD1
L WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
tdsp
mm
16.0
16.0
18.0
16.0
18.0
20.0
16.0
18.0
20.0
22.0
18.0
20.0
22.0
24.0
24.4
29.0
29.0
32.0
29.0
37.0
W
mm
2.3
2.9
2.9
3.7
3.7
3.7
4.6
4.6
4.6
4.6
5.8
5.8
5.8
5.8
6.8
6.8
8.2
8.2
10.0
10.0
mm
30.0
30.0
35.0
29.5
34.5
42.8
29.4
34.7
43.7
52.8
34.8
42.9
52.8
64.8
65.0
81.5
80.8
93.0
81.2
113.8
mm
25/20
32/20
32/25
40/20
40/25
40/32
50/20
50/25
50/32
50/40
63/25
63/32
63/40
63/50
75/50
75/63
90/63
90/75
110/63
110/90
Price List AP08-1 4
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
W
socket fusion ttingsAirPro® Compressed AirPiping System
mm
29.0
35.0
43.0
52.5
64.5
82.0
92.5
113.0
135.0
kg
0.01
0.01
0.02
0.04
0.07
0.13
0.16
0.29
0.44
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
daOD
dsp
mm
32
38
47
58
70
87
98
119
141
d2 WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
75
90
110
L
mm
16
18
20
22
24
29
32
37
42
mm
26
30
35
38
50
59
67
77
94
t
End CapsProduct 054
Blue Polyethylene-PE100Injection mouldedSocket welding
Montures d’emboutProduit 054Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
Item No.
AP.054.0020.07
AP.054.0025.07
AP.054.0032.07
AP.054.0040.07
AP.054.0050.07
AP.054.0063.07
AP.054.0075.07
AP.054.0090.07
AP.054.0110.07
5 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
socket fusion ttingsAirPro® Compressed AirPiping System
Female ThreadedAdaptorsProduct 082.1
With nickel plated brass female NPT threadsBlue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs letésfemellesProduit 082.1Avec laiton plaqué de nickel fileté femelle NPTPolyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
42.0
46.0
53.0
65.5
77.4
90.5
kg
0.14
0.18
0.21
0.33
0.58
0.76
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
Item No.
AP.082.2021.07
AP.082.2526.07
AP.082.3233.07
AP.082.4041.07
AP.082.5051.07
AP.082.6364.07
daOD
dsp WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
L“NPT” t sw
mm
41
41
47
51
58
65
mm
32
36
39
50
60
70
mm
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
mm
16
18
20
22
24
29
L1
mm
14.0
18.0
20.0
21.0
25.5
29.0
mm
42.0
46.0
53.0
65.5
76.0
90.5
kg
0.16
0.20
0.25
0.48
0.66
0.93
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
Item No.
AP.083.2021.07
AP.083.2526.07
AP.083.3233.07
AP.083.4041.07
AP.083.5051.07
AP.083.6364.07
daOD
dsp WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
L“NPT” t sw
mm
57
61
66
71
77
83
mm
32
36
39
50
60
70
mm
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
mm
16
18
20
22
24
29
L1
mm
15.5
19.5
22.0
24.0
27.0
29.0
Male ThreadedAdaptorsProduct 083.1
With nickel plated brass male NPT threadsBlue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs letésmalesProduit 083.1Avec laiton plaqué de nickel fileté males NPTPolyethylène Bleu-PE100Moulé à injectionSoudure à douille
Price List AP08-1 6
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
socket fusion ttingsAirPro® Compressed AirPiping System
ANSI Flange AdaptorsProduct 052.1
Blue Polyethylene-PE100Injection mouldedSocket weldingUsed together with Backing Rings for flange connections.
Adapteurs de bride ANSIProduit 052.1Polyethylène Bleu-PE100Moulé à injectionSoudure à douilleUtilisé avec des adapteurs de bride pour des rac-cordements de bride.
mm
44.5
54.1
63.5
71.5
82.6
100.4
117.0
132.4
170.5
kg
0.01
0.02
0.03
0.05
0.06
0.10
0.15
0.19
0.29
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.052.1020.07
AP.052.1025.07
AP.052.1032.07
AP.052.1040.07
AP.052.1050.07
AP.052.1063.07
AP.052.1075.07
AP.052.1090.07
AP.052.1110.07
daOD
d4 WeightPoids
hd3 t
mm
16
18
20
22
24
29
32
37
42
mm
27.0
33.0
40.8
50.0
61.5
76.6
91.2
105.0
131.0
L
mm
21
23
26
26
30
34
40
40
47
k
mm
5.0
5.0
6.0
4.0
6.0
5.0
8.0
3.5
5.0
mm
20
25
32
40
50
63
75
90
110
mm
95
102
114
130
133
162
184
194
229
kg
0.21
0.24
0.39
0.51
0.55
0.82
1.07
1.07
1.57
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Nom.
2-3/8”
2-3/4”
3-1/8”
3-1/2”
3-7/8”
4-3/4”
5-1/2”
6”
7-1/2”
Item No.
B.013.0020.11
B.013.0025.11
B.013.0032.11
B.013.0040.11
B.013.0050.11
B.013.0063.11
B.013.0075.11
B.013.0090.11
B.013.0110.11
daOD
d WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
mm
20
25
32
40
50
63
75
90
110
d3 bNo. of Bolts
k
mm
12
12
16
16
18
18
18
18
18
Torqueft-lbs.
11.1
11.1
11.1
18.4
25.8
25.8
29.5
29.5
29.5
mm
28
34
42
51
62
78
92
111
133
mm
60
70
79
89
99
121
140
152
191
Nom.
5/8”
5/8”
5/8”
5/8”
5/8”
3/4”
3/4”
3/4”
3/4”
d2
mm
16
16
16
16
16
20
20
20
20
4
4
4
4
4
4
4
4
8
ANSI Backing RingsProduct 013
Grey PPGGlass Filled PolypropyleneInjection Moulded with Steel CoreUsed together with Stub Flanges for flange connections
Anneaux de support de norme ANSIProduit 013PPG-grisPolypropylène rempli de fibre de verreMoulé à injection avec insertion en acierUtilisé avec des brides de moignon pour desraccordementts de bride
mm
10.0
10.0
10.0
10.5
13.0
14.0
16.0
17.0
18.0
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
7 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
socket fusion ttingsAirPro® Compressed AirPiping System
Metric Flange AdaptorsProduct 052
Blue Polyethylene-PE100Injection mouldedSocket weldingUsed together with metric Backing Rings for flanged connections
Adapteurs de bride métriqueProduit 052Polyethylène Bleu-PE100Moulé à injectionSoudure à douilleUtilisé avec des anneaux de support métrique pour des raccordements à brides
mm
45
58
68
77
88
102
121
138
158
kg
0.01
0.02
0.03
0.05
0.06
0.09
0.15
0.20
0.29
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.052.0020.07-M
AP.052.0025.07-M
AP.052.0032.07-M
AP.052.0040.07-M
AP.052.0050.07-M
AP.052.0063.07-M
AP.052.0075.07-M
AP.052.0090.07-M
AP.052.0110.07-M
daOD
d4 WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
hd3
mm
10.0
10.0
10.0
10.5
13.0
14.0
16.0
17.0
18.0
mm
27.0
33.0
40.8
50.0
61.5
76.6
91.2
105.0
131.0
t
mm
16
18
20
22
24
29
32
37
42
mm
20
25
32
40
50
63
75
90
110
mm
15
20
25
32
40
50
65
80
100
kg
0.24
0.31
0.41
0.61
0.69
0.79
1.10
1.22
1.63
Item No.
B.014.0020.11-M
B.014.0025.11-M
B.014.0032.11-M
B.014.0040.11-M
B.014.0050.11-M
B.014.0063.11-M
B.014.0075.11-M
B.014.0090.11-M
B.014.0110.11-M
daOD
DN WeightPoids
4
4
4
4
4
4
4
8
8
No. ofBolts
M12
M12
M12
M16
M16
M16
M16
M16
M16
BoltSizemm
20
25
32
40
50
63
75
90
110
d d3 k
mm
28
34
42
51
62
78
92
108
128
b
mm
12
14
16
18
18
18
18
20
20
mm
95
108
115
140
150
165
187
202
222
d2
mm
14
14
14
18
18
18
18
18
18
Torqueft-lbs.
11.1
11.1
11.1
18.4
25.8
25.8
29.5
29.5
29.5
p
psi
235
235
235
235
235
235
235
235
235
mm
65
75
85
100
110
125
145
160
180
Metric Backing RingsProduct 014
Grey PPGGlass Filled PolypropyleneInjection Moulded with Steel CoreFlange connectionUsed together with Stub Flanges for flange connections
Anneaux de support de norme métriqueProduit 014PPG-grisPolypropylène rempli de fibre de verreMoulé à injection avec insertion en acierRaccordement de brideUtilisé avec des brides de moignon pour desraccordementts de bride
Price List AP08-1 8
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
socket fusion ttingsAirPro® Compressed AirPiping System
Electro Fusion CouplingsProduct 173
Black polyethyleneInjection moulded
Accouplements d’emboitementProduit 173Polyethylène noirMoulé à injection
mm
30
35
42
53
67
83
97
115
140
kg
0.04
0.04
0.05
0.09
0.16
0.25
0.35
0.51
0.82
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2½”
3”
4”
Item No.
AP.173.0020.11
AP.173.0025.11
AP.173.0032.11
AP.173.0040.11
AP.173.0050.11
AP.173.0063.11
AP.173.0075.11
AP.173.0090.11
AP.173.0110.11
daOD
d WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
tL
mm
37.0
40.0
44.0
49.0
55.0
63.0
70.0
70.0
74.5
mm
75
81
89
99
111
127
142
142
152
mm
36.5
37.0
43.0
49.0
53.0
56.0
65.5
74.0
83.0
d1
mm
20
25
32
40
50
63
75
90
110
9 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
electro fusion ttingsAirPro® Compressed AirPiping System
Ball ValvesProduct 335.12
Blue Polyethylene-PE100Injection mouldedSocket welding
Vannes à billeProduit 335.12Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
40.0
51.5
51.5
64.0
73.0
85.0
110.0
132.0
132.0
kg
0.15
0.24
0.29
0.49
0.72
1.12
2.02
3.83
3.90
Nom.
1/2”
3/4”
1”
1-1/4”
1-1/2”
2”
2-1/2”
3”
4”
Item No.
AP.335.1220.07
AP.335.1225.07
AP.335.1232.07
AP.335.1240.07
AP.335.1250.07
AP.335.1263.07
AP.335.1275.07
AP.335.1290.07
AP.335.1211.07
daOD
b WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
hL
mm
71.5
77.0
80.5
98.5
106.5
115.5
142.0
160.0
160.0
mm
99.5
113.0
123.0
140.0
164.0
192.0
231.0
285.0
255.0
d
mm
52.5
62.0
69.5
84.0
100.0
120.5
155.0
187.0
187.0
Materials:End Connectors: Blue PE-100Ball, Stem: Grey PPBody: Blue PPUnion Nuts: Blue PPGSeats: PTFEO-Rings: Viton
Pressure Rating @20oC:20-75mm (1/2” to 2-1/2”): 230 psi90-110mm (32” to 4”): 150 psi
Operators:Locking Handle: StandardElectric or Pneumatic Actuators: Optional
Materiaux:End Connexions: Bleu PE-100Bille, Tige: PP GrisCorps: PP BleuNoix Union: PPG BleuSièges: PTFEJoints: Viton
PressionMaximale @20oC:20-75mm (1/2” à 2-1/2”): 230 psi90-110mm (32” à 4”): 150 psi
Opérateurs:Poignée Cadenassable: Standardationneurs Électriques ou Pneumatiques: Optionnels
mm
20
25
32
40
50
63
75
90
110
Price List AP08-1 10
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
valvesAirPro® Compressed AirPiping System
90o Elbow Adaptorswith brass female R-threadProduct 087
Blue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs en coude 90o avec filets femelles R en laitonProduit 087Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
29.3
35.0
kg
0.08
0.12
Nom.
1/2”
3/4”
Item No.
AP.087.0020.07-R
AP.087.0025.07-R
daOD
dsp WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
dsp1R
mm
39
46
inch
1/2”
3/4”
k
mm
37
40
k1
mm
37
37
mm
20
25
90o Elbow Adaptorswith brass male R-threadProduct 086
Blue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs en coude 90o avec filets males R en laitonProduit 086Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
30
kg
0.13
Nom.
1/2”
Item No.
AP.086.2020.07-R
daOD
dsp WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
dR
mm
38
inch
1/2”
L4
mm
16
sw
mm
32
mm
20
Adapteurs en coude 90o Avec monture et filets males R en laitonProduit 081.1Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
28.3
kg
0.08
Nom.
1/2”
Item No.
AP.081.1020.07-R
daOD
dsp WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
dsp1R
mm
39
inch
1/2”
L2
mm
57.9
L3
mm
49.7
mm
20
90o Elbow AdaptorsWith bracket and brass male R-ThreadProduct 081.1
Blue Polyethylene-PE100Injection mouldedSocket welding
11 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
non-ANSI ttingsAirPro® Compressed AirPiping System
Male Threaded Adaptors R-ThreadProduct 083.20
Blue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs letés males lets RProduit 083.20Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
66
71
77
83
kg
0.27
0.48
0.65
0.94
Nom.
1”
1-1/4”
1-1/2”
2”
Item No.
AP.083.3232.07-R
AP.083.4040.07-R
AP.083.5050.07-R
AP.083.6363.07-R
daOD
L WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
swdsp
mm
39
50
60
70
mm
53.0
65.5
77.0
90.5
R
inch
1”
1-1/4”
1-1/2”
1-1/2”
mm
32
40
50
63
Tees R-ThreadProduct 097
Blue Polyethylene-PE100Injection mouldedSocket welding
Pièces en T lets RProduit 097Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
39.5
39.5
39.5
39.5
kg
0.09
0.10
0.12
0.18
Nom.
1/2”
3/4”
1”
1-1/4”
Item No.
AP.097.0020.07-R
AP.097.0025.07-R
AP.097.0032.07-R
AP.097.0040.07-R
daOD
dsp1 WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
zdsp
mm
45.5
45.5
52.0
56.0
mm
29.5
35.5
43.4
53.5
mm
61.0
70.5
80.5
92.0
LR
inch
1/2”
1/2”
1/2”
1/2”
mm
20
25
32
40
Price List AP08-1 12
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
non-ANSI ttingsAirPro® Compressed AirPiping System
Female Threaded Adaptors R-ThreadProduct 082
Blue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs letés femmelle lets RProduit 082Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
47
51
58
65
kg
0.20
0.34
0.60
0.76
Nom.
1”
1-1/4”
1-1/2”
2”
Item No.
AP.082.3232.07-R
AP.082.4040.07-R
AP.082.5050.07-R
AP.082.6363.07-R
daOD
L WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
swdsp
mm
39
50
60
70
mm
53.0
65.5
77.4
90.5
R
inch
1”
1-1/4”
1-1/2”
2”
mm
32
40
50
63
Male Threaded Adaptors R-ThreadProduct 083
Blue Polyethylene-PE100Injection mouldedSocket welding
Adapteurs letés males lets RProduit 083Polyethylène Bleu-PE100Moulé à injectionSoudure à douille
mm
63
63
kg
0.10
0.15
Nom.
1/2”
3/4”
Item No.
AP.083.0020.07-R
AP.083.0025.07-R
daOD
L WeightPoids
SDR 7.4 / ISO S-3.2 / Maximum Operating Pressure 235 psi (16 bar)
dsp
mm
29.3
35.0
L1
mm
16.5
16.5
dsp1
mm
39
39
R
inch
1/2”
3/4”
mm
20
25
13 Price List AP08-1
**Indicates regularly stocked items.Consult Chemline Plastics for availability.
Subject to change without notice.
non-ANSI ttingsAirPro® Compressed AirPiping System
mm
6.0
10.0
11.5
14.0
15.0
kg
0.01
0.01
0.01
0.02
0.03
Item No.
BB.348.0020.00
BB.348.0025.00
BB.348.0032.00
BB.348.0040.00
BB.348.0050.00
daOD
s1 WeightPoids
mm
20
25
32
40
50
s2 bh s3 d
mm
14.0
16.0
16.0
17.5
20.0
mm
29
34
39
50
56
mm
6.5
6.5
6.5
6.5
6.5
mm
27.0
30.0
31.5
37.0
41.0
mm
6.5
6.5
6.5
6.5
6.5
s4
mm
9
9
9
9
9
Pipe ClipsSnap-in Type with SpacerProduct 348
Black PPGGlass Filled PolypropyleneIncludes fold-over spacer plate to allow greater clearances
Supports de tuyauType à agrafe avec entretoiseProduit 348PPG noirPolypropylène rempli de fibre de verreInclut plat d’entretoise repliable pour per-mettre de plus grands dégagements
mm
94
112
128
152
kg
0.13
0.16
0.20
0.30
Item No.
BB.049.0063.00
BB.049.0075.00
BB.049.0090.00
BB.049.0110.00
daOD
h WeightPoids
mm
63
75
90
110
d2 bz d d1
mm
30
40
40
40
mm
78
94
108
137
mm
84
82
82
82
mm
52
61
67
71
mm
53
55
57
71
Pipe ClipsRetainer TypeProduct 049
Black PPGGlass Filled PolypropyleneIncludes snap-on retainer
Supports de tuyauType ArrêtoirProduit 049PPG noirPolypropylène rempli de fibre de verreInclut arrêtoir à agrafe
Price List AP08-1 14
**Indicates regularly stocked items.Consult Chemline Plastics for availability.Subject to change without notice.
pipe clipsAirPro® Compressed AirPiping System
mm
10
11
11
Item No.
CLIP.0020.B
CLIP.0025.B
CLIP.0032.B
daOD
d1
mm
20
25
32
d2 hb h1 h2
mm
34
35
44
mm
11
12
11
Carton Quantity
20
20
20
mm
32
41
49
mm
25
26
30
t
mm
16
17
16
Pipe ClipsLow Cost Snap-in TypeProduct – CLIP
Grey PP*
Supports de tuyauType prix reduit à clicProduit – CLIPPP Gris*
* Also available in black HDPE (high density polyethylene). Change B to PE in item number. * Aussi disponible en PE (polyethylène noir. Changez B à PE dans le numero de produit.
mm
7
7
9
9
9
9
Item No.
CLIP.0040.B
CLIP.0050.B
CLIP.0063.B
CLIP.0075.B
CLIP.0090.B
CLIP.0110.B
daOD
d1
mm
40
50
63
75
90
110
d2 Hb h k
mm
68
77
94
107
124
146
mm
58
69
84
126
143
163
Carton Quantity
10
10
10
10
10
10
mm
25
25
25
30
30
30
s
mm
8
8
8
10
10
10
t
mm
–
–
–
109
125
145
z
mm
1
1
1
3
3
3
Pipe ClipsLow Cost Retainer TypeProduct – CLIP
Grey PP*Includes snap-on PVC retainer
Supports de tuyauÀ Bas Prix avec RetenueProduit – CLIPPP Gris*Retenue de PVC “snap-in” inclus
* Also available in black HDPE (high density polyethylene). Change B to PE in item number. * Aussi disponible en PE (polyethylène noir. Changez B à PE dans le numero de produit.
mm
43
47
57
64
73
85
mm
5.0
5.5
5.5
mm
14.5
14.5
17.5
17.5
17.5
17.5
kg
0.190
0.225
0.300
WeightPoids
kg
0.30
0.38
0.52
0.94
1.23
1.52
WeightPoids
Price List AP08-1 15
pipe clipsAirPro® Compressed AirPiping System
55 Guardsman Road, Thornhill, ON, L3T 6L2, Canada | ISO 9001:2008 Certified tel.905.889.7890 | fax.905.889.8553 | [email protected] | chemline.com