Air Individual State Permit 03700381-101 for McNamara Contracting,
Inc.Permittee: McNamara Contracting, Inc.
Facility name: McNamara Contracting, Inc. 16387 Chippendale Ave W
Rosemount, MN 55068 Dakota County
Expiration date: Non-expiring* * All Title I Conditions do not
expire State Permit: June 1, 2017 Permit characteristics: State;
Limits to avoid Part 70/ Limits to avoid NSR; Limits to avoid NSR
The emission units, control equipment and emission stacks at the
stationary source authorized in this permit are as described in the
Permit Applications Table. This permit authorizes the Permittee to
construct and operate the stationary source at the address listed
above unless otherwise noted in the permit. The Permittee must
comply with all the conditions of the permit. Any changes or
modifications to the stationary source must be performed in
compliance with Minn. R. 7007.1150 to 7007.1500. Terms used in the
permit are as defined in the state air pollution control rules
unless the term is explicitly defined in the permit. Unless
otherwise indicated, all the Minnesota rules cited as the origin of
the permit terms are incorporated into the SIP under 40 CFR §
52.1220 and as such as are enforceable by EPA Administrator or
citizens under the Clean Air Act.
Signature: Carolina Espejel-Schutt This document has been
electronically signed. for the Minnesota Pollution Control
Agency
for Don Smith, P.E., Manager Air Quality Permits Section Industrial
Division
Table of Contents
Page
1. Permit applications table
.............................................................................................................................................
3 2. Where to send submittals
............................................................................................................................................
4 3. Facility description
.......................................................................................................................................................
5 4. Summary of subject items
...........................................................................................................................................
6 5. Limits and other requirements
....................................................................................................................................
9 6. Submittal/action requirements
.................................................................................................................................
41 7. Appendices
.................................................................................................................................................................
57
Appendix A. Insignificant Activities and General Applicable
Requirements
............................................................ 57
Appendix B. Tank Farm Units Authorized for Construction and
Operation
............................................................ 58
Appendix C. Aggregate and HMA Processing Equipment Inventory
.......................................................................
59 Appendix D. Fugitive Dust Worksheet
.....................................................................................................................
62
Permit issued: June 1, 2017 Permit No. 03700381-101 Permit expires:
Non-expiring Page 3 of 62
1. Permit applications table
Subsequent permit applications: Title description Application
receipt date Action number State Permit 6/28/2016
03700381-101
Permit issued: June 1, 2017 Permit No. 03700381-101 Permit expires:
Non-expiring Page 4 of 62
2. Where to send submittals
Send submittals that are required to be submitted to the U.S. EPA
regional office to: Chief Air Enforcement Air and Radiation Branch
EPA Region V 77 West Jackson Boulevard Chicago, Illinois
60604
Each submittal must be postmarked or received by the date specified
in the applicable Table. Those submittals required by Minn. R.
7007.0100 to 7007.1850 must be certified by a responsible official,
defined in Minn. R. 7007.0100, subp. 21. Other submittals shall be
certified as appropriate if certification is required by an
applicable rule or permit condition.
Send submittals that are required by the Acid Rain Program
to:
U.S. Environmental Protection Agency Clean Air Markets Division
1200 Pennsylvania Avenue NW (6204N) Washington, D.C. 20460
Send any application for a permit or permit amendment to:
Fiscal Services – 6th Floor Minnesota Pollution Control Agency 520
Lafayette Road North St. Paul, Minnesota 55155-4194
Also, where required by an applicable rule or permit condition,
send to the Permit Document Coordinator notices of:
a. Accumulated insignificant activities b. Installation of control
equipment c. Replacement of an emissions unit, and d. Changes that
contravene a permit term
Unless another person is identified in the applicable Table, send
all other submittals to:
AQ Compliance Tracking Coordinator Industrial Division Minnesota
Pollution Control Agency 520 Lafayette Road North St. Paul,
Minnesota 55155-4194
Or Email a signed and scanned PDF copy to:
[email protected] (for submittals related to stack
testing)
[email protected] (for other compliance
submittals) (See complete email instructions in “Routine Air Report
Instructions Letter” at http://www.pca.state.mn.us/nwqh472.)
3. Facility description
The McNamara Contracting, Inc. (Facility) is located at 16387
Chippendale Ave W in Rosemount, MN, Dakota County, Minnesota. The
facility is a manufacturer of hot mix asphalt (HMA) and
non-metallic crushed aggregate used in construction applications.
While McNamara currently operates portable HMA and aggregate
operations under separate permits, this permit will cover the HMA
and aggregate operations as a stationary source at the permitted
address located in Empire Township when operations are not being
used as portable operations. In addition to HMA and aggregate
operations, the Permittee plans to construct a tank farm where
asphalt cement (AC) will be stored and transferred in the
production of HMA. Description of permit action This permit
authorizes the operation of the HMA and non-metallic aggregate
operations described in this permit. This permit action also
authorizes construction and operation of the tank farm above and in
this permit. The tank farm project will be constructed in phases.
Phase 1 will include the construction of one 7,500-ton tank
(EQUI11), truck loading/load out rack (FUGI6), and the Tank Farm
Tank Heater #1 (EQUI6). Phase 2 includes the second 7,500- ton tank
(EQUI12), and the rail system. Phase 3 includes both of the
5,000-ton tanks (EQUI13 and EQUI14) and Phase 4 includes both of
the 100-ton PMAC tanks (EQUI15 and EQUI16), and both of the 800-ton
load out tanks (EQUI17 and EQUI18).
Permit issued: June 1, 2017 Permit No. 03700381-101 Permit expires:
Non-expiring Page 6 of 62
4. Summary of subject items
SI ID: Description
Relationshi p Type
has members
COMG2: Crushing Operations (NSPS, subpart OOO)
has members
EQUI19, EQUI20, EQUI21
COMG3: Screening and Conveyor Operations - August 31, 1983 to April
22, 2008 (NSPS, subpart OOO)
has members
EQUI23, EQUI24, EQUI25, EQUI31, EQUI32, EQUI33, EQUI34, EQUI35,
EQUI36, EQUI37, EQUI38, EQUI39, EQUI40, EQUI41, EQUI42, EQUI43,
EQUI44
COMG4: Screening and Conveyor Operations - After April 22, 2008
(NSPS, subpart OOO)
has members
EQUI19, EQUI20, EQUI21, EQUI22, EQUI23, EQUI24, EQUI25, EQUI26,
EQUI27, EQUI28, EQUI29, EQUI30, EQUI31, EQUI32, EQUI33,
SI ID: Description
Relationshi p Type
Related SI ID: Description EQUI34, EQUI35, EQUI36, EQUI37, EQUI38,
EQUI39, EQUI40, EQUI41, EQUI42, EQUI43, EQUI44, EQUI45, EQUI46,
EQUI47, EQUI48, EQUI49, EQUI50
COMG6: HMA Spread Requirements
COMG7: HMA Plant Dryer Requirements
has members
sends to STRU16: HMA Plant Liquid AC Storage Tank #3
EQUI11: Tank Farm AC Storage Tank #1 (7500 ton)
sends to STRU17: Tank Farm AC Storage Tank #1 (7500 ton)
EQUI12: Tank Farm AC Storage Tank #2 (7500 ton)
sends to STRU18: Tank Farm AC Storage Tank #2 (7500 ton)
EQUI13: Tank Farm AC Storage Tank #3 (5000 ton)
sends to STRU19: Tank Farm AC Storage Tank #3 (5000 ton)
EQUI14: Tank Farm AC Storage Tank #4 (5000 ton)
sends to STRU20: Tank Farm AC Storage Tank #4 (5000 ton)
EQUI15: Tank Farm PMAC Tank #1 (100 ton)
sends to STRU21: Tank Farm PMAC Tank #1 (100 ton)
EQUI16: Tank Farm sends to STRU22: Tank
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 7 of 62
SI ID: Description
Relationshi p Type
Related SI ID: Description
PMAC Tank #2 (100 ton) Farm PMAC Tank #2 (100 ton)
EQUI17: Tank Farm Load out Tank #1 (800 ton)
sends to STRU23: Tank Farm Load out Tank #1 (800 ton)
EQUI18: Tank Farm Load out Tank #2 (800 ton)
sends to STRU24: Tank Farm Load out Tank #2 (800 ton)
EQUI19: Pioneer Jaw Crusher
TREA1: HMA Plant Dryer Fabric Filter
EQUI20: Cedar Rapids Impact Crusher
EQUI21: Electric Cone Crusher
EQUI22: Spokane Impact Crusher
EQUI23: Screen 1 6'x20' EQUI24: Screen 2 5'x20' EQUI25: Screen 3
6'x20' EQUI26: Conveyor 3 (90')
EQUI27: Conveyor 4 (90')
EQUI2: HMA Plant Silo #1
sends to STRU8: HMA Plant Silo #1
EQUI30: Conveyor 6 (200')
EQUI31: Conveyor 7 (80')
EQUI32: Conveyor 10 (60')
EQUI33: Conveyor 11 (80')
EQUI34: Conveyor 12 (50')
EQUI35: Conveyor 14 (60')
EQUI36: Conveyor 15 (30')
EQUI37: Conveyor 16 (50')
sends to STRU9: HMA Plant Silo #2
EQUI40: Conveyor 21 (95')
EQUI41: Conveyor 23 (60')
EQUI42: Conveyor 24 (100')
EQUI43: Conveyor 25 (120')
EQUI44: Conveyor 26 (60')
EQUI45: Conveyor 27 (60')
EQUI46: Conveyor 8 (40')
EQUI47: Conveyor 9 (120')
EQUI48: Conveyor 13 (60')
EQUI49: Conveyor 18 (120')
sends to STRU10: HMA Plant Silo #3
EQUI50: Conveyor 19 (60')
sends to STRU11: HMA Plant Hot Oil Heater
EQUI6: Tank Farm Tank Heater #1
sends to STRU12: Tank Farm Tank Heater #1
EQUI7: Tank Farm Tank Heater #2
sends to STRU13: Tank Farm Tank Heater #2
EQUI8: HMA Plant Liquid AC Storage Tank #1
sends to STRU14: HMA Plant Liquid AC Storage Tank #1
EQUI9: HMA Plant Liquid AC Storage Tank #2
sends to STRU15: HMA Plant Liquid AC Storage Tank #2
FUGI1: HMA Plant Loader Traffic
FUGI2: HMA Plant Hot
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 8 of 62
SI ID: Description
Relationshi p Type
FUGI4: HMA Plant Haul Roads
FUGI5: Storage Piles FUGI6: Tank Farm Loading/Unloading Rack
FUGI7: Tank Farm Hauls Roads
STRU10: HMA Plant Silo #3
STRU11: HMA Plant Hot Oil Heater
STRU12: Tank Farm Tank Heater #1
STRU13: Tank Farm Tank Heater #2
STRU14: HMA Plant Liquid AC Storage Tank #1
STRU15: HMA Plant Liquid AC Storage Tank #2
STRU16: HMA Plant Liquid AC Storage Tank #3
STRU17: Tank Farm AC Storage Tank #1 (7500 ton)
STRU18: Tank Farm AC Storage Tank #2 (7500 ton)
STRU19: Tank Farm AC Storage Tank #3 (5000
SI ID: Description
Relationshi p Type
STRU20: Tank Farm AC Storage Tank #4 (5000 ton)
STRU21: Tank Farm PMAC Tank #1 (100 ton)
STRU22: Tank Farm PMAC Tank #2 (100 ton)
STRU23: Tank Farm Load out Tank #1 (800 ton)
STRU24: Tank Farm Load out Tank #2 (800 ton)
STRU2: HMA Plant Baghouse
STRU3: HMA Plant Office
STRU5: Loading Rack/Truck Unloading
receives from
TFAC1: McNamara Contracting, Inc.
TREA1: HMA Plant Dryer Fabric Filter
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 9 of 62
5. Limits and other requirements
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
TFAC1 McNamara
Contracting, Inc.
5.1.1 Permit Appendices: This permit contains appendices as listed
in the permit Table of Contents. The Permittee shall comply with
all requirements contained in the following appendices: Appendix A
(Insignificant Activities and General Applicable Requirements);
Appendix B (Tank Farm Units Authorized for Construction and
Operation); Appendix C (HMA and Aggregate Processing Equipment
Inventory); and Appendix D (Fugitive Dust Worksheet). [Minn. R.
7007.0800, subp. 2]
5.1.2 Labeling Requirements: Permanently affix the manufacturer's
serial number (or otherwise unique identifying number) to each
piece of aggregate processing equipment (crushing, screening, and
conveying) and HMA production equipment (dryer, silos, and tanks)
described in COMG5 and COMG6 within 60 days of permit issuance. The
number shall be permanently affixed and maintained so that it is
readable and visible at all times from a safe distance at each
stationary source. This number shall correspond to the EQUI number
contained in the equipment inventory (Appendix C). [Minn. R.
7007.0800, subp. 2]
5.1.3 Equipment Inventory List: The Permittee shall maintain a
written list of each emission unit on site. This list shall include
a description of the emission unit, unique ID number (assigned and
affixed as required by this permit), equipment capacity,
construction date, and NSPS subp. OOO applicability. The list shall
correlate the units to the numbers used in this permit (EQUI, COMG)
and shall include the data in Appendix C. The date of construction
shall be the date the piece of equipment was manufactured or
otherwise modified or reconstructed. [Minn. R. 7007.0800, subp.
2]
5.1.4 Equipment Inventory List Updates: The Permittee shall update
the equipment inventory list whenever a new piece of equipment is
brought on-site, a piece of equipment leaves the site, or a piece
of existing equipment is modified. These updates to the equipment
inventory list shall take place by the end of the business day in
which the change occurred or otherwise as soon as practicable.
[Minn. R. 7007.0800, subp. 2]
5.1.5 Visible Emissions Check: The Permittee shall check visible
emissions once daily when in operation during daylight hours using
the visible emissions checklists for all sources included in
Appendix D. If, based on completion of the checklist, the Permittee
determines that additional investigative or remedial action is
required; the Permittee shall investigate process and control
equipment, and, if necessary, implement appropriate corrective
action. [Minn. R.
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 10 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
7007.0800, 16(J), Minn. R. 7007.0800, 4(D), Minn. R. 7007.0800,
subp. 14]
5.1.6 The Permittee shall keep records of fugitive emissions
control measures taken by the facility for a minimum of five years.
This includes, but is not limited to, visible emission checks, wind
events that delay operations and training records. [Minn. R.
7007.0800, subp. 5]
5.1.7 The Permittee shall report the dates when fugitive dust is
visible in a semiannual report to the Agency. The report shall also
identify any fugitive emissions corrective actions taken by the
facility. [Minn. R. 7007.0800, subp. 6]
5.1.8 PERMIT SHIELD: Subject to the limitations in Minn. R.
7007.1800, compliance with the conditions of this permit shall be
deemed compliance with the specific provision of the applicable
requirement identified in the permit as the basis of each
condition. Subject to the limitations of Minn. R. 7007.1800 and
7017.0100, subp. 2, notwithstanding the conditions of this permit
specifying compliance practices for applicable requirements, any
person (including the Permittee) may also use other credible
evidence to establish compliance or noncompliance with applicable
requirements. This permit shall not alter or affect the liability
of the Permittee for any violation of applicable requirements prior
to or at the time of permit issuance. [Minn. R. 7007.1800,
(A)(2)]
5.1.9 Circumvention: Do not install or use a device or means that
conceals or dilutes emissions, which would otherwise violate a
federal or state air pollution control rule, without reducing the
total amount of pollutant emitted. [Minn. R. 7011.0020]
5.1.10 Air Pollution Control Equipment: Operate all pollution
control equipment whenever the corresponding process equipment and
emission units are operated. [Minn. R. 7007.0800, subp. 16(J),
Minn. R. 7007.0800, subp. 2]
5.1.11 Operation and Maintenance Plan: Retain at the stationary
source an operation and maintenance plan for all air pollution
control equipment. At a minimum, the O & M plan shall identify
all air pollution control equipment and control practices and shall
include a preventative maintenance program for the equipment and
practices, a description of (the minimum but not necessarily the
only) corrective actions to be taken to restore the equipment and
practices to proper operation to meet applicable permit conditions,
a description of the employee training program for proper operation
and maintenance of the control equipment and practices, and the
records kept to demonstrate plan implementation. [Minn. R.
7007.0800, subp. 14, Minn. R. 7007.0800, subp. 16(J)]
5.1.12 Operation Changes: In any shutdown, breakdown, or deviation
the Permittee shall immediately take all practical steps to modify
operations to reduce the emission of any regulated air pollutant.
The Commissioner may require feasible and practical modifications
in the operation to reduce emissions of air pollutants. No
emissions
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 11 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
units that have an unreasonable shutdown or breakdown frequency of
process or control equipment shall be permitted to operate. [Minn.
R. 7019.1000, subp. 4]
5.1.13 Fugitive Emissions: Do not cause or permit the handling,
use, transporting, or storage of any material in a manner which may
allow avoidable amounts of particulate matter to become airborne.
Comply with all other requirements listed in Minn. R. 7011.0150.
[Minn. R. 7011.0150]
5.1.14 Noise: The Permittee shall comply with the noise standards
set forth in Minn. R. 7030.0010 to 7030.0080 at all times during
the operation of any emission units. This is a state only
requirement and is not enforceable by the EPA Administrator or
citizens under the Clean Air Act. [Minn. R.
7030.0010-7030.0080]
5.1.15 Inspections: The Permittee shall comply with the inspection
procedures and requirements as found in Minn. R. 7007.0800, subp.
9(A). [Minn. R. 7007.0800, subp. 9(A)]
5.1.16 The Permittee shall comply with the General Conditions
listed in Minn. R. 7007.0800, subp. 16. [Minn. R. 7007.0800, subp.
16]
5.1.17 Performance Testing: Conduct all performance tests in
accordance with Minn. R. ch. 7017 unless otherwise noted in this
permit. [Minn. R. ch. 7017]
5.1.18 Performance Test Notifications and Submittals: Performance
Test Notification and Plan: due 30 days before each Performance
Test Performance Test Pre-test Meeting: due 7 days before each
Performance Test Performance Test Report: due 45 days after each
Performance Test The Notification, Test Plan, and Test Report must
be submitted in a format specified by the commissioner. [Minn. R.
7017.2017, Minn. R. 7017.2030, subps. 1-4, Minn. R. 7017.2035,
subps. 1-2]
5.1.19 Limits set as a result of a performance test (conducted
before or after permit issuance) apply until superseded as stated
in the MPCA's Notice of Compliance letter granting preliminary
approval. Preliminary approval is based on formal review of a
subsequent performance test on the same unit as specified by Minn.
R. 7017.2025, subp. 3. The limit is final upon issuance of a permit
amendment incorporating the change. [Minn. R. 7017.2025, subp.
3]
5.1.20 Monitoring Equipment Calibration - The Permittee shall
either: 1. Calibrate or replace required monitoring equipment every
12 months; or 2. Calibrate at the frequency stated in the
manufacturer's specifications. For each monitor, the Permittee
shall maintain a record of all calibrations, including the date
conducted, and any corrective action that resulted. The Permittee
shall include the calibration frequencies, procedures, and
manufacturer's specifications (if applicable) in the Operations and
Maintenance Plan. Any
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 12 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
requirements applying to continuous emission monitors are listed
separately in this permit. [Minn. R. 7007.0800, subp. 4(D)]
5.1.21 Operation of Monitoring Equipment: Unless noted elsewhere in
this permit, monitoring a process or control equipment connected to
that process is not necessary during periods when the process is
shutdown, or during checks of the monitoring systems, such as
calibration checks and zero and span adjustments. If monitoring
records are required, they should reflect any such periods of
process shutdown or checks of the monitoring system. [Minn. R.
7007.0800, subp. 4(D)]
5.1.22 Recordkeeping: Retain all records at the stationary source,
unless otherwise specified within this permit, for a period of five
(5) years from the date of monitoring, sample, measurement, or
report. Records which must be retained at this location include all
calibration and maintenance records, all original recordings for
continuous monitoring instrumentation, and copies of all reports
required by the permit. Records must conform to the requirements
listed in Minn. R. 7007.0800, subp. 5(A). [Minn. R. 7007.0800,
subp. 5(C)]
5.1.23 Recordkeeping: Maintain records describing any insignificant
modifications (as required by Minn. R. 7007.1250, subp. 3) or
changes contravening permit terms (as required by Minn. R.
7007.1350, subp. 2), including records of the emissions resulting
from those changes. [Minn. R. 7007.0800, subp. 5(B)]
5.1.24 Shutdown Notifications: Notify the Commissioner at least 24
hours in advance of a planned shutdown of any control equipment or
process equipment if the shutdown would cause any increase in the
emissions of any regulated air pollutant. If the owner or operator
does not have advance knowledge of the shutdown, notification shall
be made to the Commissioner as soon as possible after the shutdown.
However, notification is not required in the circumstances outlined
in Items A, B and C of Minn. R. 7019.1000, subp. 3. At the time of
notification, the owner or operator shall inform the Commissioner
of the cause of the shutdown and the estimated duration. The owner
or operator shall notify the Commissioner when the shutdown is
over. [Minn. R. 7019.1000, subp. 3]
5.1.25 Breakdown Notifications: Notify the Commissioner within 24
hours of a breakdown of more than one-hour duration of any control
equipment or process equipment if the breakdown causes any increase
in the emissions of any regulated air pollutant. The 24- hour time
period starts when the breakdown was discovered or reasonably
should have been discovered by the owner or operator. However,
notification is not required in the circumstances outlined in Items
A, B and C of Minn. R. 7019.1000, subp. 2. At the time of
notification or as soon as possible thereafter, the owner or
operator shall inform the Commissioner of the cause of the
breakdown and the estimated duration. The owner or operator
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 13 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
shall notify the Commissioner when the breakdown is over. [Minn. R.
7019.1000, subp. 2]
5.1.26 Notification of Deviations Endangering Human Health or the
Environment: As soon as possible after discovery, notify the
Commissioner or the state duty officer, either orally or by
facsimile, of any deviation from permit conditions which could
endanger human health or the environment. [Minn. R. 7019.1000,
subp. 1]
5.1.27 Notification of Deviations Endangering Human Health or the
Environment Report: Within 2 working days of discovery, notify the
Commissioner in writing of any deviation from permit conditions
which could endanger human health or the environment. Include the
following information in this written description: 1. the cause of
the deviation; 2. the exact dates of the period of the deviation,
if the deviation has been corrected; 3. whether or not the
deviation has been corrected; 4. the anticipated time by which the
deviation is expected to be corrected, if not yet corrected; and 5.
steps taken or planned to reduce, eliminate, and prevent
reoccurrence of the deviation. [Minn. R. 7019.1000, subp. 1]
5.1.28 Application for Permit Amendment: If a permit amendment is
needed, submit an application in accordance with the requirements
of Minn. R. 7007.1150 through Minn. R. 7007.1500. Submittal dates
vary, depending on the type of amendment needed. Upon adoption of a
new or amended federal applicable requirement, and if there are
more than 3 years remaining in the permit term, the Permittee shall
file an application for an amendment within nine months of
promulgation of the applicable requirement, pursuant to Minn. R.
7007.0400, subp. 3. [Minn. R. 7007.0400, subp. 3, Minn. R.
7007.1150 - 7007.1500]
5.1.29 If the Permittee determines that no permit amendment or
notification is required prior to making a change, the Permittee
must retain records of all calculations required under Minn. R.
7007.1200. These records shall be kept for a period of five years
from the date the change was made. The records shall be kept at the
stationary source for the current calendar year of operation and
may be kept at the stationary source or office of the stationary
source for all other years. The records may be maintained in either
electronic or paper format. [Minn. R. 7007.1200, subp. 4]
5.1.30 Extension Requests: The Permittee may apply for an
Administrative Amendment to extend a deadline in a permit by no
more than 120 days, provided the proposed deadline extension meets
the requirements of Minn. R. 7007.1400, subp. 1(H). Performance
testing deadlines from the General Provisions of 40 CFR pt. 60 and
pt. 63 are examples of deadlines for which the MPCA does not have
authority to grant extensions and therefore do not meet the
requirements of Minn. R. 7007.1400, subp. 1(H). [Minn. R.
7007.1400, subp. 1(H)]
5.1.31 Emission Inventory Report: due on or before April 1 of
each
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 14 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
calendar year following permit issuance, to be submitted on a form
approved by the Commissioner. [Minn. R. 7019.3000-7019.3100]
5.1.32 Emission Fees: due 30 days after receipt of an MPCA bill.
[Minn. R. 7002.0005-7002.0095]
COMG1 GP001 Asphalt Cement
Tanks (Tank Farm)
5.2.1 The Permittee shall limit the receiving of Asphalt Cement
<= 12 million gallons per year 12-month rolling sum as defined
in Minn. R. 7007.0100, subp. 21a. [Minn. R. 7007.0800, subp.
2]
5.2.2 Daily Recordkeeping: On each day of operation at the
stationary source, the Permittee shall record and maintain a record
of the total quantity of asphalt cement received. [Minn. R.
7007.0800, subp. 2]
5.2.3 Monthly Recordkeeping: Asphalt Cement Receiving By the 15th
day of each month, the Permittee shall calculate and record the
following: 1) The sum of asphalt cement received in all units in
COMG1 for the previous month; and 2) The 12-month rolling sum
combined receiving of asphalt cement for the previous 12-month
period for COMG1. [Minn. R. 7007.0800, subp. 2]
COMG2 GP002 Crushing
Operations (NSPS, subpart OOO)
5.3.1 The Permittee shall limit Opacity <= 15 percent opacity.
This limit applies to crushing equipment that is subject to the
NSPS, subp. OOO limit that applies to affected facilities
constructed, reconstructed or modified on or after August 31, 1983
and before April 22, 2008. This limit applies within 60 days after
achieving the maximum production rate at which the unit will be
operated, but not later than 180 days after initial startup as
required under 40 CFR Section 60.11. [40 CFR 60.672(b), 40 CFR pt.
60, subp. OOO, Table 3, Minn. R. 7011.3350]
5.3.2 The Permittee shall limit Opacity <= 12 percent opacity.
This limit applies to crushing equipment that is subject to the
NSPS, subp. OOO limit that applies to affected facilities
constructed, reconstructed or modified on or after April 22, 2008.
This limit applies within 60 days after achieving the maximum
production rate at which the unit will be operated, but not later
than 180 days after initial startup as required under 40 CFR
Section 60.11. [40 CFR 60.672(b), 40 CFR pt. 60, subp. OOO, Table
3, Minn.
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 15 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
R. 7011.3350]
5.3.3 The Permittee shall submit a notification of any physical or
operational change which increases emission rate: due 60 days (or
as soon as practical) before the change is commenced. [40 CFR
60.7(a)(4), Minn. R. 7019.0100, subp. 1]
5.3.4 Recordkeeping: The Permittee shall maintain records of the
occurrence and duration of any startup, shutdown, or malfunction in
the operation of the facility including; any malfunction of the air
pollution control equipment; or any periods during which a
continuous monitoring system or monitoring device is inoperative.
[40 CFR 60.7(b), Minn. R. 7019.0100, subp. 1]
5.3.5 Recordkeeping: The Permittee shall maintain a file of all
measurements, maintenance, reports and records for at least five
years. This requirement is more stringent than 40 CFR Section
60.7(f), which specifies two years. [40 CFR 60.7(f), Minn. R.
7007.0800, subp. 5(C), Minn. R. 7019.0100, subp. 1]
5.3.6 Opacity Compliance: The Permittee shall demonstrate
compliance with opacity standards using Reference Method 9. [40 CFR
60.11, Minn. R. 7017.2015]
5.3.7 No owner or operator shall build, erect, install, or use any
article, machine, equipment or process, the use of which conceals
an emission which would otherwise constitute a violation of an
applicable standard. [40 CFR 60.12, Minn. R. 7011.0050]
COMG3 GP003 Screening and
Conveyor Operations - August 31, 1983 to April 22, 2008 (NSPS,
subpart OOO)
5.4.1 The Permittee shall limit Opacity <= 10 percent opacity.
This limit applies to screening and belt conveyor equipment that
are subject to the NSPS, subp. OOO limit that applies to affected
facilities constructed, reconstructed or modified on or after
August 31, 1983 and before April 22, 2008. This limit applies
within 60 days after achieving the maximum production rate at which
the unit will be operated, but not later than 180 days after
initial startup as required under 40 CFR Section 60.11. [40 CFR
60.672(b), Minn. R. 7011.3350]
5.4.2 The Permittee shall submit a notification of any physical or
operational change which increases emission rate: due 60 days (or
as soon as practical) before the change is commenced. [40 CFR
60.7(a)(4), Minn. R. 7019.0100, subp. 1]
5.4.3 Recordkeeping: The Permittee shall maintain records of the
occurrence and duration of any startup, shutdown, or malfunction in
the operation of the facility including; any malfunction of the air
pollution control equipment; or any periods during which a
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 16 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
continuous monitoring system or monitoring device is inoperative.
[40 CFR 60.7(b), Minn. R. 7019.0100, subp. 1]
5.4.4 Recordkeeping: The Permittee shall maintain a file of all
measurements, maintenance, reports and records for at least five
years. This requirement is more stringent than 40 CFR Section
60.7(f), which specifies two years. [40 CFR 60.7(f), Minn. R.
7007.0800, subp. 5(C), Minn. R. 7019.0100, subp. 1]
5.4.5 Opacity Compliance: The Permittee shall demonstrate
compliance with opacity standards using Reference Method 9. [40 CFR
60.11, Minn. R. 7017.2015]
5.4.6 No owner or operator shall build, erect, install, or use any
article, machine, equipment or process, the use of which conceals
an emission which would otherwise constitute a violation of an
applicable standard. [40 CFR 60.12, Minn. R. 7011.0050]
COMG4 GP004 Screening and
Conveyor Operations - After April 22, 2008 (NSPS, subpart
OOO)
5.5.1 The Permittee shall limit Opacity <= 7 percent opacity.
This limit applies to screening and conveyor equipment that is
subject to the NSPS, subp. OOO limit that applies to affected
facilities constructed, reconstructed or modified on or after April
22, 2008. This limit applies within 60 days after achieving the
maximum production rate at which the unit will be operated, but not
later than 180 days after initial startup as required under 40 CFR
Section 60.11. [40 CFR 60.672(b), Minn. R. 7011.3350]
5.5.2 The Permittee shall submit a notification of any physical or
operational change which increases emission rate: due 60 days (or
as soon as practical) before the change is commenced. [40 CFR
60.7(a)(4), Minn. R. 7019.0100, subp. 1]
5.5.3 Recordkeeping: The Permittee shall maintain records of the
occurrence and duration of any startup, shutdown, or malfunction in
the operation of the facility including; any malfunction of the air
pollution control equipment; or any periods during which a
continuous monitoring system or monitoring device is inoperative.
[40 CFR 60.7(b), Minn. R. 7019.0100, subp. 1]
5.5.4 Recordkeeping: The Permittee shall maintain a file of all
measurements, maintenance, reports and records for at least five
years. This requirement is more stringent than 40 CFR Section
60.7(f), which specifies two years. [40 CFR 60.7(f), Minn. R.
7007.0800, subp. 5(C), Minn. R. 7019.0100, subp. 1]
5.5.5 Opacity Compliance: The Permittee shall demonstrate
compliance with opacity standards using Reference Method 9. [40 CFR
60.11, Minn. R. 7017.2015]
5.5.6 No owner or operator shall build, erect, install, or use any
article,
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 17 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
machine, equipment or process, the use of which conceals an
emission which would otherwise constitute a violation of an
applicable standard. [40 CFR 60.12, Minn. R. 7011.0050]
COMG5 GP005 Aggregate
Spread Requirements
5.6.1 The Permittee shall limit Feed Material Moisture Content
>= 1.5 percent. [To avoid major source under 40 CFR 70.2 &
Minn. R. 7007.0200]
5.6.2 Feed Material Moisture Content Compliance Demonstration: The
Permittee shall demonstrate the feed material moisture content is
greater than or equal to 1.5 percent by either of the following
options: Option 1: Test moisture content of each different feed
material source (sampled at an area representative of the feed
source and physically capable of being sampled), as follows: a. Use
ASTM method numbers D 2216-92 or D 4643-93 (or equivalent); b. If
the temperature is less than 35 degree F (1.7C), as measured at the
facility during daylight operating hours, then moisture testing is
not required; c. Keep records of each moisture content test
summarizing the method used, results, date, time, and initials of
person performing test; d. Test weekly, when operating, unless
three consecutive tests at the stationary source location show
moisture contents of greater than or equal to 1.5 percent after
which testing is no longer required until the source of the feed
material changes; and e. When testing indicates that feed material
moisture content is less than 1.5 percent, or in situations where
it is infeasible to sample and test, or where the Permittee elects
not to sample and test, the Permittee shall operate a moisture
addition device at or immediately prior to the initial crusher(s)
or initial screen(s) where unprocessed feed material is being fed
to achieve a moisture content greater than or equal to 1.5 percent.
Moisture addition during operation shall continue until subsequent
moisture content testing demonstrates that feed material moisture
content is greater than or equal to 1.5 percent. When testing
indicates that feed material moisture content is less than 1.5
percent and the Permittee is operating a moisture addition device,
daily, when operating, either: (i) Keep records of the date, water
flow rate, material throughput rate, and initials of the person
making the record and the time the record was made; or (ii) Conduct
moisture content testing weekly on the feed material after water
application following a., b., and c. above, and if results show
moisture content is less than 1.5 percent, increase water addition
to insure moisture is 1.5 percent or greater and re-test to
verify.
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 18 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
OR Option 2: Keep records indicating instances when feed material
was sourced from or is being removed from below the water table or
wet processed prior to arriving at the site. Records shall include
a description of the source, the corresponding dates, and the
initials of the person making the record. [To avoid major source
under 40 CFR 70.2 & Minn. R. 7007.0200]
5.6.3 Aggregate Processing Spread Definition: The aggregate
processing spread shall consist of the following units with total
capacities at any one time not to exceed the following: aggregate
crushers (impact, cone, jaw, etc.) with a combined capacity of
1,300 tons/hr, aggregate screens with a combined capacity of 1,600
tons/hr and aggregate conveyors with combined capacity of 7,800
tons/hr. For the purposes of this permit, the main aggregate
processing spread is defined as the group of crushing, screening
and conveying equipment that are used for non-metallic mineral
processing. This requirement does not prohibit equipment from being
installed outside of the spread definition described here.
Equipment may be installed outside of the spread definition and
shall be evaluated for the appropriate permit amendment as
described under Minn. R. 7007.1150-1500 and elsewhere in this
permit. [Minn. R. 7007.0800, subp. 2, To avoid major source under
40 CFR 70.2 & Minn. R. 7007.0200]
5.6.4 Aggregate Equipment Capacity Compliance Demonstration: The
Permittee shall demonstrate compliance with the above aggregate
spread capacity limits by keeping up-to-date records and other
documentation on-site as described in TFAC1. The equipment
inventory list shall be updated to accurately reflect what
equipment is on-site at any given time and shall contain, at a
minimum, the equipment information shown in Appendix C. [Minn. R.
7007.0800, subp. 2, To avoid major source under 40 CFR 70.2 &
Minn. R. 7007.0200]
5.6.5 Aggregate Spread Component Replacement: The Permittee may
replace aggregate processing equipment or modify existing equipment
without obtaining a permit amendment provided the new total
equipment capacity after the modification does not exceed that
which is listed in this permit (e.g. the replacement of a crusher
does not bring the total facility crushing capacity above 1,300
tons/hr). If the Permittee replaces any of the aggregate processing
equipment or modifies the existing equipment, such equipment is
subject to all applicable permit limits as well as all of the
requirements of one or more of the following groups: COMG2, COMG3
or COMG4. The applicability of COMG2, COMG3 or COMG4 is determined
by the construction, reconstruction or modification date of the
equipment. A permit amendment will still be needed regardless of
the emissions increase if the change will be subject to a new
applicable
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 19 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
requirement or requires revisions to the limits or monitoring and
recordkeeping in this permit. Prior to making such a change, the
Permittee shall apply for and obtain the appropriate permit
amendment, as applicable. [To avoid major source under 40 CFR 70.2
& Minn. R. 7007.0200]
5.6.6 When an opacity compliance demonstration is required for a
replacement unit, the replacement unit shall demonstrate compliance
with the opacity limits within 60 days after achieving the maximum
production rate of the unit, but not later than 180 days after
initial startup. [40 CFR 60.11(e)(1), 40 CFR pt. 60, subp. OOO,
Table 3, Minn. R. 7011.3350]
5.6.7 Performance Tests Conducted Off-Site (NSPS, subp. OOO): If
applicable performance tests are conducted at a location other than
this stationary source for units subject to NSPS, subp. OOO, the
Permittee may provide these performance test results to the
Commissioner as demonstration of compliance for the initial
performance test required at the stationary source. Performance
tests conducted off-site that are used to meet the initial
performance test requirements of this stationary source shall meet
all performance test criteria specified in this permit. The
Permittee shall keep copies of these records at the stationary
source for no fewer than five (5) years. [Minn. R. 7007.0800, subp.
5, Minn. R. 7017.2020]
5.6.8 The Permittee shall submit a notification of any physical or
operational change which increases emission rate: due 60 days (or
as soon as practical) before the change is commenced. [40 CFR
60.7(a)(4), Minn. R. 7019.0100, subp. 1]
5.6.9 Recordkeeping: The Permittee shall maintain records of the
occurrence and duration of any startup, shutdown, or malfunction in
the operation of the facility including; any malfunction of the air
pollution control equipment; or any periods during which a
continuous monitoring system or monitoring device is inoperative.
[40 CFR 60.7(b), Minn. R. 7019.0100, subp. 1]
5.6.10 Recordkeeping: The Permittee shall maintain a file of all
measurements, maintenance, reports and records for at least five
years. This requirement is more stringent than 40 CFR Section
60.7(f), which specifies two years. [40 CFR 60.7(f), Minn. R.
7007.0800, subp. 5(C), Minn. R. 7019.0100, subp. 1]
5.6.11 Opacity Compliance: The Permittee shall demonstrate
compliance with opacity standards using Reference Method 9. [40 CFR
60.11, Minn. R. 7017.2015]
5.6.12 No owner or operator shall build, erect, install, or use any
article, machine, equipment or process, the use of which conceals
an emission which would otherwise constitute a violation of an
applicable standard. [40 CFR 60.12, Minn. R. 7011.0050]
COMG6 GP006 HMA Spread
5.7.1 Hot Mix Asphalt (HMA) Spread Definition:
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 20 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
The HMA spread shall consist of the following units with total
capacities at any one time not to exceed the following: a HMA plant
dryer with a maximum burner capacity of 234 MMBtu/hr, asphalt
cement storage tanks with a combined capacity of 80,000 gallons,
HMA plant silos with a combined capacity of 3,000 tons and HMA load
out with a capacity of 600 tons/hr. This requirement does not
prohibit equipment from being installed outside of the spread
definition described here. Equipment may be installed outside of
the spread definition and shall be evaluated for the appropriate
permit amendment as described under Minn. R. 7007.1150-1500 and
elsewhere in this permit. [Minn. R. 7007.0800, subp. 2, To avoid
major source under 40 CFR 70.2 & Minn. R. 7007.0200]
5.7.2 HMA Equipment Capacity Compliance Demonstration: The
Permittee shall demonstrate compliance with the above HMA spread
capacity limits by keeping up-to-date records and other
documentation on-site as described in TFAC1. The equipment
inventory list shall be updated to accurately reflect what
equipment is on-site at any given time and shall contain, at a
minimum, the equipment information shown in Appendix C. [Minn. R.
7007.0800, subp. 2, To avoid major source under 40 CFR 70.2 &
Minn. R. 7007.0200]
5.7.3 HMA Spread Component Replacement: The Permittee may replace
HMA production equipment or modify existing equipment without
obtaining a permit amendment provided the new total equipment
capacity after the modification does not exceed that which is
listed in this permit (e.g. the total burner capacity of the HMA
dryer does not exceed 234 MMBtu/hr after the modification). If the
Permittee replaces any of the HMA production equipment or modifies
the existing equipment, such equipment is subject to all applicable
limits and requirements specified in this permit. A permit
amendment will still be needed regardless of the emissions increase
if the change will be subject to a new applicable requirement or
requires revisions to the limits or monitoring and recordkeeping in
this permit. Prior to making such a change, the Permittee shall
apply for and obtain the appropriate permit amendment, as
applicable. [To avoid major source under 40 CFR 70.2 & Minn. R.
7007.0200]. [To avoid major source under 40 CFR 70.2 & Minn. R.
7007.0200]
5.7.4 When an opacity compliance demonstration is required for a
replacement unit, the replacement unit shall demonstrate compliance
with the opacity limits within 60 days after achieving the maximum
production rate of the unit, but not later than 180 days after
initial startup. [40 CFR 60.11(e)(1), Minn. R. 7011.3350]
5.7.5 The Permittee shall submit a notification of any physical or
operational change which increases emission rate: due 60 days (or
as soon as practical) before the change is commenced. [40 CFR
60.7(a)(4), Minn. R. 7019.0100, subp. 1]
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 21 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
5.7.6 Recordkeeping: The Permittee shall maintain records of
the
occurrence and duration of any startup, shutdown, or malfunction in
the operation of the facility including; any malfunction of the air
pollution control equipment; or any periods during which a
continuous monitoring system or monitoring device is inoperative.
[40 CFR 60.7(b), Minn. R. 7019.0100, subp. 1]
5.7.7 Recordkeeping: The Permittee shall maintain a file of all
measurements, maintenance, reports and records for at least five
years. This requirement is more stringent than 40 CFR Section
60.7(f), which specifies two years. [40 CFR 60.7(f), Minn. R.
7007.0800, subp. 5(C), Minn. R. 7019.0100, subp. 1]
5.7.8 Opacity Compliance: The Permittee shall demonstrate
compliance with opacity standards using Reference Method 9. [40 CFR
60.11, Minn. R. 7017.2015]
5.7.9 No owner or operator shall build, erect, install, or use any
article, machine, equipment or process, the use of which conceals
an emission which would otherwise constitute a violation of an
applicable standard. [40 CFR 60.12, Minn. R. 7011.0050]
COMG7 GP007 HMA Plant Dryer
Requirements
5.8.1 The requirements of COMG7 apply to any current, new, or
replacement HMA dryer(s) at the facility and are subject to all
limitations, notifications, and recordkeeping requirements in this
group. If the Permittee replaces the dryer as allowed under the
precap (COMG6), the new dryer shall be subject to the requirements
in COMG7. The Permittee may construct and operate additional dryers
beyond what is allowed under the precap provided the project avoids
applicable emissions thresholds (PSD and Part 70). The Permittee
shall evaluate such projects following amendment procedures
described under Minn. R. 7007.1150- 7007.1500. [Minn. R. 7007.0800,
subp 2, Title I Condition: Avoid major source under 40 CFR
52.21(b)(1)& Minn. R. 7007.3000, To avoid major source under 40
CFR 70.2 & Minn. R. 7007.0200]
5.8.2 The Permittee shall limit the production of Hot Mix Asphalt
<= 550,000 tons per year 12-month rolling sum as defined in
Minn. R. 7007.0100, subp. 21a. [Minn. R. 7007.0800, subp. 2, Title
I Condition: Avoid major source under 40 CFR 52.21(b)(1) &
Minn. R. 7007.3000, To avoid major source under 40 CFR 70.2 &
Minn. R. 7007.0200]
5.8.3 The Permittee shall limit Total Particulate Matter <= 90
milligrams per dscm. [40 CFR 60.92(a)(1), Minn. R. 7011.0909]
5.8.4 The Permittee shall limit Opacity <= 20 percent opacity.
[40 CFR 60.92(a)(2), Minn. R. 7011.0909]
5.8.5 Daily Recordkeeping: On each day of operation at the
stationary source, the Permittee shall record and maintain a record
of the total quantity of hot mix asphalt produced. [Minn. R.
7007.0800, subp. 5, Title I Condition: Avoid major source under 40
CFR 52.21(b)(1) & Minn. R. 7007.3000 , To avoid major source
under 40
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 22 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
CFR 70.2 & Minn. R. 7007.0200]
5.8.6 Monthly Recordkeeping: HMA Production By the 15th day of each
month, the Permittee shall calculate and record the following: 1)
The sum of HMA produced by units in COMG7 for the previous month;
and 2) The 12-month rolling sum combined HMA produced for the
previous 12-month period by units in COMG7. [Minn. R. 7007.0800,
subp. 5, Title I Condition: Avoid major source under 40 CFR
52.21(b)(1) & Minn. R. 7007.3000, To avoid major source under
40 CFR 70.2 & Minn. R. 7007.0200]
5.8.7 The Permittee shall determine compliance with the particulate
matter standards as follows: 1) Method 5 shall be used to determine
particulate matter concentration. The sampling time and volume for
each run shall be at least 60 minutes and 0.90 dscm (31.8 dscf);
and 2) Method 9 and the procedures in Section 60.11 shall be used
to determine opacity. [40 CFR 60.93(b)(1)&(2), Minn. R.
7011.0909]
5.8.8 Fuel Usage: The Permittee shall limit fuel usage to natural
gas only, by design. [Minn. R. 7007.0800, subp. 2]
5.8.9 Dryer Burner Tuning: Once each calendar year, the Permittee
shall tune the dryer burner for maximum combustion efficiency. The
Permittee shall keep records of each tuning completed on the burner
and any corrective actions taken. [Minn. R. 7011.0911, subps.
1&3]
5.8.10 The Permittee shall submit a notification of any physical or
operational change which increases emission rate: due 60 days (or
as soon as practical) before the change is commenced. [40 CFR
60.7(a)(4), Minn. R. 7019.0100, subp. 1]
5.8.11 Recordkeeping: The Permittee shall maintain records of the
occurrence and duration of any startup, shutdown, or malfunction in
the operation of the facility including; any malfunction of the air
pollution control equipment; or any periods during which a
continuous monitoring system or monitoring device is inoperative.
[40 CFR 60.7(b), Minn. R. 7019.0100, subp. 1]
5.8.12 Recordkeeping: The Permittee shall maintain a file of all
measurements, maintenance, reports and records for at least five
years. This requirement is more stringent than 40 CFR Section
60.7(f), which specifies two years. [40 CFR 60.7(f), Minn. R.
7007.0800, subp. 5(C), Minn. R. 7019.0100, subp. 1]
5.8.13 Opacity Compliance: The Permittee shall demonstrate
compliance with opacity standards using Reference Method 9. [40 CFR
60.11, Minn. R. 7017.2015]
5.8.14 No owner or operator shall build, erect, install, or use any
article, machine, equipment or process, the use of which conceals
an emission which would otherwise constitute a violation of an
applicable standard. [40 CFR 60.12, Minn. R. 7011.0050]
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 23 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
EQUI1 EU001 HMA Plant Dryer 5.9.1 The Permittee is authorized to
install and operate EQUI1, as defined
by the emissions unit information in Appendix B of this permit, at
any time during the life of Air Emissions Permit No. 03700381-101.
The unit shall meet all the requirements of this permit (e.g.
COMG1). It is the responsibility of the Permittee to determine when
new rules apply to the unit authorized for construction and to
follow them as required. When new rules apply, the Permittee shall
evaluate if a permit amendment is needed and submit the appropriate
amendment following Minn. R. 7007.1150-7007.1500. [Minn. R.
7007.0800, subp. 2]
EQUI2 EU002 HMA Plant Silo
#1
5.10.1 The Permittee is authorized to install and operate EQUI2, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.10.2 The Permittee shall limit Opacity <= 20 percent opacity.
[Minn. R. 7011.0715, subp. 1(B)]
EQUI3 EU003 HMA Plant Silo
#2
5.11.1 The Permittee is authorized to install and operate EQUI3, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.11.2 The Permittee shall limit Opacity <= 20 percent opacity.
[Minn. R. 7011.0715, subp. 1(B)]
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 24 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
EQUI4 EU004 HMA Plant Silo
#3
5.12.1 The Permittee is authorized to install and operate EQUI4, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.12.2 The Permittee shall limit Opacity <= 20 percent opacity.
[Minn. R. 7011.0715, subp. 1(B)]
EQUI6 EU006 Tank Farm Tank
Heater #1
5.13.1 The Permittee is authorized to install and operate EQUI6, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.13.2 The Permittee shall limit Total Particulate Matter <=
0.40 pounds per million Btu heat input. The potential to emit from
the unit is 0.0076 lb/MMBtu due to equipment design and allowable
fuels. [Minn. R. 7011.0515, subp. 1]
5.13.3 The Permittee shall limit Opacity <= 20 percent opacity
except for one six-minute period per hour of not more than 60
percent opacity. [Minn. R. 7011.0515, subp. 2]
EQUI7 EU007 Tank Farm Tank
Heater #2
5.14.1 The Permittee is authorized to install and operate EQUI7, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 25 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
them as required. When new rules apply, the Permittee shall
evaluate if a permit amendment is needed and submit the appropriate
amendment following Minn. R. 7007.1150-7007.1500. [Minn. R.
7007.0800, subp. 2]
5.14.2 The Permittee shall limit Total Particulate Matter <=
0.40 pounds per million Btu heat input. The potential to emit from
the unit is 0.0076 lb/MMBtu due to equipment design and allowable
fuels. [Minn. R. 7011.0515, subp. 1]
5.14.3 The Permittee shall limit Opacity <= 20 percent opacity
except for one six-minute period per hour of not more than 60
percent opacity. [Minn. R. 7011.0515, subp. 2]
EQUI8 TK001 HMA Plant Liquid
AC Storage Tank #1
5.15.1 The Permittee is authorized to install and operate EQUI8, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI9 TK002 HMA Plant Liquid
AC Storage Tank #2
5.16.1 The Permittee is authorized to install and operate EQUI9, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI10 TK003 HMA Plant Liquid
AC Storage Tank #3
5.17.1 The Permittee is authorized to install and operate EQUI10,
as defined by the emissions unit information in Appendix B of
this
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 26 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI11 TK004 Tank Farm AC
Storage Tank #1 (7500 ton)
5.18.1 The Permittee is authorized to install and operate EQUI11,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.18.2 Monitoring of Operations: The Permittee shall maintain a
file specifying each of the following: 1) The type of petroleum
liquid stored; 2) The typical Reid vapor pressure of each type of
petroleum liquid; 3) The dates of storage and withdrawals; and 4)
The date of which the storage vessel is empty. [Minn. R. 7007.0800,
subp. 4, Minn. R. 7011.1510, subp. 1(A)]
EQUI12 TK005 Tank Farm AC
Storage Tank #2 (7500 ton)
5.19.1 The Permittee is authorized to install and operate EQUI12,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.19.2 Monitoring of Operations: The Permittee shall maintain a
file
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 27 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
specifying each of the following: 1) The type of petroleum liquid
stored; 2) The typical Reid vapor pressure of each type of
petroleum liquid; 3) The dates of storage and withdrawals; and 4)
The date of which the storage vessel is empty. [Minn. R. 7007.0800,
subp. 4, Minn. R. 7011.1510, subp. 1(A)]
EQUI13 TK006 Tank Farm AC
Storage Tank #3 (5000 ton)
5.20.1 The Permittee is authorized to install and operate EQUI13,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.20.2 Monitoring of Operations: The Permittee shall maintain a
file specifying each of the following: 1) The type of petroleum
liquid stored; 2) The typical Reid vapor pressure of each type of
petroleum liquid; 3) The dates of storage and withdrawals; and 4)
The date of which the storage vessel is empty. [Minn. R. 7007.0800,
subp. 4, Minn. R. 7011.1510, subp. 1(A)]
EQUI14 TK007 Tank Farm AC
Storage Tank #4 (5000 ton)
5.21.1 The Permittee is authorized to install and operate EQUI14,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.21.2 Monitoring of Operations: The Permittee shall maintain a
file specifying each of the following: 1) The type of petroleum
liquid stored; 2) The typical Reid vapor pressure of each type of
petroleum liquid; 3) The dates of storage and withdrawals;
and
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 28 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
4) The date of which the storage vessel is empty. [Minn. R.
7007.0800, subp. 4, Minn. R. 7011.1510, subp. 1(A)]
EQUI15 TK008 Tank Farm PMAC
Tank #1 (100 ton)
5.22.1 The Permittee is authorized to install and operate EQUI15,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI16 TK009 Tank Farm PMAC
Tank #2 (100 ton)
5.23.1 The Permittee is authorized to install and operate EQUI16,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI17 TK010 Tank Farm Load
out Tank #1 (800 ton)
5.24.1 The Permittee is authorized to install and operate EQUI17,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.24.2 Monitoring of Operations: The Permittee shall maintain a
file
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 29 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
specifying each of the following: 1) The type of petroleum liquid
stored; 2) The typical Reid vapor pressure of each type of
petroleum liquid; 3) The dates of storage and withdrawals; and 4)
The date of which the storage vessel is empty. [Minn. R. 7007.0800,
subp. 4, Minn. R. 7011.1510, subp. 1(A)]
EQUI18 TK011 Tank Farm Load
out Tank #2 (800 ton)
5.25.1 The Permittee is authorized to install and operate EQUI18,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
5.25.2 Monitoring of Operations: The Permittee shall maintain a
file specifying each of the following: 1) The type of petroleum
liquid stored; 2) The typical Reid vapor pressure of each type of
petroleum liquid; 3) The dates of storage and withdrawals; and 4)
The date of which the storage vessel is empty. [Minn. R. 7007.0800,
subp. 4, Minn. R. 7011.1510, subp. 1(A)]
EQUI19 EU008 Pioneer Jaw
Crusher
5.26.1 The Permittee is authorized to install and operate EQUI19,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI20 EU009 Cedar Rapids
Impact Crusher
5.27.1 The Permittee is authorized to install and operate EQUI20,
as defined by the emissions unit information in Appendix B of
this
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 30 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI21 EU010 Electric Cone
Crusher
5.28.1 The Permittee is authorized to install and operate EQUI21,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI22 EU011 Spokane Impact
Crusher
5.29.1 The Permittee is authorized to install and operate EQUI22,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI23 EU012 Screen 1 6'x20' 5.30.1 The Permittee is authorized to
install and operate EQUI23, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 31 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
rules apply to the unit authorized for construction and to follow
them as required. When new rules apply, the Permittee shall
evaluate if a permit amendment is needed and submit the appropriate
amendment following Minn. R. 7007.1150-7007.1500. [Minn. R.
7007.0800, subp. 2]
EQUI24 EU013 Screen 2 5'x20' 5.31.1 The Permittee is authorized to
install and operate EQUI24, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI25 EU014 Screen 3 6'x20' 5.32.1 The Permittee is authorized to
install and operate EQUI25, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI26 EU015 Conveyor 3 (90') 5.33.1 The Permittee is authorized to
install and operate EQUI26, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI27 EU016 Conveyor 4 (90')
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 32 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
5.34.1 The Permittee is authorized to install and operate EQUI27,
as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI28 EU017 Conveyor 22 5.35.1 The Permittee is authorized to
install and operate EQUI28, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI29 EU018 Conveyor 5 (75') 5.36.1 The Permittee is authorized to
install and operate EQUI29, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI30 EU019 Conveyor 6
(200')
5.37.1 The Permittee is authorized to install and operate EQUI30,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1).
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 33 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
It is the responsibility of the Permittee to determine when new
rules apply to the unit authorized for construction and to follow
them as required. When new rules apply, the Permittee shall
evaluate if a permit amendment is needed and submit the appropriate
amendment following Minn. R. 7007.1150-7007.1500. [Minn. R.
7007.0800, subp. 2]
EQUI31 EU020 Conveyor 7 (80') 5.38.1 The Permittee is authorized to
install and operate EQUI31, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI32 EU021 Conveyor 10
(60')
5.39.1 The Permittee is authorized to install and operate EQUI32,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI33 EU022 Conveyor 11
(80')
5.40.1 The Permittee is authorized to install and operate EQUI33,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500.
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 34 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
[Minn. R. 7007.0800, subp. 2]
EQUI34 EU023 Conveyor 12
(50')
5.41.1 The Permittee is authorized to install and operate EQUI34,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI35 EU024 Conveyor 14
(60')
5.42.1 The Permittee is authorized to install and operate EQUI35,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI36 EU025 Conveyor 15
(30')
5.43.1 The Permittee is authorized to install and operate EQUI36,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI37 EU026 Conveyor 16
(50')
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 35 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
5.44.1 The Permittee is authorized to install and operate EQUI37,
as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI38 EU027 Conveyor 17
(125')
5.45.1 The Permittee is authorized to install and operate EQUI38,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI39 EU028 Conveyor 20
(80')
5.46.1 The Permittee is authorized to install and operate EQUI39,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI40 EU029 Conveyor 21
(95')
5.47.1 The Permittee is authorized to install and operate EQUI40,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of
this
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 36 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI41 EU030 Conveyor 23
(60')
5.48.1 The Permittee is authorized to install and operate EQUI41,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI42 EU031 Conveyor 24
(100')
5.49.1 The Permittee is authorized to install and operate EQUI42,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI43 EU032 Conveyor 25
(120')
5.50.1 The Permittee is authorized to install and operate EQUI43,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 37 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
them as required. When new rules apply, the Permittee shall
evaluate if a permit amendment is needed and submit the appropriate
amendment following Minn. R. 7007.1150-7007.1500. [Minn. R.
7007.0800, subp. 2]
EQUI44 EU033 Conveyor 26
(60')
5.51.1 The Permittee is authorized to install and operate EQUI44,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI45 EU034 Conveyor 27
(60')
5.52.1 The Permittee is authorized to install and operate EQUI45,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
EQUI46 EU035 Conveyor 8 (40') 5.53.1 The Permittee is authorized to
install and operate EQUI46, as
defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R.
7007.1150-7007.1500. [Minn. R. 7007.0800, subp. 2]
Permit Issued: June 1, 2017 Permit No. 03700381-101 Permit Expires:
Non-expiring Page 38 of 62
Subject Item Sec.SI.Reqt SI des:SI desc Requirement & Citation
EQUI47 EU036 Conveyor 9
(120')
5.54.1 The Permittee is authorized to install and operate EQUI47,
as defined by the emissions unit information in Appendix B of this
permit, at any time during the life of Air Emissions Permit No.
03700381-101. The unit shall meet all the requirements of this
permit (e.g. COMG1). It is the responsibility of the Permittee to
determine when new rules apply to the unit authorized for
construction and to follow them as required. When new rules apply,
the Permittee shall evaluate if a permit amendment is needed and
submit the appropriate amendment following Minn. R. 7007.1150-70