Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Ain Shams Engineering Journal
Chemical and Physical Properties of Poly(Lactic) Acid (PLA) Modified Bitumen--Manuscript Draft--
Manuscript Number: ASEJ-D-19-00656R2
Article Type: Full Length Article
Section/Category: Civil Engineering
Keywords: Chemical interaction; Compatibility; Dispersity; Modified bitumen; Physicalproperties; Poly(Lactic) Acid.
Corresponding Author: Nur Izzi Md Yusoff, PhDUniversiti Kebangsaan MalaysiaBangi, MALAYSIA
First Author: Nashriq Jailani, MSc
Order of Authors: Nashriq Jailani, MSc
Ahmad Nazrul Hakimi Ibrahim, PhD
Abdur Rahim, PhD
Ahmad Kamil Arshad, PhD
Norhidayah Abdul Hassan, PhD
Nur Izzi Md Yusoff, PhD
Abstract: This study investigates the feasibility and effect of poly(lactic) acid (PLA) on bitumenmodification. The chemical and physical properties were evaluated for the modifiedbitumen produced with varying percentages of PLA ranging from 3 to 9%. Severaltestings such as the nuclear magnetic resonance (NMR), Fourier Transform InfraredSpectroscopy (FTIR), Gel permeation chromatography (GPC), penetration, softeningand ductility, and thermal storage stability were evaluated. The results show thatchemical interaction exists between PLA and bitumen. The GPC analysis indicateshigh compatibility of the bitumen with the PLA modifier. Moreover, the results indicatedthat the addition of PLA increased the consistency of modified bitumen. The storagestability and segregation of phases were positively affected in the PLA modifiedbitumen. The PLA and base bitumen interact at physical and chemical levels whichresults in enhancement of performance of modified bitumen to produce a high-qualitybinding material for pavement construction.
Response to Reviewers: List of comments and response
Point 1: More suitable title should be selected for the article.Response 1: The authors has changed the manuscript title to “Chemical and PhysicalProperties of Poly (Lactic) Acid Modified Bitumen”.
Point 2: The abstract should state briefly the purpose of the research, the principalresults and major conclusions. An abstract is often presented separately from thearticle, so it must be able to stand alone.Response 2: The abstract in the revised manuscript has been rewritten and restructurebased on suggested outline by Reviewer 4.
Point 3: It is suggested to present the structure of the article at the end of theintroduction.Response 3: The structure of article was presented at the end of the introduction.
Point 4: The major defect of this study is the debate or Argument is not clear stated inthe introduction session. Hence, the contribution is weak in this manuscript. I wouldsuggest the author to enhance your theoretical discussion and arrives your debate orargument.Response 4: The authors has revised and restructured the whole introduction sectionin the revised manuscript. The revised introduction provided a well discuss related thetheoretical and finding of the previous related works. In addition, the limitation of the
Powered by Editorial Manager® and ProduXion Manager® from Aries Systems Corporation
previous works is well derived and identified as the main reason this study wasconducted.
Point 5: The necessity and innovation of the article should be presented to theintroduction.Response 5: Based on limitation of the previous works, this study was conducted tobridge the gap of knowledge. The necessity of this study is presented in theintroduction and the innovation of this study is described as well in the revisedmanuscript.
Point 6: More suitable title should be presented for the figure 11 instead of "Softeningpoint value of PLA-modified bitumen".Response 6: The title of Figure 11 and Figure 12 in the revised manuscript has beenrevised.
Point 7: It is suggested to compare the results of the present research with somesimilar studies which is done before.Response 7: The findings of this study was compared to the results of the relatedprevious studies. The discussion of this can be seen in Section 3 (Results) and Section4 (Discussion).
Point 8: A flowchart should be added to the article to show the research methodology.Response 8: The flow chart was added in Figure 1 to summarize the flow of researchprotocol.
Point 9: Following, you will find some new related references which should be added toliterature review:Saedi & Oruc. The Effects of Nano Bentonite and Fatty Arbocel on Improving theBehavior of Warm Mixture Asphalt against Moisture Damage and Rutting;Shihab et al. Effects of Temperature in Different Initial Duration Time for Soft ClayStabilized by Fly Ash Based Geopolymer;Nhabih et al. Study a Structural Behavior of Eccentrically Loaded GFRP ReinforcedColumns Made of Geopolymer Concrete.Response 9: The relevant information from these suggested studies have been used toenhance the sentence and discussion in the revised manuscript. In addition, thesesuggested studies were added in the revised manuscript.
Point 10: Page 11: the following paragraph is unclear, so please reorganize that:"Lower indexes were observed for the area under the band of C-O with C-C for theunwashed (11.0 to 7.0%) and washed (10.6 to 5.1%) samples. On the other hand, anincreasing index pattern was observed for both the C=O bond with C-C (unwashed=4.7 to 17.9%; washed=12.1 to 16.9%) and the C=O with C=C (unwashed=1.0 to 7.3%;washed=9.0 to 18.9%).".Response 10: This sentence has been revised.
Point 11: Much more explanations and interpretations must be added for the Results,which are not enough.Response 11: The authors has extended the explanations and interpretations of thefindings in this study. See Result and Discussion section.
Point 12: It is suggested to add articles entitled "Iqbal et al. Improving the AgingResistance of Asphalt by Addition of Polyethylene and Sulphur", "Kadhim & Al-Mutairee. An Experimental Study on Behavior of Sustainable Rubberized ConcreteMixes" and "Trang et al. The Study of Dynamics Heterogeneity in SiO2 Liquid" to theliterature review.Response 12: The relevant information from these suggested studies have been usedto enhance the sentence and discussion in the revised manuscript. In addition, thesesuggested studies were added in the revised manuscript.
Point 13: Please make sure your conclusions' section underscore the scientific valueadded of your paper, and/or the applicability of your findings/results, as indicatedpreviously. Please revise your conclusion part into more details. Basically, you shouldenhance your contributions, limitations, underscore the scientific value added of yourpaper, and/or the applicability of your findings/results and future study in this session.
Powered by Editorial Manager® and ProduXion Manager® from Aries Systems Corporation
Response 13: The authors has rewritten and restructure the conclusion of this study. Inaddition, the suggestion for future research also listed in the same section.
Point 14: "Notation" should be added to the article.Response 14: The “notation” was added in the figure and text in the revisedmanuscript.
Point 15: DOI of the references must be added (you can use "https://crossref.org/").Response 15: The DOI number was added for all references in the revised manuscript.Thank you for your suggestion of using "https://crossref.org/". See Reference section.
Powered by Editorial Manager® and ProduXion Manager® from Aries Systems Corporation
MS ISO 9001:2008 Cert. No. : AR 5779
JABATAN KEJURUTERAAN AWAM, FAKULTI KEJURUTERAAN DAN ALAM BINA, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor Darul Ehsan
Telefon: +603-8921 6447 Faksimili: +603-8911 8344 E-mel: [email protected] Laman Web: http://www.eng.ukm.my
Fakulti Kejuruteraan dan Alam Bina Faculty of Engineering and Built Environment
Chief-in-Editor Ain Shams Engineering Journal 26th December 2020 Dear Prof, SUBMISSION OF A REVISED MANUSCRIPT – R2 FOR POSSIBLE PUBLICATION IN AIN SHAMS ENGINEERING JOURNAL Hereby I have attached a revised manuscript entitled “Effects of Chemical and Physical Properties of Poly(Lactic) Acid (PLA) Modified Bitumen” co-authored by Nashriq Jailani, Ahmad Nazrul Hakimi Ibrahim, Abdur Rahim, Ahmad Kamil Arshard, Norhidayah Abdul Hassan and Nur Izzi Md Yusoff for a possible publication in the Ain Shams Engineering Journal. Please do not hesitate to get in touch with me if you have any questions and I look forward to hearing from you very soon. Thank you very much indeed.
Kind regards, Assoc Prof. Ir. Dr. Nur Izzi Md. Yusoff Dept. of Civil Engineering Faculty of Engineering and Built Environment Universiti Kebangsaan Malaysia 43600 UKM Bangi Selangor, Malaysia Tel: +603-8921 6447 (office), +6019-289 1221 (mobile) Fax: + 603-8921 6147 Email: [email protected], [email protected]
Izzi
Cover Letter
CORRECTION REPORT
TITLE:
Chemical and Physical Properties of Poly (Lactic) Acid Modified Bitumen
(REF: ASEJ-D-19-00656R1)
We are very pleased to have been given the opportunity to revise our manuscript, which is entitled,
“Chemical and Physical Properties of Poly (Lactic) Acid Modified Bitumen” for the Ain Shams
Engineering Journal. We have carefully considered those offered by a reviewer. Here, we explain how
we have revised the paper based on those comments and recommendations. We would like to extend our
gratitude all parties for taking the time and making the effort to provide such insightful guidance.
The response to all comments from Reviewer 4 is shown in the list of comments and response
and attached revised manuscript.
In conclusion, we appreciate all the insightful comments. We have done our best to make the
recommended amendments. Thank you for the time and effort to help us improve the writing
of this paper. We hope that you will approve the revised version of this paper.
Thank you.
Detailed Response to Reviewers
List of comments and response
Point 1: More suitable title should be selected for the article.
Response 1: The authors has changed the manuscript title to “Chemical and Physical Properties
of Poly (Lactic) Acid Modified Bitumen”.
Point 2: The abstract should state briefly the purpose of the research, the principal results and
major conclusions. An abstract is often presented separately from the article, so it must be able
to stand alone.
Response 2: The abstract in the revised manuscript has been rewritten and restructure based
on suggested outline by Reviewer 4.
Point 3: It is suggested to present the structure of the article at the end of the introduction.
Response 3: The structure of article was presented at the end of the introduction.
Point 4: The major defect of this study is the debate or Argument is not clear stated in the
introduction session. Hence, the contribution is weak in this manuscript. I would suggest the
author to enhance your theoretical discussion and arrives your debate or argument.
Response 4: The authors has revised and restructured the whole introduction section in the
revised manuscript. The revised introduction provided a well discuss related the theoretical and
finding of the previous related works. In addition, the limitation of the previous works is well
derived and identified as the main reason this study was conducted.
Point 5: The necessity and innovation of the article should be presented to the introduction.
Response 5: Based on limitation of the previous works, this study was conducted to bridge the
gap of knowledge. The necessity of this study is presented in the introduction and the
innovation of this study is described as well in the revised manuscript.
Point 6: More suitable title should be presented for the figure 11 instead of "Softening point
value of PLA-modified bitumen".
Response 6: The title of Figure 11 and Figure 12 in the revised manuscript has been revised.
Point 7: It is suggested to compare the results of the present research with some similar studies
which is done before.
Response 7: The findings of this study was compared to the results of the related previous
studies. The discussion of this can be seen in Section 3 (Results) and Section 4 (Discussion).
Point 8: A flowchart should be added to the article to show the research methodology.
Response 8: The flow chart was added in Figure 1 to summarize the flow of research protocol.
Point 9: Following, you will find some new related references which should be added to
literature review:
Saedi & Oruc. The Effects of Nano Bentonite and Fatty Arbocel on Improving the Behavior of
Warm Mixture Asphalt against Moisture Damage and Rutting;
Shihab et al. Effects of Temperature in Different Initial Duration Time for Soft Clay Stabilized
by Fly Ash Based Geopolymer;
Nhabih et al. Study a Structural Behavior of Eccentrically Loaded GFRP Reinforced Columns
Made of Geopolymer Concrete.
Response 9: The relevant information from these suggested studies have been used to enhance
the sentence and discussion in the revised manuscript. In addition, these suggested studies were
added in the revised manuscript.
Point 10: Page 11: the following paragraph is unclear, so please reorganize that:
"Lower indexes were observed for the area under the band of C-O with C-C for the unwashed
(11.0 to 7.0%) and washed (10.6 to 5.1%) samples. On the other hand, an increasing index
pattern was observed for both the C=O bond with C-C (unwashed= 4.7 to 17.9%; washed=12.1
to 16.9%) and the C=O with C=C (unwashed=1.0 to 7.3%; washed=9.0 to 18.9%).".
Response 10: This sentence has been revised.
Point 11: Much more explanations and interpretations must be added for the Results, which
are not enough.
Response 11: The authors has extended the explanations and interpretations of the findings in
this study. See Result and Discussion section.
Point 12: It is suggested to add articles entitled "Iqbal et al. Improving the Aging Resistance
of Asphalt by Addition of Polyethylene and Sulphur", "Kadhim & Al-Mutairee. An
Experimental Study on Behavior of Sustainable Rubberized Concrete Mixes" and "Trang et al.
The Study of Dynamics Heterogeneity in SiO2 Liquid" to the literature review.
Response 12: The relevant information from these suggested studies have been used to
enhance the sentence and discussion in the revised manuscript. In addition, these suggested
studies were added in the revised manuscript.
Point 13: Please make sure your conclusions' section underscore the scientific value added of
your paper, and/or the applicability of your findings/results, as indicated previously. Please
revise your conclusion part into more details. Basically, you should enhance your contributions,
limitations, underscore the scientific value added of your paper, and/or the applicability of your
findings/results and future study in this session.
Response 13: The authors has rewritten and restructure the conclusion of this study. In
addition, the suggestion for future research also listed in the same section.
Point 14: "Notation" should be added to the article.
Response 14: The “notation” was added in the figure and text in the revised manuscript.
Point 15: DOI of the references must be added (you can use "https://crossref.org/").
Response 15: The DOI number was added for all references in the revised manuscript. Thank
you for your suggestion of using "https://crossref.org/". See Reference section.
Chemical and Physical Properties of Poly (Lactic) Acid Modified Bitumen
Nashriq Jailani1, Ahmad Nazrul Hakimi Ibrahim2, Abdur Rahim3, Ahmad Kamil Arshad4,
Norhidayah Abdul Hassan5 and Nur Izzi Md. Yusoff6*
1PhD Student, Dept. of Civil Engineering, Faculty of Engineering and Built Environment,
Universiti Kebangsaan Malaysia, Selangor, Malaysia
Email: [email protected]
2PhD Student, Dept. of Civil Engineering, Faculty of Engineering and Built Environment,
Universiti Kebangsaan Malaysia, Selangor, Malaysia
Email: [email protected]
3Senior Lecturer (Dr.), Dept. of Transportation Engineering and Management, University of
Engineering and Technology, Lahore, Pakistan
Email: [email protected]
4Prof. (Ir. Dr.), Institute for Infrastructure Engineering and Sustainable Management,
Universiti Teknologi MARA, Shah Alam, Selangor, Malaysia
Email: [email protected]
5Senior Lecturer (Dr.), School of Civil Engineering, Universiti Teknologi Malaysia, Johor,
Malaysia
Email: [email protected]
6Associate Prof. (Ir. Dr.), Dept. of Civil Engineering, Faculty of Engineering and Built
Environment, Universiti Kebangsaan Malaysia, Selangor, Malaysia
Email: [email protected]
*Corresponding author: [email protected]
Title Page (with AU credentials)
1
Chemical and Physical Properties of Poly (Lactic) Acid Modified Bitumen 1
2
Abstract 3
4
This study investigates the feasibility and effect of poly(lactic) acid (PLA) on bitumen 5
modification. The chemical and physical properties were evaluated for the modified bitumen 6
produced with varying percentages of PLA ranging from 3 to 9%. Several testings such as the 7
nuclear magnetic resonance (NMR), Fourier Transform Infrared Spectroscopy (FTIR), Gel 8
permeation chromatography (GPC), penetration, softening and ductility, and thermal storage 9
stability were evaluated. The results show that chemical interaction exists between PLA and 10
bitumen. The GPC analysis indicates high compatibility of the bitumen with the PLA modifier. 11
Moreover, the results indicated that the addition of PLA increased the consistency of modified 12
bitumen. The storage stability and segregation of phases were positively affected in the PLA 13
modified bitumen. The PLA and base bitumen interact at physical and chemical levels which 14
results in enhancement of performance of modified bitumen to produce a high-quality binding 15
material for pavement construction. 16
17
Keywords: Chemical interaction; Compatibility; Dispersity; Modified bitumen; Physical 18
properties; Poly(Lactic) Acid 19
20
1. Introduction 21
22
Bitumen is produced by refining crude oil through a series of distillation processes and it is 23
composed of heavy hydrocarbons, which are classified into saturates, aromatics, resins and 24
asphaltenes (Günay & Ahmedzade 2020). It is used in various engineering applications such 25
as highway and airfield pavement due to its physical and rheological characteristics as well as 26
impermeability and adhesive properties (Farias et al., 2016; Mohammadiroudbari et al., 2016). 27
However, being a viscoelastic material, bitumen is easily affected by seasonal temperature and 28
rain as well as loading factors including increasing traffic volumes and continuous heavy loads 29
(Ibrahim et al. 2016; 2017; Iqbal et al. 2020). The viscoelastic properties of bitumen are time 30
and temperature dependant. This effect changes in its physical properties, which are reflected 31
in the mechanical properties of asphalt mixtures. Therefore, bitumen should be sufficiently stiff 32
to resist rutting at high temperatures and soft at low temperatures to prevent the occurrence of 33
thermal cracking (Lesueur, 2009; Saedi & Oruc 2020). 34
Manuscript text (without AU credentials)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
2
35
The performance bitumen is, traditionally, enhanced with different types of modifiers 36
including; nanomaterial (Omar et al., 2018; Yusoff et al., 2019), geopolymer (Ali et al., 2017; 37
Ibrahim et al., 2016; Rosyidi et al. 2020; Shihab et al. 2018), waste materials such as glass and 38
plastic (Zakaria et al., 2018), and rubber (Al Mansoob et al., 2017). The previous studies 39
indicate that the addition of modifier improves the performance of the binder in terms of 40
elasticity and stiffness, and also reduces the permanent deformation of the pavement resulting 41
from environmental effects and repetitive traffic loading (Braseileiro et al., 2014; Giavarini et 42
al., 1996; Panda & Mazumdar, 1999). However, amongst the different types of bitumen 43
modifiers, the polymers are the frequently used as modifiers and have demonstrated to be good 44
modifying agents in the production of high-performance binder (Brasileiro et al., 2019; Polacco 45
et al., 2005; Padhan & Gupta, 2018; Sengoz et al., 2009; Zhu et al., 2014). 46
47
The evidence for performance enhancement with polymers is demonstrated by Jiang et 48
al. (2020) and Laukkanen et al. (2018). According to the studies, the modification of bitumen 49
with SBS enhances the engineering properties of the bitumen for reduced temperature 50
dependence, increased elasticity, as well as an enhanced performance at low and high service 51
temperature. This is due to the excellent mechanical properties of SBS such as high fatigue 52
resistance, elastic recovery and high resistance at extreme temperatures (Airey, 2004; Chen et 53
al. 2007; Schaur et al. 2017). Another thermoplastic modifier that has been widely used for 54
bitumen modification is crumb rubber (CR). According to Poovaneshvaran et al. (2020), Wang 55
et al. (2020a, 2020b, 2020c) and Yao et al. (2018) CR can modify the physical and mechanical 56
properties of bitumen to produce improved resistance to fatigue and thermal cracking, ageing, 57
and rutting. Loderer et al. (2018) reported that, unlike SBS-modified bitumen, CR-modified 58
bitumen has a high resistance to rutting and low-temperature cracking. Moreover, other studies 59
on bitumen modification with natural rubber show enhancement of physical and rheological 60
properties of the modified bitumen (Al-Mansob et al. 2014) and improvement in resistance to 61
shear stress (Poovaneshvaran et al. 2020). Furthermore, the modification of bitumen with 62
polymers has demonstrated to improve the binder properties, for instance, enhanced stiffness 63
at high temperatures, cracking resistance at low temperatures, moisture resistance, and longer 64
fatigue life (Alata et al., 2013; Gardiner et al., 1995; Al Mansoob et al., 2017). The promising 65
potential of using polymers such as rubber and geopolymer is not limited to the bituminous 66
materials only. Numerous evidences were found related to the promising effect of using these 67
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
3
polymers in other applications including as structural and concrete materials (Nhabih et al. 68
2020; Kadhim & Al-Mutairee 2020). 69
70
The findings of the previous studies related to the polymer modified bitumen are 71
promising and establish the applicability of polymer in bitumen. Within this scope, this 72
research explores the potential of PLA as a modifier. PLA is a bio-based green thermoplastic 73
polyester which can be derived from renewable resources such as sugarcane or cornstarch 74
(Auras et al., 2004; Rasal et al., 2010). Furthermore, PLA is an attractive substitute for 75
conventional polymers due to its excellent biocompatibility, high tensile strength, and high 76
modulus. The simplicity of the PLA structure with esters as the repeating unit and carboxyl 77
group as the end chain can explain the chemical reaction that occurs between PLA and bitumen. 78
79
The pavement engineering field, traditionally, has remained less focused on the 80
chemical reaction occurring between the polymers and bitumen. Since the past several years, 81
the major concern in literature is enhancing the stability and compatibility of bitumen-polymer 82
blends and optimizing the formulation of the blends (Wang et al. 2020). Most reported works 83
on the utilization of polymers as a modifier focus on describing the physical dispersion of 84
polymers in bitumen while ignoring the chemical reaction that occurs in the blend (Yusoff et 85
al. 2014; Rosyidi et al. 2020). 86
87
In view of the limitations of previous works, this study aims to investigate the chemical 88
and physical performance of modified bitumen with a new bitumen modifier known as 89
poly(lactic) acid (PLA). This research examines the chemical interaction occurring between 90
the PLA and the base bitumen by using multiple spectroscopic techniques. The relationship of 91
the interactions is then confirmed using the sequential dissolution approach, where a reaction 92
mechanism between PLA and bitumen is also proposed. The PLA-bitumen compatibility and 93
the dispersion of PLA in bitumen are also discussed. The current study will be useful to 94
understand the behaviour and properties of PLA in bitumen modification for its potential 95
utilization in pavement engineering. The remainder of this paper is structured as follows. 96
Section 2 describes the materials, blending and testing protocol. Section 3 presents the results 97
and discussion of the outcome in this study. The paper ends with conclusion and 98
recommendations for future research in Section 4. 99
100
101
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
4
2. Material and Methods 102
103
2.1. Materials 104
105
Poly(lactic) acid (PLA) in pellet form with a melt flow index (MFI) of 20 g/10 min (190 106
°C/2.16 kg) and a density of 1.24 g/cm3 was purchased from Shenzhen Bright China Industrial 107
Co, while the chloroform was obtained from Merck Pvt Ltd, Selangor, Malaysia. The filter 108
paper (Whatman, 150mm, Catalog Number 1001-150) was purchased from a local supplier, 109
and the 60/70 penetration grade bitumen was supplied by a refinery in Port Klang, Malaysia. 110
The physical properties of the 60/70 penetration grade bitumen used in this study are presented 111
in Table 1. 112
113
Table 1: Physical properties of 60/70 penetration grade bitumen 114
Parameter Standard Unit Specification
Penetration at 25°C ASTM D5 mm/10 60/70
Softening point ASTM D36 °C 49/56
Ductility at 25°C ASTM D113 cm 100 min
Loss of heating ASTM D6 wt. % 0.2 max
Drop in penetration after heating ASTM D5-D6 % 20 max
115
2.2. Preparation of bitumen blends 116
117
Aluminum cans (500 cm3) were filled with 200 g of 60/70 penetration grade bitumen and put 118
in a 150 °C oven until they are ready for use. The PLA was dissolved in an appropriate volume 119
of chloroform to obtain a final concentration of 3, 5, 7 and 9 wt. % by base bitumen (250g). 120
The semi-liquid PLA was gradually added (2 mL/min) to the base bitumen at 180 ± 2 °C and 121
a high-shear mixer to blend at 1000 ± 10 rpm for two hours to obtain a homogenous mixture. 122
After this step, the mixture was aliquoted into different cans for subsequent physical and 123
chemical testing. The experimental process of the development of PLA modified bitumen is 124
presented in Figure 1. 125
126
127
128
129
130
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
5
131
132
133
134
135
136
137
138
139
140
141
Figure 1: Research methodology 142
143
2.3. Characterization of reactive polymer with bitumen 144
145
Proton (1H)-nuclear magnetic resonance (NMR) spectra was used to study the structural 146
distribution of PLA and their interaction with the bitumen. The analysis was carried out using 147
the Brucker Advance III HD 400MHz 1-Dimensional NMR spectroscopy with 148
tetramethylsilane (TMS) as the internal standard. Each sample was dissolved in deuterated 149
chloroform (CDCl3) to a final concentration of 10% w/v and the run time was 10 minutes. 150
Fourier-Transform Infrared spectroscopy (FT-IR) was carried out to determine the functional 151
groups and the chemical bonds in the PLA-modified bitumen. All samples were tested in 152
triplicate using the Perkin Elmer Spectrum 400-FT-IR spectrometer. 153
154
The compatibility of PLA with base bitumen was determined by analyzing the 155
asphaltenes using sequential dissolution via staged extraction approach. The 100 mg samples 156
of bitumen and modified bitumen with 3, 5, 7 and 9% PLA, were washed three times with 10 157
mL of chloroform. Each layer was then filtered with using a filter paper. The residue (in the 158
form of asphaltenes) retained on the filter paper was weighed and compared with the control 159
bitumen. Next, the extracted asphaltenes from the third wash of each sample were recovered 160
and characterized using FT-IR spectroscopy. 161
162
Gel permeation chromatography (GPC) was employed to analyze the dispersity of PLA 163
in the base bitumen. Dispersity was determined based on molar mass and molar-mass 164
Materials selection and
characterisation
Blending process
Chemical characterization
of PLA modified bitumen
Physical characterization
of PLA modified bitumen
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
6
distribution of the polymer obtained from GPC (Waters 1515) equipped with differential 165
refractive index (RI 2410) and ultraviolet (UV 2487) detectors. The molar masses were 166
separated using Waters Styragel columns in a series with the molar mass ranging from 100-167
500 000 gmol-1. The samples were dissolved in chloroform and analyzed using tetrahydrofuran 168
(THF) as the eluent at a flow rate of 1.0 mL/min (30 °C) for 40 minutes. 169
170
2.4. Characterization of PLA-modified bitumen 171
172
The physical characterization of PLA-modified bitumen includes performing the penetration 173
test at a fixed temperature (25 °C) according to ASTM D5 while the softening point was 174
measured with ring and ball approach as per ASTM D36-06 standard. The stability test was 175
carried out by placing the bitumen in an aluminum-covered tube with a diameter of 3.5 cm and 176
a height of 30 cm in a 180 °C oven for three days. The samples were then cooled at ambient 177
temperature and then cut into three sections. The upper and lower sections of each sample were 178
subjected to softening temperature test. The degree of homogeneity of the mixture is indicated 179
by differences in softening temperature between the two sections, where a smaller difference 180
indicates high compatibility of the PLA with bitumen. The ductility test was carried out 181
according to ASTM D113 standard at 25 °C. 182
183
3. Results and Discussion 184
185
3.1. Characterization of PLA-bitumen reaction 186
187
3.1.1. 1-Dimensional Nucleus Magnetic Resonance Proton (1H 1D-NMR) analysis 188
189
In order to demonstrate the interaction between PLA and bitumen, a representative 1H NMR 190
spectrums and the assigned signals of the control and the bitumen modified with varying 191
percentages of PLA (Figure 2-4). The results in Figure 2 show that there are multiple signals 192
from the chemical shift from 0.8 to 3.5 ppm. The signals were assigned as two parts, the part 193
‘a’ ranges from 0.8 to 1.4 ppm and represents the signals of the aliphatic proton from alkanes. 194
The ‘b’ ranges from 1.5 to 3.5 ppm and represents the protons from alkenes, alkynes or aliphatic 195
with carbonyl such as ketone, aldehyde, ester and carboxyl group. The chemical structure for 196
poly(lactic) acid is shown in Figure 3, where two signals have been detected. The doublet peak 197
absorbed at a chemical shift from 1.58 to 1.60 ppm (labelled c) indicates a proton from methyl 198
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
7
group (-CH3), and the quartet peak at 5.15-5.20 ppm (labelled d) indicates a proton from the 199
ester side chain (-OCH(CH3)-) of the repeating unit of PLA. Figure 4 shows the stacked NMR 200
of the bitumen modified with 3, 5, 7 and 9% PLA. The four detected signals (a, b, c and d) 201
indicate the occurrence of a chemical interaction between the PLA and the bitumen. The 202
increase in the intensity of the doublet and quartet (peaks c and d) corresponds with the high 203
percentage of PLA in the samples. A comparison with the control bitumen shows the 204
suppression of the signals in the ‘b’ region (Figure 4B) of the PLA-modified bitumen. 205
206
207
Figure 2: 1H-NMR spectrum of control bitumen. 208
Nashriq_bitumen + Rh-WMA.001.001.1r.esp
7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0
Chemical Shift (ppm)
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
No
rma
lize
d In
ten
sity
CDCl3
Nashriq_bitumen + Rh-WMA.001.001.1r.esp
8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0
Chemical Shift (ppm)
0
0.005
0.010
0.015
0.020
0.025
No
rma
lize
d Inte
nsity
a
b
b
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
8
209
Figure 3: 1H-NMR spectrum of PLA 210
211
212
Nashriq_PLA only.001.001.1r.esp
7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5
Chemical Shift (ppm)
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
No
rma
lize
d Inte
nsity
7.2
7
5.2
05
.18
5.1
65
.15
1.6
01
.58
Nashriq_PLA only.001.001.1r.esp
2.35 2.30 2.25 2.20 2.15 2.10 2.05 2.00 1.95 1.90 1.85 1.80 1.75 1.70 1.65 1.60 1.55 1.50 1.45 1.40 1.35 1.30 1.25 1.20 1.15
Chemical Shift (ppm)
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
Norm
alize
d Inte
nsity
1.60
1.58
CDCl3
Nashriq_PLA only.001.001.1r.esp
5.65 5.60 5.55 5.50 5.45 5.40 5.35 5.30 5.25 5.20 5.15 5.10 5.05 5.00 4.95 4.90 4.85 4.80
Chemical Shift (ppm)
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
No
rma
lize
d Inte
nsity
5.2
0
5.1
8
5.1
6
5.1
5
HO
CH3
O
O CH3
O
O CH3
OH
O
H
nc
d
c
d 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
9
213
Figure 4: (A) 1H-NMR spectrum of the bitumen modified with 3, 5, 7 and 9% PLA. (B) 214
Zoom 1H-NMR spectrum between 0.5 to 3.0 ppm of the bitumen modified with 3, 5, 7 and 215
9% PLA 216
217
3.1.2. Fourier-Transform Infrared (FT-IR) analysis 218
219
Figure 5 shows a comparison of the FT-IR spectrum of the control bitumen, PLA and the 220
bitumen modified with 3, 5, 7 and 9% PLA. The spectrum shows that the bitumen modified 221
with different percentages of PLA have similar overlapping profiles. A comparison of the 222
spectrum for samples modified with PLA with control bitumen and PLA shows an almost 223
similar profile except for the additional bands at 1098 cm-1 (region i) and 1749 cm-1 (region ii) 224
in the modified bitumen. This indicates the simultaneous presence of the carbon-oxygen (C-O) 225
and carbonyl (C=O) functional groups. A comparison with the PLA spectrum shows a 226
decreased transmittance percentage in the PLA-modified bitumen in region iii (3600-3650 cm-227
1) for the band representing the hydroxyl group (OH). 228
Nashriq_3% PLA.001.001.1r.esp
8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0
Chemical Shift (ppm)
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
No
rma
lize
d Inte
nsity
3% PLA
5% PLA
7% PLA
9% PLA
CDCl3
Bitumen
(A) (B) c
d
b
a
Nashriq_3% PLA.001.001.1r.esp
8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0
Chemical Shift (ppm)
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
Norm
alize
d Inte
nsity
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
10
229
Figure 5: FT-IR spectrum of the control bitumen, PLA and bitumen modified with 3, 5, 7 230
and 9% PLA 231
232
The compatibility of PLA with bitumen was investigated using sequential dissolution 233
technique via the staged extraction method. The asphaltenes from each sample (the third wash) 234
were extracted and sent for FT-IR analysis to determine their carbonyl index. Figure 6 shows 235
the percentage of asphaltenes for bitumen modified with 3, 5, 7 and 9% PLA. The results are 236
comparable with the percentage of the control bitumen (~14.4%), except for higher asphaltenes 237
content observed in the bitumen modified with 9% PLA (18.1%). Based on the FT-IR 238
spectrum, the carbonyl index (CI) was determined by calculating the area under the carbonyl 239
band absorbed at wavelength 1695 cm-1 and the saturated C-C band at 1455 cm-1 (Eq. 1). The 240
same asphaltenes residue shows that the carbonyl index of the bitumen modified with 3, 5 and 241
7% PLA are slightly higher (~16.3%) than that of the control bitumen (14.5%). Similar to the 242
asphaltenes content, bitumen modified with 9% PLA has a high carbonyl index of 19.7% 243
(Figure 6). 244
245
CI = x 100 (1) 246
247
0
20
40
60
80
100
5001000150020002500300035004000
% T
ran
smit
tan
ce
wavenumbers (cm-1)
Bitumen control
PLA
3, 5, 7 and 9% PLA
1749.985 cm-1
1098.9 cm-1
3600- 3650 cm-1
area of carbonyl at 1695 cm-1
Region i Region ii Region iii
area of saturated C-C at 1455 cm-1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
11
248
Figure 6: Compatibility and sequential dissolution of different percentages of PLA and 249
bitumen 250
251
The FT-IR spectrum presented in Figure 5 and the sequential dissolution technique 252
were used as a basis for further investigation of the correlation between the additional C-O 253
band at 1098 cm-1 (region i) and C=O band at 1749 cm-1 (region ii) in the PLA-modified 254
bitumen. The spectrum in Figure 5 which were PLA-modified bitumen was labelled as 255
unwashed (UW) and the PLA-modified bitumen that underwent sequential dissolution notated 256
as washed samples sequential dissolution (WSD). The results were compared to understand the 257
interaction between the PLA and the bitumen. Figure 7 shows the percentage index of C-O 258
bond (region i) while Figure 8 shows the result of C=O (region ii) divided with the area of (A) 259
unsaturated C=C at 1650 cm-1 and (B) saturated C-C at 1455 cm-1. The index pattern of the C-260
O bond is observed to be different from that of C=O when divided with the unsaturated and 261
saturated carbon-carbon interaction. Figure 7 indicates that the UW showed a simultaneous 262
increase from control bitumen in the index of C-O and C=O with C=C from 11.0 to 26.3% and 263
4.7 to 17.9% respectively and C=O with C-C index from 1.0 to 7.3%. While a decreasing 264
pattern of UW sample for C-O bond with C-C index from 11.0 to 7.0% observed. On the other 265
hand, for WSD samples, the result did not show any significant difference in the index of C-O 266
with C=C (~11.1%) except for the 9% PLA (12.7%). Together with UW samples, WSD also 267
showed a decreasing index pattern of C-O bond with C-C from 10.6 to 5.1%. However, an 268
increasing indexes pattern showed for WSD samples of C=O with C=C and C-C each from 269
12.1 to 16.9% and 9.0 to 18.9% respectively. 270
13.8 14.4 14.7 14.5
18.1
14.5016.03 16.23 16.42
19.72
0
5
10
15
20
25
0
5
10
15
20
25
bitumen control 3% PLA 5% PLA 7% PLA 9% PLA
Car
bo
nyl
ind
ex (
%)
Asp
hal
ten
e (%
)asphaltenes
Carbonyl Index
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
12
271
272
Figure 7: Comparison of washed and unwashed indexes of C-O bond at 1749 cm-1 (region i) 273
with (A) C=C, and (B) C-C bonds using FT-IR analysis 274
275
276
277
11.0
18.520.4
23.5
26.3
11.0 11.1 11.2 11.112.7
0
5
10
15
20
25
30
bitumen control 3% 5% 7% 9%
Ind
ex (
%)
unwashed washed
11.0 10.0 9.0 8.0 7.0
10.6 9.78.1
6.55.1
0
5
10
15
20
25
30
bitumen control 3% 5% 7% 9%
Ind
ex (
%)
unwashed washed
4.7
9.911.4
14.5
17.9
12.113.4
14.6 15.416.9
0
5
10
15
20
25
bitumen control 3% 5% 7% 9%
Ind
ex (
%)
unwashed washed
A.
B.
A.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
13
278
Figure 8: Comparison of washed and unwashed indexes of carbonyl at 1749 cm-1 (region ii) 279
with (A) C=C, and (B) C-C bonds using FT-IR analysis 280
281
3.1.3. Gel Permeation Chromatography (GPC) analysis 282
283
The molar mass and molar-mass distribution or dispersity of PLA throughout the bitumen were 284
examined using GPC. Figure 9 is the stacked GPC chromatograms of the control bitumen and 285
the PLA-modified bitumen, while Figure 10 shows the zoom chromatograms of the distribution 286
and dispersity of PLA in bitumen. Two peaks can be seen in the control bitumen sample eluted 287
at retention times of 25.0 and 30.3 minutes. The two major peaks represent bitumen and are 288
present in all PLA-modified bitumen samples (Figure 9). However, Figure 10 shows that, when 289
PLA is added to the bitumen, the increase in the numbers of peaks correspond with the 290
increasing percentage of PLA (from 3, 5, 7 to 9% PLA). The distribution of PLA peaks at a 291
retention time of 25 minutes varies between samples while the major peak (at 30.3 mins) is not 292
affected. The large fragments of PLA peaks eluted at retention time 25 minutes indicate the 293
poly-dispersity of PLA within the samples. Thus, the properties of all peaks at the 25.0-minute 294
retention time were further investigated and the results are shown in Table 2. The table shows 295
that the retention time of the second major peak in all samples shifted about ± 0.1 minutes, the 296
effect of the size of exclusion column separation. The values of peak molecular weight, average 297
molecular weight, average molar mass and molar distribution (dispersity) increased with PLA 298
modification (Table 2). The varying dispersity for the 3 and 5% (1.089 and 1.136) and the 7 299
and 9% (1.653 and 1.984) bitumen-PLA indicate that the dispersity of PLA is enhanced when 300
7% and 9% of PLA were added to the bitumen. 301
302
1.0 1.83.2
5.1
7.39.0
11.113.2
15.8
18.9
0
5
10
15
20
25
bitumen control 3% 5% 7% 9%
Ind
ex (
%)
unwashed washed
B. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
14
303
Figure 9: Gel permeable chromatography (GPC) of the control and modified bitumen 304
Bitumen
3% PLA
5% PLA
7% PLA
9% PLA
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
15
305
Figure 10: Zoom GPC of the control and modified bitumen 306
307
Table 2: Molecular properties of bitumen modified with PLA 308
Sample Retention
time (min)
Peak
Molecular
Weight
(MP)
Average
Molecular
Weight
(Mw)
Average
molar mass
(Mn)
Dispersity
(Mw/Mn)
Control
Sample 25.063 1633 1253 1205 1.039
3% PLA 25.047 1659 1331 1222 1.089
5% PLA 25.154 1701 1456 1281 1.136
7% PLA 25.157 1786 2161 1307 1.653
9% PLA 25.134 1805 2749 1385 1.984
309
Bitumen control
3% PLA
5% PLA
7% PLA
9% PLA
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
16
3.2. Performance of PLA-modified bitumen 310
311
The effect of PLA on the properties of modified bitumen was evaluated based on the physical 312
performance including; penetration, softening point, ductility and storage stability. Figure 11 313
presents the result of the penetration values of the binders. The penetration is an indication of 314
bitumen consistency, which is an empirical measure of the resistance of bitumen to continuous 315
deformation. The addition of PLA to bitumen changes the penetration value of the binders 316
(Figure 11). The bitumen added with more quantity of PLA (7% and 9%) shows low 317
penetration values as compared to the base bitumen. This indicates the ability of the PLA 318
modifier to enhance bitumen stiffness. The penetration result shows a peculiar trend, where the 319
addition of 3% of PLA increases the penetration value up to 18.5% in comparison to the base 320
bitumen, after which penetration gradually decreases with high PLA content. This is due to the 321
dispersion level of PLA in bitumen. Based on dispersity reported earlier, the dispersity of 3% 322
PLA in bitumen is low, and this has the effect of softening the binder. The gradual decrease of 323
the value observed with the addition of high amounts of PLA (5% to 9%) is due to the high 324
dispersity of PLA in bitumen. Furthermore, the high fatigue resistance and elastic recovery of 325
PLA are similar to other thermoplastic materials such as SBS, crumb rubber and natural rubber 326
and contribute to the improvement of bitumen’s consistency (Chen et al. 2007; Schaur et al. 327
2017 Airey, 2004; Chen et al. 2007; Schaur et al. 2017; Poovaneshvaran et al. 2020; and Yao 328
et al. 2018). High amounts of PLA in bitumen results in improved mechanical properties (from 329
PLA) of the modified bitumen, and as a result increases the stiffness of the binder. This increase 330
may also be due to the enhanced structural chain mobility properties of the modified bitumen. 331
332
Figure 11: Penetration values at 25 °C 333
0
10
20
30
40
50
60
70
80
90
Control Sample 3% PLA 5% PLA 7% PLA 9% PLA
Pen
etra
tio
n v
alue
(dm
m)
Type of Sample
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
17
334
The softening point value of PLA-modified bitumen (Figure 12) is directly proportional 335
to the amount of PLA in bitumen. The high PLA content in bitumen increased the asphaltene 336
ratio in modified binders and this contributes to improving the stiffening properties of modified 337
bitumen. As a result, it reduces the susceptibility of the modified binder to temperature changes. 338
The less susceptibility of bitumen such as PLA modified bitumen indicated the high 339
performance of bitumen at high temperature (Zakaria et al., 2018; Al Mansoob et al., 2017). 340
This is congruent with the observation made by Poovaneshvaran et al. (2020), Rosyidi et al. 341
(2020) and Yusoff et al., (2019) about the ability of modified bitumen to withstand high 342
temperatures as compared to base bitumen. In addition, the ductility value of PLA-modified 343
bitumen is >100 cm, which is similar to the value for the base bitumen (See Table 3). The 344
physical properties of PLA-modified bitumen reported in this study are comparable with those 345
reported in earlier studies, including Al-Mansob et al. (2017), Ibrahim et al. (2016), 346
Poovaneshvaran et al. (2020) and Ali et al. (2015). 347
348
349
Figure 12: Softening point values 350
351
On the other hand, the main concern with polymer modified bitumen is the storage 352
stability of the modified bitumen. According to Yu et al. (2015), the modified bitumen is 353
considered stable when the difference between the softening point of the upper and lower 354
sections of the samples after storage under certain condition is less than 2.5 °C. The difference 355
in softening points of the top and bottom sections of the samples determines the degree of phase 356
separation. During high-temperature storage, the phase separation occurs when the modifier is 357
0
10
20
30
40
50
60
70
80
Control Sample 3% PLA 5% PLA 7% PLA 9% PLA
So
ften
ing p
oin
t val
ue
(°C
)
Type of sample
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
18
not dissolved in the modified bitumen and result in the non-homogeneous mixture. 358
Hosseinnezhad et al. (2019) argued that the occurrence of phase separation is influenced by the 359
solubility and particle size of the modifier and density of both the modifier and bitumen. 360
According to the literature, polymer-modified bitumen with poor storage stability is not 361
suitable for paving, roofing, and industrial specialty product applications (Isacsson et al., 1995; 362
Becker et al., 2001; Wahhab et al., 2016). 363
364
Bitumen modified with functionalized polymers, such as PLA, have high thermal 365
stability and no phase separation. This is indicated by the small temperature difference (<2.5 366
°C) between the top and bottom sections of the sample, except for the bitumen modified with 367
9% PLA (See Table 3). The poor thermal storage stability of the bitumen modified with 9% 368
PLA is due to the less compatibility between PLA and bitumen. 369
370
Table 3: Ductility and storage stability of base bitumen and PLA-modified bitumen 371
Sample Ductility at
25 °C (cm)
*Storage Stability
Top (°C) Bottom (°C) Difference (°C) Status
Control
Sample >100 - - - -
3% PLA >100 50 51 1 Good
5% PLA >100 58 60 2 Good
7% PLA >100 59 61 2 Good
9% PLA >100 68 72 4 Poor *difference between the softening point of the top and bottom sections 372
373
3.3 Discussion of the Results 374
375
In this study, polymer modification of bitumen involves the physical blending of the polymer 376
with bitumen as well as the chemical reactions between the two materials as recommended by 377
Brasileiro et al., (2019) and Cardone et al., (2014). Nuclear magnetic resonance (NMR) is a 378
spectroscopic method that can provide information about the number of magnetically distinct 379
atoms such as hydrogen nuclei (protons). NMR differs from Infrared (IR) related to the 380
approach of NMR reveals the type of functional groups present in a molecule. By combining 381
the utilization of NMR and IR spectroscopies, this study is able to gather sufficient evidence 382
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
19
on the chemical interactions between the bitumen and poly(lactic) acid (PLA). In NMR 383
analysis, different types of protons (H) are represented as peak signals in the spectrum having 384
different chemical shifts. The NMR of the control bitumen (Figure 2) shows that signals are 385
absorbed at a different range of chemical shift. The signals from 0.8 to 1.4 ppm in the region 386
(a) represent the protons from aliphatic alkanes. It can be concluded that most of the protons in 387
the base bitumen are alkanes, whether they are from the primary (R-CH3), secondary (R-CH2-388
R) or tertiary alkanes (R3CH). The two singlet peaks in this region indicate that these protons 389
are bonded with other functional groups (R), for instance, oxygen. The signals in the region (b) 390
are protons which represent alkenes, alkynes, aliphatic carbonyl functional group or protons 391
bonded with phenyl (aromatic as side chain). In addition, no other signals are observed in the 392
spectrums. This indicated the occurrence of other chemical shift (between 6.5 and 8.0 ppm) 393
which represented the aromatic protons. However, it is known that bitumen contains a lot of 394
aromatic compounds (Polacco et al., 2006), thus, it can be deduced that the aromatic group in 395
the bitumen is present as the phenyl group and no free protons are attached at the aromatic 396
structure. 397
398
The NMR spectrum of PLA (Figure 3) shows two signals, where one of the peaks is a 399
doublet, indicating the protons from the methyl group (assigned as c), and the second peak is a 400
quartet, which indicates the proton assigned as (d). Proton (d) is more shielded (appears at a 401
high chemical shift) compared to the methyl group and more electronegative when interacting 402
closely with two oxygen atoms next to each other. The results of NMR analysis of the bitumen 403
modified with 3, 5, 7 and 9% PLA (Figure 4) show that all signals from the bitumen and PLA 404
(a, b, c, and d) appear at each chemical shift. The increase in the observed intensity of the 405
signals for PLA corresponds with the increasing concentration of PLA in the samples. 406
However, the signals in the region (b) of the modified samples seem to be suppressed. The 407
suppression of the signals in this area indicates the loss of the proton absorbed at this chemical 408
shift. This is because one of the functional groups (either carbonyl groups or aliphatic 409
alkenes/alkynes) from this region interacts with PLA; this is later confirmed by the result of 410
the FT-IR analysis. 411
412
FT-IR analysis of the base bitumen, PLA and PLA modified bitumen (Figure 5) show 413
two additional bands at wavenumbers 1098.9 (region i) and 1749.9 cm-1 (region ii) and the 414
PLA-modified bitumen show a decrease in a band at 3600-3650 cm-1 relative to PLA. The new 415
functional groups in the PLA-modified bitumen sample (carbon-oxygen bonding (C-O) in 416
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
20
region i and carbonyl group (C=O) in region ii) support the result of NMR analysis. The 417
occurrence of new functional groups in the PLA-modified bitumen represented the PLA is 418
compatible with the base bitumen. The PLA and bitumen are chemically interacting with the 419
base bitumen during blending. The disappearance of the band in region iii, represented by the 420
hydroxyl group (OH), shows the reaction between the base bitumen and PLA occurring at the 421
OH group; this has resulted in the formation of new C-O and C=O bonding. However, the result 422
is not sufficient for predicting the functional group in the base bitumen reacting with the OH 423
group of the PLA. Thus, sequential dissolution was carried out to to determine the compatibility 424
of PLA with the bitumen. 425
426
The approach for investigating sequential dissolution was formulated by Corbett (1969) 427
and has been utilized by many researchers. Sequential dissolution is carried out to evaluate the 428
oxidation process that occurs between the binder and the bitumen. Generally, there is a net 429
reduction of maltenes fraction during an oxidation reaction, which occurs simultaneously with 430
an increase in asphaltene fraction. The formation of carbonyl functionalities within the binder 431
is linked with the increase in asphaltene during a sequential dissolution. Thus, an increase in 432
carbonyl functionalities is anticipated during the later stages of the extraction process when a 433
binder is being sequentially dissolved. In this study, sequential dissolution was used to 434
investigate the compatibility of PLA as a modifier for bitumen, thereby determining the 435
interaction of asphaltene with PLA. All samples (base bitumen and bitumen modified with 3, 436
5, 7 and 9% PLA) were washed with the same volume of chloroform (w/v). The result presented 437
in Figure 6 shows that the standard deviation does not exceed 1. The fractionation of the 438
bitumen modified with 3, 5 and 7% PLA with chloroform yielded 14.4 ± 0.8% asphaltenes, 439
slightly higher than the amount produced by the control bitumen (13.8 ± 0.2%). The lack of 440
significant difference in the value indicates absence of sequential dissolution and PLA in 441
concentrations of 3, 5 and 7% are compatible with the base bitumen. 442
443
The bitumen modified with 9% PLA show a ±5 % change in asphaltene content in 444
comparison to the control sample, indicating the compatibility of PLA with bitumen base does 445
not exceed 7%. A sufficient degree of polymer-bitumen compatibility is required to prevent 446
separation during storage, pumping and application of the asphalt mixture, as well as to ensure 447
required properties for pavements. Polymer modified bitumen with poor storage stability is not 448
suitable for applications such as paving binder, roofing, and other industrial speciality products 449
(Isacsson et al., 1995; Becker et al., 2001; Wahhab et al., 2016). The results of NMR and FTIR 450
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
21
are supported by the carbonyl index shown in Figure 6, where the carbonyl index is directly 451
proportional to the release of asphaltenes. It should be noted that the solvent used in this study, 452
i.e. chloroform, has never been reported to be one of the solvents with good compatibility with 453
bitumen. The amount of asphaltenes released due to the utilization of chloroform (13.8 ± 0.2%) 454
is lower than most of the solvents tested, such as TCE (16.7%), THF (22.5%), toluene (19.7%) 455
and decalin (22.6%) (Bowers et al. 2014). The low percentage of asphaltenes released by 456
chloroform is an indication of its high solubility. 457
458
FT-IR analysis of sequential dissolution was carried out to further investigate the 459
interaction between PLA and bitumen observed in the IR spectrum shown in Figure 5. The 460
washed (sequential dissolution) (WSD) and unwashed (PLA-modified bitumen) (UW) samples 461
were compared to determine the inter-correlation between the existing functional group and 462
the changes after blending. Based on the comparison of the washed and unwashed samples, it 463
can be concluded that the interaction bond between asphaltenes and PLA is dependent on the 464
carbonyl functionalities index. There is a different index pattern shown in addition to the band 465
at region i (C-O) and region ii (C=O) when divided with C=C and C-C bonds (Figure 5). 466
Overall, the C=C bond decreases while the C-C bond remains unchanged in the UW samples 467
of the control bitumen and the PLA modified bitumen. However, an increase in both the C=C 468
and C-C bonds was observed in all WSD in comparison to the control bitumen. The increase 469
in the amount of both alkenes and alkanes in the WSD is expected since both are a part of 470
asphaltene, which is the product of sequential dissolution. The difference in the number of 471
alkenes and alkanes in the UW indicates that one of them is probably involved in the chemical 472
interaction between the bitumen and the PLA. 473
474
From the analysis of the C-O bond in region i, the 11.2% increase in the cumulative 475
index of C-O with C=C relative to the control compared with the 2.5% decrease in that for C-476
O with C-C indicated the C-O bond formed in the PLA modified bitumen samples is related 477
to the C=C interaction. This data is supported by the result of the WSD analysis, the index for 478
C-O with C=C values remains unchanged (except for 9% PLA) while the C-O shows a decrease 479
when divided with C-C area. The same index value for C-O with C-C in the WSD indicate that 480
no C-O bond is detected in PLA because of its high compatibility with bitumen after the 481
extraction process for sequential dissolution evaluation. Analysis of the carbonyl in region ii 482
shows that the decrease in the carbonyl index of the WSD corresponds with the amount of 483
asphaltenes dissolved in chloroform. The difference in the values of both carbonyl index 484
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
22
between C=C (average, 15.1%) and C-C (average, 4.4%) in all PLA-modified bitumen samples 485
is due to the significantly low C=C content in the samples after modification. Based on these 486
values, it can be concluded that the interaction of bitumen with PLA is between C=C and not 487
C-C. The result of NMR analysis (Figure 4B) supports this conclusion since there is a 488
suppression of signals at a chemical shift of between 1.5 and 3.5 ppm; these signals represent 489
the alkene (C=C) group. Finally, the loss of OH group in region iii (Figure 5) in the PLA-490
modified bitumen samples seems to indicate the following reaction mechanism between PLA 491
and bitumen (Figure 13). 492
493
HO
CH3
O
O CH3
O
O CH3
OH
O
H
n
Asphaltene
C C
H
H
Asphaltene
C C
H
Asphaltene
Asphaltene
H
Asphaltene
C C
H
H
Asphaltene
C C
H
Asphaltene
Asphaltene
H
O
CH3
O
O CH3
O
O CH3
O
O
H
n
Asphaltene
C
Asphaltene
CH3
C
Asphaltene
AsphalteneCH3
O
CH3
O
O CH3
O
O CH3
O
O
H
n
HH
PLA
494
495
Figure 13: Proposed reaction mechanism between PLA and bitumen 496
497
Generally, all the supporting data from NMR and FT-IR suggest that the reaction 498
between PLA and bitumen is an addition reaction. This reaction occurred when the hydroxyl 499
group of PLA reacts with the alkenes in bitumen, where the formation of bridge C-O bonding 500
found in the region based on FT-IR analysis. The finding is supported by the previous studies, 501
indicating the certain chemical reactions between the functional groups of the components of 502
the blends. This reaction or chemical compatibilization creates in-situ copolymers formation 503
during processing (Polacco et al., 2015; Mancini et al., 1991). This proposed mechanism is 504
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
23
important since the structure of PLA has high compatibility with bitumen. The finding of new 505
mechanism potentially provided the fundamental information related to the chemical 506
interaction of PLA and bitumen which lead to the discovery of new modifiers that are better 507
bitumen enhancer. 508
509
In addition to FT-IR analysis to determine the compatibility of PLA with bitumen, the 510
dispersity of PLA throughout the base bitumen was also examined with Gel Permeation 511
Chromatography (GPC). GPC was used to determine the molecular weight average of PLA 512
modified bitumen. The profile of GPC varies between bitumen modified with 3, 5, 7 and 9% 513
PLA relative to the control bitumen. It is worth noting that the peak eluted at ± 25.1 minutes, 514
differentiates the bitumen from the bitumen-PLA samples. The molecular properties of this 515
peak are presented in Table 2, and it shows a decline in the number of MP. The Mw, Mn and 516
polydispersity index of the samples were compared to the control sample. Mn is the statistical 517
average molecular weight of all PLA chains in the sample. Unlike Mn, Mw takes into account 518
the molecular weight of a chain in determining its contributions to the average molecular 519
weight. 520
521
Figure 10 and Table 2 show that there is a significant difference in bitumen modified 522
with 5% PLA (1456 gmol-1) and 7% PLA (2161 gmol-1). The heavier the chains have more 523
contribution to Mw; therefore, a better PLA-bitumen interaction is observed with 7% PLA 524
modification as compared to 3 and 5%. Polydispersity index is a measure of the distribution of 525
PLA’s molecular weight in the samples and is defined as Mw/Mn. The large polydispersity 526
index indicates the broad distribution of molecular weight. The difference in polydispersity 527
index of 5% (1.136) and 7% (1.653) PLA modification indicates that the bitumen showed the 528
best chemical interaction with the incorporation of up to 7% PLA. However, from the data of 529
sequential dissolution, the 9% PLA showed a sequential dissolution effect resulting in reduced 530
compatibility. In summary, based on the GPC and sequential dissolution data, the best 531
modification of bitumen is achieved with 7% PLA. This result is supported by the 532
characterization of the physical performance of PLA-modified bitumen. This research shows 533
that the properties of modified bitumen with 7% of PLA is the good quality in terms of 534
hardness, stiffness, ductility and storage stability ability. This is consistent with the previous 535
discussion of the chemical interaction, compatibility and dispersity test. 536
537
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
24
4. Conclusions and Suggestion for Future Study 538
539
This study aims to comprehensively evaluate the chemical and physical properties of PLA 540
modified bitumen. The chemical properties were monitored using NMR, FTIR and GPC, while 541
the physical properties of modified bitumen were measured by several empirical indexes in 542
terms of penetration, softening point and ductility grading. Furthermore, the storage stability 543
of the modified bitumen was also investigated in this study. The main conclusions of this 544
research are: 545
The addition of PLA into the base bitumen indicates the existence of chemical 546
interaction between these materials. The findings of this study have shown the 547
chemically cross-link at the alkene group (C=O) of PLA and hydroxyl group (OH) of 548
bitumen. 549
The results from GPC analysis shows high compatibility between the bitumen and 550
PLA. The dispersion of PLA in the bitumen is found to be directly proportional with 551
the amount of PLA, which results in the enhanced molecular properties of the PLA-552
modified bitumen. 553
The physical properties of PLA modified bitumen obtained from the conventional 554
bitumen tests show that the consistency of modified bitumen has increased as 555
compared to the base bitumen with the low penetration and high softening point value. 556
Also, ductility properties of modified bitumen indicate the permitted value as that of 557
base bitumen. 558
The modification of bitumen with up to 7% PLA is storage stable except for the 559
modified bitumen with 9% of PLA content. 560
In summary, the use of PLA in bitumen modification has a significant effect on the 561
chemical and physical properties of modified bitumen. Based on the results, 7% PLA 562
is recommended as the optimum amount for modifying base bitumen. 563
For future studies, a more comprehensive characterization of PLA modified bitumen for 564
rheology properties can be carried out. There is a need to investigate the ageing of the PLA 565
modified bitumen for the effect of oxidation and UV radiation on the rheological properties 566
and the potential deterioration over time. Moreover, further research is recommended to 567
investigate the application of PLA-modified bitumen in asphalt mixtures. 568
569
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
25
Acknowledgement 570
571
The authors would like to express their gratitude to Universiti Kebangsaan Malaysia (UKM) 572
for the financial support of this work (DIP-2020-003). 573
574
Conflicts of Interest Statement 575
576
The authors declare that there is no conflict of interest in the publication of this paper. 577
578
References 579
580
A. A. Kadhim, H. M. K. Al-Mutairee. An Experimental Study on Behavior of Sustainable 581
Rubberized Concrete Mixes. Civil Engineering Journal. 6(7) (2020) 1273-1285. Doi: 582
10.28991/cej-2020-03091547 583
A. M. Shihab et al. Effects of Temperature in Different Initial Duration Time for Soft Clay 584
Stabilized by Fly Ash Based Geopolymer. Civil Engineering Journal. 4(9) (2018) 2082-585
2096. Doi: 10.28991/cej-03091141 586
A. Schaur, S. Unterberger, R. Lackner, Impact of molecular structure of SBS on 587
thermomechanical properties of polymer modified bitumen, Eur. Polym. J. 96 (2017) 588
256–265. Doi: 10.1016/j.eurpolymj.2017.09.017 589
A.N.H. Ibrahim et al. Physical Properties and Storage Stability of Geopolymer Modified 590
Asphalt Binder. Jurnal Teknologi (Sciences and Engineering). 78(7–2) (2016) 133–591
138. Doi: 10.11113/jt.v78.9508 592
A.N.H. Ibrahim et al. Sifat Mekanik dan Tingkah Laku Resapan Air Bitumen Terubahsuai 593
Geopolimer. Jurnal Teknologi (Science & Engineering). 4 (2017) 107–111. Doi: 594
10.11113/jt.v79.9828 595
ASTM-D113, American Society for Testing and Materials, Standard Test Method for Ductility 596
of Bituminous Materials, Conshohocken, Pennsylvania, USA, 1999. Doi: 597
10.1520/d0113 598
ASTM-D36, American Society for Testing and Materials, Standard Test Method for Softening 599
Point of Bitumen (Ring-and-Ball Apparatus), Conshohocken, Pennsylvania, USA, 600
1995. Doi: 10.1520/d0036_d0036m 601
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
26
ASTM-D5, American Society for Testing and Materials, Standard Test Method for Penetration 602
of Bituminous Materials, Conshohocken, Pennsylvania, USA, 1997. Doi: 603
10.1520/d0005_d0005m 604
B. Sengoz, A. Topal, G. Isikyakar, Morphology and image analysis of polymer modified 605
bitumens, Constr. Build. Mater. 23 (5) (2009) 1986–1992. Doi: 606
10.1016/j.conbuildmat.2008.08.020 607
C. Giavarini et al., Production of stable polypropylene-modified bitumens, Fuel 75 (6) (1996) 608
681–686. Doi: 10.1016/0016-2361(95)00312-6 609
C. Loderer et al. Effect of crumb rubber production technology on performance of modified 610
bitumen. Constr. Build. Mater. 191 (2018) 1159–1171. Doi: 611
10.1016/j.conbuildmat.2018.10.046 612
D. Lesueur, The colloidal structure of bitumen: consequences on the rheology and on the 613
mechanisms of bitumen modification, Adv. Colloid Interface Sci. 145 (2019) 42–82. 614
Doi: 10.1016/j.cis.2008.08.011 615
F. Cardone et al. Influence of polymer modification on asphalt binder dynamic and steady flow 616
viscosities. Constr. Build. Mater. 71 (2014) 435–443. Doi: 617
10.1016/j.conbuildmat.2014.08.043 618
G. Mancini, P. ltalia, Method for preparing stable bitumen-polymer mixtures, EP 0 458386 A1, 619
1991 620
G. Polacco et al. A review of the fundamentals of polymer-modified asphalts: Asphalt/polymer 621
interactions and principles of compatibility. Advances in Colloid and Interface Science. 622
224 (2015) 72–112. Doi: 10.1016/j.cis.2015.07.010 623
G. Polacco et al. Relation between polymer architecture and nonlinear viscoelastic behavior of 624
modified asphalts, Current Opinions in Colloid and Interface Science. 11 (2006) 230-625
245. Doi: 10.1016/j.cocis.2006.09.001 626
G. Polacco et al., Asphalt modification with different polyethylene-based polymers, Eur. 627
Polym. J. 41 (12) (2005) 2831–2844. Doi: 10.1016/j.eurpolymj.2005.05.034 628
G.D. Airey, Styrene butadiene styrene polymer modification of road bitumens, J. Mater. Sci. 629
39 (2004) 951–959. Doi: 10.1023/b:jmsc.0000012927.00747.83 630
H. T. Nhabih et al. Study a Structural Behavior of Eccentrically Loaded GFRP Reinforced 631
Columns Made of Geopolymer Concrete. Civil Engineering Journal. 6(3) (2020) 563-632
575. Doi: 10.28991/cej-2020-03091492 633
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
27
H. Wang et al. Experimental characterization of storage stability of crumb rubber modified 634
bitumen with warm-mix additives. Constr. Build. Mater. 249 (2020a) 118840. Doi: 635
10.1016/j.conbuildmat.2020.118840 636
H. Wang et al. Experimental characterization of storage stability of crumb rubber modified 637
bitumen with warm-mix additives. Constr. Build. Mater. 249 (2020) 118840. Doi: 638
10.1016/j.conbuildmat.2020.118840 639
H. Wang et al. Fatigue performance of long-term aged crumb rubber modified bitumen 640
containing warm-mix additives. Constr. Build. Mater. 239 (2020b) 117824. Doi: 641
10.1016/j.conbuildmat.2019.117824. 642
H. Wang et al. Micromechanical modelling of complex shear modulus of crumb rubber 643
modified bitumen. Mater Des. 188 (2020c) 108467. Doi: 644
10.1016/j.matdes.2019.108467 645
H.A. Omar et al., Determining the water damage resistance of nano-clay modified bitumens 646
using the indirect tensile strength and surface free energy methods. Construction and 647
Building Materials 167 (2018) 391-402. Doi: 648
doi.org/10.1016/j.conbuildmat.2018.02.011 649
H.I.A. Wahhab, M.A. Dalhat, M.A. Habib. Storage stability and high-temperature performance 650
of asphalt binder modified with recycled plastic. Road Mater. Pavement. 18 651
(2016)1117–1134. Doi: 10.1080/14680629.2016.1207554 652
J. Zhu, B. Birgisson, N. Kringos. Polymer modification of bitumen: Advances and challenges. 653
European Polymer Journal. 54 (2014) 18-38. Doi: 10.1016/j.eurpolymj.2014.02.005. 654
J.S. Chen, C.C. Huang, Fundamental characterization of SBS-modified asphalt mixed with 655
sulfur, J. Appl. Polym. Sci. 103 (2007) 2817–2825. Doi: 10.1002/app.24621 656
L. Brasileiro et al. Reclaimed Polymers as Asphalt Binder Modifiers for More Sustainable 657
Roads: A Review. Sustainability 11 (2019) 646. Doi: 10.3390/su11030646 658
L.G.A.T. Farias et al. Effects of nanoclay and nanocomposites on bitumen rheological 659
properties. Construction and Building Materials. 125 (2016) 873–883. Doi: 660
10.1016/j.conbuildmat.2016.08.127 661
L.W. Corbett. Composition of asphalt based on generic fractionation using solvent 662
deasphalteneing, elution-adsorption chromatography and deniometric characterization. 663
Analytical chemistry. 41(4) (1969) 576-579. Doi: 10.1021/ac60273a004 664
M. Iqbal et al. Improving the Aging Resistance of Asphalt by Addition of Polyethylene and 665
Sulphur. Civil Engineering Journal. 6(5) (2020) 1017-1030. Doi: 10.28991/cej-2020-666
03091525 667
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
28
M. Mohammadiroudbari et al. Effect of nanoclay on the morphology of polyethylene modified 668
bitumen. Construction and Building Materials. 116 (2016) 245-251. Doi: 669
10.1016/j.conbuildmat.2016.04.098 670
M. Panda, M. Mazumdar, Engineering properties of EVA-modified bitumen binder for paving 671
mixes, J. Mater. Civ. Eng. 11 (2) (1999) 131–137. Doi: 10.1061/(asce)0899-672
1561(1999)11:2(131) 673
M.F. Navarro et al. Structural analysis of polymer modified bituminous materials in the 674
rehabilitation of light-medium traffic volume roads. Constr. Build. Mater. 156 675
(2017)621–631. Doi: 10.1016/j.conbuildmat.2017.09.006 676
M.S. Gardiner, D.E. Newcomb. Polymer literature review. St. Paul, Minnesota: Minnesota 677
Department of Transportation. 95 (1995) 27. 678
N.I.M. Yusoff et al. The effects of moisture susceptibility and ageing conditions on nano-679
silica/polymer-modified asphalt mixtures. Construction and Building Materials. 72 680
(2014) 139-147. Doi: 10.1016/j.conbuildmat.2014.09.014 681
N.I.M. Yusoff et al., Engineering characteristics of nanosilica/polymer-modified bitumen and 682
predicting their rheological properties using multilayer perceptron neural network 683
model. Construction and Building Materials. 204 (2019) 781-799. Doi: 684
10.1016/j.conbuildmat.2019.01.203 685
N.M. Zakaria et al. The use of mixed waste recycled plastic and glass as an aggregate 686
replacement in asphalt mixtures. Jurnal Teknologi (Science & Engineering). 80(1) 687
(2018) 79–88. Doi: 10.11113/jt.v80.11147 688
O. V. Laukkanen et al. Low-temperature rheological and morphological characterization of 689
SBS modified bitumen. Constr. Build. Mater. 179 (2018) 348–359. Doi: 690
10.1016/j.conbuildmat.2018.05.160 691
R. A. Al-Mansob et al. Physical and rheological properties of epoxidized natural rubber 692
modified bitumens. Constr. Build. Mater. 63 (2014) 242–248. Doi: 693
10.1016/j.conbuildmat.2014.04.026 694
R. Auras, B. Harte, S. Selke. An overview of polylactides as packaging materials. Macromol 695
Biosci.4 (2004)835–864. Doi: 10.1002/mabi.200400043 696
R. Yu et al. Storage stability and rheological properties of asphalt modified with waste 697
packaging polyethylene and organic montmorillonite. Applied Clay Science. 104 698
(2015) 1–7. Doi: 10.1016/j.clay.2014.11.033 699
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
29
R.K. Padhan, A.A. Gupta, Preparation and evaluation of waste PET derived polyurethane 700
polymer-modified bitumen through in situ polymerization reaction, Constr. Build. 701
Mater. 158 (2018) 337–345. Doi: 10.1016/j.conbuildmat.2017.09.147 702
R.M. Rasal, A.V. Janorkar, D.E. Hirt. Poly(lactic acid) modifications. Prog Polym Sci. 35 703
(2010) 338–356. 704
S. Hosseinnezhad, S.F. Kabir, D. Oldham, M. Mousavi, E.H. Fini, Surface functionalization of 705
rubber particles to reduce phase separation in rubberized asphalt for sustainable 706
construction, J. Cleaner Prod. 225 (2019) 82–89. Doi: 10.1016/j.jclepro.2019.03.219 707
S. Poovaneshvaran et al. Impacts of recycled crumb rubber powder and natural rubber latex on 708
the modified asphalt rheological behaviour, bonding, and resistance to shear. Constr. 709
Build. Mater. 234 (2020) 117357. Doi: 10.1016/j.conbuildmat.2019.117357 710
S. Saedi, S. Oruc. The Effects of Nano Bentonite and Fatty Arbocel on Improving the Behavior 711
of Warm Mixture Asphalt against Moisture Damage and Rutting. Civil Engineering 712
Journal. 6(5) (2020) 877-888. Doi: 10.28991/cej-2020-03091514 713
S.A.P. Rosyidi et al. Investigation of the chemical, strength, adhesion and morphological 714
properties of fly ash based geopolymer-modified bitumen. Constr. Build. Mater. 255 715
(2020) 119364. Doi: 10.1016/j.conbuildmat.2020.119364 716
S.I.A. Ali et al. Physical and rheological properties of acrylate–styrene–acrylonitrile modified 717
asphalt cement. Constr. Build. Mater. 93 (2015) 326–334. Doi: 718
10.1016/j.conbuildmat.2015.05.016 719
S.T. Alata, M. Yilmaz. Effects of different polymers on mechanical properties of bituminous 720
binders and hot mixtures. Constr. Build. Mater. 42 (2013) 161–167. Doi: 721
10.1016/j.conbuildmat.2013.01.027 722
T. Günay, P. Ahmedzade. Physical and rheological properties of nano-TiO2 and 723
nanocomposite modified bitumens. Constr. Build. Mater. 243 (2020) 118208. Doi: 724
10.1016/j.conbuildmat.2020.118208 725
Trang et al. The Study of Dynamics Heterogeneity in SiO2 Liquid. HighTech and Innovation 726
Journal. 1(1) (2020) 1273-1285. Doi: 10.28991/HIJ-2020-01-01-01 727
U. Isacsson, X. Lu, Testing and appraisal of polymer modified road bitumens - state of the art, 728
Materials and Structures.28 (1995) 139-159. Doi: 10.1007/bf02473221 729
Y. Becker, M.P. Méndez, Y. Rodríguez. Polymer modified asphalt. Vis. Tecnol. 9 (2001) 39–730
50. 731
Z. Jiang et al. Evaluation of new aspect of styrene-butadiene-styrene modified bitumens: 732
Damping property and mechanism. Constr. Build. Mater. 242 (2020) 118185. Doi: 733
10.1016/j.conbuildmat.2020.118185 734
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
30
Z. Yao et al. Integrated utilization of recycled crumb rubber and polyethylene for enhancing 735
the performance of modified bitumen. Constr. Build. Mater. 170 (2018) 217–224. Doi: 736
10.1016/j.conbuildmat.2018.03.080 737
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
AUTHOR BIOGRAPHY
Nashriq Jailaini is a research assistant at the Department of Civil Engineering, Universiti
Kebangsaan Malaysia (UKM), Malaysia. His research interests are mainly in the area of
pavement engineering and pavement materials.
Ahmad Nazrul Hakimi Ibrahim is a PhD student at the Department of Civil Engineering,
Universiti Kebangsaan Malaysia (UKM), Malaysia. His research interests are mainly in the area
of highway and transportation engineering.
Dr. Abdur Rahim is a senior lecturer in the Department of Transportation Engineering and
Management, University of Engineering and Technology, Lahore, Pakistan. His research
interests are mainly in the area of pavement engineering and pavement materials.
Ir. Dr. Ahmad Kamil Arshad is a professor in the Institute for Infrastructure Engineering and
Sustainable Management, Universiti Teknologi MARA (UiTM), Shah Alam, Malaysia. His
research interests are mainly in the area of pavement engineering and pavement materials.
Ts. Dr. Norhidayah Abdul Hassan is a senior lecturer in the School of Civil Engineering,
Universiti Teknologi Malaysia (UTM), Malaysia. Her research interests are mainly in the area
of pavement engineering and pavement materials.
Ir. Dr. Nur Izzi Md. Yusoff is an associate professor in the Department of Civil Engineering,
Universiti Kebangsaan Malaysia (UKM), Malaysia. His research interests are mainly in the area
of pavement engineering and pavement materials.
Author Biography
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65