Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
1.0.01
AEROSOL VALVES
Aerosol valves are devices that release products in spray mode from containers under pressure.
The most common applications are in the packaging of personal deodorants, hair sprays, insecticides, household and food products, decoration and technical products.
Most of the aerosol valves are continuous spray mode. Metered dose aerosol valves are used for specific applications, particularly in the pharmaceutical sector.
Coster production covers a complete range of aerosol valves that can meet any market requirement.
All dimensional specifications in the catalogue should be considered only for reference use.
revision: 0 30/09/2002
COSTER
1.0.02
A
D
E
VISI
BLE
MFB
OC LPS
B
VISI
BLE
D
LPS
DETERMININGDIP TUBE LENGTH
For the 1” valves the length LPS of the dip tube is determined according to the dimension A of the container: LPS = A - Y . Y depends on the kind of container employed (thickness of the material, rim, diameter and curving radius of the container bottom, etc.).For the containers with flat bottom, Y = 0.
CONTAINER CONTAINER Y MATERIAL DIAMETER mm Tin plate 45 mm 3 Tin plate > 45 mm 7 Aluminium < 45 mm 2 Aluminium 45 to 55 mm 3 Aluminium > 55 mm 5
The length MFBOC (Measured From Bottom Of Cup) is: MFBOC = LPS - E .The length VISIBLE is:VISIBLE = LPS - D .The measures D and E vary according to the valve model.
For 20 mm or smaller diameter valves, the length LPS of the dip tube is determined according to the dimension B of the container (right).The length VISIBLE is:VISIBLE = LPS - D .The measure D varies according to the valve model.The length must be modified according to different container diameters and forms.
revision: 0 30/09/2002
COSTER
1.7.03
20N
HOUSING
STEM Ø 2.8 mm
revision: 6 30/04/2013
STEM
INTERNAL GASKET
EXTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
CONTINUOUS VALVE
DIP TUBE
MOUNTING CUP DIMENSIONS
H
MOUNTING CUP MATERIAL PROTECTION Aluminium Plain Silver anodized Gold anodized
EXTERNAL GASKET MATERIAL Buna
INTERNAL GASKET MATERIAL Neoprene Buna Chlorobutyl Butyl
SPRING MATERIAL Stainless steel AISI 302
Valve with 15, 18 or 20 mm mounting cup, to be used in the upright position.
The dip tube is capillary, and it is inserted inside the mounting tang.
Designed for perfumes, cosmetics and pharmaceutical products.
HOUSING MATERIAL Polyethylene HD (HDPE)
STEM MATERIAL Acetalic resin (POM)
DIP TUBE MATERIAL Polyethylene LD (LDPE)
MOUNTING CUP DIMENSIONS
Ø ØA mounting cup height (H) in mm nominal mm / 0 / 1 / 2
15 15.40 6.60 7.60
18 18.65 6.60 7.60
20 20.20 6.60 7.60
Ø 0.5 mm
Ø A
Ø 6.8 mm
COSTER
1.7.04
20N
50
40
30
20
20N valves must be filled before the assembling of the actuator.
The filling speed refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components.
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
STANDARD ACTUATORS
FILLING DIAGRAM AND FILLING SPEED GRAPH
revision: 6 30/04/2013
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure
10 20 30 40 50 60 70 80 90
V05.1233: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1245: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1253: with micromist insert.
V05.1471: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1405: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1492: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.31: foaming actuator.
V05.6: directional actuator.
V05.27: with HD polyethylene V07.9/L tube, supplied unfitted. Tube length (L) on request.
V05.26 + V06.1/L: with mounted stainless steel tube AISI 304, for dental use.
V05.1278: with micromist insert.
V05.26 + V06.1/L
V05.1233 V05.1253V05.1245
V05.31
V05.1278
V05.1471
V05.1492
V05.1405
5.5 mm
V05.6 V05.27
COSTER
1.7.05
20D
HOUSING
STEM Ø 2.8 mm
revision: 830/04/2013
MOUNTING CUP MATERIAL PROTECTION Aluminium Plain Silver anodized Gold anodized
EXTERNAL GASKET MATERIAL Buna
INTERNAL GASKET MATERIAL Neoprene Buna Chlorobutyl ButylSPRING MATERIAL OPTIONS Stainless steel AISI 302 soft on request
METERED DOSE VALVE
Metered dose valve with 15, 18 or 20 mm mounting cup, to be used in the upright position.
The dip tube is semi-capillary, and it is inserted inside the mounting tang.
Designed for perfumes, cosmetics and pharmaceutical products.
Quantity metered: 50, 75, 100, 120, 150 µl.
STEM
INTERNAL GASKET
EXTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
DIP TUBE MATERIAL Polyethylene HD (HDPE)
MOUNTING CUP DIMENSIONS
H
STEM MATERIAL Acetalic resin (POM)
HOUSING MATERIAL Polyethylene HD (HDPE) MOUNTING CUP DIMENSIONS
Ø ØA mounting cup height (H) in mm nominal mm / 0 / 1 / 2
15 15.40 6.60 7.60
18 18.65 6.60 7.60
20 20.20 6.60 7.60
Ø 0.5 mm
Ø A
Ø 6.8 mm
COLOURING HOUSING VALVE
DOSAGE COLOUR
50 µl neutral
75 µl yellow
100 µl azure
120 µl pink
150 µl black
COSTER
1.7.06
20D
50
40
30
20
20D valves must be filled before the assembling of the actuator.
The filling speed refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components.
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
STANDARD ACTUATORS
FILLING DIAGRAM AND FILLING SPEED GRAPH
revision: 8 30/04/2013
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure
10 20 30 40 50 60 70 80 90
V05.1271: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1233: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1245: with micromist insert. Gold or silver coloured metal sheathing on request.
V05.1253: with micromist insert.
V05.6: directional actuator.
V05.497: nasal actuator without micromist insert, with cap V16.46.
V05.26 + V06.1/L: with mounted stainless steel tube AISI 304, for dental use.
V05.29: foaming actuator only for D valves.
V05.27: with HD polyethylene V07.9/L tube, supplied unfitted. Tube length (L) on request.
V05.1271 V05.1245V05.1233
V05.26 + V06.1/LV05.497
V05.1253
5.5 mm
V05.6
V05.27
V05.29
CORPO
STELO Ø 3,9 mm
revisione: 0 30/09/2002
VALVOLA AD EROGAZIONE CONTINUA
COSTER
1.7.11
20K
HOUSING
STEM Ø 3.9 mm
revision: 4 15/02/2015
STEM
INTERNAL GASKET
EXTERNAL GASKET
DIP TUBE
MOUNTING CUP
SPRING
CONTINUOUS VALVE
Valve for upright use, with 20 mm mounting cup.
The valve is equipped with a standard housing, without the additional gas orifice (VPH).
The dip tube is mounted outside the housing tang.
The valve must be used in the upright position.
HOUSING
MOUNTING CUP MATERIAL PROTECTION Aluminium Plain Silver anodized Gold anodized
EXTERNAL GASKET MATERIAL Buna
INTERNAL GASKET MATERIAL Neoprene Buna Chlorobutyl Butyl
SPRING MATERIAL OPTIONS Stainless steel AISI 302 soft on request (only for buna internal gasket)
HOUSING MATERIAL OPTIONS Polyethylene HD (HDPE) Acetalic resin (POM)
DIP TUBE MATERIAL Polyethylene LD (LDPE)
STEM MATERIAL OPTIONS Acetalic resin (POM) Polyethylene HD (HDPE)
OrificeOrifice
STEM ORIFICES
N° orifices & Ø (mm)
POM HDPE NOTE
1 x 0.27 • •
1 x 0.30 • •
1 x 0.35 • •
1 x 0.40 • •
1 x 0.50 • •
1 x 0.50 • for powders
1 x 0.60 • •
1 x 0.60 • • for powders
1 x 0.65 •
2 x 0.50 • •
2 x 0.50 • for powders
4 x 0.50 • •
Ø 8.4 mm
FOR POWDERSSTANDARD
COSTER
1.7.12
20K
STANDARD ACTUATORS
FILLING DIAGRAMS AND FILLING SPEED GRAPH
revision: 4 15/02/2015
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure
100 125 150 175 200 225 250 275
13 mm18.5 mm
60
50
40
30
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (shape of the stem, number and diameter of the orifices on the stem).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
12.5 mm7 mm
SERIES 1300: versions without insert, with micromist insert, with directional insert, with tube holding insert and with special inserts. Can be supplied mounted on the valve.
V05.2480: nasal spray actuatorfor pharmaceutical products.Supplied unfitted.
V05.1440: with micromist insert. With gold or silver anodized metal sheathing on request.Can be supplied mounted on the valve. V04.1443: actuator with special insert for creams and lotions. Supplied unfitted.This actuator cannot be used with an overcap fitted on the mounting cup.
SERIES 1300 V05.2480 V05.1440 V04.1443
COSTER
1.1.11
NKR
STEM MATERIAL OPTIONS Acetalic resin (POM) Polyethylene HD (HDPE)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium Internal Micoflex / External Gold lacqueredClear lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIAL OPTIONSNeoprene, Buna, Viton on requestChlorobutyl or Butyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 Stainless steel AISI 316
HOUSING MATERIAL Polyethylene HD (HDPE)
HOUSING
STEM Ø 3.9 mm
revision: 0 30/04/2013
STEM
EXTERNAL GASKET
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
SHORT STROKE CONTINUOUS VALVE FOR UPSIDE DOWN USE
The NKR valve, with reduced stroke and spring, is equipped with a housing with two side slots,that permits the complete emptying of the can in the upside-down position.The valve does not need a dip tube. Nevertheless, the housing is supplied with a tang where a dip tube can be inserted in order to facilitate the selection of the valves in the automatic feeding machine.NKR valves are generally employed for products that must be actuated in upside-down position,such as hair mousse, cosmetic creams, food products, road markings paints, etc.
STEM ORIFICES
N° orifices & Ø (mm) POM HDPE NOTE
1 x 0.27 • •
1 x 0.30 • •
1 x 0.35 • •
1 x 0.40 • •
1 x 0.50 • •
1 x 0.60 • •
1 x 0.65 •
2 x 0.50 • •
4 x 0.50 • •
STANDARD
Orifice
COSTER
1.1.12
NKR
60
50
40
30
The filling speed graph refers to butane-propane propellant. It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (shape of the stem, number and diameter of the orifices). Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
STANDARD ACTUATORS
V05.938: actuator for whipped cream.
V05.988: foaming actuator.
V05.990: foaming actuator.
V05.1984: with fan spray, typical for household products or technical foam products.
revision: 0 30/04/2013
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
100 125 150 175 200 225 250 275
V05.990V05.988V05.938 V05.1984
7.8 mm *
For these valves the mechanicalopening of the stem is necessary.
(*): Suggested dimension that must assure mechanical opening 1.5 ± 0.3.
FILLING METHODS AND FILLING SPEED GRAPH
COSTER
1.3.03
NKE
�� ��
HOUSING
STEM Ø 3.3 mm
revision: 0 30/04/2013
SHORT STROKE CONTINUOUS VALVE
The NKE valve with reduced stroke and spring, is equipped with Eurostem and a standard housing,without additional gas orifice (VPH).
The dip tube is inserted outside the housing tang.
The valve must be used in upright position.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
EXTERNAL GASKET
FOR POWDERSSTANDARD
Orifice Orifice
STEM ORIFICES
N° orifices& Ø (mm) POM HDPE NOTE
1 x 0.30 •1 x 0.32 •1 x 0.35 •1 x 0.40 • •1 x 0.45 •1 x 0.50 •1 x 0.55 •1 x 0.60 •2 x 0.50 • •2 x 0.50 • for powders4 x 0.50 • •
STEM MATERIAL OPTIONS Acetalic resin (POM) Polyethylene HD (HDPE)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium Internal Micoflex / External Gold lacqueredClear lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIAL OPTIONSNeoprene, Buna, Viton on requestChlorobutyl or Butyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 Stainless steel AISI 316
HOUSING MATERIAL Polyethylene HD (HDPE)
DIP TUBE MATERIAL Polyethylene LD (LDPE)
COSTER
1.3.04
NKE
60
50
40
30
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (shape of the stem, number and diameter of the orifices).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
STANDARD ACTUATORS
FILLING METHODS AND FILLING SPEED GRAPH
revision: 0 30/04/2013
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
100 125 150 175 200 225 250 275
5.95 mm *
The short stroke eurostem valves are mainly chosen to fit customized actuators and spray caps, therefore only a limited range of standard actuators models is available.
V05.1771: versions with micromist insert.
V05.1770: versions with directional insert, and with extension.
V05.1871: with micromist insert.
V05.1873: with directional insert.
V05.893: foaming actuator.
V18.62: single piece vertical spray cap, designed for ø 52 necked-in tin plate cans. No micromist insert is needed.
V05.1771 V05.1770 V05.1873V05.1871
V05.893 V18.62
For these valves the mechanicalopening of the stem is necessary.
(*): Suggested dimension that must assure mechanical opening 1.5 ± 0.3.
COSTER
1.4.03
KEN
HOUSING
STEM Ø 3.3 mm
revision: 4 30/04/2013
SOFT TOUCH CONTINUOUS VALVE
Short stroke valve with reduced opening force. This function is made possible by a special stem (diameter 3.3 mm Eurostem) manufactured in two pieces.
A standard housing is utilized.
The dip tube is mounted outside the housing tang.
It functions only in the upright position.
STEM
INTERNAL GASKET
MOUNTING CUP
STEM BASE
SPRING
HOUSING
EXTERNAL GASKET
DIP TUBEOrifice
STEM ORIFICES
N° orifices & Ø (mm)
1 x 0.27 1 x 0.30 1 x 0.40 1 x 0.50 1 x 0.60
STEM / STEM BASE MATERIAL Acetalic resin (POM)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coatedAluminium Micoflex
Clear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 Soft on request (only for Buna internal gasket)
HOUSING MATERIAL OPTIONSPolyethylene HD (HDPE) Acetalic resin (POM)
DIP TUBE MATERIAL Polyethylene LD (LDPE)
COSTER
1.4.04
KEN
V05.1771 V05.1871 V05.893 V18.62V05.1873
60
50
40
30
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (diameter of the orifice on the stem).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
STANDARD ACTUATORS
FILLING DIAGRAM AND FILLING SPEED GRAPH
revision: 4 30/04/2013
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
100 125 150 175 200 225 250 275
5.5 mm
Soft touch valves are different from the standard valves because only a short stroke with reduced opening force is necessary to open them.
Due to the reduced opening force, the valve has an increased sensitivity and ease of actuation.
Soft touch valves are mainly utilized in special applications; therefore only a limited range of standard actuator models is available.
V05.1771: versions with micromist insert, with directional insert, and with extension.
V05.1871: with micromist insert.
V05.1873: with directional insert.
V05.893: foaming actuator.
V18.62: single piece vertical spray cap, designed for ø 52 necked-in tin plate cans. No micromist insert is needed.
COSTER
1.5.03
KSL
HOUSING
STEM Ø 3.9 mm
revision: 6 30/04/2013
CONTINUOUS VALVE
The valve is equipped with a housing in which the gas orifices VPH (Venturi system) and the product orifice RTP can be of various dimensions. The dip tube is semi-capillary, and it is inserted inside the mounting tang.
KSL valves are generally employed for water-based products filled with liquid gas (LPG) or for highly inflammable products. In this case the orifices dimensions, selected according to the gaseous or liquid phase, guarantee a perfect atomization of particles, thus producing a very fine and uniform spray that reduces the inflammable properties of the product.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
EXTERNAL GASKET
VPH
RTP
Orifice
COMBINATION OF HOUSING ORIFICES
GAS ORIFICE PRODUCT ORIFICE RTP Ø mm / HOUSING COLOUR
VPH Ø mm 0.40 0.50 0.60 0.70 0.80 1.00
2 x 0.30 sage red orange pink violet yellow
2 x 0.40 green white blue turquoise grey azure
2 x 0.50 black
STEM ORIFICES
N° orifices & Ø (mm)
POM HDPE NOTE
2 x 0.50 • STEM MATERIAL
Acetalic resin (POM)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium MicoflexClear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 soft on request (only for buna internal gasket)
HOUSING MATERIALAcetalic resin (POM)
DIP TUBE MATERIAL OPTIONSPolyethylene HD (HDPE) Polyipropylene on request
COSTER
1.5.04
KSL
60
50
40
30
FILLING DIAGRAMS AND FILLING SPEED GRAPH
revision: 6 30/04/2013
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
60 80 100 120 140 160 180 200
STANDARD ACTUATORS
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (diameter of the orifices on the stem and on the housing).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
7 mm 13 mm
SERIES 1300: versions without insert, with micromist insert, with directional insert, with tube holding insert and with special inserts. Can be supplied mounted on the valve. SERIES 900 - SLOTTED ACTUATOR: versions without insert, with micromist insert, and with directional insert. Can be supplied mounted on the valve.SERIES 500: with micromist insert and with directional insert.
SERIES 700: versions without insert, with micromist insert, with directional insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert.
SERIES 2100: with micromist insert.SERIES 500 SERIES 800SERIES 700
SERIES 1300
SERIES 1800
SERIES 900
SERIES 2100
COSTER
1.5.05
KV
HOUSING
STEM Ø 3,9 mm
revision: 1030/09/2015
CONTINUOUS VALVE
Recommended for products filled with compressed gas (CO2, N
2O, N
2, air).
The valve is equipped with a special housing that can increase the speed and diffusion of the propellant inside the solution, in order to reduce the initial pressure peak during the filling stage.
The use of the IFS (Impact Filling System) with these valves increases the gas solubility into the liquid phase.
The dip tube is semi-capillary, and it is inserted inside the mounting tang.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
EXTERNAL GASKET
Orifice
STEM ORIFICES
N° orifices & Ø (mm)
POM HDPE NOTE
1 x 0.27 • •
1 x 0.30 • •
1 x 0.35 • •
1 x 0.40 • •
1 x 0.50 • •
1 x 0.60 • •
1 x 0.65 •
2 x 0.50 • •
4 x 0.50 • •
STEM MATERIAL OPTIONSAcetalic resin (POM) Polyethylene HD (HDPE)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium MicoflexClear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 soft on request (only for buna internal gasket)
HOUSING MATERIALAcetalic resin (POM)
DIP TUBE MATERIAL Polyethylene HD (HDPE)
COSTER
1.5.06
KV
STANDARD ACTUATORS
revision: 10 30/09/2015
FILLING DIAGRAMS
7 mm 13 mm
10
8
6
4
2
CAN
PRES
SURE
IN B
ARS
CAN PRESSURE VARIATIONS OVER TIME DURING THE FILLING AND SATURATION STAGE
TIME (SEC) 1 10 100 200
SERIES 1300: versions without insert, with micromist insert, with directional insert, with tube holding insert and with special inserts. Can be supplied mounted on the valve. SERIES 900 - SLOTTED ACTUATOR: versions without insert, with micromist insert, and with directional insert. Can be supplied mounted on the valve.SERIES 500: with micromist insert and with directional insert.
SERIES 700: versions without insert, with micromist insert, with directional insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert.
SERIES 2100: with micromist insert.
SERIES SALUS: nasal versions for sea-water solutions.
SERIES 500 SERIES 800SERIES 700
SERIES 1300
SERIES 1800
SERIES 900
KEY Graph referring to KPM valves Graph referring to KV valves
The graph describing the pressure variations is purely indicative and is based on the following parameters:
- Aluminium can, cm3 300
- Product: cm3 200, Ethanol 99°
- Propellant: CO2, g 10
- Final pressure: 6.5 bar at 17° C
Propellant filling with IFS (Impact Filling System). Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
SERIES 2100 SERIES SALUS
COSTER
1.5.07
KVT
STEM ORIFICES
N° orifices & Ø (mm)
POM HDPE NOTE
1 x 0.27 • •
1 x 0.30 • •
1 x 0.35 • •
1 x 0.40 • •
1 x 0.50 • •
1 x 0.60 • •
1 x 0.65 •
2 x 0.50 • •
4 x 0.50 • •
HOUSING
STEM Ø 3.9 mm
revision: 6 30/04/2013
CONTINUOUS VALVE
The valve is equipped with a housing with a gas orifice (VPH): the dimensions are the same as in the KV valves.
The dip tube is semi-capillary, and it is inserted inside the mounting tang.
KVT valves are generally utilized for water-based products filled with liquid gas (LPG): in this case the orifice of the gaseous stage, together with the semi-capillary dip tube, guarantees a perfect atomisation of particles with a very fine and uniform spray.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
EXTERNAL GASKET
VPH
Orifice
GAS ORIFICEVPH Ø mm
HOUSINGCOLOUR
0.30 green0.40 pink0.50 black0.60 yellow
STEM MATERIAL OPTIONSAcetalic resin (POM) Polyethylene HD (HDPE)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium MicoflexClear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 soft on request
HOUSING MATERIALAcetalic resin (POM)
DIP TUBE MATERIAL Polyethylene HD (HDPE)
COSTER
1.5.08
KVT
STANDARD ACTUATORS
FILLING DIAGRAMS AND FILLING SPEED GRAPH
revision: 6 30/04/2013
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (number and diameter of the orifices on the stem and on the housing).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
7 mm13 mm
60
50
40
30
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
60 80 100 120 140 160 180 200
SERIES 1300: versions without insert, with micromist insert, with directional insert, with tube holding insert and with special inserts. Can be supplied mounted on the valve. SERIES 900 - SLOTTED ACTUATOR: versions without insert, with micromist insert, and with directional insert. Can be supplied mounted on the valve.SERIES 500: with micromist insert and with directional insert.
SERIES 700: versions without insert, with micromist insert, with directional insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert.
SERIES 2100: with micromist insert.SERIES 500 SERIES 800SERIES 700
SERIES 1300
SERIES 1800
SERIES 900
SERIES 2100
COSTER
1.5.09
TV
HOUSING
STEM Ø 3.9 mm
revision: 6 30/04/2013
CONTINUOUS TILT-ACTION VALVE
Recommended for products filled with compressed gas (CO2, N
2O, N
2, air).
The valve is equipped with a special housing that can increase the speed and diffusion of the propellant inside the solution, in order to reduce the initial pressure peak during the filling stage.
The use of the IFS (Impact Filling System) with these valves increases the gas solubility into the liquid phase.
The dip tube is semi-capillary, and it is inserted inside the mounting tang.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
EXTERNAL GASKET Orifice
STEM MATERIALAcetalic resin (POM)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium MicoflexClear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL Stainless steel AISI 302
HOUSING MATERIALAcetalic resin (POM)
DIP TUBE MATERIAL Polyethylene HD (HDPE)
STEM ORIFICESNUMBER & Ø (mm)
1 x 2.00
COSTER
1.5.10
TV
STANDARD ACTUATORS
FILLING DIAGRAMS
revision: 6 30/04/2013
7 mm13 mm
SERIES 600 SERIES 400VERTICAL
SERIES 600: versions without insert, with micromist insert and tube. It can be supplied mounted on the valve.SERIES 400 VERTICAL: with vertical spray; versions without insert and with micromist insert.
The graph describing the pressure variations is purely indicative and is based on the following parameters:
- Aluminium can, cm3 300
- Product: cm3 200, Ethanol 99°
- Propellant: CO2, g 10
- Final pressure: 6.5 bar at 17° C
Propellant filling with IFS (Impact Filling System). Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.CA
N PR
ESSU
RE IN
BAR
S
CAN PRESSURE VARIATIONS OVER TIME DURING THE FILLING AND SATURATION STAGE
TIME (SEC) 1 10 100 200
KEY Graph referring to KPM valves Graph referring to TV valves
10
8
6
4
2
COSTER
1.5.11
TVT
HOUSING
STEM Ø 3.9 mm
revision: 6 30/04/2013
CONTINUOUS TILT-ACTION VALVE
A housing with a gas orifice (VPH) is utilized: the dimensions are the same as in the TV valves.
The dip tube is semi-capillary, and it is inserted inside the mounting tang.
TVT valves are generally utilized for water-based products filled with liquid gas (LPG): in this case the orifice of the gaseous stage, together with the semi-capillary dip tube, guarantees a perfect atomisation of particles with a very fine and uniform spray.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
HOUSING
DIP TUBE
EXTERNAL GASKET
VPH
Orifice
GAS ORIFICE HOUSING VPH Ø mm COLOUR 0.30 green 0.40 pink 0.50 black 0.60 yellow
STEM ORIFICESNUMBER & Ø (mm)
1 x 2.00STEM MATERIAL
Acetalic resin (POM)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium MicoflexClear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL Stainless steel AISI 302
HOUSING MATERIALAcetalic resin (POM)
DIP TUBE MATERIAL Polyethylene HD (HDPE)
COSTER
1.5.12
TVT
STANDARD ACTUATORS
FILLING DIAGRAMS AND FILLING SPEED GRAPH
revision: 6 30/04/2013
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (diameter of the orifices on the stem and on the housing).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
7 mm13 mm
60
50
40
30
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
60 80 100 120 140 160 180 200
SERIES 600 SERIES 400VERTICAL
SERIES 600: versions without insert, with micromist insert and tube. It can be supplied mounted on the valve.SERIES 400 VERTICAL: with vertical spray; versions without insert and with micromist insert.
COSTER
1.5.13
KS
HOUSING
STEM Ø 3.9 mm
revision: 630/04/2013
CONTINUOUS VALVE FOR 360° USE
Thanks to the insert and ball utilized on the housing, a 360° actuation is possible.
The dip tube is inserted inside the housing tang.
KS valves can be employed both for products filled with liquid gas and for products pressurised with compressed gas.
STEM
INTERNAL GASKET
MOUNTING CUP
SPRING
INSERT
BALL
EXTERNAL GASKET
HOUSING
DIP TUBE
Orifice
STEM ORIFICES
N° orifices & Ø (mm)
POM HDPE NOTE
1 x 0.27 • •
1 x 0.30 • •
1 x 0.35 • •
1 x 0.40 • •
1 x 0.50 • •
1 x 0.60 • •
1 x 0.65 •
2 x 0.50 • •
4 x 0.50 • •
STEM MATERIAL OPTIONSAcetalic resin (POM) Polyethylene HD (HDPE)
MOUNTING CUP MATERIAL PROTECTION
Tin plate PlainExternal gold lacquered / Internal clear lacqueredClear lacqueredClear lacquered with PP laminated internal surface
(external gasket not required)Chrome-plate Internal / External PET coated
Aluminium MicoflexClear lacqueredGold lacquered
EXTERNAL GASKET MATERIAL OPTIONSBuna Chlorobutyl on request
INTERNAL GASKET MATERIALNeopreneBunaChlorobutylButyl
SPRING MATERIAL OPTIONSStainless steel AISI 302 soft on request (only for buna internal gasket)
INSERT MATERIALPolyethylene HD (HDPE)
BALL MATERIALStainless steel AISI 304
HOUSING MATERIALAcetalic resin (POM)
DIP TUBE MATERIALPolyethylene HD (HDPE)
COSTER
1.5.14
KS
STANDARD ACTUATORS
FILLING DIAGRAMS AND FILLING SPEED GRAPH
60
50
40
30
INJE
CTIO
N PR
ESSU
RE IN
BAR
S
FILLING SPEED DURING THE PRODUCTION STAGE: CM3/SEC
Maximum pressure for aluminium mounting cups
Maximum pressure for tin plate mounting cups
100 125 150 175 200 225 250 275
The filling speed graph refers to butane-propane propellant.
It is purely indicative, as it is based on historical data.
The filling speed depends on the injection pressure, on the characteristics of the filling machine and on the dimensions of the valve’s components (number and diameter of the orifices on the stem).
Given the high number of parameters that can cause significant variations in the quoted values, if specific information is required please ask Coster commercial offices to obtain precise data on a specific model.
7 mm 13 mm
SERIES 1300: versions without insert, with micromist insert, with directional insert, with tube holding insert and with special inserts. Can be supplied mounted on the valve. SERIES 900 - SLOTTED ACTUATOR: versions without insert, with micromist insert, and with directional insert. Can be supplied mounted on the valve.SERIES 500: with micromist insert and with directional insert.
SERIES 700: versions without insert, with micromist insert, with directional insert, with tube.
SERIES 800: with micromist insert.
SERIES 1800: with micromist insert.
SERIES 2100: with micromist insert.SERIES 500 SERIES 800SERIES 700
SERIES 1300
SERIES 1800
SERIES 900
revision: 6 30/04/2013
SERIES 2100