®

advanced FLOW engineering Magnum FORCE Cold Air Intake System

Instruction Manual P/N: 54-13013D / 54-13013R / 54-13013G

Make: Nissan Model: Patrol (Y61) Year: 2017-2019 Engine: I6-4.8L (Engine: TB48DE)Note: Vehicle Does Not Exist in the USA.

®

Label Qty. Description Part Number

A1 1 Pro 5R (Blue Media) 24-91128

A2 1 Pro DRY S (Gray Media) 21-91128

A3 1 Pro-GUARD 7 (Gold Media) 72-91128

B 1 Tube 05-13013B1

C 1 Housing 05-13012B2

D 1 Fitting 03-50150

E 1 Coupling, Silicone Bellow 05-01404

F 1 Seal, Trim: 3/4" Bulb (24") 05-00007

G 1 Seal, Trim: 3/4" Bulb (16") 05-00007

H 1 Coupling, Elbow 05-00968

I 2 Clamp, #048 03-50007

J 2 Clamp, #064 03-50006

K 1 Adaptor 05-00611

L 5 Screw, Btn Hd Socket: M6 03-50113

M 3 Isolation Mount: M6 03-50022

N 3 Nut, Hex Nyloc: M6 03-50185

O 3 Washer, Flat: M6 03-50070

P 2 Screw, Torx: M4 03-50490

Q 1 Pre-Filter 28-10243Installation will require the following tools:10mm & 8mm nut drivers, pliers, T20 & T25 drivers, 10mm & 11mm deep sockets & drivers and 10mm wrench.

Note: Not legal for use in California. The use of this device in any on-road or off-road vehicles registered with the Califor-nia Dept of Motor Vehicles (DMV) is strictly prohibited. Vehicle does NOT exist in the US.

• Please read the entire instruction manual before proceeding.• Ensure all components listed are present.• If you are missing any of the components, call technical support at 951-493-7100 or e-mail tech@afepower.com.• Ensure you have all necessary tools before proceeding.• Do not attempt to work on your vehicle when the engine is hot.• Disconnect both the negative battery terminal before proceeding.

Page 2

Retain factory parts for future use.

aFepower.comPage 3

A1/A2/A3

C

B

D

L

E

J

K

G

F

H

I

I

J

MM

MN

NON

OO

PQ

®

Refer to Figure A for Step 1Step 1: Use a 10mm nut driver to remove the rear nut 1 and three screws 2 holding the engine cover.

Remove the engine cover and set aside.

REMOVAL

Page 4

Figure A

1

2

2

2

Refer to Figure B for Step 2Step 2: Remove the vacuum hose 3 from the retainer on the u-shape air duct. Push back on the lock springs 4 and remove the u-shape air duct from the air intake assembly.

aFepower.comPage 5

Figure B

REMOVAL

3

4

4

®

Refer to Figure C for Step 3NOTE: MAF sensor may look different depending on model years. Step 3: Disconnect the mass air flow sensor and disengage the wire loom from the air intake tube.

Figure C

Page 6

REMOVAL

Refer to Figure D for Step 4NOTE: MAF sensor may look different depending on model years.Step 4: Use an 8mm nut driver to loosen the clamp at the mass air flow sensor tube. Remove the two wing nuts and two washers holding down the air cleaner assembly and remove the assembly.

Figure D

aFepower.comPage 7

REMOVAL

®

Page 8

Refer to Figure E for Step 5Step 5: Use a 10mm nut driver to remove the screw holding the air intake tube assembly resonator to the firewall. Use an 8mm nut driver to loosen the clamp at the throttle body. Using pliers, remove the vent hose to the air intake tube. Remove the small vacuum hose from the air intake tube assembly resonator. Remove the complete air intake tube assembly.

Figure E

REMOVAL

Step 6: Using a 10mm socket and driver, remove the two mounting brackets from the engine bay.

Refer to Figure F for Step 6

Page 9

Figure F

REMOVAL

aFepower.com

Refer to Figure G for Step 7Step 7: Install the 3 isolation mounts as shown.

Page 10

Figure G

REMOVAL

®

aFepower.comPage 11

Refer to Figure H for Steps 8-9Step 8: Install the filter adapter onto the housing with the 5 hex screws.Step 9: Install the trim seal onto the housing as shown.

Figure H

INSTALL

®

Page 12

Refer to Figure I for Step 10Step 10: Install the housing onto the 3 isolation mounts and secure with the 3 washers and 3 nylock nuts.

Figure I

INSTALL

aFepower.comPage 13

Refer to Figure J for Step 11Step 11: Reinstall the u shaped air duct using the lock springs as shown.

Figure J

INSTALL

®

Page 14

Refer to Figure K for Step 12Step 12: Using a T-20 driver, remove the mass air flow sensor from the air cleaner assembly and install it on the aFe intake tube with the two supplied screws using a T-25 driver. Do not overtighten.

Figure K

INSTALL

aFepower.comPage 15

Refer to Figure L for Step 13Step 13: Using pliers, remove the clamp holding the elbow vent fitting from the air intake tube and install it into the supplied silicone coupler.

Figure L

INSTALL

®

Page 16

Refer to Figure M for Steps 14-16Step 14: Install the silicone coupler onto the throttle body with the supplied clamp as shown. Do not

tighten the clamp at this time.

Step: 15: Install the vent hose onto the elbow vent fitting with the spring clamp.

Step 16: Install the supplied vacuum hose connector into the vacuum hose removed from the resonator

earlier. Install the vacuum hose connector to the silicone coupler.

Figure M

INSTALL

aFepower.comPage 17

Refer to Figure N for Step 17Step 17: Install the aFe intake tube to the throttle body and the filter adapter using the provided silicone

coupler using the hose clamps as shown. Tighten all hose clamps.

Figure N

INSTALL

®

Page 18

Refer to Figure O for Step 18Step 18: Re-connect the mass air flow sensor.

Figure O

INSTALL

Page 19

Refer to Figure P for Step 19Step 19: Reinstall the engine cover. Check all the components are tight and secure. Your installation is

now complete.

Note: Check all bolts, clamps and connectors after 100-200 miles.

Figure P

aFepower.com

INSTALL

Page 20

®

Page left blank intentionally

Page 21

Page left blank intentionally

aFepower.com

To purchase any of the items above, view airflow charts, dyno graphs, photos, and video; please go to aFepower.com.

Page 22

Pro DRY S Air Filter

P/N: 21-91128 P/N: 28-10243

P/N: 90-50501

Pre-Filter

Blue Squeeze Restore Kit

Pro 5R Air Filter

P/N: 24-91128

®

Pro-GUARD 7 Air Filter

P/N: 72-91128

P/N: 90-59999

Pro DRY S Restore Kit

P/N: 90-50500

Gold Squeeze Restore Kit

P/N: 46-36005 (w/ Auto Trans.) 46-36006 (w/ Manual Trans.)

Throttle Body Spacer

P/N: 48-36105-YC (Street) 48-36105-YN (Race)

Twisted Steel Headers

P/N: 49-36115-P (Pol. Tip) 49-36115-B (Blk. Tip)

Cat-Back Exhaust System

P/N: 201-5600-05 (Front) 202-0056-01 (Rear)

Front/Rear Shocks

P/N: 201-9900-01 (Front) 202-0099-01 (Rear)

Front/Rear Springs

WarrantyGeneral Terms:• aFe warrants their products to be free from manufacturer’s defects due to workmanship and material.

• This warranty applies only to the original purchaser of the product and is non-transferrable.

• Proof of purchase of the aFe product is required for all warranty claims.

• Warranty is valid provided aFe instructions for installation and/or cleaning were properly followed.

• Proper maintenance with regular inspections of product is required to insure warranty coverage.

• Damage due to improper installation, abuse, unauthorized repair or alteration is not warranted.

• Incidental or consequential damages or cost, including installation and removal of part, incurred due to failure of aFe product is not covered under this warranty.

• All warranty is limited to the repair and/or replacement of the aFe part. To request Return Goods Authorization (“RGA”), email RGA@afepower.com or call (951)493-7100. Upon receipt of the RGA, you must return the product to the address provided in the RGA, freight prepaid and accompanied with a dated proof of purchase and the RGA. Upon receipt of the defective product and upon verification of proof of purchase, aFe will either repair or replace the defective product within a reasonable time, not to exceed thirty days.

Product Category P/N Prefix Warranty duration Direct OE Replacement Filters 10, 11, 30, 31, 71, 73 Life of the vehicleRacing Filters 18 1 year Universal 21, 24, 72 2 yearsAir Intake Systems 50, 51, 54, 55, 75 2 yearsExhaust Systems 49 2 yearsIntercoolers & Intercooler Tubes 46-2 2 yearsIntake Manifolds 46-1 2 yearsDifferential Cover 46-7 Life of the vehicleExhaust Manifolds 46 2 yearsThrottle Body Spacers 46-3 2 yearsFluid Filters 44 90 daysPre-Filters 28 2 yearsHeavy Duty OE Replacement 70 2 yearsPowerSports OE Replacement 81, 87 2 yearsPowerSports Intake Systems 85 2 years

No other warranty expressed or implied applies nor is any person or advanced FLOW engineering authorized to assume any other warranty. Some States do not allow the exclusion or limitation of incidental or consequential damages or do not allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

aFepower.comPage 23

advanced FLOW engineering, inc.252 Granite Street Corona, CA 92879

TEL: 951.493.7100 • TECH: 951.493.7134E-Mail:Tech@aFepower.com P/N: 06-81120

®