ADDENDUM to CONTRACT DOCUMENTS - Delaware

ADDENDUM to CONTRACT DOCUMENTS Date: January 15, 2021 To: All Bidders

From: Maureen Q. Rozanski, BSA+A Copies: All Bidders Keith Hopkins, Appoquinimink School District Chris McCone, EDiS Company Bob Grove, RG Architects

Project Name: FURNITURE, FIXTURES AND EQUIPMENT – SILVER LAKE ELEMENTARY SCHOOL

Project Number: 18.019

Subject: ADDENDUM 3

NOTICE: Attention is called to the following item(s), effective as of the date above, which shall be added to, deleted from, or changed in the contract documents dated December 16, 2020 and any previously issued addenda, thereby incorporating these items into the contract documents. Attach this Addendum to the project manual for this project. Work or materials not specifically mentioned herein are to be as described in the main body of the specifications and as shown on the drawings. Bidders shall acknowledge receipt of this Addendum in the space provided on the Bid Form. Failure to do so may subject the bidder to disqualification. The following clarification, changes and/or additions shall by this reference be incorporated into the contract documents as though fully set forth therein.

ADDENDUM 3 PAGE 2

A. GENERAL

Item No.

Item

A-1 Bidders to acknowledge all Addendums on Bid Form 1634-004113

B. BIDDER QUESTIONS & CLARIFICATIONS

Item No.

Question/Answer:

B-1 Please see attachments for the Question and Answer Log.

C. MODIFICATIONS TO DRAWINGS

Item No.

Description:

C-1 N/A

D. MODIFICATIONS TO SPECIFICATIONS

Item No.

Description:

D-1 Add Specification Item LS-6A End Panel

D-2 Revise Specification Item LS-4 Book Display Shelving

D-3 Bid Summary Docs. – Add Item LS-6A to Group H

D-4 Revise Specification Sheet CH-08 to read Qty. 8 (As noted on bid summary)

E. ATTACHMENTS

Items Date

Question and Answer Log 01.15.21

Specification sheet - Item LS-6A 01.15.21

Specification sheet – Item LS-4 01.15.21

Specification Sheet – Item CH-08 01.15.21

Section 004113 Bid Summary – Add Item LS-6A to Group H 01.15.21

Bid Summary – Add Item LS-6A to Group H 01.15.21

-

END OF ADDENDUM 3

OWNER: APPOQUINIMINK SCHOOL DISTRICT

PROJECT NUMBER: 18.019PROJECT NAME:

Question # Question Vendor Section/Item #Received

DateAnswer Date Response

1Detailed descriptions and images of Lakeshore items can be found on the attached Substitution Request. See attached.

Lakeshore Learning T-01 & P-1 01.08.21 01.11.21Please see attached PDF for response.

2 type of caster is NOT specified. Hard caster for carpet? Or, soft caster for hard floor?

EFS CH-01 01.11.21 01.12.21Hard caster for Carpet

3 glide – should a standard multi-surface glide be used? EFS CH-05 01.11.21 01.12.21 Standard multi-purpose glides4 description specifies arms but the picture is armless. Please

confirm. Also, standard multi-surface glide?EFS CH-06 01.11.21 01.12.21

CH-06 - No arms with standard multi-purpose glides

5description specifies arms but the picture is armless. Please confirm. What type of caster? Carpet or hard floor?

EFS CH-07 01.11.21 01.12.21CH07 - No arms. Twin wheel type casters for multiple floor surfaces.

6 Please clarify whether the price for furniture installation should be separate from the furniture or included with the cost.

Turning Point 01.12.21 01.12.21 The price for furniture installationto be included in the unit cost of the item.

1 Do we need to submit brochures, warranties, and/or cleaning care with the bid or only for substitutions?

Douron N/A 01.15.21 01.15.21Brochures, warranties and care are only required for substitutions.

2 SOI - CH-10 per the manufacturer this should be a weight capacity of 400lbs per seat. Your spec shows 800lbs, is 400lbs acceptable?

Douron CH-10 01.15.21 01.15.21 400 lb is acceptable.

3 Media Tech – CH-08 – The quantity is listed as 4 on the spec but drawing has 8, can you confirm the quantity?

Douron CH-08 01.15.21 01.15.21 Quatity to be (8) - Please see Addendum #3.

4 Item #LS-7 and LS-8: Inlay 2 stain color is specified as Charcoal. TMC does not have a charcoal standard stain. Is this to be a custom stain?

Douron LS-7 & LS-8 01.15.21 01.15.21 Allow for custom Stain.

5 There are (12) LS-3 72”W Double Faced Mobile units and (1) LS-4 108”W Double faced Mobile Unit, but only (14) Double Faced End Panels. Please confirm quantity and specifications for end panels.

Douron LS-3 01.15.21 01.15.21Double faced panels to be included. See specification added to Addendum #3.

6 Item #’s LS-3 and LS-4: Will you accept open mobile bases? Douron

LS-3 & LS-401.15.21

01.15.21 All bases to be closed.

7Substitution request. Please see attached . Douron

US-1, US-2 & US-3

01.15.21 01.15.21Substituions Approved.Note: All shelving to be free standing.

8 Substitution request. Please see attached . WB Mason 01.15.21 01.15.21 Please see attached PDF for response. 9 Please accept Global and/or Sit on It seating as alternates for

all Hon seating. Corporate Interiors N/A 01.15.21 01.15.21

Substitutions can not be approved – Product specifications, brochures and fabrics need to be provided for review.

10 Please provide the bid form in an Excel format for final submission.

Corporate Interiors N/A 01.15.21 01.15.21 Bid Form available as per bid package format.

11Please accept Tennsco for all metal and library shelving. Corporate Interiors N/A 01.15.21 01.15.21

Substitutions can not be approved – Product specifications, brochures and fabrics need to be provided for review.

QUESTION LOG

BSA+A

Silver Lake Elementary School – FFE

ADDENDUM #2

ADDENDUM #3

Douron’s Substitution Request:

SILVER LAKE ELEMENTARY SCHOOL FF&E

For US-1, US-2 and US-3: We would like to substitute Penco Cipper Shelving.

• US-1: Penco Clipper Shelving

MODEL NO.: 1H203618C+ Offset Angle Post + side and back sway brace

DIMENSIONS: 36”W x 18”D x 87”H

DESCRIPTION: Penco Open Clipper Unit. Unit shall have 6 shelves with a weight

capacity of 850 lbs. per shelf. Each unit shall include (1) Basic Open unit consisting

of 1 front box post, 2 rear offset angle posts, side and back sway braces, and (1)

End Kit consisting of a front box post and 1 pair of side sway braces. Front and rear

flanges of each shelf shall utilize Box Beam construction for extra strength. Sides are

double flanged. Flanges are welded to the underside of shelf on 3”centers. Four

Clipper Compression Clips shall be included with each shelf. Clip allows shelf

adjustment on 1” vertical centers.


MODEL NO.: 1H203615C + Offset Angle Post + side and back sway brace











MODEL NO.: 1H203612C + Offset Angle Post + side and back sway brace


APPROVED - ALL SUBSTITUTIONSNOTE: ALL SHELVING TO BE FREE STANDING









Renderings are created for conceptual purposes only. Actual colors and textures of final products may vary from those shown.

Appoquinimink School DistrictSilver Lake Elementary School

Substitution Request

Item: CH-10

TOTAL QUANTITY: 32

Furniture Specification

Manufacturer: SitOnItModel Number: NNO.FS14.Description: Lounge Chair, Nano DiamondFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using high strength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Field replaceableparts. 800 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.

COMMENTS: Fixed Glides – Dual upholstery

SEAT FABRIC: DesignTex Leap 3600-901 Color: PebbleBASE FABRIC: SitOnIt Optima Obsidian

Manufacturer: FomcoreModel Number: F000396-GDescription: Custom Diamond Ottoman with Dual Upholstery, 18”H

1. FOAM #70, 37.5 x 25 x 16.5 2. WOOD 1/2" MDF, 36.15 x 24.10 3. 1" SLIDER GLIDE W/ SPACER&WASHER

Options:

SEAT FABRIC: Designtex Leap color PebbleBASE FABRIC: TBD

*Potential Alt Seat Upholstery: Chambray, Gray (Vinyl)

llucas

Typewritten Text

NOT APPROVED: Base fabric to be as specified

Item: CH-10

TOTAL QUANTITY: 32


Manufacturer: SitOnItModel Number: NNO.FS14.Description: Lounge Chair, Nano DiamondFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using high strength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Field replaceableparts. 800 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.

COMMENTS: Fixed Glides – Dual upholstery

SEAT FABRIC: DesignTex Leap 3600-901 Color: PebbleBASE FABRIC: SitOnIt Optima Obsidian

Manufacturer: Media TechnologiesModel Number: MiscDescription: Fulltime Custom Ottoman, 37-1/2"W x 25"D x 17"H, w/ 2"T High Density Foam on 1"T Assembled Frame

Options:


*Potential Alternate Base Upholstery, Momentum; Groove, Harbor

*Product is designed to meet the Sit On It product specifications. Please refer to the Full Time brochure for images of product line.

llucas

Typewritten Text


Item: CH-11

TOTAL QUANTITY: 8


Manufacturer: SitOnItModel Number: NNO.FS15.Description: Lounge Chair, Nano TrapezoidFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using high strength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Field replaceableparts. 400 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.COMMENTS: Fixed Glides – Dual upholstery

SEAT FABRIC: Designtex Leap color PebbleBASE FABRIC: Sitonit Optima Obsidian

Manufacturer: FomcoreModel Number: F000397-GDescription: Custom Trapezoid Ottoman with Dual Upholstery, 18”H

1. FOAM #70, 52 x 25 x 16.52. WOOD 1/2" MDF, 50.70 x 24.253. 1" SLIDER GLIDE W/ SPACER&WASHER

Options:



llucas

Typewritten Text

Not Approved: Base Fabric to be as Specified

Item: CH-11

TOTAL QUANTITY: 8


Manufacturer: SitOnItModel Number: NNO.FS15.Description: Lounge Chair, Nano TrapezoidFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using high strength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Field replaceableparts. 400 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.COMMENTS: Fixed Glides – Dual upholstery


Manufacturer: Media TechnologiesModel Number: MiscDescription: Fulltime Custom Ottoman, 52"W x 25"D x 17"H, w/ 2"T High Density Foam on 1"T Assembled Frame

Options:




llucas

Typewritten Text


llucas

Typewritten Text

Sample

llucas

Typewritten Text

not submitted for review

Item: CH-12

TOTAL QUANTITY: 1


Manufacturer: SitOnItModel Number: NNO.FS16.Description: Lounge Chair, Nano BoomerangFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using high strength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Field replaceableparts. 400 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.COMMENTS: Fixed Glides – Dual upholstery


Manufacturer: FomcoreModel Number: F000397-G (x2)Description: Custom Trapezoid Ottoman (x2 to Create Boomerang Shape) with Dual Upholstery, 18”H

1. FOAM #70, 52 x 25 x 16.52. WOOD 1/2" MDF, 50.70 x 24.253. 1" SLIDER GLIDE W/ SPACER&WASHER

Options:



llucas

Typewritten Text


llucas

Typewritten Text

llucas

Typewritten Text

sample not submitted for review

Item: CH-12

TOTAL QUANTITY: 1


Manufacturer: SitOnItModel Number: NNO.FS16.Description: Lounge Chair, Nano BoomerangFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using high strength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Field replaceableparts. 400 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.COMMENTS: Fixed Glides – Dual upholstery



Options:




llucas

Typewritten Text


llucas

Typewritten Text

Sample not submitted for review

Item: CH-13

TOTAL QUANTITY: 23


Manufacturer: SitOnItModel Number: NNO.FS13.TM3Description: Lounge Chair, Nano TriangleFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using highstrength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Fieldreplaceableparts. 400 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.

SEAT LAMINATE: LinenBASE FABRIC: Sitonit Optima Obsidian

Manufacturer: FomcoreModel Number: F000398-G, TFL000398Description: Custom Triangle Ottoman with TFL Top, 18”H

1. FOAM #100, 23 x 21 x 15.752. WOOD 1/2" MDF, 21.73 x 19.843. 1" SLIDER GLIDE W/ SPACER&WASHER4. TFL TOP FOR F000398, 22.16 x 20.23

Options:

SEAT LAMINATE: LinenBASE FABRIC: TBD

*Potential Alt Base Upholstery: Chambray, Gray (Vinyl)

llucas

Typewritten Text

Not Approved: Fabric to be as specified

llucas

Typewritten Text


Item: CH-13

TOTAL QUANTITY: 23


Manufacturer: SitOnItModel Number: NNO.FS13.TM3Description: Lounge Chair, Nano TriangleFrame is comprised of a rugged hardwood plywood construction. SITONIT creates the frame using highstrength glue and interlocking wood joints for durable performance. Extra strength monofilament webbing suspensionplatform features high-resilient and high-density foam to create comfort and rebound in a low-profile cushion. Fieldreplaceableparts. 400 lbs. per seat weight capacity. 12-Year Warranty. BIFMA Level 1 Certified.

SEAT LAMINATE: LinenBASE FABRIC: Sitonit Optima Obsidian


Options:

Seat Laminate: TBDBASE FABRIC: TBD



llucas

Typewritten Text


llucas

Typewritten Text


Item: CH-14

TOTAL QUANTITY: 11


Manufacturer: SitOnItModel Number: PAS.FS1.OS1Description: Pasea Mini ottoman. Dual Fabric/multiple upholstery. Slate Base with Fixed glides. 400 lb. per seat weight capacity. 12 year warranty.

SEAT FABRIC: SitOnIt Optima ObsidianBASE FABRIC: Sitonit Optima Obsidian

Manufacturer: FomcoreModel Number: F000398-G, TFL000398Description: Round Ottoman, 17.5”H

1. FOAM 70#, 24 DIA x 162. WOOD -1/2 MDF, 23.253. 1" SLIDER GLIDE W/ SPACER&WASHER

Options:

FABRIC: TBD

*Potential Alt Base Upholstery: Chambray, Gray (Vinyl)

llucas

Typewritten Text


llucas

Typewritten Text

Sample not submitted for Review

Item: CH-14

TOTAL QUANTITY: 11


Manufacturer: SitOnItModel Number: PAS.FS1.OS1Description: Pasea Mini ottoman. Dual Fabric/multiple upholstery. Slate Base with Fixed glides. 400 lb. per seat weight capacity. 12 year warranty.

SEAT FABRIC: SitOnIt Optima ObsidianBASE FABRIC: Sitonit Optima Obsidian

Manufacturer: Media TechnologiesModel Number: MiscDescription: Fulltime Custom Round Ottoman, 24"W x 24"D x 17-1/2"H, w/ 2"T High Density Foam on 1"T Assembled Frame

Options:

Fabric: TBD


llucas

Typewritten Text


Item: ML-01

TOTAL QUANTITY: 38


Manufacturer: Smith SystemsModel Number: 265536Description: Sit to Stand Lectern, 21” x 30” x 30”-45” Oblong Top, The The semi-transparent privacy screen can be flipped up or down, with screws, to the teacher’s preference of modesty panel (for sitting) or desktop privacy screen. The lectern features a 10”x 14”x 3″ depthbasket for laptop or tablet storage. The 3/4” thick worksurface consists of a 45 lb density particle board core with a 0.030” high pressure laminated surface and a 0.020” melamine backer sheet. The edge of the tabletop features 4mm t-mold, which is then fastened to the underside of the work surface every 6 to 8 inches to assure a long lasting fit. The Sit + Stand lectern unit has an adjustable column, that is gas assisted to lift from 30” to 45” in height. Adjustability is controlled with the hand operated unit mounted on the right side of the desk. The unit rolls smoothly on 3” dual-wheel casters, which eachhave a locking mechanism.

Laminate: Pewter MeshEdge: PlatinumFrame: Charcoal Gray

Manufacturer: HaskellProduct Series: FuzionModel Number: FZPN7.2226/FZPNBKSH/FZPNMODDescription: Sit to Stand Lectern with Y Base, 22”D x 30”W x 28-1/4”-42”H, Locking Casters, Bookshelf/Laptop Storage and Modesty Panel

Base: PlatinumLaminate: Wilsonart; Pewter Mesh

Options:

Edge: TBD Modesty Specified But Not Pictured

llucas

Typewritten Text

Not Approved:

llucas

Typewritten Text

Does not meet height range of specified product

Item: T-02

TOTAL QUANTITY: 4


Manufacturer: SitOnItModel Number: MZM.TT6.TZ21.TE2.TH16Description: 21” Dia. X 16” H. SitonitMezzanine Table with Clear Maple top and Brushed Aluminum Legs.

TOP FINISH: FCW1 Clear MapleLEGS: LSL1 Brushed AluminumEDGE: TE2 Bevel Edge

Manufacturer: Media TechnologiesProduct Series: TimetableModel Number: TT0024-16Description: Occassional Table, 24"Dia x 16"H1-1/4"T PB construction w/ HPL surface & 3mm PVCedge, (4) welded powder coated steel legs w/ levelingGuides

Options:

Powdercoat Legs: 19 OptionsLaminate: 92 Laminate OptionsEdge: 35 PVC Edge Options

llucas

Typewritten Text

Not Approved: Table to be 21" Dia

Item: T-03

TOTAL QUANTITY: 4


Manufacturer: Smith SystemsModel Number: 25242fDescription: 48” X60”X29” Tables with 1 1/4” thick WORK SURFACE consists of a 45 lbdensity particle board core with a .030” high pressure laminated surface and a .020” melamine backer sheet. Edge 3mm flat self edge. Frame consists of two fully welded leg segments and a center support channel. The legs are attached to the pre-drilled holes in the top with #10 x 5/8” wood screws through a 14-gauge steel mounting plate. Mounting plate is welded to (2) 60mm x 60mm 14-gauge steelsquare tube legs which are welded to a 1” x 2” 14-gauge steel tube cross bar. The center support channel is 2” x 3” 14-gauge steel, with 14-gauge steel end plates for maximum tability. The center support channel is onnected to the legs by (4) connector bolts. 4” casters are standard. 1-3/4" Maple table. Diversified Woodcrafts Inc. is SEFA compliant and MAS Certified Green. Dual under table supports. Full steel tube legs with additional cross member. Heavy duty 11 gauge steel.Locking swivel casters. Powdercoat finishWORK TOP: Mission Maple MIMBASE: Platinum PL

Manufacturer: ColumbiaModel Number: CustomDescription: 48 X 60 x 29, Fixed Height A-Frame Maker Space Tables, 29” Fixed Height with HPL Particle Board Top with 3mm Self-Edge with Casters

Base: PlatinumLaminate: Wilsonart; Mission Maple

Pictured with Butcher Block TopSpecified with HPL Top

llucas

Typewritten Text

Not Approved: Specification information not complete for product comparison.

llucas

Line

Item: LS-1

TOTAL QUANTITY: 19


Manufacturer: MontelModel Number: Aetnastak ShelvingDescription: 78 h. x 36 w. X 13 d. -6 Tiers Single faced steel cantilever shelving to have overall depth dimension of 13". Actual shelf depth is 11”. Base shelf to be a Universal Sloping Shelf. Five individually adjustable shelves to have integral back edge formed of not less than 18-gauge steel. The rear of the shelf shall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. A kick strip shall be provided as specified under closed base shelf. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Shelving units must be capable of being leveled after book weight is applied. Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45 lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Wall Anchoring required.

Manufacturer: BorroughsProduct Series: WilsonstakModel Number: 31090-001-000, 31100-030-XXX, 31231-040-XXX, M6121B-XXX, MIBS612-XXX, MWCB8-XXX, Description:• (228)Sliding Divider 9”, Chrome Plated• (114)Adjustable Backstops 36”• (19)Upright Frame 36 x 78• (95)Adjustable Integ Back Shelf 36 x 12• (19)Integ. Back Base Shelf 36 x 12• (19)Canopy Brackets

Options:

Standard Borroughs Finish

*Please see Wilsonstak Brochure and Specification sheets for additional information and photos.

llucas

Typewritten Text

Not Approved: Shelving compatibility with project specified end panels (LS-5-8) to be confirmed and documented - information not provided. Specification not complete for comparison ie: Canopy top thickness/construction not noted. Frame spreader construction does not match project specification.

llucas

Typewritten Text

llucas

Typewritten Text

LS-1-8 to be bid as a group

Item: LS-1

TOTAL QUANTITY: 19


Manufacturer: MontelModel Number: Aetnastak ShelvingDescription: 78 h. x 36 w. X 13 d. -6 Tiers Single faced steel cantilever shelving to have overall depth dimension of 13". Actual shelf depth is 11”. Base shelf to be a Universal Sloping Shelf. Five individually adjustable shelves to have integral back edge formed of not less than 18-gauge steel. The rear of the shelf shall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. A kick strip shall be provided as specified under closed base shelf. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Shelving units must be capable of being leveled after book weight is applied. Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45 lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Wall Anchoring required.

Manufacturer: Media TechnologiesProduct Series: 31 SeriesModel Number: 31-8412M, 31-BS10Description: Shelving, Single Faced Starter • 37"W x 12-1/2"D x 84"H• Steel Frame, Maple Top, Sides, Toe, 1 Base and 5Adjustable Steel Shelves• Sliding Metal Book Support for Standard Steel

Shelves, 8-1/4"L x 6"H

Options:

Finish: MapleStandard Powdercoat Finish

*Please see 31 Series brochure for additional information and photos.

llucas

Typewritten Text

Not Approved: LS-1-8 to be bid as a group Shelving compatibility with project specified end panels (LS-5-8) to be confirmed and documented - information not provided. Specification not complete for comparison ie: Canopy top thickness/construction not noted. Frame spreader construction does not match project specification.

Item: LS-2

TOTAL QUANTITY: 8


Manufacturer: MontelModel Number: Aetnastak Cantilever Library ShelvingDescription: Single faced steel cantilever shelving to have overall depth dimension of 13". Actual shelf depth is 11”. Base shelf to be a Universal Sloping Shelf. One individually adjustable shelf to have integral back edge formed of not less than 18-gauge steel. The rear of the shelf shall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. A kick strip shall be provided as specified under closed base shelf. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Shelving units must be capable of being leveled after book weight is applied.Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45 lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Wall Anchoring required.

Manufacturer: BorroughsProduct Series: WilsonstakModel Number: 31090-001-000, 31100-030-XXX, EWR, M6121B-XXX, MBS612SLP-XXX, MWCB8-XXXDescription:• (16)Sliding Divider 9”, Chrome Plated• (8)Adjustable Backstops 36”• (8)Special Size Frame 36 x 36 @ 34”• (8)Adjustable Integ Back Shelf 36 x 12• (8)Sloped Base SF 36 X 12• (8)Canopy Brackets

Options:



llucas

Typewritten Text


Item: LS-2

TOTAL QUANTITY: 8


Manufacturer: MontelModel Number: Aetnastak Cantilever Library ShelvingDescription: Single faced steel cantilever shelving to have overall depth dimension of 13". Actual shelf depth is 11”. Base shelf to be a Universal Sloping Shelf. One individually adjustable shelf to have integral back edge formed of not less than 18-gauge steel. The rear of the shelf shall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. A kick strip shall be provided as specified under closed base shelf. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Shelving units must be capable of being leveled after book weight is applied.Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45 lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Wall Anchoring required.

Manufacturer: Media TechnologiesProduct Series: 31 SeriesModel Number: 31-8412M, 31-BS10Description: Shelving Single Faced Starter • 37"W x 12-1/2"D x 36"H• Steel Frame, Maple Top, Sides, Toe, 1 Base and 1Adjustable Steel Shelves• Sliding Metal Book Support for Standard Steel


Options:



llucas

Typewritten Text


Item: LS-3

TOTAL QUANTITY: 12


Manufacturer: MontelModel Number: Aetnastak Cantilever Library ShelvingDescription: Double faced steel cantilever shelving to have overall depth dimension of 24". Actual shelf depth is 11”. Three individuallyadjustable shelves to have integral back edge formed of not less than 18-gauge steel. The rear of the shelf shall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to beshaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at thecolumn. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Mobile Base: Closed Base for Cantilever Shelving. The frame is recessed into the base for greater stability and rigidity.Each half-base shall be made of 12-gauge steel and shall be designed to hide the wheels. The 2-Piece Closed Base on wheels shall have four (4) 5” swivel wheels and shall be 6 1/4" high overall. Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners

Manufacturer: BorroughsProduct Series: WilsonstakModel Number: 31090-001-000, 31100-030-XXX, M6121B-XXX, MCST4825A-XXX, MCST4825S-XXX, MWCB8-XXXDescription:• (288)Sliding Divider 9”, Chrome Plated• (144)Adjustable Backstops 36”• (144)Adjustable Integ Back Shelf 36 x 12• (12 EA)Starter and Adders – Caster Base 36 X 48• (48)Canopy Brackets

Options:



llucas

Typewritten Text


Item: LS-3

TOTAL QUANTITY: 12


Manufacturer: MontelModel Number: Aetnastak Cantilever Library ShelvingDescription: Double faced steel cantilever shelving to have overall depth dimension of 24". Actual shelf depth is 11”. Three individuallyadjustable shelves to have integral back edge formed of not less than 18-gauge steel. The rear of the shelf shall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to beshaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at thecolumn. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Mobile Base: Closed Base for Cantilever Shelving. The frame is recessed into the base for greater stability and rigidity.Each half-base shall be made of 12-gauge steel and shall be designed to hide the wheels. The 2-Piece Closed Base on wheels shall have four (4) 5” swivel wheels and shall be 6 1/4" high overall. Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners

Manufacturer: Media TechnologiesProduct Series: 31 SeriesModel Number: 31-3612M, 31-BS10Description:• (1) Shelving Double Faced Starter Mobile, 37"W x24"D x 48"H• (1) Shelving Double Faced Adder Mobile 36"W x24"D x 48"H• Steel Frame, Maple Top, Sides, Toe, 2 Base and 4Adjustable Steel Shelves, Casters (4)• Sliding Metal Book Support for Standard Steel


Options:



llucas

Typewritten Text


Item: LS-4

TOTAL QUANTITY: 1


Manufacturer: MontelModel Number: Aetnastak Cantilever Mobile ShelvingDescription: Double faced steel cantilever shelving to have overall depth dimension of 24". Base shelf to be a Universal Sloping Shelf. Two individually adjustable shelves to have integral back edge formed of not less than 18-gauge steel. The rear of the shelfshall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Mobile Base: Closed Base for Cantilever Shelving. The frame is recessed into the base for greater stability and rigidity. Each half-base shall be made of 12-gauge steel and shall be designed to hide the wheels. The 2-Piece Closed Base on Wheels shall have four (4) 5” swivel wheels and shall be 6 1/4" high overall.Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Successful bidder must submit shop drawings to architect prior to order placement.

Manufacturer: BorroughsProduct Series: WilsonstakModel Number: 31090-001-000, 31100-030-XXX, 31231-040-XXX, M6121B-XXX, MBS624SLP-XXX, MWCB8-XXXDescription:• (24)Sliding Divider 9”, Chrome Plated• (15)Adjustable Backstops 36”• (3)Upright Frame 36 X 48• (12)Adjustable Integ Back Shelf 36 x 12• (3)Sloped Base DF 36 X 24• (6)Canopy Brackets

Options:



llucas

Typewritten Text


Item: LS-4

TOTAL QUANTITY: 1


Manufacturer: MontelModel Number: Aetnastak Cantilever Mobile ShelvingDescription: Double faced steel cantilever shelving to have overall depth dimension of 24". Base shelf to be a Universal Sloping Shelf. Two individually adjustable shelves to have integral back edge formed of not less than 18-gauge steel. The rear of the shelfshall be formed with a vertical flange and 1-1/2" high, and a 1/4" return to the rear and 1/4" down. The integral back shall be designed to receive a sliding wire book support. Provide two sliding back edge book supports per shelf. Each shelf shall have an adjustable backstop. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Mobile Base: Closed Base for Cantilever Shelving. The frame is recessed into the base for greater stability and rigidity. Each half-base shall be made of 12-gauge steel and shall be designed to hide the wheels. The 2-Piece Closed Base on Wheels shall have four (4) 5” swivel wheels and shall be 6 1/4" high overall.Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Successful bidder must submit shop drawings to architect prior to order placement.

Manufacturer: Media TechnologiesProduct Series: 31 SeriesModel Number: 31-3612M, 31-BS10Description:• (2) Shelving Double Faced Starter Mobile, 37"W x24"D x 48"H• (1) Shelving Double Faced Adder Mobile 36"W x24"D x 48"H• Steel Frame, Maple Top, Sides, Toe, 2 Base and 4Adjustable Steel Shelves, Casters (4)• Sliding Metal Book Support for Standard Steel


Options:



llucas

Typewritten Text


Item: LC-1

TOTAL QUANTITY: 2


Manufacturer: Smith SystemModel Number: 21092Description: 36” x 14” x 43” Book Truck, Truck constructed of 20-gauge steel full height end panels welded to 1” square 18-gauge steel tubing frame with formed in handles that radius. Sloping shelves are constructed of 20-gauge steel, are single-sided, and are 34”L x10.4”D x 4.6”H back. Sloping shelves are welded to the frames and end panels of the book truck. Clearance betweenshelves is 13.1”. Casters shall be 4” diameter dual wheel with soft tread for quiet operation. Dual wheels have no saddle thatmay damage surrounding furniture. Weight capacity of book truck to be 400 lbs. Limited 12 Year Warranty with LIfetimeFrame Warranty

Finish: Navy

Manufacturer: BioFitModel Number: RBS33-07SapphireBlueDescription: Single Sided Multipurpose Cart, 3 Shelves, 47”H x 28”W x 13”D• Floor to Top of Lowest Tray or Shelf (in.): 9• Shelf Slope Angle (degrees): 12• Sloped Shelf Depth (in.): 7.5• Rugged 16-gauge, 1-inch diameter tubular steel

frame construction• 500-lb. weight capacity• Non-marring rubber wheels on ball-bearing casters

for smooth operation• Durable powder-coat finish

Options:

Finishes: Almond, Black, Gray, Sapphire Blue, Moss Green, Ruby Red

llucas

Typewritten Text

Not Approved: Dimensions do not match Specified Product

Item: US-1

TOTAL QUANTITY: 30


Manufacturer: LyonProduct Series: 8000 SeriesModel Number: 8021SH-starterDescription: 36"w x 18"d x 84"h, 20-Gauge Heavy Duty, Box "W" Shelves provide 900 lb. capacity, six (6) shelves, and “T” post upright.

Finish: Putty

Manufacturer: TennscoProduct Series: Q LineModel Number: OAP-84-MGY, Q-3624-S-MGY, SC-1S, ESB-1224-MGY, RSBU-MGYDescription: 36”W x 18”D x 84”H Open Style Shelving, 6 Shelves Per Unit, 20 GA Shelves with Stiffeners, Up to 850 lbs. Per Shelf, Units Not to Exceed 5000 lbs.

Options:

Finishes: Medium Grey, Sand, Light Grey

5 Shelf Unit Pictured6 Shelf Specified

llucas

Typewritten Text

Approved: Shelves to be single/stand alone unit

Item: US-2

TOTAL QUANTITY: 26


Manufacturer: LyonProduct Series: 8000 SeriesModel Number: 8082SHDescription: 36"w x 24"d x 84"h, 20-Gauge Heavy Duty, Box "W" Shelves provide 900 lb. capacity, six (6) shelves, and “T” post upright.

Finish: Putty

Manufacturer: TennscoProduct Series: Q LineModel Number: OAP-84-MGY, Q-3624-S-MGY, SC-1S, ESB-1224-MGY, RSBU-MGYDescription: 36”W x 24”D x 84”H Open Style Shelving, 6 Shelves Per Unit, 20 GA Shelves with Stiffeners, Up to 1000 lbs. Per Shelf, Units Not to Exceed 5000 lbs.

Options:



llucas

Typewritten Text


Item: US-3

TOTAL QUANTITY: 13


Manufacturer: LyonProduct Series: 8000 SeriesModel Number: 8005SHDescription: 36"w x12"d x 84"h, 20-Gauge Heavy Duty, Box "W" Shelves provide 900 lb. capacity, six (6) shelves, and “T” post upright.

Finish: Putty

Manufacturer: TennscoProduct Series: Q LineModel Number: OAP-84-MGY, Q-3612-MGY, ESB-1224-MGY, RSBU-MGYDescription: 36”W x 12”D x 84”H Open Style Shelving, 6 Shelves Per Unit, 20 GA Shelves, Up to 1000 lbs. Per Shelf, Units Not to Exceed 5000 lbs.

Options:



llucas

Typewritten Text


APPOQUINIMINK SCHOOL DISTRICT SILVER LAKE ELEMENTARY SCHOOL PROJECT NO. 18.019 FURNITURE, FIXTURES & EQUIPMENT

FURNISHINGS – SPECIFICATION SHEETS 12 00 00-34

ITEM #: LS-6A

ITEM: Library Double Face end Panel BASIS OF DESIGN: Liat or Approved Equal STYLE: Double Face End Panel MODEL #: EP-DV-4725 DIMENSIONS: 47 h. x 25 w. WOOD SPECIES: Maple DESCRIPTION: The end panels shall be constructed of 1-1/4” thick particleboard core with grade “A” veneer on both faces. The exposed edges shall be externally banded with a 1/8” solid hardwood. End panel must be able to be attached to cantilever shelving. Successful bidder must submit shop drawings to architect prior to order placement.

LOCATION/ROOM #’S QUANTITY


Media Center 132 12

TOTAL 12



ITEM #: LS-4

ITEM: Library Shelving BASIS OF DESIGN: Montel or Approved Equal STYLE: Aetnastak Double Faced Mobile Shelving w/ browsing book shelves and closed base MODEL #: Aetnastak Cantilever Mobile Shelving DIMENSIONS: 48 h. x 108 w. x 24 d. PAINT: To be Selected from full range of paint options LAMINATE: DESCRIPTION: Double faced steel cantilever shelving to have overall depth dimension of 24". Actual shelf depth is 11”. Provide three 36”W x 12”D x 7-1/2”H Browsing Box shelves per 36”W face for a total of (18) Browsing Box shelves. Provide top spreader tube which is full closed tube of 16-gauge, 2" x 2" square. Tube is securely electric welded with continuous upright columns. The length of the tube is 24". Provide a bottom spreader channel to be shaped, open to the floor and a minimum of 16-gauge steel. Spreader is to be electric welded on the two vertical faces with continuous welds to the upright columns. Slots in bottom spreader channel are provided to perform leveling function at the column. Top and bottom spreaders are electrically welded to the uprights with a full bead of each of the four joints. Shelving uprights to be completely closed, tubular, 16-gauge steel. Uprights shall have only a single row of slots in all conditions for mounting of one double sided or two single sided brackets in each hole. Each column is perforated full height with a row of slots spaced 1" on vertical centers to receive hooks and lugs of shelf brackets. In adjoining columns, the rows of slots are 5/8" on lateral centers. Two uprights are required for each section of a range. Mobile Base: Closed Base for Cantilever Shelving. The frame is recessed into the base for greater stability and rigidity. Each half-base shall be made of 12-gauge steel and shall be designed to hide the wheels. The 2-Piece Closed Base on wheels shall have four (4) 5” swivel wheels and shall be 6 1/4" high overall. Provide a one-piece high-pressure laminate canopy top with all necessary hardware. Laminate top shall be 1-1/4" thick 45lb. density particleboard core with .050" high-pressure laminate on face. Opposite face shall have backer. Exposed edges to be self-edge laminate. Where spliced, canopy tops shall have flush, butt joints not to exceed 1/16" and come equipped with tight-joint fasteners. Successful bidder must submit shop drawings to architect prior to order placement. .



Media Center 132 1

TOTAL 1



ITEM #: CH-08

ITEM: Stool

BASIS OF DESIGN: Media Technologies or Approved Equal STYLE: Hannah Stool MODEL #: HAN008 DIMENSIONS: Width 18 Depth 18 Height 35.5 Seat width 16.6 Seat depth 16.5 Seat height 24” Back width 18 Back height 13

FRAME COLOR: Silver 809 SHELL: TBD

DESCRIPTION: Hannah Stool with thermoplastic seat and back. Powder coated Frame. Meets or exceeds ASI/BIFMA atandards

COMMENTS:



T e c h / S t e m 1 3 4 8

T O T A L 8


BID FORM 00 41 13-7

SECTION 00 41 13

BID SUMMARY FORM

*THE FOLLOWING ITEMS LISTED MUST BE BID AS A GROUP* The total cost will be to provide, deliver, unpack, assemble and place the furniture in areas at times as designated in the attached Special Instructions, Specifications and General Instructions to Bidders.

All vendors must indicate their total bid price for the entire quantities of items listed below.

The award for each of these groups will be made to one vendor based on this total price. The furniture bid for each of these groups must be from the same manufacturer. Failure of a vendor to complete this section, failure to bid on furniture from the same manufacturer, or failure to bid on all items within the group, will result in an automatic rejection of a bid for any of the items within the group. The individual bid prices for each item listed on the bid form will be the prices paid by the School District if additional quantities are ordered.

GROUP A1:

The following items must be bid as a group: A-01

Indicate the total bid price for the entire quantities of items in Group A1 in the following space:

$

GROUP A2:


Indicate the total bid price for the entire quantities of items in Group A2in the following space:

$

GROUP A3:


Indicate the total bid price for the entire quantities of items in Group A3 in the following space:

$


BID FORM 00 41 13-8

GROUP B1:

The following items must be bid as a group: CH01, CH-02, CH-03, CH-04, CH-05

Indicate the total bid price for the entire quantities of items in Group B1 in the following space:

$

GROUP B-2:

The following items must be bid as a group: CH-06, CH-07, CH-08 Indicate the total bid price for the entire quantities of items in Group B2 in the following space:

$

GROUP B-3:

The following items must be bid as a group:

CH-09

Indicate the total bid price for the entire quantities of items in Group B3 in the following space:

$

GROUP B-4:

The following items must be bid as a group: CH-10, CH-11, CH-12, CH-13, CH-14, T-02 Indicate the total bid price for the entire quantities of items in Group B4 in the following space:

$


BID FORM 00 41 13-9

GROUP C:

The following items must be bid as a group: T-04

Indicate the total bid price for the entire quantities of items in Group C in the following space:

$

GROUP D:


FP-01 Indicate the total bid price for the entire quantities of items in Group D in the following space:

$

GROUP E:

The following items must be bid as a group: ML-01, T-03, LC-1 Indicate the total bid price for the entire quantities of items in Group E in the following space:

$

GROUP F1:

The following items must be bid as a group: N-01, N-02, N-03 Indicate the total bid price for the entire quantities of items in Group F1 in the following space:

$


BID FORM 00 41 13-10

GROUP F2

The following items must be bid as a group: N-04 Indicate the total bid price for the entire quantities of items in Group F2 in the following space:

$

GROUP G:


T-01 Indicate the total bid price for the entire quantities of items in Group G in the following space:

$

GROUP H:

The following items must be bid as a group: LS-1, LS-2, LS-3, LS-4, LS-5, LS-6, LS-6A, LS-7, LS-8 Indicate the total bid price for the entire quantities of items in Group H in the following space:

$

GROUP I:

The following items must be bid as a group: LS-09

Indicate the total bid price for the entire quantities of items in Group I in the following space:

$


BID FORM 00 41 13-11

GROUP J:

The following items must be bid as a group: LS-10A, LS-10B, LS-10C Indicate the total bid price for the entire quantities of items in Group J in the following space:

$

GROUP K:


M-01, M-02, M-03, M-04, M-05, M-06, M-07 Indicate the total bid price for the entire quantities of items in Group L in the following space:

$

GROUP L:

The following items must be bid as a group: P-1 Indicate the total bid price for the entire quantities of items in Group M in the following space:

$

GROUP M:


US-1, US-2, US-3 Indicate the total bid price for the entire quantities of items in Group N in the following space:

$


BID FORM 12 00 00-12

Item # Description Substituted Manufacturer

Substituted Product #

Unit Cost Qty.

Extended Cost

Group A1 – Art Rack

A-01 Drying Rack 2

TOTAL FOR GROUP A1 – Art Rack $ ______________________

Group A2 – Art Supplies

A-02 Ceramic Drying Cabinet 1

TOTAL FOR GROUP A2 – Art SUPPLIES $ ______________________

Group A3 – Art Storage

A-03 ToteTrays 40

TOTAL FOR GROUP A3 – Art STORAGE $ ______________________

Group B1 – Seating/Storage

CH-01 Task Chair (Office) 15

CH-02 Task Chair (Classroom) 51

CH-03 Task Chair (Conference) 28

CH-04 Guest Chair (Casters) 54


BID FORM 12 00 00-13



Unit Cost Qty.

Extended Cost

CH-05 Guest Chair 10

TOTAL FOR GROUP B1 – Seating $ ______________________

Group B2 - Seating

CH-06 Poly Stack Chair 13

CH-07 Poly Chair with Casters 74

CH-08 Poly Stool 8

TOTAL FOR GROUP B2 – Seating $ ______________________

Group B3 – Seating

CH-09 Poly Chair with Casters and Bookrack 16

TOTAL FOR GROUP B3 – Seating/Storage $ ______________________

Group B4 – Seating & Occ. Tables

CH-10 Diamond Lounge Chair 32

CH-11 Trapezoid Lounge Chair 8

CH-12 Boomerang Lounge Chair 1

CH-13 Triangle Lounge 23


BID FORM 12 00 00-14



Unit Cost Qty.

Extended Cost

CH-14 Round Ottoman 11

T-02 Occasional Table 4

TOTAL FOR GROUP B4 – Seating & Occasional Tables $____________________

Group C- Mobile Tables

T-04 Mobile Planning wood top 8

TOTAL FOR GROUP C –mobile tables $____________________

Group D – Fire Proof Files

FP-01 4 Drawer Fire Proof File 3

TOTAL FOR GROUP D –Fire Proof Files $____________________

Group E – Mobile Lectern/Work Tables/Cart

ML-01 Mobile Lectern 38

T-03 Planner Studio Table 4

LC-1 Metal Book Truck 2

TOTAL FOR GROUP E – Mobile Lectern/Work Tables/Cart $____________________


BID FORM 12 00 00-15



Unit Cost Qty.

Extended Cost

Group F1 – Nurse/Allied Health Furnishings

N-01 Recovery Couch 2

N-02 Storage Cart 3

N-03 Stool 3

TOTAL FOR GROUP F1 –nurse/allied health Furnishings $____________________

Group F2 – Nurse/Allied Health Furnishings

N-04 Treatment Table 1

TOTAL FOR GROUP f2 –nurse/allied health Furnishings $____________________

Group G – Tables

T-01 Table with Casters 6

TOTAL FOR GROUP g–Tables $____________________

Group H– Library Shelving

LS-1 Single Faced Shelving 19

LS-2 Single Faced Shelving 8

LS-3 Double Faced Shelving 12

LS-4 Double Faced Shelving with Browsing Book Shelves 1


BID FORM 12 00 00-16

LS-5 Single Face End Panel 10

LS-6 Single Face End Panel 2

LS-6A Double Face End Panel 12

LS-7 Custom Double Face End Panel 7

LS-8 Custom Double Face End Panel/Slat Wall 7

TOTAL FOR GROUP H–Library shelving $ ______________________

Group I– Book Drop

LS-09 Mobile Book Drop 1

TOTAL FOR GROUP I –Book Drop $ ______________________

Group J– Slat Wall Accessories

LS-10A Acrylic Sign Holder 10

LS-10B Large Book Holder 15

LS-03C Display Shelf 20

TOTAL FOR GROUP J – Slat Wall Accessories $ ______________________

Group K – Music Furnishings

M-01 Student Posture Chair 60

M-02 Music Stand 60

M-03 Chair Store Cart 1


BID FORM 12 00 00-17

M-04 Music Stand Cart 2

M-07 Choral Risers 5

M-08 Choral Riser Side Rails 1 Set

M-09 Choral Portfolio cabinet 2

TOTAL FOR GROUP K–Music furnishings $ ______________________

Group L– Podium

P-1 Podium 1

TOTAL FOR GROUP L–podium $ ______________________

Group M – Utility Shelving

US-1 18” D. Utility Shelving 30



TOTAL FOR GROUp M–Utility Shelving $ ______________________


BID FORM 12 00 00-18

TOTAL FOR All Furnishing $________________________________________________________________ Written Dollar Value:

List items or groups Not Included in Bid END OF BID FORM

Documents

ADDENDUM to CONTRACT DOCUMENTS - Delaware