Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
Acton Campus
Building 38
Hazardous Materials Report
This document is uncontrolled once printed.
You must consult the individual Building
Register prior to work commencing.
Contents Page 1. Revision Table
2. ANU Hazardous Materials Register
3. ANU Hazardous Materials Maintenance Log
4. Robson Environmental Report Dated March 2019
5. Future Inspection Reports and Certificates
1. Revision Table – Building 38
Rev.
Nature of changes
Approval
Date
1 Original Report Generated
Building 38 Physics Building
Robson Environmental
25/03/2019
2 Vinyl Floor Tiles Material Analysis Report Generated Building 38 Physics Building – Rooms 163 and 164
Robson Environmental
14/06/3019
3
4
5
6
7
2. ANU Hazardous Materials Register
Site Location: Building 38 Physics BuildingAssessor: Jordan Curbishley & Andrew Dibb - Robson
A2628 CHRYRefer to Robson report
Sheet Building 38 Physics Building Store G.30 - Wall 1 1 2 2 2 8 L 21 m2Encapsulate. Label and maintain in a good
condition. Inspect every 5 years. Remove prior to demolition or refurbishment.
A2630 CHRYRefer to Robson report
Mastic Building 38 Physics Building ceiling space - Joints to ductwork 1 1 1 2 2 4 L -Label and maintain in a good condition. Inspect every 5 years. Remove prior to demolition or
refurbishment.
Refer to A2630 CHRYRefer to Robson report
Mastic Building 38 Physics Building Plant Room G.16A - Joints to HVAC 1 1 1 2 2 4 L -Label and maintain in a good condition. Inspect every 5 years. Remove prior to demolition or
refurbishment.
A2633 AMO, CHRYRefer to Robson report
Cement Sheet Building 38 Physics Building - Radioactive Store B.04 - Caps to furnace devices 1 1 1 2 2 4 L 2 units Remove.
A2634 AMORefer to Robson report
Pipe Lagging Debris Building 38 Physics Building area adjacent access point and air compressor - To surfaces 2 3 3 2 2 72 H - Remove. Prohibit access.
A2638 CHRYRefer to Robson report
Rope Seal Building 38 Physics Building Lift 1.01E - Seal 2 1 2 2 2 16 L 3 lin mLabel and maintain in a good condition. Inspect every 5 years. Remove prior to demolition or
refurbishment.
A2640 AMORefer to Robson report
Pipe Lagging Debris Building 38 Physics Building tunnel to Psychology Building - To surfaces 2 3 3 2 2 72 H - Remove. Prohibit access.
Presumed -Refer to Robson report
Pipe Lagging Building 38 Physics Building Mens Toilet G.31 - To pipes embedded in masonary walls 2 1 1 1 2 4 L - Further intrusive investigation required prior to
possible disturbance.
A2626 NADRefer to Robson report
Sheet Building 38 Physics Building Store G.30C - Infill panel above door - - - - - - Nil - No further action required.
A2627 NADRefer to Robson report
Sheet Building 38 Physics BuildingSotre G.30B - Infill panel above grated windor and ceiling - - - - - - Nil - No further action required.
A2629 NADRefer to Robson report
Vinyl Floor Tile Building 38 Physics Building Access to subfloor G.02C - Green vinyl floor tile - - - - - - Nil - No further action required.
A2631 NADRefer to Robson report
Vinyl Floor Tile Building 38 Physics Building Office 1.60 - Green hessian backed vinyl floor tile - - - - - - Nil - No further action required.
A2632 NADRefer to Robson report
Vinyl Floor Tile Building 38 Physics Building Lift 1.01E - Grey flecked vinyl floor tiles - - - - - - Nil - No further action required.
Phot
o ID
Reinspection Date: February 2024 or as specified within commentsInspection Date: Robson Environmental - 18-19 February 2019
Ris
k Sc
ore
Act
ion
Prio
rity
Qua
ntity
(m, m
2, m
3)
Actions/Comments
Asb
esto
s Ty
pe
Con
ditio
n
Acc
essi
bilit
y
Airb
orne
Pot
entia
l
Expo
sure
Pot
entia
l
Description Location
No Asbestos Detected
Asbestos Containing Materials
Sample No.
Res
ults
A2636 NADRefer to Robson report
Sprayed Coating Building 38 Physics Building Exterior - To column - - - - - - Nil - No further action required.
A2637 NADRefer to Robson report
Sheet Building 38 Physics Building Lift Motor Room B.04 - Switchboard backing - - - - - - Nil - No further action required.
A2639 NADRefer to Robson report
Sprayed Coating Building 38 Physics Building Plant Room G10 - To ceiling pipes - - - - - - Nil - No further action required.
A2641 NADRefer to Robson report
Sheet Building 38 Physics Building Bridge to Building 38B - Fascia panels to inside and outside - - - - - - Nil - No further action required.
C1621 NADRefer to Robson report
Vinyl Floor Tile Building 38 Physics Building Room 163 - Green vinyl floor tiles - - - - - - Nil - No further action required.
C1622 NADRefer to Robson report
Vinyl Floor Tile Building 38 Physics Building Room 164 - Beige vinyl floor tiles - - - - - - Nil - No further action required.
C1623 NADRefer to Robson report
Vinyl Floor Tile Building 38 Physics Building Room 164 - Green vinyl floor tiles - - - - - - Nil - No further action required.
A2635 (PB1294) 0.8%Refer to Robson report
Orange Paint Building 38 Physics Building Exterior Loading Dock - Fire Extinguisher Case - - - - - - M - Encapsulate. Maintain in good condition.
ODS731 R-22Refer to Robson report
APAC Heat Pump Building 38 Physics Building Exterior - - - - - - L 1 no Maintain. Manage during demoliton or refurbishment.
ODS724 R-22Refer to Robson report
Daikin Building 38 Physics Building Exterior - - - - - - L 2 no Maintain. Manage during demoliton or refurbishment.
ODS733 Presumed R-22
Refer to Robson report
Carrier Building 38 Physics Building Exterior - - - - - - L 2 no Maintain. Manage during demoliton or refurbishment.
ODS728 R-22Refer to Robson report
APAC Heat Pump Building 38 Physics Building Plant Room G10 - - - - - - L 3 no Maintain. Manage during demoliton or refurbishment.
SMF1182 SMFRefer to Robson report
Suspended Ceiling Tiles Building 38 Physics Building ceilings throughout - Ceiling tiles - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1176 SMFRefer to Robson report
Insulation Building 38 Physics Building Plant Room G.16A - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF Containing Materials
Lead Paint Systems (Sampled materials found to be above the threshold criteria of 0.1% by w/w)
PCB Containing Materials
ODS Containing Materials
Lead Free Paint Systems (Sampled materials found to be below the threshold criteria of 0.1% by w/w)
Lead Dust
Lead Free DustNo Lead Dust Samples Taken.
No Lead Free Dust Samples Taken.
No Lead Free Paint Systems Sampled.
No PCB Containing Materials Identified
Lead Soils (Sampled materials found to be above the ASC NEPM (2013) HIL A site assessment criteria of 300 mg/kg)
Lead Free Soils (Sampled materials found to be below the ASC NEPM (2013) HIL A site assessment criteria of 300 mg/kg)No Lead Soil Samples Taken.
No Lead Free Soil Samples Taken.
SMF1165 SMFRefer to Robson report
Seal Building 38 Physics Building Store G.30 - To door of flammable liquids cupboard - - - - - - L - Maintain. Manage during demoliton or
refurbishment.
SMF1168 SMFRefer to Robson report
Insulation Building 38 Physics Building Plant Room G.10 - Rheem electric hot water unit - - - - - - L - Maintain. Manage during demoliton or
refurbishment.
SMF1169 SMFRefer to Robson report
Insulation Building 38 Physics Building riser cupboard 1.01A - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1172 SMFRefer to Robson report
Insulation Building 38 Physics Building ceiling space - Loose insulation - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1173 SMFRefer to Robson report
Insulation Building 38 Physics Building riser cupboard 1.01J - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1177 SMFRefer to Robson report
Insulation Building 38 Physics Building riser cupboard 1.80A - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1184 SMFRefer to Robson report
Insulation Building 38 Physics Building riser cupboard 1.01G - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1178 SMFRefer to Robson report
Insulation Building 38 Physics Building Plant Room G.16A - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1179 SMFRefer to Robson report
Insulation Building 38 Physics Building ceiling space - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1180 SMFRefer to Robson report
Insulation Building 38 Physics Building riser cupboard 1.01I - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1181 SMFRefer to Robson report
Insulation Building 38 Physics Building ceiling space - To ductwork - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1183 SMFRefer to Robson report
Insulation Building 38 Physics Building ceiling space - Sisalation to roof - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1175 SMFRefer to Robson report
Insulation Building 38 Physics Building riser cupboard 1.01D - To pipe work - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1162 SMFRefer to Robson report
Insulation Debris Building 38 Physics Building B.01 - Debris - - - - - - L - Maintain. Manage during demoliton or refurbishment.
SMF1166 SMFRefer to Robson report
Insulation Building 38 Physics Building B.01 - To pipes - - - - - - L - Maintain. Manage during demoliton or refurbishment.
Above-ground and Underground Storage TanksNo Above Or Underground Storage Tanks Identified.
3. ANU Hazardous Materials Maintenance Log
Hazardous Materials Maintenance Log
Site: Building 38
ANU Hazardous Materials Maintenance Log The following log should be maintained by the responsible person. It should contain information relating to the on-going maintenance or control measures associated with ACM including removal, remedial works, repairs, inspection, monitoring and clearance details etc.
Site: Building 38 Date Scope/Location Carried out by Result/Comments Entered by 25/03/2019 Hazardous Materials Survey & Register Jordan Curbishley & Andrew
Dibb – Robson Environmental Hazardous Materials Survey & Register produced and delivered
Jordan Curbishley – Robson Environmental
14/06/2019 Vinyl Floor Tiles Material Analysis Report Jordan Curbishley – Robson Environmental
Uncovered vinyl floor tiles in Rooms 163 and 164 assessed and tested. Material Analysis Report produced and delivered.
Jordan Curbishley – Robson Environmental
20/06/2019 Hazardous Materials Survey & Register Jordan Curbishley – Robson Environmental
Hazardous Materials Survey & Register updated to incorporate VFT Material Analysis Report.
Jordan Curbishley – Robson Environmental
4. Robson Environmental Report
This report MUST NOT be used as a removal specification Client: ANU, The Australian National University, Canberra, ACT, 2601
Accredited for compliance
with ISO/IEC 17020 Robson Environmental Pty Ltd ~ ABN: 55 008 660 900 ~ www.robsonenviro.com.au p: 02 6239 5656 ~ f: 02 6239 5669 ~ [email protected] PO Box 112 Fyshwick ACT 2609 ~ 140 Gladstone Street Fyshwick ACT 2609
H2203_T-07207_Building 38 - Physics Building-20190218
Hazardous Materials Survey & Management Plan Building 38 - Physics Building The Australian National University Acton ACT 2601
February 2019
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 2 of 94
CERTIFICATE OF APPROVAL FOR ISSUE OF DOCUMENTS
Document No: H2203 Revision Status: 1 Title: Hazardous Materials Survey Date of Issue: 23/03/2019 Building 38 - Physics Building The Australian National University Acton ACT 2601
Client: ANU Copy No: One
Assessor Position Signature
Surveyed by:
Jordan Curbishley - Licensed Asbestos Assessor #AA00039
Andrew Dibb - Licensed Asbestos Assessor #AA00030
Hazardous Materials Consultant
Hazardous Materials
Consultant
Approved by: Anne Robson - Licensed Asbestos Assessor #AA00022 Director
Released by: Anne Robson - Licensed Asbestos Assessor #AA00022 Director
RELEASE STATUS:
Confidential
© Copyright Robson Environmental Pty Ltd
All intellectual property and copyright reserved.
This report remains the property of Robson Environmental Pty Ltd (“Robson”). The person commissioning the report (“the client”) is entitled to retain possession of it upon payment of Robson’s fees or upon arrangements as to payment satisfactory to Robson has been made.
Apart from any fair dealing for the purpose of private study, research, criticism or review, as permitted under the Copyright Act, 1968 the client may not photocopy or otherwise reproduce, transmit, store in a retrieval system or adapt in any form or by any means (electronic, mechanical, photocopying, recording or otherwise) all or any part of this report without the prior written consent of Robson.
In the event that the client photocopies or otherwise reproduces all or any part of this report without the prior written consent of Robson then the client:
a) must immediately upon demand of Robson return to Robson the original (or, if more than one , all originals) and all photocopies or other reproductions of the report;
b) agrees to pay Robson any loss or damage suffered as a result of the breach by the client of this provision; and c) agrees to indemnify Robson against any liability arising from the breach by the client of this provision.
Enquiries should be addressed to Robson Environmental Pty. Ltd.
This report is solely for the use of the client and may not contain sufficient information for purposes of other parties, or for other uses. Any reliance on this report by third parties shall be at such party’s own risk. This report shall only be presented in full and may not be used to support any other objective than those set out in the report, except where written approval with comments are provided by Robson Environmental Pty Ltd.
DISTRIBUTION
Organisation Attention Copy No. Actioned
ANU Brett Morrison 1 23/03/2019
Robson Environmental Pty Ltd John Robson 2 23/03/2019
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 3 of 94
TABLE OF CONTENTS 1 PREFACE .......................................................................................................... 5
2 EXECUTIVE SUMMARY .................................................................................... 6
2.1 Purpose 6
2.2 Scope 6
2.3 Survey Methodology 6
2.4 Key Findings 9
2.5 Key Recommendations 13
3 INTRODUCTION .............................................................................................. 18
3.1 Requirements for the HMSMP 18
3.2 Exclusions 19
3.3 Limitations 21
4 ASBESTOS SURVEY RESULTS .................................................................... 22
4.1 Survey Details 22
4.2 Survey Methodology 22
4.3 Sample Analysis 22
4.4 Risk Assessment 23
4.5 Asbestos Register 26
5 LEAD PAINT SURVEY RESULTS ................................................................... 29
5.1 Introduction 29
5.2 Results 29
5.3 Discussion and Conclusion 30
6 SYNTHETIC MINERAL FIBRE (SMF) SURVEY RESULTS ............................ 31
6.1 Introduction 31
6.2 Results 31
6.3 Conclusion 32
7 POLYCHLORINATED BIPHENYLS (PCB) SURVEY RESULTS .................... 33
7.1 Introduction 33
7.2 Results 34
8 OZONE DEPLETING SUBSTANCES SURVEY RESULTS ............................ 35
8.1 Results 36
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 4 of 94
9 FUEL STORAGE FACILITIES ......................................................................... 37
9.1 Results 37
10 ASBESTOS MANAGEMENT ........................................................................... 38
10.1 Management of ACM 38
10.2 Management of Contractors 39
10.3 Asbestos Emergency Procedures 40
10.4 PMCW Decision Record 41
10.5 Timetable for Action 42
11 RESPONSIBILITIES ........................................................................................ 43
11.1 Asbestos - Provision of Information 43
11.2 Updating the Risk Assessment 44
11.3 Key Personnel 45
12 ASBESTOS REMOVAL WORKS .................................................................... 46
12.1 PMCW Responsibilities 46
12.2 Removalist Responsibilities 46
12.3 Licensing Requirements 46
12.4 Approval to Begin Asbestos Removal Works 47
12.5 Emergency Work in Areas Containing Asbestos 47
12.6 Monitoring Arrangements 47
12.7 Clearance Inspections 48
12.8 ACM removal/maintenance record 48
13 FURTHER INFORMATION .............................................................................. 50
13.1 Useful Contacts 50
14 APPENDICES .................................................................................................. 51
14.1 APPENDIX A – Laboratory Reports 51
14.2 APPENDIX B – Plans 60
14.3 APPENDIX C – HAZMAT Item locations & representative photographs 64
14.4 APPENDIX D – Hazardous Material Management Information 81
15 GLOSSARY ..................................................................................................... 92
16 REFERENCES ................................................................................................. 94
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 5 of 94
1 PREFACE
This Hazardous Materials Survey and Management Plan (HMSMP) was commissioned by ANU in order to assure the occupants of the site the highest standards of occupational health and safety in relation to hazardous materials. The safe removal of hazardous materials must be undertaken by appropriately licensed and skilled personnel prior to the demolition of the premises.
The HMSMP contains sections covering the identification, evaluation and control of hazardous materials including asbestos containing materials (ACM), Lead Paint, Polychlorinated Biphenyls (PCB), Synthetic Mineral Fibre (SMF), Ozone Depleting Substances (ODS) and fuel storage above and underground storage tanks (A/UST).
Robson Environmental Pty Ltd commenced the hazardous material survey on 18 February 2019 to 19 February 2019. The information contained in this document will assist the PMCW (person with control or management of a workplace) in fulfilling their obligations under the latest editions of the following regulations/Acts:
How To Manage and Control Asbestos In The Workplace Code of Practice
How To Safely Remove Asbestos Code of Practice
Dangerous Substances (General) Regulation 2004
Dangerous Substances Act 2004
Work Health and Safety Act 2011
Work Health and Safety Regulations 2011
National Code of Practice for the Safe Use of Synthetic Mineral Fibre [NOHSC:2006(1990)]
National Standard for Synthetic Mineral Fibres [NOHSC:1004(1990)]
Guide to Hazardous Paint Management Part 2: Lead paint in residential, public and commercial buildings Standards Australia, AS 4361.2 – 2017
Identification of PCB-Containing Capacitors; An information Booklet for Electricians and Electrical Contractors ANZECC 1997 and
The Australian Refrigeration and Air-conditioning Code of Good Practice Standards Australia, HB 40.1 – 2001
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 6 of 94
2 EXECUTIVE SUMMARY
2.1 Purpose
This report presents the findings of a Hazardous Materials survey conducted at the site on 18 February 2019 to 19 February 2019 at the request of the client. The survey was undertaken to assess the extent and condition of hazardous materials and document safe management procedures in accordance with current legislation. The safe removal of hazardous materials must be undertaken by appropriately licensed and skilled personnel prior to refurbishment or demolition of the premises or where the risk assessment recommends removal. This report includes information which must be known and acted upon prior to the commencement of any demolition, refurbishment, or hazardous material removal or remediation. It also details responsibilities that the PMCW (person with management or control of a workplace) and occupier must address to ensure safe occupation of the premises.
2.2 Scope
The Hazardous Materials survey was non-destructive and non-intrusive in nature with the extent limited to the following areas:
Interior and exterior of the building Roof, amenities and immediate surrounding land A/UST filler points and breather vents
This report outlines only the hazardous material categories specified. Other hazards are present in this building including but not limited to ionising radiation and high intensity electromagnetic laser radiation. This document must NOT be treated as a comprehensive list of all hazards present. Please contact ANU representatives for further details.
The survey did not include the inspection or assessment of the following areas: Subterranean areas (e.g. infill/soil) Concealed cavities Formwork and subterranean electrical cable ducts and water pipe ducts
2.3 Survey Methodology
The survey involved the visual inspection of accessible, representative, construction materials and the collection and analysis of sampled materials suspected of being potentially hazardous to human health.
Hazardous materials assessed included ACM, SMF, PCBs, lead containing paint, ODS and A/UST.
The site inspection included the sampling of representative materials suspected of being hazardous, was undertaken in accordance with Robson’s NATA ISO/IEC 17020 accreditation, ISO9001, ISO14001, AS4801 and current legislation. The particular sampling methodology used for each hazardous materials type is provided below:
Asbestos: The asbestos materials survey was conducted in accordance with the current legislation. It involved a visual inspection of accessible representative construction materials
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 7 of 94
suspected of containing asbestos. Materials were not sampled from all areas due to the uniformity of the materials used throughout the building(s). Samples were analysed in Robson Environmental’s National Association of Testing Authorities (NATA) accredited laboratory for the presence of asbestos by polarising light microscopy and dispersion staining.
Note that electrical switchboards and other similar areas were only inspected where they were isolated by a qualified electrician. Live switchboards were not inspected, and accordingly are presumed to be ACM until conclusively proven otherwise.
Lead (Pb) Based Paints: Paint was tested during the hazardous materials survey using 3M™ LeadCheck™ Swabs which have a detection limit of 0.06% w/w lead, sufficient to classify paint as lead free under AS4361.2-2017. Where requested by the client, deemed prudent by the assessor, or required due to inconclusive results from this test, representative paint samples were also collected in accordance with AS4361.2-2017 and analysed for lead content. In general however as the detection limit of 0.06% w/w lead is only slightly lower than the threshold for lead paint of 0.10% lead set out in AS4361.2-2017 it is generally satisfactory to treat a positive result with 3M™ LeadCheck™ Swabs as being indicative of lead paint, obviating the need for further sampling and analysis.
The sampling criterion provided below is taken from AS4361.2-2017 Section A4 Sampling Strategy clauses (a, b, c);
(a) An adequate number of sample sites should be analysed to properly characterise the paint systems present on site.
(b) For small surfaces such as architraves, windows and doors and cupboards, a single sample may suffice.
(c) For large, uniformly painted surface areas such as the exterior facade of high rise buildings, or for interior walls and ceilings of large rooms, and where laboratory testing is employed, composite samples should be taken from three separate locations in 10m² sections.
Collected paint samples were analysed for their lead (Pb) content by Envirolab Services Pty Ltd – NATA accreditation number: 2901 using ICP/AES techniques and in-house Method No.4.
Within the same building, wherever a paint coating had a similar surface texture, colour, etc. to a paint coating that had already been sampled because of its suspected lead content, it was presumed that these paint coatings were identical. However, results can only be guaranteed valid for directly tested/sampled paints (especially due to deliberate attempts to match new paint to existing coatings in some applications).
SMF: Synthetic Mineral Fibre (SMF) materials were visually identified and a determination made as to whether they were bonded or un-bonded.
PCBs: The information (make, type, capacitance etc.) recorded for each representative fluorescent light fitting capacitor suspected of containing PCB was cross-referenced against ANZECC Identification of PCB Containing Capacitors – Information Booklet for Electricians and Electrical Contractors - 1997.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 8 of 94
This identification booklet provides a list of electrical equipment that is known to contain PCBs, and a list of electrical equipment known not to contain PCBs. Where the information recorded from the capacitor case(s) correlated exactly with the information listed in the ANZECC Information Booklet for known PCB-containing capacitors it was determined that PCBs were present in the capacitor under analysis.
Wherever a capacitor could not be identified in either list, this was noted in the PCB register as being a capacitor suspected to contain PCBs.
Note that light fittings were only inspected where they were isolated by a qualified electrician. Live light fittings were not inspected, and accordingly no determination about whether or not they contain PCB is included in this report.
Ozone Depleting Substances: A visual examination was made of refrigerant gas labels affixed to representative air-conditioning and refrigeration units. Information concerning the ASHRAE/ARI refrigerant designated R number was noted for later cross-reference to relevant air-conditioning and refrigeration industry Codes of Practice and Guidelines. In addition, the condition of the plant was noted and comment made as to possible refrigerant or lubricant leaks.
Where refrigerant gas labels were absent from representative air-conditioning and refrigeration plant, an assessment was made as to the likelihood of the plant using an ozone depleting substance based on its age and condition.
Fuel Storage Facilities: The survey included a visual inspection for above ground storage tanks (AST) and underground storage tank (UST) filler points and breather vents.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 9 of 94
2.4 Key Findings
Asbestos Table 1A: ACM locations and required actions
Building 38 - Physics Building ACM Locations Action to be taken
Pipe lagging debris
(Friable)
LB area adjacent access point and air compressor - to surfaces
Remove Prohibit access
Mastic (Non-Friable)
L2 ceiling space - joints to HVAC ductwork
Label and maintain Inspect every 5 years Remove prior to demolition
Rope seal (Friable)
L1 Lift - door seal
Label and maintain Inspect annually Remove prior to demolition
Pipe lagging (fibrous)
(Presumed Friable)
L1 Men G.31 - pipe lagging Further investigation required prior to possible disturbance
Mastic (Non-Friable)
L1 Plant Room G.16A - joints to HVAC ductwork
Label and maintain Inspect every 5 years Remove prior to demolition
Cement sheet (Non-Friable)
LB Radioactive Store B.04 - cap to furnace device Remove
Sheet (Non-Friable)
L1 Store G.30 - wall
Label and maintain Inspect every 5 years Encapsulate Remove prior to demolition
Pipe lagging debris
(Friable) LB tunnel to Building 39 - to pipes
Remove Prohibit access
Refer to Section 2.4 - Table 1B for presumed ACM and Section 3.2 for exclusions
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 10 of 94
Table 1B: Presumed ACM, concealed locations and required actions
Type ACM Locations Action to be taken
The materials listed below while not identified on site, should be presumed to be present until a destructive survey confirms otherwise
Presumed ACM
Insulation/pipe lagging
Inaccessible ducts, risers and ceiling and wall space cavities
Destructive survey under controlled conditions prior to any refurbishment which is likely to disturb possible ACM in these areas. Until these areas are surveyed they should be presumed to contain asbestos. No access to unauthorised personnel should be given
Asbestos millboard lining
Interior of air conditioning ductwork adjacent to heater elements
Asbestos insulation and gaskets/joints
Within mechanical equipment concealed by outer metal cladding, structure or housing
Asbestos vinyl floor tiles, covering, cushioning underlay and adhesive
Found beneath carpets and vinyl flooring
Asbestos sheeting
Backing material to ceramic tiles (roofs, floors and walls) and packers to building construction joints, such as gable end verge undercloaking
Asbestos cement sheet formwork and electrical cable duct / water pipe
Subterranean areas
Prior to any planned demolition, refurbishment or maintenance, its effect upon any in situ asbestos must be established by reference to this document including amendments.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 11 of 94
Lead Paint
It should be assumed that all similar paints throughout the building contain comparable percentages of lead.
Lead Paint (>0.1%) - Building 38 - Physics Building
Location Paint Colour Required action
Exterior loading dock - fire extinguisher case Orange Encapsulate
Synthetic Mineral Fibre (SMF)
It should be presumed that SMF materials may be present to inaccessible areas.
Building 38 - Physics Building
Material Location & Material Required action
Suspended ceiling tiles Ceilings throughout Maintain
Seal to door of flammable liquids cupboard L1 Store G.30 Maintain
Rheem electric hot water unit L1 Plant Room G.10 Maintain
Insulation to pipe work L1 Plant Room G.16A Maintain
Insulation to pipe work L2 riser cupboard 1.01A Maintain
Loose insulation L2 ceiling space Maintain
Insulation to pipe work L2 riser cupboard 1.01J Maintain
Insulation to pipe work L2 riser cupboard 1.01D Maintain
Insulation to pipe work L2 riser cupboard 1.80A Maintain
Insulation to ductwork L2 Plant Room G.16A Maintain
Insulation to pipe work L2 ceiling space Maintain
Insulation to pipe work L2 riser cupboard 1.01I Maintain
Insulation to ductwork L2 ceiling space Maintain
Sisalation L2 ceiling space Maintain
Insulation to pipe work L2 riser cupboard 1.01G Maintain
Insulation debris LB B.01 Remove
To pipes LB B.01 Maintain
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 12 of 94
Polychlorinated Biphenyls (PCB) Make - Type Location Total Required action
Light fittings visually assessed as being new. Prior to any works that may affect fluorescent light fittings full access should be provided by a licensed electrician to determine if PCBs are present.
* Note that light fittings were only inspected where they were isolated by a qualified electrician. Live light fittings were not inspected, and accordingly no determination about whether or not they contain PCB is included in this report.
Ozone Depleting Substances (ODS)
ODS - Building 38 - Physics Building
R Number Location Total Required action
R-22 Exterior, Daikin 2 no Maintain
R-22 Exterior, APAC heat pump 1 no Maintain
Presumed R-22 Exterior, Carrier 2 no Maintain
R-22 L1 Plant Room G.10, APAC heat pump 3 no Maintain Non – Ozone Depleting Substances
Building 38 - Physics Building
R Number Location Total Required action
R-32 Exterior, Daikin Inverter 3 no No action required
R-410A Exterior, Daikin Super Inverter 7 no No action required
R-410A Exterior, Mitsubishi Inverter 1 no No action required Above Ground Storage Tanks (AST) & Underground Storage Tanks (UST)
A/UST Location Total Required action
No storage tanks located
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 13 of 94
2.5 Key Recommendations
Asbestos
This building is joined structurally to Buildings 38A and 38B, and the basement (LB) tunnel network joins to Building 39 (Psychology). Reference must be made to these reports for a full understanding of hazardous materials in this building.
Pipe lagging debris was found to several locations within the basement. Access to the basement must be prohibited until a full environmental clean has been carried out by licensed Asbestos Removalists and a clearance certificate issued by a licensed Asbestos Assessor. Note that in situ lagging is known to be present to one of the pipes passing above the door in the tunnel network that separates Buildings 38 and 39. This are must not be disturbed - refer to the relevant documentation for Building 39 for further details.
The lift doors are made of several pieces of fabric. Where the pieces meet when the door closes the gap is sealed with asbestos wrapped in a fabric outer layer. This ACM is extremely friable, with release of respirable fibres possible as a consequence of minor disturbance. Consideration should be given to the removal of this material. If it is to remain in situ it must be thoroughly inspected on an annual basis to ensure the asbestos core is not exposed. If it becomes exposed it must be sealed by a licensed Asbestos Removalist. If the lift is in active use these annual inspections should include a check that operation of the doors does not cause the seal to rub excessively in a manner that could lead to the release of fibres or damage to the outer fabric wrap. All similar lift doors must be presumed to utilise the same asbestos containing seals.
Devices suspected of being furnaces are stored in the Radioactive Store in the basement. The caps of these devices were found to contain asbestos. If it is safe to do so (taking into account possible radiation hazards) the devices should be removed whole by a licensed Asbestos Removalist.
The wall of Store G.30 was found to contain asbestos. It is informally labelled. It should be sealed with paint and labelled as containing asbestos in accordance with ANU guidelines.
The mastic to the HVAC ductwork in the ceiling space was found to contain asbestos. All mastic to HVAC ductwork throughout the building must be presumed to contain asbestos. This material presents a very low exposure risk and may remain in situ provided it is maintained and not disturbed.
Due to the age of the building and its construction it must be presumed that asbestos containing pipe lagging is present to hot water pipes embedded in masonry walls. Taps and other fixtures to such areas must not be removed. Prior to works which may disturb these areas access and water supply must be isolated and a licensed Asbestos Assessor engaged to conduct an intrusive investigation.
ACM must not be drilled, cut, sanded, damaged or abraded and a good paint finish maintained. Asbestos work on non friable ACM may be undertaken by a licensed Class A or B Asbestos Removalist. Any works on, or in the vicinity of friable ACM
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 14 of 94
must only be undertaken by a licensed Class A Asbestos Removalist.
Any ACM identified in this report that is to remain in situ should be inspected by a licensed Asbestos Assessor at the intervals stated in Section 4.5 Table 3A Asbestos Register.
As access could not be gained to all areas of the building, it should be presumed that any similar materials located within these areas could contain asbestos until proven otherwise. Strict controls should be put in place to brief all contractors.
ACM should be labelled with approved asbestos warning labels or signs. Due to the stigma associated with asbestos and to avoid malicious damage to ACM, labelling can be kept to discrete areas. Where labelling cannot be undertaken, the PMCW must adopt strict administrative controls to ensure ACM is not subject to accidental damage.
Asbestos Removal
Removal of ACM must be undertaken by a licensed Asbestos Removalist in accordance with current legislation. The removal/remediation of friable ACM must be undertaken by a licensed Class A Asbestos Removalist. Removal or remediation of non friable asbestos may be undertaken by either an A or B Class Asbestos Removalist.
Prior to the commencement of any removal or remediation works associated with any amount of friable or non friable asbestos a building certifier must be engaged and building approval granted. An application must be submitted to WorkSafe ACT and ComCare (where applicable) at least 5 days prior to removal works commencing. An asbestos removal contractor must supply an Asbestos Removal Control Plan (ARCP) and a Safe Work Method Statement (SWMS). An independent licensed Asbestos Assessor should be engaged to ensure that the ARCP addresses all safety issues relating to the planned asbestos works.
Air monitoring is mandatory during the removal or remediation of friable asbestos and should be considered during the removal or remediation of non friable asbestos. Air sampling is to be undertaken in accordance with the Guidance Note on the Membrane Filter Method for Estimating Airborne Asbestos Fibres, 2nd Edition and test certificates should be NATA endorsed.
An independent Asbestos Assessor must also be employed to undertake a Clearance Inspection of both friable and non friable asbestos removal or remediation works. A satisfactory clearance certificate for the remediated areas must ensure that no visible asbestos or presumed asbestos remains. Additionally no asbestos fibres should be detected by laboratory analysis if any validation samples are taken. All surfaces within the remediated area must be free of general dust and debris.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 15 of 94
Lead Paint
It is recommended that lead paint be maintained. Any areas that begin to flake, peel or otherwise deteriorate should be appropriately remediated. If the paint is to be removed this should be undertaken by a suitably qualified person.
It should be assumed that all similar paint applications throughout the building would contain similar percentages of lead.
Refer to Appendix D for further general information on lead paint.
SMF
SMF debris was observed within the basement area. This should be removed.
SMF are also present within the insulation to pipes in risers and the basement (LB) area, the hot water heaters, the HVAC ductwork, the door seal to the flammable goods cupboard, and the ceiling space (as loose insulation and foil backed insulation to the underside of the roof). These materials may remain in situ providing they are maintained.
If these materials are to be disturbed during refurbishment appropriate PPE and RPE should be worn. SMF materials being removed should be done so using effective dust control procedures.
Refer to Appendix D for further general information on SMF.
PCBs
Light fittings visually assessed as being new. Prior to any works that may affect fluorescent light fittings full access should be provided by a licensed electrician to determine if PCBs are present.
Refer to Appendix D for further general information on PCB.
ODS
No tags identifying the refrigerant charge in the Carrier units mounted to the side of building were visible from ground level. Based on the likely age of the units and advice from ANU Facilities and Maintenance personnel it must be presumed that they contain ODS unless proven otherwise. All remaining ODS and non ODS were positively identified by tags affixed to the units.
All refrigeration and air-conditioning plant should be regularly checked and maintained in accordance with the manufacturer guidelines.
Refer to Appendix D for further general information on ODS.
A/UST
No A/UST located.
Refer to Appendix D for further general information on A/UST.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 16 of 94
Legislation and Guidelines (UST): Section 3.2 of AS4976 (2008) The Removal and Disposal of Underground Petroleum Storage Tanks, states that the out-of-service period for a A/UST should not exceed that laid down in any applicable regulation and should not normally be greater than twelve (12) months. Also, Section 6 (Decommissioning) of the ACT EPA (2009) Environmental Guidelines for Service Station Sites and Hydrocarbon Storage indicates that all decommissioned tanks must be removed unless there are specific operational or structural reasons as to why they must remain. These reasons must be outlined or substantiated by an experienced and competent person.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 17 of 94
Demolition and Refurbishment
Robson Environmental Pty Ltd recommends that prior to any demolition our office be contacted. Our licensed Asbestos Assessors can attend the site to observe the demolition process, advise as necessary and in the event of previously inaccessible hazardous materials being located, assist with assessing the extent, type and removal or abatement of materials as required.
Robson Environmental Pty Ltd provides a range of occupational hygiene services in relation to the safe remediation or abatement of hazardous materials as well as contaminated land advice in relation to hydrocarbon contamination.
To assist with the tendering process Robson Environmental could be engaged to attend the walkthrough to show the extent of ACM and to respond to questions of clarification.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 18 of 94
3 INTRODUCTION
The following Hazardous Materials Survey and Management Plan (HMSMP) has been designed to address the safe control of hazardous materials. It covers current requirements for hazardous material management as at 18/02/2019 to 19/02/2019 only and must therefore be updated to comply with any future changes to legislative requirements. The safe removal of hazardous materials must be undertaken by appropriately licensed and skilled personnel prior to any renovation or demolition of the premises.
This HMSMP includes the following:
a register of all identified hazardous materials
extent, form, condition and risks associated with nominated hazardous materials
labelling requirements for identified hazardous materials
a timetable for managing risks including priorities for removal or control of ACM and for reviewing risk assessments
responsibilities of all persons involved in hazardous materials management
procedures to address incidents or spillage involving ACM
safe work and removal methods
guidelines on reviewing and updating the HMSMP and hazardous materials register
3.1 Requirements for the HMSMP
This HMSMP must be held on site for ready access. All personnel undertaking any repair or maintenance work must be provided with a copy of the HMSMP before commencement of work.
Maintenance, trade and other personnel must be instructed not to remove or damage identified hazardous materials if hazardous material is identified in the area where work will be undertaken it must be removed or remediated before work begins.
Removal of hazardous material must be undertaken by suitably qualified persons in accordance with relevant Regulations and Codes of Practice.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 19 of 94
3.2 Exclusions
The HMSMP commissioned by the client was to be non-destructive and non-intrusive in nature. This type of commission limits or restricts access to the building structure, some surfaces and materials.
This report outlines only the hazardous material categories specified. Other hazards are present in this building including but not limited to ionising radiation and high intensity electromagnetic laser radiation. This document must NOT be treated as a comprehensive list of all hazards present. Please contact ANU representatives for further details.
The survey undertaken was limited to those areas available for access at the time of building inspection. Only the areas accessible to the surveyors at the time of the building inspection are included in this HMSMP.
Unless specifically noted, the survey did not cover exterior ground surfaces and sub-surfaces (e.g. infill/soil) or materials other than normal building fabric such as materials in laboratories or special purpose facilities.
At the time of survey no access was gained to materials and / or void areas located behind, above, or attached to any sampled or assumed hazardous materials.
The HMSMP does not include the areas, locations and equipment items to which the surveyors could not gain access at the time of inspection.
Some other areas which may conceal asbestos include:
Material Location
Asbestos millboard lining Air conditioning duct work adjacent to heater elements
Asbestos insulation and gaskets/joints Within mechanical equipment concealed by outer metal cladding
Asbestos insulation Walls and cavities (e.g. as lagging to hot water pipes set into and sealed within masonry walls)
Vinyl floor tiles and floor covering Beneath carpets
Sheeting Backing material to ceramic tiles and as packers to building construction joints
Asbestos cement sheet formwork and electrical cable/water pipe duct Sub-ground floor slab
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 20 of 94
No absolute determination can be made regarding the possibility of concealed or inaccessible hazardous materials or items in the areas, locations and equipment listed in the table above until access is gained to allow for inspection.
Materials and equipment in any non-accessed area should therefore be assumed to contain ACM, SMF, lead paint, PCB, ODS and A/UST (the nominated hazardous materials) and be treated appropriately until assessment and sample analysis confirm otherwise.
Samples were not taken where the act of sampling would endanger the surveyor or affect the structural integrity of the item concerned.
This HMSMP, although extensive, is not intended for and must not be used as a specification or method statement for any future hazardous material removal project. In this instance detailed plans, quantities etc. would be required.
Before any refurbishment or hazardous material removal projects, the contractor(s) carrying out the work must fully acquaint themselves with the extent of the hazardous materials, particularly in those areas which may need full or partial demolition in order to determine the exact extent and location of such materials.
Care should be taken when demolishing or excavating to determine the existence or otherwise of hazardous materials. For example subsurface pipes and drains, revealed through excavation may be constructed of asbestos cement. Wherever a material is uncovered or revealed and it is suspected to be hazardous, it should be assumed to be hazardous and treated appropriately until such time as assessment and sample analysis of the material confirms otherwise.
Until this confirmation occurs the building work must cease in the immediate vicinity of the suspect material and a suitably qualified person must issue a clearance certificate or report before the building work can recommence in the affected area.
To ensure contextual integrity, this HMSMP must always be read in its entirety and should never be referred to in part only.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 21 of 94
3.3 Limitations
This report is based on the information obtained by Robson Environmental Pty Ltd at the time of inspection. Robson Environmental Pty Ltd will not update this report; nor take into account any event(s) occurring after the time that its assessment was conducted.
As both the range and use of manufactured products containing hazardous materials was extremely widespread, Robson Environmental Pty Ltd cannot accept responsibility for any consequential loss or damage that results from non-recognition of a material that may later be established to contain hazardous material. For example, certain textured wall and ceiling finishes may contain small traces of asbestos fibre. In situ, textured finishes are often composed of assorted batches of product, or may have been repaired/patched at various times. It is therefore always a possibility that the samples collected may not always be representative of the entire material.
While Robson Environmental Pty Ltd has taken all care and attention to ensure that this report includes the most accurate information available, it has been unable to examine any inaccessible materials or materials hidden from view.
Under normal construction practices some materials are “built in” or “randomly applied”. These materials are therefore not readily accessible and can only be exposed through demolition or damage to the structure or finishes. Access to a material may also be prevented or restricted by “in service” or operational equipment, or where to obtain access contravenes a relevant statutory requirement or code of practice. (e.g. electrical switchboards) Consequently, while all reasonable care and attention was taken in compiling this report no guarantee to its completeness can be given.
Robson Environmental Pty Ltd has taken all care to ensure that this report includes the most accurate information available, where it uses test results prepared by other persons it relies on the accuracy of the test results in preparing this report. In providing this report Robson Environmental Pty Ltd does not warrant the accuracy of such third party test results.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 22 of 94
4 ASBESTOS SURVEY RESULTS
4.1 Survey Details
The survey of the site included all accessible areas of the building(s) except where stated otherwise. For further asbestos management information, refer to Appendix D.
4.2 Survey Methodology
The survey involved a visual inspection of the premises and a condition assessment of identified ACM. Samples were analysed in Robson Environmental's National Association of Testing Authorities (NATA) laboratory using polarising light microscopy (PLM) and dispersion staining. Samples were a representative selection of materials suspected of containing asbestos. Samples were not taken from all areas due to the uniformity of the materials used throughout the building. Laboratory analysis certificates are presented in Appendix A.
4.3 Sample Analysis
Table 2: Mineralogical Analysis of Samples for Asbestos using PLM
Building 38 - Physics Building
Sample reference Sample location Sample
type Composition Asbestos type
A2626 L1 Store G.30C - infill panel above door Sheet No Asbestos Detected
A2627 L1 Store G.30B - infill panel above grated window and ceiling Sheet No Asbestos Detected
A2628 L1 Store G.30 - wall Sheet Chrysotile Asbestos Detected
A2629 L1 access to subfloor G.02C - green floor tiles
Vinyl floor tile No Asbestos Detected
A2630 L2 ceiling space - joints to HVAC ductwork Mastic Chrysotile Asbestos
Detected
A2631 L2 Office 1.60 - green hessian backed floor tiles
Vinyl floor tile No Asbestos Detected
A2632 L1 Lift 1.01E - grey flecked floor tiles
Vinyl floor tile No Asbestos Detected
A2633 LB Radioactive Store B.04 - cap to furnace device
Cement sheet
Amosite, Chrysotile Asbestos Detected
A2634 LB area adjacent access point and air compressor - to surfaces
Pipe lagging debris
Amosite Asbestos Detected
A2636 Exterior - sprayed coating to column Sprayed coating No Asbestos Detected
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 23 of 94
Building 38 - Physics Building
Sample reference Sample location Sample
type Composition Asbestos type
A2637 LB Lift Motor Room B.04 - switchboard backing Sheet No Asbestos Detected
A2638 L1 Lift - door seal Rope seal Chrysotile Asbestos Detected
A2639 L1 Plant Room G10 - sprayed coating to ceiling pipes
Sprayed coating No Asbestos Detected
A2640 LB tunnel to Building 39 - to pipes Pipe lagging debris
Amosite Asbestos Detected
A2641 Exterior bridge to Building 38b - fascia panels to inside and outside Sheet No Asbestos Detected
NATA accredited laboratory:
Robson Environmental Pty Ltd Accreditation number: 3181
Chrysotile = white asbestos Amosite = grey or brown asbestos Crocidolite = blue asbestos
It should be noted that the above samples were a representative selection of materials suspected of containing asbestos.
On-site inspections and an examination of the Asbestos Register within this report should be undertaken prior to the commencement of any asbestos removal programme.
4.4 Risk Assessment
The purpose of the risk assessment is to enable informed decisions to be made concerning the control of ACM.
The risk assessment should take account of the identification information in the Asbestos Register, including: type of ACM (non-friable or friable)
condition and location of ACM
whether the ACM is likely to be disturbed due to its condition and location
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 24 of 94
the likelihood of exposure
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 25 of 94
Types of ACM
Non-friable ACM
Non-friable ACM is any material that contains asbestos bound into a stable matrix. It may consist of cement or various resins/binders and cannot be reduced to a dust by hand pressure. As such it does not present an exposure hazard unless cut, abraded, sanded or otherwise disturbed. Therefore, the exposure risk from non-friable ACM is negligible during normal building occupation. Note: If non-friable ACM is damaged or otherwise deteriorated, the risk assessment may be reviewed to reflect a higher potential for exposure to asbestos fibres. A licensed Asbestos Assessor should perform the risk assessment.
Friable ACM Friable ACM can be crumbled or reduced to a dust by hand pressure when dry and can represent a significant exposure hazard. Examples of friable asbestos are hot water pipe lagging, severely damaged asbestos cement sheet, limpet spray to structural beams and electrical duct heater millboard.
ACM CONDITION RATING
1 Severe Deteriorated surface in extremely poor condition
2 Poor Deteriorated material
3 Normal Stable asbestos with little damage
4 Good Well sealed stable surfaces in accessible locations
ACM RISK RATING
A Very High Exposure to airborne asbestos as a consequence of extremely minor disturbance
B High Exposure to airborne asbestos likely as a consequence of significant disturbance
C Medium Exposure to airborne asbestos unlikely during normal building use
D Low No exposure to airborne asbestos during normal building use
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 26 of 94
4.5 Asbestos Register
The Asbestos Register details the type, location, risk assessment and action required for all identified ACM. The Register should be accessed to inform all decisions made concerning control of ACM. Action taken to control ACM must be recorded in this Register in order to comply with current legislation. Table 3A: Asbestos Register
Building 38 - Physics Building
Sample No. Material Description & Location Condition
Rating Risk
Rating Approx
Quantity Recommended Management
Action Action
Undertaken Assessor/ Date
assessed
VA1
Double brick wet areas - Pipe lagging (fibrous) - To hot water pipes embedded in walls (throughout building) (Presumed Friable)
3 B - Further investigation required prior to possible disturbance
A2628 L1 Store G.30 - Sheet - wall (Non-Friable)
3 D 21 m²
Label and maintain Inspect every 5 years
Encapsulate Remove prior to demolition or
refurbishment
A2630 L2 ceiling space - Mastic - joints to HVAC ductwork (Non-Friable)
4 D -
Label and maintain Inspect every 5 years
Remove prior to demolition or refurbishment
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 27 of 94
Building 38 - Physics Building
Sample No. Material Description & Location Condition
Rating Risk
Rating Approx
Quantity Recommended Management
Action Action
Undertaken Assessor/ Date
assessed
Refer to A2630
L1 Plant Room G.16A - Mastic - joints to HVAC ductwork (Non-Friable)
4 D -
Label and maintain Inspect every 5 years
Remove prior to demolition or refurbishment
A2633
LB Radioactive Store B.04 - Cement sheet - cap to furnace device (Non-Friable)
4 D 2 no Remove
A2634
LB area adjacent access point and air compressor - Pipe lagging debris - to surfaces (Friable)
2 B - Remove
Prohibit access
A2638 L1 Lift - door seal (Friable)
3 B 3 lin m
Label and maintain Inspect annually
Remove prior to demolition or refurbishment
A2640 LB tunnel to Building 39 - Pipe lagging debris - to pipes (Friable)
2 B - Remove
Prohibit access
Refer to Section 2.4 Table 1B for presumed ACM and Section 3.2 for exclusions
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 28 of 94
Table 3B: Register of sampled materials which have been confirmed as non ACM
Building 38 - Physics Building Sample number Type Locations
A2626 Sheet L1 Store G.30C - infill panel above door
A2627 Sheet L1 Store G.30B - infill panel above grated window and ceiling
A2629 Vinyl floor tile L1 access to subfloor G.02C - green floor tiles
A2631 Vinyl floor tile L2 Office 1.60 - green hessian backed floor tiles
A2632 Vinyl floor tile L1 Lift 1.01E - grey flecked floor tiles
A2636 Sprayed coating Exterior - sprayed coating to column
A2637 Sheet LB Lift Motor Room B.04 - switchboard backing
A2639 Sprayed coating L1 Plant Room G10 - sprayed coating to ceiling pipes
A2641 Sheet Exterior bridge to Building 38b - fascia panels to inside and outside
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 29 of 94
5 LEAD PAINT SURVEY RESULTS
5.1 Introduction
Lead paint is defined by the Australian Standard (AS 4361.2 – 2017 Guide to hazardous paint management Part 2: Lead paint in residential, public and commercial buildings) as a paint or component coat of a paint system containing lead or lead compounds, in which the lead content (calculated as lead metal) is in excess of 0.1% by weight of the dry film as determined by laboratory testing.
Analytical values of ≤ 0.1% Pb allow the sample to be categorised as being lead free paint.
5.2 Results
Paint was tested during the hazardous materials survey using 3M™ LeadCheck™ Swabs which have a detection limit of 0.06% w/w lead, sufficient to classify paint as lead free under AS4361.2-2017. Where requested by the client, deemed prudent by the assessor, or required due to inconclusive results from this test, representative paint samples were also collected in accordance with AS4361.2-2017 and analysed for lead content. In general however as the detection limit of 0.06% w/w lead is only slightly lower than the threshold for lead paint of 0.10% lead set out in AS4361.2-2017 it is generally satisfactory to treat a positive result with 3M™ LeadCheck™ Swabs as being indicative of lead paint, obviating the need for further sampling and analysis.
The sampling criterion provided below is taken from AS4361.2-2017 Section A4 Sampling Strategy clauses (a, b, c);
(a) An adequate number of sample sites should be analysed to properly characterise the paint systems present on site.
(b) For small surfaces such as architraves, windows and doors and cupboards, a single sample may suffice.
(c) For large, uniformly painted surface areas such as the exterior facade of high rise buildings, or for interior walls and ceilings of large rooms, and where laboratory testing is employed, composite samples should be taken from three separate locations in 10m² sections.
Collected paint samples were analysed for their lead (Pb) content by Envirolab Services Pty Ltd – NATA accreditation number: 2901 using ICP/AES techniques and in-house Method No.4.
Within the same building, wherever a paint coating had a similar surface texture, colour, etc. to a paint coating that had already been sampled because of its suspected lead content, it was presumed that these paint coatings were identical. However, results can only be guaranteed valid for directly tested/sampled paints (especially due to deliberate attempts to match new paint to existing coatings in some applications).
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 30 of 94
Table 4: Lead Composition in Paint by Inductively-Coupled Plasma Spectroscopy
Building 38 - Physics Building
Sample No. Item No. Sample location Colour Lead in Paint %
A2635 PB1294 Exterior loading dock - fire extinguisher case Orange 0.83
Notes: Lead Paint (> 0.1% Pb) Lead-free Paint (≤ 0.1% Pb)
5.3 Discussion and Conclusion
The analytical result(s) of paint sampling revealed that the orange paint to the fire extinguisher case in the loading dock is lead paint.
It is recommended that lead paint be maintained. Any areas that begin to flake, peel or otherwise deteriorate should be appropriately remediated. If the paint is to be removed this should be undertaken by a suitably qualified person.
It should be assumed that all similar paint(s) throughout the premises contains comparable percentages of lead.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 31 of 94
6 Synthetic Mineral Fibre (SMF) Survey Results
6.1 Introduction
SMF is a generic term used to collectively describe a number of amorphous (non-crystalline) fibrous materials including glass fibre, mineral wool (Rockwool and Slagwool) and ceramic fibre. Generally referred to as SMF, these materials are also known as ‘Man-Made Mineral Fibres’ (MMMF).
SMF products are used extensively in commercial and residential buildings for thermal and acoustic insulation, and as a reinforcing agent in cement, plaster and plastic materials. In some specialised instances, SMF materials have also been used as alternatives to asbestos, especially where high temperature insulation properties are required.
There are two basic forms of SMF insulation bonded and unbonded.
The bonded form is where adhesives, binding agents, facing/cladding, cement or other sealants have been applied to the SMF before delivery and the SMF product has a specific shape (e.g. a binding or sealing agents hold the SMF in a batt or blanket form). Some bonded SMF materials may also be clad in various coverings on one or more sides (e.g. a silver foil backing).
The unbonded form has no adhesives, binding agents, facing/cladding or sealants applied, and the SMF is a loose material (e.g. wet spray and loose fill).
6.2 Results
Table 5: Visual Assessment of Samples
Building 38 - Physics Building
Item No Location Sample Type Form
SMF1182 Ceilings throughout Suspended ceiling tiles Bonded
SMF1176 L1 Plant Room G.16A Insulation to pipe work Bonded
SMF1165 L1 Store G.30 Seal to door of flammable liquids cupboard Bonded
SMF1168 L1 Plant Room G.10 Rheem electric hot water unit Bonded
SMF1169 L2 riser cupboard 1.01A Insulation to pipe work Bonded
SMF1172 L2 ceiling space Loose insulation Bonded
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 32 of 94
Building 38 - Physics Building
Item No Location Sample Type Form
SMF1173 L2 riser cupboard 1.01J Insulation to pipe work Bonded
SMF1177 L2 riser cupboard 1.80A Insulation to pipe work Bonded
SMF1184 L2 riser cupboard 1.01G Insulation to pipe work Bonded
SMF1178 L2 Plant Room G.16A Insulation to ductwork Bonded
SMF1179 L2 ceiling space Insulation to pipe work Bonded
SMF1180 L2 riser cupboard 1.01I Insulation to pipe work Bonded
SMF1181 L2 ceiling space Insulation to ductwork Bonded
SMF1183 L2 ceiling space Sisalation Bonded
SMF1175 L2 riser cupboard 1.01D Insulation to pipe work Bonded
SMF1162 LB B.01 Insulation debris Bonded
SMF1166 LB B.01 To pipes Bonded
6.3 Conclusion
It should be presumed that SMF materials may be present to inaccessible areas including the ceiling space of areas which are inaccessible. If building work is likely to significantly disturb the insulation, the SMF materials should be removed using effective dust control procedures.
Refer to Appendix D for safe SMF handling.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 33 of 94
7 POLYCHLORINATED BIPHENYLS (PCB) SURVEY RESULTS
7.1 Introduction
PCB is the common name for polychlorinated biphenyls. PCBs range in appearance from colourless, oily liquids to more viscous and increasingly darker liquids, to yellow then black resins, depending on the chlorine content of the PCB.
PCBs are chemically stable synthetic compounds that do not degrade appreciably over time or with exposure to high temperatures. The major use of PCBs was as an insulating fluid inside transformers and capacitors. Capacitors containing PCBs were installed in various types of equipment including domestic appliances, motors and fluorescent light fittings during the 1950s, 60s and 70s.
These applications generally do not present an immediate risk to human health or the environment as the equipment is sealed and contains relatively small amounts of PCB. The equipment can continue to be used safely provided that the capacitors do not leak.
The Australian and New Zealand Environment and Conservation Council (ANZECC) in its PCB Management Plan of 2003 stipulate cessation dates for the generation of PCB scheduled waste, the use of articles containing PCB scheduled waste, and the disposal of PCB scheduled waste*.
* PCB scheduled waste means any PCB material that has no further use that contains PCBs at levels at, or in excess of 50mg/kg and is of a quantity of 50g or more.
Small equipment items and capacitors found in households and commercial buildings that contain scheduled PCBs (i.e. at or in excess of 50mg/kg) are to be disposed of as scheduled PCB waste. Where the aggregate weight of the items or capacitors exceeds 10kg, they must be notified to the relevant Commonwealth, State or Territory Government agency prior to their disposal.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 34 of 94
7.2 Results
Table 6: PCB and non PCB Containing Capacitors Identified on fluorescent light fittings
Item No. Location Make - Type Capacitance (μF)
Light fittings visually assessed as being new. Prior to any works that may affect fluorescent light fittings full access should be provided by a licensed electrician to determine if PCBs are present.
Item No. Location Make - Type Capacitance (μF)
No Non-PCB capacitors were located
* Note that light fittings were only inspected where they were isolated by a qualified electrician. Live light fittings were not inspected, and accordingly no determination about whether or not they contain PCB is included in this report.
For further PCB management information refer to Appendix D.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 35 of 94
8 OZONE DEPLETING SUBSTANCES SURVEY RESULTS
The site was surveyed for the presence of air conditioning and refrigeration units that contain ozone depleting substances.
ODS are used for heat transfer in refrigeration and air conditioning systems, absorbing or releasing heat according to vapour pressure. Release of these substances to the atmosphere has the ability to cause long term atmospheric pollution that can lead to ozone depletion, global warming, petrochemical smog and acid rain.
The ozone depletion potential (ODP) of a fluorocarbon refrigerant gas, its global warming potential (GWP) and estimated atmospheric life (EAL) all contribute to its potential to deplete the stratospheric ozone layer and enhance the greenhouse effect leading to global warming.
Chlorofluorocarbons (CFCs) contain chlorine and possess a large ODP, high GWP and long EAL. They are generally found in refrigeration and air-conditioning systems e.g. centrifugal chillers.
Hydrochlorofluorocarbons (HCFCs) are less saturated with chlorine than are CFCs and the hydrogen within these compounds give the HCFCs a much shorter EAL and lower ODP. They are generally found in refrigeration systems that are used for food display, cold stores and self contained, split, multi-split and central plant chillers used for building air-conditioning.
Hydrofluorocarbons (HFCs) are a class of replacement gases for CFCs. They do not contain chlorine or bromine and therefore do not deplete the ozone layer. While all HFCs have an ODP of zero, some do have a high GWP (e.g. R-404A, R-407B, R-125 etc).
Halons are synthetic chemical compounds that contain one or two carbon atoms, bromine and other halogens. They have a long atmospheric lifetime and cause very aggressive ozone depletion when breaking down in the stratosphere. Halons were introduced into Australia as fire-extinguishing agents in the early 1970s and quickly replaced many previously accepted fire-fighting products because of their superior fire-extinguishing characteristics and ease of use.
Halon 1211 was commonly used in portable fire extinguishers, while fixed fire protection systems, such as those that protect computer rooms and ship engine rooms, commonly contained Halon 1301.
Halon 1301 has an ODP that is 10 times greater that of CFCs, while Halon 1211 has an ODP 3 times greater than that of CFCs.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 36 of 94
8.1 Results
Table 7: Chemical properties of ODS located during survey
Building 38 - Physics Building
ODS Item No Location R Number Chemical
name ODP GWP EAL
ODS731 Exterior - APAC heat pump R-22 CFCIF2 0.055 1700 13.3
ODS724 Exterior - Daikin R-22 CFCIF2 0.055 1700 13.3
ODS733 Exterior - Carrier Presumed R-22 CFCIF2 0.055 1700 13.3
ODS728 L1 Plant Room G.10 - APAC heat pump R-22 CFCIF2 0.055 1700 13.3
Chemical properties of non ODS located during survey
Building 38 - Physics Building
Non ODS Location R Number Chemical name ODP GWP EAL
ODS730 Exterior - Daikin Inverter R-32 CH2F2 0 675 4.9
ODS729 Exterior - Daikin Super Inverter R-410A HFC-32 (50%), HFC-
125 (50%) 0 1370 36
ODS725 Exterior - Mitsubishi Inverter R-410A HFC-32 (50%), HFC-
125 (50%) 0 1370 36
For further refrigerant management information refer to Appendix D.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 37 of 94
9 FUEL STORAGE FACILITIES
It is important to note that prior to the introduction of natural gas in the ACT in the 1980s commercial premises generally utilised heating systems where boilers were fuelled by diesel or heating oils which were stored in A/USTs.
9.1 Results
A/UST Type
Item No Location Recommendations
No storage tanks located
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 38 of 94
10 ASBESTOS MANAGEMENT
10.1 Management of ACM
General requirements
ACM identified as representing an exposure risk (see Table 3A Asbestos Register) should be removed or otherwise controlled.
Any ACM that is not scheduled for immediate removal should be labelled with appropriate warnings and maintained in good condition.
The location of ACM must be entered into the Asbestos Register.
Maintenance and other personnel must be made aware of the location of ACM.
The Asbestos Register must be freely available.
Unless they have valid ACT Asbestos Removal licence, maintenance workers, trades or occupants shall not remove or knowingly damage identified ACM.
Before any planned demolition, refurbishment or maintenance, its effect upon any in situ asbestos must be established by reference to this document, including amendments.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 39 of 94
10.2 Management of Contractors
Before any contractor is engaged to carry out work on a site, the Asbestos Register, site plan and photographs should be checked to ensure the work will not interfere with, or disturb asbestos containing materials (ACM).
The chart below should be used by the PMCW to induct contractors onto sites:
Contractor arrives on site Check Safe Work Method Statement (SWMS) and Trade Licenses (including Asbestos Awareness training) of all
personnel involved in the work
Induct contractor Conduct contractor’s induction for the personnel involved in the work and ensure they are aware of any special requirements for ACM, security, no smoking, etc.
Check the Asbestos Register
The Asbestos Register and plan should be readily accessible (i.e. front office/reception) and in colour. Check the Asbestos Register with the contractor for ACM in the proposed work area.
Is asbestos present in the work area?
No Yes
Contractor may proceed with work
Will the asbestos be disturbed?
No Yes
Contractor may proceed with work
No work to be conducted – contact the PMCW immediately informing them of the problem.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 40 of 94
10.3 Asbestos Emergency Procedures
The following course of action should be taken immediately if ACM or suspected ACM is disturbed, or is accidentally damaged.
Evacuate all personnel from the immediate area and if present shut down the air-conditioning system
Restrict access to the area by locking or cordoning off the area until a full assessment has been completed
Report the incident to the PMCW and supply the exact location & short brief of what has occurred
PMCW immediately inform stakeholders of the incident
PMCW to engage a Licensed Asbestos Assessor to conduct a site assessment, take samples, conduct air monitoring (if required) and provide written report containing a risk
assessment
PMCW receives advice from Licensed Asbestos Assessor on outcome of site assessment
No asbestos present Asbestos present
Advise all stakeholders of the outcome Make safe using recommendations of the Licensed Asbestos Assessor
Resume normal operations Management Action & Remediation Plan and Asbestos Register updated
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 41 of 94
10.4 PMCW Decision Record
Option 1: Defer action
Item no. ACM and Location Reason Authorisation Date
Option 2: Encapsulate or seal
Item no. ACM and Location Reason Authorisation Date
Option 3: Removal
Item no. ACM and Location Reason Authorisation Date
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 42 of 94
10.5 Timetable for Action
The timetable for action should be administered to ensure the PMCW has a clear plan for all works which may affect ACM in the workplace. This includes maintenance work, scheduled removal work and risk assessment reviews, which may impact ACM. Table 8: Timetable for action
ACM removal/ work Date of scheduled works Details Authorisation Date
Asbestos review/audit
Date of scheduled review Details Authorisation Date
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 43 of 94
11 RESPONSIBILITIES
11.1 Asbestos - Provision of Information
The PMCW must:
ensure the ACM register and all relevant information pertaining to asbestos in the workplace is freely available upon request
provide occupants with up-to-date information relating to the condition and relative risk of ACM in the workplace
provide information on the control measures in place to contain ACM-related risk and
provide information to staff and contractors on measures to be taken to ensure that they are not exposed to asbestos in the workplace, either through accident or negligence
PMCW Action Record
Record all communication activities undertaken to inform staff/occupants of ACM in the workplace.
Action Authorisation Date
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 44 of 94
11.2 Updating the Risk Assessment
The register of ACM, including any risk assessments, should be reviewed every 12 months or earlier where:
a risk assessment indicates the need for reassessment; or
any ACM has been disturbed or moved
A visual inspection of identified ACM should be undertaken as part of any review.
Each review should critically assess all asbestos management procedures and their effectiveness in: preventing exposure to asbestos fibres
controlling access to asbestos
highlighting the need for action to maintain or remove ACM
maintaining the accuracy of the ASMP
Details of any mitigating actions must be recorded in the Asbestos Register (refer Table 3A).
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 45 of 94
11.3 Key Personnel
This section outlines the responsibilities of all persons involved in the safe management of ACM. 1. PMCW Name:
Contact details:
Responsibilities:
e.g. provision of information
2. Occupational Health and Safety Representative Name:
Contact details:
Responsibilities:
e.g. keeping occupants informed of any changes to the status of ACM in the workplace
3. Facilities Management (if applicable) Name:
Contact details:
Responsibilities:
e.g. arrange removal and repair works as required; maintaining the HMSMP
4. Other Name:
Contact details:
Responsibilities:
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 46 of 94
12 ASBESTOS REMOVAL WORKS
12.1 PMCW Responsibilities
Where it has been determined that ACM is to be removed, the PMCW must ensure that a risk assessment is performed before the removal work commences and that the removalist takes this risk assessment into account. The risk assessment must include the possibility of uncovering previously concealed ACM, and that concealed ACM is subsequently identified by a licensed Asbestos Assessor.
The PMCW should provide a detailed scope of works prepared by a licensed Asbestos Assessor for the removalist, including potential hazards, details on areas, which contain asbestos and arrangements for clearance inspections and airborne fibre monitoring.
12.2 Removalist Responsibilities
Before the commencement of removal work, the licensed removal contractor must:
Provide a site-specific Asbestos Removal Control Plan(ARCP)
Ensure the removal is adequately supervised and carried out in a safe manner
Ensure that the equipment used in the project is appropriate for the task
Ensure all persons carrying out the removal are competent and trained for the type of work being carried out
Demonstrate that they have a health surveillance program in accordance with the requirements of Code Of Practice: How To Safely Remove Asbestos
12.3 Licensing Requirements
All Asbestos Removalists in the ACT are licensed by WorkSafe ACT
As a minimum the holder of an ACT Asbestos Removal Licence is required to demonstrate practical experience in the industry for at least three years and possess a full and complete understanding of the requirements of: How to Manage and Control Asbestos in the Workplace Code of Practice
How to Safely Remove Asbestos Code of Practice
Work Health and Safety Act 2011
Work Health and Safety Regulations 2011
Environment and Planning Directorate (EPD) specify requirements for authorising certifiers and WorkSafe ACT and ACT NOWaste for the removal and transport of ACM.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 47 of 94
12.4 Approval to Begin Asbestos Removal Works
All removal methods and procedures are required to be undertaken in accordance
with current legislation.
The PMCW in conjunction with a licensed Asbestos Assessor where required, will inform the asbestos removalist of the ‘Scope of Works’.
The licensed Asbestos Assessor will be required to provide a clearance certificate on satisfactory completion of the works.
12.5 Emergency Work in Areas Containing Asbestos
If emergency access is required contact the PMCW.
If the PMCW determines that asbestos is likely to be disturbed, all works must be undertaken in accordance with current legislation - that is, a licensed Asbestos Removalist must be contracted to undertake any asbestos removal works.
A licensed Asbestos Assessor will be required to provide a clearance certificate on satisfactory completion of the works.
12.6 Monitoring Arrangements
Control air monitoring should be performed when indicated by a Risk Assessment to ensure the control measures are effective.
All air monitoring must be performed by a licensed Asbestos Assessor accredited to perform air sampling for asbestos. Sampling should be performed in accordance with the Guidance Note on the Membrane Filter Method for Estimating Airborne Asbestos Fibres [NOHSC: 3003 (2005)].
It is the Asbestos Removalist’s responsibility to ensure that the maximum fibre levels throughout asbestos removal and associated works does not equal or exceed the minimum practical detection limit of 0.01 fibres per millilitre of air (F/ml). If the airborne fibre levels are observed at or exceeding those specified below, the licensed Asbestos Assessor will instruct the contractor to take the appropriate control /action as per current legislation.
Table 9: Control levels and required actions
Control Level (airborne asbestos fibres/ml) Control/Action
< 0.01 Continue with control measures
0.01 Review control measures
0.02 Stop removal work and find the cause
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 48 of 94
12.7 Clearance Inspections
Following removal work, a licensed Asbestos Assessor must undertake a clearance inspection before re-occupation of an asbestos work area.
All barriers and warning signs should remain in place until the area has been cleared.
12.8 ACM removal/maintenance record
The Asbestos Register, Section 4.5, Table 3A is to be completed by the PMCW after receiving appropriate clearance certification from a licensed Asbestos Assessor.
The ‘Work Performed’ and ‘Asbestos Control Measure’ Tables are required to be completed by the PMCW.
1. Work Performed
Company name Contact details Date of work + job no. Scope of work
2. Asbestos Control Measures
Work performed Air monitoring/ decontamination
Clearance certificate issued Other
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 49 of 94
3. Additional Information
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 50 of 94
13 FURTHER INFORMATION
13.1 Useful Contacts
Additional information on asbestos can be obtained from the following organisations and agencies.
Environment and Planning Directorate (EPD)
Dame Pattie Menzies House 16 Challis Street Dickson ACT 2602 Phone: 02 6207 1923 Internet: www.environment.act.gov.au
ACT Government Phone: 13 22 81
Internet: www.asbestos.act.gov.au WorkSafe ACT 255 Canberra Avenue
Fyshwick ACT 2609 Phone: 02 6205 0200 Email: [email protected] Internet: www.WorkSafe.act.gov.au
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 51 of 94
14 APPENDICES
14.1 APPENDIX A – Laboratory Reports
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 52 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 53 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 54 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 55 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 56 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 57 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 58 of 94
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 59 of 94
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 60 of 94
14.2 APPENDIX B – Plans
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 61 of 94
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 62 of 94
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 63 of 94
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 64 of 94
14.3 APPENDIX C – HAZMAT Item locations & representative photographs
ASBESTOS - Building 38 - Physics Building
SAMPLE NO LOCATION MATERIAL
DESCRIPTION PHOTOGRAPH
VA1 Double brick wet areas - Pipe lagging (fibrous) - To hot water pipes embedded in walls (throughout building) (Presumed Friable)
Pipe lagging (fibrous) (Presumed Friable)
A2628 L1 Store G.30 - wall Sheet
(Non-Friable)
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 65 of 94
ASBESTOS - Building 38 - Physics Building SAMPLE
NO LOCATION MATERIAL DESCRIPTION PHOTOGRAPH
A2630 L2 ceiling space - joints to HVAC ductwork
Mastic (Non-Friable)
Refer to A2630
L1 Plant Room G.16A - joints to HVAC ductwork
Mastic (Non-Friable)
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 66 of 94
ASBESTOS - Building 38 - Physics Building SAMPLE
NO LOCATION MATERIAL DESCRIPTION PHOTOGRAPH
A2633 LB Radioactive Store B.04 - cap to furnace device
Cement sheet (Non-Friable)
A2634 LB area adjacent
access point and air compressor - to surfaces
Pipe lagging debris (Friable)
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 67 of 94
ASBESTOS - Building 38 - Physics Building SAMPLE
NO LOCATION MATERIAL DESCRIPTION PHOTOGRAPH
A2638 L1 Lift - door seal Rope seal (Friable)
A2640 LB tunnel to Building
39 - to pipes Pipe lagging debris (Friable)
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 68 of 94
LEAD PAINT - Building 38 - Physics Building
ITEM NO LOCATION Lead % PHOTOGRAPH PB1294 Exterior loading dock
- fire extinguisher case
0.83
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 69 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1182 Ceilings throughout
Suspended ceiling tiles
SMF1176 L1 Plant Room
G.16A Insulation to pipe work
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 70 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1165 L1 Store G.30 Seal to door of flammable liquids cupboard
SMF1168 L1 Plant Room
G.10 Rheem electric hot water unit
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 71 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1169 L2 riser cupboard 1.01A
Insulation to pipe work
SMF1172 L2 ceiling
space Loose insulation
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 72 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1173 L2 riser cupboard 1.01J
Insulation to pipe work
SMF1177 L2 riser
cupboard 1.80A
Insulation to pipe work
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 73 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1184 L2 riser cupboard 1.01G
Insulation to pipe work
SMF1178 L2 Plant Room
G.16A Insulation to ductwork
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 74 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1179 L2 ceiling space
Insulation to pipe work
SMF1180 L2 riser
cupboard 1.01I Insulation to pipe work
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 75 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1181 L2 ceiling space
Insulation to ductwork
SMF1183 L2 ceiling
space Sisalation
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 76 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1175 L2 riser cupboard 1.01D
Insulation to pipe work
SMF1162 LB B.01 Insulation debris
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 77 of 94
SMF - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
SMF1166 LB B.01 To pipes
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 78 of 94
OZONE DEPLETING SUBSTANCES - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
ODS731 Exterior, APAC heat pump
APAC heat pump
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 79 of 94
OZONE DEPLETING SUBSTANCES - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
ODS724 Exterior, Daikin Daikin
ODS733 Exterior, Carrier Carrier
(Presumed ODS)
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 80 of 94
OZONE DEPLETING SUBSTANCES - Building 38 - Physics Building
ITEM NO LOCATION MATERIAL TYPE PHOTOGRAPH
ODS728 L1 Plant Room G.10, APAC heat pump
APAC heat pump
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 81 of 94
14.4 APPENDIX D – Hazardous Material Management Information
ASBESTOS
Some 3000 products have been manufactured using asbestos, of which cement sheeting, pipe insulation, textiles, gaskets, vinyl floor tiles and fire door cores are the most commonly encountered. The mineral asbestos (i.e. Crocidolite, Chrysotile and Amosite and other forms) is classified by the National Occupational Health and Safety Commission as a Category 1 carcinogen. If respirable asbestos fibres are inhaled they may cause an inflammatory response, which in turn may lead to asbestosis (scarring of the lung), mesothelioma (cancer of the pleura or peritoneum) or lung cancer.
It is illegal under Commonwealth, State and Territory legislation to manufacture asbestos building materials or to reuse asbestos products.
Asbestos sheeting or ‘fibro’ is bonded into a stable matrix and as such does not present an exposure hazard unless it is cut, abraded, sanded or otherwise disturbed. This material is referred to as non friable ACM. Friable ACM has the potential to release fibre with only minor disturbance.
The health risks associated with asbestos exposure increase with the fibre type, level and frequency of exposure. Crocidolite (blue asbestos) is the most hazardous type. Amosite (brown asbestos) is not as hazardous as crocidolite but is significantly more hazardous than chrysotile (white asbestos). Exposure to all types of asbestos can result in diseases including asbestosis, lung cancer and mesothelioma. Smoking increases the risk of disease 50 fold. The often heard adage ‘ one fibre can kill you” is overly simplistic. Evidence indicates that risk increases with the level, type and frequency of exposure. Some individuals may be predisposed to disease at low and infrequent exposure, while others suffer no ill effect even after prolonged industrial exposure. We do not know what level can be considered safe nor what level may be considered hazardous. Asbestos may also be naturally present in the environment at very low levels. Therefore controls should be implemented to avoid exposure as far as practicable.
Asbestos is only hazardous if it becomes airborne and inhaled. When it is fully encapsulated within the structure it cannot become airborne. Simple engineering controls can ensure it remains encapsulated. These controls are detailed in the Required Actions and Recommendations detailed in this report.
Provided the site has been inspected by a licensed Asbestos Assessor and their recommendations adopted, normal occupation would not be hazardous. It is vital that any maintenance or renovation be in strict accordance with the Assessor’s recommendations.
Any person employed to undertaken any maintenance or refurbishment must be informed of the presence of friable and/or non friable asbestos in the premises. The PMCW must ensure that if planned work may impact on any asbestos materials, the asbestos is removed or remediated by the appropriate class of removalist prior to commencement.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 82 of 94
LEAD PAINT
Introduction
Lead in paint (as lead carbonate) is found extensively in homes and commercial and industrial buildings built pre-1970. Although Australian industry has generally phased out lead content in paint, levels of below 1 percent are still permitted and industrial application of high-lead paint to residential/commercial dwellings may still continue.
Lead-based paint may be a health issue if it becomes mobile in the environment or if ingested. For this reason, sealing or safe removal of paint is strongly recommended particularly where it is flaking or exposed to the elements.
Assessment Criteria
Lead paint is defined by the Australian Standard (AS 4361.2 – 2017 Guide to hazardous paint management Part 2: Lead paint in residential, public and commercial buildings) as a paint or component coat of a paint system containing lead or lead compounds, in which the lead content (calculated as lead metal) is in excess of 0.1% by weight of the dry film as determined by laboratory testing.
Lead Paint Management and Recommendations
The following information uses Australian Standard (AS 4361.2 – 2017) as the primary reference. Lead paint in residential and commercial premises may be managed in one of four ways:
Leave undisturbed
Stabilised (i.e. over painting or encapsulation)
Abated (i.e. removed)
A combination of the three management options may be required
Should removal be chosen, a high degree of skill, preparation and risk minimisation is required to avoid lead exposure, as dry sanding of lead levels as low as 0.1% can generate high lead dust. Therefore, the Wet Scraping and Wet Sanding methods are amongst the safest methods available.
Strict adherence to the guidelines described in AS 4361.2 – 2017 will best ensure minimisation of risk. During this process personal protective equipment and waste containment equipment is essential and children, pregnant women and persons not directly engaged in the process should not be present. General workers may undertake this process providing they adhere strictly to the guidelines, however, a specialist lead paint removal contractor is recommended for extensive paint removal works.
Where remediation is required it is important to minimise ongoing maintenance costs by ensuring that the works are undertaken by a professional who is able to give a significant time guarantee of the painted surfaces at the completion of the works. The following website lists contactors by postcodes that have been included based on their indicated skills and training in working safely with lead paint. http://www.lead.org.au/paintersall.html. These contractors should however be assessed by current performance prior to engagement.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 83 of 94
Responsibilities of Owners and Contractors
According to AS 4361.2 – 2017 owners of residences or commercial buildings that may contain lead should:
Manage the property in such a manner as to effectively control any health risk to occupants, contractors or others
Ensure occupants are sufficiently informed about and protected from the hazards associated with lead paint
If management work is to be undertaken, inform immediate neighbours about the nature of the work
Contractors should:
Obtain appropriate accreditation to undertake the proposed level of remedial work involving lead paint and have the required level of specialized training
Undertake the contracted work in such a way as to protect the health and safety of employees, tenants and the general public
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 84 of 94
SYNTHETIC MINERAL FIBRE
SMF refers to man-made mineral fibrous materials commonly used for their insulating and reinforcing properties. The amorphous (non-crystalline) materials include glass fibre, mineral wool and ceramic fibre products.
Discussion
Although glass fibre is classified as an irritant, levels of airborne fibreglass during routine occupation of the premises would be insignificant. During any large-scale installation or removal of fibreglass insulation, providing SMF fibre suppression measures as defined below are employed, exposure standards for SMF fibre would not normally be exceeded.
The following Risk Assessment is based on the requirements of Worksafe Australia, WorkSafe Australia, Sydney 1990, Synthetic Mineral Fibres: National Standard and National Code of Practice.
SMF Risk Assessment
According to Worksafe Australia 1990 (p 9) health risks associated with SMF are "significantly less potent … than white asbestos (Chrysotile) fibres” and that "...the possibility of lung cancer is eliminated at an exposure standard (time weighted average) of 0.5 respirable fibres per millilitre of air for all types of synthetic mineral fibres...." (p V).
To reduce the possibility of skin, eye and upper respiratory tract irritation a maximum exposure standard of 2 milligrams per cubic metre of inspirable dust is recommended. These two standards are designed principally for the manufacture and end user industries in which significant dust clouds would be generated.
The same document also states: "The overall conclusion based on available animal experiments and epidemiology is that provided work is carried out in accordance with (NOHSC 1990), and compliance is maintained with the exposure standards, then there is a negligible health risk associated with exposure to SMF under present-day manufacturing and usage patterns."
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 85 of 94
PCB
PCB is the common name for Polychlorinated Biphenyls. PCBs range in appearance from colourless, oily liquids to more viscous and increasingly darker liquids, to yellow then black resins, depending on chlorine content of the PCB.
Discussion
The major use of PCBs in the electrical industry has been as an insulating fluid inside transformers and capacitors. These transformers and capacitors have ranged in size from the very large transformers typically used by electrical supply companies, to the small capacitors used in commercial products. Capacitors containing PCBs were installed in various types of equipment including fluorescent light fittings during the 1950s, 60s and 70s.
Risk Assessment
Small quantities of PCBs are usually found in sealed containers known as capacitors. PCB-containing capacitors are unlikely to pose a health risk, unless they become damaged and leak.
PCBs can enter the body in three ways: absorption through the skin inhalation of PCB vapour ingestion by contamination of food or drink
The most commonly observed symptom in people exposed to high levels of PCBs is a condition known as chloracne. This is a severe, persistent acne-like rash due to repeated and prolonged contact of PCBs with skin. This condition has also occurred in people who have accidentally ingested PCBs.
Very high exposure to PCBs may also cause liver damage and damage to the nervous system.
There is the possibility that PCBs may cause cancers.
The likelihood of becoming sick from PCB exposure increases with the length of time and the amount of material that a person might come in contact with.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 86 of 94
OZONE DEPLETING SUBSTANCES
Introduction
Ozone depleting substances (ODS) are compounds that contribute to stratospheric ozone depletion. They are widely used in refrigerators, air-conditioners, fire extinguishers, in dry cleaning, as solvents for cleaning, electronic equipment and as agricultural fumigants.
Ozone depleting substances (ODS) include: Bromochloromethane (BCM) Carbontetrachloride (CCl4) Chlorofluorocarbons (CFCs) Halons Hydrobromofluorocarbons (HBFCs) Hydrochlorofluorocarbons (HCFCs) Methylbromide (CH3Br) Methylchloroform (CH3CCl3)
ODS are generally very stable in the troposphere and only degrade under intense ultraviolet light in the stratosphere. When they break down they release chlorine or bromine atoms which then deplete the ozone.
Ozone Protection Strategy
The Australian Strategy for Ozone Protection calls for personnel who handle, install, service, commission and decommission and maintain commercial and industrial refrigeration and air-conditioning equipment to be accredited, licensed, registered to work with ozone depleting substances.
Best Management Practices
In Australia a ‘Code of Good Practice’ has been drawn up with the objective of assisting the reduction of emissions into the atmosphere of substances that deplete the ozone layer and contribute to global warming.
The Australian Refrigeration and Air-conditioning Code of Good Practice (HB 40.1 – 2001) recommends best practice for the maintenance, design, servicing, labelling and manufacture of refrigeration and air conditioning systems towards this objective.
Legislation
Under the Federal Government’s Ozone Protection and Synthetic Gas Management Act 1989 and its Ozone Protection and Synthetic Gas Legislation Amendment Bill 2003 it is illegal to vent an ODS (Scheduled Substances) to the atmosphere.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 87 of 94
General Maintenance
All refrigeration and air-conditioning plant should be regularly inspected for traces of leaking refrigerant and/or oil, and for signs of leak-indicating dye
Whenever a system is charged with refrigerant and/or lubricant, the service person must clearly label the system with the refrigerant/lubrication type; name of service organization; and date of service. In addition, the ASHRAE/ARI refrigerant designated R number shall be clearly displayed
A service person should be aware of the possibility that a refrigeration or air-conditioning system may have been incorrectly charged or incorrectly labelled. The type of refrigerant contained in the system must therefore be first established by checking the temperature/pressure relationship or by using other tests to verify that the labelling is correct
Advice to Equipment Users
Users are advised that persons who service refrigeration and air-conditioning equipment are required by legislation to observe the Code of Good Practice and not to ‘top-up’ or ‘charge’ systems known to be leaking refrigerant, or to service equipment unless it can be returned into service in a leak-free condition
If a user does not have trained staff to undertake service or maintenance work, then it is recommended that a routine maintenance agreement for their plant be undertaken with a reputable service organization
All users should monitor the operation of their installation weekly and call the service person immediately if any abnormal condition is found
When a refrigeration system contains in excess of 50 kg of refrigerant, that system should be leak tested on a quarterly basis
Leak Testing
Various methods may be used for leak-testing, e.g. electronic leak detectors, halide lamp and or ultraviolet lamp
Only a non-controlled refrigerant mixed with a pressurising substance such as dry nitrogen should be used to leak test refrigeration and air-conditioning systems
Where an air-conditioning or refrigeration system is found to be leaking and needs to be repaired, the vapour and/or liquid must first be recovered from the leaking system
Where pressurisation testing has determined that an air-conditioning or refrigeration system is not leaking, moisture and non-condensables must be evacuated from the system using dry nitrogen as the moisture absorber and either the deep or triple evacuation methods
All refrigerants shall be recovered and either recycled, reclaimed or held for disposal in an approved manner
It is highly recommended that a refrigerant charge monitor or leak detector be installed to alert equipment owners/operators of a refrigerant leak
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 88 of 94
Recovery, Recycling and Disposal of Refrigerants
It is highly recommended, and in some cases mandatory, for recovery and/or recycling equipment to be used for the removal and recovery of refrigerant during service
To avoid the danger of mixing different refrigerant types, the receiving containers shall be identified by the correct colour coding and labelling and shall only be used for the refrigerant type that is being transferred. The recovery containers shall conform to AS 4484-2004, ‘Gas Cylinders for Industrial, Scientific and Refrigerant use – labelling and colour coding’
As chillers have large internal volume, it is important that all refrigerant vapour be recovered. A chiller at atmospheric pressure can still hold many kilograms of refrigerant vapour after the liquid has been removed
When recovering refrigerant from a chiller the refrigerant should be recovered until the internal system pressure is reduced to 3 kPa absolute for low-pressure systems (e.g., R-11) and 70 kPa absolute for positive pressure systems (e.g., R-12 and R-22). The internal pressure should then be taken up to atmospheric pressure with dry nitrogen if the chiller is to be opened. This will prevent moisture–laden air entering the system, which could lead to contamination and corrosion
Disposal of Refrigerants
Unusable or surplus fluorocarbon refrigerant shall not be discharged to the atmosphere, but shall be returned to a supplier
Empty residual refrigerant in a disposable container shall be recovered and the container disposed of at a recycling centre
The utmost care must be taken to avoid mixing different types of refrigerants, as separation may be impossible and large quantities of refrigerant may be rendered unusable
Handling and Storage
Losses of refrigerant to the atmosphere can occur during the handling and storage of refrigerant containers. Service persons have a duty of care to avoid such losses.
There are numerous hazards associated with the storage of refrigerant. These include asphyxiation in confined space due to leakage from refrigerant containers; and fire, which may overheat and explode refrigerant containers or decompose refrigerant into toxic substances
Alternative Refrigerants and Lubricants
With the introduction of HFC alternative refrigerants, alternative lubricants need to be considered to ensure system reliability. Some of these alternative lubricants tend to exhibit greater hygroscopicity than mineral oils, so care must be taken to ensure they are kept in sealed containers at all times
Care must be taken to ensure that all components used in the refrigeration/air-conditioning system are compatible with the new refrigerant and lubricant
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 89 of 94
Recovery of Fluorocarbons Mixed with other Refrigerants
A number of different refrigerants and refrigeration mixtures have been used to replace or to ‘top up’ fluorocarbon based refrigerants in refrigeration and air-conditioning systems.
In many cases the equipment in question may not be labelled to indicate that hydrocarbon or hydrocarbon mixtures have been used and as the operating pressures of these replacement refrigerants are usually similar to those of the original refrigerant, their identification in the field is extremely difficult.
It is not safe therefore to recover flammable refrigerant (hydrocarbon) using equipment designed only for non-flammable refrigerants such as R-12 and R-134a
Should it be suspected that refrigeration or air-conditioning system contains an unidentified mixture or, if on asking the owner, examining the labels, and/or detecting instruments indicate that a hydrocarbon/fluorocarbon mixture or any other non-standard mixture of refrigerant may be present; the following procedure should be followed:
o If a hydrocarbon or flammable mixture that contains hydrocarbon is suspected, use only equipment designed for the recovery of flammable gasses and recover the refrigerant into a specially marked container
o In the case of refrigerant mixtures, it is not advisable to use recovery equipment as many mixtures have very high condensing pressures, which could result in equipment failure and/or injury to persons operating, or near the equipment
o The safest method of recovery is to use an evacuated and preferably chilled container to depressurise the system
o Label the container to show that it contains a mixture or the suspected composition, if known, and deliver it to a supplier for recycling
o Purge the residual gas from the system with dry nitrogen before proceeding with any repairs
Health Effects
In addition to causing environmental degradation certain ozone depleting substances may present a risk to human health when they are improperly handled or released in to a poorly ventilated area.
Inhalation
The most significant exposure route for humans is through inhalation. Refrigerant gases displace oxygen in the air making breathing difficult.
Overexposure can cause central nervous system depression and oxygen deficiency. Effects of overexposure may include light-headedness, giddiness, shortness-of-breath, headaches, and in extreme cases, irregular heartbeats, cardiac arrest, asphyxiation and death.
Symptoms of overexposure at lower concentrations may include transient eye, nose and throat irritation.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 90 of 94
Skin Contact
Contact with rapidly released refrigerant gas may cause frostbite. Symptoms of frostbite may include changes in skin colour to white or greyish yellow.
Other direct dermal contact may result in skin de-fatting, dryness, irritation or contact dermatitis.
Standard work clothes provide adequate protection of the skin but it is recommended that lined butyl gloves and goggles be used whenever handling liquid refrigerants.
Eye Contact
Eye contact with rapidly released refrigerant or air-conditioning gas may cause severe frostbite damage to eyes and eyelids. Eye irritation may occur if exposure occurs at lower concentrations.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 91 of 94
FUEL STORAGE FACILITIES In the ACT the management of fuel storage tanks is regulated by ACT WorkSafe who administers the Dangerous Substances Act 2004 and the Dangerous Substances (General) Regulation 2004. Heating oil and other petroleum products are classified as a Dangerous Substance under the ACT Dangerous Substances Act 2004. The Dangerous Substances (General) Regulation 2004 – Division 2.4.2-233 Decommissioning (applies to a container used to store a dangerous substance) states the following: ‘The container is thoroughly cleaned so that the container is in the condition it would be in if it had never contained the substance’; This would be difficult to achieve therefore it is advantageous to remove the tank. In the ACT, Environment Protection and Heritage prefers underground fuel storage tanks be removed once they are no longer in use, unless there are extenuating circumstances i.e. their removal undermines permanent infrastructure. This is also emphasized in the Australian Standard The Removal and Disposal of Underground Petroleum Storage Tanks (AS 4976-2008). Further, the ACT Environment Protection Authority (Environment Protection and Heritage) which administers the Environment Protection Act 1997 which contains contaminated land provisions responsible for the development of policy and guidelines to facilitate best practice when it comes to the management of contaminated land. Environment Protection and Heritage deems all sites known to have had fuel storage facilities as potentially contaminated until investigated and assessed and shown to be free of contamination. Based on this information and for the long-term management of the sites with fuel storage tanks, Robson Environmental Pty Ltd recommends that the USTs be removed in accordance with the requirements of ACT WorkSafe and Environment Protection and Heritage. Removal of the UST does require approvals from relevant ACT Government agencies which include: ACT Planning and Land Authority (ACTPLA) ACT WorkSafe - Dangerous Goods Unit.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 92 of 94
15 GLOSSARY
ACM See asbestos containing material Air monitoring Air Monitoring means airborne asbestos fibre sampling to assist in
assessing exposures and the effectiveness of control measures. Air monitoring includes exposure monitoring, control monitoring and clearance monitoring. Note: Air monitoring should be undertaken in accordance with the Guidance Note on the Membrane Filter Method for Estimating Airborne Asbestos Fibres [NOHSC:3003 (2005)]
Airborne asbestos fibres Any fibres of asbestos small enough to be made airborne. For the
purposes of monitoring airborne asbestos fibres, only respirable asbestos fibres (those less than 3µm wide, more than 5µm long and with a length to width ratio of more than 3 to 1) are counted.
Amosite Grey or brown asbestos AR See Asbestos Register Asbestos Containing Material Any material, object, product or debris that contains asbestos. Asbestos Register Inventory of ACM by type, form, location, risk and required action. Asbestos Removalist A competent person who performs asbestos removal work. Note: an
asbestos removal licence is required in all State and Territory jurisdictions.
Asbestos Survey and Management Plan
Document covering the identification, risk evaluation, control and management of identified asbestos hazards, developed in accordance with current legislation.
Asbestos2 The fibrous form of mineral silicates belonging to the serpentine and
amphibole groups of rock-forming minerals, including actinolite, amosite, anthophyllite, chrysotile, crocidolite, tremolite or any mixture containing one or more of the mineral silicates belonging to the serpentine and amphibole groups.
Asbestos–cement (AC) Products consisting of sand aggregate and cement reinforced with
asbestos fibres (e.g. asbestos cement pipes and flat or corrugated asbestos cement sheets).
ASCC See Safe Work Australia Council Non-friable asbestos ACM that is bonded into a stable matrix and cannot be reduced to a
dust by hand pressure. Chrysotile White asbestos Clearance inspection An inspection, carried out by a licensed Asbestos Assessor, to verify
that an asbestos work area is safe to be returned to normal use after work involving the disturbance of ACM has taken place. A clearance inspection must include a visual inspection, and may also include clearance monitoring and/or settled dust sampling.
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 93 of 94
Clearance monitoring Air monitoring using static or positional samples to measure the level of airborne asbestos fibres in an area following work on ACM. An area is ‘cleared’ when the level of airborne asbestos fibres is measured as being below 0.01 fibres/mL.
Control monitoring Air monitoring, using static or positional sampling devices to measure
the level of airborne asbestos fibres in an area during work on ACM. Control monitoring is designed to assist in assessing the effectiveness of control measures. Its results are not representative of actual occupational exposures, and should not be used for that purpose.
Crocidolite Blue asbestos Exposure monitoring Air monitoring in the breathing zone to determine a person’s likely
exposure to a hazardous substance. Exposure monitoring is designed to reliably estimate the person’s exposure, so that it may be compared with the National Exposure Standard.
HMSMP See hazardous material survey re-inspection and management plan In situ2 Fixed or installed in its original position, not having been removed. Inaccessible areas Areas which are difficult to access, such as wall cavities and the
interiors of plant and equipment. Licensed Asbestos Assessor Person who is qualified to undertake the identification and
assessment of asbestos and provide recommendations on its safe management.
Membrane A flexible or semi-flexible material, which functions as the
waterproofing component in a roofing or waterproofing assembly. NATA National Association of Testing Authorities NOHSC (now SWA) National Occupational Health and Safety Commission (now known as
Safe Work Australia) PMCW Person with management or control of a workplace Safe Work Australia Council (SWAC)
A council that provides a national forum for State and Territory governments, employers and employees to consult and participate in the development of policies relating to OHS and workers' compensation matters, and promote national consistency in the OHS and workers' compensation regulatory framework.
SWMS Safe Work Method Statement
Hazardous Materials Survey & Management Plan
Client: ANU H2203_T-07207_Building 38 - Physics Building-20190218 Page 94 of 94
16 REFERENCES
How To Manage and Control Asbestos In The Workplace Code of Practice
How To Safely Remove Asbestos Code of Practice
Work Health and Safety Act 2011
Work Health and Safety Regulations 2011
Australian Capital Territory Parliamentary Counsel (2006), Asbestos Legislation Amendment Act 2006 [A2006-16], Canberra, Australia
ANZECC 1997, Identification of PCB-Containing Capacitors; An information Booklet for Electricians and Electrical Contractors
Guide to Hazardous Paint Management Part 2: Lead paint in residential, public and commercial buildings Standards Australia, AS 4361.2 – 2017
Standards Australia, HB 40.1 – 2001 The Australian Refrigeration and Air-conditioning Code of Good Practice
WorkSafe Australia, Sydney 1990, Synthetic Mineral Fibres: National Standard and National Code of Practice
5. Future Inspection Reports and Certificates
Robson Environmental Pty Ltd ~ ABN: 55 008 660 900 ~ www.robsonenviro.com.au p: 02 6239 5656 ~ f: 02 6239 5669 ~ [email protected] PO Box 112 Fyshwick ACT 2609 ~ 140 Gladstone Street Fyshwick ACT 2609
Hazardous Materials Report HMR304
T07837_38PhysicsBuilding_MA_20190614
Brett Morrison
Australian National University
Canberra ACT 2600
Date of Report: 14 June 2019
Dear Brett
Re: Analysis of vinyl floor tiles in Room 163 and Room 164 in Building 38 Physics Building, at the Australian National University on 14 June 2019
Site Work Jordan Curbishley Asbestos Assessor from Robson Environmental sampled suspected asbestos containing material(s) (ACM) from the above location(s). The analytical results are presented in Table 1: Sample Analysis Results and photographs in Appendix 1: Photograph(s) of Non-ACM.
Material Assessment Restrictions and Caveats
Robson Environmental has taken care to ensure that this report includes the most accurate information available. This report does not constitute a full register of asbestos containing materials at the above premises as required by current legislation. The material assessments, recommendations and/or conclusions contained in this report must not be used to absolve a person of their responsibility to work in accordance with relevant Statutory Requirements, Codes of Practice, Guidelines, Safety Data Sheets, Work Instructions or reasonable work practices.
Laboratory Methodology The sampled material was double bagged and transported to Robson Environmental’s National Association of Testing Authorities (NATA) accredited laboratory with a Chain of Custody (COC) form written by the assessor which was signed off on receipt by the laboratory. The received material was analysed for asbestos fibre content which is determined by Polarised Light Microscopy with Dispersion Staining techniques. Refer to Appendix 2 for the Certificate of Analysis. The sample taken from suspected ACM is representative of the material sampled, individually identified, transported, analysed and reported in accordance with current legislation and Robson Environmental In-house Procedures for Fibre Identification and for Surveys and Bulk Sampling. All inspections, sampling, identification and reporting was undertaken in accordance with Robson Environmental’s NATA, ISO9001, ISO14001 and AS4801 accreditations.
Client: Australian National University T07837_38PhysicsBuilding_MA_20190614 Page 2 of 6
Table 1: Sample Analysis Results
Sample Number
Location Description Material Fibrous Content
C1621 Room 163 – Green floor tiles Vinyl floor tile No Asbestos Detected
C1622 Room 164 – Beige floor tiles Vinyl floor tile No Asbestos Detected
C1623 Room 164 – Green floor tiles Vinyl floor tile No Asbestos Detected
Asbestos containing material
Presumed asbestos containing material
Non-asbestos containing material
Conclusions & Recommendations The vinyl floor tiles sampled from Room 163 and Room 164 were found to be non-asbestos and no further action is required. Only specific materials sampled and analysed in the Robson NATA accredited laboratory can be completely defined as being ACM or Non-ACM. All remaining visually consistent materials in the same vicinity are presumed as being the same material. However this is not a definitive statement that these materials are ACM or Non-ACM. Extensive sampling may be advised in properties where construction materials used have not been consistent throughout.
Yours sincerely,
Jordan Curbishley – Licensed Asbestos Assessor #AA00039 Hazardous Materials Consultant Mobile: 0413 439 168
Client: Australian National University T07837_38PhysicsBuilding_MA_20190614 Page 3 of 6
Appendix 1 Photograph(s) of Non-ACM
Sample Number
Location Description Material Photograph(s)
C1621 Room 163 – Green
floor tiles Vinyl floor tile
C1622 Room 164 – Beige floor
tiles Vinyl floor tile
Client: Australian National University T07837_38PhysicsBuilding_MA_20190614 Page 4 of 6
Sample Number
Location Description Material Photograph(s)
C1623 Room 164 – Green
floor tiles Vinyl floor tile
Client: Australian National University T07837_38PhysicsBuilding_MA_20190614 Page 5 of 6
Appendix 2 Fibre Identification Certificate of Analysis
Client: Australian National University T07837_38PhysicsBuilding_MA_20190614 Page 6 of 6