Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Option Code
CFC
Accessory Deck Lid Spoiler Fiber Mirror caps 8V7.071.645.3Q0
Or 8V7.071.645.A.3Q0 8V0.072.530.C.3Q0 (with side Assist)
Application
2014+ A3 Cabriolet
Publication No. V 1.0
Installation Level L3
Installation Instructions Issue Date
Dec. 3, 2015
© 2015 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopy, recording or otherwise, not may these materials be modified or reposted to other internet sites, with the expressed written permission of the publisher.
Icon Legend:
ATTENTION: Read entire instructions thoroughly before starting Improper installation procedures may cause serious personal injury or damage to the vehicle.
• Installation should be performed only by a qualified technician. • Read all instructions thoroughly before starting. • Beware of sharp edges. • Always wear safety glasses to help protect eyes. • Always wear protective gear as gloves and use caution when using hand tools. • Before starting make sure painted and trim surfaces are protected to avoid scratching during
installation process of the items. Use proper surface protection covers and work attire free of dirt and grease.
• These add-on components must not be heated when drying! There is a risk of deformation. • Plan on deicing the add-on components overnight at (20°C) (68°F). • If you find parts that are miss-shaped, that have paint imperfections, or are not otherwise
acceptable, put them aside in a clean, organized manner so they can be returned to the suppliers. Report these parts weekly. Call in missing hardware. Extra parts will be shipped to you.
• During the installation process, close all doors, and remove the keys from the ignition. If you must open a door, trunk lid, etc., during the installation process, close the areas as soon as you are complete with the application in that area. Failure to do so could result in significant battery drain, and/or battery failure in the vehicle.
Note – special directives/notations
within the procedure, designed to assist.
Cautions, Warnings – Pay special attention
to the notations. Failure to, could result in damage to the part,
vehicle or person.
Audi Quality Check – Confirm that the step has been completed
and all quality standards have been
met.
Tip – a comment that may help the installer navigate
certain steps within a procedure.
Audi Accessories
Page 2 of 15
Kit Contents
A3 Sedan Fiber Mirror Caps 8V0-072-530-C -3Q0 A3 Sedan Deck Lid Spoiler: 8V7-071-645-3Q0 or 8V7-071-645-A -3Q0
Required Tools: Mirror Caps:
96030 Slotted Screwdriver with Precision Handle or Pick Tool
Plastic Pry Bar or Bone Tool T 10 Torx screwdriver
Audi Accessories
Page 3 of 15
Required Tools: Spoiler:
Towel ELCH Adhesive Kit PN: D 172 200 A2 or
D 172 200 A1
Isopropyl Alcohol (91%+)
ELCH Primer 146 PN: D 009 200 02
60-80 Grit Sandpaper Tape, 2”, low Adhesion, (3M Painters’)
Audi Accessories
Page 4 of 15
Mirror Cap Instructions
1.0 Unzip the cover around the driver side door and roll and secure out of the way.
1.1 • Unclip the cover starting in the center of the front
valance to the edge of the back door. • Roll up the cover over the mirror.
Note: Ensure there is no dirt, grease, etc., between the body cover and the vehicle.
1.2 Gently push the mirror glass out of the mirror adjustment motor using the 80/20 pry bar.
Attention: If not careful the glass will break. Do not pull, wire may be present.
Audi Accessories
Page 5 of 15
1.3 Disconnect the electrical connectors for heating the mirror.
1.4 Remove the mirror adjustment unit by unscrewing the center bolt with the T10 Torx screwdriver.
Note: Do not discard the screw. It will be reused for installation.
1.5 Detach the electrical connector to the mirror adjustment motor.
Attention: Do not pry on the plastic, or it may break.
1.6 Remove the 3 screws on the mirror trim with the T10 Torx screwdriver.
Note: : Do not discard the screw. They will be reused for installation.
Audi Accessories
Page 6 of 15
1.7 • Release the 4 retaining tabs (labeled as 2 in image). • In the mirror trim (labeled as 5) using a flat head pocket
screwdriver or pic tool (labeled as 1) in the direction indicated by the arrow and remove the mirror trim.
• Remove one clip at a time and softly pull the trim piece from the mirror while releasing.
1.8 • When applicable: remove the warning lamp for Audi
side assist. • Push the lamp from the inside out and detach the
electrical connector.
1.9 • Release the 3 retaining tabs (labeled as 2), and pull off
the mirror cap (labeled as 1) forwards in the direction indicated by the arrows.
1.10 Install the carbon fiber mirror cap in the reverse order you removed the factory mirror cap.
Note: Check for secure engagement.
Audi Accessories
Page 7 of 15
1.11 • When applicable: install the warning lamp for Audi side
assist. • Feed the electrical connector through the mirror cap
opening and connect with the warning lamp. Engage the warning lamp for Audi side assist (labeled as 2) in the decorative trim (labeled as 1).
1.12 • Reinsert the mirror trim piece pushing until it locks in. • Make sure the mirror heating wires are in Section (1,
left side of image) and the mirror adjustment unit harness in Section (2, right side of image).
1.13 • Reinstall the three saved screws from step 1.6 • This will hold the trim piece and tighten.
Note: Do not over tighten the screws, they will strip.
1.14 Reconnect the mirror adjustment unit, and insert the unit into the mirror making sure it’s aligned properly. Reinsert the screw from step 1.4 and tighten
Audi Accessories
Page 8 of 15
1.15 • Connect the electrical connectors for the heating unit
arrows in red on the rear side of the mirror glass. • Place the mirror glass on the mirror adjustment unit
motor and press the mirror glass into place. • See the direction indicated by the arrow. • The friction guides must engage with the friction
springs when the mirror glass is inserted.
1.16 Reinstall the full-body cover making sure all clips are in place, and driver side is zipped shut.
Note: • : Make sure the cover is zipped and secured in
place.
Audi Quality Check:
• Check vehicle operation • Using the VAS Diagnostics tool check for any vehicle faults. • Make sure both mirrors have full functionality and movement
Audi Accessories
Page 9 of 15
Spoiler Instructions:
Attention: Application Instructions for Adhesive
• The recommended processing temperature for the adhesive/3M adhesive tape and material is between 15° C and 25° C (59° F and 77°F).
• The bonding surfaces on the body and spoiler must be absolutely dry, clean, and free of wax, oil, or grease. • The bonding surfaces must be cleaned with Isopropyl Alcohol (91 %+) immediately prior to applying the
adhesive. • The installation process should be completed in 45 minutes after opening the adhesive.
2.0 Unzip the trunk area body cover around the rear of the vehicle.
2.1 Roll the full-body cover up and out of the way for spoiler installation.
NOTE: Ensure there is no dirt, grease, etc., between the body cover and the vehicle.
Audi Accessories
Page 10 of 15
2.2 Before fitting up the deck lid spoiler to the vehicle, clean rear hatch area where spoiler will be mounted to prevent any scratches to the vehicle.
2.3 Test fit the deck lid spoiler by placing and centering it on the deck lid. Align the deck lid spoiler so that it fully abuts the contact edges. This will also protect the vehicle from any adhesive residue.
2.4 • Position rear deck lid spoiler onto the rear trunk lid, align and check fitment to the vehicle. • Draw a reference mark using a wax pencil onto center of spoiler on 3M tape. This will set up spoiler location for
installation to the vehicle. • Confirm spoiler fitment. Re-apply spoiler to the vehicle using pervious marks to verify alignment.
Attention: It is very important that all spoilers are inspected before installation
Audi Accessories
Page 11 of 15
2.5 Inspect the spoiler. Make sure the release liner is not present for the installation. If so, it will need to be removed before sanding the spoiler.
Attention: It is very important that all application surfaces are free of wax and dirt.
2.6 Inspect the adhesive groove on the rear side of the spoiler. There may be damage present to the groove. If so, discard the spoiler and report to management.
2.7 After fitting the deck lid spoiler, thoroughly re-clean rear truck area with Isopropyl Alcohol (91 %+) for final assembly.
Audi Accessories
Page 12 of 15
2.8 Roughen the adhesive groove on the rear spoiler and remove any residue that may be present to the groove. Remove sanding dust.
2.9 After sanding, clean all bonding surfaces on the spoiler using the Isopropyl Alcohol (91%+).
Audi Accessories
Page 13 of 15
2.10 Apply a coat of primer 146, PN: D 009 200 02 to the bonding groove surface of the spoiler. Leave to air dry for at least ten minutes.
2.11 Apply an even bead of adhesive, approximately 3mm to the bonding surface. Elch P-1 adhesive. PN:D 172 200 A2 or D 172 200 A1
Attention: The deck lid spoiler must be fixed to the vehicle within 15 minutes.
2.12 • Bring and position the deck lid spoiler onto the rear trunk lid. Use the pervious alignment mark to center the deck lid
spoiler to the rear trunk of the vehicle. • Firmly press the deck lid spoiler into place onto trunk from the center and working outwards. Be sure there is equal
spacing on the ends of the deck lid spoiler to the trunk of the vehicle.
Audi Accessories
Page 14 of 15
2.13 Secure the spoiler in place to the trunk lid with the 3M painter’s low adhesive tape. Be sure no gaps appear.
2.14 • Use a putty knife, cotton cloth, and light use of isopropyl alcohol to remove any adhesive residue. • Make a final inspection to ensure no gaps greater than 2.0mm exist and gaps are consistent from side to side.
Audi Accessories
Page 15 of 15
Attention: • Do not remove adhesive tape for 12 hours • No mechanical load may be applied to the roof
spoiler for 24 hours • No vibrations to the adhesive for 12 hours - any
required manoeuvring at max. walking speed. • Wait at least 12 hours before removing the
adhesive • tape; protect the vehicle from water for 12 hours. • The add-on components must not be subjected
to any mechanical load for 24 hours. • Do not wash the vehicle for 48 hours. • The add-on components may work loose and
detach when the vehicle is in motion if the adhesive reaction time is not observed — risk of accident.
2.15 • Unroll full-body cover over the hatch lid, and zip it closed. • The guidelilnes above apply to vehicle moving and care of the vehicle after spoiler installation.