ACCESSORY INSTALLATION AND PRODUCT MAINTENANCE

B E S T B AT H S H O W E R A N D T U B

www.bestbath.com | 800.727.9907 723 Garber Street | Caldwell, ID 83605

1034

ACCESSORY INSTALLATION AND PRODUCT MAINTENANCE

TABLE OF CONTENTS

Seat and Grab Bar 2

Soap Dish – Surface Mount 3

Soap Dish – Corner Mount 4

WaterStopper – Standard Application 5

WaterStopper – Corner Application 6

Semi-Permanent Threshold Adaptor 7

Curtain and Rod 8

Standard 26" Glide Bar 9

Flange Trim Kits:

for Wing Wall 10

for Remodel 11

with Reveal 12

for New Construction 13

Window Trim Kits:

up to 37" width 14

up to 73" width 15

Cleaning and Maintenance Recommendations 16

This guide includes installation instructions for Bestbath accessory products plus recommendations for cleaning and maintaining your Bestbath tub or shower.

These instructions are also available at: www.bestbath.com/resources and in video format on youtube.

For Bestbath warranty information, visit www.bestbath.com

NOTE: This complete set of installation instructions is shipped with every Bestbath accessible unit. Not all products covered here will necessarily apply to your purchase.

http://www.bestbath.com

http://www.bestbath.com/resources

http://www.bestbath.com

Page 2

1075

Seat and Grab Bar

• Folding seat, with or without swing-down legs • Grab bar • Grab bar wall flanges (2)

I N S TA L L AT I O N I N S T R U C T I O N S

• Tape measure • Marker or pencil • Screw gun • 7⁄32" bit • 1⁄4" bit • #2 Phillips bit • 5⁄16" socket

• 100% silicone • Caulk gun • #10 x 11⁄4" Phillips-head stainless steel sheet metal screws (7) • #10-32 x 11⁄4" stainless steel cap screws (2) • #10-32 T-nuts (2)

If seat or grab bar location is predrilled:With some models, the seat or grab bar location may be pre-drilled, just through the first layer of fiberglass. In those cases, do not drill any further into the wood. Simply apply silicone as shown and attach using the supplied fastener.

If seat or grab bar location is NOT predrilled or marked:1. The seat should be installed 18" above the floor. Install the

grab bar 34" above the floor to ensure that the seat will not swing up and hit the grab bar (Figure 1). Use a pencil to mark the seat flange and bracket hole locations on the wall.

2. Make sure the spot where the seat or bar is being attached has plywood backing. To test for plywood, barely drill through the fiberglass with a 7⁄32" bit, just until you see a few wood shavings. Do not pre-drill all the way into the wood. If you cannot locate any wood, see Installation Notes below.

3. Apply a half-circle of silicone to the flanges above the two top screws and around the lower hole (Figure 2).

4. Install the seat/bar with the screws, making sure you can feel resistance from the plywood as the screws go in (Figure 3).

5. Adjust the feet to ensure that all four are touching the floor and then tighten the jam nuts. Failure to do so may result in injuries to the user and/or damage to the shower that will not be covered by the warranty.

Installation Notes:•When installing the grab bar, at least one of the three flange

screws in each flange must hit wood. If it does not, try drilling an additional test hole in the flange closer to the other holes. Alternatively, use a suitable blind fastener (toggler or WingIts®).

•Do not install a fold-down seat without swing-down legs unless at least one of the three flange machine screws (with a T-nut) is attached to wood backing. If your unit does not have wood backing where you need it, install 2x6 blocking between the studs to provide suitable attachment.

•If you cannot locate or add suitable backing, you can install grab bars and seats (with swing-down legs only) using a WingIts® brand fastening system, also available from Bestbath.

•Loads in excess of 250 lbs. always require a seat with swing-down legs.

SUPPLIES AND TOOLS NEEDED:

HOW TO INSTALL

ACCESSORY KIT CONTENTS:

WingIts is a registered trademark of WingIts Innovations, LLC.

Silicone

Figure 2

#10 x 11⁄4" stainless Phillips-head sheet metal screw (only for seats with legs).

Fiberglass laminate

Plywood backing

Figure 3

Make sure seat will clear bar

34"

18"

FOLDING SEAT WITH SWING-DOWN LEGS

Figure 1

Page 3


SUPPLIES AND TOOLS NEEDED:


Trace line

Tape

HOW TO INSTALL1. Hold the soap dish level, at the desired location on the tub/

shower wall, and trace around it with a pencil.

2. Tape off around the traced area as shown at right.

3. Clean both the area within the tape and the contact edge of the soap dish with a solvent such as alcohol or acetone.

4. Scuff the area with sandpaper, then blow or brush off sanding dust so surface is clean for application of epoxy adhesive.

5. Mix epoxy according to instructions on the package.

6. Spread adhesive on the back of the soap dish and press it into position. Hold it there while you use your free hand to quickly remove the masking tape and the excess adhesive on it.

7. Continue holding the soap dish in place for a few minutes more until you feel it has set up enough to remain adhered. Alternatively, secure it with hot-melt glue while the adhesive cures.

8. When the adhesive has cured to the point of being fairly solid (approx. 5 minutes), apply a small bead of silicone where the soap dish and the shower wall meet.


1076

Soap Dish (Surface Mount)

• Sandpaper • Cleaning solvent (alcohol or acetone) • Masking tape • Rags or paper towels • Tape measure • Hot-melt glue gun (optional)

• Soap dish • 2-part, 5-minute epoxy • 100% silicone

Page 4



HOW TO INSTALL1. Hold the soap dish level (or slightly tipped forward) at the

desired location on the tub/shower wall. Using a pencil, trace the edge on one side of the dish (Figure 1).

2. Hold the dish on the line you drew and install the screws on that side. Screws should be snug but not tight (Figure 2).

3. Hold the dish level and trace the opposite edge (Figure 3).

4. Hold the dish on the line you drew and install the second set of screws. Then tighten all four screws (Figure 4).

5. Apply silicone sealant along the sides from the top but leave the corner open to allow drainage (Figure 5).

1082

Soap Dish (Corner Mount)

• Soap dish • 100% silicone • Screws (4)

SUPPLIES AND TOOLS NEEDED: • Pencil

Leave back corner free of caulk to allow drainage.

Figure 5 Apply silicone along top edge of sides.

Figure 1

Hold dish level and trace one edge with a pencil

Figure 3

Trace opposite edge

Figure 2Install screws snugly, but not tight

Figure 4Install two remaining screws, then tighten all four screws

Level (not supplied)

Level (not supplied)


1077

Page 5

(Standard Application)

• Alcohol wipes (2 included in kit) • E-6000 adhesive (included in kit) • Pencil • Scissors or utility knife • Straight edge

NOTE: Adhesion may be poor on surfaces (tile) treated with silicone-based sealers. To test adhesion, peel back about 1" of the WaterStopper backing, press adhesive area to surface where it will be installed and leave it overnight. Check the test sample by pushing sideways as shown at right. If it has adhered sufficiently, pull straight up and proceed with the installation. If it has not adhered, more agressive chemical stripping may be necessary.

21⁄4" radius

3⁄8" radius

Clean surface with supplied alcohol wipe (SURFACE MUST BE DRY).

1

Use a pencil to draw the outline of the endcap on the shower.

3

Draw a line with a straight edge that connects the two marks from Step 5.

6

When you reach the arrow mark at the other end, cut off any excess material and firmly press the end to the floor. Move along the length pressing firmly down on both sides of the WaterStopper.

9

Choose the end caps that fit your unit. Without removing adhesive backing, place endcap so it is level at the curb edge and inside the shower front. Note the distance from the front of the shower for second endcap.

2

Mark the floor at the embossed arrow.

4

Peel off about 4" of the adhesive backing from the WaterStopper and stick the corner at the two intersecting marks.

7

Peel the backing off the self-adhesive tape on the endcaps.

10

Press the endcaps down inside the drawn outline. Make sure the upright portion of the WaterStopper is slotted properly into the endcap. Use the second alcohol wipe to remove any excess E-6000 adhesive and the pencil marks.

12

E600

E6000

Apply E-6000 adhesive on the edge around the bottom and inside the front slot.

11

The WaterStopper will be ready for use after four hours. The WaterStopper combined with a heavy duty, weighted curtain offers one of the best water retention system available.

13

Mark the floor at the edge of the underside indent at the open end of the endcap.

5

Using the line as your guide, continue to peel off the backing as you gently stretch the WaterStopper and stick it down along the line you drew.

8

Repeat Steps 2 through 5 with the second endcap at the other end of the shower.

Too highToo low

KIT CONTENTS AND SUPPLIES:


Page 6

(Corner Application)1078

To begin, refer to Steps 1 – 6 on the WaterStopper Standard Application instructions.

Lay the WaterStopper along the front of your shower, leaving equal excess at each end.

Extend your pencil mark onto the vertical surface.

This is an example of a cut for a 90° corner shower.

With one finger or thumb in the inside pit of the cut, press the WaterStopper down onto the shower.

Mark the WaterStopper nearest the corner with a pencil.

From the angle templates at bottom of page, cut out the one that matches the angle of your shower.

Slice the backing about 6" on either side of the cut out. DO NOT cut through the adhesive strip or the rubber (see step 9).

Hold the center cut down with one hand and use the other to stretch tight and stick the exposed section of the adhesive down to the corner of your shower.

Follow Steps 3-10, using a scrap piece of wood or other hard surface between the shower floor and the WaterStopper to make your cut. Remove backing between cuts.

Place the template on the WaterStopper with the arrow pointing toward your mark and the parallel lines (=) flat against the outside edge. Trace the template.

Remove this section of the backing.

Run your thumbs or fingers along the outside bend, sticking the curled section down.

Holding the first angle firmly, pull tight and stick second corner down while making sure the front is straight. Continue with Step 12.

Use your razor knife to cut out the traced area. Make sure to start your cut on the vertical surface. If the WaterStopper does not fully bend to your angle, cut further into the vertical surface. DO NOT make cuts on your shower surface.

Bend the WaterStopper to your corner angle. Make sure that the outer edge curls up rather than down.

Your corner is finished. Continue with Steps 9-11 on the WaterStopper Standard Application instructions (FORM 1077) to add end caps and complete installation.

1

3

7

11

2

4

.

fi

12

13

90º90º

90° corner

Neo Angle

8

12

N1

5

9

13

N2

6

10

14

Scrap wood

For Neo-Angle Showers

Angle Templates:

90º90º

90° corner Neo-Angle

After Step 2, use the 45° template and refer to Steps N1 and N2 below.

Page 7



HOW TO INSTALL1. Put the adaptor in place and trace a pencil line around it on the

shower bottom (Figure 1).

2. Place a 1⁄4" bead of silicone just inside the pencil line.

3. Carefully put the threshold in position (Figure 2).

4. Smooth out the excess silicone with a wet finger. A strip of masking tape, positioned 1⁄4" from the pencil line on the shower and 1⁄4" from the edge of the adaptor, will help ensure a smooth edge and make excess silicone easier to remove (Figures 2 and 3).

5. Remove the masking tape and touch up with a wet finger to smooth and feather edges of the silicone.

6. Do not disturb for 12 hours.

To remove the adaptor:1. Holding the blade flat, carefully cut through all the silicone with

a utility knife.

2. Pivot the threshold sideways into the shower and pull it up.

3. Carefully remove the silicone with a single-edged razor blade and Goof Off® Remover or other caulk remover (available at most hardware stores).

SUPPLIES AND TOOLS NEEDED: • Pencil • Masking tape (optional)

• Threshold adaptor • 100% silicone

1079

Semi-Permanent Threshold AdaptorPart Numbers TAS, TASW, and TASM

Masking tape

Figure 3

1⁄4"

1⁄4" bead of silicone Masking tape

on shower wall and pan.

1⁄4"

Figure 2

Goof Off is a registered trademark of W.M. Barr Company Inc.

Pencil line

Figure 1

Threshold adapter

Page 8



HOW TO INSTALL • Cut the curtain rod to the correct length based on whether it will be installed on the walls of the shower or on the walls above the shower unit. • Use screws to attach a bracket at the right level on each side of the shower unit (or wall above).

• Curtain rod • Curtain rod bracket (2) with screws

1080

Curtain and Rod

Plastic curtain rod bracket

Curtain must be 74" long (sold separately)

74"75"

Curtain rod

Curtain ring (sold separately)

Position horizontally so the curtain hangs against the inside of the WaterStopper.

2"

Page 9



HOW TO INSTALL

1081

•Refer to Figures 1 – 3 below.

• Glide bar assembly • #10 x 1" TEK screws (2) • #10 x 3⁄4" Fender washers (2)

Standard 26" Glide Bar

DISASSEMBLE KIT PARTS

Figure 1

MARK AND INSTALL FLANGES

Figure 2

RE-ASSEMBLE GLIDE BAR ON FLANGES

Figure 3

KIT CONTENTS (ASSEMBLED)

Page 10


HOW TO INSTALL


MATERIALS & SUPPLIES NEEDED:

APPLICATION:

Flange Trim Kit for Wing Wall

• Back wall section • Typical side front sections (2) • Typical side top section • Universal side top section

• Wing wall top section • Loctite® Power Grab® construction adhesive • 100% silicone

• Paintable latex caulk

Installation:1. Measure the distance along the back wall between the drywall

on each side of the shower.

2. Trim the back wall section to the correct size with a hacksaw.

3. Apply dollops of Power Grab® adhesive, approximately 3⁄4" tall and spaced 8" apart, to the nailing flange. Press the trim in place.

4. Repeat Steps 1– 3 with the remaining sections.

5. Caulk around all edges. Use 100% silicone between shower and trim; use paintable latex between trim and drywall (Figure 3).

For use as an easy way of covering the nailing flange where drywall or other wall material is already installed BEHIND a shower with a wing wall.

1083

Loctite and Power Grab are registered trademarks of Henkel Corp.

Power Grab® adhesive

8"

Figure 1

TRIM CROSS-SECTION

1⁄8" radius11⁄4"

3⁄32"5⁄8"

Figure 2

LEFT WING WALL SHOWN

Figure 4

TRIM CROSS-SECTION (INSTALLED)

Shower

Screw headSilicone

Flange trim

Power Grab® construction adhesive

Shower nailing flange

Latex caulk (paintable)

DrywallFigure 3

Stud

Stud

TRIM SHOWN BEFORE INSTALLATIONMake sure you measure horizontal side pieces from the "step" and

not from the end. See dimension A below.

Page 11


HOW TO INSTALL



1084

Flange Trim Kit for RemodelPart Numbers FTKR3, XFTKR3, and FTKTR3

• Back wall section • Left front section • Left top section • Right front section

• Right top section • Loctite® Power Grab® construction adhesive (2) • 100% silicone


1. Measure the distance along the back wall between the drywall on each side of the shower.


3. Apply dollops of Power Grab® adhesive, approximately 3⁄4" tall and spaced 8" apart, on both the nailing flange and drywall. Press the trim in place.


5. Clear away any excess adhesive, then caulk around all edges. Use 100% silicone between shower and trim; use paintable latex between trim and drywall (Figures 3 and 4).

For use on remodels where dry wall is either: – cut out to install the shower (Figure 3); or – damaged in such a way that it will not be concealed by our narrower 11⁄4" FTK125 molding kit (Figure 4).

Kit Part Number Shower HeightFTKR3 42" to 83"XFTKR3 83" to 941⁄2"FTKTR3 15" to 42"


8"

Drywall

TRIM CROSS-SECTION

1⁄8" radius

3"

3⁄32"

3⁄8"

Figure 2

TYPICAL TRIM CROSS-SECTION (INSTALLED)

Stud

Stud

Shower

Screw head

Screw head

Silicone

Flange trim





Drywall

Figure 3

NON-TYPICAL TRIM CROSS-SECTION, INSTALLED ON SHOWER OVER DAMAGED DRYWALL

Shower

Screw head

Screw headSilicone

Flange trim





Drywall

Stud

Stud

Figure 4

Dam

aged

dry

wal

l

Use when drywall is damaged beyond coverage with the 11⁄4" kit.

Figure 1


APPLICATION:



Page 12


APPLICATION:

HOW TO INSTALL

1085

Flange Trim Kit with RevealPart Numbers FTK125RVL and FTK125DRVL

MATERIALS & SUPPLIES NEEDED: • Paintable latex caulk


8"

Installation:1. Measure the distance along the back wall between the drywall

on each side of the shower.

2. Trim the back wall section to size with a hacksaw.



5. Clear away any excess adhesive, then caulk around all edges. Use 100% silicone between shower and trim; use paintable latex between trim and drywall (Figure 3).

For use as an easy way of covering the nailing flange on showers or tub/showers with one or two reveal-type flanges where drywall or other wall material is already installed BEHIND the unit.

Figure 1

TRIM CROSS-SECTION

1⁄8" radius11⁄4"

3⁄32"5⁄8"

Figure 2

RIGHT REVEAL SHOWN

Figure 4

Drywall

ACCESSORY KIT CONTENTS: • Non-reveal front section (2) • Non-reveal top section • Reveal front section (1 or 2*) • Reveal top section (1 or 2*)

• Back wall section • Loctite® Power Grab® construction adhesive • 100% silicone

* Doubles will have 2 sections.

Kit Part Number Type Shower HeightFTK125RVL Single reveal 42" to 823⁄4"XFTK125RVL Single reveal 83" to 941⁄2"FTK125DRVL Double reveal 42" to 823⁄4"XFTK125DRVL Double reveal 83" to 941⁄2"


Figure 3

Shower

StudScrew headSilicone

Flange trim




Drywall

Stud




Page 13


1086

• Back wall section • Left front section • Left top section • Right front section

• Right top section • Loctite® Power Grab® construction adhesive • 100% silicone


1. Measure the distance along the back wall between the drywall on each side of the shower.




5. Clear away any excess adhesive, then caulk around all edges. Use 100% silicone between shower and trim; use paintable latex between trim and drywall (Figure 3).

Kit Part Number Shower HeightFTK125 83" or lessXFTK125 83" to 941⁄2"


8"

Drywall

Figure 1

Flange Trim Kit for New ConstructionPart Numbers FTK125 and XFTKT125

For use as an easy way of covering the nailing flange where drywall or other wall material is already installed BEHIND a shower or tub-shower unit.

TRIM CROSS-SECTION

1⁄8" radius11⁄4"

3⁄32"1⁄2"

Figure 2


Shower

Stud

Stud

Screw head

Silicone

Flange trim




Drywall

Figure 3


APPLICATION:

HOW TO INSTALL





Page 14



1088

Window Trim Kit — up to 37" widthPart Numbers WTK37 and WTK37H (with header)

HOW TO INSTALL1. Cut side pieces (B) to length and width (Figure 3). For

cut edges that will not be covered with silicone, use a jig saw with a bi-metal blade to help prevent a rough edge; otherwise use a power saw.

2. Install side pieces with Power Grab® adhesive and brace or tape as needed until the adhesive hardens.

3. Cut sill piece (A) to length and width (cut slightly narrower than side pieces) and install tipped forward approximately 2° (or 1⁄16" – 1⁄8") for water run-off (Figure 4).

4. Cut top trim pieces (C) to fit and install (Figure 5).

5. Caulk all joints and corners with silicone (Figure 5).

• A 36" long sill with 92° angle for drain-off; radii at left end • B 36" long side with 90° angle (2) • C Top trim (2) not included with header kit • D Loctite® Power Grab® construction adhesive • E 100% silicone

Optional header components: • F 36" long sill with 90° angle • G #8 x 11⁄2" header mounting screws (4)

CDPower Grab

E

F 90° sill piece for header

B

34"

A

Radii

92°

36"

G

x4

37" max.

B Sides cut to fit

Loctite Power Grab is a registered trademark of Henkel Corp.

CROSS-SECTION: SILL PIECE (A)

2"

8"

1⁄2"

92°

Figure 1

CROSS-SECTION: SIDE PIECE (B) (and optional header)

2"

8"

5⁄8"

90°

Figure 2

Figure 5

Caulk with silicone

Caulk

C Top trim, cut to fit

G Pre-drill holes

F Optional header

1⁄8" -1⁄4"

Cut sill piece 1⁄8"–1⁄4" narrower than sides for cleaner caulking at corners.

88° A Sill cut to fit

Figure 4Figure 3

OPTIONAL HEADER

Page 15



HOW TO INSTALL1. Cut side pieces (B) to length and width (Figure 3). For cut

edges that will not be covered with silicone, use a jig saw with a bi-metal blade to help prevent a rough edge; otherwise use a power saw.

2. Install side pieces with Power Grab® adhesive and brace or tape as needed until the adhesive hardens.

3. Cut sill pieces (A1, A2) to length and width (cut slightly narrower than side pieces) and install tipped forward approximately 2° (or 1⁄16" – 1⁄8") for water run-off (Figure 4).

4. Cut top trim pieces (C) to fit and install (Figure 5).

5. Caulk all joints and corners with silicone (Figure 5).

• A1 36" long sill with 92° angle for drain-off; radii on left end • A2 36" long sill with 92° angle for drain-off; radii on right end • B 36" long side with 90° angle (2) • C Top trim (2) not included with header kit • D Loctite® Power Grab® construction adhesive • E 100% silicone

Optional header components: • F1 36" long sill with 90° angle; radii on left end • F2 36" long sill with 90° angle; radii on right end • G #8 x 11⁄2" header mounting screws (4) • H #8 x 1⁄2" screws (4) with header connecting strip

1087

Window Trim Kit — up to 73" widthPart Numbers WTK73 and WTK73H (with header)

CDPower Grab

E

A2

Radii

F1, F2 90° sill pieces for header

Radii

Radii

B

34"

A1

Radii

92°

36"

G

x4

H

x4

Loctite Power Grab is a registered trademark of Henkel Corp.

CROSS-SECTION: SILL PIECE (A)

2"

8"

1⁄2"

92°

Figure 1

90°

CROSS-SECTION: SIDE PIECE (B) (and optional header)

2"

8"

5⁄8"

Figure 2

73" max.

B Sides cut to fit

Figure 3

Butt radiussed ends together

G Pre-drill holes

H Connecting Strip

(Pre-drill all holes; countersink when

necessary)

F Optional header

A Sill cut to fit

1⁄8" -1⁄4"

Cut sill piece 1⁄8"–1⁄4" narrower than sides for cleaner caulking at corners.

88°

Figure 4

Optional Header:

OPTIONAL HEADER

Figure 5

C Top trim cut to fit

Caulk

Caulk with silicone

Reorder #FORM1034 6/18Goof Off is a registered trademark of W.M. Barr Company Inc.

Bestbath and WaterStopper are registered trademarks of Best Bath Systems Inc. © 2018 Best Bath Systems Inc. All rights reserved.

B E S T B AT H S H O W E R A N D T U B

1089

Basic Cleaning

Best cleaning results are obtained by using automotive paste wax or gel gloss on the walls only. The walls of the shower bathing unit should be waxed before use and then once every two or three months. A furniture wax may also be used.

In almost all instances, polish or paste wax will remove dirt accumulated during normal use. If a cleaner is needed, use only a non-abrasive liquid. Cleaners designed specifically for fiberglass work very well.

! Do not apply wax to the floor of the shower, shower pan or tub! This could make the surface slippery and increase the risk of injury due to falling.

Stain and Residue Removal

•Stains or burns can be removed by using an automotive rubbing compound, which will also restore surface luster.

•Difficult stains may require light sanding with wet 600 grit or finer sandpaper prior to using rubbing compound.

•The label on the inside of the unit may only be removed by the occupant. The adhesive residue from this label can be removed with lighter fluid, nail polish remover or Goof Off® Remover (available at most hardware stores).

! Avoid using caustic drain openers/clog removers (such as Drano) as they can damage the surface if allowed to stand.

Cleaning and Maintenance Recommendations

It is important to perform regular cleaning and maintenance on your Bestbath® unit. Doing so will help ensure that continues to function at its best for many years. Read and follow the care and maintenance recommendations noted here and keep these care instructions for future reference.

•DO NOT apply wax to the floor of the shower, shower pan or tub, as it could make the surface slippery.

•DO NOT use caustic drain clog removers as they can damage the surface if allowed to stand.

CARING FOR YOUR BESTBATH SHOWER OR TUB

Documents

ACCESSORY INSTALLATION AND PRODUCT MAINTENANCE