Access Tools 2011-12 Car Opening Manual

Introduction

Always Use Eye Protection Safety first. Always use eye protection and leather gloves when needed.

Always use the Index!To find a vehicle look in the Index under Make first.For example: Ford or Toyota then go down the list alphabetically for example Ford Taurus or Toyota Camry.

Check For Method 2 Some vehicles have a second method that is shown as method 2 on the NEXT page for that opening.

Check For Alternate Methods Some vehicles have an Alternate methods that is shown as Alternate Method on the SAME page. These instructions can be found in the front of the book directly after the index Alternate Methods.

Check The V.I.N. Number The 10th digit of the Vehicle Identification Number shows the year of the vehicle. See chart below.

High Tech Tools/Access Tools 2011-2012

VIN Character - Model Year Codes1981 1982 1983 1984 1985 1986 1987 1988 1989 1990

B C D E F G H J K L 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000

M N P R S T V W X Y 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

1 2 3 4 5 6 7 8 9 A 2011

B 2012

C2013

D

How to Use the 2011-2012 Car Opening Manual

ACCESS LOCK-OUT MANUAL 2011-2012

Gro

up4

Group3 Group2 NewId Style PRI Diagram

Group4 Method - Method Page 2 NotesNotes

_ALTERNATE023_ALTERNATE 585 Style00 1 Alt23

ALTERNATE

ALT

ER

NA

TE

Method - Alt 23

_Alternate Method Alt 23 Using the 23 Tool

TOOL: Horizontal Linkage Tool- 231. Separate weather strip from glass with Strip Saver and Wedge.2.Point tip of tool towards the front of the car.3.Insert tool into the door cavity.4.Twist tool to hook top linkage with tip of tool.5.Turn tool handle toward rear of vehicle to move linkage forward.

Tool 23

ALT

ER

NA

TE

_ALTERNATE103-4_ALTERNATE 1214 Style00 1 Alt103-04

ALTERNATE Method - Alt 103-04

_Alternate Method Alt 103-04 Using the 103 & 104 Tool

Tool: Vent Window Tools 103 & 1041) Insert the Flat vent tool 104 directly under the vent window handle.2) Insert the Vent window tool 1033) Depress the vent window handle release button with the flat 104 Tool.4) Rotate the vent window handle with the 103 tool while maintaining the release button depressed.5) Insert your arm in through the open vent window to unlock the truck.

Tool 103-04

TaylorGang ((Beas))Typewritten Textxxx

TaylorGang ((Beas))Typewritten Text


ALTERNATE

ALT

ER

NA

TE

Method - Alt22


Tool: SMALL HOOK TOOL - 221. Separate the glass from the weather-strip.2. Point tool towards front of car.3. Lower the tool into the door while turning tool so handle of tool points away from car.4. Hook lock rod with tip of tool (see illustration).Watch the door lock button for movement. When you have hooked correct bell crank, you will see the door lock button move.

Tool 22

ALT

ER

NA

TE


ALTERNATE Method - Alt26


Tool: Double Tool 261. Separate glass from weather-stripping.2. Point tool towards rear of car.3. Lower the tool into car. (SEE FIG. FOR POSITION)4. Lift tool to contact door lock button.5. Lift tool to unlock door.

Tool 26


ALTERNATE

ALT

ER

NA

TE

Method - Alt35


TOOL: INSIDE ACCESS TOOL - 351. Insert wedge between glass and weather strip directly above door lock button inside of vehicle (see figure 1).2. Insert tool in door with tip facing the front of the vehicle (see figure 1).3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until V shaped portion of tool is beneath the window glass.5. Raise the tool until that the V shaped portion of the tool is entirely visible on the inside of the vehicle (see figure 3).6. Rotate the tool so that the tip is positioned in front of the door lock button (see figure 4).7. Pull on tool in order to slide the door lock button towards the front of the vehicle (see figure 5).NOTE: To aid in the removing of the tool, place the wedge between the glass and the weatherstrip on the inside of the door ne ar the tool. The tool will slide easily from the inside of the door.

Tool 35

ALT

ER

NA

TE




Tool: Tool 471. Separate glass from weather-strip ( Very tight fit, be very gentle ) .2. Point tip of tool towards front of car.3. Lower tool into the door.4. Twist tool handle to hook and bind lock linkage (see fig.).5. Pull up on tool while hooking door lock rod.NOTE: You should be watching the door lock button inside of the car. When you contact the correct rod, you will see the door lock button move. Instructions are for passenger side door.

INSER TION

Front PassengerDoor

Tool 47


ALTERNATE

ALT

ER

NA

TE

Method - Alt74


Tool: 741. Separate the glass from weather-stripping with a Strip Saver and Wedge.2. With the tip of the tool facing the rear of the car, lower tool into door.3. Lower tool deep into the door and turn the handle away from the car. Lift tool handle until working end of tool emerges from inside of the car.4. With working end of tool fully inside the car, hook door lock button with tool tip and lift to unlock the door.

Tool 74

ALT

ER

NA

TE

_ALTERNATE78Glass_ALTERNATE 1216 Style00 1 AltGm

ALTERNATE Method - AltGM

_Alternate Method Alt GM Using the Glassman Tool

Tool: Glassman Tool 1. Insert the Glassman Tool on the side of the unframed window . 2. Insert the tool into the cavity created by the Glassman Tool to protect the glass from damage . 3. Insert a Long Reach Tool (such as the 78, Flat Max or Long John Tool) into the opening. 4.Maneuver the tool to engage the door handle or, when available, the door lock release button. 5.Pull the handle or engage the lock release button to unlock the door.

Tool

Pull BackHandle toUnlock

Tool 78SG

_ALTERNATE78GlassV_ALTERNATE 1695 Style00 1 AltgmV

ALTERNATE

ALT

ER

NA

TE

Method - AltGMV

_Alternate Method Alt GMV Using the Glassman Tool Vertical Buttons

Tool: Glassman Tool with a Vertical button tool1 Insert the Glassman Tool on the side of the unframed window .2 Insert a loop type tool into the cavity created by the Glassman Tool to protect the glass from damage .3. Maneuver the tool to engage the door lock button5. Pull up on the button to unlock the vehicle.

Linkage

Tool 78SG

ALT

ER

NA

TE

_ALTERNATE78SG_ALTERNATE 1412 Style00 1 Altohj

ALTERNATE Method - AltOHJ

_Alternate Method Alt OHJ Using the One Hand Jack Tool & 78 Tool

TOOL: One Hand Jack Tool- 78SG 1.Use the One Hand Jack tool to separate the door frame from the body of the vehicle. 2.Insert the Air Wedge to wards the top of the door and inflate. 3.Remove the One Hand Jack Tool . 4. Insert a Long Reach Tool into the opening. 5.Maneuver the tool to engage the door handle or, when available, the door lock release button. 6.Pull the handle or engage the lock release button to unlock the door. Note this opening should only be used in emergency situations

Tool 78SG

_ALTERNATE78SGc_ALTERNATE 1876 Style00 1 StartMulti

ALTERNATE

ALT

ER

NA

TE

Method - Startmulti

_Alternate Method Using the Starter Air Jack & 78 Tool

InstructionsTool- 78SG With Starter Air Jack and Regular Air jack 1. Use the Starter Air Jack to create working room between the door frame and the vehicle Body Pillar 2. Insert the Air Jack and Inflate. 3. Remove the Starter air Jack 4. Insert a Long Reach Tool into the opening. 5. Maneuver the tool to engage pull the door Handle or button to unlock the door 6 Remove the long reach tool then deflate the Air Jack 7 Pull the outside Handle to unlock the door

Tool 78SG

ALT

ER

NA

TE



_Alternate Method Alt81 Using the 81 Tool

TOOL: Inside Access Button Lifter- 811. Insert wedge between glass and weather-strip near the door lock button.2. Insert tool in door with tip facing the rear of the vehicle .3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until shaped portion of tool is beneath the window glass.5. Raise the tool until that the shaped portion of the tool is entirely visible on the inside of the vehicle (fig-ure 3).6. Rotate the tool so that the tip is positioned next the door lock button and lift the button. Note : To aid in the removing of the tool, place the wedge between the glass and the weather-strip on the inside of t he door near the tool. The tool will slide easily from the inside of the door.

Tool 81


ALTERNATE

ALT

ER

NA

TE

Method - Alt57


Tool: Strap Tool 871. Insert Strip Saver between window and window strip.2. Cover front of the tool with another Strip Saver.3. Insert the tool into the door using the Strip savers4. Use the strings to help move the tip of the tool into position over the door lock button.5. Pull the tool to lift the door lock button

Tool 57

ALT

ER

NA

TE

_ALTERNATE89_ALTERNATE 605 Style00 1 Alt89FD



TOOL: INSIDE ACCESS TOOL - 891. Insert wedge between glass and weather strip directly above door lock button (see figure 1).2. Insert tool in door with tip facing the front of the vehicle (see figure 1).3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until V shaped portion of tool is beneath the window glass.5. Raise the tool until that the V shaped portion of the tool is entirely visible on the inside of the vehicle (see figure 3).6. Rotate the tool so that the tip is positioned in front of the door lock button (see figure 4).7. Pull on tool in order to slide the door lock button towards the front of the vehicle (see figure 5).NOTE: To aid in the removing of the tool, place the wedge between the glass and the weatherstrip on theinside of the door ne ar the tool. The tool will slide easily from the inside of the door.

Tool 89

_ALTERNATESG_ALTERNATE 1218 Style00 1 Altsj1

ALTERNATE

ALT

ER

NA

TE

Method - AltSJ1

_Alternate Method AltSJ1 Using the Slim Jim

TOOL: SLIM JIM1. Separate glass from weather-strips.2. Use front door.3. Move the lock pawl with tip of the Slim Jim.NOTE:Watch door lock button.

Tool SJ

ALT

ER

NA

TE

_ALTERNATESG2_ALTERNATE 1219 Style00 1 Altsj2

ALTERNATE Method - Altsj2

_Alternate Method AltSJ2 Using the Slim Jim

Tool: SLIM JIM1. BEND SLIM JIM AS SHOWN.2. Lower the tool into the door.3. Place tip NEXT TO LOCK ROD.4. Lift up on tool in order to raise the door lock button.

Tool SJ

_ALTERNATESG3_ALTERNATE 1772 Style00 1 V12501

ALTERNATE

ALT

ER

NA

TE

Method - ALT125

_Alternate MethodALT125 Using the 125 Tool

Tool:125 Tool 1.Use a strip saver and wedge to create an opening in the door between the window and the weather stripping. 2.Point tool tip towards the front of the vehicle and lower tool into door all the way to the bend in the tool 3.Turn tool handle away from the vehicle. 4.Hook and bind the door lock rod. 5.Lift tool to unlock the door

Tool 125

AC

UR

A

ACURA001ACURA 635 Style05 1 H7701F

ACURA Method - M1

Acura CL 1997 1999

Tool:771. Separate the glass from weather-stripping with a Strip Saver and Wedge.2 .With the tip of the tool facing the rear of the car, insert the tool into door, 12 inches from the door frame3. Lower the tool below the linkage shield (See Diagram for Position)4. Lift the tool so it goes in the gap between the plastic shield and the door frame. Hook the linkage5. Move the linkage forward to unlock the door.

Alternative method use Alternate Alt22

Tool 77

ACURA CL Tool in Insertion Position Tool in Working Position

View from Inside the Door Close up of Tool in Action

ACURA002ACURA 655 Style04 1 R7401

ACURA

AC

UR

A

Method - M1

Acura CL 2 Door 2001 2003

Tool: 741. Separate the glass from weather-stripping with a Strip Saver and Wedge.2. With the tip of the tool facing the rear of the car, lower tool into door.3 Lower tool deep into the door and turn the handle away from the car. Lift tool handle until working end of tool emerges from inside of the car.4. With working end of tool fully inside the car, hook door lock button with tool tip and lift to unlock the door.


Tool 74

ACURA CL Tool in Insertion Position Tool in Working Position

Hook Lock Button and Lift to Unlock

AC

UR

A

ACURA003ACURA 775 Style00 1 H9101F

ACURA Method - M1

Acura Integra 2 Door 1986 1993

Tool: Downward Hook - 911. Separate glass from weather-stripping with a wedge on passenger door.2. Point tip of tool towards front of car.3. Lower the tool into car (SEE FIG. FOR POSITION) .4. After tool is lowered, turn tool to hook bottom linkage (SEE ENLARGED ILLUSTRATION) 5. Rotate tool to bind the linkage and tilt the handle towards rear of vehicle as to move the linkage towards the front of the door.6. Watch door lock button inside of vehicle for movement. When you have bound the correct linkage, you will see the door lock button move.


Tool 91L

ACURA004ACURA 632 Style03 1 V2601

ACURA

AC

UR

A

Method - M1

Acura Integra 4 door 1986 1993 Acura Legend 2 Door 1986 1995

Acura SLX 1996 1999 Acura Vigor 1992 1994

Tool: Large side of double tool - 261. Separate glass from weather-strip.2. Lower the tool into the door near the door lock button.3. Push up on door lock button using tip of tool.NOTE:You should be watching the door lock button inside of the car. When you contact the correct lever you will see it move.


Tool 26

Acura Integra Tool in Insertion Position Tool in Working Position

AC

UR

A

ACURA005ACURA 631 Style00 1 R3501

ACURA Method - M1

Acura Integra 2 door 1994 2001

TOOL: INSIDE ACCESS TOOL - 351. Insert wedge between glass and weather strip directly above door lock button inside of vehicle (see figure 1).2. Insert tool in door with tip facing the front of the vehicle (see figure 1).3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until V shaped portion of tool is beneath the window glass.5. Raise the tool until that the V shaped portion of the tool is entirely visible on the inside of the vehicle (see figure 3).6. Rotate the tool so that the tip is positioned in front of the door lock button (see figure 4).7. Pull on tool in order to slide the door lock button towards the front of the vehicle (see figure 5).NOTE: To aid in the removing of the tool, place the wedge between the glass and the weatherstrip on the inside of the door ne ar the tool. The tool will slide easily from the inside of the door.

Alternative method use Alternate Altohj

Tool 35

ACURA009-M1ACURA 1180 Style03 1 V2609

ACURA

AC

UR

A

Method - M1

Acura MDX 2001 2006

TOOL: Large Side of Double Tool- 261.Separate glass from weather strip with Strip Saver and Wedge.2.Lower tool into the door near the door lock button.3.Turn tool handle to make contact with tool tip and lock button.4.Lift tool to unlock door.NOTE: You should be watching the door lock button inside the car. When you contact the door lock button, you will see the button move.

Tool 26

ACURA MDX Tool in Insertion Position Tool in Working Position

AC

UR

A

ACURA009-M2ACURA 1340 Style00 1 R7401

ACURA Method - M2

Acura MDX 2001 2006

Tool: 741.Separate the glass from weather-stripping with a Strip Saver and Wedge.2. With the tip of the tool facing the rear of the car, lower tool into door.3. Lower tool deep into the door and turn the handle away from the car. Lift tool handle until working end of tool emerges from inside of the car.4. With working end of tool fully inside the car, hook door lock button with tool tip and lift to unlock the door.

Tool 74

ACURA011ACURA 636 Style00 1 H4202FRD

ACURA

AC

UR

A

Method - M1

Acura RL 1997 1998

Tool: REVERSE HOOK TOOL - 421. Separate glass from weather-stripping with a wedge on REAR passenger door.2. Point tip of tool towards rear of car and insert.3. Lower tool into hole in inner door frame and beneath linkage shield. (SEE ENLARGED ILLUSTRATION) .4. Rotate tool handle towards you and raise tip of tool behind the plastic shield in order to hook and bind lock linkage.5. Watch door lock button inside of vehicle for movement. When you have bound the correct linkage, you will see the door lock button move.6. Move linkage towards front of car.


Tool 42

AC

UR

A

ACURA013ACURA 1228 Style04 1 acu016

ACURA Method - M1

Acura RSX 3 Door 2002 2006 Acura TL 4 Door 2004 2008

Acura TSX 2004 2008

TOOL: Inside Access Button Lifter- 811. Insert wedge between glass and weather-strip near the door lock button.2. Insert tool in door with tip facing the rear of the vehicle .3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until shaped portion of tool is beneath the window glass.5. Raise the tool until that the shaped portion of the tool is entirely visible on the inside of the vehicle (figure 3).6. Rotate the tool so that the tip is positioned next the door lock button and lift the button.Note : To aid in the removing of the tool, place the wedge between the glass and the weather-strip on the inside of t he door near the tool. The tool will slide easily from the inside of the door.

Rotate & Tilt ToolInto Position

1 2

3 4

Push tool againt lock buttonand lift tool to unlock door From Inside Door

Enlargement

Tool

Lock Button

Lift Tool to Unlock Door

Wedge

InsertionPosition

Lower Tool UnderGlass


Tool 81

ACURA RSX Tool in insertion position Tool in working position

View from inside the car

ACURA015-M1ACURA 778 Style05 1 H2305f

ACURA

AC

UR

A

Method - M1

Acura TL 1996 1998 Acura Integra 4 Door 1994 2001

Acura NSX 1991 2005

Tool: HORIZONTAL LINKAGE TOOL 231. Separate glass from weather-stripping with a wedge on rear passenger door .2. Point tip of tool towards rear of car.3. Lower the tool into car (SEE FIG. FOR POSITION) .4. Turn tool to hook and bind bottom linkage (SEE ENLARGED ILLUSTRATION) .5. Rock tool handle towards rear of vehicle in order to move the linkage towards the front of the car.6. Watch door lock button inside of vehicle for movement. When you have bound the correct linkage, you will see the door lock button move.

Tool 23

Acura TL Tool in insertion position Tool in working position. Rotate handle towards REAR of car

Tool must enter hole in inner door panel to grab lower linkage.

Close Up. Move linkage towards FRONT of car

AC

UR

A

ACURA015-M2ACURA 639 Style04 1 glassman

ACURA Method - M2

Acura TL 1996 1998 Acura Integra 4 Door 1994 2001

Acura NSX 1991 2005

Tool: FLEXIBLE LONG REACH TOOL - 78SG1. On driver s side door, insert tool between window and weather-stripping, tip of tool facing downward.2. Insert a wedge between tool and window and use the groove in the wedge to guide the tool into the vehicle.3. Slide the tool into the interior of the vehicle until the tip is positioned in front of the lock button.4. With the tip of the tool resting on the lock button, pull back on the tool to unlock the vehicle.Use of Glass Saver System is recommended!

Tool


Tool 78SG

Acura TL Insert SuperWedge/Glassmaninto window

Insert tool into hole created by Super-Wedge/Glassman

Hook lock button with tool, and move to rear of car to unlock

ACURA016ACURA 1514 Style03 1 V4711

ACURA

AC

UR

A

Method - M1

Acura TL 4 Door 1999 2003 Acura Legend 4 Door 1986 1995

Acura RL 4 Door 1999 2004

Tool: S Tool - 471. Separate glass from weather-strip with a wedge.2.Lower the tool below the inner door frame.3.Twist tool to hook the door lock rod.4.Lift door lock rod to unlock door.

Tool 47

ACURA TL Tool in Insertion Position Tool in Working Position

AC

UR

A

ACURA021ACURA 624 Style04 1 R8901FD

ACURA Method - M1

Acura MDX 2007 2012 Acura RDX 4 door 2007 2012

Acura RL 2005 2012

Tool: Long Inside Access Tool 891. Insert wedge between glass and weather-strip directly above door lock button inside of vehicle (see figure 1).2. Insert tool in door with tip facing the front of the vehicle3. Reposition wedge to allow the lowering of the tool into the door4. Lower tool into door until shaped portion of tool is beneath the window glass.5. Raise the tool until that the shaped portion of the tool is entirely visible on the inside of the vehicle6. Rotate the tool so that the tip is positioned under the door lock button7. Pull up on tool in order to raise the door lock button, unlocking the door.


Tool 89

Acura MDX Tool in insertion position Tool in working position

Push door lock button to unlock door

ACURA022ACURA 1606 Style06 1 jack_but

ACURA

AC

UR

A

Method - M1

Acura TL 2009 2011 Acura TL 2012 2013

Acura TSX 2009 2013 Acura TSX Sports Wagon 2011 2013

TOOL: One Hand Jack Tool- 78SG 1.Use the One Hand Jack tool to separate the door frame from the body of the vehicle. 2.Insert the Air Wedge to wards the top of the door and inflate. 3.Remove the One Hand Jack Tool . 4. Insert a Long Reach Tool into the opening. 5.Maneuver the tool to engage door lock release button. 6 Push the door lock Button Forward to Unlock the door

Button

Tool 78SG

ACURA TL Use jack Tool To make Working Room for AirjacK

Insert Airjack and Inflate

View from inside the car Button moves tward the FrontPush the door lock button forward to unlock the car

AC

UR

A

ACURA023ACURA 1725 Style00 1 startmulti

ACURA Method - M1

Acura ZDX 2010 2013

Tool- 78SG With Starter Air Jack and Regular Air jack 1. Use the Starter Air Jack to create working room between the door frame and the vehicle Body Pillar 2. Insert the Air Jack and Inflate. 3. Remove the Starter air Jack 4. Insert a Long Reach Tool into the opening. 5. Maneuver the tool to engage pull the door Handle or button to unlock the door 6 Remove the long reach tool then deflate the Air Jack 7 Pull the outside Handle to unlock the door

Tool 78SG

ALFA ROMEO001ALFA ROMEO 1515 Style00 1 LPSJ01

ALFA ROMEO

ALFA

RO

ME

O

Method - M1

Alfa Romeo All All

TOOL: SLIM JIMThese cars are equipped with a lazy pawl. You can usually open them by attacking the pawl on the door lock.These can be opened as shown in the illustrations below.


Tool SJ

AU

DI

AUDI004-M1AUDI 641 Style00 1 V2601

AUDI Method - M1

Audi 4000 1984 1989 Audi 5000 1984 1989 Audi A4 Wagon

Audi A4 Upto 1998 Audi A6 Upto 1998

Tool: Double Tool - 261. Separate glass from weather-stripping. (VERY TIGHT FIT)2. Point tool towards rear of car.3. Lower the tool into car. (SEE FIG. FOR POSITION)4. Lift tool to contact door lock knob. Lift tool to unlock door. Illustration shows passenger side door. Instructions are for either door.

Tool 26

AUDI004-M2AUDI 642 Style00 1 V5701

AUDI

AU

DI

Method - M2

Audi A4 Upto 1998 Audi A4 Wagon

Audi A6 Upto 1998 Audi A8 1998

TOOL: STRIP TOOL1. Insert Strip Savers between the window and the door or window frame.2. Insert folded end of Strip Tool in between window and Strip Saver (SEE DIAGRAM).3. Hook door lock knob with folded end of Strip Tool.4. Pull Strip Tool to unlock door.NOTE: Whenever the door lock button is exposed, we recommend using this method.

Tool 57

AU

DI

AUDI005AUDI 375 Style00 1 V8604

AUDI Method - M1

Audi S4 2000 2002 Audi 100 All Audi 200 Audi 80 All

Audi 90 All Audi A4 Sedan 1999 2001 Audi A4 Avant Wagon 1999 2001 Audi S4 Avant Wagon 2001 2002

Tool: Triple Hook Tool - 861. Insert Strip Saver and Wedge. (VERY TIGHT FIT)2. Point tip of tool towards rear of car.3. Lower the tool into car. (SEE FIG. FOR POSITION)4. Hook lock rod where it attaches to door latch mechanism and lift.5. Watch door lock button for movement. When you have hooked correct lock rod crank, you will see the door lock button move.* Illustration shows passenger side door. Instructions are for either door.

Tool 86

AUDI006AUDI 470 Style05 1 aud012

AUDI

AU

DI

Method - M1

Audi S4 2006 2012 Audi A4 Sedan 2002 2008

Audi A4 Avant 2004 2012 Audi RS-4 2006 2009

Tool: Inside Access Tool - 351. Insert wedge between glass and weather-strip directly above door lock button inside of vehicle (see figure 1).2. Insert tool in door with tip facing the front of the vehicle (see figure 1).3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until shaped portion of tool is beneath the window glass.5. Raise the tool until that the shaped portion of the tool is entirely visible on the inside of the vehicle (see figure 3).6. Rotate the tool so that the tip is positioned next to the door lock handle (see figure 4).7. Move tool to engage door lock handle, unlocking the door.Note: To aid in the removing of the tool, place the wedge between the glass and the weather-strip on the inside of the door near the tool. The tool will slide easily from the inside of the door.


REARDOOR

Wed ge

InsertionPosition

1 2

3 4

From Inside DoorEnlargement

Tool

Lock Button

Lower Tool Under Glass

Slide tool inthis directionto unlock door

Lock Button

Alternative method use Alternate Starthand

Tool 35

AUDI A4 Tool in insertion position Tool in working position

Hook the Inside Door Handle to Open View from Far Inside

AU

DI

AUDI007AUDI 1267 Style05 1 R5004

AUDI Method - M1

Audi A4 Cabriolet 2 Door 2003 2009 Audi S4 Cabriolet 2006 2001

Tool: Flexible Long Reach Tool 78SG1. Insert tool between window and weather-stripping, with tip of tool facing downward2. Insert a wedge between tool and window and use the groove in the wedge to guide the tool into the vehicle3. Slide the tool into the interior of the vehicle until the tip is positioned in front of the door lock handle.4. With the tip of the tool hook the door lock handle and pull the handle to unlock the vehicle.5.Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.

PASSENGER DOOR

Tool

Tool


Handle

Direction

Tool 78SG

Audi A4 Cabriolet Insert glassmaster tool Insert long reach tool into cavity

View from inside the vehicle Pull door handle to open door

AUDI008-M1BAUDI 1813 Style00 1 StartHand

Audi

Audi

Method - M1

Audi A6 Sedan 2011 2013

Tool- 78SG With Starter Air Jack and Regular Air jack 1. Use the Starter Air Jack to create working room between the door frame and the vehicle Body Pillar 2. Insert the Air Jack and Inflate. 3. Remove the Starter air Jack 4. Insert a Long Reach Tool into the opening. 5. Maneuver the tool to engage Pull the door Handle to unlock the door 6 Remove the long reach tool then deflate the Air Jack 7 Pull the outside Handle to Unlock the doorNote These vehicles are very delicate so the utmost care should be used

Tool 78SG

AU

DI

AUDI008b-M1AUDI 21 Style04 1 aud012

AUDI Method - M1

Audi S6 2003 2009 Audi A3 4 door 2006 2012

Audi A6 Sedan 1998 2011 Audi RS6 2004 2009

Tool: Inside Access Tool - 351. Insert wedge between glass and weather-strip directly above door lock button inside of vehicle (see figure 1).2. Insert tool in door with tip facing the front of the vehicle (see figure 1).3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until shaped portion of tool is beneath the window glass.5. Raise the tool until that the shaped portion of the tool is entirely visible on the inside of the vehicle (see figure 3).6. Rotate the tool so that the tip is positioned next to the door lock handle (see figure 4).7. Move tool to engage door lock handle, unlocking the door (see figure 5). Note: To aid in the removing of the tool, place the wedge between the gl ass and the weather-strip on the inside of the door near the tool. The tool will slide easily from the inside of the door.


REARDOOR

Wed ge

InsertionPosition

1 2

3 4

From Inside DoorEnlargement

Tool

Lock Button

Lower Tool Under Glass

Slide tool inthis directionto unlock door

Lock Button

Tool 35

AUDI A6 Tool in insertion position Tool in working position

Tool in working position

AUDI008b-M2AUDI 670 Style06 1 Jackhand

AUDI

AU

DI

Method - M2

Audi A6 Sedan 1998 2011 Audi A3 4 door 2006 2012

Audi RS6 2004 2009 Audi S6 2003 2009

TOOL: One Hand Jack Tool- 78SG1.Use the One Hand Jack tool to separate the door frame from the body of the vehicle.2.Insert the Air Wedge to wards the top of the door and inflate.3.Remove the One Hand Jack Tool .4. Insert a Long Reach Tool (such as the 78, Flat Max or Long John Tool) into the opening.5.Maneuver the tool to engage the door handle or, when available, the door lock release button.6.Pull the handle or engage the lock release button to unlock the door. Note this opening should only be used in emergency situations

Tool 78SG

Audi A6 Insert Jack Tool Insert Air Wedge

Insert tool into door cavity Pull door lock handle to unlock doorManoeuvre tool to hook door lock handle

AU

DI

AUDI009AUDI 1686 Style02 1 C2601

AUDI Method - M1

Audi A8 Sedan 2001 2003 Audi A8 Sedan 1998 Audi A8 Wagon 1998 2003

Audi A8L Sedan 2001 2006 Audi S8 Sedan 2001 2003

TOOL: LARGE SIDE OF DOUBLE TOOL- 261. Separate glass from weather-strip on REAR passenger door.2. Lower the tool into the door near the door lock button.3. Push up on door lock button using tip of tool.NOTE: USE REAR PASSENGER DOORExtreme caution should be used on this vehicle since the body is all Aluminum


Tool 26

Audi A8 Tool in working position

AUDI009bAUDI 1815 Style00 1 StartHand

Audi

Audi

Method - M1

Audi A8 Sedan 2012 2013

Tool- 78SG With Starter Air Jack and Regular Air jack 1. Use the Starter Air Jack to create working room between the door frame and the vehicle Body Pillar 2. Insert the Air Jack and Inflate. 3. Remove the Starter air Jack 4. Insert a Long Reach Tool into the opening. 5. Maneuver the tool to engage Pull the door Handle to unlock the door 6 Remove the long reach tool then deflate the Air Jack 7 Pull the outside Handle to unlock the doorCaution: This vehicle has an aluminum body and can be damaged very easily. This opening should only be used in extreme emergencies

Tool 78SG

AU

DI

AUDI009cAUDI 1776 Style00 1 Glasshdl

AUDI Method - M1

Audi A7 4 door 2011 2012

Tool: Flexible Long Reach Tool 78SG with Glassman Wedge 1. Insert Glassman Wedge to separate the door glass and pillar 2. Push the Glass man in carefully to create a gap 3. Slide the tool into the interior of the vehicle through the center of the glassman wedge until the tip is positioned in front of the door lock handle. 4. With the tip of the tool hook the door lock handle and pull the handle to unlock the vehicle. 5. Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.This opening is provided for use in extreme emergencies only, and is not recommended under for use under normal circumstances.

Tool


Pull handle

Tool 78SG

AUDI010-M1AUDI 630 Style06 1 R3510

AUDI

AU

DI

Method - M1

Audi Q7 SUV 2007 2012 Audi Allroad Wagon 1998 2005

Audi Avant 1998 2005 Audi Q5 SUV 2009 2012

Tool: Inside Access Tool-351. Insert wedge between glass and weather-strip directly above door lock button inside of vehicle (see figure 1).2. Insert tool in door with tip facing the front of the vehicle (see figure 1).3. Reposition wedge to allow the lowering of the tool into the door (see figure 2).4. Lower tool into door until shaped portion of tool is beneath the window glass.5. Raise the tool until that the shaped portion of the tool is entirely visible on the inside of the vehicle (see figure 3).6. Rotate the tool so that the tip is positioned under the door lock button (see figure 4).7. Pull up on tool in order to raise the door lock button, unlocking the door (see figure 5).Note : To aid in the removing of the tool, place the wedge between the glass and the weather-strip on the inside of the door near the tool. The tool will slide easily from the inside of the door.

Alternative method use Alternate starthand

Tool 35

Audi Q7 Tool in insertion position Tool in working position

View from inside the vehicle Pull door handle to unlock doorHook door handle with end of tool

AU

DI

AUDI010-M2AUDI 666 Style05 1 jackhand

AUDI Method - M2

Audi Q7 SUV 2007 2012 Audi AllRoad Wagon

Audi Avant Audi Q5 SUV 2009 2012

TOOL : JACK TOOL1. Insert jack tool into side of door and separate the door from the frame of the vehicle.2. Insert a ir wedge into upper portion of the door and inflate to create an opening in the door.3. Slide the tool into the interior of the vehicle until the tip is positioned in front of the lock button.4. With the tip of the tool resting on the lock button, pull back on the tool to5 Unlock the vehicle.Use of the Glass Master Wedge System Is Recommended!

Tool 78SG

Audi Q7 Insert Jack Tool and Air Wedge Inflate Air Wedge to create working space

Insert long reach tool into door Pull door handle to unlock door

AUDI011AUDI 340 Style05 1 R5004

AUDI

AU

DI

Method - M1

Audi TT Roadster 2000 2006 Audi TT 2 DOOR 2000 2012

Tool: Flexible Long Reach Tool 78SG1. Insert tool between window and weather-stripping, with tip of tool facing downward2. Insert a wedge between tool and window and use the groove in the wedge to guide the tool into the vehicle3.Slide the tool into the interior of the vehicle until the tip is positioned in front of the door lock handle.4.With the tip of the tool hook the door lock handle and pull the handle to unlock the vehicle.5.Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.

PASSENGER DOOR

Tool

Tool


Handle

Direction

Tool 78SG

Audi TT Insert Wedge in Frameless Window Insert Remote Access Tool Between Wedges

View from Inside the Door Hook Door Lock Handle and Pull Back

AU

DI

Audi012AUDI 367 Style00 1 R5004

AUDI Method - M1

Audi A5 Coupe 2008 2012 Audi R8 Copue 2008 2012

Audi S5 Copue 2008 2012

Tool: Flexible Long Reach Tool 78SG1. Insert tool between window and weather-stripping, with tip of tool facing downward2.Insert a wedge between tool and window and use the groove in the wedge to guide the tool into the vehicle3.Slide the tool into the interior of the vehicle until the tip is positioned in front of the door lock handle.4.With the tip of the tool hook the door lock handle and pull the handle to unlock the vehicle.5.Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.This opening is provided for use in extreme emergencies only, and is not recommended under for use under normal circumstances.

PASSENGER DOOR

Tool

Tool


Handle

Direction

Tool 78SG

Audi013AUDI 1707 Style00 1 R5004

AUDI

AU

DI

Method - M1

Audi 1 Series Copue 2010 2012

Tool: Flexible Long Reach Tool 78SG With Glassman Wedge 1. Insert Glassman Wedge to separate the door glass an pillar 2. Push the Glass man in carefully to create a gap 3. Slide the tool into the interior of the vehicle through the center of the glassman wedge until the tip is positioned in front of the door lock handle. 4. With the tip of the tool hook the door lock handle and pull the handle to unlock the vehicle. 5. Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.This opening is provided for use in extreme emergencies only, and is not recommended under for use under normal circumstances.

PASSENGER DOOR

Tool

Tool


Handle

Direction

Tool 78SG

AU

TOC

AR

HE

AV

Y T

RU

CK

AUTOCAR HEAVY TRUCK001AUTOCAR HEAVY TRUCK 1455 Style03 1 V8804HT

AUTOCAR HEAVY TRUCK Method - M1

Autocar All All

Tool: 102 Upward Bend Tool1.Insert the strip savers and wedge in the door to create working room to insert the tool..Insert the tool near the very rear of the front passenger side door.3.Hook the linkage directly under the door lock button where it connects to the door lock latch.4.Lift the tool to unlock the door.

Wedge

Direction

Linkage

Direction

Tool

Tool 102

All Autocar Heavy Duty Trucks. Insert the tool at rear of passenger side door.

Lower tool directly under door lock button. Lift to unlock.

BMW001BMW 523 Style05 1 78Frame

BMW

BM

W

Method - M1

BMW 325i 2006 2012 BMW 3 Series Framed Window 2000 2012 BMW 330i 2006 2012 BMW 5 Series 2001 2012 BMW 5 Series Wagon 2005 2012 BMW 550i 2005 2012

BMW 7 Series 2002 2009 BMW 745 2005 2008 BMW 760 2006 2008 BMW X3 2004 2009 BMW X5 2002 2009

Tool: 78SG Long Reach Tool with One Hand Jack and Air Jack1. Insert the One Hand Jack tool on the side of the door.2. Insert and inflate the Air Jack wedge on the top of the door.3. Prepare two (2) tools for use, the first for disabling the deadlock mechanism, the second for opening the door.4. Insert the first tool in the opening in the door .5. Maneuver the tool to push the door lock button to disable the deadlock mechanism. A clicking sound may be heard in the door. The door lock release button will be found on the dashboard or the console near the shift lever.6. With the deadlock mechanism disengaged, quickly use the long reach tool to pull the door handle twice- once to unlock the door, the second to open the door.NOTE: This opening is intended for automobiles with framed windows and deadlock mechanisms.

Dashboard

Push Door Lock Button To Release Deadlock

Tool 78SG

Use One Hand Jack t Use Air Wedge To create opening Insert Long Reach Tool at top of door

Push deadlock button on dash to release deadlock mechanism

Quickly pull door handle to unlock

BM

W

BMW006BMW 338 Style06 1 78FRLess

BMW Method - M1

BMW 645 2005 2012 BMW 3 Series Convertible 1997 2012 BMW 3 Series Coupe 2007 2012 BMW 3 Series 2008 2012 BMW 325ci 2006 2012

BMW 6 Series 2004 2012 BMW 650I 2006 2012 BMW M Coupe 2007 2010 BMW M Roadster 2007 2010 BMW M3 2000 2010

Tool: 78SG Long Reach Tool with GlassMan1. Insert the GlassMan wedge in the window.2. Prepare two (2) tools for use, the first for disabling the deadlock mechanism, the second for opening the door.3. Insert the first tool in the opening created by the GlassMan wedge.4. Maneuver the tool to push the door lock button to disable the deadlock mechanism. A clicking sound may be heard in the door. The door lock release button will be found on the dashboard or the console near the shift lever.5. With the deadlock mechanism disengaged, quickly use the long reach tool to pull the door handle twice- once to unlock the door, the second to open the door .NOTE : This opening is intended only for automobiles with frameless windows and deadlock mechanisms.Special Note: BMW is an expensive and delicate vehicle Use these openings Only in extreme emergency situations.

Tool 78SG

BMW 645 Insert Glass Master Insert Flat Tool for Door Lock Button

Push Door Lock Button on Console Pull Door Handle TWICE to UnlockInsert SQM Tool for Door Handle

BMW009BMW 825 Style00 1 V5701

BMW

BM

W

Method - M1

BMW 8 Series Upto 1998

Tool: STRIP TOOL - 571. Insert Strip Saver in between window and door, or window frame.2. Insert folded end of Strip Tool between Strip Saver and the door or window frame (SEE INSERTION DIAGRAM).3. Maneuver Strip tool to hook door lock knob.4. Pull Strip Tool to unlock door.NOTE : All 1991 and later model BMWs are equipped with a special lock mechanism which engages when the door is locked with the key. When the door is locked with the key it, is impossible to open with car opening tools. In the event of lost keys, BMW dealers can get replacements with the V.I.N. number. If the car is locked by any oF their method, use these opening methods. NOTE : Since most of the time vehicle will be in a dead lock position; we recommend ordering a replace-ment key from the BMW dealer. This key can be ordered using the vehicle identification number.

Tool 57

BM

W

BMW010BMW 114 Style04 1 V8802

BMW Method - M1

BMW M Coupe 1998 2002 BMW 5 series upto 2000 BMW 6 Series upto 2003

BMW 7 Series 4 door 1989 2001 BMW M Roadster 1998 2002 BMW M3 Coupe Upto 1999

Tool: Double Bend Tool 881. Use inside door handle of rear door as guide (See figure for position).2. Separate glass from weather-strips.3. Lower the tool into the door.4. Tip of tool must go into the hole in doorframe.5. Lift up on tool and hook bell crank (see fig.).NOTE: You should be watching the door lock button inside of the car. When you contact the correct bell crank, you will see the door lock button move.NOTE: All 1991 and later model BMWs are equipped with a special lock mechanism which engages when the door is locked with the key. When the door is locked with the key, it is impossible to open with car opening tools. In the event of lost keys, BMW dealers can get replacements with the V.I.N number. If the car is locked by any other method, use these opening methods.NOTE: Since most of the time vehicle will be in a dead lock position; we recommend ordering a replacement key from the BMW dealer. This key can be ordered using the vehicle identification number.NOTE: Handle on the tool may be different than shown in photo.

V8802.eps


Tool 88-45

BMW Tool in insertion position Tool in working position

BMW013BMW 1190 Style00 1 R5004

BMW

BM

W

Method - M1

BMW Z3 1997 2002 BMW Z4 2003 2009

BMW Z8 All

Tool: Flexible Long Reach Tool 78sg1. On driver s side door, insert tool between window and weather-stripping, with tip of tool facing down-ward (see figure 1 for position).2. Insert a wedge between tool and window and use the groove in the wedge to guide the tool into the vehicle (see figure 2).3. Slide the tool into the interior of the vehicle until the tip is positioned in front of the lock button (see figure 4. With the tip of the tool resting on the lock button, pull back on the tool to unlock the vehicle (see figure 5. Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.

PASSENGER DOOR

Tool

Tool


Handle

Direction

Tool 78SG

CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

CHEVROLET HEAVY TRUCKS001CHEVROLET HEAVY TRUCKS 1456 Style04 1 R103-04

CHEVROLET HEAVY TRUCKS Method - M1

Chevrolet HT C Series Vertical Buttons and Vent Win-dows Pre 1989

Tool: Vent Window Tools 103 & 1041) Insert the Flat vent tool 104 directly under the vent window handle.2) Insert the Vent window tool 1033) Depress the vent window handle release button with the flat 104 Tool.4) Rotate the vent window handle with the 103 tool while maintaining therelease button depressed.5) Insert your arm in through the open vent window to unlock the truck.

Insert #104 Latch Button Tool

Insert #103 Vent Handle

Tool 103-04

Chevrolet Medium Duty Trucks. Vent Windows and Vertical Buttons.

Insert Flat Vent tool under the vent window directly below the vent window latch handle.

Depress vent window latch lock button with flat tool while turning handle with other tool.

Keep the Button depresed while turn-ing the handle.

CHEVROLET HEAVY TRUCKS002CHEVROLET HEAVY TRUCKS 1457 Style04 1 H2337F

CHEVROLET HEAVY TRUCKS

CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

Method - M1

Chevrolet HT C Series Horizontal Linkage 1989 2002

Tool: HORIZONTAL LINKAGE TOOL 231. Point the tip of the tool towards the rear of the car.2. Insert the tool between the glass and weather-strip.3. Lower the tool into the door slowly while turning tool until handle is pointing away from car.4. Stop lowering tool when you feel it contact the door lock rod.5. While watching door lock lever (inside car), twist tool so as to move tip of tool towards front of car.NOTE: Watch the door lock button inside the car. If you contact the correct rod inside the door, you will see the door lock button move. Illustration shows passenger side door. Instructions will work on either front door. Door lock lever (circled) is shown reversed. FOR 1997 Models: See Index

Tool 23

Chevrolet Kodiack heavy duty truck Lower the tool into the door at the very rear edge of the passenger door

Tool in working position. Hook top linkage.

View from inside the door. Move link-age forward to unlock.

CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

CHEVROLET HEAVY TRUCKS003CHEVROLET HEAVY TRUCKS 330 Style06 1 H9101FHT


Chevrolet HT 4500 Horizontal Linkage 2003 2012 Chevrolet HT 5500 Horizontal Linkage 2003 2009

Chevrolet HT C Series Horizontal Linkage 2003 2009

Tool: 9 1 Downward Hook Tool1.Insert the strip savers and wedge in the door to create working room. Insert the tool into the rear of the door.2. Lower the tool with the tip facing the rear INSIDE of the door. Note that the tip of the tool must not go behind the window run channel so keep the tip facing towards the inside while you lower it in the door.3.Hook the door lock rod with the tip of the tool.4.Rotate the tool in order to move the linkage to the front of the car.

Wedge

Gap In Shield

Move Tool

Shield

Gap In Shield

Move Tool

ENLARGEMENT

Tool 91

All C Series 2003 and later Medium and Heavy duty Truck Chassis

Tool in insertion position Tool in working position. Note tool is deep in door with tip at rear corner

Twist tool to move linkage to front of vehicle

Close up of tool in action.View inside door. Tool hooks linkage at lower rear corner of door.

CHEVROLET HEAVY TRUCKS004CHEVROLET HEAVY TRUCKS 1459 Style04 1 H9101FHT


CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

Method - M1

Chevrolet HT Van Cab All

Tool: 91 Downward Hook Tool1 Insert the strip savers and wedge in the door to create working room. Insert the tool into the center of the door.2.Lower the tool on to the door lock linkage.3.Hook the door lock rod with the tip of the tool4.Rotate the tool in order to move the linkage to the front of the car.

Wedge

Gap In Shield

Move Tool

Shield

Gap In Shield

Move Tool

ENLARGEMENT

Tool 91

Chevrolet heavy duty van chassis is used with a variety of deifferent bed configurations

Insert the number 106 tool near the center of the door.

Lower the tool on top of the lock link-age. Twist the tool so the tip moves towards the front of the door.

When you have hooked the correct linkage you will see the door lock but-ton move up

CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

CHEVROLET HEAVY TRUCKS005-M1CHEVROLET HEAVY TRUCKS 1460 Style03 1 v4715HT


Chevrolet HT W Series Light Duty Pre 1995

TOOL: S Tool - 471.Separate the glass from weather-stripping on door.2.Lower tool into door in between the inner door frame.3.Twist tool to hook the door lock rod.4.Lift door lock rod to unlock door.Reminder: Be sure to use the rubber tip on your 47 Tool

Wedge

PullUp

LinkagePullUp

Tool 47

Chevrolet light duty cab over business class trucks

Tool in insertion position Tool in working position. Tool is only a few inches into the door.

CHEVROLET HEAVY TRUCKS005-M2CHEVROLET HEAVY TRUCKS 1461 Style02 1 V2612HT


CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

Method - M2

Chevrolet HT W Series Light Duty Pre 1995


Wedge

PullUp

LinkagePullUp

Tool 26

Tool in insertion position Lift the tool up under the door lock button, to unlock the door.

CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

CHEVROLET HEAVY TRUCKS006CHEVROLET HEAVY TRUCKS 1462 Style04 1 V2613HT


Chevrolet HT W Series Light Duty 1996 2009


Wedge

PullUp

LinkagePullUp

Tool 26

Chevrolet W3500 and W4500 Lower tool into the door near the door lock button.

Lower tool below door lock button, lift tool under button to unlock.

View of the door lock button from the inside of the vehicle.

CHEVROLET HEAVY TRUCKS007CHEVROLET HEAVY TRUCKS 1468 Style05 1 H2340HT


CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

Method - M1

Chevrolet HT T Series Medium Duty Pre 1995

Tool: 23 Horizontal Linkage Tool1. Insert the strip savers and wedge in the door to create working room. Insert the tool near the rear of the door.2.Lower the tool into the door until the tool rests on the lock linkage.3.Twist the tool to bind the linkage.4.Move the tip of the tool forward so the linkage moves towards the front of the truck.5.Watch the door lock button for movement. The door lock button will move up when the vehicle is unlocked.

Direction

Wedge

Direction

Enlargement

Tool 23

Chevrolet Medium Duty T Series trucks

Insert tool between glass and weather stripping.


Hook top linkage with tool tip. Move linkage to rear to unlock.

Close up of tool in action

CH

EV

RO

LET

HE

AV

Y T

RU

CK

S

CHEVROLET HEAVY TRUCKS008CHEVROLET HEAVY TRUCKS 1463 Style06 1 V10501HT


Chevrolet HT T Series Medium Duty 1996 2006

Tool: 105 Tool1 Insert the strip savers and wedge in the door to create working room. Insert the tool near the rear of the door.2.Lower the tool into the door about of the way down in the door.3.Point the tip of the tool towards the rear of the truck.4.Lift the tool under the door lock linkage.5.Watch the door lock button for movement. The door lock button will move up when the vehicle is unlocked.

Direction

Wedge

Tool

Direction

Tool 105

Chevrolet large and medium duty busi-ness class cab over trucks

Tool in insertion position. Tool in working position.

View from inside the door. View of door with panel.Hook tool tip under lock linkage and lift to unlock.

CHRYSLER002CHRYSLER 1429 Style05 1 V4707

Chrysler Dodge Plymouth Eagle

Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Magnum 2005 2008 Chrysler 300C 2005 2013 Chrysler 300C SRT 2005 2013 Chrysler 300M 1999 2004

Chrysler Aspen 2007 2009 Chrysler Cirrus 4 door 1995 2000 Chrysler Concorde 1998 2004

TOOL: S Tool - 471. Separate the glass from weather-stripping on door.2. Lower tool into door in between the inner door frame.3. Twist tool to hook the door lock rod.4. Lift door lock rod to unlock door.Reminder: Be sure to use the rubber tip on your 47 Tool

Tool 47

Dodge Magnum Tool in Insertion Position Tool in Working Position

View from Inside the Door Hook Lock Rod and Lift to Unlock.

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER002b-M1CHRYSLER 1789 Style05 1 V12501

Chrysler Dodge Plymouth Eagle Method - M1

Chrysler 200 2011 2013 Chrysler 200 Convertible 2011 2013

Tool:125 Tool 1.Use a strip saver and wedge to create an opening in the door between the window and the weather stripping. 2.Point tool tip towards the front of the vehicle and lower tool into door all the way to the bend in the tool 3.Turn tool handle away from the vehicle. 4.Hook and bind the door lock rod. 5.Lift tool to unlock the door

Tool 125

Chrysler 200 Tool In Working Position inside of door

close up of inside of door tool hooking linkage

CHRYSLER002b-M2CHRYSLER 1827 Style04 1 H6603RD


Chrysler D

odge Plym

outh Eagle

Method - M2

Chrysler 200 2011 2013

TOOL: Checkmark Tool- 661. Insert a strip saver and wedge into the rear passenger door between the glass and the weather stripping. 2.Point the tip of the tool towards the front of the vehicle and lower the tool into the door. Do not lower the tool very far into the door. 3.Turn the tool handle away from the vehicle to access the lock linkage. 4.Lift the tool to hook the lock linkage from below (see diagram). 5.Turn tool handle to move lock linkage towards the rear of the vehicle to unlock the door.

Tool 66

Chrysler 200 Tool insertion Position Tool in working position


Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER006CHRYSLER 563 Style04 1 R5009dd


Chrysler Crossfire Convertible 2005 2008 Chrysler Crossfire Coupe 2004 2008

Chrysler Crossfire SRT 6 2005 2006 Chrysler Crossfire Roadster 2005 2008

Tool: Flexible Long Reach Tool 78sg1. Insert tool between window and weather-stripping, with tip of tool facing downward2. I nsert a wedge between tool and window and use the groove in the wedge to guide the tool into the vehicle3. Slide the tool into the interior of the vehicle until the tip is positioned in front of the door lock handle.4. With the tip of the tool hook the door lock handle and pull the handle to unlock the vehicle.5. Pulling the Inside Door Handle once unlocks the door. You must pull the Outside Door Handle to open the door.Note: Use of the Glass Master System is recommended!

Drivers DOOR ONLY

Tool

Tool


Handle

Direction

Drivers DOOR ONLY

Tool 78SG

Chrysler Crossfire Tool in Insertion Position Hook Door Handle.

Pull Door Handle to Open.

CHRYSLER009-M1CHRYSLER 535 Style00 1 V2201


Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Ram 3500 Series 2002 2002 Chrysler Fifth Avenue 1985 1989 Chrysler Fifth Avenue 1990 1993 Chrysler Imperial 1986 1989 Chrysler Imperial 1990 1993 Chrysler New Yorker 1986 1989 Chrysler New Yorker 1990 1993

Chrysler New Yorker Salon 1990 1993 Dodge Ram Truck 1994 2001 Dodge Ram 2500 Series 2002 2002 Dodge Truck Full Size 1994 2001 Plymouth Colt Pop up locks 1986 1994 Plymouth Colt Vista Pop up locks 1986 1994

Tool: SMALL HOOK TOOL 221. Separate glass from weather-stripping with a wedge.2. Point tip of tool towards rear of car.3. Lower the tool into car (SEE FIG. FOR POSITION) .4. Hook Bell Crank with end of tool.5. Lift straight up on tool in order to raise the lock button.


INSER TION

Front PassengerDoor

Tool 22

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER009-M2CHRYSLER 799 Style00 1 V2601


Plymouth Colt Pop up locks 1986 1994 Dodge Colt Pop up locks 1986 1994 Dodge Colt Pop up locks 1986 1994 Dodge Colt Vista Pop up locks 1986 1994

Dodge Colt Vista Pop up locks 1986 1994 Dodge Ram Van 1985 1997 Dodge Van Full Size 1985 1997 Plymouth Colt Vista Pop up locks 1986 1994

Tool: DOUBLE TOOL - 26For the above vehicles equipped with pop-up style locks1. Insert tool between glass and weather-strip parallel with the door lock button.2. Lower the tool into the door.3. Place tip of tool under the door lock button.4. Lift up on tool in order to raise the door lock button.

Tool 26

CHRYSLER010CHRYSLER 704 Style00 1 H2332F


Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler Laser 1984 1989 Chrysler LeBaron 2 Door 1982 1989 Chrysler LeBaron 4 Door 1982 1989 Chrysler Maserati TC 1989 1991 Chrysler Town & Country 1984 1990 Chrysler Town & Country Wagon Wagon 1984 1988 Dodge 600 1984 1988 Dodge Aries 1984 1988 Dodge Caravan 1984 1990

Dodge Charger 1984 1990 Dodge Daytona 1984 1990 Dodge Lancer 1984 1989 Dodge Shelby Charger 1984 1990 Plymouth Caravelle 1984 1986 Plymouth Laser 1984 1989 Plymouth Reliant 1984 1988 Plymouth Voyager 1984 1990

Tool: HORIZONTAL LINKAGE - 231. Separate glass from weather-stripping with a wedge.2. Point tip of tool towards front of car.3. Lower the tool into car (SEE FIG. FOR POSITION) .4. After tool is lowered, turn tool to hook top linkage (SEE ENLARGED ILLUSTRATION) .5. Rotate tool to bind the linkage and tilt the handle towards rear of vehicle as to move the linkage towards the rear of the door.6. Watch door lock button inside of vehicle for movement. When you have bound the correct linkage, you will see the door lock button move.

Tool 23

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER011CHRYSLER 694 Style00 1 HSJ01


Chrysler Fifth Avenue 1980 1985 Chrysler Imperial 1980 1985

Chrysler New Yorker 1980 1985

Tool: SLIM JIMThis vehicle is equipped with a lazy pawl lock mechanism, and it can be opened as shown in the illustra-tion below.


Tool SJ



Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler LeBaron 1990 1995 Chrysler LeBaron Convertible 1990 1995 Chrysler LeBaron GTC Convertible 1990 1995

Dodge Daytona 1990 1994 Dodge Monaco 1990 1992 Plymouth Grand Fury 1990 1991

Tool: DOUBLE TOOL - 261. at the lock button inside of the vehicle.2. a wedge between the glass and the weather-strip near the lock button.3. the tool between the glass and the weather-stripping in front door.4. the tool into the door.5. the back side of the lock button with the tip of the tool and lift it up.6. the lock button for movement. NOTE: When you contact the correct lever on door lock mechanism, you will see the door lock button move.

Tool 26

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER014CHRYSLER 697 Style04 1 V4704F


Chrysler LHS 1994 2001 Chrysler Concorde 1993 1997 Chrysler New Yorker 1994 1995 Dodge Intrepid 1993 1997 Dodge Intrepid 1993 2006

Dodge Intrepid 1998 2004 Dodge Stratus 4 Door 1995 2006 Eagle Vision 1993 1997 Plymouth Breeze 1996 2000

Tool :S Tool 471. Separate glass from weather-stripping with a wedge.2. Point tip of tool towards rear of car.3. Lower the tool into car (see figure for position).4. Hook linkage that runs from door lock pawl to door latch mechanism (see enlargement diagram below).5. Pull straight up on tool to unlock door.

Tool 47

Chrysler LHS Tool in working position View from inside the door

Close up of tool on linkage

CHRYSLER015CHRYSLER 1366 Style06 1 RLJ02


Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler Pacifica Wagon 2004 2008

TOOL : FLEXIBLE LONG REACH TOOL - 78SG1. Insert strip saver and wedge on the upper corner of the door.2. Insert an Air Wedge into the door and inflate.3. Remove the wedge from the door.4. Insert tool into the door.5. Maneuver the tool so that the tip of the tool accesses the door lock button.6. Push the door lock button to unlock the door. Use of the Glass Master Wedge System Is Recommended!

Tool 78SG

Chrysler Pacifica Insert Wedge on Top Corner of Door. Insert Air Wedge.

Pump Air Wedge to Inflate. Push Door Lock Button With Tool to Unlock Door.

Insert Tool Directly Above Air Wedge.

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER016CHRYSLER 784 Style05 1 H2218FRD


Chrysler Prowler 2001 2002 Plymouth Prowler 1999 2000

Tool: Horizontal Linkage Tool - 231. Separate glass from weather-stripping with a wedge.2. Point tip of tool towards rear of car.3. Lower the tool into car (see figure for position).4. Hook lock linkage with hooked end of tool.5. Turn tool handle towards rear of vehicle to unlock the door.

Alternative method use Alternate AltGM

Tool


Tool 23

Chrysler Prowler Tool in Insertion Position Tool in Working Position

View from Inside the Door Close Up



Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler PT Cruiser 4 Door 2001 2011 Chrysler PT Cruiser Convertible 2005 2008

Tool: S Tool - 471. Insert Strip Saver and Wedge into passenger side front door to create an opening for the tool.2. Lower the S tool into the door directly above the door handle.3. Once lowered into the door, twist tool to hook door lock rod (See Photos 4 and 5)4. Lift tool to unlock the door.

Tool 47

Chrysler PT Cruiser Tool in Insertion Position Tool in Working Position

View from Inside the Door Close up of Tool Hooking Lock Rod

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER018CHRYSLER 1290 Style04 1 H2354B


Chrysler Sebring 1995 2000 Dodge Avenger 1995 2000

Tool: HORIZONTAL LINKAGE TOOL - 23 1. Separate glass from weather-stripping with a wedge.2. Point tip of tool towards front of car.3. Lower the tool into car (SEE FIG. FOR POSITION) .4. After tool is lowered, turn tool to hook top linkage (SEE ENLARGED ILLUSTRATION) . 5. Rotate tool to bind the linkage and tilt the handle towards rear of vehicle as to move the linkage towards the rear of the door. 6. Watch door lock button inside of vehicle for movement. When you have bound the correct linkage, you will see the door lock button move.

Tool 23

Tool in insertion position Tool in working position View from inside the door

Move linkage to rear of car

CHRYSLER019CHRYSLER 1182 Style04 1 H9128F


Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler Sebring Convertible 1996 2000

Tool: DOWNWARD BEND TOOL- 911 Insert Strip Saver and Wedge in passenger side door to create an opening for the tool.2 Use the curved end of the tool, and point it towards the front of the car. Lower the tool approximately half way into the door, directly above the door handle (see diagram for position).3 Twist tool handle to enable the working end of the tool to access the lock linkage.4 Hook and bind lock linkage, and turn tool handle towards rear of car in order to move the linkage forward and un-lock the door. NOTE: Handle on the tool may be different than shown in photo.

Tool 91L

CHRYSLER SEBRING CONVERT-IBLE

Tool in working position View from inside the door

Close up of tool in action

Chr

ysle

r D

odge

Ply

mou

th E

agle



Chrysler Sebring 4 Door 2001 2006 Dodge Avenger 2008 2010

Dodge Charger 2006 2010

TOOL S TOOL - 471. Insert a wedge to separate the glass from the weather strip on passenger side door. 2. L ower tool into the car door directly above the door handle. 3. Twist tool handle in order to hook the lock rod. Once the tool makes contact with the rod, you should see the door lock button move. 4. Lift tool to move lock rod and unlock the door.

Tool 47

CHRYSLER SEBRING Tool in Insertion Position Tool in Working Position


CHRYSLER020bCHRYSLER 1193 Style04 1 R5007


Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler Sebring Convertible 2001 2006 Chrysler Sebring Coupe 2001 2006

Dodge Stratus Coupe 2001 2006 Dodge Stratus RT 2002 2006

TOOL : FLEXIBLE LONG REACH TOOL - 78SG1. Use appropriate wedge (like the Glass Master Wedge System) to separate the glass and create working room.2. Insert the tool into the vehicle.3. Move the door lock button to with the tool to unlock the door.Use of the Glass Master Wedge System Is Recommended!

Tool 78SG

Chrysler Sebring Insert Super Wedge and Tool in Open-ing

Reach Tool Across Door to Access Door Handle

Pull Door Handle to Unlock Door

Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER020cCHRYSLER 1829 Style05 1 V4708


Dodge Charger 2011 2013 Dodge Avenger 2010 2013

TOOL: S Tool - 471. Separate the glass from weather-stripping on door.2. Lower tool into door in between the inner door frame.3. Twist tool to hook the door lock rod.4. Lift door lock rod to unlock door.

Tool 47

Dodge Charger Tool in insertion position. Tool in working position.

Inside of door Tool hooking linkage

CHRYSLER022CHRYSLER 1297 Style05 1 v4708


Chrysler D

odge Plym

outh Eagle

Method - M1

Chrysler Town & Country 1991 2007 Chrysler Voyager 2001 2003 Dodge Caravan 1991 2007

Dodge Grand Caravan 1991 2007 Plymouth Voyager 1991 2000

TOOL: S Tool- 471. Insert Strip Saver and Wedge into the passenger side front door.2. With tip facing rear of vehicle, lower the tool into the door directly above the door handle.3. Twist tool to hook lock linkage.4. Lift tool to unlock door.

Tool 47

CHRYSLER TOWN & COUNTRY Tool in Insertion Position Tool in Working Position


Chr

ysle

r D

odge

Ply

mou

th E

agle

CHRYSLER023CHRYSLER 767 Style06 1 H6603RD


Chrysler Sebring 2007 2012 Chrysler Sebring Convrtiblr 2007 2012

TOOL: Checkmark Tool- 661. Insert a strip saver and wedge into the rear passenger door between the glass and the weather stripping. 2.Point the tip of the tool towards the front of the vehicle and lower the tool into the door. Do not lower the tool very far into the door. 3.Turn the tool handle away from the vehicle to access the lock linkage. 4.Lift the tool to hook the lock linkage from below (see diagram). 5.Turn tool handle to move lock linkage towards the rear of the vehicle to unlock the door.

Alternative method use Alternate alt47

INSER TION

Front PassengerDoor

Tool 66

Chrysler Sebring Tool in insertion position. Use rear door.

Tool in working position.

Tool shown in working location. Close up of tool in action. Hook lock rod and lift to unlock.

View from inside the door. Note loca-tion of door lock rod.

Chrysler025CHRYSLER 1593 Style03 1 V4707


Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Grand Caravan 2008 2012 Chrysler Town & Country 2008 2012

TOOL - 471. Insert a wedge to separate the glass from the weather strip on passenger side door.2. L ower tool into the car door directly above the door handle.3. Twist tool handle in order to hook the lock rod. Once the tool makes contact with the rod, you should see the door lock button move.4. Lift tool to move lock rod and unlock the door.

Tool 47

Dodge Caravan Tool in insertion position. Tool in working position.

Chr

ysle

r D

odge

Ply

mou

th E

agle



Dodge Challenger 2 Door 2009 2013

TOOL: 1051.Create an opening in the door using a strip saver and wedge.2.Point the tip of the tool towards the front of the vehicle and lower the tool into the door.3.Turn tool handle away from vehicle to allow tool tip to access lock linkage.4.Lift tool to engage lock linkage and unlock door.

Alternative method use Alternate AltGMV

Linkage

Tool 105

Dodge Chalenger Tool 105 Tool in Working Position

Closeup of tool lifting Linkage Tool Under linkage Lift

DODGE009CHRYSLER 703 Style04 1 H2351F


Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Colt Horizontal 1986 1994 Dodge Colt Vista Horizontal 1986 1994 Eagle Summit 2 Door 1989 1992

Plymouth Colt Horizontal 1986 1994 Plymouth Colt Vista Horizontal 1986 1994

Tool: HORIZONTAL LINKAGE TOOL - 231. Separate glass from weather-stripping with a wedge.2. Point tip of tool towards rear of car.3. Lower the tool into car (SEE FIG. FOR POSITION) .4. After tool is lowered, turn tool to hook top linkage. (SEE ENLARGED ILLUSTRATION) .5. Rotate tool to bind the linkage and tilt the handle towards rear of vehicle as to move the linkage towards the front of the door.6. Watch door lock button inside of vehicle for movement. When you have bound the correct linkage, you will see the door lock button move.

Tool 23

Tool in insertion position Tool in working position Inside the door

Inside the door close-up

Chr

ysle

r D

odge

Ply

mou

th E

agle

DODGE017CHRYSLER 933 Style00 1 V4704F


Dodge Dakota 1997 2000


Tool 47



Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Dakota 2001 2004 Dodge Durango 2001 2003

Tool: Horizontal Linkage Tool - 231. Insert Strip Saver between window and weather strip of the front passenger side door.2. With the tool facing the front of the vehicle, lower tool into he door, directly above the door handle.3. Hook and bind the lower linkage (see diagram and photos for position).4. Move linkage towards FRONT of the vehicle to unlock the door.

Tool 23

DODGE DAKOTA Tool in Insertion Position Tool in Working Position


Chr

ysle

r D

odge

Ply

mou

th E

agle

DODGE019CHRYSLER 1158 Style05 1 V4701


Dodge Durango 2004 2008 Dodge Dakota 2005 2012

Dodge Durango 1998 2000


Tool 47

Dodge Durango Tool in Insertion Position Tool in Working Position

Tool in Working Position View from Inside the Door

DODGE019bCHRYSLER 1830 Style05 1 V4708


Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Durango SUV 2011 2013

TOOL: S Tool - 471. Separate the glass from weather-stripping on door.2. Lower tool into door in between the inner door frame.3. Twist tool to hook the door lock rod.4. Lift door lock rod to unlock door.

Tool 47

Dodge Durango Tool in insertion position. Tool in working position.

Inside of door tool hooking linkage

Chr

ysle

r D

odge

Ply

mou

th E

agle



Dodge Neon 2 door 1994 1999 Plymouth Neon 2 door 1994 1999

Tool: Horizontal Linkage Tool 231. Separate glass from weather-strip.2. Lower the tool into the door on top of lock linkage.3. Twist tool to bind linkage.4. Move tool forward.

Tool 23

DODGE NEON Tool in insertion position Tool in working position

Inside of door panel off. Close-up of inside panel off.

DODGE026CHRYSLER 832 Style03 1 H8206RD


Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Neon 4 door 1994 1999 Plymouth Neon 4 door 1994 1999

Tool: Drop & Rock - 82 Use REAR DOOR1. Separate the glass from the weather-strip of the rear door with strip saver and wedge.2. Point the tip of the tool towards the front of the vehicle.3. Insert the tool into the door near the back of the door.4. Lower the tool below the lock linkage5. Turn the tool so the tip moves towards the inside6. Lift the tool and rock it so the tip moves towards the front of the vehicle.

Tool 82


Chr

ysle

r D

odge

Ply

mou

th E

agle

DODGE027CHRYSLER 1145 Style04 1 H2357


Dodge Neon 4 door 2000 2005 Dodge Neon RT 4door 2002 2003

Dodge Neon SRT-4 2004 2005

Tool: Horizontal Linkage Tool- 231. Point tip of tool towards front of car.2. Using door lock button inside car as guide. Insert tool between glass and weather-strip.3. Hook door lock rod just behind door lock button.4. Gently push down and forward on tool. (Care should be taken since the plastic linkage inside may come loose.)NOTE: When you contact the correct lever on door lock mechanism, you will see the door lock button move.

Tool 23


Close-up

DODGE028CHRYSLER 1353 Style00 1 R103-04


Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Ram Truck 1979 1993 Dodge Truck Full Size 1979 1993

Tool: Vent Window Tools 103 & 1041) Insert the Flat vent tool 104 directly under the vent window handle.2) Insert the Vent window tool 1033) Depress the vent window handle release button with the flat 104 Tool.4) Rotate the vent window handle with the 103 tool while maintaining the release button depressed.5) Insert your arm in through the open vent window to unlock the truck.

Insert #104 Latch Button Tool

Insert #103 Vent Handle

Tool 103-04

Chr

ysle

r D

odge

Ply

mou

th E

agle



Dodge Ram 3500 Series 2002 2002 Dodge Ram Truck 1994 2001

Dodge Ram 2500 Series 2002 2002 Dodge Truck Full Size 1994 2001

Tool : Large side of double tool - 261. Separate glass from weather-strip.2. Lower the tool into the door near the door lock button.3. Push up on door lock button using tip of tool.NOTE:You should be watching the door lock button inside of the car. When you contact the correct lever,you will see the door lock button move.

Tool 26

Dodge Ram 1500 Tool in insertion position. Tool in working position.

View from inside the door



Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Ram 2500, 3500 2004 2008 Dodge Ram 1500 2002 2008

Dodge Ram Power Wagon 2004 2005 Dodge Ram SRT 2004 2009

TOOL: S Tool - 471. Separate glass from weather-strip ( Very tight fit, be very gentle ) .2. Point tip of tool towards front of car.3. Lower tool into the door.4. Twist tool handle to hook and bind lock linkage (see fig.).5. Pull up on tool while hooking door lock rod.NOTE: You should be watching the door lock button inside of the car. When you contact the correct rod, you will see the door lock button move.Instructions are for passenger side door.

Tool 47

DODGE RAM Tool in insertion position Tool in working position

Inside view of Tool in working position Close Up

Chr

ysle

r D

odge

Ply

mou

th E

agle

DODGE031CHRYSLER 1138 Style05 1 H4708


Dodge Ram Van 1998 2003

Tool: S Tool - 471. Separate glass from weather-strip with a wedge.2. Use the tool to find your insertion position. Mark your position with the wedge and insert your tool.3. Lower the tool below the inner door frame.4. Twist tool to hook the door lock rod.5. Lift door lock rod to unlock door. Reminder: Be sure to use the rubber tip on your 1847NC Tool.

Linkage

Tool 47

DODGE RAM 2500 99 Tool and wedge in insertion position Tool and wedge in working position

View from inside the door Close up of tool and linkage



Chrysler D

odge Plym

outh Eagle

Method - M1

Dodge Spirit 1989 1995 Dodge Dakota 1988 1996 Dodge Diplomat 1982 1989 Dodge Dynasty 1988 1993 Dodge Omni 1983 1990 Dodge Ram Van 1985 1997 Dodge Shadow 1984 1994 Dodge Van Full Size 1985 1997 Eagle Medallion

Eagle Premier 1988 1992 Eagle Summit 4 DOOR 1989 1992 Eagle Summit Wagon 4 DOOR 1989 1992 Plymouth Acclaim 1989 1995 Plymouth Duster 1984 1994 Plymouth Horizon 1983 1990 Plymouth Sundance 1984 1994 Plymouth Van Full Size 1985 1997

Tool: DOUBLE TOOL - 261. Insert tool between glass and weather-strip parallel with t

Documents

Access Tools 2011-12 Car Opening Manual