AC10 Rust Remover Solutionsfrontweb - Competitive Choice · RUST REMOVER AND METAL PREP AC-10 DIRECTIONS FOR BRUSH OR SPRAY RUST REMOVAL FROM STEEL SURFACES (SEE DILUTIONS CHART)

RUST REMOVER AND METAL PREPAC-10

AERO-GREEN AC-10 RUST REMOVER AND METAL PREP is a concentrated, water-reducible phosphoric acid and detergent blend specially formulated to both thoroughly clean and profile steel, galvanized metals, zinc, concrete and masonry/brick surfaces before applying a coating, stain or sealer. Depending on the surface to be cleaned, this clear, odorless, innovative product can be diluted with water and brushed on, sprayed on, or used in cold or heated dip tanks for impressive results.

Non-flammable, non-combustible, and non-hazardous, state-of-the-art Aero-Green AC-10 Rust Remover and Metal Prep can be utilized in areas with limited ventilation.

Safe to use, environmentally friendly, yet more than strong enough to get the job done, Aero-Green AC-10 is the only rust remover and metal prep you’ll ever need.

AERO-GREEN AC-10 RUST REMOVER AND METAL PREP WAS DEVELOPED FOR USE ON:STEEL: Removes rust and flash rust from steel surfaces and leaves a corrosion inhibiting residue which prevents rusting and aids in coating adhesion.

GALVANIZED METALS: Improves adhesion by removing the passivation film on the surface.

CONCRETE: Cleans and degreases concrete surfaces to prepare the surface for paint, sealer or other coatings. Aero-Green AC-10 reduces preparation time by eliminating the separate pre-cleaning and rinsing operation before acid etching on concrete.

MASONRY/BRICK: Cleans mortar joints, removes excess mortar and easily rinses with water to eliminate any residue from surface without causing any harm to the surrounding vegetation.

Hi-Lite Solutions, Inc.1285 Brucetown RoadP.O. Box 399Clear Brook, VA 22624

www.Hi-LiteSolutions.com

P. 540.450.8375 F. 540.450.8379

Environmentally Preferred Specialty Cleaners

WWW.HI-LITESOLUTIONS.COM


Environmentally Preferred Specialty Cleaners

RUST REMOVER AND METAL PREPAC-10

DIRECTIONS FOR BRUSH OR SPRAY RUST REMOVAL FROM STEEL SURFACES(SEE DILUTIONS CHART)1) Add concentrate to water and mix. If available, hot water will accelerate cleaning and etching.

2) Brush or spray solution onto steel surfaces.

3) Allow 1-10 minutes contact time.

4) Rinse surface with hot water.

5) Heavily rusted parts may require scrubbing while rinsing.6) Dry surface immediately by wiping with a clean, dry cloth.

SAFETY/CAUTIONThis product is a phosphoric acid based cleaner and is corrosive. It must be used with all plastic hand pumps, tank-type sprayers, plastic-lined dip tanks, pressure washers with an acid injector system, plastic pails and acid resistant brushes. Read the MSDS before use; follow all precautions especially those regarding personal protection. Rubber gloves are recommended to prevent irritation and drying of the skin. Goggles are recommended to protect the eyes.

Harmful if swallowed. If ingested, drink large amounts of water and seek medical attention. Avoid getting into eyes. If contact occurs, flush with running water. If eye irritation persists get medical attention. May cause irritation of skin in prolonged use without gloves. If skin is irritated, wash hands in cold water and apply a hand lotion. If irritation persists, seek medical attention.

DILUTIONS FOR BRUSH OR SPRAY RUST REMOVAL FROM STEEL SURFACES

Light: 10%................................... (12 oz/gal)Medium: 15% ............................. (20 oz/gal)Heavy: 25% ................................ (42 oz/gal)

SOILS DILUTIONS

DIRECTIONS FOR USE IN A COLD OR HEATED DIP TANK1) For cold dip tank: Fill bath with 1 part water to 1 part Aero-Green AC-10 Rust Remover & Metal Prep.

2) For heated dip tank: Fill the bath with 10 parts water to 1 part Aero-Green AC-10 Rust Remover & Metal Prep.

3) Immerse steel items to be de-rusted into solution.

4) Allow items to remain in solution 5-20 minutes.

5) Check at 5 minute intervals to determine if the rust is removed.

6) Heavily rusted parts may require scrubbing during the 5 minute inspections to remove the top layer of rust. This will reduce the amount of time parts are in the immersion tanks.

7) Rinse surface with hot or cold water.

8) Dry surface immediately by wiping with a clean dry cloth or using forced air.


Directions for use in Español and Françaisavailable online at:www.Hi-LiteSolutions.com/instructions© 2011 Hi-Lite Solutions, Inc. All Rights Reserved.

0 00


Documents

AC10 Rust Remover Solutionsfrontweb - Competitive Choice · RUST REMOVER AND METAL PREP AC-10 DIRECTIONS FOR BRUSH OR SPRAY RUST REMOVAL FROM STEEL SURFACES (SEE DILUTIONS CHART)