9
ANSI American National Standards Institute ASME American Society of Mechanical Eng. ASTM American Society of Testing Materials AGA American Gas Association API American Petroleum Institute ASSY Assembly ABS Absolute (plastic pipe) ATM Atmosphere AVG Average AUX Auxiliary BC Bolt Circle BB Bolted Bonnet BLDG Building B&S Bell and Spigot BWG Birmingham Wire Gauge BBL Barrel BBE Beveled Both End BLE Beveled Large End BSE Beveled Small End BLK Black BE Beveled End BF Blind Flange, Bottom Flat BOP Bottom Of Pipe BTU British Thermal Units Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas... 1 of 9 5/18/2015 12:51 PM

Abbreviations for Piping

Embed Size (px)

DESCRIPTION

Piping Termininology

Citation preview

  • ANSI American National Standards Institute

    ASME American Society of Mechanical Eng.

    ASTM American Society of Testing Materials

    AGA American Gas Association

    API American Petroleum Institute

    ASSY Assembly

    ABS Absolute (plastic pipe)ATM Atmosphere

    AVG Average

    AUX Auxiliary

    BC Bolt Circle

    BB Bolted Bonnet

    BLDG Building

    B&S Bell and Spigot

    BWG Birmingham Wire Gauge

    BBL Barrel

    BBE Beveled Both End

    BLE Beveled Large End

    BSE Beveled Small End

    BLK Black

    BE Beveled End

    BF Blind Flange, Bottom Flat

    BOP Bottom Of Pipe

    BTU British Thermal Units

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    1 of 9 5/18/2015 12:51 PM

  • BW Butt Weld

    BM Bill of Material, Brass Mounted, BenchMark

    CB Catch Basin

    CFM Cubic Feet per Minute

    CI Cast Iron

    CS Cast Steel, Carbon Steel, Cold SpringCountersink

    C/W Complete With

    CU Cubic

    CFH Cubic Feet per Hour

    CFD Cubic Feet per Day

    COND Condensate

    CORK Corrosion

    COORD Coordinate

    CP Close Pattern

    C to C Centre to Centre

    CONC Concentric

    CONT Continue

    CO Clean Out

    CPLG Coupling

    CSA Canadian Standards Assoc.

    CSC Car Seal Closed

    CSO Car Seal Open

    DWG Drawing

    DBL Double

    DEG Degree

    DIAG Diagram

    DF Drain Funnel

    DO Ditto

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    2 of 9 5/18/2015 12:51 PM

  • DS Double Sweep, Dummy Support

    DIM Dimension

    DISCH Discharge

    C Celsius, Centigrade, Hundred

    EFW Electronic Fusion Weld

    ERW Elec. Resistance Weld

    EA Each

    ELL Elbow

    ECC Eccentric

    ELEV Elevation

    E to E End to End

    EST Estimate

    EH Extra Heavy

    F Fahrenheit

    FAB Fabricated

    FE Flanged end, Flow Element

    FF Flat Face, Full Faced, Flange Face

    F to F Face to Face

    FLG Flange

    FOB Flat on Bottom, Freight on Board

    FOF Face of Flange

    FOT Flat on Top

    FS Forged Steel

    FW Field Weld

    FTG Fitting, Footing

    FIG Figure

    FS Forged Steel, Far side

    FT Foot, Feet

    GAL Gallon

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    3 of 9 5/18/2015 12:51 PM

  • GALV Galvanized

    GND Ground

    GPM Gallons per Minute

    GPH Gallons per Hour

    GR Grade

    HEX Hexagon

    HR Hour

    HDR Header

    HC Hydrocarbon

    HP High point, High Pressure

    IE Invert Elevation

    ID Inside Diameter

    IMP Imperial

    IPS Iron Pipe Size, Inches per Second

    I Structural I Section

    IS Inside Screw

    ISO Isometric Drawing

    INS Insulate

    INST Instrument

    IB Iron Body

    INCL Including

    INFO Information

    JT Joint

    kPA Kilopascals

    LB Pound

    LT Light Wall

    LR Long Radius

    LC Lock Closed

    LO Lock Open

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    4 of 9 5/18/2015 12:51 PM

  • LH Left Hand

    LW Lap Weld

    LE Large End

    LG Long

    LP Low Point, Low Pressure

    LIN Lineal

    M Meter, Million, Thousand, (Metric) (Roman)MK Mark

    MATL Material

    MAWP Maximum Allowable Working Pressure

    MAX Maximum

    MB Machine Bolt

    MFG Manufacture

    MH Manhole

    MI Malleable Iron

    L Materials List

    MIN Minimum, Minute

    MISC Miscellaneous

    MK Mark

    MRGL Metal Reinforced Graphite Laminate

    MSS Manufacturers Standardization Society

    MTO Material Take-off

    MW Miter Welder

    NA Not Applicable

    NC Normally Closed

    NO Normally Open, Number

    NPS Nominal Pipe Size

    NPT National Pipe Thread

    NRS Non-rising Stem

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    5 of 9 5/18/2015 12:51 PM

  • NO or # Number

    SO Slip-on

    IS&Y Inside screw & Yoke

    NOM Nominal

    NTS Not to Scale

    NS Near Side

    OA On Centres

    OD Outside Diameter

    OS& Y Outside Screw & Yoke

    P&ID Piping & Instrumentation Diagram

    PBE Plain Both Ends

    PE Plain End

    PI Pressure Indicator

    POE Plain One End

    PS Pipe Support, Pressure Switch

    PF Plain Face

    PSIA Pounds per Square inch Absolute

    PSIG Pounds per Square Inch Gauge

    PVC Polyvinyl Chloride

    PR Pair

    QO Quick OpeningQTY QuantityRED Reducing, Reducer

    RF Raised Face

    RJ Ring Joint

    RTJ Ring Type Joint

    RR Railroad

    RPM Revolutions Per Minute

    RS Rising Stem

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    6 of 9 5/18/2015 12:51 PM

  • REINF Reinforce

    R Radius

    REF Reference

    REQD RequiredRH Right Hand

    SAE Society of Automotive Engineers

    SCR Screwed

    SCH or SCHED Schedule

    SEC Second

    SECT Section

    SF Spot Faced

    SKT Socket

    S to S Seam to Seam

    SMLS Seamless

    S.O.L. Sock-o-let

    SPEC Specification

    SQ SquareSR Short Radius

    SS Stainless Steel

    ST Steam Trap

    STA Station

    STD Standard

    STL Steel

    STM Steam

    STR Straight

    SUCT Suction

    SW Socket Welding

    SWG Swage

    SWP Steam Working Pressure

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    7 of 9 5/18/2015 12:51 PM

  • SYM Symmetrical

    SYS System

    T,TEMP Temperature

    T&C Thread and Coupled

    T-T Tangent to Tangent

    TBE Threaded Both Ends

    TC Test Connection

    TE Threaded End

    TF Top Flat

    TGT Tangent

    THK Thick

    TMP To Match Pipe

    TOC Top of Concrete

    TOE Threaded One End

    T.O.L. Thread-o-let

    TOS Top Of Steel

    TPI Threads Per Inch

    TSE Threaded Small End

    TSS Temporary Suction Strainer

    TYP Typical

    T&G Tongue and Groove

    UG Underground

    UNC Unified Coarse Thread

    UNF Unified Fine Thread

    VAC Vacuum

    VERT Vertical

    WB Welded Bonnet

    WE Welded End

    WF Wide Flange Structural

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    8 of 9 5/18/2015 12:51 PM

  • WN Welding Neck

    WOG Water, Oil and Gas

    W.O.L. Weld-o-let

    W/O Without

    WP Working Pressure

    WT Weight, Wall Thickness

    XH Extra Heavy

    XS Extra Strong

    XXH Double Extra Heavy

    XXS Double Extra Strong

    Abbreviations for Piping Termininology flashcards | Quizlet https://quizlet.com/8359909/abbreviations-for-piping-termininology-flas...

    9 of 9 5/18/2015 12:51 PM