ANNEXURE VI
ANNEXURE VI
CONTENTS OF THE REPORT1. Cover page (Light Green) on hard
paper2. Inner page same as cover page but on the soft paper3.
Declaration
4. Acknowledgment (if any)
5. Contents
Summary Introduction
Work
IndustryANNEXURE VIIINDUSTRIAL PROJECT REPORT(For Project
Semester 2015)
for
(Name of Student)
Roll No.Under the Guidance of
(Name of Faculty Coordinator
Name of Industry Coordinator
with Designation)
with Designation)
Department of Electronics and Communication Engineering
THAPAR UNIVERSITY-PATIALAJune 2015
ANNEXURE VIII
DECLARATION
I hereby declare that the project work entitled ( Title of the
Project) is an authentic record of my own work carried out at
(Place of work) as requirement of project semester for the award of
degree of B.E. (Electronics & Communication Engineering) at
Thapar University Patiala, Under the Guidance of ( Name of the
Industry Coordinator) and (Name of Faculty Coordinator), during
Even Semester starting from January 2015.(Signature of student)
(Name of the student)
(Roll No.)
Date:__________________
Certified that the above statement made by the student is
correct to the best of our knowledge and belief.
(Name & Designation)
(Name & Designation)
Faculty Coordinator
Industry CoordinatorIndustry Name: ANNEXURE IX
THAPAR UNIVERSITY, PATIALA
Department of Electronics & Communication Engineering
PROJECT SEMESTER Session 2015
FEEDBACK FROM INDUSTRY ON PROJECT SEMESTER
1. Were the students serious about their work?
ABC
2. Has the work done by the student been of value to the
Yes / NoCompany?
3. Did the students have adequate background knowledge?ABC4. Did
the students have adequate maturity and adjustability?ABC5. Do you
think that the Institute can interact with the
Yes / No Industry /organization in some other way also?
Please specify (Ignore if not applicable).
6. How do you rate the student overall?
ABC7. Would you like to take Thapar University students again
next year? Yes / No (Please find request-letter for arranging some
Training-slots for next year too- ANNEXURE XI)AExcellent
B Good
CFair
Industry Coordinator Signature__________
Name:____________ Designation:________ Mobile:_________
Email:___________
Students Name: ANNEXURE X
Roll No.:
THAPAR UNIVERSITY, PATIALA
Department of Electronics & Communication Engineering
PROJECT SEMESTER Session 2015STUDENT FEED BACK FORM
1. Name and Place of the Industry:
______________________________________
2. Are you satisfied with the manner the department did
your:
(i) Placement in various industrial units
Satisfied
Unsatisfied
(ii) Registration & Orientation
Satisfied
Unsatisfied
(iii) Evaluation
Satisfied
Unsatisfied
If not satisfied, please give your suggestions overleaf.
3.Was the technical assistance /guidance received from the
Institute satisfactory? If not, identify the area where assistance
was lacking?
_________________________________________________________________
_________________________________________________________________
SingleNo. of Project
4.Were you given a single project or number of similar
projects?
5. Specify below areas of the projects carried out by you
Analysis & Design/Fabrication/R& D/Supervision/..
6. What additional subjects did you study in order to
successfully complete the projects in the industry?
PROJECTSUBJECT
YES NO
7.Problem faced in the industry with regards to:
i) Project identification
ii) Problem analysis
iii) Implementation of the Project
iv) Acceptance in industry
v) Recognition of the work done by you
8. Has the Project Semester proved to be an exercise that has
enhanced your
IPersonal Attributed at work:
YES NO
i) Communication Skills
ii) Confidence level
iii) Creativity
iv) Planning
v) Adaptability
vi) Being methodical
vii) Organizational skills
IITechnical Aspects
i) Knowledge
ii) Skill at work9.Were you provide following
i) Stipend
ii) Accommodation
iii) Conveyance
10. Any additional information /suggestion for further
improvement of the project:
_______________________________________________________________________________
_______________________________________________________________________________
_______________________________________________________________________________
A-Excellent
B-Good
C- Fair
ANNEXURE X
No.-TU/ECED/IAP15/SR
Dated: 24th April 2015
Sub: Slots request for Project Semester of B.E. Final Year
(Electronics & Communication Engineering) students of Thapar
University, Patiala to be started from January 2016.Dear Sir,
As part of course-curriculum of the Bachelor of Engineering
(B.E.) E&C degree final year students are required to undergo a
project semester training (of one semester duration) in Industry,
Research Laboratories or Private/Government organizations in India
or abroad.
The present final year engineering students of Electronics &
Communication Engineering are required to undergo this project work
for one full semester starting from January 2016. We shall feel
obliged, if you could kindly allot a few slots for B.E. Final Year
(Electronics & Communication Engineering) students in your
esteemed organization. Kindly intimate us whether your company can
offer stipend or not.
We look forward to your early & favorable reply.
With warm regards.
Thanking you,
Dr. Mukesh Kumar,Assistant Professor & IAP Coordinator
Department of Electronics & Communication Engineering
Thapar University, Patiala-147004, Punjab
Email: [email protected];
Contact Numbers: +91-175-2393334; +91-175 - 2393083
