A New & Improved Charge Controller Based on the 555 Chip

A simple charge controller for solar and wind systems

UPDATE This 555 based solar charge controller project has won first place in the Utility Category of the 555 Design Contest!!!!! Scroll to the bottom of the page for more information on the contest.

Several years ago I began building my own wind turbines and solar panels to provide power on my remote, off-grid property. A charge

controller is an essential part of any wind or solar system to ensure the batteries aren't over or under charged. The charge controller monitors the battery voltage and switches the batteries off charge when they are fully charged, and switches them back on charge when they reach a pre-set level of discharge. This is a new and improved charge controller design based on the 555 chip.

When I originally posted my home-built wind turbine, solar panel and charge controller designs on the web,

NE555P Timer IC

12 VDC Automotive Relay SPDT 30/40A

12 VDC 5-Pin Relay Socket

they became wildly popular. Lots of people all over the world have built their own versions. I get flooded with emails every day from people with comments or questions. A very large percentage of the emails concern problems people are having building the original charge controller design. While the design is certainly more advanced than some middle school lesson plans in shop class, it's certainly do-able for any reasonably skilled person.

The original charge controller design is still working after years of field use. Lots of people all over the world have built copies of it. The original story of the development of this charge controller can be found on my wind turbine page.

Problem is, people with less electronics experience had trouble building it and getting it to work. The circuit was rather complex and confusing for electronics beginners. Some people in far-flung parts of the world were having problems finding all the necessary parts. The daily flood of emails requesting help with building the charge controller have prompted me to redesign it.

So I set myself the goal of greatly simplifying my solar/wind charge controller circuit. I wanted to get it down to only one IC if possible, and reduce the number of other components as much as possible. I also wanted to make sure it only contained easy to find components that should be obtainable pretty

Stinger SGJ28 Terminal Strip

8 Ohm 200W Non-Inductive Dummy

Load Resistor

Extech EX330 Autoranging Mini

Multimeter

7805 +5V Voltage Regulator TO-220

UPG D5722 Sealed Lead Acid Batteries

much anywhere in the world. That way maybe more people would be able to build it without running into problems.One of my friends suggested I switch to using one of the popular microcontroller chips and replace all the analog circuitry with one chip. That would certainly get the parts count way down. However, I was worried that the microcontrollers would be too expensive or difficult to obtain in some parts of the world, and too difficult for non-technical people to program. I decided to stick with analog circuitry for now, though the microcontroller option is a possibility for the future.

Here is the schematic of my original charge controller circuit. The heart of the charge controller circuit consists of a voltage

divider, two comparators, and an S-R flip flop. My original idea was to redesign it using the LM339 Quad Comparator IC. I'd need two of the comparators for this circuit, and could make an S-R flip-flop using the other two left over comparators on the chip. I played around with this idea for a while, and even bread-

IRF540 MOSFET N-CH 100V 33A TO-

220AB

Perforated PC Board 3-3/16" x 2-

1/2"

100AH Solar Wind Power Backup

Battery"

Battery Cutoff Switch

Click on a lady

to learn how

to meet her.

boarded a few test circuits. I was having some trouble getting it to work right though. So I shelved the project for a while and worked on other things.

One other project I as working on was a PWM motor speed controller for the pump I use with my recirculating sluice box that I use for gold

prospecting. The speed controller uses a 555 timer chip. While looking at a diagram of the internal structure of the 555 chip, I was struck by how closely it resembles my original charge controller circuit. Suddenly I realized I could redesign the charge controller circuit using the 555 chip and greatly simplify the circuit and reduce the part count.

Compare the two diagrams on the left to see the similarities between my original charge controller circuit and the innards of the NE555 timer chip. The colored boxes represent similar sections. The 555 timer could replace 7 components in the original circuit, and reduce the total complexity of the circuit

I set to work. In only a very short time, I had a working prototype circuit bread-boarded. It worked right the first try,

which is rare for me. I almost always make some sort

of bone-head mistake wiring things up.

Here is a schematic of the new charge controller circuit. Click on it for a larger, clearer version.

I was careful to use only easy to find parts. The NE555 is probably the most popular IC in history. Billions of them are made every year. It should be easy to find just about anywhere in the world. I also switched to a 5 Volt regulator from the 8 Volt regulator the earlier version used. People were complaining they couldn't find it. The transistor is a 2N2222, NTE123, 2N3904, or other similar general purpose

small NPN transistor. The MOSFET is an IRF540 or similar power MOSFET. I just happen to have a bunch of IRF540s on hand, left over from other projects. So I used one of them rather than buying something else. Use whatever you can find.

All the resistors are 1/8 watt. 1/4 watt or higher resistors can be substituted if you don't have 1/8 Watt resistors. The two trimpots, R1 and R2, should ideally be multi-turn units, but ordinary single-turn units can be substituted, with a slight loss of precision in the tuning. I used 10K trimpots because I already had them on hand. Any value between 10K and 100K ought to work just fine. 10% tolerance is plenty good enough on all the passive components. There is no need for any precision parts in this circuit.

The relay is a general purpose SPDT automotive relay rated at 40 amps. It should be very easy to find. Get one from an auto parts store, or salvage one from a junked car in a scrap yard. I

have included a pinout for the relay for ease of connection. 40 Amps may seem like overkill, but it allows for expansion in the future. You may start with only one small solar panel, then add a few more later, possibly a wind turbine, and a bigger battery bank. Eventually the charge controller will need to switch some serious current. Why not build in the capability from day one? All other parts are specified below.

Most of the parts can be purchased at your local Radio Shack. The rest of the parts can be found at auto parts stores, and online electronics suppliers like Digi-Key, Newark, etc. You might find the online suppliers to be much cheaper, especially if you plan on building several units and need multiples of each part. You could also try looking for deals on parts on Amazon.com. I buy my automotive relays on Ebay. Even with shipping it is cheaper than the auto parts store, and they are delivered right to my mail box.

IC1 - 7805 5 Volt positive Voltage Regulator

IC2 - NE555 Timer Chip

PB1, PB2 - NO Momentary Contact Push Buttons

LED1 - Green LED

LED2 - Yellow LED

RLY1 - 40 Amp SPDT Automotive RelayD1 - 1N4001 or similarR1, R2 - 10K Multi-Turn Trim-PotsOnce I had the prototype working on the

breadboard, I built another unit on a piece of Radio Shack Protoboard for use in the field. It came together in only a couple of hours, and again, worked the first time (I must be living right lately). This more rugged version will get mounted in a box and given a thorough testing in the field.

Note that on this board I have chosen to use the 78L05 version of the 5 Volt regulator. It is in a tiny TO-92 package, the same size as the 2N2222 transistor. It is the small, black rectangle on the upper left corner of the board. It saves a lot of board space. It can only handle 100 mA, but that is plenty enough to power this circuit. If you can't find the little 78L05, you can use the full size TO-220 version of the 7805, which is much more common. There will be no penalty other than using up a little more board real estate. I just happened to have a few of the 78L05s left over from another project.

Once you have the circuit built, it is time to tune or calibrate it. I use 11.9V and 14.9V as my low and high set points for the controller. These are the points where it switches from sending power to the batteries to dumping power into a dummy load, and vice versa (a dummy load is only needed if you are using a wind turbine, if using only solar panels, the dummy load line can be left open).Probably the best way to tune the circuit is to attach a variable DC power supply to the battery terminals. Set the power supply to 11.9V. Measure the voltage at

Test Point 1. Adjust R1 until the voltage at the test point is as close to 1.667V as you can get it. Now set your variable power supply to 14.9V and measure the voltage at Test Point 2. Adjust R2 until the voltage at the test point is as close to 3.333V as you can get it.Test the operation of the charge controller by running the input voltage up and down between about 11.7 and 15.1 Volts. You should hear the relay pull in at about 14.9 Volts and open at about 11.9 Volts. In between the two set points the controller should stay in whichever state it is in. The Charge and Dump buttons can be used to change the state of the controller when the input Voltage is between the two set points.Before you write to me and tell me that my lower set point is too low and I am over-discharging my batteries, consider that the battery voltage isn't

normally going to get that low except under load. If the load were removed, the voltage would recover over time back up to well over

12V. So the batteries aren't as deeply discharged as

you might think at first glance.Once I had the circuit working, I mounted it inside a semi-weatherproof enclosure. The relay is on the left side. I used a barrier strip

to make wiring everything together easier. I used heavy gage wire for all the high-current connections. This thing was designed to switch up to 40 Amps after all. I also included a fuse in line with the solar/wind input line.

Click on the image for a larger view.

Here is another view with the lid in place. I used this enclosure because I happened to already have it on hand, not because it is the best

one for the job. For permanent outdoor use I would prefer to use a more rugged and weather-proof enclosure like I did for my original charge controller design. However, I like the fact that I can see the LEDs through the translucent lid and tell which state the charge controller is in at a glance, and I didn't

have to drill any extra holes in the box for the LEDs. This box will work for field testing purposes.

Click on the image for a

larger view.

Here is a side view of the unit showing the feed-through barrier strip with all the connections to the outside. There are connections

for the positive side of the battery(s), the positive input from a solar panel or wind turbine, the positive side of an optional dummy load, and three ground connections.

When hooking up the charge controller, the battery should be connected first. That way the electronics will have a stable source of power. If a solar panel or wind turbine is connected first, the controller is liable to wildly oscillate between states.

I should explain about dummy loads. The type of wind turbines I build have no real provision for braking or furling in high winds. It is only the presence of a constant load on them that prevents them from over-reving in high winds. So when the charge controller senses that the batteries are fully charged and

switches them out of the circuit, it switches in a dummy load (just a big external bank of high-wattage resistors) to soak up the power output of the wind turbine and keep it under load. If you are using a commercially made wind turbine with built-in over-rev protection, or using only solar panels, then the dummy load isn't necessary and you can leave the dummy line unconnected. You can learn more about dummy loads on my wind turbine page.

Here is another side view showing the charge and dump buttons. The charge controller will automatically switch between charge and dump when the battery voltage reaches the low and high set points. Between the set points the controller will

remain in whichever state it is in. These buttons allow me to manually toggle the charge controller between the two states.

Here is a photo of the first real field test of the new charge controller design. It seemed to be working good in my bench tests, but I wanted

to make sure it worked right under real-world conditions. So I set up one of my home-made 60 Watt solar panels outside my workshop and used it to

charge up a deep-cycle battery using the new charge controller. It worked great. The charge controller let power run into the

battery until it was fully charged and then switched to dumping power so as not to over-charge the battery. Perfect!

Click on the photo for a larger version.

Here is a closer photo of the setup. The battery is a 36 AH deep-cycle unit often used in personal mobility scooters and motorized

wheel chairs. I find that they work well in small-scale wind and solar power systems. The Volt meter is showing 12.64 volts on the battery, which is essentially fully charged. The battery was nearly fully charged when I started this test. It took only a short time for the solar panel to top it off and the charge controller to switch over to dumping. A highly successful test.

The only issue I had during the test was seeing which of the LEDs was on in the bright sunlight. In normal use though the charge controller would be mounted in a sheltered and shady spot out of the direct sunlight.

Click on the photo for a larger version.

Here is a brief video I shot during the test run. It shows how the charge controller automatically switches over from charging to dumping when the upper set point is reached.

Multiple solar panels and/or wind turbines can be connected to this unit. All the power sources can be connected in

parallel and fed into the single input connection. Each individual solar panel or wind turbine needs to have its own blocking diode though. Here is a diagram of a typical system with a wind turbine and two solar panels feeding the charge controller. Typically an AC inverter is included in the system to power AC loads. Click on the image for a larger version.

People write me and ask why they need a charge controller and batteries? Why not just connect the solar panel or wind turbine directly to the inverter and be done with it? Well, the answer is that the sun doesn't always shine and the wind doesn't always

blow, but people want power anytime. The batteries store power when it is available, for use when it is needed.

I may develop a printed circuit board for this project, if time permits and there is sufficient interest. I'll post further updates on this project as it progresses.

UPDATEMy friend Jason Markham has created a PC Board layout for this project almost as soon as I posted it.

Click the PCB to go to his web site.

UPDATEPeople are writing me and asking if this charge controller can be used with 24 Volt systems, and what changes would be necessary. The circuit should work fine for 24 Volt systems. The relay will need to be replaced with one rated for 24V coil voltage, and the pots will have to be re-calibrated for new high and low set points for the higher battery voltage. The 7805 voltage regulator is rated for up to 35 Volts input voltage, so no other changes in the circuit should be

necessary.UPDATEIn an effort to create a compact, neat and portable solar power system, I have mounted the charge

controller on top of a battery box. I have also mounted an AC inverter on the box. This is a much larger and higher capacity battery than I was using in my early tests of the charge controller. The inverter and charge controller are mounted on the battery box with industrial strength, sticky-back Velcro.

Here is another view of the setup. As you can see, I have also included a cigarette lighter style plug for powering 12V DC

loads. It is a complete solar power system in one

small (but heavy) package. All I have to do is connect a solar panel or two to it. I can't wait to try it out on my next camping trip. I'll have plenty of power in the wilderness.

I have finally decided to ditch my old battery bank, which I had been lugging around on my wilderness outings for years. It was

a bank of 14 smaller 12V AGM batteries. I got the batteries essentially for free, so I wired them in parallel, put them in a plastic bin, and used them with my portable solar/wind power system. The setup was very heavy and unwieldy. I kept telling myself I'd get rid of it and go with one big battery once the little batteries started dying. They hung on for years and years. I must have been treating them right. Finally they started loosing capacity and dying off one by one. So I went out and bought one big battery to replace them all. It is about the same size and weight as a car battery, but it is a deep-cycle design, perfect for solar/wind systems. It has about the same AH capacity as the old bank of 14, but is much smaller and quite a bit lighter. It only set me back about $200.

If it lasts as many years as the old bank, I'll be very happy. My back will also be happy that I don't have to lift the old bank of 14 batteries anymore.

UPDATEThis 555 based solar charge controller project has won first place in the Utility Category of the 555 Design Contest!!!!! Yahooooo!

For anyone interested, here is a Youtube video of Chris Gammell and Jeri Ellsworth announcing the 555 contest winners. The bit where they talk this project at about the 47 minute mark.