97-1 Relay panel, fuse panel CAUTION! Disconnect the battery Ground (GND) strap before working on the electrical system. Notes: Before disconnecting the battery, determine the correct coding for the anti-theft radio. After reconnecting the battery, check and activate the vehicle's electrical equipment (radio, clock, comfort and convenience features, etc.) as outlined in this Repair Manual or the Owner's Manual. Page 1 of 5 Relay panel, fuse panel 11/20/2002 http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.EE01.97.1

97-1 Relay panel, fuse panel.pdf

Download PDF Report

Upload
mefisto06c
View
20
Download
6

Embed Size (px)

Citation preview

97-1

Relay panel, fuse panel CAUTION!

Disconnect the battery Ground (GND) strap before working on the electrical system.

Notes:

Before disconnecting the battery, determine the correct coding for the anti-theft radio.

After reconnecting the battery, check and activate the vehicle's electrical equipment (radio, clock, comfort and convenience features, etc.) as outlined in this Repair Manual or the Owner's Manual.

Page 1 of 5Relay panel, fuse panel

11/20/2002http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.EE01.97.1
97-2

Fuse panel, removing and installing

- Carefully pry off side cover from instrument panel.

- Remove both mounting bolts -B- (2 Nm or 18 in. lb), then depress tabs -C- and remove fuse panel -A- toward rear.

Page 2 of 5Relay panel, fuse panel

11/20/2002http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.EE01.97.1
97-3

Central electric unit and relay panel, removing and installing

Note:

The relay panel is only required for certain optional equipment, and is not standard equipment.

- Remove driver's-side knee bar.

Repair Manual, Body Interior, Repair Group 68

- Remove both mounting bolts -C- (2 Nm or 18 in. lb) and disconnect all screw connections -D- and -E- if necessary.

- Pull out relays and control modules and then unclip relevant relay panel.

- Remove central electric unit -B- and relay panel -A-from bottom.

Page 3 of 5Relay panel, fuse panel

11/20/2002http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.EE01.97.1
97-4

Electronics box (E-box) in plenum chamber, removing and installing

- Remove mounting bolts (arrows) and pull off cover.

- When installing, press cover on by hand and tighten mounting bolts in diagonal sequence. Tightening torque: 4 Nm (35 in. lb) (also see information on cover).

- Remove engine control module and, if necessary, remove auxiliary relay panel/auxiliary fuse panel Page 97-5 .

- Disconnect harness connector at connector station.

- Pull out engine wiring harness together with rubber grommet from opening in electronics box.

Note the following when installing:

- Remove both nuts -A- (4 Nm or 35 in. lb).

- Lift electronics box off studs at rear and pull out of mount -B-.

- Install in reverse order of removal.

- Always replace seal -C-: seal must not overlap opening in body and edge of sheet metal.

Page 4 of 5Relay panel, fuse panel

11/20/2002http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.EE01.97.1
97-5

Auxiliary relay panel/auxiliary fuse panel, removing and installing

Location: in footwell, bottom left.

- Remove nut -A- (2 Nm or 18 in. lb) and self-tapping screw -B-.

- Remove relay and control module, unclip relay carrier and, if necessary, unclip auxiliary relay panel.

- Pull out auxiliary relay panel from retainers and remove from below.

- Install in reverse order of removal.

Page 5 of 5Relay panel, fuse panel

11/20/2002http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.EE01.97.1