Upload
seriousguy2
View
220
Download
0
Embed Size (px)
Citation preview
8/3/2019 964-965 page
1/2
Door/locksDoor, internal
964 Rittal Catalogue 32/System accessories
B
7.4
Door,internal
Support stripsFor attachment of Cable trunking Cable conduit holders Contact hazard protection covers Equipment installed on the door Cable clamping and attachment
4.5 mm diameter hole on a 25 mm DIN pitchpattern.
Material:Sheet steel, zinc-plated, passivated
Supply includes:Packs of 20,including screws.
Accessories:
Screws and self-tapping screws M5,see page 1011.
For TS, CM, ES, TP For door widthmm
Lengthmm
Model No. SZ
400 290 4594.000
500 390 4309.000
600 490 4596.000
800 690 4598.000
900 790 4579.000
1000 890 4599.000
For AE For enclosures AE Model No. SZ
1007.5002),1018.5002),1050.5001),1100.500,1114.5001),1213.5001),
1013.5002)1019.5002)1057.5001110.5001130.5001350.5001)
2325.000
1009.5002),1012.5002),1054.500,1060.500,1090.500,1339.500,1376.500
1010.5002)1039.5001058.5001076.5001260.5001)1360.500
2326.000
1014.5002),1077.500
1073.5002327.000
1016.5002)
,1055.500,1280.5001)
1017.5002)
1180.500 2328.000
1) For these AE models, the door rails should be cutto length.
2) Only in conjunction with perforated mounting strips(see page 965).
SpacersThe universal assembly component for all caseswhere a distance from the mounting level isrequired. With self-tapping thread for diameter4.5 mm. The following components may beattached to the rear using 5.5 x 13 mm screws:
Top-hat/cross rails Contact hazard protection covers Master switch trim panels Cable clamp rails,
etc.
Material:Hexagonal steel (SW8)
Surface finish:Zinc-plated, passivated
Accessories:
Screws 5.5 x 13 mm,see page 1011.
50
25
Lengthmm
Packs of Model No. TS
25 12 2311.225
50 12 2311.250
8/3/2019 964-965 page
2/2
Door, internal
Door/locks
965Rittal Catalogue 32/System accessories
B
7.4
Door,internal
Perforated mounting stripFor AE stainless steel, AP universal console1)For vertical mounting on the threaded bolts of thedoor, for attaching Support strips for AE, see page 964. Door stay SZ 2519.000,
see page 967.
3.7 mm diameter hole on a 25 mm DIN pitchpattern.
Material:Sheet steel, zinc-plated, passivated
Supply includes:Packs of 20,including nuts and serrated washers.
Accessories:
Screws,see page 1011.
To match AELength
mmModel No. SZ
1005.500, 1005.600,1006.500, 1006.600,1009.600
318 2310.0381)
1012.600, 1014.600 698 2310.0761016.600, 1018.600 938 2310.100
1017.600, 1019.500,1019.600
1138 2310.120
1) For door at top.
Utility lecternFor programming units etc. Prepared for mount-ing on the tubular door frame of TS, CM, ES, PC oron any sufficiently large surface.When required for servicing, it folds down quicklywith a maximum support area, and after use isstowed between the tubular door frames in aspace-saving design.Load capacity: max. 30 kg.
Material:Sheet steel
Colour:RAL 7035
Support area For doorwidthmm
Model No. TSWidthmm
Depthmm
413 400 600 4638.600
613 400 800 4638.800
Wiring plan lecternHolds wiring plans during fault finding and main-tenance work.The wiring plan lecterns can be bayed accordingto the door width.For mounting on the tubular door frame.
Material:Utility lectern: PolypropyleneMounting bracket: Die-cast zinc
Colour:Similar to RAL 7035
Supply includes:Wiring plan lectern (width 210 mm).Assembly parts.
For enclosures Packs of Model No. TS
TS, CM, ES, PC, TP 1 4120.000
For door widthmm
Required/possible numberof wiring plan lecterns
min. max.
400 1 1
500 1 1
600 2 2
800 2 3
1000 3 3
CD/disk boxFor fixing to all flat, clean surfaces with double-sided adhesive tape.
Capacity:Max. 10 CDs/DVDsor 18 (3 1/2) disks.
Material:
PolyamideColour:RAL 7033
German registered design no. M 92 07 061U.K. reg. design no. 2 029 365IR reg. design no. DM/025 474with validity for FR, IT
Packs of Model No. SZ
1 2446.000