923 VEEGUM Ultra Mosquito

8/9/2019 923 VEEGUM Ultra Mosquito

http://slidepdf.com/reader/full/923-veegum-ultra-mosquito 1/35

efore using, read, understand and comply with the information and precautions in all applicable Safety Data Sheets, labels and other product literature.nformation presented herein, while not guaranteed, was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate he date hereof. No warranty, representation or guarantee, express or implied, is made regarding accuracy, performance, stability, reliability or use.nformation is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involve other or additional sr performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such srecautions as may be required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with re

o the use, handling or further processing of any such material. No suggestion for use is intended as, and nothing herein shall be construed as, a recommendo infringe any existing patent, trademark or copyright or to violate any federal, state or local law or regulation.

Vanderbilt Minerals, LLC, 33 Winfield Street, P.O. Box 5150, Norwalk, CT 06856-5150

Telephone: (800) 562-2476 - Fax: (203) 855-1220 - Web Site: vanderbiltminerals.com

Distributed in the Interestof Product Development

VANDERBILTVEEGUM® Ultra Formulary No. 923

Minerals









Minerals

The VEEGUM®Ultra Formulary

Smectite clays are the natural choice to optimize topical suspensions and emulsions. The VEEGUM magnesiumaluminum silicate products have long been the preferred smectite clays because of their cost-effectiveness, readyavailability worldwide, high level of purity, and their exceptional uniformity in properties from lot-to-lot and year-to-year.

The primary benefit of smectite clays is their ability to stabilize a dispersion of almost anything dispersed in

water − lipids in emulsions, solids in suspensions, gases in foams. These clays are also rheology modifiers and"feel" improvers, overcoming the tacky, slimy or gummy nature of organic thickeners and other formula ingredients.

Additionally, smectite clays are resistant to degradation by bacteria, heat, UV and shear.

Fast, Low Energy HydrationConventional smectite clays are alkaline in pH, and they require energy intensive hydration. VEEGUM Ultra

overcomes these limitations. Designed for efficient incorporation into water, VEEGUM Ultra disperses easily andhydrates rapidly, and it is the only smectite rheological agent with an acid pH. Yet it provides all the benefits ofconventional smectite clay products.

All smectite clay products must be properly dispersed in water to achieve their best performance. No othermaterials should be present in the water because they can interfere with proper hydration and the formation of thecolloidal structure. With conventional smectite clays, the degree of clay hydration is directly proportional to theamount of energy used to disperse the product. The degree of hydration therefore increases as mixing time, mixingintensity or water temperature increase. VEEGUM Ultra, however, is relatively unaffected by changes in thesemixing factors. As shown in the following table, adequate hydration can be achieved quickly, even when using roomtemperature water and a simple, slow-speed propeller mixer.

VEEGUM Ultra

Water Temperature Mixer Type Mixer Speed, rpm Minimum Suggested Mixing

25°C Homogenize 3000 10 min.

25°C Propeller 800 15 min.

75°C Propeller 800 10 min.

Low pH, Bright ColorTopical products are often formulated at acid pH for optimum epidermal or active ingredient compatibility. VEEGUMUltra is tailored for these uses because of its uniquely low pH, 4.7, and its superior stabilizing ability. It is also thewhitest refined smectite available. This is dramatically evident in aqueous dispersions, which are a true bright white.Unlike many other types of clay, VEEGUM Ultra will not affect the desired whiteness or shading of emulsion orsuspension products.

Synergistic with Gums and PolymersMixtures of VEEGUM Ultra with common organic thickeners, such as xanthan gum and cellulosics, producerheology synergism and are often used to ensure optimum viscosity and stability, particularly at temperatureextremes. Smectite clay and carbomer are frequently used in topicals, since the clay provides improved feel andhigh temperature stability. They are difficult to hydrate simultaneously, however, due to the tendency of the alkalineclay to prematurely thicken the polymer. The low pH of VEEGUM Ultra avoids this difficulty. Blends with carbomerdisperse easily and hydrate quickly. Subsequent pH adjustments to thicken the carbomer and develop synergismcan be made any time after hydration, as when carbomer is used alone.

RecommendationsVEEGUM Ultra is recommended as a suspension stabilizer, emulsion optimizer and thickener for all topicalproducts. It is especially effective in products formulated at acidic pH, requiring little or no buffering while optimizingcolor and stability. The following formulas illustrate the effectiveness and versatility of this unique clay.









Minerals

FORMULARYSKIN CARE

Anti-Aging Skin Cream No. 578Intensive AHA Moisturizing Lotion No. 476Intensive AHA Moisturizing Cream No. 484Moisturizing Skin Cream No. 512Barrier Cream No. 489Vitamin Enriched Barrier Cream No. 490

TREATMENT

Botanical Skin Lightening Lotion No. 492

Licorice Extract Fade Lotion No. 604Salicylic Acid Acne Treatment Cream No. 610

AHA Clay Mask No. 486 AHA Clay Mask No. 487Mosquito Repellant Cream No. 457BB Cream No. 617CC Cream No. 618

SUN CARE

Water-Resistant Sunscreen Lotion No. 494Micro-TiO2 Sunscreen Cream No. 513Physical, Chemical UV Protection Cream No. 514

Sun Protection Cream No. 566Wash-Off Resistant Sunscreen Cream No. 515Rich Body Butter Plus Sunscreen No. 603Moisturizing Lotion with Sunscreen No. 567Moisturizing Cream with Sunscreen No. 568Water-Resistant Sport Tint No. 453

GROOMING

Liquid Hand Soap with Triclosan No. 547Body Wash Spray No. 500Pearlescent Conditioning Body Wash No. 488Body Wash Cream for Sensitive Skin No. 505Conditioning Hair & Body Shampoo No. 499

Aerosol Shave Cream for Sensitive Skin No. 503Shaving Cream No. 501Waterless Skin Scrub with D-Limonene No. 479Waterless Hand Cleaner with Abrasive No. 477








VANDERBILT Minerals Formula

Anti -Aging Sk in Cream No. 578

Wt.%VEEGUM®

Ultra Magnesium Aluminum Silicate 1.50VANZAN® NF, Xanthan Gum 0.30

A Water 75.92 Butylene Glycol 6.00Sucrose Stearate (Surfhope® SE Cosme C-18111) 3.00

Steareth-2 (Brij® S22) 1.50Steareth-21 (Brij® S7212) 1.50Cetearyl Alcohol 3.00Caprylic/ Capric Triglyceride (Neobee® M-5 Cosmetic3) 2.50PPG-11 Stearyl Ether (Acconon® E4) 2.50

B C12-15 Alkyl Benzoate (Finsolv® TN5) 1.00Cyclomethicone (Xiameter ® PMX-0345 Cyclosiloxane Blend6) 1.00Cholesterol ( Cholesterol NF2) 0.10Linoleic Acid (Emersol® 3157) 0.10Ceramide 2 (TIC-001 Ceramide 28) 0.025Ceramide 3 (Ceramide III9) 0.025Ceramide 6 II (Ceramide VI9) 0.025

C Preservative q.s.

Procedure: While heating the water to 85-90°C, slowly add the VEEGUM Ultra and VANZANNF sequentially or as a dry blend to the water agitated at maximum available shear. Mix until

fully hydrated. Add the butylene glycol and sucrose stearate, mixing until uniform. Maintain thewater phase at 85-90°C. Blend the Part B oil phase ingredients and heat to 85-90°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool with mixing; add the Part Cingredients when the emulsion is <30oC.

RAW MATERIAL SUPPLIERS1 Arch Personal Care Products L.P., SouthPlainfield, NJ

2Croda, Inc., Edison, NJ

3Stepan Company, Northfield, IL

4 Abitec Corporation, Columbus, OH5Innospec Active Chemicals, Edison, NJ

6Dow Corning Corporation, Midland, MI

7Cognis Corporation, Ambler, PA

8Takasago International Corp., Rockleigh, NJ

9Evonik Goldschmidt Chemical Corporation,Hopewell, VA

TRADEMARKS

VEEGUM and VANZAN are registered trademarks of R.T. Vanderbilt HoldingCompany, Inc. and/or its respective wholly owned subsidiaries.

Acconon is a registered trademark of Abitec Corporation.Brj is a registered trademark of Uniqema Americas LLC.Emersol is a registered trademark of Cognis Corporation.Finsolv is a registered trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Surfhope is a registered trademark of Mitsubishi Chemical Corporation.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Intensive AHA Moisturizing Lotion No. 476

Wt.%

AVEEGUM®

Ultra Magnesium Aluminum Silicate 1.50VANZAN® NF Xanthan Gum 0.50Water 73.34

BGlycerin 3.00Butylene Glycol 2.00

C

Cetyl Alcohol 1.00Glyceryl Monostearate SE 3.00Caprylic/Capric Triglyceride (Neobee® M-51) 5.00C12-15 Octanoate (Finester TM EH-252) 1.00

Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs3) 1.00Steareth-2 (Brij® S24) 0.83Steareth-21 (Brij® S7214) 0.83

DGlycolic Acid, 70 % 7.00Triethanolamine 3.20Citric Acid (to pH 3.8 ± 0.2) q.s.

E Preservative, Fragrance q.s.

Procedure: While heating the water to 75°C, slowly add the VEEGUM Ultra and VANZAN NFsequentially or as a dry blend to the water agitated at maximum available shear. Mix until fully

hydrated. Add the remaining water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 75°C. Blend the Part C oil phase ingredients and heat to 75°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool while mixing. Add the PartD and Part E ingredients when the emulsion is <40oC. Adjust as necessary to pH 3.8 ± 0.2.

RAW MATERIAL SUPPLIERS1Stepan Company, Northfield, IL

2Innospec Active Chemicals, Edison, NJ


4Croda Inc., Edison, NJ

TRADEMARKS

VEEGUM and VANZAN are registered trademarks of R.T. Vanderbilt HoldingCompany, Inc. and/or its respective wholly owned subsidiaries.Brij is a registered trademark of Uniqema Americas LLC.Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Intensive AHA Moistur izing Cream No. 484

Wt.%VEEGUM®

Ultra Magnesium Aluminum Silicate 1.5 A VANZAN® NF Xanthan Gum 0.3

Water 56.6


C

Cetyl Alcohol 0.5Glyceryl Monostearate SE 3.0Petrolatum 10.0Mineral Oil 2.0

Caprylic/Capric Triglyceride (Neobee® M-51) 3.0C12-15 Octanoate (Finester TM EH-252) 2.0Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs3) 1.0Steareth-2 (Brij® S24) 1.5Steareth-21 (Brij® S7214) 1.5Isosorbide Laurate 0.5

D

Lactic Acid USP, 88 % 2.6Sodium Lactate (PATLACTM NAL5) 2.6Glycolic Acid, 70 % 3.0Triethanolamine (to pH 3.75 ± 0.25) 3.0


Procedure: While heating the water to 80°C, slowly add the VEEGUM Ultra and VANZAN NFsequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated.Add the remaining water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 80°C. Blend the Part C oil phase ingredients and heat to 80°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool while mixing. Add the PartD and Part E ingredients when the emulsion is <40oC. Adjust as necessary to pH 3.75 ± 0.25.




4

Croda Inc., Edison, NJ5RITA Corporation, Crystal Lake, IL

TRADEMARKS

VEEGUM and VANZAN are registered trademarks of R.T. Vanderbilt HoldingCompany, Inc. and/or its respective wholly owned subsidiaries.Brij is a registered trademark of Uniqema Americas LLC.

Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Patlac is a trademark of RITA Corporation.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Moisturizing Skin Cream No. 512

Wt.%VEEGUM Ultra, Magnesium Aluminum Silicate 2.0

A Carbomer (Carbopol® Ultrez 101) 0.2Water 72.5

BGlycerin 5.0Butylene Glycol 3.0Polysorbate 20 (Tween® 202) 1.0

C

Cetyl Alcohol 0.5Glyceryl Monostearate SE 3.0Caprylic/Capric Triglyceride (Neobee® M-53) 5.0

C12-15 Octanoate (Finester™ EH-254) 3.0Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs5) 1.0Steareth-2 (Brij® S22) 1.1Steareth-21 (Brij® S7212) 1.1Laureth-23 (Brij® L232) 0.5Isosorbide Laurate 1.0

DEtidronic Acid 0.1Triethanolamine (to pH 6.0 ± 0.5) q.s.


Procedure: Begin heating the water to 75-80°C. Slowly add the VEEGUM Ultra and carbomersequentially or as a dry blend to the water agitated at maximum available shear. Mix untilhydrated. Add the remaining water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 75-80°C. Blend the Part C oil phase ingredients and heat to 75-80°C. Addthe oil phase to the water phase with good agitation; mix until uniform. Cool while mixing; addthe Part D and Part E ingredients when the emulsion is <35oC. Adjust as necessary to pH6.0+0.5.

RAW MATERIAL SUPPLIERS1Lubrizol Advanced Materials Inc.,

Cleveland, OH2Croda Inc., Edison, NJ


4

Innospec Active Chemicals, Edison, NJ5Dow Corning Corporation, Midland, MI

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij and Tween are registered trademarks of Uniqema Americas LLC.Carbopol is a registered trademark of Lubrizol Advanced Materials, Inc.

Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Barrier Cream No. 489

Wt.%

AVEEGUM®

Ultra, Magnesium Aluminum Silicate 0.50Carbomer (Carbopol® 9341) 0.25Water 88.31

B

Cetyl Alcohol 0.50Glyceryl Monostearate SE 2.00C12-15 Octanoate (Finester™ EH-252) 3.00Castor Oil Polyurethane (Polyderm™ PPI CO3) 1.00Phenyl Dimethicone (DC 556 Fluid4) 3.00Steareth-2 (Brij® S25) 0.72Steareth-21 (Brij® S7215) 0.72

D Preservative, Fragrance q.s.

E Triethanolamine (to pH 5.8 ± 0.3) q.s.

Procedure: Begin heating the water to 80°C. Slowly add the VEEGUM Ultra and carbomersequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Maintain the water phase at 80°C. Blend the Part B oil phase ingredients and heat to80°C. Add the oil phase to the water phase with good agitation; mix until uniform. Cool whilemixing; add the Part D ingredients when the emulsion is < 35oC. Adjust as necessary to pH 5.8± 0.3.


Cleveland, OH2Innospec Active Chemicals, Edison, NJ

3 Alzo International Inc., Sayreville, NJ4Dow Corning Corporation, Midland, MI


TRADEMARKSVEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij is a registered trademark of Uniqema Americas LLC.Carbopol is a registered trademark of Lubrizol Advanced Materials, Inc.Finester is a trademark of Innospec Performance Chemicals Company.Polyderm is a trademark of Alzo Investments.

rev04/25/2013









Vitamin Enriched Barr ier Cream No. 490

Wt.%VEEGUM®

Ultra, Magnesium Aluminum Silicate 0.80 A Carbomer (Carbopol® 9341) 0.30

Water 79.00


C

Cetyl Alcohol 0.50Glyceryl Monostearate SE 2.00Caprylic/Capric Triglyceride (Neobee® M-52) 2.00C12-15 Octanoate (Finester™ EH-253) 2.00

Castor Oil Polyurethane (Polyderm™ PPI CO4) 1.00Phenyl Dimethicone (DC 556 Fluid5) 3.00Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs 5) 1.00Bois Oil 0.50Steareth-2 (Brij® S26) 0.95Steareth-21 (Brij® S7216) 0.95

D

Panthenol 1.00Vitamin E Acetate 0.50Vitamin A Palmitate 0.50Triethanolamine (to pH 5.8 ± 0.3) q.s.


Procedure: Begin heating the water to 80°C. Slowly add the VEEGUM Ultra and carbomersequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Add the remaining water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 80°C. Blend the Part C oil phase ingredients and heat to 80°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool while mixing; add the PartD and Part E ingredients when the emulsion is < 35oC. Adjust as necessary to pH 5.8±0.3.


Cleveland, OH2Stepan Company, Northfield, IL

3

Innospec Active Chemicals, Edison, NJ4 Alzo International Inc., Sayreville, NJ5Dow Corning Corporation, Midland, MI


TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij is a registered trademark of Uniqema Americas LLC.

Carbopol is a registered trademark of Lubrizol Advanced Materials, Inc.Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Polyderm is a trademark of Alzo Investments.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Botanical Skin Lightening Lot ion No. 492Wt.%

VEEGUM®Ultra, Magnesium Aluminum Silicate 2.0

A Carbomer (Carbopol® 9341) 0.2Water 69.8

BPolysorbate 20 (Tween® 202) 0.6Glycerin 3.0Butylene Glycol 3.0

C

Cetyl Alcohol 0.5Isosorbide Laurate 1.0Laureth-23 (Brij® L232) 0.7

Steareth-2 (Brij®

S22

) 1.1Steareth-21 (Brij® S7212) 1.1Caprylic/Capric Triglyceride (Neobee® M-53) 5.0Glyceryl Monostearate SE 3.0C12-15 Octanoate (Finester™ EH-254) 3.0Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs 5) 1.0

D

Triethanolamine (pH to 6.0 + 0.5) 3.0Saxifraga Sarmentosa Extract (and) Grape Extract (and) Butylene Glycol (and)Water (and) Mulberry Root Extract (and) Scultellaria Baicalensis Extract (and) Na2

EDTA (Biowhite®6)

2.0

E Preservative, Fragrance, Chelating Agent q.s.

Procedure: Begin heating the water to 75-80°C. Slowly add the VEEGUM Ultra and carbomersequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Add the water phase ingredients from Part B, mixing until uniform. Maintain the waterphase at 75-80°C. Blend the Part C oil phase ingredients and heat to 75-80°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool while mixing; when theemulsion is <45oC add the Part D and Part E ingredients in the order listed, mixing after eachaddition until smooth and uniform. Adjust as necessary to pH 6.0+0.5.



3Stepan Company, Northfield, IL4Innospec Active Chemicals, Edison, NJ


6BASF Corporation, Florham Park, NJ

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Biowhite is a registered trademark of BASF Beauty Care Solutions.

Brij and Tween are registered trademarks of Uniqema Americas LLC.Carbopol is a registered trademark of Lubrizol Advanced Materials, Inc.Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Licorice Extract Fade Lotion No. 604

Wt. %

A

VEEGUM®Ultra Magnesium Aluminum Silicate 1.5

Water 65.8Propanediol (Zemea® Propanediol1) 5.0Disodium EDTA 0.2Panthenol and Propylene Glycol (D-Panthenol 50-P2) 0.4

B

White Petrolatum 5.0Dimethicone (Xiameter ® PMX-200 Silicone Fluid 350cs3) 1.0Polyglyceryl-3 distearate (Cremophor ® GS 322) 3.0Ceteareth-25 (Cremophor ® A 252) 1.5Cetearyl alcohol 3.0

Tocopherol Acetate (Vitamin E Acetate USP/EP/ FCC2) 0.5Glyceryl Stearate (and) PEG-100 Stearate (Arlacel®1654) 2.0Ethyl Hexyl Methoxycinnamate (Neo Heliopan® AV5) 7.5

CGlycyrrhizza Glabra (Licorice) Root Extract (Licorice Extract CG 4%6) 0.5Ethanol, USP 3.0

D Retinyl Palmitate (Vitamin A Palmitate PH. EUR/USP/FCC2) 0.1

EPreservative q.s.Triethanolamine, 99% q.s.

Procedure: While heating the water to 70-75ºC, slowly add the VEEGUM® Ultra while agitatingat maximum available shear. Mix until fully hydrated. Add the remaining Part A water phaseingredients. Maintain the water phase at 70-75ºC. Combine the Part B oil phase ingredients andheat to 70-75ºC. Add the oil phase to the water phase with good agitation; mix until uniform.Cool while mixing to 40-45oC. Dissolve the licorice extract in the ethanol under agitation andthen add Part C to the emulsion; mix until uniform. Warm the retinyl palmitate to liquefy andmake uniform prior to weighing out. Add the retinyl palmitate and the preservative in order to theemulsion, mixing after each addition until uniform. Adjust as necessary to pH 6.0+0.5.

RAW MATERIAL SUPPLIERS1DuPont Tate & Lyle Bio ProductsCompany, LLC, Wilmington, DE


3

Dow Corning Corporation, Midland, MI4Croda, Inc., Edison, NJ

5Symrise, Teterboro, NJ

6Sabinsa Corporation, Piscataway, NJ

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.

Arlacel is a registered trademark of Uniqema Americas LLC.

Cremophor is a registered trademark of BASF Aktiengesellschaft.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.Xiameter is a registered trademark of Dow Corning Corporation.Zemea is a registered trademark of DuPont Tate & Lyle Bio Products Company, LLC.

rev04/25/2013









Salicylic Acid Acne Treatment Cream No. 610

Wt.%

A


VANZAN® NF Xanthan Gum 0.5Water 73.4Etidronic Acid 0.1Propanediol (Zemea® propanediol1) 5.0

B

Salicylic Acid - USP 1.0Steareth-21 ( Brij® S7212) 1.5Steareth-2 (Brij® S22) 3.5Cetearyl Alcohol (Protachem™ CS-503) 1.5Stearic Acid (Pristerene® 95592) 2.0

PPG-15 Stearyl Ether (Arlamol® PS15E2) 8.0Dimethicone (Xiameter ® PMX-200 Silicone Fluid 350cs 4) 1.0

C Preservative q.s.

Triethanolamine (Adj. pH to 3.8 ± 0.2) q.s.

Procedure: While heating the water to 80-85ºC, slowly add the VEEGUM Ultra and VANZANNF sequentially or as a dry blend while mixing at maximum available shear. Continue mixinguntil fully hydrated. Add the etidronic acid and propanediol in order, mixing after each additionuntil uniform. Maintain the water phase at 80-85ºC. Combine the Part B oil phase ingredientsand heat to 80-85ºC. Add Part B to Part A slowly with adequate mixing; homogenize. Coolgradually while mixing. Add the preservative when the emulsion is <30oC, then adjust the pH to

3.8 ± 0.20 with triethanolamine.



3Protameen, Totowa, NJ


TRADEMARKS


Arlamol and Brij are registered trademarks of Uniqema Americas LLC.Pristerene is a registered trademark of Unichema Chemie B.V.Protachem is a trademark Protameen Chemicals, Inc.Xiameter is a registered trademark of Dow Corning Corporation.Zemea is a registered trademark of DuPont Tate & Lyle Bio Products Company, LLC.

rev04/25/2013









AHA Clay Mask No. 486

Wt.%

AVEEGUM®

Ultra, Magnesium Aluminum Silicate 5.00Water 38.75

B

Glycerin 3.00Butylene Glycol 3.00Cosmetic Kaolin Clay 30.00Cosmetic Talc 5.00Sodium Lauroyl Sarcosinate, 30% 5.00

C Glycolic Acid, 70% 7.00

D Triethanolamine 3.75Citric Acid (to pH 4.0 ± 0.2) q.s.


Procedure: Add the VEEGUM Ultra to the water vortex while agitating at maximum availableshear. Continue mixing until fully hydrated. Add the remaining ingredients in the order listed,mixing after each addition until smooth.

TRADEMARKS


rev04/25/2013









AHA Clay Mask No. 487

Wt.%

AVEEGUM®


B

Glycerin 5.0Butylene Glycol 3.0Cosmetic Kaolin Clay 30.0Cosmetic Talc 5.0Sodium Lauroyl Sarcosinate, 30% 5.0Glycolic Acid, 70% 5.0d-Panthenol 0.5Vitamin E Acetate 0.1

Vitamin A Palmitate 0.1Triethanolamine 2.4

C Preservative, Fragrance q.s.

Procedure: Add the VEEGUM Ultra to the water vortex while agitating at maximum availableshear. Continue mixing until fully hydrated. Add the remaining ingredients in the order listed,mixing after each addition until smooth.

TRADEMARKS


rev04/25/2013









Mosqui to Repellant Cream No. 457

Wt.%

AVEEGUM® Ultra Magnesium Aluminum Silicate 0.4Carbomer (Carbopol® 9401) 0.4Water 79.2

B N,N-Diethyl-m-Toluamide 15.0Glyceryl Stearate (and) PEG-100 Stearate(Arlacel ® 1652)

5.0

C Sodium Hydroxide solution to pH 5.5 q.s.

D Preservative q.s.

Procedure: Begin heating the water to 50-55°C. Slowly add the VEEGUM Ultra and carbomersequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Maintain Part A at 50-55°C. Heat Part B to 50-55°C. Add Part A to Part B with goodagitation. Cool with mixing; add the sodium hydroxide and preservative when the emulsion is<35oC.

RAW MATERIAL SUPPLIERS1Lubrizol Advanced Materials, Inc.,

Cleveland, OH2Croda, Inc., Edison, NJ

TRADEMARKS


Arlacel is a registered trademark of Uniqema Americas LLC.Carbopol is a registered trademark of Lubrizol Advanced Materials, Inc.

rev04/25/2013








VANDERBILT Minerals FormulaBB Cream No. 617

Wt.%

A


Water 59.62Propanediol (Zemea® Propanediol1) 5.00Disodium EDTA 0.20Panthenol and Propylene Glycol (D-Panthenol 50-P2) 0.40

B

Iron Oxides (and) Microcrystalline Cellulose (C2-5 Yellow LLXLO3) 0.40

Iron Oxide (C.I. 77491) (and) Cellulose (C2-5 Red R-516L3) 0.10

Iron Oxide (C.I. 77499 ) (and) Cellulose (C2-5 Black BL-1003) 0.03

Titanium Dioxide (and) Cellulose (and) Alumina (C2-5 TiO2 CR-503) 3.50

C

Crambe Abyssinica Seed Oil (Fancor ® Abyssinian Oil4) 2.50

Dimethicone (Xiameter PMX-200 Silicone Fluid 350cs5) 1.00

Polyglyceryl-3 distearate (Cremophor ®

GS 322

) 3.10Ceteareth-25 (Cremophor ® A 25

2) 1.50

Cetearyl alcohol 3.00

Glyceryl Stearate (and) PEG-100 Stearate (Arlacel 165 VEG6) 2.00

Ethyl Hexyl Methoxycinnamate (Neo Heliopan® AV7) 7.50

Mica (Sericite GMS-4C3) 3.00

D

Mica (and) Titanium Dioxide (and) Ethylene/Methacrylate Copolymer (and)Isopropyl Titanium Triisostearate (SPC/KTZ Interval Gold-123)

0.15

E

Preservative q.s.

Lactobacillus/Salix Alba Bark Ferment Filtrate (Prorevive BB Complex8) 5.50

Triethanolamine, 99% q.s.

Procedure:While heating the water to 70-75ºC, slowly add the VEEGUM®

Ultra while agitating at maximumavailable shear. Mix until fully hydrated. Add the remaining Part A water phase ingredients.Combine the Part B ingredients, then add to Part A and mix until smooth. Maintain the water phaseat 70-75ºC. Combine the Part C, oil phase ingredients and heat to 70-75ºC. Add the oil phase tothe water phase with good agitation; mix until uniform. Switch to low shear mixing, then add theSPC/KTZ Interval Gold-12 (Part D). Cool while mixing to 30-35oC, then add the preservativefollowed by the Prorevive BB complex to the emulsion, mixing after each addition until uniform. Adjust as necessary to pH 6.0+0.5 with triethanolamine.



3Kobo Products, Inc., South Plainfield, NJ

4Elementis Specialties, Hightstown, NJ

5

Dow Corning Corporation, Midland, MI6Croda, Inc., Edison, NJ


8 Active Concepts, LLC, Lincolnton, NC

TRADEMARKSVEEGUM is a registered trademark of R.T. Vanderbilt HoldingCompany, Inc. or its respective wholly owned subsidiaries. Arlacel is a registered trademark of Uniqema Americas LLC.Cremophor is a registered trademark of BASF Aktiengesellschaft.

Fancor is a registered trademark of Elementis Specialties, Inc.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.Xiameter is a registered trademark of Dow Corning Corporation.Zemea is a registered trademark of DuPont Tate & Lyle Bio ProductsCompany, LLC.

01/10/2014








VANDERBILT Minerals FormulaCC Cream No. 618

Wt.%

A

VEEGUM®

Ultra Magnesium Aluminum Silicate 1.50Water 61.27Propanediol (Zemea® Propanediol1) 5.00Disodium EDTA 0.20Panthenol and Propylene Glycol (D-Panthenol 50-P2) 0.40

B

Iron Oxides (and) Microcrystalline Cellulose (C2-5 Yellow LLXLO3) 0.40Iron Oxide (C.I. 77491) (and) Cellulose (C2-5 Red R-516L

3) 0.10

Iron Oxide (C.I. 77499 ) (and) Cellulose (C2-5 Black BL-1003) 0.03Titanium Dioxide (and) Cellulose (and) Alumina (C2-5 TiO2 CR-503) 3.50

C

Crambe Abyssinica Seed Oil (Fancor Abyssinian Oil4) 2.50

Dimethicone (Xiameter PMX-200 Silicone Fluid 350cs5) 1.00

Polyglyceryl-3 distearate (Cremophor GS 322) 3.00

Ceteareth-25 (Cremophor A 252

) 1.50Cetearyl alcohol 3.00Tocopherol Acetate (Vitamin E Acetate Care DL-alpha-Tocopherol acetate2) 0.50Glyceryl Stearate (and) PEG-100 Stearate (Arlacel 165 VEG6) 2.00Ethyl Hexyl Methoxycinnamate (Neo Heliopan AV

7) 7.50

Mica (Sericite GMS-4C3) 3.00

DGlycyrrhizza Glabra (Licorice) Root Extract (Licorice Extract CG 4%8) 0.50Ethanol, USP 3.00

E Retinyl Palmitate (Vitamin A Palmitate 1.7 Mio I.E./g2) 0.10

FPreservative q.s.Triethanolamine, 99% q.s.

Procedure:While heating the water to 70-75ºC, slowly add the VEEGUM

®Ultra while agitating at maximum

available shear. Mix until fully hydrated. Add the remaining Part A water phase ingredients. Combine thePart B ingredients, then add to Part A and mix until smooth. Maintain the water phase at 70-75ºC.Combine the Part C, oil phase ingredients and heat to 70-75ºC. Add the oil phase to the water phasewith good agitation; mix until uniform. Cool while mixing to 40-45

oC. Dissolve the licorice extract in the

ethanol under agitation and then add Part D to the emulsion. Warm the retinyl palmitate to liquefy andmake uniform prior to weighing out. Add the retinyl palmitate and mix until uniform. Continue to coolwhile mixing to 30-35ºC, then add the preservative. Mix until uniform. Adjust as necessary to pH 6.0+0.5with triethanolamine.



3

Kobo Products, Inc., South Plainfield, NJ4Elementis Specialties, Hightstown, NJ


6Croda, Inc., Edison, NJ


8Sabinsa Corporation, Piscataway, NJ

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries. Arlacel is a registered trademark of Uniqema Americas LLC.

Cremophor is a registered trademark of BASF Aktiengesellschaft.Fancor is a registered trademark of Elementis Specialties, Inc.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.Xiameter is a registered trademark of Dow Corning Corporation.Zemea is a registered trademark of DuPont Tate & Lyle Bio Products Company, LLC.

01/07/2014









Water-Resistant Sunscreen Lot ion No. 494

Wt.%VEEGUM®

Ultra, Magnesium Aluminum Silicate 2.0 A Carbomer (Ultrez™101) 0.2

Water 64.6


C

Cetyl Alcohol 1.0Isosorbide Laurate 1.0Glyceryl Monostearate SE 3.0C12-15 Octanoate (Finester™ EH-252) 5.0

Octylmethoxycinnamate (Parsol® MCX3) 7.5 Avobenzone (Parsol® 17893) 2.0Castor Oil Polyurethane (Polyderm™ PPI-CO4) 1.0Phenyl Dimethicone (DC 556 Fluid5) 3.0Steareth-2 (Brij® S26) 1.8Steareth-21 (Brij® S7216) 1.8

D Disodium EDTA 0.1

ETriethanolamine (to pH 6.0 + 0.5) q.s.Preservative, Fragrance q.s.

Procedure: Begin heating the water phase to 75°C. Slowly add the VEEGUM Ultra andcarbomer sequentially or as a dry blend to the water agitated at maximum available shear. Mixuntil fully hydrated. Add the water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 75°C. Blend the oil phase ingredients of Part C and heat to 75°C. Add theoil phase to the water phase with high shear mixing. Mix at reduced speed while cooling to45°C; then add Part D followed by Part E. Adjust as necessary to pH 6.0+0.5.


Cleveland, OH2Innospec Active Chemicals, Edison, NJ

3Givaudan Corporation, Teaneck, NJ


6Croda Inc, Edison, NJ

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij is a registered trademark of Uniqema Americas LLC.Finester is a trademark of Innospec Performance Chemicals Company.Parsol is a registered trademark of Givaudan Corporation.Polyderm is a trademark of Alzo Investments.

Ultrez is a trademark of Noveon IP Holdings.rev04/25/2013









Micro-TiO2 Sunscreen Cream No. 513 Wt.%

VEEGUM®

Ultra, Magnesium Aluminum Silicate 2.0

A Carbomer (Ultrez™101) 0.2Water 52.5

B

Polysorbate 20 (Tween®202) 1.0

Aqua (and) Titanium Dioxide (and) Alumina (and) Silica (and) Sodium Polyacrylate(and) Propylene Glycol (and) Diazolidinyl Urea (and) Methyl Paraben (and) PropylParaben (Tioveil® AQ-G2)

25.0

Butylene Glycol 3.0

C

Cetyl Alcohol 0.5Isosorbide Laurate 1.0

Caprylic/Capric Triglyceride (Neobee® M-53) 5.0

Glyceryl Monostearate SE 3.0C12-15 Octanoate (Finester™ EH-254) 3.0Dimethicone (Xiameter ® PMX-200 Silicone Fluid 350cs5) 1.0Laureth-23 (Brij® L232) 0.5Steareth-2 (Brij® S22) 1.1Steareth-21 (Brij® S7212) 1.1

D Etidronic Acid 0.1


Procedure: Begin heating the water phase to 80°C. Slowly add the VEEGUM Ultra andcarbomer sequentially or as a dry blend to the water agitated at maximum available shear. Mixuntil fully hydrated. Add the water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 80°C. Blend the oil phase ingredients of Part C and heat to 80°C. Add theoil phase to the water phase with high shear mixing. Mix at reduced speed while cooling to45°C; then add Part D followed by Part E. Adjust as necessary to pH 6.0+0.5.



3Stepan Company, Northfield, IL4Innospec Active Chemicals, Edison, NJ


TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij and Tween are registered trademarks of Uniqema Americas LLC.

Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Tioveil is a registered trademark of Acma Limited Corporation.Ultrez is a trademark of Noveon IP Holdings.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013



efore using, read, understand and comply with the information and precautions in all applicable Safety Data Sheets, labels and other product literaturenformation presented herein, while not guaranteed, was prepared by technical personnel and, to the best of our knowledge and belief, is true and accurate he date hereof. No warranty, representation or guarantee, express or implied, is made regarding accuracy, performance, stability, reliability or use.nformation is not intended to be all-inclusive, because the manner and conditions of use, handling, storage and other factors may involve other or additional sr performance considerations. The user is responsible for determining the suitability of any material for a specific purpose and for adopting such srecautions as may be required. Vanderbilt Minerals, LLC does not warrant the results to be obtained in using any material, and disclaims all liability with re





VANDERBILT Minerals FormulaPhysical, Chemical UV Protection Cream No. 514

Wt.%

VEEGUM® Ultra, Magnesium Aluminum Silicate 2.0

A Carbomer (Ultrez™101) 0.2Water 51.4

B

Polysorbate 20 (Tween® 202) 1.0

Aqua (and) Titanium Dioxide (and) Alumina (and) Silica (and) SodiumPolyacrylate (and) Propylene Glycol (and) Diazolidinyl Urea (and) MethylParaben (and) Propyl Paraben (Tioveil® AQ-G2)

12.5

Butylene Glycol 3.0

C

Cetyl Alcohol 0.5Isosorbide Laurate 1.0


Glyceryl Monostearate SE 3.0C12-15 Octanoate (Finester™ EH-254) 3.0

Octylmethoxycinnamate (Parsol® MCX5) 7.0

Avobenzone (Parsol® 17895) 2.0

Octyl Salicylate (Dermoblock™ OS6) 3.0Dimethicone (Xiameter PMX-200 Silicone Fluid 350cs7) 1.0

Laureth-23 (Brij® L232) 0.5

Steareth-2 (Brij® S22) 1.9

Steareth-21 (Brij® S7212) 1.9



Procedure: Begin heating the water phase to 80°C. Slowly add the VEEGUM Ultra andcarbomer sequentially or as a dry blend to the water agitated at maximum available shear. Mixuntil fully hydrated. Add the water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 80°C. Blend the oil phase ingredients of Part C and heat to 80°C. Add theoil phase to the water phase with high shear mixing. Mix at reduced speed while cooling to 45°Cand then add Part D followed by Part E. Adjust as necessary to pH 6.0+0.5.

Note: The combination of TiO2 and Avobenzone is not approved for use in the USA.




4Innospec Active Chemicals, Edison, NJ5Givaudan Corporation, Teaneck, NJ


TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij and Tween are registered trademarks of Uniqema Americas LLC.Dermoblock is a trademark of Alzo International, Inc.

Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Parsol is a registered trademark of Givaudan Corporation.Tioveil is a registered trademark of Acma Limited Corporation.Ultrez is a trademark of Noveon IP Holdings.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Sun Protect ion Cream No. 566

Wt.%

A

VEEGUM®Ultra, Magnesium Aluminum Silicate 1.0

Water 57.8Glycerin, 96% 2.7Zinc Oxide (Zinc Oxide Neutral1) 10.0

B

Glyceryl Stearate (and) PEG-100 Stearate (Arlacel® 1652) 4.0Ceteareth-20 (Eumulgin® B-23) 1.0Cetearyl Alcohol 3.0Caprylic/Capric Triglyceride (Neobee® M-54) 4.0Dicaprylyl Ether (Cetiol® OE3) 3.0Dimethicone (Xiameter ® PMX-200 Silicone Fluid 350cs5) 1.0

Octyl Salicylate (Neo Heliopan® OS1) 5.0Octyl Methoxycinnamate (Neo Heliopan® AV1) 7.5


Procedure: Begin heating the water to 75-80°C. Slowly add the VEEGUM Ultra to the wateragitated at maximum available shear. Mix until fully hydrated. Add the remaining water phaseingredients; mix until the zinc oxide is uniformly dispersed. Maintain the water phase at 75-80ºC.Heat Part B to 75-80ºC. Add Part B to Part A; homogenize for 5 minutes at 75-80ºC. Cool whilemixing slowly to 40ºC. Add Part C and mix until homogeneous.

RAW MATERIAL SUPPLIERS1

Symrise, Teterboro, NJ2Croda Inc., Edison, NJ




TRADEMARKS


Arlacel is a registered trademark of Uniqema Americas LLC.Cetiol and Eumulgin are registered trademarks of Cognis GmbH Corporation.Neobee is a registered trademark of Stepan Company.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013








VANDERBILT Minerals FormulaWash-Off Resistant Sunscreen Cream No. 515

Wt.%VEEGUM® Ultra, Magnesium Aluminum Silicate 2.0

A Carbomer (UltrezTM 101) 0.2Water 47.8

B

Polysorbate 20 (Tween® 202) 1.0 Aqua (and) Titanium Dioxide (and) Alumina (and) Silica (and) SodiumPolyacrylate (and) Propylene Glycol (and) Diazolidinyl Urea (and) MethylParaben (and) Propyl Paraben (Tioveil® AQ-G2)

12.5

Butylene Glycol 3.0

C

Cetyl Alcohol 0.5Isosorbide Laurate 1.0Caprylic/Capric Triglyceride (Neobee® M-53) 5.0Glyceryl Monostearate SE (Cutina® GMS SE4) 3.0

C12-15 Octanoate (Finester

TM

EH-25

5

) 3.0Octylmethoxycinnamate (Parsol® MCX6) 7.0 Avobenzone (Parsol® 17896) 2.0Octyl Salicylate (Dermoblock™ OS7) 3.0Castor Oil Polyurethane (Polyderm™ PPI-CO7) 1.0Phenyl Dimethicone (DC 556 Fluid8) 3.0Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs8) 1.0Laureth-23 (Brij® L232) 0.5Steareth-2 (Brij® S22) 2.2Steareth-21 (Brij® S7212) 2.2


ETriethanolamine (to pH 6.0 + 0.5) q.s.Preservative q.s.

Procedure: Begin heating the water to 80°C. Slowly add the VEEGUM Ultra and carbomersequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Add the remaining water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 80°C. Blend the Part C oil phase ingredients and heat to 85°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool with mixing; add the Part Dand Part E ingredients when the emulsion is <45oC. Adjust as necessary to pH 6.0+0.5.

Note: The combination of TiO2 and Avobenzone is not approved for use in the USA.

RAW MATERIAL SUPPLIERS1 Lubrizol Advanced Materials, Inc., Cleveland,OH





6Givaudan Corporation, Teaneck, NJ


TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Brij and Tween are registered trademarks of Uniqema Americas LLC.Cutina is a registered trademark of Cognis IP Management GmbH.Dermoblock is a trademark of Alzo International, Inc.Finester is a trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Parsol is a registered trademark of Givaudan Corporation.Polyderm is a trademark of Alzo Investments.Tioveil is a registered trademark of Acma Limited Corporation.Ultrez is a trademark of Noveon IP Holdings.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Rich Body But ter Plus Sunscreen No. 603

Wt.%

A


VANZAN® NF Xanthan Gum 0.5Water 58.5Glycerin 3.0Sorbeth-30 2.0

B

C12-15 Alkyl Benzoate (Finsolv® TN1) 2.0Dimethicone (Xiameter ® PMX-200 Silicone Fluid 350cs2) 1.0Soybean (Glycine Soja) Oil (Super Refined® Soybean USP3) 2.5Butyrospermum Parkii (Shea) Butter (Tomasa Shea Butter 4) 3.5Isopropyl Myristate (and) Glycine Soja (Soybean) Oil (and) Retinyl Palmitate

(and) Carthamus Tinctorius (Safflower) Seed Oil (and) Linoleic Acid (and)Tocopherol (Vitamin Complex AEF OS3)

1.0

Stearyl Alcohol (Lanette® 185) 5.0Glyceryl Stearate (and) PEG-100 Stearate (Arlacel® 1653) 5.0C12-15 Alkyl Benzoate (and) Titanium Dioxide (and) Aluminum Stearate (and)Polyhydroxystearic Acid (and) Alumina (Solaveil® CT-1003) 15.0

C Preservative q.s.

Procedure: While heating the water to 70-75°C, slowly add the VEEGUM Ultra and VANZANNF sequentially or as a dry blend to the water agitated at maximum available shear. Mix until

fully hydrated. Add the remaining water phase ingredients, mixing until uniform. Maintain

the water phase at 70-75°C. Combine Part B ingredients and heat to 70-75ºC. Add the oilphase to the water phase with good agitation; mix until uniform. Cool with mixing; add the

Part C ingredients when the emulsion is <30oC. If necessary, adjust the pH to 6.5 ± 0.5.

RAW MATERIAL SUPPLIERS1Innospec Active Chemicals, Edison, NJ



4Tri-K Industries, Inc., Northvale, NJ


TRADEMARKS


Arlacel is a registered trademark of Uniqema Americas LLC.Finsolv is a registered trademark of Innospec Performance Chemicals Company.Lanette is a registered trademark of Cognis IP Management GmbH.Solaveil is a registered trademark of Croda International PLC.Super Refined is a registered trademark of Croda, Inc.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Moisturizing Lotion w ith Sunscreen No. 567

Wt.%

A



B

Glyceryl Stearate (and) Ceteareth-20 (and) Ceteareth-12 (and) Cetearyl Alcohol (and)Cetyl Palmitate (Emulgade® SE-PF2)

6.0

Glyceryl Stearate (Kessco® GMS Pure3) 2.0Caprylic/Capric Triglyceride (Neobee® M-53) 5.0Mineral Oil, USP/NF Grade 2.0Octyl Methoxycinnamate (Neo Heliopan® AV1) 2.0


Procedure: While heating the water to 85oC, slowly add the VEEGUM Ultra while mixing atmaximum available shear. Mix until fully hydrated. Add the remaining water phase ingredients,mixing until the zinc oxide is uniformly dispersed. Maintain the water phase at 85°C. Blend thePart B oil phase ingredients and heat to 85ºC. Add the oil phase to the water phase with goodagitation; mix until uniform. Cool with mixing; add the Part C ingredients when the emulsion is<30oC.

RAW MATERIAL SUPPLIERS1Symrise, Teterboro, NJ



TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Emulgade is a registered trademark of Cognis GmbH Corporation.Kessco and Neobee are registered trademarks of Stepan Company.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.

rev04/25/2013









Moisturizing Cream with Sunscreen No. 568

Wt.%

A



BEmulsifying Wax NF (Polawax™ NF2) 12.0PPG-2 Myristyl Ether Propionate (Crodamol™ PMP2) 4.0Octyl Methoxycinnamate (Neo Heliopan® AV1) 2.0

C Preservative q.s.

Procedure: While heating the water to 75-80oC, slowly add the VEEGUM Ultra while mixing atmaximum available shear. Mix until fully hydrated. Add the remaining water phase ingredients,mixing until the zinc oxide is uniformly dispersed. Maintain the water phase at 75-80oC. Blend thePart B oil phase ingredients and heat to 75-80oC. Add the oil phase to the water phase with goodagitation; mix until uniform. Cool with mixing; add Part C when the emulsion is <30oC.



TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Crodamol and Polawax are trademarks of Croda, Inc.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.

rev04/25/2013





Vanderbilt Minerals, LLC, 33 Winfield Street, P.O. Box 5150, Norwalk, CT 06856-5150Telephone: (800) 562-2476 - Fax: (203) 855-1220 - Web Site: vanderbiltminerals.com



Water-Resistant Spor t Tint No. 453

Procedure Slowly add the VEEGUM Ultra and VANZAN NF sequentially or as a dry blend tothe water agitated at maximum available shear. Mix until fully hydrated. Add the propyleneglycol. Blend Part B thoroughly; grind if necessary. Slowly add Part B to Part A and mix untilsmooth and uniform. Blend Part C ingredients and add to Part A+B; mix until homogeneous.

Add Part D ingredients in order, mixing until smooth and uniform.


2RITA Corporation, Crystal Lake, IL


4International Specialty Products, Wayne, NJ

TRADEMARKS

VEEGUM and VANZAN are registered trademarks of R.T. Vanderbilt HoldingCompany, Inc. and/or its respective wholly owned subsidiaries.Crodafos is a trademark of Croda, Inc.Neo Heliopan is a registered trademark of Haarmann & Reimer GmbH.Ritachol is a registered trademark of RITA Corporation.

rev04/25/2013

Wt.%

A

VEEGUM®


VANZAN®

NF, Xanthan Gum 0.40

Water 70.40Propylene Glycol 5.00

B

Iron Oxides 0.67Manganese Violet 0.10Talc 4.27Titanium Dioxide 6.96

C

Isocetyl Alcohol 3.00Octyl Methoxycinnamate (Neo Heliopan® AV1) 3.00Mineral Oil (and) Lanolin Alcohol (Ritachol®2) 2.00DEA-Oleth-3 Phosphate (Crodafos™ O3D3) 2.20

DPVP (PVP K-904) 0.40Preservative, Fragrance q.s.









Liqu id Hand Soap with Tric losan No. 547

Wt.%

AVEEGUM®


BSodium Hydroxide 1.0Water 15.0

CCocoyl Sarcosine 20.0Triclosan (Irgasan® DP-300 Bacteriostat1) 0.3


Procedure: Slowly add the VEEGUM Ultra to the water while mixing at maximum availableshear. Mix until fully hydrated. Dissolve the NaOH in the water to make Part B. Dissolve theTriclosan in the cocyl sarcosine to make Part C. Add Part B to Part A; stir for 1-2 minutes. AddPart C to Part A+B and continue stirring with medium speed until uniform. Avoid air entrapment.

Add Part D and mix until uniform. This formula can easily be converted to a hand scrub by theincorporation of 1% polyethylene beads or pumice.

R.T. Vanderbilt Company, Inc. has performed a basic study that demonstrates that Triclosansolubilized in cocoyl sarcosine retains microbial inhibition of Pseudomonas aeruginosa andStaphylococcus aureus, sub. aureus. To make a claim that a personal care product is"antibacterial" requires the submission of supporting data to the U.S. EPA or FDA. R.T.Vanderbilt Company, Inc. makes no representation that the use of Triclosan in these formulas

will fulfill regulatory requirements.RAW MATERIAL SUPPLIERS1Ciba Specialty Chemicals Corp.,

Tarrytown, NY

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Irgasan is a registered trademark of Ciba Specialty Chemicals Corporation.

rev04/25/2013









Body Wash Spray No. 500

Wt.%

AVEEGUM®


Water 58.5

B

Disodium Laureth Sulfosuccinate (Stepan Mild -SL31) 13.0

Cocamidopropyl Hyroxysultaine (Mirataine® CBS2) 5.0

Polysorbate 20 (Tween®203) 1.5

Cocaimdopropyl Betaine (Amphosol® CA1) 3.0

Sodium Laureth Sulfate (Steol®CS-2301) 14.0

Jojoba Esters (Floresters™-154) 3.0


Procedure: Slowly add the VEEGUM Ultra to the water while mixing at maximum availableshear. Mix until fully hydrated. At reduced mixing speed, very slowly add the Part B ingredientsin the order shown, mixing after each addition until uniform. Add the Part C ingredients and

adjust as necessary to pH 5.5 ± 0.5.


2Rhodia Inc., Cranbury, NJ


4Floratech Americas, Chandler, AZ

TRADEMARKS


Amphosol and Steol are registered trademarks of Stepan Company.Floresters is a trademark of International Flora Technologies, Ltd.Mirataine is a registered trademark of Rhone-Poulenc, Inc.Tween is a registered trademark of Uniqema Americas LLC.

rev04/25/2013









Pearlescent Condit ioning Body Wash No. 488

Wt.%

AVEEGUM®


Water 61.25

B Mica (and) Titanium Dioxide (Timiron® MP-10011) 0.50

C

Sodium Laureth Sulfate (Steol® CS-2302) 25.00

Lauramide DEA (Incromide™7163) 7.50

Cocoyl Sarcosine 3.75


Procedure: Slowly add the VEEGUM Ultra to the water while mixing at maximum availableshear. Mix until fully hydrated. Add Part B and mix until uniform. At reduced mixing speed, addthe Part C ingredients in the order shown, mixing after each addition until uniform. Adjust asnecessary to pH 5.0 ± 0.5.

RAW MATERIAL SUPPLIERS1EMD Chemicals, Inc./RONA, Gibbstown, NJ



TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Incromide is a trademark of Croda, Inc.Steol is a registered trademark of Stepan Company.Timiron is a registered trademark of EM Industries, Incorporated.

rev04/25/2013









Body Wash Cream for Sensit ive Skin No. 505

Wt.%

AVEEGUM®


Water 63.0

BSodium Cocoyl Isothionate (Tauranol® I-781) 25.0

Cocamidopropyl hydroxysultaine (Mirataine® CBS2) 10.0


Procedure: While heating the water to 60-65oC, slowly add the VEEGUM Ultra while agitatingat maximum available shear. Continue mixing until fully hydrated. Maintaining temperature,slowly add Part B ingredients in the order shown, mixing after each addition until smooth anduniform. Cool while mixing to <45oC and then add Part C. Adjust as necessary to pH 5.5 ± 0.5.This formula can easily be converted to a body scrub by the incorporation of 5% polyethylenebeads.

RAW MATERIAL SUPPLIERS1Innospec Active Chemicals, Edison, NJ

2Rhodia, Cranbury, NJ

TRADEMARKS

VEEGUM is a registered trademark of R.T. Vanderbilt Holding Company, Inc. or itsrespective wholly owned subsidiaries.Mirataine is a registered trademark of Rhone-Poulenc, Inc.Tauranol is a registered trademark of Innospec Performance Chemicals Company.

rev04/25/2013





Vanderbilt Minerals, LLC, 33 Winfield Street, P.O. Box 5150, Norwalk, CT 06856-5150Telephone: (800) 562-2476 - Fax: (203) 855-1220 - Web Site: vanderbiltminerals.com



Conditioning Hair & Body Shampoo No. 499

Wt.%

AVEEGUM®


Water 60.0

B

Sodium Laureth Sulfate (Steol® CS-2301) 25.0

Cocamidopropyl Betaine (Amphosol® CA1) 9.0

Lauramide DEA (Incromide™ 7162) 3.0Citric Acid, 20% 1.0


Procedure: Slowly add the VEEGUM Ultra to the water while mixing at maximum availableshear. Mix until fully hydrated. At reduced mixing speed, very slowly add the Part B ingredients inthe order shown, mixing after each addition until uniform. Add the Part C ingredients and adjust

as necessary to pH 5.5 ± 0.5. This formula can easily be converted to a body scrub by theincorporation of 5% polyethylene beads.



TRADEMARKS


Amphosol and Steol are registered trademarks of Stepan Company.Incromide is a trademark of Croda, Inc.

rev04/25/2013









Aerosol Shave Cream fo r Sensi ti ve Sk in No. 503

Wt.%VEEGUM®


A VANZAN® NF, Xanthan Gum 0.3

Water 67.2


C

Stearic Acid XXX 3.0Coconut Acid 3.0Safflower Oil 0.2Soybean Oil 0.2

Cetyl Alcohol 1.0

Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs1) 1.0

Lanolin Alcohol 0.1

Isosorbide Laurate 1.0

Mineral Oil 3.0

D

Sodium Cocoyl Sarcosinate, 30% 10.0Panthenol 0.5

Aloe Vera 0.5

ETriethanolamine 1.5

Preservative, Fragrance q.s.

Procedure While heating the water to 75°C, slowly add the VEEGUM Ultra and VANZAN NFsequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Add the remaining water phase ingredients from Part B, mixing until uniform. Maintainthe water phase at 75°C. Blend the Part C oil phase ingredients and heat to 75°C. Add the oilphase to the water phase with good agitation; mix until uniform. Cool while mixing. Add the PartD ingredients when the emulsion is <40oC. Add the Part E ingredients when the emulsion is<35oC. Adjust as necessary to pH 7.5 ± 0.5.

RAW MATERIAL SUPPLIERS1Dow Corning Corporation, Midland, MI

TRADEMARKS


Xiameter is a registered trademark of Dow Corning Corporation. rev04/25/2013









Shaving Cream No. 501

Wt.%VEEGUM®

Ultra, Magnesium Aluminum Silicate 2.0 A VANZAN® NF, Xanthan Gum 0.5

Water 74.5

B

Cetyl Alcohol 0.5

Glyceryl Monostearate SE 3.0


C 12-15 Alkyl Benzoate (Finsolv® TN2) 3.0

Dimethicone (XIAMETER® PMX-200 Silicone Fluid 350cs3) 3.0

Lanolin Alcohol 1.0

Isosorbide Laurate 0.5Mineral Oil 5.0

C Sodium Lauroyl Sarcosinate, 30% 5.0

DTriethanolamine or Citric Acid (to pH 5.75±0.25) q.s.Preservative, Fragrance q.s.

Procedure: While heating the water to 75°C, slowly add the VEEGUM Ultra and VANZAN NFsequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Maintain the water phase at 75°C. Blend the Part B oil phase ingredients and heat to75°C. Add the oil phase to the water phase with good agitation; mix until uniform. Cool while

mixing. Add the Part C surfactant when the emulsion is <55o

C. Add the Part D ingredients whenthe emulsion is <35oC. Adjust as necessary to pH 5.75 ± 0.25.




TRADEMARKS

VEEGUM and VANZAN are registered trademarks of R.T. Vanderbilt HoldingCompany, Inc. and/or its respective wholly owned subsidiaries.Finsolv is a registered trademark of Innospec Performance Chemicals Company.Neobee is a registered trademark of Stepan Company.Xiameter is a registered trademark of Dow Corning Corporation.

rev04/25/2013









Waterless Skin Scrub w ith D-Limonene No. 479

Wt.%

AVEEGUM®

Ultra, Magnesium Aluminum Silicate 2.0VANZAN® NF, Xanthan Gum 0.6Water 51.7

B

Oleic Acid 10.0Mineral Oil 10.0Cetyl Alcohol 1.0Isosorbide Laurate 1.0Lanolin 1.0

C

Water 2.0

Potassium Hydroxide 0.7

D D-Limonene 10.0

E Polyethylene Beads (A-C 9-A1) 10.0

F Preservative, Fragrance q.s.

Procedure: While heating the water to 75°C, slowly add the VEEGUM Ultra and VANZAN NFsequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Maintain the water phase at 75°C. Blend the Part B oil phase ingredients and heat to75°C. Add the oil phase to the water phase with good agitation; mix until uniform. Cool while

mixing. Add the Part C solution of potassium hydroxide in water when the emulsion is 45oC.Continue to cool while mixing and add Parts D, E and F when the emulsion is <35oC.

RAW MATERIAL SUPPLIERS1Honeywell Specialty Wax & Additives,

Morristown, NJ

TRADEMARKS


rev04/25/2013



efore using, read, understand and comply with the information and precautions in all applicable Safety Data Sheets, labels and other product literature.





Waterless Hand Cleaner with Abrasive No. 477

Wt.%

AVEEGUM®

Ultra, Magnesium Aluminum Silicate 1.5VANZAN® NF, Xanthan Gum 0.5Water 42.3

BOleic Acid 9.0Mineral Oil 9.0

CWater 2.0

Potassium Hydroxide 0.7

D C11-12 Isoparaffin (Isopar ® K1) 25.0

E Polyethylene Beads (A-C 9-A2) 10.0

F Preservative, Fragrance q.s.

Procedure: While heating the water to 75°C, slowly add the VEEGUM Ultra and VANZAN NFsequentially or as a dry blend to the water agitated at maximum available shear. Mix until fullyhydrated. Maintain the water phase at 75°C. Blend the Part B oil phase ingredients and heat to75°C. Add the oil phase to the water phase with good agitation; mix until uniform. Cool whilemixing. Add the Part C solution of potassium hydroxide in water when the emulsion is 45oC.Continue to cool while mixing and add Parts D, E and F when the emulsion is <35oC.

RAW MATERIAL SUPPLIERS1ExxonMobil Chemical, Houston, TX

2Honeywell Specialty Wax & Additives,

Morristown, NJ

TRADEMARKSVEEGUM and VANZAN are registered trademarks of R.T. Vanderbilt HoldingCompany, Inc. and/or its respective wholly owned subsidiaries.Isopar is a registered trademark of Exxon Mobil Corporation.

rev04/25/2013

Documents

923 VEEGUM Ultra Mosquito