8/10mm SLIDING DOOR AND SIDE PANELRefer To Sheet 15 For Relevant Product Codes

VictoriaPlum.com0344 804 48 48

C hange the hand by turning moving panel inside out & top rail upside down.

This product is universal, not handed

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION

1) General Information

2) Additional Notes

Please inspect this product upon delivery, any missing parts or manufacturing

defects must be reported immediately to the supplier. Damage or defects reported

later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID

HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.

Glass breakage claims will not be accepted after the product has been unpacked.

Please note: Aluminium is a soft metal, and undergoes a series of extrusion,

fabrication, polishing and anodising processes in order to create your finished

shower enclosure. Some light surface marks are normal, and is a result of the

manufacturing processes. Quality control has ensured that this item is of a good

standard, and is fit for purpose.

Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: this product is heavy and may require two people to install.

This product is heavy and may require two people to install.

TOOLS REQUIRED

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Mallet

Silicone Sealant

PZ1

1

3

THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.

ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber

FITTED SLIDING DOOR AND SIDE PANEL DRAWING

Installation Steps

101200/1400/1600/1700

10

10

1 01 0

10

80

0/9

00

1010

10

1010

22

ASSEMBLY INSTRUCTIONS - DRAWING

(10)

(8)

(7)

(5)(4)(3)

(2)

(1)

(6)

(9)

(11)

(12)

(13)

(14) (15) (16) (17) (18)

(31)

(19) (20) (21) (23)

(25)

(26)

(28)

(29)

(30)

(33)(34)(35)(36)(37)(38)(32)

(24)

(1) 1x Guide Rail Seal(2) 1x Door Stop Cap(3) 1x Cover Cap (Guide Rail)(4) 1x Wall Post Cover Cap A(5) 1x Guide Rail(6) 10x Wall Plugs (7) 10x Screws 4x30(8) 1x Wall Profile A(9) 1x Wedge Gasket Seal(10) 1x Fixed Panel(11) 1x Fixed Panel Seal(12) 1x Handle B (10mm Product In Carton)(13) 1x Handle A (8mm Supplied Separately)(14) 2 Bottom Guide Blocks Part B (L+R) x (15) 1 Bottom Guide Blocks Part A x (16) 1x Drip Strip

(18) 2x Drip Strip End Cap (L+R)(19) 1x Wall Profile B

(17) 1x Moving Panel

(31) 2x Inner Washer(30) 1x Outer Washer(29) 2x Screws M5x20 (Sink Head)(28) 1x Cover Cap (Guide Rail)

(25) 1x Wedge Gasket Seal(26) Wall Profile1x

(24) 1x Fixed Panel (23) 1x Seal A(22) 4x Screws 4x16

(20) 1x Seal B

(32) 1x Wall Fixing Seat(33) 1x Adjustment Bracket(34) 4x Bump Stops(35) 2x Rollers(36) 2x Screw Caps(37) 2x Screws(38) 2x Glass-Fitting Parts

SIDEPANEL BOX

(22)

(21) 6x PVC Hoses

(27)

(27) 1x Wall Post Cover Cap B

4

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS

SHOWER PANEL / DOOR

Step 2 FITTING FIXED PANEL

6mm x4

x44x30

1

x44

3

5

x42

10mm

1

2

Step 1 DRILLING WALL PROFILE TO THE WALL SLIDING DOOR RECESS INSTALLATION

5

Step 3 ASSEMBLING THE GUIDE RAIL AND MARKING THE WALL

Step 4 TAKE APART THE GUIDE RAIL

1

3

5

1

2

4

2 x2

x2

6

Step 5 SECURING THE WALL FIXING SEAT

Step 6 SLIDE GUIDE RAIL ON TO THE WALL FIXING SEAT

Ø6mm

2

3 4

1

3

4

7

2

1

MAX:20mm

6

MAX:20mm

5

x2

x2

x2

x2

1

H2O

2

3

5

6

748mm glass

2

10mm glass

7

inside

Step 7 FITTING THE WEDGE GASKET SEAL

Step 8 FITTING THE BOTTOM DRIP STRIP

Step 9 FITTING THE ROLLERS

1

2

3

4

5

6

8

x2

x2

x2

View from inside

1

2

3

4

Step 10 FITTING THE SEAL AND ADJUST DOOR STOP

Adjust

9

Step 11 ADJUSTING THE MOVING PANEL

OUTSIDE

OUTSIDE

4x30

x4

x4

6mm

x4

2

1 5

x4

4

6

3 x47

Step 12 INSTALLING THE WALL PROFILE

10

Step 14 SILICONE THE OUTSIDE EDGES

Step 13 FITTING THE TOP CAP AND SEAL AND FITTING THE HANDLE

INSIDE

INSIDE

10mm glass

8mm glass

Allow 24 hours for silicone to dry before use. Silicone on the

outside edge only, NOT THE INSIDE

11

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS

SHOWER PANEL / DOOR

Step 1 DRILLING WALL PROFILE TO THE WALL

6mm x8

x8

x8

4x30

x84

2

5

3

10mm

CORNER INSTALLATION WITH A SIDE PANEL

Step 2 ASSEMBLING THE FIXED PANELS, WASHER, COVER CAP AND WEDGE GASKETS

x2

x2

x23

4

2

x2

x2

x2

1

5

6

H2O

MAX:20MM

7

8

9

12

Step 3 FITTING THE BOTTOM DRIP STRIP

3

48mm glass

2 5

6

7

10mm glass

Step 4 FITTING THE ROLLERS

1

2

3

4

5

6

x2

x2

x2

View from inside

1

2

3

4

Step 5 FITTING THE SEAL AND ADJUSTING DOOR STOP

Adjust

Step 6 ADJUSTING THE MOVING PANEL

OUTSIDE

OUTSIDE

13

14

Step 8 SILICONE THE OUTSIDE EDGES

Step 7 SECURING THE PROFILE AND COVER SEAL AND FITTING THE TOP CAP

2

1 4

3

5 x4

x4 6

Allow 24 hours for silicone to dry before use. Silicone on the

outside edge only, NOT THE INSIDE

Product name: 8/10mm Sliding Door And Side Panel

Product code: DSD1202 / DSD1402 / DSD1602 / DSD1702 DSD1203F / DSD1203M

Customer help line number: 0344 804 48 48

CARE AND MAINTENANCE

COMMITMENT TO QUALITY

1) AFTER CARE INSTRUCTIONS

2) MAINTENANCE

Regularly clean your shower product with warm soapy water

Clean the plastic parts with a cloth and mild detergent. Never

use any abrasive creams, dissolvents, acetone or detergents

and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained

in these instructions. The supplier reserves the right to introduce

technical changes without notice.

It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you

firstly contact a competent plumber. However we understand that

this may not always be the case, so should you experience

any problems please contact our customer services quoting

the following:

to prevent lime scale build up. Do not use abrasive cleaning

fluids or materials, or strong chemical cleaners as this will

damage the product surface.

DSP802 / DSP902 / DSP803 / DSP903

15

INSTALLERS NOTES

16

INSTALLERS NOTES

17

INSTALLERS NOTES

18

The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.

We suggest you take it to the local landfill site and discard in the designated bins.

V02/08/2017

Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG

Park

17

EN 14428:2015

DOP No.:J170320003-1

Shower enclosures with aluminiumprofiles and safety glass

Essentialcharacteristics

Performance Harmonisedtechnical

specificationCleanability

Impactresistance/shatter

properties

Pass

Pass

PassDurability

Clause 4.2 of EN 14428:2015

Clause 4.3 of EN 14428:2015

Clause 4.4 of EN 14428:2015