Upload
johnsondon
View
222
Download
4
Tags:
Embed Size (px)
Citation preview
802.11b+g Wireless LAN
USB Adapter
User Manual
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interface, and 2) This device must accept any interface received, including interface that may
cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
◗ Reorient or relocate the receiving antenna. ◗ Increase the distance between the equipment and receiver. ◗ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
CAUTION: 1) To comply with FCC RF exposure compliance requirements, a separation
distance of at least 20 cm must be maintained between the antenna of this device and all persons.
2) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Table of Contents
INTRODUCTION ...................................................................................................1
FEATURES ................................................................................................. 1 INSTALLATION ....................................................................................................2
STEP 1: INSTALL THE DRIVER & UTILITY ................................................. 2 STEP 2: INSTALL THE DEVICE ................................................................... 5
NETWORK CONNECTION .................................................................................9
IN WINDOWS 98SE/ME ............................................................................ 9 IN WINDOWS 2000/XP............................................................................ 12 IP ADDRESS............................................................................................ 14
Configuration Utility .............................................................................................15
STATUS ................................................................................................... 16 BASIC SETTING ....................................................................................... 18 SECURITY ............................................................................................... 23 ADVANCED SETTING............................................................................... 25 INFORMATION ......................................................................................... 28
- 1 -
INTRODUCTION
The 802.11b+g Wireless LAN USB Adapter is designed for a USB type A port of a laptop or desktop computer for creating a wireless workstation. It is USB 2.0 compliant which connects to any available USB port on a notebook or desktop computer.
The 802.11b+g Wireless LAN USB Adapter complies with IEEE 802.11g standard that offers a data rate up to 54Mbps in a wireless LAN environment. It is backward compliant with IEEE 802.11b specification. The high-speed wireless network card can plug into your notebook or desktop PC and accesses to the LAN or peer-to-peer networking easily without wires or cables. Whether you’re at your desk or in the boardroom, it allows you to share printers, files, and other network resources.
Features
Complies with IEEE 802.11g standard for 2.4GHz Wireless LAN USB 2.0 compliant USB Plug & Play Interoperable with existing network infrastructure Secure information transmission Freedom to roam while staying connected Compatible with specialty wireless products and services Up to 54 Mbps data rate Antenna is built in the card with LED indication Low power consumption Easy to install and configure
- 2 -
INSTALLATION
Step 1: Install the Driver & Utility
Caution!
Do not insert the wireless LAN card into your computer until the procedures in “ Install the Driver& Utility” have been performed.
1. Exit all Windows programs. Insert the included CD-ROM into your computer. The CD-ROM will run automatically.
2. When the Main Menu screen appears, click “ Driver & Utility Installation” to continue.
3. When the Welcome screen appears, click Next to continue.
4. The installation program will start running automatically. Follow the on-screen instruction to proceed.
- 3 -
- 4 -
Note for Windows 2000 users
When the “Digital Signature Not Found” screen appears, click “Yes”
to continue.
Note for Windows XP users:
When the following screen appears, click “Continue Anyway” to
continue.
- 5 -
Step 2: Install the Device
Note: Before you install the device to your computer, make sure you
have installed the driver and utility as described in the previous section.
1. Locate your USB host and insert the USB Adapter.
2. Once the device has been inserted to your computer, Windows will detect the new hardware.
3. Windows will begin copying the files to your computer.
Note for Windows 98SE users:
1. Before installing the device, make sure you have your original
Windows 98 CD-ROM at hand.
2. When the “Please insert the disk labeled ‘Windows 98 Second
Edition CD-ROM, and then click OK” window appears, insert
the CD-ROM as requested. Click OK.
- 6 -
Note for Windows 2000 users:
When the “Digital Signature Not Found” screen appears, click “Yes”
to continue.
Note for Windows XP users:
When the following screen appears, select “Install the software
automatically (Recommended)” to continue.
When the following screen appears, select “Continue Anyway” to
continue.
- 7 -
- 8 -
Verify
To verify if the device exists in your computer and is enabled, go to Start Settings Control Panel System ( Hardware) Device
Manager. Expand the Network Adapters category. If the 802.11b+g USB Wireless LAN Adapter is listed here, it means that your device is properly installed and enabled.
- 9 -
NETWORK CONNECTION
Once the device driver is well installed, a network setting described in the following should be also established.
In Windows 98SE/ME 1. Go to Start Settings Control Panel Network.
2. Make sure that all the required components are installed. If any components are missing, click on the Add button to add them in.
- 10 -
3. For making your computer visible on the network, enable the File and Print Sharing.
4. Click the Identification tab. Make up a name that is unique from the
other computers' names on the network. Type the name of your workgroup, which should be the same used by all of the other PCs on the network.
5. Click the Access Control tab. Make sure that “Share-level access
control” is selected. If connecting to a Netware server, share level can be set to “User-level access control.”
6. When finished, restart your computer to activate the new device.
- 11 -
In Windows 2000/XP 1. (In Windows 2000)
Go to Start Settings Control Panel Network and Dial-up Connections Local Area Connection Properties.
(In Windows XP) Go to Start Control Panel Network and Internet Connections Network Connection Wireless Network Connection Enabled USB Wireless Network Adapter.
- 12 -
2. Make sure that all the required components are installed.
3. If any components are missing, click on the Install… button to select the Client/Service/Protocol required. After selecting the component you need, click Add… to add it in.
4. For making your computer visible on the network, make sure you have installed File and Printer Sharing for Microsoft Networks.
- 13 -
- 14 -
IP Address
Note: When assigning IP Addresses to the computers on the network, remember to have the IP address for each computer set on the same subnet mask. If your Broadband Router use DHCP technology, however, it won’t be necessary for you to assign Static IP Address for your computer.
To configure a dynamic IP address (i.e.
if your broadband Router has the
DHCP technology), check the Obtain
an IP Address Automatically option.
To configure a fixed IP address (if you
broadband Router is not DHCP supported,
or when you need to assign a static IP
address), check the Use the following IP
address option. Then, enter an IP address
into the empty field, for example, enter
192.168.1.1 in the IP address field, and
255.255.255.0 for the Subnet Mask.
- 15 -
Configuration Utility After the Wireless adapter has been successfully installed, users can use the included Configuration Utility to set their preference.
Go to Start Program 802.11b+g Wireless LAN 802.11b+g USB Wireless LAN Utility
For Windows 2000/XP, the Configuration Utility icon will also appear in the taskbar. You can open the Configuration Utility by clicking the icon.
- 16 -
Status
The Status Screen displays the current status of the Wireless USB Adapter.
Item Description
Channel Shows the selected channel that is currently in use. (There are 14 channels available, depending on the country.)
Type
The infrastructure is intended for the connection between wireless network cards and an Access Point. With the wireless adapter, you can connect wireless LAN to a wired global network via an Access Point
The Ad-hoc lets you set a small wireless workgroup
Item Description
- 17 -
easily and quickly. Equipped with the wireless adapter, you can share files and printers between each PC and laptop.
Tx Rate Click the down arrow ▼ to select the Tx Rate from Auto, 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54 Mbps, you can select up to 54 Mbps.
SSID
The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network.
It shows the current SSID setting of the Wireless USB Adapter.
Encrypt WEP is a data privacy mechanism based on a 64-bit/128-bit shared key algorithm.
Link Status
Displays the information about the status of the communication between the Wireless USB Adapter and the Access Point.
Signal Strength
Displays the signal strength of the connection between the Wireless USB Adapter and the Access Point it connects.
Link Quality
Displays the link quality of the connection between the Wireless USB Adapter and the Access Point it connects.
Tx Frame The quantities for the wireless network card transmit.
(Frame: The unit of packet)
Rx Frame The quantities for the wireless network card receive.
(Frame: The unit of packet)
- 18 -
Basic Setting
The Basic Setting Screen displays General Connection Setting and Profile.
I. General Connection Setting
Item Description
Channel The Channel will change automatically according to AP’s setting.
Tx Rate Click the down arrow ▼ to select the Tx Rate from Auto, 1, 2, 5.5, 11, 6, 9, 12, 18, 24, 36, 48, 54 Mbps, you can select up to 54 Mbps.
- 19 -
SSID The SSID is the unique name shared among all points in your wireless network. The name must be identical for all devices and points attempting to connect to the same network.
Any
You may select to have SSID by choosing any, the SSID will be obtained automatically from whichever Access Point with the optimal signal for this device. If any is left unchecked, it means you will have to enter the SSID manually.
Network Type
The infrastructure is intended for the connection between wireless network cards and an Access Point. With the wireless adapter, you can connect wireless LAN to a wired global network via an Access Point
The Ad-hoc lets you set a small wireless workgroup easily and quickly. Equipped with the wireless adapter, you can share files and printers between each PC and laptop.
- 20 -
- 21 -
Authentication Mode
The authentication mode defines configuration options for the sharing of wireless networks to verify identity and access privileges of roaming wireless network cards.
You may choose between Open System, Shared Key, Auto, and WPA-PSK.
Open System: If the Access Point is using "Open System" authentication, then the wireless adapter will need to be set to the same authentication type.
Shared Key: Shared Key is when both the sender and the recipient share a secret key.
Auto: Select Auto for the USB adapter to select the Authentication type automatically depending on the Access Point Authentication type.
WPA-PSK: It is one mode of Wi-Fi security and gives 2 methods of encryption, TKIP and AES. Select TKIP or AES according to the settings of the Access Point.
Encryption
WEP is a data privacy mechanism based on a 64-bit/128-bit shared key algorithm. Press the down arrow▼, you can choose to have WEP Disabled or Enabled.
If the authentication mode is set to WPA-PSK, the encryption type can be chosen from WPA-TKIP and WPA-AES. Check the settings of the Access Point..
Change
or
Apply
You may change the above settings by clicking Change.
Press Apply when you have done the change and want to save the settings. .
- 22 -
II. Profile
1. Load (profile setting):
You may select already saved file from the "Profile name" list, and
then press "Load ". The setting status will then be restored.
2. Save current (setting to profile):
You may save current setting to profile and add one new item in
"Profile name".
3. Delete
Delete the files in the “Profile name”.
- 23 -
Security
You can only set your Security preference when Change is selected and then all fields are active for change. To save settings, press Apply when you are done with the settings.
Item Description
Key length You may select the key length between 64 (bit) and 128 (bit).
Default Key ID You can set your default key ID at #1~#4 as set in the following field.
Key Format
Select Hexadecimal if you are using hexadecimal numbers (0-9, or A-F).
Select ASCII if you are using ASCII characters
(case-sensitive).
Ten hexadecimal digits or five ASCII characters are
- 24 -
needed if 64-bit WEP is used; 26 hexadecimaldigits or 13 ASCII characters are needed if 128-bitWEP is used.
Key Value:
#1~#4
This setting is the configuration key used in accessing the wireless network via WEP encryption. You can specify up to 4 different keys to encrypt or decrypt wireless data.
PSK
With PSK (Pre-Shared Key) authentication, only those PCs that possess the correct authentication key can join the network. PSK can be 8 to 64 bytes depending on the Access Point.
- 25 -
Advanced Setting
The Advanced Setting Screen shows you to change advanced configuration, such as Fragmentation Threshold, RTS/CTS Threshold and Power Consumption Setting.
Item Description
Fragmentation Threshold
The mechanism of Fragmentation Threshold is used to improve the efficiency when high traffic flows along in the wireless network. If your 802. Wireless LAN Adapter often transmit large files in wireless network, you can enter
Item Description
- 26 -
new Fragment Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346.
RTS/CTS Threshold
RTS/CTS Threshold is a mechanism implemented to prevent the “Hidden Node” problem. If the “Hidden Node” problem is an issue, users have to specify the packet size. The RTS/CTS mechanism will be activated if the data size exceeds the value you set.. The default value is 2347.
This value should remain at its default setting of 2347. Should you encounter inconsistent data flow, only minor modifications of this value are recommended.
Power Consumption Setting
Continuous Access Mode (CAM)
When this mode is selected, the power supply will be normally provided even when there is no throughput.
Maximum Power Saving Mode
When this mode is selected, this device will stay in power saving mode even when there is high volume of throughput.
Item Description
- 27 -
Fast Power Saving Mode
When this mode is selected, the power mode will switch between CAM and Maximum Power-Saving Mode depending on the volume of throughput. The device driver checks the total bytes (only data frame) every 4 seconds to decide the power mode. If the total bytes sent exceed 10k bytes, the device driver will choose “CAM”. If the total bytes are less than 10k bytes, however, the device driver will choose “Maximum Power-Saving Mode”.
- 28 -
Information
Click Info Tab to view basic information about the Utility like the Driver Version, Utility Version, and MAC Address. Press the OK button to exit the application.