721X owner ops - Lastecgateway.lastec.com/manuals/Parts/721xmas.pdf · Chapter 10: Parts Manual LasTec Articulator Owner Manual Parts Index Model 721X 10-6 Parts Index Listed By Part

10-1

Chapter Ten: Master Parts Manual

LasTec ArticulatorModel 721X

Master Parts Manual

Manual Part Number: Man-721X

LasTecA Division of Wood-Mizer Products, Inc.

7865 N County Rd 100ELizton, Indiana 46149

Phone (317) 892-4444 Fax (317) 892-4188www.lastec.com

Chapter 10: Parts Manual LasTec Articulator Owner ManualParts Index Model 721X

10-2

LasTec Articulator Owner Manual Chapter 10: Parts ManualModel 721X Parts Index

10-3

How To Use This Parts Manual

Fig. 2.01 Assembly IllustrationSerial Number

From 1010392 1080492 2651292 7570694 8160894 8781194To 1070392 2641292 7560694 8150894 8771194 Present

Ref No. Part No. Part No. Part No. Part No. Part No. Part No. Part Description1 F120 F120 F120 F120 F120 F120 1"-8 Nylock Nut2 F168 (*1) F168 (*1) F168 (*1) F168 F168 F168 1" SAE Flat Washer3 P109 P109 P109 P109 P109 P109 Bronze Bushing, 1" ID4 Not Used Not Used Not Used P247 Not Used Not Used 90 Degree Street Elbow, 1/2" NPT5 W134 W134 W134 W134 Gearbox Channel Weldment, HCM66/SGCM500

W206 W206 Gearbox Channel Weldment , CM413A6 F121 F121 F121 F121 F121 F121 Bolt, 1/2-13 x 1 1/4"7 F122 F122 F122 F122 F122 F122 1/2" Split Lock Washer8 P196-M (*2) P196-M (*2) P196-M P196-M (*3) P196-M (*4) Gearbox, HCM66SCR12, StBv, Splined

P300 Gearbox, SGCM500SAR21, SpBv, Splined9 L128-M (*5) L128-M (*5) L128-M (*5) L128-M (*5) L128-M (*5) L128-M Gearbox Swivel Cover, Universal10 P171 Drive Pulley, Single Groove, BK140H

P130 P130 P130 P130 P130 Drive Pulley, Double Groove, 2BK140H11 P131 (*6) P131 (*6) P131 (*6) P131 (*6) P131 (*6) Split Taper Bushing, 1 1/4" ID x H

P281 (*6) Split Taper Bushing, 1 3/8" ID x H12 F187 F187 F187 F187 F187 F187 Bolt, HH, 1/4-20 x 3/4", G813 P208 (*7) P208 (*7) P208 (*8) P208 (*8) P208 (*8) Pillow Block Bearing, 1 1/4" ID, SSC

P282 (*8) Pillow Block Bearing, 1 3/8" ID, SSC14 F178 F178 F178 F178 F178 F178 Set Screw, 5/16-24 x 5/16", Nylock15 P108 (*9) P108 (*9) Grease Zerk, 1/8" NPT, Straight

P107 P107 P107 P107 Grease Zerk, 1/4-28, Straight16 W135 W135 W135 W135 Slide Bar Weldment - HCM66SCR12

W205 W205 Slide Bar Weldment - CM413A17 P107 P107 P107 P107 P107 P107 Grease Zerk, 1/4-28, Straight18 P146 P146 P146 P146 P146 P146 Drive Belt, B-49 Insta-Power

(*1) Originally P115 & P116 Brass & Zinc Wear Washers, have been replaced with F168 1" SAE Flat Washers. P115 & P116 are nolonger available.

NOTE: The location of these washers may vary depending on model.

(*2) Originally P129-M Gearbox, which utilized the P148 PTO Shaft, which are both no longer available. If converting from a P129-M toa P196-M, you will also need to order either a P225 PTO Shaft or a P207 Splined Yoke to upfit your existing PTO shaft.

(*3) Originally P220 Gearbox, has been replaced with the P196-M Gearbox. The P220 is no longer available. If converting from a P220to a P196-M, you will also need to order (1) W134 Gearbox Channel Weldment and (1) W135 Slide Bar Weldment.

(*4) Originally P250 Gearbox, has been replaced with the P196-M The P250 is no longer available. If converting from a P250 to aP196-M you will also need to order (1) W134 Gearbox Channel Weldment and (1) W135 Slide Bar Weldment.

(*5) Originally L109-M Swivel Cover, has been replaced with the P128-M Universal Swivel Cover. The L109-M is no longer available.

(*6) P131 & P281 each include (2) F187 1/4-20 x 3/4" G8 Bolts.

(*7) Originally P132 Pillow Block with Eccentric Lock Collar. If converting to P208, new mounting hardware will also be needed. (SeeFig. 2.03 for listing.) Also, P208 includes (1) F178 5/16-24 x 5/16" Nylock Set Screw and (1) P107 1/4-28 Straight Grease Zerk.

(*8) P208 Includes (1) F178 5/16-24 x 5/16" Nylock Set Screw and (1) P107 1/4-28 Straight Grease Zerk.

(*9) Used only with P132 Pillow Block Bearing.

For your convenience, we have compiled two indexes of all illustrated Articulator parts and the illustration(s) inwhich they appear. These indexes are contained in the following section of this manual. The first index of parts islisted in order by part number, followed by an index of parts listed in order by part description. Simply locate thepart number or description in either index, and turn to the corresponding illustration number(s) to view the part forphysical verification and/or actual application(s).

Part NumbersThis is the part number you should

use when ordering the part.

Not UsedIf, due to an engineering change, an

illustrated part is discontinued orreplaced, the term “Not Used”

appears in the column under theappropriate serial numbers.

FootnotesChanges which may include important information have

footnotes (*1) listed next to the corresponding part number.Please be sure to read and understand these notes, as they willaid you in identifying and ordering the correct parts for the serial

number series of your Articulator.

Part DescriptionThis is the part description you

should use when ordering the part.

Reference NumbersParts shown in the corresponding

Illustration will each post a referencenumber. Find this reference number

on the spreadsheet for properinformation about that part.

Serial NumbersEngineering changes made to the Articulator aretracked by serial number. If a change affects a

part in the illustration, serial number breakdownsindicating when the change was implemented are

listed at the top of the spreadsheet. Assembly IllustrationThis references the proper

illustration which corresponds withthe spreadsheet

Go to www.lastec.com for latest changes in this manual.


10-4



10-5

Parts IndexListed By Part Number

Part No. Part Description Illustration Number(s)

018008 Decal, Die-Cut, "LasTec" XM-3.07 XM-3.14018009 Decal, Die-Cut, "Articulator" XM-3.07 XM-3.14018309 Spindle, Extended XM-3.01 XM-3.01A019662 Gearbox Bearing Cup XM-2.02019663 Gearbox Bearing XM-2.02028350 Washer, Nylon Blade XM-3.01A029096 Pivot Pin Weldment XM-1.01040231 Deck Weldment, X1, DBS XM-3.06040232 Deck Weldment, X2, DBS XM-3.06040233 Deck Weldment, X3, DBS XM-3.06040234 Deck Weldment, X4, DBS XM-3.06040235 Deck Weldment, X5, DBS XM-3.06040236 Deck Weldment, X6, DBS XM-3.06040237 Deck Weldment, X7, DBS XM-3.06040249 Kit, Slide Bar Hardware Upfit XM-3.02040250 Kit, Nylon Blade XM-3.01AA149 Wheel/Rim Assembly, UF XM-4.09A150 Wheel Assembly, 9” x 3.5”, UF XM-4.06 XM-4.07 XM-4.08 XM-4.09A235 Cable Assembly, X1/X3 XM-5.06A236 Cable Assembly, X2 XM-5.06A240 Wheel Height Gauge Assembly XM-4.11A241 Gas Spring Cylinder Assembly XM-5.01A250 Wheel Assembly, 13 x 5, UF XM-4.01A324 Cable Assembly, 521X, 34” XM-3.12C377 Cable Retainer Spacer Tube XM-5.06C413 Clamping Plate, Side XM-3.04C444 Cylinder Tie Rod XM-5.01C489 Axle, Drilled XM-4.03 XM-4.05C506 Clamping Plate, Top XM-3.04C510 Cover, Pivot Arm, Deck X1/X3 XM-3.08C527 Cylinder Tie Rod, 3/4" XM-5.02 XM-5.03C529 Chain, Safety, 100” XM-3.11C544 Pull Bar L-Pin XM-1.02C546 Chain Mount Plate, Safety XM-3.11C547 Chain, Safety, 78” XM-3.11C549 Cable Mount Plate XM-3.12C550 Cable, 521X, 34” XM-3.12C554 Trim, Rubber, 9 1/2" XM-3.08C575 Anti-Scalp Roller Tube XM-4.10C576 Retro Anti-Scalp Roller Tube XM-4.10

F04203-11 Rivet, 3/16" x 1/4" XM-3.08F05004-111 Stud, Press-In, 1/2-20 x 1 13/16" XM-4.03 XM-4.05F05004-112 Stud, Press-In, 5/16-24 x 3/4" XM-4.09F05004-132 Bolt, 1-8 x 5", G8 XM-3.03F05004-154 Bolt, 1-8 x 4", G8 XM-3.02F05004-155 Bolt, 1-8 x 4 1/2", G8 XM-3.03F05005-101 Bolt, 1/4-20 x 1" XM-4.09F05005-118 Screw, SFH, 1/4-20 x 1" XM-3.08F05005-119 Bolt, AH, 1/4-20 x 1 3/4", SS XM-4.01 XM-4.03 XM-4.05F05005-120 Bolt, AH, 1/4-20 x 1", SS XM-4.01 XM-4.03 XM-4.05 XM-4.05F05005-121 Bolt, AH, 1/4-20 x 1 1/4", SS XM-4.01 XM-4.03 XM-4.05F05005-122 Bolt, AH, 1/4-20 x 1 1/2", SS XM-4.01 XM-4.03 XM-4.05F05006-1 Bolt, 5/16-18 x 1" XM-2.01 XM-3.08 XM-3.09 XM-3.10 XM-3.10F05006-5 Bolt, 5/16-18 x 3/4” XM-3.08 XM-3.09 XM-3.09F05006-83 Bolt, Eye, 5/16-18 x 1 1/4” XM-3.12

F05007-135 Bolt, 3/8-16 x 3 1/4" XM-5.06F05007-27 Bolt, 3/8-16 x 3/4” XM-1.01

F05008-106 Bolt, 1/2-13 x 4 3/4” XM-4.10F05008-37 Bolt, 1/2-13 x 1 1/4" XM-2.01F05008-95 Bolt, 5/8-18 x 1 1/4" XM-3.01 XM-3.01AF05009-36 Bolt, 3/4-10 x 3" XM-1.02 XM-3.04 XM-4.04F05009-44 Bolt, 3/4-10 x 2 1/2” XM-4.04F05009-54 Bolt, 3/4-10 x 3 1/2" XM-3.04F05009-60 Bolt, 7/16-14 x 1 3/4", G8 XM-3.05



10-6



F05009-62 Bolt, 5/16-18 x 1 1/4" XM-5.06F05009-66 Bolt, 1/2-13 x 2 3/4", G8 XM-2.03F05009-67 Bolt, 1/4-20 x 3/4 ", G8 XM-2.01F05009-69 Bolt, 1-8 x 3", G8 XM-1.02 XM-3.02 XM-4.04F05009-70 Bolt, 5/16-18 x 1 3/4" XM-5.06F05009-71 Bolt, AH, 1/4-20 x 5/8", SS XM-4.01 XM-4.03 XM-4.05F05009-75 Screw, Wing, 1/4-20 x 1/2" XM-4.11F05009-76 Eye Bolt, 1/2-13 x 2" XM-5.06F05009-77 Screw, Wing, 3/8-16 x 5/8" XM-3.08F05009-79 Bolt, 5/16-18 x 2", G8 XM-5.06F05009-80 Bolt, 5/8-18 x 2 1/4" XM-3.01 XM-3.01AF05010-10 Nut, Nylock, 3/8-16 XM-3.08 XM-3.08 XM-5.06

F05010-103 Nut, Nylock, 3/4-10 XM-1.02 XM-3.04 XM-4.06 XM-4.07F05010-103 Nut, Nylock, 3/4-10 XM-4.02F05010-104 Nut, Jam, 3/4-10 XM-3.02 XM-3.03 XM-3.04F05010-109 Nut, Nylock, 1-8 XM-2.01 XM-3.03 XM-4.04 XM-5.03F05010-122 Nut, Nylock, 3/4-10 XM-3.02 XM-4.08F05010-127 Nut, Half Nylock, 1/2-13 XM-4.10F05010-135 Nut, Nylock, 7/16-14 XM-3.05F05010-139 Nut, Hex, 7/8-14 XM-3.01 XM-3.01MF05010-142 Nut, Lug, 5/16-24 Tapered XM-4.09F05010-147 Nut, Hex, 9/16-12 XM-5.06F05010-149 Nut, Nylock, 5/16-24 XM-5.06F05010-161 Nut, 2-Way Locking Jam, 3/4-10 XM-3.02F05010-17 Nut, Hex, 5/16-18 XM-3.12F05010-24 Nut, Wing, 3/8-16 XM-3.08F05010-35 Nut, Hex, 1/2-13 XM-5.06F05010-58 Nut, Nylock, 5/16-18 XM-3.08 XM-3.10 XM-3.10 XM-3.12 XM-5.06 XM-5.06F05010-63 Nut, Hex, 1/4-20 XM-4.09F05010-69 Nut, Nylock, 1/4-20 XM-3.08F05010-7 Nut, Hex, 3/4-10 XM-3.02 XM-3.03 XM-3.04 XM-4.04 XM-5.01F05010-8 Nut, Nylock, 1/2-13 XM-2.03 XM-3.05 XM-4.01 XM-4.03 XM-4.05 XM-5.06F05010-9 Nut, Keps, 1/4-20 XM-4.01 XM-4.03 XM-4.05

F05011-105 Washer, Fender, 5/16” x 1/8” XM-3.09 XM-3.10F05011-11 Washer, Flat, 1/4" SAE XM-3.08 XM-4.05F05011-14 Washer, Split Lock, 1/4" XM-4.09F05011-16 Washer, Flat, 5/16" XM-2.01 XM-3.10 XM-3.10 XM-3.12 XM-5.06F05011-17 Washer, Flat, 5/16” SAE XM-3.08 XM-3.08 XM-5.06F05011-2 Washer, Flat, 1/2" SAE XM-2.03 XM-4.01 XM-4.03 XM-4.05F05011-27 Washer, Split Lock, 5/8" XM-3.01 XM-3.01AF05011-29 Washer, Flat, 3/4" XM-1.02F05011-4 Washer, 3/8” XM-1.01F05011-40 Washer, Flat, 5/8" XM-3.01AF05011-43 Washer, Flat, 7/16" SAE XM-3.05F05011-44 Washer, Fender, 3/8" XM-3.08F05011-46 Washer, Split Lock, 7/8" XM-3.01 XM-3.01AF05011-50 Washer, Fender, 5/16” XM-3.10F05011-53 Washer, Split Lock, 1" XM-1.02 XM-3.02 XM-3.03F05011-6 Washer, Split Lock, 3/4" XM-3.02 XM-3.03 XM-3.04 XM-4.04 XM-5.01 XM-5.03F05011-61 Washer, Flat, 3/8" SAE XM-5.06F05011-62 Washer, Flat, 3/4" SAE XM-1.02 XM-3.02 XM-3.04 XM-4.04 XM-4.06 XM-5.03F05011-62 Washer, Flat, 3/4" SAE XM-4.02F05011-68 Washer, Flat, 1/2" XM-5.06F05011-73 Washer, Flat, 7/8" SAE XM-3.01 XM-3.01AF05011-74 Washer, Flat, 1/4", Teflon XM-4.11F05011-75 Washer, 1 1/4" ID x 1 3/4" ID x 1/8" XM-4.01 XM-4.02F05011-81 Washer, Star, 9/16" XM-5.06F05011-9 Washer, Split Lock, 1/2" XM-2.01F05012-21 Cotter Pin, 3/16" x 1" XM-4.01 XM-4.03 XM-4.05 XM-5.03F05012-23 Cotter Pin, 3/16" x 1 1/2" XM-4.01 XM-4.02 XM-4.03 XM-4.05 XM-5.01F05012-62 Hitch Pin, #210 XM-2.03F05012-63 Hitch Pin, #216 XM-3.04 XM-4.10 XM-5.01F05013-12 Bolt, 3/4-10 x 1 3/4" XM-3.04F05013-3 Bolt, 3/4-10 x 4" XM-4.02F05013-70 Bolt, 3/4-10 x 6 1/2” XM-4.06



10-7



F05013-71 Bolt, 3/4-10 x 2" XM-3.04 XM-5.03F05015-30 Screw, 5/16” x 3/4”, Self-Tapping XM-5.04

K425 Cable Kit, 521X, 34” XM-3.12M101 Turnbuckle Guard, Fixed, Right XM-4.01 XM-4.03 XM-4.05M102 Turnbuckle Guard, Fixed, Left XM-4.01 XM-4.03 XM-4.05M103 Turnbuckle Guard, Sliding, Right XM-4.05M104 Turnbuckle Guard, Sliding, Left XM-4.05M105 Wheel Height Gauge Scale Plate XM-4.11M106 Wheel Height Gauge Indicator Plate XM-4.11M107 Cover, Main Deck, Slotted XM-3.08M112 Cover, Main Deck, 521X XM-3.08M113 Cover, Main Deck, N/C XM-3.07 XM-3.08M130 Cover End Plate, Deck X3, 521X XM-3.08M132 Cover End Plate, Deck X1, 521X XM-3.08M140 Fender XM-3.09 XM-3.09 XM-3.09 XM-3.09P103 Bearing, Spindle, Top, 6305 RS XM-3.01 XM-3.01AP104 Bearing, Spindle, Bottom, 6206 TGS XM-3.01 XM-3.01AP105 O-Ring, 2 1/2" ID x 2 3/4" OD XM-3.01 XM-3.01AP107 Grease Zerk, 1/4-28 Straight XM-1.01 XM-3.04 XM-3.13 XM-4.01 XM-4.02 XM-4.04P108 Grease Zerk, 1/8" NPT, Straight XM-3.01 XM-3.01A XM-3.13P109 Bushing, Bronze, 1" ID XM-1.01 XM-1.02 XM-2.01 XM-2.03 XM-3.04P109 Bushing, Bronze, 1" ID XM-4.03 XM-4.06 XM-4.07 XM-4.08 XM-5.01P110 Clevis Pin, 3/8” x 1 5/16” XM-4.06P111 Ring, Kick-Out, 1” ID XM-4.06 XM-4.07 XM-4.08P113 Lynch Pin, 1/4" XM-1.01 XM-1.02 XM-5.01 XM-5.03P114 Lynch Pin, 3/16" XM-1.01 XM-5.03P116 Washer, Wear, Zc XM-1.02 XM-3.03 XM-5.01 XM-5.03P117 Decal, Warning, "Hands & Feet" XM-3.07 XM-3.14P121 Hydraulic Cylinder, PP, 3/8" NPT XM-5.01 XM-5.02 XM-5.03P122 Clevis Pin, 3/4” DIA x 4 1/2” XM-4.10P123 Grease Zerk, 1/4-28, 90° XM-3.02 XM-3.03 XM-3.13P125 Decal, Warning, "540 Max" XM-3.07 XM-3.14P126 Decal, Warning, "Replace Guard" XM-3.07 XM-3.14P128 Blade, 21", High-Lift XM-3.01 XM-3.01AP179 Decal, Warning, "Operator's Seat" XM-3.07 XM-3.14P183 Clevis Pin, 1" DIA x 4 1/2" XM-1.01 XM-2.03P187 Tire/Rim Assy, Pneumatic, 16.5 x 6.5 XM-4.03 XM-4.05P188 Hub Assy, 1" ID TRB, Demountable XM-4.03 XM-4.05P190 Tapered Roller Bearing, 1" ID XM-4.01 XM-4.03 XM-4.05P191 Bearing Seal, 1 1/4" ID XM-4.01 XM-4.03 XM-4.05P192 Nut, Castle, 1"-14 XM-4.03 XM-4.05P193 Cotter Pin, 5/32" x 1 3/4" XM-4.03 XM-4.05P194 Nut, Lug, 1/2-20 x 13/16" Tapered XM-4.03 XM-4.05P195 Hub Cap XM-4.01 XM-4.03 XM-4.05P198 Hyd Fitting, 1/4" JIC-1/4" NPT, 90° XM-5.01 XM-5.02P199 Hyd Fitting, 1/4” JIC – 1/4” NPT, ST XM-5.01P203 Bushing, Bronze, 1 1/4" ID XM-4.01 XM-4.05 XM-4.07P212 Clevis Pin, 3/8” x 2 1/8” XM-4.07 XM-4.08P223 Hyd Fittng Adapt, 1/4” NPT–3/8” NPT XM-5.01 XM-5.02P225 PTO, Bondioli, 29.9/45.1, Splined XM-1.03P244 Lift Pin Assembly XM-1.01P246 Blade, 21", Low-Lift XM-3.01 XM-3.01AP256 PTO Shield Retaining Chain, Bondioli XM-1.03P258 PTO 1/2 Shaft, Female, Bondioli XM-1.03P259 PTO 1/2 Shaft, Male, Bondioli XM-1.03P260 PTO Yoke Assy, Twist Rel, F, Bond XM-1.03P261 PTO Yoke Assy, Twist Rel, M, Bond XM-1.03P262 PTO Cross Bearing Assy, Bondioli XM-1.03P263 PTO Female Shaft Yoke, Bondioli XM-1.03P264 PTO Male Shaft Yoke, Bondioli XM-1.03P265 PTO Female Shaft Yoke Pin, Bondioli XM-1.03P266 PTO Male Shaft Yoke Pin, Bondioli XM-1.03P267 PTO Greasing Collar, Bondioli XM-1.03P268 PTO Outer Shield Assembly, Bondioli XM-1.03P269 PTO Inner Shield Assembly, Bondioli XM-1.03



10-8



P270 PTO Outer Shield Bearing, Bondioli XM-1.03P271 PTO Inner Shield Bearing, Bondioli XM-1.03P272 PTO Twist Sleeve Assembly, Bondioli XM-1.03P273 PTO Cross Pin Assembly, Bondioli XM-1.03P274 PTO Shaft, Female, Bondioli XM-1.03P275 PTO Shaft, Male, Bondioli XM-1.03P276 PTO Yoke Shield, F Side, Bondioli XM-1.03P277 PTO Outer Shaft Shield, Bondioli XM-1.03P278 PTO Yoke Shield, M Side, Bondioli XM-1.03P279 PTO Inner Shaft Shield, Bondioli XM-1.03P289 Bearing Race Insert, 1" ID TRB XM-4.01 XM-4.03 XM-4.05P291 Wheel Hub/Brng Assy, 3/4" TRB, DM XM-4.09P292 Bearing, Tapered Roller, 3/4" ID XM-4.09P293 Seal, TRB, 1 1/8" ID XM-4.09P294 Grease Zerk, 1/4-28, 45° XM-1.03 XM-2.03 XM-3.13 XM-4.03 XM-4.05 XM-4.05 XM-4.09P296 Bearing Spacer, 3/4” ID x 1/2”, SS XM-4.06 XM-4.08P297 Wheel Hub Assembly, DM XM-4.09P300 Gearbox, SGCM500SAR21, StBv, Sp XM-2.01P303 Gearbox Seal, 1 3/8" XM-2.02P322 Blade, 21", Gator Mulching XM-3.01 XM-3.01AP325 Gearbox Gear, 30 Teeth XM-2.02P326 Gearbox Casting, Top XM-2.02P327 Bolt, 3/8-16 x 2 1/4", SHCS XM-2.02P328 Key, 5/16" SQ x 1.2" XM-2.02P329 Gearbox Retaining Ring XM-2.02P330 Gearbox Pipe Plug, 1/2" NPT XM-2.02P331 Gearbox Breather Plug XM-2.02P332 Gearbox Pinion Shaft XM-2.02P333 Gearbox Cross Shaft XM-2.02P334 Gearbox Casting, Bottm (W/Breather) XM-2.02P402 Bearing Race Insert, 3/4" ID, TRB XM-4.09P403 Bushing, Bronze, 3/4" ID XM-1.01P406 Key, 1/2" x 1/4" x 3/4" XM-2.01P407 Key, 3/16" SQ x 5/8" XM-3.01 XM-3.01AP408 Pulley, Idler XM-2.03P410 Spring, Extension, 1" x 7" XM-2.03P411 Clevis Pin, 1" DIA x 3 1/8" XM-5.01P413 Cable, Lift, X2 XM-5.05 XM-5.06P414 Cable, Lift, X1/X3 XM-5.05 XM-5.06P416 Spring, Compression, 2" x 6" XM-1.01P417 Delrin Wear Pad, 1" ID x 8" DIA XM-2.01P418 Pulley, Drive, 2B5V154 XM-2.01P419 Bushing Assy, Split Taper, 1 3/8" x B XM-2.01P420 Delrin Wear Pad, Belt Cover XM-3.08P421 Cover, Belt, Deck X7 XM-3.07 XM-3.08P422 Cover, Belt, Deck X6 XM-3.07 XM-3.08P423 Cover, Belt, Deck X1 XM-3.07 XM-3.08P424 Cover, Belt, Deck X3 XM-3.07 XM-3.08P425 Cover, Belt, Deck X4 XM-3.07 XM-3.08

P425A Cover, Belt, Deck X5 XM-3.07 XM-3.08P427 Belt, B-60 XM-3.01 XM-3.01AP430 Spring, Torsion, 180°, LH XM-3.08P433 Bearing Washer, 3/4" ID XM-4.01P434 Nut, Castle, 3/4-16 XM-4.01P435 Bushing, Bronze, 1 1/4" ID x 1" XM-4.01P436 Bushing, Bronze, 1/2" ID XM-3.08P437 Key, 5/16" SQ x 1 3/4" XM-2.01P438 Anti-Scalp Wheel, 6” x 3.5” x 3/4” ID XM-4.10P440 Clamp, Hydraulic Hose, 1/2” XM-5.04 XM-5.06P442 Decal, Warning, "Outer Decks" XM-3.07 XM-3.14P443 Gas Spring Cylinder XM-5.01P444 Ball Stud, 10 MM x 5/16-18 x 1/2" XM-5.01P445 Hyd Fitting, 1/4" JIC-3/8" NPT, 90° XM-5.02P447 Cotter Pin, 1/8" x 1 1/2" XM-4.01P448 Ball Stud Retaining Clip XM-5.01



10-9



P449 Chain Snap Link, 1/4” XM-3.11 XM-3.12P450 Belt, B-58 Insta-Power XM-2.01P459 Spring, Torsion, 180°, RH XM-3.08P463 Clevis Pin, 1" DIA x 3 1/2" XM-5.03P464 Spring, Extension, 1 3/16" x 7 1/2" XM-5.02 XM-5.03P468 Cable Clamp, 3/16” XM-3.12P737 Bushing, Bronze, 1" ID x 3/4" XM-2.01P786 Bushing, Steel, 3/4" ID XM-1.01P787 Bushing, Steel, 1" ID XM-1.01 XM-1.02P843 Washer, Wave, 1” ID XM-4.06 XM-4.08P844 Washer, Wave, 1 1/4” ID XM-4.07T104 Spacer, 1" ID x 1 3/4" OD x 1/4" XM-3.03 XM-4.06 XM-5.01 XM-4.08T107 Spacer, 1" ID x 1" XM-3.02 XM-4.06 XM-4.08T125 Bearing Spacer, 3/4” ID x 3/8” XM-4.07T126 Bearing Spacer, 3/4” x 11/16” XM-4.07 XM-4.08T132 Spacer, 1 1/4” x 1/4” XM-1.01 XM-4.01 XM-4.07T133 Spacer, 1 1/4” ID x 1” XM-4.07T153 Turnbuckle, 3/4-16 XM-4.01 XM-4.03 XM-4.05T154 Turnbuckle Shoulder Bolt XM-4.01 XM-4.03 XM-4.05T156 Pulley, Double, XS XM-3.01 XM-3.01AT157 Spindle, Keyed XM-3.01 XM-3.01AT159 Pull Pin, SQHD, XS XM-1.02T160 Pulley, Quad, XS XM-3.01 XM-3.01AT161 Cable Lift End XM-5.06T167 Washer, Limit, Round XM-3.03T180 Spindle Spacer, 1" XM-3.01W118 Wheel Yoke Weldment, 9” Swivel RT XM-4.06W340 Deck Weldment, X1, 3" XM-3.06W341 Deck Weldment, X2, 3" XM-3.06W342 Deck Weldment, X3, 3" XM-3.06W343 Deck Weldment, X4/X5, 3" XM-3.06 XM-3.06W345 Deck Weldment, X6, 3" XM-3.06W346 Deck Weldment, X7, 3" XM-3.06W352 Wheel Arm Weldment, 13", Left XM-4.01W353 Turnbuckle End Wldmt, 1” Fixed, RH XM-4.01 XM-4.03 XM-4.05W354 Turnbuckle End Weldment, 1/2”, RH XM-4.01 XM-4.03 XM-4.05W355 Wheel Arm Wldment, 16.5", Fixed, LF XM-4.03 XM-4.05W357 Turnbuckle End Wldmnt, Sliding, RH XM-4.05W358 Pivot Slide Bar Weldment, 4 1/2" XM-3.02W365 Wheel Arm Wldmnt, 16.5", Fixed, RT XM-4.03 XM-4.05W366 Idler Arm Weldment XM-2.03W370 Wheel Arm Weldment, 13", Right XM-4.01W371 Wheel Arm Weldment, Sliding, Right XM-4.05W375 Chain Weldment, Deck Hanger XM-3.05W378 Deck Pivot Arm Weldment, X6 (Left) XM-3.04W383 Deck Pivot Arm Weldment, X7 (Right) XM-3.04W384 Grass Chute Weldment, Guarded XM-3.10W385 Cylinder Pull Arm Weldment XM-5.01W387 Lift Arm End Weldment, Right XM-5.01W388 Lift Arm End Weldment, Left XM-5.01W389 Cylinder Base Weldment XM-5.01W390 Cylinder Pivot Block Weldment, Right XM-5.01W392 Cylinder Pivot Block Weldment, Left XM-5.01W393 Lift Arm Weldment XM-5.01W394 Pull Arm Weldment, Left XM-1.01W395 Pull Arm Weldment, Right XM-1.01W397 Weight Transfer Rod Weldment, Fxd XM-1.01W398 Pull Bar Weldment, XS XM-1.02W399 Gearbox Channel Weldment, XS XM-2.01W400 Cover Weldment, Drive Pulley XM-2.01W401 Cover Mount Weldment, Belt, X6 XM-3.08W402 Cover Mount Weldment, Belt, X7 XM-3.08W403 Cover Weldment, Belt, Hinged, X1 XM-3.07 XM-3.08W404 Cover Weldment, Belt, Hinged, X3 XM-3.07 XM-3.08W412 Wheel Arm Weldment, Sliding, Left XM-4.05



10-10



W414 Stud Weldment, 3/8-16 x 6 ½” XM-3.08W415 Axle Weldment, Flagged XM-4.05W416 Deck Pivot Arm Rod Weldment XM-3.04W417 Fender Weldment, Rear, Left XM-3.09W418 Fender Weldment, Rear, Right XM-3.09W419 Turnbuckle End Wldment, 1” Fxd, LH XM-4.01 XM-4.03 XM-4.05W420 Turnbuckle End Weldment, 1/2”, LH XM-4.01 XM-4.03 XM-4.05W421 Turnbuckle End Wldment, Sliding, LH XM-4.05W422 Cable Support Loop Weldment XM-5.06W423 Pivot Slide Bar Weldment, 5" XM-3.03W424 Hydraulic Hose Support Loop Wldmnt XM-2.01 XM-5.04W425 Fender Weldment, Rear, Center XM-3.09W431 Lift Arm Slide Tube Weldment XM-5.02 XM-5.03W432 Lift Arm Weldment, 3/4-10 Thread XM-5.02 XM-5.03W433 Cylinder Pivot Arm Weldment, RT XM-5.02 XM-5.03W434 Cylinder Pivot Arm Weldment, LF XM-5.02 XM-5.03W435 Cylinder Base Plate Weldment XM-5.02 XM-5.03W440 Deck Weldment, X1, 4" XM-3.06W441 Deck Weldment, X2, 4" XM-3.06W442 Deck Weldment, X3, 4" XM-3.06W443 Deck Weldment, X4, 4" XM-3.06W444 Deck Weldment, X5, 4" XM-3.06W445 Deck Weldment, X6, 4" XM-3.06W446 Deck Weldment, X7, 4" XM-3.06W460 Swivel Wheel Leg Weldment, X1 XM-4.02W461 Swivel Wheel Leg Weldment, X3 XM-4.02W468 Discharge Extension Wldment, 521X XM-3.10W470 Deck Lift Arm Weldment, Rear, RT XM-5.02 XM-5.03W471 Deck Lift Arm Weldment, Rear, LF XM-5.02 XM-5.03W472 Spring Plate Weldment, Right XM-5.02 XM-5.03W473 Spring Plate Weldment, Left XM-5.02 XM-5.03W476 Dual Wheel Yoke Weldment, RT XM-4.07W477 Dual Whl Yoke Leg Mnt Wldmnt, RT XM-4.04W478 Dual Wheel Yoke Leg Weldment, RT XM-4.04W479 Dual Whl Yoke Leg Mnt Wldmnt, LF XM-4.04W480 Dual Wheel Yoke Leg Weldment, LF XM-4.04W481 Axle Weldment, Dual Wheel XM-4.07W482 Dual Wheel Yoke Weldment, LF XM-4.07W483 Weight Trans Rod Wldmnt, Fxd, NXS XM-1.01W488 Deck Weldment, X1, NXS XM-3.06W489 Deck Weldment, X3, NXS XM-3.06W490 Deck Weldment, X7, NXS XM-3.06W491 Pull Bar Weldment, NXS XM-1.02W492 Deck Weldment, X6, NXS XM-3.06W500 Deck Weldment, X4, NXS XM-3.06W501 Deck Weldment, X5, NXS XM-3.06W531 Deck Weldment, X2, NXS+ XM-3.06W685 Wheel Yoke Weldment, Fixed, LF XM-4.08W686 Wheel Yoke Weldment, Fixed, RT XM-4.08W688 Wheel Yoke Weldment, 9” Swivel LF XM-4.06



10-11

Parts IndexListed By Part Description


C575 Anti-Scalp Roller Tube XM-4.10 XM-4.10 XM-4.10 XM-4.10 XM-4.10 XM-4.10 XM-4.10P438 Anti-Scalp Wheel, 6” x 3.5” x 3/4” ID XM-4.10C489 Axle, Drilled XM-4.03 XM-4.05W415 Axle Weldment, Flagged XM-4.05W481 Axle Weldment, Dual Wheel XM-4.07P448 Ball Stud Retaining Clip XM-5.01P444 Ball Stud, 10 MM DIA x 5/16-18 x 1/2" XM-5.01P289 Bearing Race Insert, 1" ID TRB XM-4.01 XM-4.03 XM-4.05P402 Bearing Race Insert, 3/4" ID, TRB XM-4.09P191 Bearing Seal, 1 1/4" ID XM-4.01 XM-4.03 XM-4.05P296 Bearing Spacer, 3/4” ID x 1/2”, SS XM-4.06 XM-4.08T125 Bearing Spacer, 3/4” ID x 3/8” XM-4.07T126 Bearing Spacer, 3/4” x 11/16” XM-4.07 XM-4.08P433 Bearing Washer, 3/4" ID XM-4.01P104 Bearing, Spindle, Bottom, 6206 TGS XM-3.01 XM-3.01AP103 Bearing, Spindle, Top, 6305 RS XM-3.01 XM-3.01AP292 Bearing, Tapered Roller, 3/4" ID XM-4.09P450 Belt, B-58 Insta-Power XM-2.01P427 Belt, B-60 XM-3.01 XM-3.01AP322 Blade, 21", Gator Mulching XM-3.01 XM-3.01AP128 Blade, 21", High-Lift XM-3.01 XM-3.01AP246 Blade, 21", Low-Lift XM-3.01 XM-3.01A

F05008-37 Bolt, 1/2-13 x 1 1/4" XM-2.01F05009-66 Bolt, 1/2-13 x 2 3/4", G8 XM-2.03

F05008-106 Bolt, 1/2-13 x 4 3/4” XM-4.10F05005-101 Bolt, 1/4-20 x 1" XM-4.09F05009-67 Bolt, 1/4-20 x 3/4 ", G8 XM-2.01F05009-69 Bolt, 1-8 x 3", G8 XM-1.02 XM-3.02 XM-4.04

F05004-155 Bolt, 1-8 x 4 1/2", G8 XM-3.03F05004-154 Bolt, 1-8 x 4", G8 XM-3.02F05004-132 Bolt, 1-8 x 5", G8 XM-3.03F05013-12 Bolt, 3/4-10 x 1 3/4" XM-3.04F05009-44 Bolt, 3/4-10 x 2 1/2” XM-4.04F05013-71 Bolt, 3/4-10 x 2" XM-3.04 XM-5.03F05009-54 Bolt, 3/4-10 x 3 1/2" XM-3.04F05009-36 Bolt, 3/4-10 x 3" XM-1.02 XM-3.04 XM-4.04F05013-3 Bolt, 3/4-10 x 4" XM-4.02F05013-70 Bolt, 3/4-10 x 6 1/2” XM-4.06

P327 Bolt, 3/8-16 x 2 1/4", SHCS XM-2.02F05007-135 Bolt, 3/8-16 x 3 1/4" XM-5.06F05007-27 Bolt, 3/8-16 x 3/4” XM-1.01F05009-62 Bolt, 5/16-18 x 1 1/4" XM-5.06F05009-70 Bolt, 5/16-18 x 1 3/4" XM-5.06F05006-1 Bolt, 5/16-18 x 1" XM-2.01 XM-3.08 XM-3.09 XM-3.10 XM-3.10F05009-79 Bolt, 5/16-18 x 2", G8 XM-5.06F05006-5 Bolt, 5/16-18 x 3/4” XM-3.08 XM-3.09 XM-3.09F05008-95 Bolt, 5/8-18 x 1 1/4" XM-3.01 XM-3.01AF05009-80 Bolt, 5/8-18 x 2 1/4" XM-3.01 XM-3.01AF05009-60 Bolt, 7/16-14 x 1 3/4", G8 XM-3.05

F05005-122 Bolt, AH, 1/4-20 x 1 1/2", SS XM-4.01 XM-4.03 XM-4.05F05005-121 Bolt, AH, 1/4-20 x 1 1/4", SS XM-4.01 XM-4.03 XM-4.05F05005-119 Bolt, AH, 1/4-20 x 1 3/4", SS XM-4.01 XM-4.03 XM-4.05F05005-120 Bolt, AH, 1/4-20 x 1", SS XM-4.01 XM-4.03 XM-4.05 XM-4.05F05009-71 Bolt, AH, 1/4-20 x 5/8", SS XM-4.01 XM-4.03 XM-4.05F05006-83 Bolt, Eye, 5/16-18 x 1 1/4” XM-3.12

P419 Bushing Assy, Split Taper, 1 3/8" x B XM-2.01P203 Bushing, Bronze, 1 1/4" ID XM-4.01 XM-4.05 XM-4.07P435 Bushing, Bronze, 1 1/4" ID x 1" XM-4.01P109 Bushing, Bronze, 1" ID XM-1.01 XM-1.02 XM-2.01 XM-2.03 XM-3.04P109 Bushing, Bronze, 1" ID XM-4.03 XM-4.06 XM-4.07 XM-4.08 XM-5.01P737 Bushing, Bronze, 1" ID x 3/4" XM-2.01P436 Bushing, Bronze, 1/2" ID XM-3.08P403 Bushing, Bronze, 3/4" ID XM-1.01P787 Bushing, Steel, 1" ID XM-1.01 XM-1.02



10-12



P786 Bushing, Steel, 3/4" ID XM-1.01A324 Cable Assembly, 521X, 34” XM-3.12A235 Cable Assembly, X1/X3 XM-5.06A236 Cable Assembly, X2 XM-5.06P468 Cable Clamp, 3/16” XM-3.12K425 Cable Kit, 521X, 34” XM-3.12T161 Cable Lift End XM-5.06C549 Cable Mount Plate XM-3.12C377 Cable Retainer Spacer Tube XM-5.06W422 Cable Support Loop Weldment XM-5.06C550 Cable, 521X, 34” XM-3.12P414 Cable, Lift, X1/X3 XM-5.05 XM-5.06P413 Cable, Lift, X2 XM-5.05 XM-5.06C546 Chain Mount Plate, Safety XM-3.11P449 Chain Snap Link, 1/4” XM-3.11 XM-3.12W375 Chain Weldment, Deck Hanger XM-3.05C529 Chain, Safety, 100” XM-3.11C547 Chain, Safety, 78” XM-3.11P440 Clamp, Hydraulic Hose, 1/2” XM-5.04 XM-5.06C413 Clamping Plate, Side XM-3.04C506 Clamping Plate, Top XM-3.04P463 Clevis Pin, 1" DIA x 3 1/2" XM-5.03P411 Clevis Pin, 1" DIA x 3 1/8" XM-5.01P183 Clevis Pin, 1" DIA x 4 1/2" XM-1.01 XM-2.03P122 Clevis Pin, 3/4” DIA x 4 1/2” XM-4.10P110 Clevis Pin, 3/8” x 1 5/16” XM-4.06P212 Clevis Pin, 3/8” x 2 1/8” XM-4.07 XM-4.08P447 Cotter Pin, 1/8" x 1 1/2" XM-4.01

F05012-23 Cotter Pin, 3/16" x 1 1/2" XM-4.01 XM-4.02 XM-4.03 XM-4.05 XM-5.01F05012-21 Cotter Pin, 3/16" x 1" XM-4.01 XM-4.03 XM-4.05 XM-5.03

P193 Cotter Pin, 5/32" x 1 3/4" XM-4.03 XM-4.05M132 Cover End Plate, Deck X1, 521X XM-3.08M130 Cover End Plate, Deck X3, 521X XM-3.08W401 Cover Mount Weldment, Belt, X6 XM-3.08W402 Cover Mount Weldment, Belt, X7 XM-3.08W403 Cover Weldment, Belt, Hinged, X1 XM-3.07 XM-3.08W404 Cover Weldment, Belt, Hinged, X3 XM-3.07 XM-3.08W400 Cover Weldment, Drive Pulley XM-2.01P423 Cover, Belt, Deck X1 XM-3.07 XM-3.08P424 Cover, Belt, Deck X3 XM-3.07 XM-3.08P425 Cover, Belt, Deck X4 XM-3.07 XM-3.08

P425A Cover, Belt, Deck X5 XM-3.07 XM-3.08P422 Cover, Belt, Deck X6 XM-3.07 XM-3.08P421 Cover, Belt, Deck X7 XM-3.07 XM-3.08M112 Cover, Main Deck, 521X XM-3.08M113 Cover, Main Deck, N/C XM-3.07 XM-3.08M107 Cover, Main Deck, Slotted XM-3.08C510 Cover, Pivot Arm, Deck X1/X3 XM-3.08W435 Cylinder Base Plate Weldment XM-5.02 XM-5.03W389 Cylinder Base Weldment XM-5.01W434 Cylinder Pivot Arm Weldment, LF XM-5.02 XM-5.03W433 Cylinder Pivot Arm Weldment, RT XM-5.02 XM-5.03W392 Cylinder Pivot Block Weldment, Left XM-5.01W390 Cylinder Pivot Block Weldment, Right XM-5.01W385 Cylinder Pull Arm Weldment XM-5.01C444 Cylinder Tie Rod XM-5.01C527 Cylinder Tie Rod, 3/4" XM-5.02 XM-5.03

018009 Decal, Die-Cut, "Articulator" XM-3.07 XM-3.14018008 Decal, Die-Cut, "LasTec" XM-3.07 XM-3.14P125 Decal, Warning, "540 Max" XM-3.07 XM-3.14P117 Decal, Warning, "Hands & Feet" XM-3.07 XM-3.14P179 Decal, Warning, "Operator's Seat" XM-3.07 XM-3.14P442 Decal, Warning, "Outer Decks" XM-3.07 XM-3.14P126 Decal, Warning, "Replace Guard" XM-3.07 XM-3.14W471 Deck Lift Arm Weldment, Rear, LF XM-5.02 XM-5.03



10-13



W470 Deck Lift Arm Weldment, Rear, RT XM-5.02 XM-5.03W416 Deck Pivot Arm Rod Weldment XM-3.04W378 Deck Pivot Arm Weldment, X6 (Left) XM-3.04W383 Deck Pivot Arm Weldment, X7 (Right) XM-3.04W340 Deck Weldment, X1, 3" XM-3.06W440 Deck Weldment, X1, 4" XM-3.06

040231 Deck Weldment, X1, DBS XM-3.06W488 Deck Weldment, X1, NXS XM-3.06W341 Deck Weldment, X2, 3" XM-3.06W441 Deck Weldment, X2, 4" XM-3.06

040232 Deck Weldment, X2, DBS XM-3.06W531 Deck Weldment, X2, NXS+ XM-3.06W342 Deck Weldment, X3, 3" XM-3.06W442 Deck Weldment, X3, 4" XM-3.06

040233 Deck Weldment, X3, DBS XM-3.06W489 Deck Weldment, X3, NXS XM-3.06W443 Deck Weldment, X4, 4" XM-3.06W343 Deck Weldment, X4/X5, 3" XM-3.06 XM-3.06W500 Deck Weldment, X4, NXS XM-3.06

040234 Deck Weldment, X4, DBS XM-3.06W444 Deck Weldment, X5, 4" XM-3.06W501 Deck Weldment, X5, NXS XM-3.06

040235 Deck Weldment, X5, DBS XM-3.06W345 Deck Weldment, X6, 3" XM-3.06W445 Deck Weldment, X6, 4" XM-3.06W492 Deck Weldment, X6, NXS XM-3.06

040236 Deck Weldment, X6, DBS XM-3.06W346 Deck Weldment, X7, 3" XM-3.06W446 Deck Weldment, X7, 4" XM-3.06W490 Deck Weldment, X7, NXS XM-3.06

040237 Deck Weldment, X7, DBS XM-3.06P417 Delrin Wear Pad, 1" ID x 8" DIA XM-2.01P420 Delrin Wear Pad, Belt Cover XM-3.08W468 Discharge Extension Weldment, 521X XM-3.10W479 Dual Whl Yoke Leg Mnt Wldmnt, LF XM-4.04W477 Dual Whl Yoke Leg Mnt Wldmnt, RT XM-4.04W480 Dual Wheel Yoke Leg Weldment, LF XM-4.04W478 Dual Wheel Yoke Leg Weldment, RT XM-4.04W482 Dual Wheel Yoke Weldment, LF XM-4.07W476 Dual Wheel Yoke Weldment, RT XM-4.07

F05009-76 Eye Bolt, 1/2-13 x 2" XM-5.06M140 Fender XM-3.09 XM-3.09 XM-3.09 XM-3.09W425 Fender Weldment, Rear, Center XM-3.09W417 Fender Weldment, Rear, Left XM-3.09W418 Fender Weldment, Rear, Right XM-3.09P443 Gas Spring Cylinder XM-5.01A241 Gas Spring Cylinder Assembly XM-5.01

019663 Gearbox Bearing XM-2.02019662 Gearbox Bearing Cup XM-2.02P331 Gearbox Breather Plug XM-2.02P334 Gearbox Casting, Bottm (W/Breather) XM-2.02P326 Gearbox Casting, Top XM-2.02W399 Gearbox Channel Weldment, XS XM-2.01P333 Gearbox Cross Shaft XM-2.02P325 Gearbox Gear, 30 Teeth XM-2.02P332 Gearbox Pinion Shaft XM-2.02P330 Gearbox Pipe Plug, 1/2" NPT XM-2.02P329 Gearbox Retaining Ring XM-2.02P303 Gearbox Seal, 1 3/8" XM-2.02P300 Gearbox, SGCM500SAR21, StBv, Sp XM-2.01W384 Grass Chute Weldment, Guarded XM-3.10P107 Grease Zerk, 1/4-28 Straight XM-1.01 XM-3.04 XM-3.13 XM-4.01 XM-4.02 XM-4.04P294 Grease Zerk, 1/4-28, 45° XM-1.03 XM-2.03 XM-3.13 XM-4.03 XM-4.05 XM-4.05 XM-4.09P123 Grease Zerk, 1/4-28, 90° XM-3.02 XM-3.03 XM-3.13P108 Grease Zerk, 1/8" NPT, Straight XM-3.01 XM-3.01A XM-3.13



10-14



F05012-62 Hitch Pin, #210 XM-2.03F05012-63 Hitch Pin, #216 XM-3.04 XM-4.10 XM-5.01

P188 Hub Assy, 1" ID TRB, Demountable XM-4.03 XM-4.05P195 Hub Cap XM-4.01 XM-4.03 XM-4.05P121 Hydraulic Cylinder, PP, 3/8" NPT XM-5.01 XM-5.02 XM-5.03P223 Hyd Fitting Adapt, 1/4” NPT–3/8” NPT XM-5.01 XM-5.02P198 Hyd Fitting, 1/4" JIC-1/4" NPT, 90° XM-5.01 XM-5.02P445 Hyd Fitting, 1/4" JIC-3/8" NPT, 90° XM-5.02P199 Hyd Fitting, 1/4” JIC – 1/4” NPT, St XM-5.01W424 Hydraulic Hose Support Loop Wldmnt XM-2.01 XM-5.04W366 Idler Arm Weldment XM-2.03P406 Key, 1/2" x 1/4" x 3/4" XM-2.01P407 Key, 3/16" SQ x 5/8" XM-3.01 XM-3.01AP437 Key, 5/16" SQ x 1 3/4" XM-2.01P328 Key, 5/16" SQ x 1.2" XM-2.02

040250 Kit, Nylon Blade Washer XM-3.01 XM-3.01A040249 Kit, Slide Bar Hardware Upfit XM-3.02W388 Lift Arm End Weldment, Left XM-5.01W387 Lift Arm End Weldment, Right XM-5.01W431 Lift Arm Slide Tube Weldment XM-5.02 XM-5.03W393 Lift Arm Weldment XM-5.01W432 Lift Arm Weldment, 3/4-10 Thread XM-5.02 XM-5.03P244 Lift Pin Assembly XM-1.01P113 Lynch Pin, 1/4" XM-1.01 XM-1.02 XM-5.01 XM-5.03P114 Lynch Pin, 3/16" XM-1.01 XM-5.03

F05010-161 Nut, 2-Way Locking Jam, 3/4-10 XM-3.02P192 Nut, Castle, 1"-14 XM-4.03 XM-4.05P434 Nut, Castle, 3/4-16 XM-4.01

F05010-127 Nut, Half Nylock, 1/2-13 XM-4.10F05010-122 Nut, Half Nylock, 3/4-10 XM-3.02 XM-4.08F05010-35 Nut, Hex, 1/2-13 XM-5.06F05010-63 Nut, Hex, 1/4-20 XM-4.09F05010-7 Nut, Hex, 3/4-10 XM-3.02 XM-3.03 XM-3.04 XM-4.04 XM-5.01F05010-17 Nut, Hex, 5/16-18 XM-3.12

F05010-139 Nut, Hex, 7/8-14 XM-3.01 XM-3.01AF05010-147 Nut, Hex, 9/16-12 XM-5.06F05010-104 Nut, Jam, 3/4-10 XM-3.02 XM-3.03 XM-3.04F05010-9 Nut, Keps, 1/4-20 XM-4.01 XM-4.03 XM-4.05

P194 Nut, Lug, 1/2-20 x 13/16" Tapered XM-4.03 XM-4.05F05010-142 Nut, Lug, 5/16-24 Tapered XM-4.09F05010-8 Nut, Nylock, 1/2-13 XM-2.03 XM-3.05 XM-4.01 XM-4.03 XM-4.05 XM-5.06F05010-69 Nut, Nylock, 1/4-20 XM-3.08

F05010-109 Nut, Nylock, 1-8 XM-2.01 XM-3.03 XM-4.04 XM-5.03F05010-103 Nut, Nylock, 3/4-10 XM-1.02 XM-3.04 XM-4.06 XM-4.07F05010-10 Nut, Nylock, 3/8-16 XM-3.08 XM-3.08 XM-5.06F05010-58 Nut, Nylock, 5/16-18 XM-3.08 XM-3.10 XM-3.10 XM-3.12 XM-5.06 XM-5.06

F05010-149 Nut, Nylock, 5/16-24 XM-5.06F05010-135 Nut, Nylock, 7/16-14 XM-3.05F05010-103 Nut, Nylock,3/4-10 XM-4.02F05010-24 Nut, Wing, 3/8-16 XM-3.08

P105 O-Ring, 2 1/2" ID x 2 3/4" OD XM-3.01 XM-3.01A029096 Pivot Pin Weldment XM-1.01W358 Pivot Slide Bar Weldment, 4 1/2" XM-3.02W423 Pivot Slide Bar Weldment, 5" XM-3.03P258 PTO 1/2 Shaft, Female, Bondioli XM-1.03P259 PTO 1/2 Shaft, Male, Bondioli XM-1.03P262 PTO Cross Bearing Assembly, Bond XM-1.03P273 PTO Cross Pin Assembly, Bondioli XM-1.03P265 PTO Female Shaft Yoke Pin, Bondioli XM-1.03P263 PTO Female Shaft Yoke, Bondioli XM-1.03P267 PTO Greasing Collar, Bondioli XM-1.03P279 PTO Inner Shaft Shield, Bondioli XM-1.03P269 PTO Inner Shield Assembly, Bondioli XM-1.03P271 PTO Inner Shield Bearing, Bondioli XM-1.03P266 PTO Male Shaft Yoke Pin, Bondioli XM-1.03



10-15



P264 PTO Male Shaft Yoke, Bondioli XM-1.03P277 PTO Outer Shaft Shield, Bondioli XM-1.03P268 PTO Outer Shield Assembly, Bondioli XM-1.03P270 PTO Outer Shield Bearing, Bondioli XM-1.03P274 PTO Shaft, Female, Bondioli XM-1.03P275 PTO Shaft, Male, Bondioli XM-1.03P256 PTO Shield Retaining Chain, Bondioli XM-1.03P272 PTO Twist Sleeve Assembly, Bondioli XM-1.03P260 PTO Yoke Assy, Twist Rel, F, Bond XM-1.03P261 PTO Yoke Assy, Twist Rel, M, Bond XM-1.03P276 PTO Yoke Shield, Female Side, Bond XM-1.03P278 PTO Yoke Shield, Male Side, Bondioli XM-1.03P225 PTO, Bondioli, 29.9/45.1, Splined XM-1.03W394 Pull Arm Weldment, Left XM-1.01W395 Pull Arm Weldment, Right XM-1.01C544 Pull Bar L-Pin XM-1.02W491 Pull Bar Weldment, NXS XM-1.02W398 Pull Bar Weldment, XS XM-1.02T159 Pull Pin, SQHD, XS XM-1.02T156 Pulley, Double, XS XM-3.01 XM-3.01AP418 Pulley, Drive, 2B5V154 XM-2.01P408 Pulley, Idler XM-2.03T160 Pulley, Quad, XS XM-3.01 XM-3.01AC576 Retro Anti-Scalp Roller Tube XM-4.10P111 Ring, Kick-Out, 1” ID XM-4.06 XM-4.07 XM-4.08

F04203-11 Rivet, 3/16" x 1/4" XM-3.08F05015-30 Screw, 5/16” x 3/4”, Self-Tapping XM-5.04

F05005-118 Screw, SFH, 1/4-20 x 1" XM-3.08F05009-75 Screw, Wing, 1/4-20 x 1/2" XM-4.11F05009-77 Screw, Wing, 3/8-16 x 5/8" XM-3.08

P293 Seal, TRB, 1 1/8" ID XM-4.09T133 Spacer, 1 1/4” ID x 1” XM-4.07 XM-4.08T132 Spacer, 1 1/4” x 1/4” XM-1.01 XM-4.01 XM-4.07 XM-4.08T104 Spacer, 1" ID x 1 3/4" OD x 1/4" XM-3.03 XM-4.06 XM-5.01T107 Spacer, 1" ID x 1" XM-3.02 XM-4.06T180 Spindle Spacer, 1" XM-3.01

018309 Spindle, Extended XM-3.01 XM-3.01AT157 Spindle, Keyed XM-3.01 XM-3.01AW473 Spring Plate Weldment, Left XM-5.02 XM-5.03W472 Spring Plate Weldment, Right XM-5.02 XM-5.03P416 Spring, Compression, 2" x 6" XM-1.01P464 Spring, Extension, 1 3/16" x 7 1/2" XM-5.02 XM-5.03P410 Spring, Extension, 1" x 7" XM-2.03P430 Spring, Torsion, 180°, LH XM-3.08P459 Spring, Torsion, 180°, RH XM-3.08W414 Stud Weldment, 3/8-16 x 6 ½” XM-3.08

F05004-111 Stud, Press-In, 1/2-20 x 1 13/16" XM-4.03 XM-4.05F05004-112 Stud, Press-In, 5/16-24 x 3/4" XM-4.09

W460 Swivel Wheel Leg Weldment, X1 XM-4.02W461 Swivel Wheel Leg Weldment, X3 XM-4.02P190 Tapered Roller Bearing, 1" ID XM-4.01 XM-4.03 XM-4.05P187 Tire/Rim Assy, Pneumatic, 16.5 x 6.5 XM-4.03 XM-4.05C554 Trim, Rubber, 9 1/2" XM-3.08W420 Turnbuckle End Weldment, 1/2”, LH XM-4.01 XM-4.03 XM-4.05W354 Turnbuckle End Weldment, 1/2”, RH XM-4.01 XM-4.03 XM-4.05W419 Turnbuckle End Wldmnt, 1” Fixed, LH XM-4.01 XM-4.03 XM-4.05W353 Turnbuckle End Wldmnt, 1” Fixed, RH XM-4.01 XM-4.03 XM-4.05W421 Turnbuckle End Wldmnt, Sliding, LH XM-4.05W357 Turnbuckle End Wldmnt, Sliding, RH XM-4.05M102 Turnbuckle Guard, Fixed, Left XM-4.01 XM-4.03 XM-4.05M101 Turnbuckle Guard, Fixed, Right XM-4.01 XM-4.03 XM-4.05M104 Turnbuckle Guard, Sliding, Left XM-4.05M103 Turnbuckle Guard, Sliding, Right XM-4.05T154 Turnbuckle Shoulder Bolt XM-4.01 XM-4.03 XM-4.05T153 Turnbuckle, 3/4-16 XM-4.01 XM-4.03 XM-4.05



10-16



F05011-75 Washer, 1 1/4" ID x 1 3/4" ID x 1/8" XM-4.01 XM-4.02F05011-4 Washer, 3/8” XM-1.01F05011-44 Washer, Fender, 3/8" XM-3.08F05011-50 Washer, Fender, 5/16” XM-3.10

F05011-105 Washer, Fender, 5/16” x 1/8” XM-3.09 XM-3.10F05011-68 Washer, Flat, 1/2" XM-5.06F05011-2 Washer, Flat, 1/2" SAE XM-2.03 XM-4.01 XM-4.03 XM-4.05F05011-11 Washer, Flat, 1/4" SAE XM-3.08 XM-4.05F05011-74 Washer, Flat, 1/4", Teflon XM-4.11F05011-29 Washer, Flat, 3/4" XM-1.02F05011-62 Washer, Flat, 3/4" SAE XM-3.02 XM-4.02F05011-62 Washer, Flat, 3/4" SAE XM-1.02 XM-3.04 XM-4.04 XM-4.06 XM-5.03F05011-61 Washer, Flat, 3/8" SAE XM-5.06F05011-16 Washer, Flat, 5/16" XM-2.01 XM-3.10 XM-3.10 XM-3.12 XM-5.06F05011-17 Washer, Flat, 5/16” SAE XM-3.08 XM-3.08 XM-5.06F05011-40 Washer, Flat, 5/8" XM-3.01AF05011-43 Washer, Flat, 7/16" SAE XM-3.05F05011-73 Washer, Flat, 7/8" SAE XM-3.01 XM-3.01A

T167 Washer, Limit, Round XM-3.03028350 Washer, Nylon Blade XM-3.01A

F05011-53 Washer, Split Lock, 1" XM-1.02 XM-3.02 XM-3.03F05011-9 Washer, Split Lock, 1/2" XM-2.01F05011-14 Washer, Split Lock, 1/4" XM-4.09F05011-6 Washer, Split Lock, 3/4" XM-3.02 XM-3.03 XM-3.04 XM-4.04 XM-5.01 XM-5.03F05011-27 Washer, Split Lock, 5/8" XM-3.01 XM-3.01AF05011-46 Washer, Split Lock, 7/8" XM-3.01 XM-3.01AF05011-81 Washer, Star, 9/16" XM-5.06

P844 Washer, Wave, 1 1/4” ID XM-4.07 XM-4.08P843 Washer, Wave, 1” ID XM-4.06P116 Washer, Wear, Zc XM-1.02 XM-3.03 XM-5.01 XM-5.03W397 Weight Transfer Rod Weldment, Fixed XM-1.01W483 Weight Trans Rod Wldmnt, Fxd, NXS XM-1.01W352 Wheel Arm Weldment, 13", Left XM-4.01W370 Wheel Arm Weldment, 13", Right XM-4.01W355 Wheel Arm Weldment, 16.5", Fxd, Left XM-4.03 XM-4.05W365 Wheel Arm Weldment, 16.5", Fxd, RT XM-4.03 XM-4.05W412 Wheel Arm Weldment, Sliding, Left XM-4.05W371 Wheel Arm Weldment, Sliding, Right XM-4.05A250 Wheel Assy, 13 x 5, Urethane Filled XM-4.01A150 Wheel Assembly, 9” x 3.5”, UF XM-4.06 XM-4.07 XM-4.08 XM-4.09A240 Wheel Height Gauge Assembly XM-4.11M106 Wheel Height Gauge Indicator Plate XM-4.11M105 Wheel Height Gauge Scale Plate XM-4.11P297 Wheel Hub Assembly, DM XM-4.09P291 Wheel Hub/Brng Assy, 3/4" TRB, DM XM-4.09W688 Wheel Yoke Weldment, 9” Swivel LF XM-4.06W118 Wheel Yoke Weldment, 9” Swivel RT XM-4.06W685 Wheel Yoke Weldment, Fixed, LF XM-4.08W686 Wheel Yoke Weldment, Fixed, RT XM-4.08A149 Wheel/Rim Assembly, UF XM-4.09


LasTec Articulator Owner's Manual Chapter 10: Master Parts ManualModel 721X Section 1: Mounting Hardware

10-17


Parts Manual

Section One:Mounting Hardware


Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 1: Mounting Hardware Model 721X

10-18

Figure XM-1.01: Pull Arm/Weight Transfer AssemblySerial Numbers

From: 1010295 6720397 10820798To: 6710397 (*1) 10810798 Present

Ref. No. Part No. Part No. Part No. Part Description1 W394 W394 W394 Pull Arm Weldment, Left2 W395 W395 W395 Pull Arm Weldment, Right

W397 (*2) Weight Transfer Rod Weldment, Fixed3 W483 W483 Weight Transfer Rod Weldment, Fixed, NXS4 P416 P416 P416 Spring, Compression, 2" x 6"5 P244 P244 P244 Lift Pin Assembly6 P183 P183 P183 Clevis Pin, 1" DIA x 4 1/2"7 NOT USED NOT USED 029096 Pivot Pin Weldment

P109 Bushing, Bronze, 1" ID8 P787 (*4) P787 (*4) Bushing, Steel, 1" IDP403 (*3) Bushing, Bronze, 3/4" ID9 P786 P786 Bushing, Steel, 3/4" ID

10 P114 P114 P114 Lynch Pin, 3/16"11 P113 P113 P113 Lynch Pin, 1/4"12 NOT USED T132 T132 Spacer, 1 1/4” x 1/4”13 NOT USED NOT USED F05007-27 Bolt, 3/8-16 x 3/4”14 NOT USED NOT USED F05011-4 Washer, 3/8”15 P107 P107 P107 Grease Zerk, 1/4-28 Straight

Notes(*1) Machines prior to serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installed,

should use the 6720397 to 10810798 column to order parts.

(*2) Machines before serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installedrequire the W483 Weight Transfer Rod Weldment.

(*3)Machines prior to serial number 6720397 did not require the second 3/4" bushing (illustrated)which is required for machines as of serial number 6720397. Machines prior to 6720397 whichhave had the K417 Pull Bar Upgrade Kit installed require the second bushing.

(*4)Although Machines prior to Serial Number 6720397 are originally equipped with P109 BronzeBushings, we recommend replacing them with P787 Steel Bushings. If installing steel bushingson these machines, you will also need to install T132 Spacers between the bushings and theball swivels located on the pull arms.



10-19

10

15

9

12

1 2

11

3

4

8

5

6

71413

8

Figure XM-1.01: Pull Arm/Weight Transfer Assembly



10-20

Figure XM-1.02: Pull Bar AssemblySerial Numbers

From: 1010295 1260795 1690995 6720397To: 1250795 (*1) 1680995 (*1) 6710397 (*1) Present

Ref. No. Part No. Part No. Part No. Part No. Part DescriptionW398 (*2) W398 (*2) W398 (*2) Pull Bar Weldment, XS1 W491 Pull Bar Weldment, NXS

2 F05009-36 F05009-36 F05009-36 F05009-36 Bolt, 3/4-10 x 3"3 F05011-62 F05011-62 F05011-62 F05011-62 Washer, Flat, 3/4" SAE4 F05011-29 (*3) F05011-29 (*3) F05011-29 (*3) F05011-29 (*3) Washer, Flat, 3/4"5 F05010-103 F05010-103 F05010-103 F05010-103 Nut, Nylock, 3/4-106 P116 (*4) P116 (*4) P116 (*4) P116 Washer, Wear, Zc

P109 (*5) P109 (*5) P109 (*5) Bushing, Bronze, 1" ID7 P787 (*5) Bushing, Steel, 1" ID8 F05009-69 Not Used Not Used Not Used Bolt, 1-8 x 3", G89 F05011-53 Not Used Not Used Not Used Washer, Split Lock, 1"10 Not Used T159 T159 T159 Pull Pin, SQHD, XS11 Not Used P113 P113 P113 Lynch Pin, 1/4"12 Not Used Not Used C544 C544 Pull Bar L-Pin

Notes(*1) Machines prior to serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installed,

should use column 6720397 to Present when ordering parts for this assembly.

(*2) Machines prior to serial number 6720397 which have had a K417 Pull Bar Upgrade Kit installed,require the W491 Pull Bar Weldment.

(*3) The quantity of F113 Washers will vary due to the assembly and alignment process.

(*4) Originally P115 Brass Wear Washer, has been replaced with the P116 Zinc Wear Washer. TheP115 is no longer available.

(*5)Although machines prior to serial number 6720397 used the P109 Bronze Bushing, and machines asof 6720397 used the P787 Steel Bushing, these bushings are 100% interchangeable, and you maysubstitute one for the other at your discretion.



10-21

8

9

10

11

12

1

2

3

3

4

6

5

7

Figure XM-1.02: Pull Bar Assembly



10-22

Figure XM-1.03: Bondioli PTO Shaft AssemblySerial NumbersFrom: 1010295

To: PresentRef. No. Part No. Part Description

1 P225 PTO, Bondioli, 29.9/45.1, Splined2 P258 PTO 1/2 Shaft, Female, Bondioli3 P259 PTO 1/2 Shaft, Male, Bondioli4 P273 PTO Cross Pin Assembly, Bondioli5 P272 PTO Twist Sleeve Assembly, Bondioli6 P260 PTO Yoke Assembly, Twist Release, Female Side, Bondioli7 P262 PTO Cross Bearing Assembly, Bondioli8 P263 PTO Female Shaft Yoke, Bondioli9 P265 PTO Female Shaft Yoke Pin, Bondioli10 P270 PTO Outer Shield Bearing, Bondioli11 P274 PTO Shaft, Female, Bondioli12 P267 PTO Greasing Collar, Bondioli13 P276 PTO Yoke Shield, Female Side, Bondioli14 P277 PTO Outer Shaft Shield, Bondioli15 P256 PTO Shield Retaining Chain, Bondioli16 P275 PTO Shaft, Male, Bondioli17 P271 PTO Inner Shield Bearing, Bondioli18 P264 PTO Male Shaft Yoke, Bondioli19 P266 PTO Male Shaft Yoke Pin, Bondioli20 P261 PTO Yoke Assembly, Twist Release, Male Side, Bondioli21 P279 PTO Inner Shaft Shield, Bondioli22 P278 PTO Yoke Shield, Male Side, Bondioli23 P268 PTO Outer Shield Assembly, Bondioli24 P269 PTO Inner Shield Assembly, Bondioli25 P294 Grease Zerk, 1/4-28, 45°



10-23

9

15

8

5 25

25

10 11

1314

16

23

24 2122

17 18

19

15

12

1

2

3

4

4

7

7

5

6

20

PTO Figure XM-1.03: Bondioli PTO Shaft Assembly



10-24


LasTec Articulator Owner's Manual Chapter 10: Master Parts ManualModel 721X Section 2: Gearbox

10-25


Parts Manual

Section Two:Gearbox


Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 2: Gearbox Model 721X

10-26

Figure XM-2.01: Gearbox AssemblySerial Numbers

From: 1010295 1610895 6710397To: 1600895 6700297 Present

Ref. No. Part No. Part No. Part No. Part Description1 P300 P300 P300 Gearbox, SGCM500SAR21, StBv, Splined2 W399 W399 W399 Gearbox Channel Weldment, XS3 P417 P417 P417 Delrin Wear Pad, 1" ID x 8" DIA4 P109 P109 P109 Bushing, Bronze, 1" ID5 F05010-109 F05010-109 F05010-109 Nut, Nylock, 1"-86 F05008-37 F05008-37 F05008-37 Bolt, 1/2-13 x 1 1/4"7 F05011-9 F05011-9 F05011-9 Washer, Split Lock, 1/2"8 P419 (*1) P419 (*1) P419 (*1) Bushing Assembly, Split Taper, 1 3/8" ID x B9 F05009-67 F05009-67 F05009-67 Bolt, 1/4-20 x 3/4 ", G810 P406 (*2) P406 (*2) P406 (*2) Key, 1/2" x 1/4" x 3/4"11 P437 P437 P437 Key, 5/16" SQ x 1 3/4"12 W400 W400 W400 Cover Weldment, Drive Pulley13 F05006-1 F05006-1 F05006-1 Bolt, 5/16-18 x 1"14 F05011-16 F05011-16 F05011-16 Washer, Flat, 5/16"15 P418 P418 P418 Pulley, Drive, 2B5V15416 P450 P450 P450 Belt, B-58 Insta-Power17 P737 (*3) P737 (*3) P737 Bushing, Bronze, 1" ID x 3/4"18 W424 (*4) NOT USED (*4) NOT USED (*4) Hydraulic Hose Support Loop Weldment

Notes(*1) The P419 Split Taper Bushing Assembly includes the F05009-67 Bolts & the P406 Key. The P419 does

NOT include the P437 key.

(*2) In some cases, the P419 Bushing has a key machined into the body of the bushing, making the P406Key unnecessary.

(*3) The P737 Bushing was not standard on machines prior to 6710397. However, It is recommended thatthey be installed on all machines.

(*4) As of serial number 1610895, the W424 Hydraulic Hose Support Loop is an integral part of the W399Gearbox Channel Weldment.



10-27

9

10

11

12

13 14

15 16

17

16

1

2

3

4

7 7

5

6 6

8

18

Figure XM-2.01: Gearbox Assembly



10-28

Figure XM-2.02: Superior Gearbox AssemblySerial Numbers

From 1010295To Present

Ref. No. Part No. Part Description1 P326 Gearbox Casting, Top2 P334 Gearbox Casting, Bottom (W/Breather)3 P333 Gearbox Cross Shaft4 P332 Gearbox Pinion Shaft5 P325 Gearbox Gear, 30 Teeth6 019662 Gearbox Bearing Race7 019663 Gearbox Bearing Cup8 P329 Gearbox Retaining Ring9 P328 Key, 5/16" SQ x 1.2"10 P303 Gearbox Seal, 1 3/8"11 P331 Gearbox Breather Plug12 P330 Gearbox Pipe Plug, 1/2" NPT13 P327 Bolt, 3/8-16 x 2 1/4", SHCS



10-29

9

88

5

10

10

11

13

12

1

2

3

4

77

7

6

6

6

XM202

Figure XM-2.02: Superior Gearbox Assembly



10-30

Figure XM-2.03: Drive Belt Idler AssemblySerial Numbers


Ref. No. Part No. Part Description1 W366 Idler Arm Weldment2 P408 Pulley, Idler3 P410 Spring, Extension, 1" x 7"4 P183 Clevis Pin, 1" DIA x 4 1/2"5 P109 Bushing, Bronze, 1" ID6 F05012-62 Hitch Pin, #2107 F05009-66 Bolt, 1/2-13 x 2 3/4", G88 F05011-2 Washer, Flat, 1/2" SAE9 F05010-8 Nut, Nylock, 1/2-1310 P294 Grease Zerk, 1/4-28, 45°



10-31

9

8

8

5

101

2

3

4

7

6

Figure XM-2.03: Drive Belt Idler Assembly



10-32


LasTec Articulator Owner's Manual Chapter 10: Master Parts ManualModel 721X Section 3: Cutting Decks

10-33


Parts Manual

Section Three:Cutting Decks


Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 3: Cutting Decks Model 721X

10-34

Figure XM-3.01: Spindle Assembly, Serial Numbers 1010295 - 12970399Serial Numbers

From: 1010295 1610895 1620895 1640895 8951297

To: 1600895 1610895 1630895 8941297 12970399Ref. No. Part No. Part No. Part No. Part No. Part No. Part Description

1 P108 P108 P108 P108 P108 Grease Zerk, 1/8" NPT, Straight2 F05010-139 F05010-139 F05010-139 F05010-139 F05010-139 Nut, Hex, 7/8-143 F05011-46 F05011-46 F05011-46 F05011-46 F05011-46 Washer, Split Lock, 7/8"4 F05011-73 F05011-73 F05011-73 F05011-73 F05011-73 Washer, Flat, 7/8" SAE5 T156 (*1) T156 (*1) T156 (*1) T156 (*1) T156 (*1) Pulley, Double, XS6 P103 P103 P103 P103 P103 Bearing, Spindle, Top, 6305 RS7 P105 P105 P105 P105 P105 O-Ring, 2 1/2" ID x 2 3/4" OD

8 P104 P104 P104 P104 P104 Bearing, Spindle, Bottom, 6206TGS

9 P407 P407 P407 P407 P407 Key, 3/16" SQ x 5/8"T157 T157 Spindle, Keyed10 018309 (*2) 018309 (*2) 018309 Spindle, Extended

P128 (*3) P128 (*3) P128 (*3) P128 (*3) P128 (*3) Blade, 21", High-LiftP246 (*3) P246 (*3) P246 (*3) P246 (*3) P246 (*3) Blade, 21", Low-Lift11P322 (*3) P322 (*3) P322 (*3) P322 (*3) P322 (*3) Blade, 21", Gator Mulching

12 F05011-27 (*5) F05011-27 (*5) F05011-27 (*5) F05011-27 (*5) F05011-27 (*5) Washer, Split Lock, 5/8"F05008-95 F05008-95 F05008-95 Bolt, 5/8-18 x 1 1/4"13 F05009-80 (*4) F05009-80 (*4) Bolt, 5/8-18 x 2 1/4"

14 T160 (*1) T160 (*1) T160 (*1) T160 (*1) T160 (*1) Pulley, Quad, XS15 P427 P427 P427 P427 P427 Belt, B-6016 NOT USED T180 (*2) NOT USED T180 (*2) NOT USED Spindle Spacer, 1"

Notes(*1) The T156 Double Pulley is utilized on decks X1 & X3 - X7. The T160 Quad Pulley is utilized on deck X2.

(*2)

Machines within this serial number range were originally equipped with T157 Spindles and T180 SpindleSpacers, which have been replaced with 018309 Extended Spindles, which do not require the T180 SpindleSpacers. The T157 & T180 are still available, but it is recommended that they be replaced with the 018309Extended Spindle on machines within this serial number series, making the T180 Spacer unnecessary. Ifconverting from T157 to 018309 Spindles, you will also need to replace the F05009-80 5/8-18 x 2 1/4” Boltswith F05008-95 5/8-18 x 1 1/4” Bolts.

(*3) All machines are equipped with P128 High-Lift Blades standard, but there are other blades available,including the P246 21" Low-Lift Blade, and the P322 21" Gator Mulching Blade.

(*4)The F05009-80 Bolt is utilized with the T157 Spindle & T180 Spindle Spacer ONLY. If you are replacing theT157 Spindle & T180 Spacer with the 018309 Extended Spindle on machines within this serial numberseries, you will also need to replace the F05008-80 Bolt with the F05008-95 Bolt in each spindle.

(*5)

Machines prior to Serial No. 1367099 utilized F05011-27 5/8" Split Lock Washers in this location. Thesehave been replaced with the F05011-40 5/8" Flat Washers and the 028350 Nylon Blade Washers (seeIllustration XM-3.01A, next page). It is recommended that all machines prior to Serial No. 1367099 beupfitted with the F05011-40 & 028350 washers on all blade bolts. To upfit your machine to the new stylewashers, order the 040250 Nylon Blade Washer Kit.

NOTE: The 018309 Extended Spindles CANNOT BE INSTALLED on machines from Serial Numbers 1010295 to1600895, or from Serial Numbers 1620895 to 1630895.



10-35

9

11

14

16

12

13

15

15

1

2

3

4

7

7

8

10

5

6

Section View Of Deck

Figure XM-3.01: Spindle AssemblySerial Numbers 1010295 - 12970399



10-36

Figure XM-3.01: Spindle Assembly, Serial Numbers 12980399 - PresentSerial Numbers

From: 12980399 13670599

To: 13660599 PresentRef. No. Part No. Part No. Part Description

1 P108 P108 Grease Zerk, 1/8" NPT, Straight2 F05010-139 F05010-139 Nut, Hex, 7/8-143 F05011-46 F05011-46 Washer, Split Lock, 7/8"4 F05011-73 F05011-73 Washer, Flat, 7/8" SAE5 T156 (*1) T156 (*1) Pulley, Double, XS6 P103 P103 Bearing, Spindle, Top, 6305 RS7 P105 P105 O-Ring, 2 1/2" ID x 2 3/4" OD8 P104 P104 Bearing, Spindle, Bottom, 6206 TGS9 P407 P407 Key, 3/16" SQ x 5/8"

T157 Spindle, Keyed10 018309 Spindle, ExtendedP128 (*3) P128 (*3) Blade, 21", High-LiftP246 (*3) P246 (*3) Blade, 21", Low-Lift11P322 (*3) P322 (*3) Blade, 21", Gator Mulching

F05011-27 (*2) Washer, Split Lock, 5/8"12 F05011-89 (*2) Washer, Flat, 5/8" ID x 2 1/2" ODF05008-95 Bolt, 5/8-18 x 1 1/4"13 F05009-80 (*4) Bolt, 5/8-18 x 2 1/4"

14 T160 (*1) T160 (*1) Pulley, Quad, XS15 P427 P427 Belt, B-6016 NOT USED (*2) 028350 (*2) Washer, Nylon Blade

Notes(*1) The T156 Double Pulley is utilized on decks X1 & X3 - X7. The T160

Quad Pulley is utilized on deck X2.

(*2)

Machines prior to Serial No. 1367099 utilized F05011-27 5/8" SplitLock Washers in this location. These have been replaced with theF05011-89 5/8" Flat Washers and the 028350 Nylon Blade Washers.It is recommended that all machines prior to Serial No. 1367099 beupfitted with the F05011-89 & 028350 washers on all blade bolts. Toupfit your machine to the new style washers, order the 040250 NylonBlade Washer Kit.

(*3)All machines are equipped with P128 High-Lift Blades standard, butthere are other blades available, including the P246 21" Low-LiftBlade, and the P322 21" Gator Mulching Blade.

(*4)

The F05009-80 Bolt is utilized with the T157 Spindle & T180 SpindleSpacer ONLY. If you are replacing the T157 Spindle & T180 Spacerwith the 018309 Extended Spindle on machines within this serialnumber series, you will also need to replace the F05008-95 Bolt withthe F05008-95 Bolt in each spindle.



10-37

9

11

14

16

12

13

15

15

1

2

3

4

7

7

7

8

8

10

5

6

Section View Of Deck

Figure XM-3.01A: Spindle AssemblySerial Numbers 12980399 - Present



10-38

Figure XM-3.02: High & Low Pivot Slide Bar AssembliesSerial Numbers

From 1010295 13820699To 13810699 Present

Ref. No. Part No. Part No. Part Description1 W358 (*1) W358 (*1) Pivot Slide Bar Weldment, 4 1/2"2 F05004-154 (*2) F05004-154 (*2) Bolt, 1-8 x 4", G83 F05009-69 (*2) F05009-69 (*2) Bolt, 1-8 x 3", G84 F05011-53 F05011-53 Washer, Split Lock, 1"5 T107 T107 Spacer, 1" ID x 1"

040249 (*3) Kit, Slide Bar Hardware Upfit6 F05010-161 Nut, 2-Way Locking Jam040249 (*3) Kit, Slide Bar Hardware Upfit7 F05011-62 Washer, Flat, 3/4" SAE040249 (*3) Kit, Slide Bar Hardware Upfit8 F05010-122 Nut, Half Nylock, 3/4-10

9 P123 P123 Grease Zerk, 1/4-28, 90°

Notes

(*1)The high & low pivot slide bar assemblies both take the same W358 Pivot Slide BarWeldment. It is simply inverted as to locate the ball swivel to either the top or bottom of thebar. Refer to Figure XM-3.06 for the proper pivot slide bar locations & orientations.

(*2) The F05009-69 Bolt & the F05004-154 Bolt are to be tightened with a torque wrench to150 Ft. Lbs.

(*3)

Machines prior to Serial No. 13820699 utilized jam nuts, hex nuts, and split lock washers inthese locations. These have been replaced with the F05010-161 2-Way Locking Nut,F05011-62 Flat Washer, and the F05010-122 Half Nylock Nut. Machines prior to13820699 should be upfitted with the new style hardware. If upfitting to the new stylehardware, order the 040249 Slide Bar Hardware Upfit Kit.



10-39

6 7 8

9 1

3

High Pivot Assembly

Low Pivot Assembly

678

91

2

4

4

5

Figure XM-3.02: High & Low Pivot Slide Bar Assemblies



10-40

Figure XM-3.03: Common Leg Pivot Slide Bar AssembliesSerial Numbers

From 1010295 7640697To 7630697 Present

Ref. No. Part No. Part No. Part Description1 W423 W423 Pivot Slide Bar Weldment, 5"

F05004-155 (*1) Bolt, 1-8 x 4 1/2", G82 F05004-132 (*1) Bolt, 1-8 x 5", G83 F05011-53 F05011-53 Washer, Split Lock, 1"4 T167 T167 Washer, Limit, Round5 T104 (*2) T104 (*2) Spacer, 1" ID x 1 3/4" OD x 1/4"6 F05010-104 F05010-104 Nut, Jam, 3/4-107 F05011-6 F05011-6 Washer, Split Lock, 3/4"8 F05010-7 F05010-7 Nut, Hex, 3/4-109 P116 (*3) P116 (*3) Washer, 1 1/16" x 1 3/4" x 1/8"10 F05010-109 F05010-109 Nut, Nylock, 1-811 P123 P123 Grease Zerk, 1/4-28, 90°

Notes(*1) The F05009-69 Bolt & the F05004-154 Bolt are to be tightened with a torque wrench to 150

Ft. Lbs.

(*2) Due to the assembly & alignment procedures, the T104 Spacer may not be required in theCommon Leg Slide Bar Assembly.

(*3) Due to the assembly & alignment procedures, the quantity & locations of the P116Washer(s) may vary.



10-41

Common Leg Pivot Assembly

Serial Numbers 1010295 - 7630697

Common Leg Pivot Assembly

Serial Numbers 7640697 - Present

2

5

6

6

7

7

8

8

14

4

3

3

9

9

11

11

10

1

2

Figure XM-3.03: Common Leg Pivot Slide Bar Assemblies



10-42

Figure XM-3.04: Deck Pivot Arm AssembliesSerial Numbers

From 1010295 6710397To 6700297 Present

Ref. No. Part No. Part No. Part Description1 W383 W383 Deck Pivot Arm Weldment, X7 (Right)2 W378 W378 Deck Pivot Arm Weldment, X6 (Left)3 W416 W416 Deck Pivot Arm Rod Weldment

F05013-71 Bolt, 3/4-10 x 2"4 F05009-36 Bolt, 3/4-10 x 3"F05009-36 Bolt, 3/4-10 x 3"5 F05009-54 Bolt, 3/4-10 x 3 1/2"

6 F05011-62 (*1) F05011-62 (*1) Washer, Flat, 3/4" SAE7 NOT USED (*2) F05010-103 (*2) Nut, Nylock, 3/4-108 P109 P109 Bushing, Bronze, 1" ID9 C506 C506 Clamping Plate, Top10 C413 C413 Clamping Plate, Side11 F05013-12 F05013-12 Bolt, 3/4-10 x 1 3/4"12 F05010-104 F05010-104 Nut, Jam, 3/4-1013 F05011-6 F05011-6 Washer, Split Lock, 3/4"14 F05010-7 F05010-7 Nut, Hex, 3/4-1015 F05012-63 F05012-63 Hitch Pin, #21616 P107 P107 Grease Zerk, 1/4-28, Straight

Notes(*1) The quantity of F05011-62 Washers may vary due to the assembly & alignment procedures.

(*2) On machines prior to serial number 6710397, the F05009-36 Bolt screwed directly intomounting plate on the deck, making the F05010-103 Nut unnecessary.



10-43

33

12

77

88

88

9

10

11

1515

1616

1314

12

12

1211

6 645

Left Right

Figure XM-3.04: Deck Pivot Arm Assemblies



10-44

Figure XM-3.05: Deck Hanger Chain AssembliesSerial Numbers


Ref. No. Part No. Part Description1 W375 Chain Weldment, Deck Hanger2 F05010-8 Nut, Nylock, 1/2-133 F05009-60 Bolt, 7/16-14 x 1 3/4", G84 F05011-43 Washer, Flat, 7/16" SAE5 F05010-135 Nut, Nylock, 7/16-14



10-45

3 3

1 1

2 2

4 4

4 45 5

4 4

Figure XM-3.05: Deck Hanger Chain Assemblies



10-46

Figure XM-3.06: Decks & Pivot Slide BarsSerial Numbers

From 1010295 1610895 1620895 1640895 6720397 7640697 12980399To 1600895 1610895 1630895 6710397 7630697 12970399 Present

Ref. No. Part No. Part No. Part No. Part No. Part No. Part No. Part No. Part Description1 (*1) (*1) (*1) (*1) (*1) (*1) (*1) Pivot Slide Bar Assy, High2 (*1) (*1) (*1) (*1) (*1) (*1) (*1) Pivot Slide Bar Assy, Low3 (*1) (*1) (*1) (*1) (*1) (*1) (*1) Pivot Slide Bar Assy, Com Leg

W340 W340 Deck Weldment, X1, 3"W440 W440 Deck Weldment, X1, 4"

W488 W488 Deck Weldment, X1, NXS4

040231 Deck Weldment, X1, DBSW341 W341 Deck Weldment, X2, 3"

W441 W441 W441 Deck Weldment, X2, 4"W531 Deck Weldment, X2, NXS+5


W442 W442 Deck Weldment, X3, 4"W489 W489 Deck Weldment, X3, NXS6

040233 Deck Weldment, X3, DBSW343 W343 Deck Weldment, X4/X5, 3"

W443 W443 W443 Deck Weldment, X4, 4"W500 Deck Weldment, X4, NXS7

040234 Deck Weldment, X4, DBSW343 W343 Deck Weldment, X4/X5, 3"

W444 W444 W444 Deck Weldment, X5, 4"W501 Deck Weldment, X5, NXS8





040237 Deck Weldment, X7, DBS

Notes(*1) Figure XM-3.06 is intended for pivot slide bar assembly location reference only. Refer to Figures XM-3.02 & XM-3.03

for individual parts & part numbers included in these assemblies.



10-47

1

3

4

5

6

3

9

10

7

8

2

2

1

Figure XM-3.06: Decks & Pivot Slide Bars



10-48

Figure XM-3.07: Belt Cover & Decal LocationsSerial Numbers


Ref. No. Part No. Part Description1 M113 Cover, Main Deck, N/C2 P425 Cover, Belt, Deck X43 P425A Cover, Belt, Deck X54 P423 Cover, Belt, Deck X15 P424 Cover, Belt, Deck X36 P422 Cover, Belt, Deck X67 P421 Cover, Belt, Deck X78 W403 Cover Weldment, Belt, Hinged, Deck X19 W404 Cover Weldment, Belt, Hinged, Deck X310 P125 Decal, Warning, "540 Max"11 P442 (*1) Decal, Warning, "Outer Decks"12 P179 Decal, Warning, "Operator's Seat"13 018008 Decal, Die-Cut, "LasTec"14 018009 Decal, Die-Cut, "Articulator"15 P117 Decal, Warning, "Hands & Feet"16 P126 Decal, Warning, "Replace Guard"

Notes

(*1)The two loose P442 "Outer Deck" Warning Decals located in the front of this manual are tobe affixed to each of the two rear fenders of the tractor, preferably near the operatingcontrols.



10-49

!!

4

3

11

11

11

7

2

1

68

9

10

16

16

15

15

15

15

15

15

11

1213

14

11

5

Figure XM-3.07: Belt Cover & Decal Locations



10-50

Figure XM-3.08: Cover AssembliesSerial Numbers

From 1010295 1550895To 1540895 Present

Ref. No. Part No. Part No. Part DescriptionM107 Cover, Main Deck, Slotted1 M113 Cover, Main Deck, N/C

2 P423 P423 Cover, Belt, Deck X13 P424 P424 Cover, Belt, Deck X34 P425 P425 Cover, Belt, Deck X45 P425A P425A Cover, Belt, Deck X56 P422 P422 Cover, Belt, Deck X67 P421 P421 Cover, Belt, Deck X78 M112 (*1) M112 (*1) Cover, Main Deck, 521X9 F05009-77 F05009-77 Screw, Wing, 3/8-16 x 5/8"10 F05011-44 F05011-44 Washer, Fender, 3/8"11 F05010-24 F05010-24 Nut, Wing, 3/8-1612 F05010-10 F05010-10 Nut, Nylock, 3/8-1613 M132 (*1) M132 (*1) Cover End Plate, Deck X1, 521X14 M130 (*1) M130 (*1) Cover End Plate, Deck X3, 521X15 C554 (*1) C554 (*1) Trim, Rubber, 9 1/2"16 F04203-11 (*1) F04203-11 (*1) Rivet, 3/16" x 1/4"17 W401 W401 Cover Mount Weldment, Belt, Deck X618 W402 W402 Cover Mount Weldment, Belt, Deck X719 P420 P420 Delrin Wear Pad, Belt Cover20 F05005-118 F05005-118 Screw, SFH, 1/4-20 x 1"21 F05011-11 F05011-11 Washer, Flat, 1/4" SAE22 F05010-69 F05010-69 Nut, Nylock, 1/4-2023 W403 W403 Cover Weldment, Belt, Hinged, Deck X124 W404 W404 Cover Weldment, Belt, Hinged, Deck X325 P436 P436 Bushing, Bronze, 1/2" ID26 P459 P459 Spring, Torsion, 180°, RH27 P430 P430 Spring, Torsion, 180°, LH28 F05010-10 F05010-10 Nut, Nylock, 3/8-1629 W414 W414 Stud Weldment, 3/8-16 x 6 ½”30 F05006-5 (*1) F05006-5 (*1) Bolt, 5/16-18 x ¾”31 F05011-17 (*1) F05011-17 (*1) Washer, Flat, 5/16” SAE32 F05010-58 (*1) F05010-58 (*1) Nut, Nylock, 5/16-1833 C510 NOT USED Cover, Pivot Arm, Deck X1/X334 F05006-1 NOT USED Bolt, 5/16-18 x 1”35 F05011-17 NOT USED Washer, Flat, 5/16” SAE

Notes

(*1)The M112 Main Deck Cover & related hardware, M130 End Plate & related hardware, &M132 End Plate & related hardware are only used on machines which have been convertedto 5 cutting decks (521X).



10-51

12

1213 14

15 15

16 16

16 16

11

1111

11

10

10

10

10

10

10

10

10

12

12

8

30

31

32

12

12

1111

10

10

10 10

12

1

2 3

4 5

24

27 27

28 28

29 29

26 27

25 25

25 25

23

9

9

10

22 22

20 20

21 21

17 18

76

19 19

3132

33

333434

343535

343535353636

33

Figure XM-3.08: Belt Covers & Hardware



10-52

Figure XM-3.09: Fender AssembliesSerial Numbers

From 1010295 1450895 6950497 11200998To 144895 6940497 11190898 Present

Ref. No. Part No. Part No. Part No. Part No. Part Description1 M140 M140 NOT USED (*2) NOT USED (*3) Fender

W417 Fender Weldment, Rear, Left2 M140 M140 NOT USED (*3) FenderW425 Fender Weldment, Rear, Center3 M140 M140 NOT USED (*3) FenderW418 Fender Weldment, Rear, Right4 M140 M140 NOT USED (*3) Fender

5 F05011-105 (*1) F05011-105 (*1) F05011-105 (*1) NOT USED (*3) Washer, Fender, 5/16” x 1/8”6 F05006-5 F05006-5 F05006-5 NOT USED (*3) Bolt, 5/16-18 x 3/4”

F05006-1 Bolt, 5/16-18 x 1”7 F05006-5 F05006-5 NOT USED (*3) Bolt, 5/16-18 x 3/4”

Notes

(*1)Machines from Serial Number 1010295 to 10810798 were equipped with F05011-50 5/16” FenderWashers on the fenders. They have been replaced with F05011-105 5/16” x 1/8” Thick Washers.We recommend that you replace these washers on all the fenders.

(*2) As of Serial Number 6950497, the front fenders are no longer used. Rear fenders only.

(*3) As of Serial Number 112000998, fenders are no longer used on the Ariculator.



10-53

1 1

2 3 4

5 5

5 5 5

7 7 7

6

6

Figure XM-3.09: Fenders & Hardware



10-54

Figure XM-3.10: Grass Chutes & Discharge ExtensionSerial Numbers

From 1010295 1550895 1760995 10820798To 1540895 1750995 10810798 Present

Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED (*1) W384 (*2) W384 W384 Grass Chute Weldment, Guarded2 NOT USED (*1) F05006-1 F05006-1 F05006-1 Bolt, 5/16-18 x 1”3 NOT USED (*1) F05011-50 F05011-50 F05011-50 Washer, Fender, 5/16”4 NOT USED (*1) F05011-16 F05011-16 F05011-16 Washer, Flat, 5/16”5 NOT USED (*1) F05010-58 F05010-58 F05010-58 Nut, Nylock, 5/16-186 W468 (*3) W468 (*3) W468 (*3) W468 (*3) Discharge Extension Weldment, 521X7 F05006-1 (*3) F05006-1 (*3) F05006-1 (*3) F05006-1 (*3) Bolt, 5/16-18 x 1”8 F05011-105 (*4) F05011-105 (*4) F05011-105 (*4) F05011-105 (*4) Washer, Fender, 5/16” x 1/8”9 F05011-16 (*3) F05011-16 (*3) F05011-16 (*3) F05011-16 (*3) Washer, Flat, 5/16”10 F05010-58 (*3) F05010-58 (*3) F05010-58 (*3) F05010-58 (*3) Nut, Nylock, 5/16-18

Notes(*1) On Machines prior to Serial Number 1550895, the grass chutes were an integral part of the cutting

decks. Removable grass chutes & related hardware were not used on these machines.

(*2)Machines prior to Serial Number 1760995 were originally equipped with M115 Grass Chutes, which didnot include the guard. The M115 has been replaced with the W384 Guarded Grass Chute. The M115 isno longer available.

(*3) The W468 Discharge Extension & related hardware are only used on machines which have beenconverted to 5 cutting heads (521X).

(*4)Machines from Serial Number 1010295 to 10810798 were equipped with F05011-50 5/16” FenderWashers on the grass chutes. They have been replaced with F05011-105 5/16” x 1/8” Thick Washers.We recommend that you replace these washers on all the grass chutes.



10-55

10

1

2

3

45

6

9

7

88

Figure XM-3.10: Grass Chutes & Discharge Extension



10-56

Figure XM-3.11: Safety ChainSerial Numbers

From: 1010295 2021095 2201195 2990296 3150296 6720397To: 2011095 2191095 2980296 (*1) 3140296 6710397 Present

Ref. No. Part No. Part No. Part No. Part No. Part No. Part DescriptionC529 NOT USED C529 Chain, Safety, 100”1

C547 NOT USED C547 C547 Chain, Safety, 78”2 P449 P449 NOT USED P449 P449 P449 Chain Snap Link, 1/4”3 NOT USED C546 NOT USED C546 NOT USED NOT USED Chain Mount Plate, Safety

Notes

(*1)On machines from Serial Number 2201195 to 2980296, the safety chain & related hardware were not standardequipment. To upfit a machine within this serial number series with a safety chain, order an A246 Safety ChainAssembly, which includes (1) C547 Chain, (2) P449 Snap Links, and (2) C546 Mounting Plates.



10-57

Deck X6 Deck X7

Deck X6 Deck X7

Deck X6 Deck X7

Deck X6 Deck X7

1






1

1

1

2 2

2

2

2

2

33

Figure XM-3.11: Safety Chain



10-58

Figure XM-3.12: 521X Deck Stabilizer Cable Assembly (*1)Serial Numbers


Ref. No. Part No. Part Description1 A324 Cable Assembly, 521X, 34”2 C550 Cable, 521X, 34”3 P468 Cable Clamp, 3/16”4 P449 Chain Snap Link, 1/4”5 F05006-83 Bolt, Eye, 5/16-18 x 1 1/4”6 F05010-17 Nut, Hex, 5/16-187 F05011-16 Washer, Flat, 5/16”8 F05010-58 Nut, Nylock, 5/16-189 C549 Cable Mount Plate10 K425 Cable Kit, 521X, 34”

Notes(*1) The Deck Stabilizer Cables & related hardware are only used on machines which have been

converted to 5 cutting decks (521X).



10-59

8 85

9 9

5

10

1

2

3 3

4 4

7 7

6 6

Figure XM-3.12: 521X Deck Stabilizer Cable Assembly



10-60

Figure XM-3.13: Grease ZerksSerial Numbers


Ref. No. Part No. Part Description1 P107 Grease Zerk, 1/4-28 Straight2 P294 Grease Zerk, 1/4-28 x 45°3 P123 Grease Zerk, 1/4-28 x 90°4 P108 Grease Zerk, 1/4” NPT Straight



10-61

1/4-28 Straight 1/4-28 x 45°

1/4-28 x 90° 1/4” NPT Straight

1 2

34

Figure XM-3.13: Grease Zerks



10-62

Figure XM-3.14: DecalsSerial Numbers


Ref. No. Part No. Part Description1 018008 Decal, Die-Cut, “LasTec”2 018009 Decal, Die-Cut, “Articulator”3 P179 Decal, Warning, “Operator’s Seat”4 P125 Decal, Warning, “540 Max”5 P126 Decal, Warning, “Replace Guards”6 P117 Decal, Warning, “Hands & Feet”7 P442 Decal, Warning, “Outer Decks”



10-63

! !

1

2

34

56

7

Figure XM-3.14: Decals



10-64


LasTec Articulator Owner's Manual Chapter 10: Master Parts ManualModel 721X Section 4: Wheels

10-63


Parts Manual

Section Four:Wheels


Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 4: Wheels Model 721X

10-64

Figure XM-4.01: 13” Tires & Pivot ArmsSerial Numbers

From 1010295 6720397To 6710397 (*1) Present (*4)

Ref. No. Part No. Part No. Part Description1 T154 NOT USED Turnbuckle Shoulder Bolt2 W419 NOT USED Turnbuckle End Weldment, 1” Fixed, LH3 T153 NOT USED Turnbuckle, 3/4-164 W420 NOT USED Turnbuckle End Weldment, 1/2”, LH

F05009-71 NOT USED Bolt, AH, 1/4-20 x 5/8", SSF05005-120 NOT USED Bolt, AH, 1/4-20 x 1", SSF05005-121 NOT USED Bolt, AH, 1/4-20 x 1 1/4", SSF05005-122 NOT USED Bolt, AH, 1/4-20 x 1 1/2", SS

5 (*2)

F05005-119 NOT USED Bolt, AH, 1/4-20 x 1 3/4", SS6 F05010-9 NOT USED Nut, Keps, 1/4-207 W352 NOT USED Wheel Arm Weldment, 13", Left8 F05012-21 NOT USED Cotter Pin, 3/16" x 1"9 P447 NOT USED Cotter Pin, 1/8" x 1 1/2"10 F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"11 P203 NOT USED Bushing, Bronze, 1 1/4" ID12 F05011-2 NOT USED Washer, Flat, 1/2" SAE13 F05010-8 NOT USED Nut, Nylock, 1/2-1314 P435 NOT USED Bushing, Bronze, 1 1/4" ID x 1"

T132 NOT USED Spacer, 1 1/4" ID x 2" OD x 1/4"15 F05011-75 NOT USED Washer, 1 1/4" ID x 1 3/4" ID x 1/8"16 P191 NOT USED Bearing Seal, 1 1/4" ID17 P190 NOT USED Tapered Roller Bearing, 1" ID18 P433 NOT USED Bearing Washer, 3/4" ID19 P434 NOT USED Nut, Castle, 3/4-1620 P195 NOT USED Hub Cap21 A250 (*3) NOT USED Wheel Assembly, 13 x 5, Urethane Filled22 P107 NOT USED Grease Zerk, 1/4-28, Straight23 M102 NOT USED Turnbuckle Guard, Fixed, Left25 W370 NOT USED Wheel Arm Weldment, 13", Right26 W353 NOT USED Turnbuckle End Weldment, 1” Fixed, RH27 W354 NOT USED Turnbuckle End Weldment, 1/2”, RH28 M101 NOT USED Turnbuckle Guard, Fixed, Right29 P289 (*3) NOT USED Bearing Race Insert, 1" ID TRB

Notes

(*1)On machines from Serial Numbers 1010295 to 2011095, the 13” tires & pivot arms areused on decks X1, X3, X6, & X7. On machines from Serial Numbers 2021095 to 6710397,the 13” tires & pivot arms are used only on decks X6 & X7.

(*2)The length of the allen head bolt will vary in each turnbuckle due to the assembly andalignment process. All five possible lengths are listed here. Simply match them with theactual bolt(s) in your turnbuckle(s).

(*3) The A240 Wheel Assembly includes (2) P289 Bearing Race Inserts.

(*4) As of Serial Number 6710397, the 13” tires & pivot arms are not used. They have beenreplaced with 9” urethane-filled wheel yoke assemblies & wheel spacers.



10-65

Wheel Arm Collar On Cutting Deck

Left

9

15

8

10

11

13

14

23

22

12

1

2

3

4

7

21

6

5

201918171716 2929

Right

Wheel Arm Collar On Cutting Deck

9

8

2625

10

111415

13

28

27

2212

1

3

21

6

5

20 19 18 17 17 1629 29

Figure XM-4.01: 13” Tires & Pivot Arms



10-66

Figure XM-4.02: Swivel Wheel Leg AssemblySerial Numbers

From: 1010295 1640895 2021095 6720397

To: 1600895 (*1) 2011095 (*2) 6710397 Present(*3)

1620895,Also: 1630895 1610895

Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED NOT USED W460 NOT USED Swivel Wheel Leg Weldment, X12 NOT USED NOT USED W461 NOT USED Swivel Wheel Leg Weldment, X33 NOT USED NOT USED P107 NOT USED Grease Zerk, 1/4-28 Straight4 NOT USED NOT USED F05013-3 NOT USED Bolt, 3/4-10 x 4"5 NOT USED NOT USED F05011-62 NOT USED Washer, Flat, 3/4" SAE6 NOT USED NOT USED F05010-103 NOT USED Nut, Nylock, 3/4-107 NOT USED NOT USED F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"8 NOT USED NOT USED F05011-75 NOT USED Washer, 1 1/4" ID x 1 3/4" OD x 1/8"

Notes

(*1)On machines from Serial Number 1010295 to 1600895, plus 1620895 & 1630895, 9” wheels were notstandard equipment. These machines were equipped with 13” tires & pivot arms on decks X1 & X3. Ifyou would like to convert a machine within this serial number range to 9” swivel wheels, order a K410Swivel Wheel Retro-Fit Kit.

(*2)On machines from Serial Number 1640895 to 2011095, plus 1610895, 9” wheels were not standardequipment. These machines were equipped with 13” tires & pivot arms on decks X1 & X3. If you wouldlike to convert a machine within this serial number range to 9” swivel wheels, order a K412 SwivelWheel Retro-Fit Kit.

(*3) As of Serial Number 6720397, the 9” swivel wheel legs are welded directly to the cutting decks, thusmaking the bolt-on legs & related hardware unnecessary.



10-67

1 2

3 3

7 7

8 8

5 5

4 45 5

6 6

Figure XM-4.02: 9” Swivel Wheel Leg Assemblies



10-68

Figure XM-4.03: 16.5” Tires & Pivot Arms (Front)Serial Numbers

From: 1010295 2031095 6950497To: 2021095 6940497 Present (*1)

Ref. No. Part No. Part No. Part Description1 W365 W365 NOT USED Wheel Arm Weldment, 16.5", Fixed, Right2 P109 P109 NOT USED Bushing, Bronze, 1" ID3 NOT USED (*2) P294 (*4) NOT USED Grease Zerk, 1/4-28, 45°4 P193 P193 NOT USED Cotter Pin, 5/32" x 1 3/4"5 F05012-21 F05012-21 NOT USED Cotter Pin, 3/16" x 1"6 F05012-23 F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"7 T154 T154 NOT USED Turnbuckle Shoulder Bolt8 W353 W353 NOT USED Turnbuckle End Weldment, 1", Fixed, RH9 T153 T153 NOT USED Turnbuckle, 3/4-1610 W354 W354 NOT USED Turnbuckle End Weldment, 1/2", RH11 F05011-2 F05011-2 NOT USED Washer, Flat, 1/2"12 F05010-8 F05010-8 NOT USED Nut, Nylock, 1/2-1313 F05010-9 F05010-9 NOT USED Nut, Keps, 1/4-20

F05009-71 F05009-71 NOT USED Bolt, AH, 1/4-20 x 5/8", SSF05005-120 F05005-120 NOT USED Bolt, AH, 1/4-20 x 1", SSF05005-121 F05005-121 NOT USED Bolt, AH, 1/4-20 x 1 1/4", SSF05005-122 F05005-122 NOT USED Bolt, AH, 1/4-20 x 1 1/2", SS

14 (*3)

F05005-119 F05005-119 NOT USED Bolt, AH, 1/4-20 x 1 3/4", SS15 P187 P187 NOT USED Tire/Rim Assembly, Pneumatic, 16.5 x 6.516 P195 P195 NOT USED Hub Cap17 P192 P192 NOT USED Nut, Castle, 1"-1418 P190 P190 NOT USED Bearing, Tapered Roller, 1" ID19 P194 P194 NOT USED Nut, Lug, 1/2-20 x 13/16" Tapered20 P289 (*4) P289 (*4) NOT USED Bearing Race Insert, 1" ID TRB21 F05004-111 (*4) F05004-111 (*4) NOT USED Stud, Press-In, 1/2-20 x 1 13/16"22 P191 P191 NOT USED Bearing Seal, 1 1/4" ID23 M101 M101 NOT USED Turnbuckle Guard, Fixed, Right24 C489 C489 NOT USED Axle25 P188 (*4) P188 (*4) NOT USED Hub Assembly, 1" ID TRB, Demountable26 W355 W355 NOT USED Wheel Arm Weldment, 16.5", Fixed, Left27 W419 W419 NOT USED Turnbuckle End Weldment, 1", Fixed, LH28 W420 W420 NOT USED Turnbuckle End Weldment, 1/2" LH29 M102 M102 NOT USED Turnbuckle Guard, Fixed, Left

Notes

(*1)On machines as of Serial Number 6950497, the 16.5” tires, pivot Arms, & turnbuckles located onthe front of the decks have been replaced with urethane-filled 9” dual wheel yoke assemblies &wheel spacers.

(*2) Machines prior to Serial Number 2031095 were not equipped with the P294 Zerk, unless the hubhas been replaced since October of 1995. All P188 Hubs now include the zerk.

(*3)The length of the allen head bolt will vary in each turnbuckle due to the assembly and alignmentprocess. All five possible lengths are listed here. Simply match them with the actual bolts usedin your turnbuckles.

(*4) The P188 Hub Assembly includes (1) P294 Grease Zerk, (2) P289 Bearing Race Inserts, & (4)F05004-111 Press-In Studs.



10-69

9

8

5

24

10

11

13

14

16

23

2122 1718

18 19

15

12

1

2

23

34

7

6 6

2020

25

9

5

27

26

28

29

24 11

13

14

16 2122

Wheel Arm Mount On Deck Wheel Arm Mount On Deck

17 181819

15

12

2

2

33 4

7

6 6

2020

25

Figure XM-4.03: 16.5” Tires & Pivot Arms (Front)



10-70

Figure XM-4.04: Dual Wheel Yoke Leg AssembliesSerial Numbers

From: 1010295 6950497 7640697To: 6940497 (*1) 7630697 Present (*2)

Ref. No. Part No. Part No. Part No. Part Description

NOT USED W478(Shown) NOT USED Dual Wheel Yoke Leg Weldment, Right

(Shown)1NOT USED W480

(Not Shown) NOT USED Dual Wheel Yoke Leg Weldment, Left(Not Shown)

NOT USED W477(Shown) NOT USED Dual Wheel Yoke Leg Mount Weldment, Right

(Shown)2NOT USED W479

(Not Shown) NOT USED Dual Wheel Yoke Leg Mount Weldment, Left(Not Shown)

3 NOT USED F05009-36 NOT USED Bolt, 3/4-10 x 3”4 NOT USED F05011-62 NOT USED Washer, Flat, 3/4” SAE5 NOT USED F05011-6 NOT USED Washer, Split Lock, 3/4”6 NOT USED F05010-7 NOT USED Nut, Hex, 3/4-107 NOT USED F05009-69 NOT USED Bolt, 1-8 x 3”8 NOT USED F05010-109 NOT USED Nut, Nylock, 1-89 NOT USED F05009-44 NOT USED Bolt, 3/4-10 x 2 1/2”10 NOT USED P107 NOT USED Grease Zerk, 1/4-28 Straight

Notes

(*1)Machines prior to Serial Number 6950497 were equipped with 16.5” tires & pivot Arms on thefront of the main deck, and the bolt-on dual wheel yoke legs are not used. If you would like toconvert your machine to dual wheel yokes, order a K450 Dual Wheel Retro-Fit Kit.

(*2) As of Serial Number 7640697, the dual wheel legs are welded directly to the deck, and the bolt-on dual wheel yoke legs are no longer used.



10-71

9

5

10

1

2

3

7

68

4

5 6

Figure XM-4.04: Dual Wheel Yoke Leg Assemblies



10-72

Figure XM-4.05: 16.5” Tires & Pivot Arms (Rear)Serial Numbers

From: 1010295 1450895 2031095

To: 1450895 2021095 PresentRef. No. Part No. Part No. Part No. Part Description

W371 Wheel Arm Weldment, Sliding, Right1

W365 W365 Wheel Arm Weldment, Fixed, RightW412 Wheel Arm Weldment, Sliding, Left2 W355 W355 Wheel Arm Weldment, Fixed, Left

3 P203 P203 P203 Bushing, Bronze, 1 1/4”4 P294 P294 P294 Grease Zerk, 1/4-28, 45°5 P193 P193 P193 Cotter Pin, 5/32” x 1 3/4”6 F05012-21 F05012-21 F05012-21 Cotter Pin, 3/16” x 1”7 W415 (*4) W415 (*4) W415 (*4) Axle Weldment, Flagged8 F05005-120 (*4) F05005-120 (*4) F05005-120 (*4) Bolt, Allen Head, 1/4-20 x 1”, SS9 F05011-11 (*4) F05011-11 (*4) F05011-11 (*4) Washer, Flat, 1/4” SAE10 T154 T154 T154 Turnbuckle Shoulder Bolt11 F05010-8 F05010-8 F05010-8 Nut, Nylock, 1/2-1312 F05011-2 F05011-2 F05011-2 Washer, Flat, 1/2”

W357 Turnbuckle End Weldment, Sliding, RH13 W353 W353 Turnbuckle End Weldment, 1” Fixed, RHW421 Turnbuckle End Weldment, Sliding, LH

14W419 W419 Turnbuckle End Weldment, 1” Fixed, LH

15 T153 T153 T153 Turnbuckle, 3/4-1616 W354 W354 W354 Turnbuckle End Weldment, 1/2”, RH17 W420 W420 W420 Turnbuckle End Weldment, 1/2”, LH

F05009-71 F05009-71 F05009-71 Bolt, AH, 1/4-20 x 5/8", SSF05005-120 F05005-120 F05005-120 Bolt, AH, 1/4-20 x 1", SSF05005-121 F05005-121 F05005-121 Bolt, AH, 1/4-20 x 1 1/4", SSF05005-122 F05005-122 F05005-122 Bolt, AH, 1/4-20 x 1 1/2", SS

18 (*1)

F05005-119 F05005-119 F05005-119 Bolt, AH, 1/4-20 x 1 3/4", SS19 F05010-93 F05010-93 F05010-93 Nut, Keps, 1/4-2020 P191 P191 P191 Bearing Seal, 1 1/4” ID21 P190 P190 P190 Bearing, Tapered Roller, 1” ID22 P289 P289 P289 Bearing Race Insert23 F05004-111 F05004-111 F05004-111 Stud, Press-In, 1/2-20 x 1 13/16”24 P188 (*2) P188 (*2) P188 (*2) Wheel Hub Assembly, 1” TRB, DM25 P187 P187 P187 Tire/Rim Assembly, Pneumatic, 16.5”26 P194 P194 P194 Nut, Lug, 1/2-20 x 13/16”, Tapered27 P192 P192 P192 Nut, Castle, 1”-1428 P195 P195 P195 Hub Cap

M103 Turnbuckle Guard, Sliding, Right29 M101 M101 Turnbuckle Guard, Fixed, RightM104 Turnbuckle Guard, Sliding, Left30 M102 M102 Turnbuckle Guard, Fixed, Left

31 NOT USED (*3) NOT USED (*3) P294 Grease Zerk, 1/4-28, 45°32 C489 (*4) C489 (*4) C489 (*4) Axle, Drilled33 F05012-23 (*4) F05012-23 (*4) F05012-23 (*4) Cotter Pin, 3/16" x 1 1/5"

Notes

(*1)The length of the allen head bolt will vary in each turnbuckle due to the assembly andalignment process. All five possible lengths are listed here. Simply match them with theactual bolts used in your turnbuckles.

(*2) The P188 Wheel Hub includes (4) F05004-11 Studs, (2) P289 Inserts, & (1) P294 Zerk.

(*3)As of Serial Number 2031095, the P294 Zerk located in the P188 Hub became standardequipment. Machines prior to Serial Number 2031095 do not have this zerk unless the hubhas been replaced. All P188 Hubs now include the zerk.

(*4) The C489 Drilled Axle & hardware are used in the center wheel arm location only. The left& right wheel arms use the W415 Flagged Axle Weldment & hardware.



10-73

15 15

8

8

9

9

25 25

26 26

10 1011 11

13 14

23 23

24 24

21 2121 2127 2728 28

29 30

22 2222 22

18 18

19 19

16 17

12 12

1 2

3 3 3 3

4 4

31 31

7

7

5 55

6 620 20

Pivot Arm Mount On Deck


Left & Center

Flagged Axle (Left)

Drilled Axle (Center)

Right

RightCenterLeft


32

33 33

Figure XM-4.05: 16.5” Tires & Pivot Arms (Rear)



10-74

Figure XM-4.06: 9” Swivel Wheel Yoke AssembliesSerial Numbers

From: 1010295 2021095 2870196 6720397To: 2011095 (*1) 2860196 6710397 Present

Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED W118 W118 W118 Wheel Yoke Weldment, 9” Swivel RT2 NOT USED W688 W688 W688 Wheel Yoke Weldment, 9” Swivel LF3 NOT USED A150 A150 A150 Wheel Assembly, 9” x 3.5”, UF4 NOT USED P296 P296 P296 Bearing Spacer, 3/4” ID x 1/2”, SS5 NOT USED F05013-70 F05013-70 F05013-70 Bolt, 3/4-10 x 6 1/2”6 NOT USED NOT USED (*2) F05011-62 F05011-62 Washer, Flat, 3/4” SAE7 NOT USED F05010-103 F05010-103 F05010-103 Nut, Nylock, 3/4-108 NOT USED P109 P109 P109 Bushing, Bronze, 1” ID9 NOT USED T107 T107 T107 Spacer, 1” ID x 1”10 NOT USED T104 T104 T104 Spacer, 1” ID x 1/4”11 NOT USED NOT USED (*3) NOT USED (*3) P843 Washer, Wave, 1” ID12 NOT USED P110 P110 P110 Clevis Pin, 3/8” x 1 5/16”13 NOT USED P111 P111 P111 Ring, Kick-Out, 1” ID

Notes

(*1)Machines prior to Serial Number 2021095 did not include 9” swivel wheel yokes as standard equipment.These machines will only need 9” swivel wheel yokes & related hardware if a K410 or K412 SwivelWheel Leg Retro-Fit Kit has been installed.

(*2) Machines prior to Serial Number 2870196 did not include the F05011-62 Washers as standardequipment. However, It is recommended that they be installed on all machines.

(*3) Machines prior to Serial Number 6720397 did not include the P843 Wave Washers as standardequipment. However, it is recommended that they be installed on all machines.



10-75

8

9

10

5

11

13

12

12

3

44

67

Rear View Of Wheel Yokes

Figure XM-4.06: 9” Swivel Wheel Yoke Assemblies



10-76

Figure XM-4.07: Dual Wheel Yoke AssembliesSerial Numbers

From: 1010295 6950497To: 6940497 (*1) Present

Ref. No. Part No. Part No. Part Description1 NOT USED W476 Dual Wheel Yoke Weldment, RT2 NOT USED W482 Dual Wheel Yoke Weldment, LF3 NOT USED A150 Wheel Assembly, 9” x 3.5”, UF4 NOT USED T125 Bearing Spacer, 3/4” ID x 3/8”5 NOT USED T126 Bearing Spacer, 3/4” x 11/16”6 NOT USED W481 Axle Weldment, Dual Wheel7 NOT USED F05010-34 Nut, Nylock, 5/8-108 NOT USED P203 Bushing, Bronze, 1 1/4” ID9 NOT USED T133 Spacer, 1 1/4” ID x 1”10 NOT USED T132 Spacer, 1 1/4” ID x 1/4”11 NOT USED P844 Washer, Wave, 1 1/4” ID12 NOT USED P212 Clevis Pin, 3/8” x 2 1/8”13 NOT USED P111 Ring, Kick-Out, 1” ID

Notes

(*1)Machines prior to Serial Number 6950497 did not include the dual wheel yokes as standardequipment. These machines will only need dual wheel yokes & related hardware if a K450Dual Wheel Yoke Leg Kit has been installed.



10-77

8

9

10

5

11

13

12

12

3 3

44

67


Figure XM-4.07: Dual Wheel Yoke Assemblies



10-78

Figure XM-4.08: 9” Fixed Wheel Yoke AssembliesSerial Numbers

From: 1010295 6720397To: 6710397 (*1) Present

Ref. No. Part No. Part No. Part Description1 NOT USED W686 Wheel Yoke Weldment, Fixed, RT2 NOT USED W685 Wheel Yoke Weldment, Fixed, LF3 NOT USED A150 Wheel Assembly, 9” x 3.5”, UF4 NOT USED P296 Bearing Spacer, 3/4” ID x 1/2”, SS5 NOT USED T126 Bearing Spacer, 3/4” x 11/16”6 NOT USED F05010-122 Nut, Nylock, 3/4-107 NOT USED P109 Bushing, Bronze, 1” ID8 NOT USED T107 Spacer, 1” ID x 1”9 NOT USED T104 Spacer, 1" ID x 1/4”10 NOT USED P843 Washer, Wave, 1” ID11 NOT USED P110 Clevis Pin, 3/8” x 1 5/16”12 NOT USED P111 Ring, Kick-Out, 1” ID

Notes

(*1)Machines prior to Serial Number 6720497 did not include the 9” fixed wheel yokeassemblies & related hardware as standard equipment. They were equipped with 13” tires& pivot arms

Complete left and right yoke assemblies can be ordered under part numbers: A631 -- Wheel Yoke Assy, 9 in Fxd LF XS/ER, includes items 2 through 12A632 -- Wheel Yoke Assy, 9 in Fxd Rt XS/ER, includes Item 1 and items 3 through 12



10-79

Left Right


{

7

8

9

546

10

12

11

12

3

Figure XM-4.08: 9" Fixed Wheel Yoke Assemblies



10-80

Figure XM-4.09: 9” Wheel AssemblySerial Numbers

From: 1010295 2021095To: 2011095 (*1) Present

Ref. No. Part No. Part No. Part Description1 NOT USED A150 (*2) Wheel Assembly, 9" x 3.5", UF2 NOT USED A149 (*3) Wheel/Rim Assembly, UF3 NOT USED P291 (*4) Wheel Hub/Bearing Assembly, 3/4" TRB, DM4 NOT USED P297 (*5) Wheel Hub Assembly, DM5 NOT USED P294 Grease Zerk, 1/4-28 x 45°6 NOT USED F05004-112 Stud, Press-In, 5/16-24 x 3/4"7 NOT USED P402 Bearing Race Insert, 3/4" ID, TRB8 NOT USED P292 Bearing, Tapered Roller, 3/4" ID9 NOT USED P293 Seal, TRB, 1 1/8" ID10 NOT USED F05005-101 Bolt, 1/4-20 x 1"11 NOT USED F05011-14 Washer, Split Lock, 1/4"12 NOT USED F05010-63 Nut, Hex, 1/4-2013 NOT USED F05010-142 Nut, Lug, 5/16-24 Tapered

Notes

(*1)Machines prior to Serial Number 2021095 did not include 9” wheels as standard equipment.These machines only need 9” wheels & related hardware if a K410 or K412 Swivel WheelLeg Retro-Fit Kit, or a K450 Dual Wheel Leg Retro-Fit Kit has been installed.

(*2) The A150 Wheel Assembly includes all components illustrated.

(*3) The A149 Wheel/Rim Assembly includes (4) F05005-101 Bolts, (4) F05011-14 Washers, &(4) F05010-63 Nuts.

(*4) The P291 Wheel Hub/Bearing Assembly includes (1) P297 Wheel Hub Assembly, (2) P292Bearings, & (2) P293 Seals.

(*5) The P297 Wheel Hub Assembly includes (4) F05004-112 Studs, (2) P402 Bearing RaceInserts, & (1) P294 Grease Zerk.



10-81

7 78 89 9

5 6

10111213

4

1

2 3

Figure XM-4.09: 9” Wheel Assembly



10-82

Figure XM-4.10: Anti-Scalp Wheel AssembliesSerial Numbers

From: 1010295 7640697 7750797To: 7630697 (*1) 7740797 Present

Ref. No. Part No. Part No. Part No. Part Description1 P438 P438 P438 Anti-Scalp Wheel, 6” x 3.5” x 3/4” ID2 P122 NOT USED NOT USED Clevis Pin, 3/4” DIA x 4 1/2”3 F05012-63 NOT USED NOT USED Hitch Pin, #2164 NOT USED F05008-106 F05008-106 Bolt, 1/2-13 x 4 3/4”

NOT USED C576 (*2) Retro Anti-Scalp Roller Tube5 C575 (*3) Anti-Scalp Roller Tube6 NOT USED F05010-127 F05010-127 Nut, Half Nylock, 1/2-13

Notes

(*1)

Machines from Serial Number 1010295 to 7630697 are equipped with clevis pins and hitch pins,rather than bolts, tubes, & nuts, unless an 019693 Anti-Scalp Plate Rebuild Kit has beeninstalled. To convert a machine within this serial number range to the bolt/tube system, order aK430 Anti-Scalp Wheel Rebuild Kit. If an 019693 Kit has been installed, use the 7750797 toPresent column to order parts. If a K430 Kit has been installed, use the 7640697 to 7740797column to order parts.

(*2)Machines from Serial Number 7640697 to 7740797 are equipped with anti-scalp wheel plateswith 3/4” holes, which require the C576 Retro Anti-Scalp Roller Tube. If an 019693 Anti-ScalpPlate Rebuild Kit has been installed (which has 1/2” holes), use the 7750797 to Present columnto order parts.

(*3)Machines from Serial Number 7750797 to Present are equipped with anti-scalp wheel plateswith 1/2” holes, which require the C575 Anti-Scalp Roller Tube. Machines prior to SerialNumber 7750797, which have had an 019693 Kit installed, should use the 7750797 to Presentcolumn to order parts.



10-83

5

6

4

1

1

2

3Serial Numbers 1010295 - 7630697


Figure XM-4.10: Anti-Scalp Wheel Assemblies



10-84

Figure XM-4:11 Wheel Height Gauge Assembly (*1)Serial Numbers


Ref. No. Part No. Part Description1 A240 Wheel Height Gauge Assembly2 M105 Wheel Height Gauge Scale Plate3 F05011-74 Washer, Flat, 1/4", Teflon4 M106 Wheel Height Gauge Indicator Plate5 F05009-75 Screw, Wing, 1/4-20 x 1/2"



10-85

2345

1

1 2 3 4 5

1

Figure XM-4.11: Wheel Height Gauge Assembly



10-86


LasTec Articulator Owner's Manual Chapter 10: Master Parts ManualModel 721X Section 5: Hydraulic Lift

10-87


Parts Manual

Section Five:Hydraulic Lift


Chapter 10: Master Parts Manual LasTec Articulator Owner's ManualSection 5: Hydraulic Lift Model 721X

10-88

Figure XM-5.01: Hydraulic Lift Assembly, Serial Numbers 1010295 - 1440895Serial Numbers

From: 1010295 1450895To: 1440895 Present (*1)

Ref. No. Part No. Part No. Part Description1 P121 NOT USED Hydraulic Cylinder, PP, 3/8" NPT2 P198 NOT USED Hydraulic Fitting, 1/4" JIC-1/4" NPT, 90°3 W385 NOT USED Cylinder Pull Arm Weldment4 W392 NOT USED Cylinder Pivot Block Weldment, Left5 W390 NOT USED Cylinder Pivot Block Weldment, Right6 C444 NOT USED Cylinder Tie Rod7 W389 NOT USED Cylinder Base Weldment8 W393 NOT USED Lift Arm Weldment9 W388 NOT USED Lift Arm End Weldment, Left10 W387 NOT USED Lift Arm End Weldment, Right11 F05012-63 NOT USED Hitch Pin, #21612 F05012-23 NOT USED Cotter Pin, 3/16" x 1 1/2"13 P109 NOT USED Bushing Bronze, 1” ID14 P116 NOT USED Washer, 1 1/16" ID x 1 3/4" OD x 1/8"15 T104 NOT USED Spacer, 1" ID x 1 3/4" x 1/4"16 F05011-6 NOT USED Washer, Split Lock, 3/4"17 F05010-7 NOT USED Nut, Hex, 3/4-1018 P411 NOT USED Clevis Pin, 1" DIA x 3 1/8"19 A241 NOT USED Gas Spring Cylinder Assembly20 P443 NOT USED Gas Spring Cylinder21 P448 NOT USED Ball Stud Retaining Clip22 P444 NOT USED Ball Stud, 10 MM DIA x 5/16-18 x 1/2"23 P113 NOT USED Lynch Pin, 1/4"24 P199 NOT USED Hydraulic Fitting, 1/4” JIC – 1/4” NPT, Straight25 P223 NOT USED Hydraulic Fitting Adapter, 1/4” NPT – 3/8” NPT

Notes

(*1)Machines after Serial Number 1440895, and machines prior to 1450895, which have had aK400 Hydraulic Lift Retro-Fit Kit installed, are equipped with a new hydraulic lift assembly.Refer to Illustrations XM-5.02 & XM-5.03 for parts for the new assembly.



10-89

7

88

9

56

10

1919

4

1

2

33

8 8

3 3

7

1

6

4 5

10

22 2222

21 21 2121

2220 20

19 19

11 11

12

13

18 18

23 2313

12

1212

14

1414

1515

17 17

16 16

14

9


Deck X2

Deck X2

25 25

24

Figure XM-5.01: Hydraulic Lift Assembly



10-90

Figure XM-5.02: Hydraulic Lift Assembly, Serial Numbers 1450895 - 2011095Serial Numbers

From: 1010295 1450895 1840995To: 1440895 (*1) 1830995 2011095

Ref. No. Part No. Part No. Part No. Part Description1 NOT USED P121 P121 (*2) Hydraulic Cylinder, PP, 3/8" NPT

NOT USED P198 P198 Hydraulic Fitting, 1/4” JIC-1/4” NPT, 90°2 NOT USED Hydraulic Fitting, 1/4" JIC-3/8" NPT, 90°3 NOT USED W434 W434 Cylinder Pivot Arm Weldment, LF4 NOT USED W433 W433 Cylinder Pivot Arm Weldment, RT5 NOT USED C527 C527 Cylinder Tie Rod, 3/4"6 NOT USED W435 W435 Cylinder Base Plate Weldment7 NOT USED W432 W432 Lift Arm Weldment, 3/4-10 Thread8 NOT USED W431 W431 Lift Arm Slide Tube Weldment9 NOT USED NOT USED (*3) NOT USED (*3) Deck Lift Arm Weldment, Rear, LF10 NOT USED NOT USED (*3) NOT USED (*3) Deck Lift Arm Weldment, Rear, RT11 NOT USED P464 P464 Spring, Extension, 1 3/16" x 7 1/2"12 NOT USED W473 W473 Spring Plate Weldment, Left13 NOT USED W472 W472 Spring Plate Weldment, Right14 NOT USED P223 NOT USED (*5) Hydraulic Fitting Adapter, 1/4” NPT – 3/8” NPT

Figure XM-5.02: Hydraulic Lift Assembly, Serial Numbers 2021095 - PresentSerial Numbers

From: 2021095 2201195 2790196To: 2191195 2780196 Present

Ref. No. Part No. Part No. Part No. Part Description1 P121 (*2) P121 (*2) P121 Hydraulic Cylinder, PP, 3/8" NPT

P198 P198 Hydraulic Fitting, 1/4” JIC-1/4” NPT, 90°2 P445 Hydraulic Fitting, 1/4" JIC-3/8" NPT, 90°3 W434 W434 W434 Cylinder Pivot Arm Weldment, LF4 W433 W433 W433 Cylinder Pivot Arm Weldment, RT5 C527 C527 C527 Cylinder Tie Rod, 3/4"6 W435 W435 W435 Cylinder Base Plate Weldment7 W432 W432 W432 Lift Arm Weldment, 3/4-10 Thread8 W431 W431 W431 Lift Arm Slide Tube Weldment9 W471 W471 W471 Deck Lift Arm Weldment, Rear, LF10 W470 W470 W470 Deck Lift Arm Weldment, Rear, RT11 P464 P464 P464 Spring, Extension, 1 3/16" x 7 1/2"12 W473 NOT USED (*4) NOT USED (*4) Spring Plate Weldment, Left13 W472 NOT USED (*4) NOT USED (*4) Spring Plate Weldment, Right14 NOT USED (*5) NOT USED (*5) NOT USED (*5) Hydraulic Fitting Adapter, 1/4” NPT – 3/8” NPT

Notes

(*1)Machines prior to Serial Number 1450895 are equipped with the original hydraulic lift assembly.Refer to Illustration XM-5.01 for parts for the original assembly. Machines prior to SerialNumber 1450895 which have had a K400 Hydraulic Lift Retro-Fit Kit installed should usedcolumn 2021095 – 2191195 for parts ordering.

(*2)

Machines from Serial Number 1840995 to 2780198 were originally equipped with P200Hydraulic Cylinders, which required P198 Fittings. The P200 has been replaced with the P121Cylinder, and is no longer available. If converting from a P200 to a P121 Cylinder on machineswithin this serial number range, you will also need to order either (2) P445 Fittings or (2) P223adapters to use with your existing fittings.

(*3)Machines prior to Serial Number 2021095 did not include the W470 & W471 Rear Deck LiftArms & related hardware as standard equipment. These parts are only used if a K400Hydraulic Lift Retro-Fit Kit has been installed.

(*4) As of Serial Number 2201195, the W472 & W473 Spring Plate Weldments are integral parts ofdecks X4 & X5.

(*5) As of Serial Number 1840995, P445 3/8” NPT Fittings are used, which do not need the P2231/4” NPT – 3/8” NPT Adapters.



10-91

77

88

95

6

10 11

13

13 13

11

12

1

22

3 4


Deck X2

Deck X2




10-92

Figure XM-5.03: Hydraulic Lift Assembly, Serial Numbers 1450895 - PresentSerial Numbers

From: 1010295 1450895 2021095 2201195To: 1440895 (*1) 2011095 2191195 Present

Ref. No. Part No. Part No. Part No. Part No. Part Description1 NOT USED P121 P121 P121 Hydraulic Cylinder, PP, 3/8" NPT2 NOT USED W434 W434 W434 Cylinder Pivot Arm Weldment, LF3 NOT USED W433 W433 W433 Cylinder Pivot Arm Weldment, RT4 NOT USED C527 C527 C527 Hydraulic Cylinder Tie Rod, 3/4"5 NOT USED W435 W435 W435 Cylinder Base Plate Weldment6 NOT USED W432 W432 W432 Lift Arm Weldment, 3/4-10 Thread7 NOT USED W431 W431 W431 Lift Arm Slide Tube Weldment8 NOT USED F05013-71 F05013-71 F05013-71 Bolt, 3/4-10 x 2"9 NOT USED F05011-6 F05011-6 F05011-6 Washer, Split Lock, 3/4"10 NOT USED F05011-62 F05011-62 F05011-62 Washer, Flat, 3/4" SAE11 NOT USED P113 P113 P113 Lynch Pin, 1/4"12 NOT USED P463 P463 P463 Clevis Pin, 1" DIA x 3 1/2"13 NOT USED P116 (*2) P116 (*2) P116 (*2) Washer, 1 1/16" ID x 1 3/4" x 1/8"14 NOT USED P464 P464 P464 Spring, Extension, 1 3/16" x 7 1/2"15 NOT USED F05010-109 F05010-109 F05010-109 Nut, Nylock, 1"-816 NOT USED F05012-21 F05012-21 F05012-21 Cotter Pin, 3/16" x 1"17 NOT USED P114 P114 P114 Lynch Pin, 3/16"18 NOT USED NOT USED (*3) W470 W470 Deck Lift Arm Weldment, Rear, RT19 NOT USED NOT USED (*3) W471 W471 Deck Lift Arm Weldment, Rear, LF20 NOT USED W473 W473 NOT USED (*4) Spring Plate Weldment, Left21 NOT USED W472 W472 NOT USED (*4) Spring Plate Weldment, Right

Notes

(*1)Machines prior to Serial Number 1450895 are equipped with the original hydraulic lift assembly. Refer toIllustration XM-5.01 for parts for the original assembly. Machines prior to Serial Number 1450895 whichhave had a K400 Hydraulic Lift Retro-Fit Kit installed should used column 2021095 – 2191195 for partsordering.

(*2) The quantity of P116 Washers will vary due to the assembly & alignment process.

(*3)Machines prior to Serial Number 2021095 did not include the W470 & W471 Rear Deck Lift Arms &related hardware as standard equipment. These parts are only used if a K400 Hydraulic Lift Retro-Fit Kithas been installed.

(*4) As of Serial Number 2201195, the W472 & W473 Spring Plate Weldments are integral parts of decks X4 &X5.



10-93

Seria

l Num

bers

145

0895

- Pr

esen

t

77

88

99

5

66

1010

1010

1010

1111

1313

1313

1414

1515

1616

17

17

17

17

17

17

1918

1212

12

3

4

Dec

k X2

2021




10-94

Figure XM-5.04: Hydraulic Hose Clamp AssemblySerial Numbers

From: 1010295 1280795 1610895To: 1270795 1600895 Present

Ref. No. Part No. Part No. Part Description1 NOT USED F05015-30 F05015-30 Screw, 5/16” x 3/4”, Self-Tapping2 NOT USED P440 P440 Clamp, Hydraulic Hose, 1/2”3 W424 W424 NOT USED (*2) Hydraulic Hose Support Loop Weldment

Notes

(*1)The P440 Clamp & related hardware became standard equipment on machines as of SerialNumber 1280795. They can be added to machines prior to 1280795 by simply drilling a mounthole in the top of the cross tube.

(*2) As of serial number 1610895, the W424 Hydraulic Hose Support Loop is an integral part of theW399 Gearbox Channel Weldment.



10-95

13

22

Figure XM-5.04: Hydraulic Hose Clamp Assembly



10-96

Figure XM-5.05: Lift Cables, Serial Numbers 1010295 - 1440895Serial Numbers

From: 1010295 1450895To: 1440895 Present (*1)

Ref. No. Part No. Part No. Part Description1 P413 NOT USED Cable, Lift, X22 P414 NOT USED Cable, Lift, X1/X3

Notes

(*1)As of Serial Number 1450895, the lift cables are no longer used. On machines prior to SerialNumber 1450895, we recommend removal of these cables and installation of a K400 HydraulicLift Retro-Fit Kit.



10-97

!!

2 221 2

1

Figure XM-5.05: Lift Cables, Serial Numbers 1010295 - 1440895



10-98

Figure XM-5.06: Lift Cables Assemblies, Serial Numbers 1010295 - 1440895Serial Numbers

From: 1010295 1450895To: 1440895 Present (*2)

Ref. No. Part No. Part No. Part Description1 P413 NOT USED Cable, Lift, X22 P414 NOT USED Cable, Lift, X1/X33 F05010-147 NOT USED Nut, Hex, 9/16-124 F05011-81 NOT USED Washer, Star, 9/16"5 T161 NOT USED Cable Lift End6 F05010-149 NOT USED Nut, Nylock, 5/16-247 F05009-79 NOT USED Bolt, 5/16-18 x 2", G88 F05011-17 (*1) NOT USED Washer, Flat, 5/16"9 F05010-58 NOT USED Nut, Nylock, 5/16-1810 A235 NOT USED Cable Assembly, X1/X311 A236 NOT USED Cable Assembly, X212 F05007-135 NOT USED Bolt, 3/8-16 x 3 1/4"13 F05009-76 NOT USED Eye Bolt, 1/2-13 x 2"14 F05010-35 NOT USED Nut, Hex, 1/2-1315 F05011-61 NOT USED Washer, Flat, 3/8" SAE16 F05011-68 NOT USED Washer, Flat, 1/2"17 F05010-8 NOT USED Nut, Nylock, 1/2-1318 W422 NOT USED Cable Support Loop Weldment19 F05009-62 NOT USED Bolt, 5/16-18 x 1 1/4"20 F05011-16 NOT USED Washer, Flat, 5/16"21 F05010-58 NOT USED Nut, Nylock, 5/16-1822 F05009-70 NOT USED Bolt, 5/16-18 x 1 3/4"23 P440 NOT USED Clamp, Pipe, 1/2"24 C377 NOT USED Cable Retainer Spacer Tube25 F05010-10 NOT USED Nut, Nylock, 3/8-16

Notes(*1) The quantity and location of the F05011-17 Washers will vary due to the assembly and

alignment process.

(*2)As of Serial Number 1450895, the lift cables are no longer used. On machines prior to SerialNumber 1450895, we recommend removal of these cables and installation of a K400 HydraulicLift Retro-Fit Kit.



10-99

7

8 8

8

9 9

5

6

13

13

10

11 17

18

18

19

1612

14

15

1

1

1

2

2

2

2

2

3

3

4

20

23

22

2121

1, 2

Figure XM-5.06: Lift Cables, Serial Numbers 1010295 - 1440895



10-100


Documents

721X owner ops - Lastecgateway.lastec.com/manuals/Parts/721xmas.pdf · Chapter 10: Parts Manual LasTec Articulator Owner Manual Parts Index Model 721X 10-6 Parts Index Listed By Part