Upload
tung-sen
View
232
Download
0
Embed Size (px)
Citation preview
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 1/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 1 of 51
Ki m tra UMTS Node B’s s d ng Racal Instruments Wireless Solutions 6413A.
S: AN05/0006
Sn phm: 6413A
Ban hành: 13/04/2005
Phiên bn: 1.2
Phân phi: T t c
Tóm t t Tài liu này hưng dn kim tra UMTS Node B s dng máy ño 6413A.
H tr
Thông tin liên h:
Americas Help Desk Fax: +1 949 579 1199Phone: +1 800 835 2350E-Mail: [email protected]
UK/Europe Help Desk Fax: +44 (0) 1628 662017Phone: +44 (0) 8706 080134E-Mail [email protected]
Hong Kong/APAC Help Desk Fax: +852 2834 5364Phone: +852 2832 7988E-Mail: [email protected]
© Copyright 2005 Aeroflex. All rights reserved.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 2/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 2 of 51
M C L C TÓM TT..............................................................................................................................................................1 H TR ................................................................................................................................................................1 GII THIU………………………………. .............................................................................................................3 CU HÌNH H THNG CHUNG..........................................................................................................................3 TH TC KIM TRA CHUNG……. ....................................................................................................................4 THIT LP THÔNG S CHUNG CA 6413A……………...................................................................................5 CU HÌNH GIAO DIN IUB ………….................................................................................................................9 THC HIN KIM TRA MÁY THU ...................................................................................................................13 THC HIN KIM TRA MÁY PHÁT…..............................................................................................................17
CÁC CHC NĂNG ðC BIT ......................................................................................................................18 ðA CH ð .......................................................................................................................................................................19BIU ð PHÂN TÍCH QUANG PH..............................................................................................................................20
TRÌNH T KIM TRA........................................................................................................................................25 TIÊU ð KT QU ..........................................................................................................................................28 KT QU KIM TRA.......................................................................................................................................29 TÙY CHN.........................................................................................................................................................33 TR GIÚP...........................................................................................................................................................34 THOÁT.............................................................................................................................................................35 PH LC .........................................................................................................................................................36
CÁC THÔNG S KIM TRA MÁY THU..........................................................................................................................36CU HÌNH GIAO DIN IUB...........................................................................................................................................36
CÁC THÔNG S KIM TRA MÁY PHÁT.........................................................................................................................37
ð NHY CHUN GC…….......................................................................................................................................37DI ðNG……............................................................................................................................................................38CÔNG SUT BĂNG THÔNG UPLINK.........................................................................................................................39ð NHY TUYT ðI……………………….................................................................................................................40
CÁC THÔNG S KIM TRA MÁY PHÁT........................................................................................................................41CÔNG SUT RA CC ðI (MOP)................................................................................................................................41ð LN VECTOR LI (EVM) ................................................................................................................................42LI PEAK CODE DOMAIN (PCDE) ..............................................................................................................................43LI TN S (FE) ................................................................................................................................................44ð CHÍNH XÁC CÔNG SUT CPICH (CPICH)...........................................................................................................45T L RÒ KÊNH LÂN CN (ACLR) .................................................................................................................46ð CHÍNH XÁC CÔNG SUT CPICH TUYT ðI...................................................................................................47BĂNG THÔNG B CHIM.........................................................................................................................................48
CÁC THÔNG S CHO CHC NĂNG ðC BIT.............................................................................................................49ðA CH ð ...................................................................................................................................................................49ðA CH ð (TIP).....................................................................................................................................................50BIU ð PHÂN TÍCH QUANG PH.........................................................................................................................51
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 3/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 3 of 51
Gi i thi u
Ghi chú này ñưc da trên phn mm 6413A phiên bn phát hành 2,21. ðây là mt hưng dn ñy ñ v vickim tra UMTS Node B bng cách s dng 6413A.
Hưng dn này ñưc chia thành 2 phn. Phn ñu bao gm tt c các chc năng ca 6413A, bao gm c victhit lp các thông s chung, chy mt bài kim tra và lưu li báo cáo th nghim, mà không ñ cp chi tit v vic la chn các thông s c th
Phn th hai, các Ph lc, bao gm các bng trên các thông s áp dng cho các th nghim khác nhau.
C u hình h th ng chung
ð ñơn gin, tài liu này gi ñnh rng các kt ni Iub ñn Node B là thông qua mt liên kt E1 duy nht.
H thng 6413A cũng có th ñưc cu hình ñ h tr T1 và J1 tiêu chun, cũng như IMA giao thc chy trênlên ñn 8 kt ni E1, T1 hoc J1.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 5/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 5 of 51
Thi t l p các tham s chung c a 6413A
n Global Parameters, nút trên cùng bên trái
Hình 1: Main menu
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 6/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 6 of 51
Màn hình này cho phép ngưi dùng ñnh ngh ĩ a tt c các thông s toàn cu liên quan ñn Node B ñưckim tra. Ngưi dùng có th vào các mc khác nhau bng cách n vào các mc (i), hoc dùng nút up vàdown phía bên phi (ii).
Khi các mc ñưc chn, mt ca s vi các tùy chn s ñưc m ra (iii), hoc mt bàn phím s s hin racho phép ngưi dùng nhp vào mt giá tr mong mun (ii trên hình 3).
Hình 2: Cu hình chung
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 8/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 8 of 51
Dưi ñây là danh sách Các thông s chung
Tên Mc ñnh ðơn v (Nu có) Tùy chn ðnh ngh ĩ a Khu vc ITU 1 1, 2, 3 Các khu vc th nghim ca Node B.
ITU khu vc 1 bao gm châu Âu, Trungðông, châu Phi và Bc ÁITU khu vc 2 bao gm Bc và NamM, vùng Caribbean và GreenlandITU khu vc 3 bao gm khu vc Nam Á,Australia, New Zealand và châu ðiDương
Nhà sn xut Nhà sn xut ca Node B *Model Model ca Node B Phiên bn phn mm Phiên bn phn mm ca Node B
ðánh giá công sut ra 42 dBm 0: 0.1 :100 Công sut ñu ra ca Node B.
Tn hao ngoài Uplink 0 dB 0: 0.01 :50 Tn hao cáp gia Node B's Rx và 6413A
Tn hao ngoài Downlink 0 dB 0: 0.01 :50 Tn hao cáp gia Node B's Tx và 6413A
Nu mt giá tr nhp vào hp thoi thông s chung nm ngoài phm vi, tin nhn s bt lên ñ cnh báongưi s dng (ví d dưi ñây).
Hình 4: Thông báo giá tr nhp vàongoài phm vi
Khi hoàn tt, nhn Exit phía dưi bên phi ñ lưu các thông s vào h thng và tip tc.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 9/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 9 of 51
C u hình giao di n IUB
T màn hình chính, nhn vào nút Functional Tests phía bên trái ngay dưi nút Global Parameters.
Hình 5: Main menu
Chn Configure IUB Interface (Các ch c n ăng ñ ánh d u có s n trên phiên b n ph n m m hi n t i), vàchn Edit Test Parameters phía dưi cùng bên phi.
Hình 6: Functional Tests menu
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 10/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 10 of 51
Nhp các thông s th nghim áp dng vi Node B. Giao din ngưi dùng tương t như trang Cu hìnhchung. Tham kho danh sách các tham s và ñnh ngh ĩ a ca chúng trong phn Ph lc.
Hình 7: Thông s thit lp giao din Iub
Khi tt c các thông s cn thit ñ cu hình giao din Iub (ATM) ñã ñưc nhp, nhn nút Run Test (ii) ñ btñu quá trình giao tip gia 6413A và Node B. Quá trình kim tra này ñ chính xác hot ñng Iub ca Node B.Trong quá trình kim tra, màn hình ca 6413A hin th quá trình kim tra như hình dưi ñây. Lưu ý rng hu htcác quá trình kim tra trên 6413A có mt trình t hin th tương t ca màn hình trong quá trình thc hin cácth nghim.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 11/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 11 of 51
When the test is running, the first screen informs user of the expected RF connection between the Node B andthe 6413A. In addition, it also informs the user about the test progress.
Hình 8: Starting a test (in this case Iub configuration)
Khi các th nghim ñưc tin hành, màn hình s thay ñi thành màn hình chy ñơn gin. Các ñim nhp nháymàu xanh lá cây (i) cho bit th nghim ñang chy và thanh trng thái phía dưi ca màn hình (ii) cho thytin ñ th nghim. Ngưi dùng có th ngng th nghim bng cách nhn vào nút Stop Test.
Hình 9: ðang chy cu hình Iub
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 12/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 12 of 51
Khi th nghim ñã hoàn tt, hoc khi ngng kim tra, ngưi s dng có th thoát khi màn hình kimtra bng cách nhn nút Exit.
Hình 10: Cu hình Iub hoàn tt
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 13/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 13 of 51
Th c hi n các th nghi m máy thu
Kh năng thc hin các th nghim máy thu là mt trong các chc năng chính ca 6413A. Các th nghim bênthu sau có trong phiên bn phn mm 2.21:
• ð nhy cm chun gc (TS 25.141 section 7.2) • Di ñng (TS 25.141 section 7.3) • ð nhy tuyt ñi (Additional Test )• Công sut băng rng (Additional Test)
Sau khi các thông s chung và cu hình giao din Iub ñưc thit lp xong, ngưi dùng có th thc hinbt ký th nghim nào mà h thng có kh năng thc hin.
Lưu ý rng 6413A gii ñiu ch ñy ñ tín hiu phát ñi t Node B ñ xác ñnh thi gian và ñng b. 6413Akhông cn ñánh du thi gian hoc bt kỳ thit b khác bên ngoài t Node B ñ thc hin ñng b.Ví d v hành mt th nghim thu, quá trình chy th nghim ñ xác ñnh ð nhy cm chun gc ca mtNode B, như ñưc ñnh ngh ĩ a trong 3GPP TS 25,141 phn 7.2, ñưc hin th dưi ñâyNút Receiver Tests nm gia phía bên trái có th truy cp t màn hình chính.
Hình 11: Chn Receiver Test
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 14/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 14 of 51
Trong menu Receiver Tests, the ngưi dùng có th chn các th nghim mun tin hành, sau ñó n nút Edit Tests Parameters phía bên phi.
Hình 12: Receiver Test menu
Trong màn hình "Ch nh sa thông s" mt s thông s ñang chuyn sang màu xám bi vì nó có liên quan ñncác thông s khác trong h thng. Chúng ñưc coi là các thông s chung và s ñưc t ñng cp nht khi cáctham s liên quan thay ñi. VD tn s liên kt Down/Up ñưc tính t giá tr ca Down/Up link UARFCN và s ñưc t ñng cp nht khi thay ñi giá tr ca Down/UP link UARFCN.
Hình 13: Parameters for Reference Sensitivity Level
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 15/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 15 of 51
Khi tt c các thông s ñã ñưc cài ñt như mong mun, có th bt ñu kim tra bng cách n vào nút RunTest. Màn hình hin th quá trình kim tra tương t như phn cu hình Iub ñã trình bày trên. Tt c các th nghim s có mt hoc nhiu màn hình hin th giá tr ca kt qu th nghim.
Hình 14: Kim tra kt ni RF
Hình 15: Kim tra ð nhy cm chun gc
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 16/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 16 of 51
Hình 16: Kim tra kt thúc
Sau khi th nghim hoàn tt, màn hình cui cùng hin th các kt qu thu ñưc.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 17/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 17 of 51
Th c hi n các th nghi m máy phát tín hi u
6413A cũng có kh năng thc hin các th nghim máy phát tín hiu
Các th nghim có sn trên các phiên bn phn mm 2.21 ñưc hin th dưi ñây, vi phn tương ng thamkho ñc ñim k thut trong 3GPP. Các th nghim khác s ñưc sn sàng cho bn phát hành sau.
• Công sut ra cc ñi (MOP) (3GPP TS 25.141 section 6.2.1) •
ð ln Vector li (EVM) (3GPP TS 25.141 section 6.7.1) • Li Peak Code Domain (PCDE) (3GPP TS 25.141 section 6.7.2) • Li tn s (FE) (3GPP TS 25.141 section 6.3) • ð chính xác công sut CPICH (CPICH) (3GPP TS 25.141 section 6.2.2) • T l rò kênh lân cn (ACLR) (3GPP TS 25.141 section 6.5.2.2) • ð chính xác CPICH tuyt ñi (Additional Test to 3GPP) • Băng thông b chim (3GPP TS 25.141 section 6.5.1)
Hình 17: Menu kim tra máy phát
Th tc ñ kim tra máy phát tương t như máy thu. Ngưi dùng la chn th nghim mun thc hin.Sau ñó n nút Edit Test Parameters ñ thay ñi các thông s. Sau ñó nhn nút Run Test ñ thc hin cácth nghim.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 18/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 18 of 51
Các ch c n ăng ñc bi t c a h th ng
Trong phiên bn hin ti, có hai chc năng ñc bit
• ða ch ñ • Biu ñ phân tích quang ph
Các chc năng khác s có trong các phiên bn sau.
Hình 18: Menu chc năng ñc bit
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 19/51
19
ða ch ñ Chc năng này cho phép thc hin 5 th nghim bên máy thu, EVM, FE, PCDE, MOP và
CPICH, ñng thi trong thi gian thc.
ðó là mt cách nhanh chóng ñ thc hin kim tra tình trng ca mt Node B. Xin lưu ý rng bi vì tt c năm th nghim ñang chy ñng thi vi các mô hình th nghim tương t, kt qu có th không gingnhư kt qu ca tng chy th nghim trong ñó là ch ñ ñc lp vi mô hình th nghim ti ưu quy ñnhti TS 25.141.ð có các kt qu chính xác, các xét nghim phát phi ñưc thc hin vi các thit lp ca riêng c th.
Hình 19: Kt qu kim tra ñach ñ
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 20/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 20 of 51
Biu ñ phân tích quang ph Chc năng này cho phép ngưi dùng xem và kim tra tín hiu ñưc truyn qua các Node B trong mintn s. ðây là mt th nghim hu ích ñ chng minh rng cell ñã ñưc thành lp trên Node B.
Hình 20: Biu ñ phân tích quangph
Có th dùng nút Auto Scale ñ thu hp hoc kéo giãn dng sóng ñ lp ñy màn hình cho phù hp.
Hình 21: Biu ñ t ñng cogiãn
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 21/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 21 of 51
6413A h tr 2 ch ñ hin th, pan và zoom . Bm nút ch ñ s chuyn gia 2 ch ñ. Khi máy ch ñ pan , ngưi dùng có th di chuyn các dng sóng theo chiu ngang hoc theo chiu dc bng cách nhn vàomàn hình cm ng ñ kéo các trc tn s công sut như hình dưi ñây.
Hình 22: Pan Mode
Khi máy ch ñ zoom , ngưi dùng có th phóng to thu nh bng cách nhn vào màn hình cm ng và kéo
trc tn s bên phi hoc trc công sut lên. ð thu nh, kéo theo trc tn s sang trái hoc trc công sutxung
Hình 23: Zoom Mode
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 22/51
22
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 23/51
Page 23 of 51
Mt ngưi dùng có th s dng chc năng Cursor ñ ñánh du các tn s quan tâm và tính toán s khác bitv tn s và công sut gia hai ñim con tr. Con tr ñưc tt theo mc ñnh, ñ kích hot chúng bm nútCursor mt ln. Mt ñưng màu xanh s xut hin gia màn hình vi mt tag ñính kèm. ðó là con tr 1.Ngưi s dng có th kéo dòng ti tn s quan tâm.Ngoài ra, có th s dng spinwheel ñ di chuyn con tr. Các tn s và công sut ca v trí con tr ñưc th hin c trong hp thoi gia các nút bm và màn hình hin th và cũng là tag gn lin vi con tr. tag này cóth ñưc thay ñi v trí lên xung dc theo con tr bng cách chn nó, gi và kéo nó.
Hình 24: Cursor 1
Bng cách nhn nút Cursor mt ln na. Con tr th hai, mt dòng màu ñ sm xut hin. Vic ñiukhin cho con tr này cũng tương t như con tr 1. S khác bit tn s tuyt ñi và s khác bit công
sut tuyt ñi s ñưc hin th trong hp thoi Delta. Nu ngưi dùng mun thay ñi v trí ca con tr 1,có th ñt ñưc ñiu ñó bng cách ñu tiên chn con tr bng cách nhn con tr 1 hoc tag ca nó, sauñó di chuyn nó ñn v trí mi.
Hình 25: Cursor 1 & 2
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 24/51
24
ð tt tt c các con tr, ch cn nhn nút Cursor mt ln na
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 25/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 25 of 51
Yes
Trình t ki m tra
Các biu ñ dưi ñây mô t cách ñ ghi li hoc chy trình t nghim thu.
Start
No
Record Test No
Sequence? Run Test
No Sequence?
Finish?
Yes Yes
Press Exit button Select Run Sequence
Finish
Select multiple Tx/Rx Tests or
Special Functions
Select sequence torun
back to Test Sequences menu
Save Sequence
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 26/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 26 of 51
Nó có th to ra các trình t kim tra cho mt danh sách các th nghim cn ñưc thc hin thưng xuyên.ð ghi li mt chui th nghim, ñu tiên n Test Sequences, nm phía dưi bên trái ca màn hình tiêuñ; sau ñó n New Sequence
Hình 26: Test Sequence menu
Bây gi thanh tiêu ñ s hin th mt ñim nhp nháy và " Recording Sequence", cho thy ñó là trong ch ñ ghi. Nhn Exit ñ tr li tiêu ñ màn hình. Ngưi s dng có th bt ñu ghi li quá trình ño kim mong munbng cách chn các bài kim tra mun chy.Quá trình này ging ht nhau ñ chy th nghim riêng, ngoi tr các bài kim tra chy màn hình s khôngñưc hin th. ði vi các xét nghim riêng, ngưi s dng có th ch nh sa các thông s th nghim chonhng th nghim và chương trình s ghi li tt c các thông s liên kt vi các xét nghim ñưc la chn.Ngưi s dng nên ñt ch ñ kim tra thông s cho tt c các bài kim tra vi ch ñ Single Shot Test .
Khi quá tringh ghi hoàn tt, tr li Test Sequences và chn Save Sequence. Mt ca s s bt lên thôngbáo cho ngưi s dng tên tp tin ca trình t kim tra và thư mc nơi mà nó s ñưc lưu tr. Ti thi ñimnày ngưi dùng có th thay ñi các ñĩ a và thư mc ñích bng cách dùng nút Up và Down Nhn Save ñ lưu các trình t
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 27/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 27 of 51
Hình 27: Save sequence
Sau ñó, ngưi dùng có th gi li trình t kim tra bng cách nhn vào nút Run Sequence, mt ca s s btlên cho phép ngưi s dng chn th t chy
Hình 28: Run Sequence
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 28/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 28 of 51
Tiêu ñk t qu
Ngưi dùng có th thay ñi tiêu ñ kt qu cho tài liu kt qu th nghim.ðiu này có th ñt ñưc bngcách chn nút Result Header trên menu chính. Mt bàn phím trên màn hình s xut hin cho phép ngưidùng nhp vào Operator Name, Comment, UUT Software Version và UUT Serial Numbers.
Hình 29: Result Header menu
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 29/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 29 of 51
K t qu ki m tra
Ngưi dùng có th xem tt c các th nghim ñưc thc hin bng cách nhn vào nút Test Results trênmàn hình tiêu ñ, nm phía trên bên phi. Kt qu kim tra s hin ra như màn hình dưi ñây:
Hình 30: Test Results menu
Trên màn hình này ngưi dùng có th xem tt c các th nghim ñã chy, ngày tháng và thi gian chy chúngvà kt qu ca th nghim. Nó cũng cho phép ngưi dùng lưu kt qu bng cách nhn nút Save. Mt ca s
tương t như ca lưu trình t th nghim s xut hin cho phép ngưi dùng la chn nơi ñ lưu các kt qu.
Hình 31: Save test result
Ngưi s dng cũng có th m các kt qu ñã lưu trưc ñó bng cách nhn nút Load. Mt ca s tương t s xut hin cho phép ngưi dùng la chn các kt qu th nghim ñưc np.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 30/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 30 of 51
Bng cách nhn vào nút Test Report, ngưi dùng có th ñc qua báo cáo kim tra chi tit tt c các th nghim ñã thc hin. Ngưi dùng có th ñc tt c bng cách kéo các báo cáo và chn các trang khácnhau bng cách s dng spinwheel hoc nút Up và Down.
Theo mc ñnh, các báo cáo ñưc thu nh như vy mà chiu rng tài liu phù hp vi ñ rng màn hình. Cóth xem toàn b trang bng cách nhn vào nút zoom. Ngoài ra, ngưi s dng có th xem các trang bng cáchnhn bt c nơi nào trên báo cáo hai ln. Bm hai ln na ñ xem trang ñó trong ch ñ mt trang.
Hình 32: Test Report in default view
Hình 33: Test Report in single page view
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 31/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 31 of 51
Hình 34: Double click anywhere to view all
Hình 35: View all test report
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 33/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 33 of 51
Tùy ch n
Trong menu Options, ngưi dùng có th chn tham chiu tn s External, Internal, Net P ho c Net F; chuynSpinwheel m hoc tt; thay ñi ch ñ kt ni RF gia ñơn và ñôi; và thay ñi cp ñ tương phn màn hình.Sau khi bt kỳ thay ñi ñã ñưc thc hin, ngưi s dng nên bm Apply góc dưi cùng bên phi áp dngcác cài ñt mi.
Hình 38: Options menu
Bên trái có 4 nút. Nút Clean Screen tt màn hình cm ng cho khong 45 giây, cho phép ngưi s dng ñ làm sch màn hình cm ng. Ch s dng vi mm khô ñ làm sch màn hình.
Nút About s hin th mt màn hình thông tin ñó cho thy tt c các phn mm, phn cng và các thông tingiy phép FLEXlm cho sn phm.
Nút Self Test s t ñng kim tra trên máy, và thông báo cho ngư i s dng ca các k t qu xét nghim t.
Kt qu t kim tra s ñư c lưu t ñng.
Nút Restore Settings s thay ñi tt c các thông s và thit lp tr li mc ñnh. Mt hp thoi cnh báo s ñưa ra yêu cu ngưi dùng ñ xác nhn quá trình.
Hình 39: Restore Setting warning
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 34/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 34 of 51
Tr giúp
6413A ñã tích hp sn chc năng tr giúp, ngưi dùng có th ñc qua ñ hiu nhng gì phi làm khi có vn ñ xy ra. Hưng dn s dng bao gm mi th t chi tit dch v h tr ca Aeroflex, làm th nào ñ hot ñng6413A, x lý s c, bo dưng và chi tit k thut sn phm.
Danh mc chính trong chc năng tr giúp rt ñơ n gin. Nút mũi tên bên trái cho phép ngưi dùng tr litrang trưc và nút Content cho phép ngưi dùng quay li phn mc lc. Các mc s ñưc chn qua cácliên kt trên mi trang.
Hình 40: Help menu
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 35/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 35 of 51
Thoát
ð thoát khi chương trình, bn ch cn nhn nút Exit trên dưi cùng bên phi. Nu chưa lưu kt qu xét nghim, mt cnh báo s ñưa ra yêu cu ngưi dùng ñ xác nhn.
Hình 41: Test Results unsaved warning
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 36/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 36 of 51
Ph l c
Ph lc này cung cp cho các danh sách ñy ñ cho mi thông s ca các bài kim tra chc năng
Lưu ý rng các thông s màu xám cho thy rng tham s không phi là ngưi s dng sa ñi trong màn hình.
min value – max value có ngh ĩ a là ngưi dùng có th nhp bt kì s nào trong khong giá tr t min value ñn max value.min value: step size : max value có ngh ĩ a là ngưi dùng có th nhp bt kì s nào trong khong giá tr t min
value ñn max value , mi bưc tăng step size .
Các thông s ñ kim tra chc năng
Cu hình giao din Iub
Tên Mc ñnh Tùy chn ðnh ngh ĩ a Path Identifier 1 1 - 4294967295 Specifies the Path identifier in ALCAP message,
defines the path transport channel ID NBAP common 1 VPI 1 0 - 255 Specifies the Virtual Path Identifier (VPI), that
NBAP will use NBAP common 1 VCI 38 0 - 65535 Specifies the Virtual Channel Identifier (VCI), that
NBAP will usel. NSAP Depends on Node B Depends on Node B Specifies the NSAP number of Node B IP over ATM VPI 1 0 - 255 Specifies the VPI for IP over ATM IP over ATM VCI 32 0 - 65535 Specifies the VCI for IP over ATM RNC side IP 10.209.128.130 Specifies the IP address for Radio Network
Controller emulator RNC side mask 255.255.255.0 Specifies the subnet mask for Radio Network
Controller emulator Node B side IP 10.209.128.128 Specifies the IP address for the Node B Node B side mask 255.255.255.0 Specifies the subnet mask for the Node B Node Synchronisation VPI 1 0 - 255 Specifies the VPI for Node Synchronisation Node Synchronisation VCI 34 0 - 65535 Specifies the VCI for Node Synchronisation Dedicated NBAP VPI 1 0 - 255 Specifies the VPI for Dedicated NBAP Dedicated NBAP VCI 40 0 - 65535 Specifies the VCI for Dedicated NBAP ALCAP VPI 1 0 - 255 Specifies the VPI for ALCAP ALCAP VCI 42 0 - 65535 Specifies the VCI for ALCAP AAL2 Traffic VPI 1 0 - 255 Specifies the VPI for AAL2 Traffic AAL2 Traffic VCI 44 0 - 65535 Specifies the VCI for AAL2 Traffic
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 37/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 37 of 51
Các thông s kim tra máy thu
ð nhy cm chun gc As defined in 3GPP TS 25.141 section 7.2.
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell Downlink
UARFCN
10700 10550 - 10850 for Region 1, 3
9650 - 9950 for Region 2
Specifies the UTRA Absolute Radio
Frequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
Uplink Scrambling Code
1000 Indicate the uplink scrambling codeused by 6413A
Uplink Power -120.3 dBm -130: 0.1 : -55 Specifies the output power of RF outon 6413A
Data Rate
12.2
kbps
Indicate the data rate of the uplinkchannel
BER Limit 0.001 0: 0.001 : 1 Specifies the BER value that shouldnot be exceeded or test will fail. Asdefined in 3GPP TS 25.141 section7.2
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter No. bits for BER measurement denotes thenumber of bits taken before a newresult is displayed. Only the lastresult will be logged.Continuous with log: Same asContinuous Mode except every testresult will be logged
No. bits for BERmeasurement
50000
bits
10^4: 10^4 : 10^9
Specifies numbers of bit to be sentfor BER test measurement.
Downlink Power 42 dBm 0: 0.1 :42 Indicates the power output by NodeB Tx
Cumulative Mode Off Off, On Enable/Disable performing testcumulatively
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 38/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 38 of 51
Di ñng
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink Primary
Scrambling Code
0 0 - 511 Specifies the primary scrambling
code for the Node B Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated bythe Uplink UARFCN
Uplink Scrambling Code
1000 Indicate the uplink scrambling codeused by 6413A
Uplink WantedSignal Power
-89.8 dBm -130 : 0.1 : -55 Specifies the Uplink Wanted SignalPower, which will affected the BER.As defined in 3GPP TS 25.141section 7.2
Interfering AWGN Absolute Power
-73 dBm/3.84MHz -130 : 0.1 : -55 Specifies the Interfering AWGNAbsolute Power, which will affectedthe BER. As defined in 3GPP TS25.141 section 7.2
Data Rate 12.2 kbps Indicate the data rate of the uplinkchannel
BER Limit 0.001 0: 0.001 : 1 Specifies the BER value that shouldnot be exceed or test will be failed.As defined in 3GPP TS 25.141section 7.2
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter No. bits for BER measurement denotes thenumber of bits taken before a newresult is displayed. Only the lastresult will be logged.Continuous with log: Same asContinuous Mode except every testresult will be logged
No. bits for BER
measurement
50000 bits 10^4: 10^4 : 10^9 Specifies numbers of bit to be sent
for BER test measurement. Downlink Power 42 dBm 0: 0.1 :42 Indicates the power output by NodeB Tx
Cumulative Mode Off Off, On Enable/Disable performing testcumulatively
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 39/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 39 of 51
Công sut băng thông Uplink
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink Primary
Scrambling Code
0 0 - 511 Specifies the primary scrambling
code for the Node B Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
Uplink Scrambling Code
1000 Indicate the uplink scrambling codeused by 6413A
Uplink Power -120.3 dBm -130: 0.1 : -55 Specifies the output power of RF outon 6413A
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter No. bits for BER measurement denotes thenumber of bits taken before a newresult is displayed. Only the lastresult will be logged. Continuouswith log: Same as ContinuousMode except every test result willbe logged
Downlink Power 42 dBm 0: 0.1 :42 Indicates the power output by NodeB Tx
Wideband PowerError Limit
2.9 dB 0: 0.1 :10
Actual Lower Limit -123.2 Together with upper limit, indicatedwhere the uplink power shouldremain within.
Actual Upper Limit -117.4 Together with lower limit, indicatedwhere the uplink power shouldremain within.
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 41/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 41 of 51
Thông s kim tra máy phát
Công sut ra cc ñi (MOP)
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell Downlink
UARFCN
10700 10550 - 10850 for Region 1, 3
9650 - 9950 for Region 2
Specifies the UTRA Absolute Radio
Frequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scrambling codefor the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute Radio Frequency Channel Number of theuplink. Equal to 5 x Uplink Frequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test w ill be run once andthe result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number of testswill be run before an average result is
displayed. Only the last result will belogged.Continuous with log: Same asContinuous Mode except every testresult will be logged
Test Model 1(16DPCH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 (-3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
Number ofAverages
1 1 - 100, infinite Indicate the machine to take how manytest result to generate the output,infinite means generate runningaverage
Downlink Power 42 dBm Indicates the power output by Node BTx
Expected Output
Power
0 dBm The expected power from Node B
Actual Lower Limit -2.7 dB Together with upper limit, indicatedwhere the output power should remainwithin. As defined in 3GPP TS 25.141section 6.2.1
Actual Upper Limit 2.7 dB Together with lower limit, indicatedwhere the output power should remainwithin. As defined in 3GPP TS 25.141section 6.2.1
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 42/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 42 of 51
ð ln Vector li (EVM)
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell Downlink UARFCN 10700 10550 - 10850 for Region 1, 3
9650 - 9950 for Region 2 Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
2110 - 2170 for Region 1, 3 Downlink Frequency 2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code 0 0 - 511 Specifies the primary scramblingcode for the Node B Uplink UARFCN 9750 9600 - 9900 for Region 1, 3
9250 - 9550 for Region 2 Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
EVM Limit 17.5 % 0: 0.1 :25 Specifies the EVM threshold, exceedsuch threshold will fail the test. Asdefined in 3GPP TS 25.141 section6.7.1.
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number of
tests will be run before an averageresult is displayed. Only the lastresult will be logged.Continuous with log: Same asContinuous Mode except every testresult will be logged
Test Model 4 (-3dBnoCPICH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 (-3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
Number of Averages 1 1 - 100, infinite Indicate the machine to take howmany test result to generate theoutput, infinite means generaterunning average
Downlink Power 39 dBm Indicates the power output by NodeB Tx
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 43/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 43 of 51
Li Peak Code Domain (PCDE) As defined in 3GPP TS 25.141 section 6.7.2.
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
PCDE Limit -33 dB -50: 0.1 : 0 Specifies the PCDE threshold,exceed such threshold will fail thetest. As defined in 3GPP TS 25.141section 6.7.2.
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number of
tests will be run before an averageresult is displayed. Only the lastresult will be logged.Continuous with log: Same asContinuous Mode except every testresult will be logged
Test Model 3 (16DPCH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 (-3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
Number ofAverages
1 1 - 100, infinite Indicate the machine to take howmany test result to generate theoutput, infinite means generaterunning average
Downlink Power 42 dBm Indicates the power output by NodeB Tx
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 44/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 44 of 51
Li tn s (FE) As defined in 3GPP TS 25.141 section 6.3.
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
AllowedFrequencyMeasurementError
12 Hz 0: 0.01 :20 Specifies the allowed frequencymeasurement error in FrequencyLimit, as defined in 3GPP TS 25.141section 6.3
Frequency Limit(ppm)
0.05 ppm 0: 0.001 :0.5 Specifies the Frequency Error inppm. As defined in 3GPP TS 25.141section 6.3
Frequency Limit(Hz)
117 Hz This value is calculated as follow:fdownlink x flimit(ppm) + ferror
exceed this limit will fail the test. Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number oftests will be run before an averageresult is displayed. Only the lastresult will be logged.Continuous with log: Same asContinuous Mode except every testresult will be logged
Test Model 3 (16DPCH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 (-3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
Number ofAverages 4 1 - 100, infinite Indicate the machine to take howmany test result to generate theoutput, infinite means generaterunning average
Downlink Power 39 dBm Indicates the power output by NodeB Tx
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 45/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 45 of 51
ð chính xác công sut CPICH (CPICH) As defined in 3GPP TS 25.141 section 6.2.2.
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number oftests will be run before an averageresult is displayed. Only the lastresult will be logged. Continuouswith log: Same as Continuous
Mode except every test result willbe logged
Test Model 2 1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 ( -3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
Number ofAverages
1 1 - 100, infinite Indicates the machine to take howmany test result to generate theoutput, infinite means generaterunning average
Expected Relative CPICH Power
0 dBm Indicates the power relative tomaximum output power, depends ontest model.
CPICH PowerError Limit
2.9 dB 0: 0.1 :10 Specifies the CPICH Power Error, exceed such error will fail the test. Asdefined in 3GPP TS 25.141 section
6.2.2 Downlink Power 42 dBm Indicates the power output by NodeB Tx
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 46/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 46 of 51
T l rò kênh lân cn (ACLR) As defined in 3GPP TS 25.141 section 6.5.2.2.
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink Primary Scrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated bythe Uplink UARFCN
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameterNumber of Averages denotes thenumber of tests will be run before anaverage result is displayed. Only thelast result will be logged.Continuous with log: Same as
Continuous Mode except every testresult will be logged
Test Model 1 (16DPCH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 (-3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
ACLR AdjacentChannel Limit
44.2 dB 0: 0.1: 100 Specifies the power level, whenexceed by Adjacent channel (5MHzoffsets both side of channelfrequency) will fail the test. Asdefined in 3GPP TS 25.141 section6.5.2.2
ACLR AlternateChannel Limit
49.2 dB 0: 0.1 :100 Specifies the power level, whenexceed by Alternative channel(10MHz offsets both side of channelfrequency) will fail the test. As
defined in 3GPP TS 25.141 section6.5.2.2 Downlink Power 42 dBm Indicates the power output by Node
B Tx
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 47/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 47 of 51
ð chính xác công sut CPICH tuyt ñi Additional Test to 3GPP
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number oftests will be run before an averageresult is displayed. Only the lastresult will be logged. Continuouswith log: Same as Continuous
Mode except every test result willbe logged
Number ofAverages
1 1 - 100, infinite Indicate the machine to take howmany test result to generate theoutput, infinite means generaterunning average
CPICH PowerError Limit
2.9 dB 0: 0.1 :10 Specifies the CPICH Power Error, exceed such error will fail the test. Asdefined in 3GPP TS 25.141 section6.2.2
Downlink Power 42 dBm Indicates the power output by NodeB Tx
Absolute CPICHPower
39 dBm -10: 0.1 :42 Specifies the power output by CPICH
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 48/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 48 of 51
Chim băng thông As defined in 3GPP TS 25.141 section 6.5.1.
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured
cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated bythe Downlink UARFCN
Downlink PrimaryScrambling Code
0 0 - 511 Specifies the primary scramblingcode for the Node B
Uplink UARFCN 9750 9600 - 9900 for Region 1, 39250 - 9550 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of theuplink. Equal to 5 x UplinkFrequency.
1920 - 1980 for Region 1, 3 Uplink Frequency 1950 MHz 1850 - 1910 for Region 2
Uplink Frequency is calculated by theUplink UARFCN
Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run onceand the result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number oftests will be run before an averageresult is displayed. Only the lastresult will be logged. Continuouswith log: Same as Continuous
Mode except every test result willbe logged
Test Model Basic Cell(no DPCH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 ( -3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used fortesting. Test models are defined in3GPP TS 25.141 section 6.1.1
Downlink Power 42 dBm Indicates the power output by NodeB Tx
OccupiedBandwidth Limit
5 MHz 1: 0.1 :10 Specifies the width of a frequency band such that, the mean poweremitted should be 0.5% of the totalmean transmitted power. As definedin 3GPP TS 25.141 section 6.5.1
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 49/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 49 of 51
Các thông s chc năng ñc bit
ða ch ñ
Name Default Units (if applicable)
Options Definitions
TX Diversity Off Off Enable/Disable TX Diversity option. Local Cell ID Not set Depends on Node B Specifies the identity of a Configured cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of the downlink.Equal to 5 x Downlink Frequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated by theDownlink UARFCN
DownlinkPrimaryScramblingCode
0 0 - 511 Specifies the primary scrambling code forthe Node B
EVM Limit 17.5 % 0: 0.1 :25 Specifies the EVM threshold, exceed suchthreshold will fail the test. As defined in3GPP TS 25.141 section 6.7.1.
AllowedFrequencyMeasurementError
12 MHz 0: 0.01 :20 Specifies the allowed frequencymeasurement error in Frequency Limit, asdefined in 3GPP TS 25.141 section 6.3
FrequencyLimit (ppm)
0.05 ppm 0: 0.001 :0.5 Specifies the Frequency Error in ppm. Asdefined in 3GPP TS 25.141 section 6.3
PCDE Limit -33 dB -50: 0.1 : 0 Specifies the PCDE threshold, exceed suchthreshold will fail the test. As defined in3GPP TS 25.141 section 6.7.2.
Frequency
Limit (Hz)
117 Hz This value is calculated as follow:
fdownlink x flimit(ppm) + ferrorexceed this limit will fail the test. Test Mode Single Single, Continuous, Continuous with log Single Mode: Test will be run once and the
result will be logged.Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number of tests will berun before an average result is displayed.Only the last result will be logged.Continuous with log: Same as ContinuousMode except every test result will be logged
Test Model 4 (-3dB noCPICH)
1 (64 DPCH), 1 (32 DPCH), 1 (16 DPCH),2, 3 (32 DPCH), 3 (16 DPCH)4 (-3dB w/ CPICH), 4 (-3dB w/o CPICH)4 (-18dB w/ CPICH), 4 (-18dB w/o CPICH)Basic Cell (no DPCH)
Specifies a test model to be used for testing.Test models are defined in 3GPP TS 25.141section 6.1.1
Number ofAverages
1 1 - 100, infinite Indicate the machine to take how many testresult to generate the output, infinite means
generate running average
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 50/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Page 50 of 51
ða ch ñ (tip)
Name Default Units (if applicable)
Options Definitions
ExpectedRelative CPICH Power
0 dBm Indicates the power relative to maximumoutput power, depends on test model.
CPICH PowerError Limit
2.9 dB 0: 0.1 :10 Specifies the CPICH Power Error, exceedsuch error will fail the test. As defined in3GPP TS 25.141 section 6.2.2
Downlink Power
39 dBm Indicates the power output by Node B Tx
Expected Output Power
0 dBm The expected power from Node B
Actual LowerLimit
-2.7 dB Together with upper limit, indicated wherethe output power should remain within. Asdefined in 3GPP TS 25.141 section 6.2.1
Actual UpperLimit
2.7 dB Together with lower limit, indicated wherethe output power should remain within. Asdefined in 3GPP TS 25.141 section 6.2.1
8/8/2019 6413 Operational Guide VI
http://slidepdf.com/reader/full/6413-operational-guide-vi 51/51
BTL môn CSðL ðin t - Nguyn Vit Chung lp ðT11-K52
Biu ñ phân tích quang ph
Name Default Units (if applicable)
Options Definitions
Local Cell ID Not set Depends on Node B Specifies the identity of a Configured cell DownlinkUARFCN
10700 10550 - 10850 for Region 1, 39650 - 9950 for Region 2
Specifies the UTRA Absolute RadioFrequency Channel Number of thedownlink. Equal to 5 x DownlinkFrequency.
Downlink 2110 - 2170 for Region 1, 3 Frequency
2140 MHz 1930 - 1990 for Region 2
Downlink Frequency is calculated by theDownlink UARFCN
Test Mode Continuous Single, Continuous, Continuous with log Single Mode: Test will be run once andthe result will be logged.
Continuous Mode: Test will be runcontinuously. The parameter Number of Averages denotes the number of tests willbe run before an average result isdisplayed. Only the last result will belogged.Continuous with log: Same as ContinuousMode except every test result will belogged
AverageLength
10 1 - 100, infinite Specifies how many trace are taken fordrawing the graph
DownlinkPower
42 dBm 0: 0.1 :42 Indicates the power output by Node B Tx