63301 OP100 OC100 OrthoID Technical Manual 4AB

03/2003 63301

Orthopantomograph®

OP100Orthoceph®

OC100Ortho ID

Technical Manual

Copyright © 2003 by Instrumentarium Imaging

Documentation, trademark and the software are copyrighted with all rightsreserved. Under the copyright laws the documentation may not be copied,photocopied, reproduced, translated, or reduced to any electronic medium ormachine readable form in whole or part, without the prior written permissionof Instrumentarium Imaging.

The original language of this manual is English.

Instrumentarium Imaging reserves the right to revise this publication fromtime to time and to make changes in the content of it without obligation tonotify any person of such revision or changes.

Manufactured by Instrumentarium ImagingP.O. Box 20FIN-04301 TuusulaFINLANDTel. +358 10 394 6500Fax. +358 10 394 6501E-mail: [email protected]: http://www.InstrumentariumImaging.com

Orthopantomograph® and Orthoceph® are registered trademarks ofInstrumentarium Corporation. U.S. patents 4,641,336; 5,016,264; 5,425,065and 5,444,754. German patent 4,344,745. Orthopantomograph® OP100 andOrthoceph® OC100 comply with UL and C-UL (File E157261).

Table of Contents
1 Introduction ........................................................................................................ 12 Setup program menu.......................................................................................... 3
2.1 Review setup parameters ......................................................................................... 32.2 Change setup parameter and exit............................................................................. 42.3 Changing parameters ............................................................................................... 4

2.3.1 Language....................................................................................................................42.3.2 Date format ................................................................................................................52.3.3 Date and time setting .................................................................................................62.3.4 Clinic data ..................................................................................................................72.3.5 Print time setting ........................................................................................................72.3.6 Service mode..............................................................................................................8

3 OP100 error message display .......................................................................... 113.1 Error messages....................................................................................................... 113.2 Error messages, english ......................................................................................... 123.3 Error messages, French.......................................................................................... 143.4 Error messager, German ........................................................................................ 163.5 Error messages, Spanish ........................................................................................ 183.6 Error messages, Italian .......................................................................................... 203.7 Error messages, Finnish......................................................................................... 223.8 Error messages, Swedish ....................................................................................... 24

4 Technical specifications.................................................................................... 275 Appendix, dialogue table.................................................................................. 296 Spare parts ........................................................................................................ 417 Wiring diagrams ............................................................................................... 45

63301-4AB Instrumentarium Imaging i

ii Instrumentarium Imaging 63301-4AB

1 Introduction

1 IntroductionOrtho ID is a desk top equipment for printing patient data and exposure datareceived from the OP100 on the x-ray film. A window type film cassette isused. The Ortho ID can be used with all OP100 and OC100 models. Someolder models require upgrading (option code 61260). This manual covers thesoftware features of the V 1.01 or higher.

The following markings and symbols may have been used in this manual:

NOTE

Contains useful information for the reader about the unit and its use.

CAUTIONContains important instructions. If these instructions are not observed,malfunction of the unit or damage to the unit or other property may occur.

WARNINGContains warnings and instructions about the safety of the unit. if thesewarnings are not respected, serious risks and injury may be caused to thepatient and operator.

Attention, consult accompanying documents.

If the unit has CE - marking it is CE-marked according to the Medical Device Directive 93/42/EEC.

Radiographic control.

63301-4AB Instrumentarium Imaging 1

1 Introduction

2 Instrumentarium Imaging 63301-4AB

2 Setup program menu

2 Setup program menuThe following parameters can be programmed for the Ortho ID:

2.1 Review setup parameters1 Enter Setup from the Normal display.

Press the “Shift” and “MENU” keyssimultaneously.

2 First setup parameter is displayed.Press “ ↑ “ or “ ↓ “ to review theprevious or next parameter. Seesection 2.3.1 for details.

3 Press “ ↓ “. Next setup option will bedisplayed. See section 2.3.2 fordetails.


ORTHO ID SETUP

Feature Options

Dialogue language version A (ROM A)

English, German, French, Spanish, Italian

Dialogue language version B (ROM B)

English, Finnish, Swedish

Date format YYMMDD, MMDDYY, DDMMYY, MM/DD/YY

Date and time setting YY, MM, DD, hh, mm, ss

Clinic data 1 to 10 dentist names, each max. 13 characters

Print time (s) 0.10, 0.12, 0.16, 0.20, 0.32, 0.40, 0.50, 0.64, 0.80, 1.00, 1.20, 1.60, 2.00, 2.50, 3.20, 4.00, 5.00, 6.40

Service Printing contrast, Display contrast, Serial Transfer Test






8 Press “ ↓ “. The first setup parameterwill be displayed again.

2.2 Change setup parameter and exit1 To change the Setup parameter, select by pressing the “OK”.

2 Follow the instructions in the Chapter 2.3. Changing Parameters.

3 Exit anytime from the Setup mode by pressing the “MENU” key.

2.3 Changing parameters

2.3.1 Language

The Ortho ID language version A can display the dialogues in English,French, German, Italian and Spanish. English, Finnish, Swedish are availablewith the language version B.

1 ROM A: Select the language versionmenu fromthe Setup menu. The cur-rent language version is displayed.“ENGLISH” is displayed, if no lan-guage version has been set before.

2 Press “OK” to enter. The selection eg.“ENGLISH” is blinking. Use “← “and “→“ keys to select other dialoguelanguages.



3 ROM B: Select the language versionmenu fromthe Setup menu. Thecurrent language version isdisplayed.“ENGLISH” is displayed, if nolanguageversion has been set before.

4 Press “OK” to store any changes into the memory.

5 Press “MENU” key anytime to exit from the Setup.

2.3.2 Date format

1 While in the Normal display pressSHIFT and menu.

2 Select the date format from the Setupmenu. Press “OK”.

3 The date format will be displayed andit is blinking. The initial setting is“YYMMDD”, where “YY” is theyear, “MM” the month and “DD” theday of the month.

NOTEThe date is not set here. Refer to the section DATE AND TIME SETTING.

4 Press “OK” or “MENU” to exit with this setting.

5 To select a different date format press“→“. “MMDDYY” will be displayedand it is blinking.

6 Press “OK” to select this format andexit for setup or

7 Press “→“. “DDMMYY” will bedisplayed and it is blinking.

8 Press “OK” to select this format andexit from Setup.

9 Press “→“. “MM/DD/YY” will bedisplayed and it is blinking.

10 Press “OK” to select this format andexit from Setup.

11 Press “MENU” key anytime to exitfrom the Setup.



2.3.3 Date and time setting

1 While in the Normal display pressSHIFT and menu.

2 Select the date and time setting fromthe Setup menu. Press “OK”.

3 Enter the date and time, as they willbe displayed.The date format will beas programmed and the time isdisplayed.

4 Press “OK” to select the date and time setting. Numbers under the datesetting will blink.Enter a new date eg. “940920” in the date formatabove. First number entered will clear the previous date. Press “OK”.

NOTE

If you press “OK” before you have entered all six numbers, the old date willbe selected. Start again.

5 Numbers under the time setting willblink. Enter a new time eg. “112200”in the date format above. First numberentered will clear the previous time.

NOTE

The clock uses 24 hours format, i.e. 2:30 p.m. is 143000 etc.

6 Press “OK”. The Date and timesetting menu is displayed again. Thetime is not shown in normal use, it isonly used for the calendar.

NOTEA beep is heard and the data field will keep blinking if a wrong date or timeentered. Enter the correct date or time and press “OK”.

7 Press “MENU” to exit from theSetup.



2.3.4 Clinic data

For each patient there is a choice of printing the name of the dental clinic orthe dentist. The difference is in the patient data entry, where permanent dentalclinic will be printed for every patient.

1 Select clinic data from the Setup menu. If the “clinic data” has been setbefore, it will be displayed on the last row.

2 Press “OK”. First dentist, if entered, isdisplayed. The cursor blinks on thelast row.

3 Edit this name by typing the newname (max. 13 characters) then press“OK”. Press CLEAR to remove thedentist name and type a new one.

4 Select next dentist by pressing first“OK”, then “ →“ key once or more.Other dentists are displayed.

5 Repeat the steps to enter other dentist names, up to ten names.

NOTEIf the date format is “MM/DD/YY”, only first 12 characters of the dentistname are displayed.

6 Press the “MENU” key to exit the Setup.

2.3.5 Print time setting

1 Select the print time from the Setupmenu. The preset print time, eg. 2.0 s,will be displayed.

2 Press “OK”. The cursor shows anumber and blinks in the last row.

3 Use “←“ and “→“ keys to select theprint time, eg. “3.2”, from the table ofpreset times: 0.10 - 0.12 - 0.16 - 0.20 -0.32 - 0.40 - 0.50 - 0.64 - 0.80 - 1.00 -1.20 - 1.60 - 2.00 - 2.50 - 3.20 -4.00 - 5.00 - 6.40.



4 Press “OK”. The Print time menu andthe new print time are displayed.

5 Review another setting or press“MENU” key to exit the Setup.

2.3.6 Service mode

The Service mode is for adjusting the display contrast and the printingcontrast of the unit and to test the OP100 serial interface. The dialoguelanguage is English.

PRINTING CONTRAST

1 Select the Service mode from theSetup. Press “OK”.

2 Press “→“ or “←“ until the displayshows PRINTING CONTRAST: anda number. Press “OK”.

3 Adjust the printing display contrast.Number on the last row will changefrom 0 to 7 and the printing displaycontrast changes.

The effect of this adjustment is seen withthe processed film.

NOTE “0” is recommended for the printing display contrast.

4 Return to the Service mode selectionby pressing the “MENU” key. Press“MENU” again to exit the Setup.

DISPLAY CONTRAST


6 Press keys “→ “ or “← “ until thedisplay shows DISPLAY CONTRASTand a number. Press “OK”.



7 Adjust the display contrast. Numberon the last row will change from 0 to 7and the display contrast changes.

NOTE “5” or 6” is recommended for the display contrast.

8 Return to the Service mode selectionby pressing the “MENU” key. Press“MENU” again to exit the Setup.

DATA TRANSFER TEST

This test program is for testing that the Ortho ID receives data from theOP100.


10 Press the key “↑“ or “↓“ until thedisplay shows DATA TRANSFER.Press “OK”.

11 Press “OK” or make the exposure.Ortho ID echoe all data received fromthe serial link on the display. Ifmiscellaneous data is on the display,the OP100 data transfer is ok.

The display may be frozen with the “Space” key and the previous datacan be scrolled with the “↑ “ and “↓“ keys.

12 Return to the Service mode selection by pressing the “MENU” key.Press “MENU” again to exit the Setup.




3 OP100 error message display

3 OP100 error message displayIn the OP100 error situation, a message is displayed on the control panel. Thesame information is also sent to the Ortho ID, where it is displayed withexplanations in selected language.

3.1 Error messages

Each error is displayed in multiple screens, each screen having four rows by20 characters, where the first screen describes the nature of the error.

1 The first row in every screen has theerror codeand “→ “ mark indicatingthat there is more information for cor-rective actions.

2 Press “→“ to have more information.Second, and sometimes the thirdscreen is displayed.



3 Pressing “→“ with the last display of information clears the screen. Theerror message is also cleared when the corrective action with the OP100is done. The Normal display is shown.

NOTE

Error code Ch 9 rEO does not have its message on the Ortho ID softwareversions 1.00 and 1.01. Only the beep is heard.

3.2 Error messages, english

1st SCREEN 2nd (3rd) SCREEN

Ch 1 CASSETTEPanoramic cassette not in place or not replaced.

Ch 1 CASSETTECheck cassette. Replace cassette.

Ch 2 CASSETTECephalostat cassette not in place or not replaced

Ch 2 CASSETTECheck cassette.Replace cassette.

Ch 3 COLLIMATORCollimator not in panoramic position.

Ch 3 COLLIMATORCheck collimator position.

Ch 4 COLLIMATORCollimator not in cephalostat position.

Ch 4 COLLIMATOR Check collimator position.

Ch 5 *** VOLTAGEline voltage out of limits. Temporary problem?

Ch 5 *** VOLTAGERetake with new film.

Ch 6 POSITIONOP100 not in start position.

Ch 6 POSITIONPan:Check collimator position.Ch 6 POSITION QA & ceph: press Movement key to align THA.

Ch 7 *** EXPOSUREExposure switch prematurely released.

Ch 7 *** EXPOSURERetake with new film.

Ch 8 PSE SERVICE2000 exposures since last preventative maintenance.

Ch 8 PSE SERVICEContact your dealer. Resume to normal OP100 operation.

Sy 20 *** WAITExposure is disabled for a moment.

Sy 20 *** WAITPlease wait. Wait time on display.

Sy 21 HOTTubehead hot. Exposure is disabled for a moment.

Sy 21 HOTPlease wait until OP100 “READY”.

Sy 22 ***GENERATORGenerator failure during exposure cycle.

Sy 22 ***GENERATORReload the cassette. Try again.

Sy 23 INVERTERTube current and voltage not rising during exposure.

Sy 23 INVERTERReload the cassette. Try again. Call service.

Sy 24 FILAMENTTube current not rising during exposure.

Sy 24 FILAMENTReload the cassette. Try again. Call service.



Sy 25 AECAEC base frequency incorrect. Call service.

Sy 25 AECNote: OP100 can be used in manual exposure mode.

Sy 26 EEPROMMemory write failed.

Sy 26 EEPROMTry again. Call service.

Sy 27 ROTATIONRotation movement problem.

Sy 27 ROTATIONTry again. Call service.

Sy 28 CASSETTECassette movement problem.

Sy 28 CASSETTETry again. Call service.

Sy 29 LINEARLinear movement problem.

Sy 29 LINEARTry again. Call service.

Sy 30 HOLDERCassette holder movement problem.

Sy 30 HOLDERTry again. Call service.

Sy 31 UP/DOWNVertical movement problem.

Sy 31 UP/DOWNTry again. Call service.

Er 40 CPUCPU processing failure.

Er 40 CPUTry again. Call service.

Er 41 CPUCPU RAM check failure.


Er 42 CPUEPROM check-sum failure at power up.


Er 43 *** VOLTAGEPower of filament Board problem.

Er 43 *** VOLTAGEDo not use OP100! Call service.

Er 44 FILAMENTTube head preheating circuit not operating.

Er 44 FILAMENTTry again. Call service.

Er 45 INPUTKeyboard or expousre key failure during power-up sequence.

Er 45 INPUTTry again. Do not press a key.

Er 46 PAYEnd of test period. Exposure prevented.

Er 46 PAY Call your dealer.




3.3 Error messages, French


Ch 1 CASSETTEPosition incorrecte ou abcence de la cassette panoramique.

Ch 1 CASSETTEVérifier la position. Insérer la cassette.

Ch 2 CASSETTEPoistion incorrecte ou absence de la cassette céphalostat.

Ch 2 CASSETTEVérifier la position. Insérer la cassette.

Ch 3 COLLIMATEURCollimatout pas en position panoramique.

Ch 3 COLLIMATEURVérifier la position du collimateur.

Ch 4 COLLIMATEURCollimatour pas en position céphalostat.

Ch 4 COLLIMATEUR Vérifier la position du collimateur.

Ch 5 ***TENSIONTension secteur hors limites. Probléme temporaire?

Ch 5 *** TENSIONFaire un noveau film.

Ch 6 POSITIONL’OP100 n’est pas en position e départ.

Ch 6 POSITIONPanoramique: Vérifier la position du collimateur.Ch 6 POSITION QA & CEPHALO: presser touche retour pour aligner générateur.

Ch 7 *** EXPOSITIONDéclencheur relaché avant la fin de léxposition.

Ch 7 *** EXPOSITIONFaire un nouveau film.

Ch 8 MAINTENANCE2000 clichés depuis derniére maintenace préventive.

Ch 8MAINTENACEContcter revendeur. Presser une touche pour utilisation.

Sy 20 *** ATTENTEDéclenchement interdit temporairement.

Sy 20 *** ATTENTEAttendre SVP le temps affiché.

Sy 21 TEMPERATUREDéclenchement interdit temporairement.

Sy 21 TEMPERATUREAttende jusqu’ à OP100 “PRET”.

Sy 22 ***GENERATEURProbléme générateur durant cycle d’exposition.

Sy 22 ***GENERATEURRechrger cassette. Essayer à nouveau.

Sy 23 INVERTEURPas de courant ni de tension pendant d’exposition.

Sy 23 INVERTEURRechrger cassette. Essayer à nouveau.

Sy 24 FILAMENTPas de courant pendant d’exposition.

Sy 24 FILAMENTRecharger cassette. Essayer à nouveau. Contacter revendeur.

Sy 25 AECFréquence de base de l’AEC icorrecte. contacter revendeur.

Sy 25 AECNOTE: l’OP100 peut s’utiliser rn mode manuel.

Sy 26 EEPROMProbléme écriture en mémoire.

Sy 26 EEPROMEssayer à nouveau. Contacter revendeur.



Sy 27 ROTATIONprobléme mouvement de rotation.

Sy 27 ROTATIONEssayer à nouveau. Contacter revendeur.

Sy 28 CASSETTEprobléme mouvement de la cassette.

Sy 28 CASSETTEEssayer á nouveau. Contacter revendeur.

Sy 29 LINEAIREProbléme mouvement linéaire.

Sy 29 LINEAIREEssayer á nouveau. Contacter revendeur.

Sy 30 SUPPORTProbléme mouvement du support cassette.

Sy 30SUPPORTEssayer á nouveau. Contacter revendeur.

Sy 31 HAUT/BASProbléme mouvement vertical.

Sy 31 HAUT/BAS Essayer á nouveau. Contacter revendeur.

Er 40 CPUprobléme de fonctionnement CPU.

Er 40 CPUEssayer á nouveau. Contacter revendeur.

Er 41 CPUProbléme de vérification RAM.


Er 42 CPUprobléme de vérification check-sum.


Er 43 *** TENSIONprobléme de carte puissance ou filament.

Er 43 *** TENSIONNE PAS UTILISER L’OP100! Contacter revendeur.

Er 44 FILAMENTProbléme du circuit de pré-chauffage.

Er 44 FILAMENTEssayer á nouveau. Contacter revendeur.

Er 45 ENTEREEProbléme clavier ou déclencheur pendant initialisation.

Er 45 ENTEREEEssayer à nouveau. N’appuyer sur aucune touche.

Er 46 EN PRETFin de période de test. Déclenchement bloqué.

Er 46 EN PRETcontacteur revendeur.




3.4 Error messager, German


Ch 1 KASSETTEPanoramakassette fehlt oder ist nicht gewechselt.

Ch 1 KASSETTEPrüfen der Kassette. Kassette wechseln.

Ch 2 CASSETTEFernröngenkassette fehlt oder ist nicht gewechselt.

Ch 2 CASSETTEPrüfen der Kassette. Kassette wechseln.

Ch 3 TUBUSTubus ist nicht in Panoramaposition.

Ch 3 TUBUSTubus prüfen.

Ch 4 TUBUSTubus ist nicht in Fernröntgenposition.

Ch 4 TUBUSTubus prüfen.

Ch 5 ***SPANNUNGNetzspannung ist außerhalb des gültigen Bereiches.

Ch 5 *** TENSIONMit neuem Film wiederholen.

Ch 6 POSITIONOP100 ist nicht in Start-position.

Ch 6 POSITIONPanorama Tubus prüfen. QA & ceph: Position-Ch 6 POSITIONTaste drücken um Strahler einzustellen.

Ch 7 *** SCHALTERAuslöseschalter zu schnell losgelassen.

Ch 7 ***SCHALTERMit neuem Film wiederholen.

Ch 8 INSPEKTION2000 Belichtungen seit der letzten Inspektion.

Ch 8 INSPEKTIONKundendienst verstän digen.

Sy 20 *** WARTENBelichten ist zur Zeit nicht möglich.

Sy 20 *** WARTENBitte warten. Beachten Sie die Zeit auf der Anzeige..

Sy 21 WARMStrahler zu warm. Belichten ist zur Zeit nicht möglich.

Sy 21 WARMBitte warten, bis OP100 “READY” anzeigt.

Sy 22 ***GENERATORAusfall des Generators während der Belichtung.

Sy 22 ***GENERATOR Erneutes Laden der Kassette. Neuer Versuch.

Sy 23 INVERTERRöhrestrom & Spannung steigen während der Belichtung nicht an.

Sy 23 INVERTERErneutes Laden der Kassette. Neuer Versuch.

Sy 24 FILAMENTRöhrenstom steigt während der Belichtung nicht an.

Sy 24 FILAMENTKassette laden, auslösen.

Sy 25 AECGrundfrequenz ist falsch. Kundendienst benachrichtigen.

Sy 25 AECIm manuellen Belichtungsmodus weiterarbeiten.

Sy 26 EEPROMScreiben in der Speicher nicht möglich.

Sy 26 EEPROMNeuer Versuch. Kundendienst benachrichtigen.



Sy 27 DREHBEWEGUNGproblem mit der Drehbewegung.

Sy 27 DREHBEWEGUNGNeuer Versuch. Kundendienst benachrichtigen.

Sy 28 KASSETTEProblem mit der Kassettenbewegung.

Sy 28 KASSETTENeuer Versuch. Kundendienst benachrichtigen.

Sy 29 LINEARProblem mit der Geradenbewegung.

Sy 29 LINEARNeuer Versuch. Kundendienst benachrichtigen.

Sy 30 HALTERProblem mit der Bewegung des Kassettenhalters.

Sy 30 HALTERNeuer Versuch. Kundendienst benachrichtigen.

Sy 31 VERTICALProblem mit der vertikalen Bewegung.

Sy 31 VERTICALNeuer Versuch. Kundendienst benachrichtigen.

Er 40 CPUAusfall der CPU.

Er 40 CPUNeuer Versuch. Kundendienst benachrichtigen.

Er 41 CPUAusfall der RAM-Kontrolle.


Er 42 CPUAusfall der EPROM-Kontrolle beim Anschalten.


Er 43 *** SPANNUNGProblem an dem Power Board oder an der Heiz Platine.

Er 43 *** SPANNUNGNICHT ANSCHALTEN!Kundendienst benachrichtigen.

Er 44 FILAMENTVorheizungskreis funktioniert nicht.

Er 44 FILAMENTNeuer Versuch. Kundendienst benachrichtigen.

Er 45 TASTEAuslösetaste gedrückt während des Anschaltens.

Er 45 TASTENeuer Versuch. Drüken Sie keine Taste.

Er 46 BEZAHLENEnde der Testphase. Belichtung nicht möglich.

Er 46 BEZAHLENBenachrichtigen Sie Ihren Händler.




3.5 Error messages, Spanish

1st SCREEN12345678901234567890

2nd (3rd) SCREEN12345678901234567890

Vf 1 CASETECasete Panorámico inexistente o mal colocado.

Vf 1 CASETECompruebe el casete. Vuelva a colocario.

Vf 2 CASETE Casete Cefalostato inexistente o mal colocado.

Vf 2 CASETECompruebe el casete. Vuelva a colocario.

Vf 3 COLIMADORColimador e posición no panorámica.

Vf 3 COLIMADORCompruebe posición del colimador.

Vf 4 COLIMADORColimador en posición no Cefalostato.

Vf 4 COLIMADORCompruebe posición del colimador.

Vf 5 *** VOLTAJE Tension de red incorrecta.Problema Temporal?

Vf 5 *** VOLTAJEReintene con pelicula nueva.

Vf 6 POSICIONOP100 en posicion no inicial.

Vf 6 POSICIONPan: Averia compruebe posicion colimador. Vf 6 POSICION

QA & cef: Pulsar tecla posicioninicial.

Vf 7 *** EXPOSICIONInterruptor soltado antes de tiempo.

Vf 7 *** EXPOSICIONReintente con pelicula nueva.

Vf 8 MANTENIMIENTO 2000 disparos desde última revisión.

Vf 8 MANTENIMIENTOLlame a su distribuidor. Reanude operación.

Sg 20 *** ESPEREEspere un momento antes de disparar.

Sg 20 *** ESPEREPor favor espere inicializacion.

Sg 21 CALIENTETubo caliente. Espere un momento antes de disparar.

Sg 21 CALIENTEPor favor espere OP100 “LISTO”.

Sg 22 ***GENERADORError del generador durante el ciclo de disparo.

Sg 22 ***GENERADOR Cargue casete de nuevo. Reintente.

Sg 23 INVERSORFalta de corriente y voltaje en el tubo al disparar.

Sg 23 INVERSORCargue casete de nuevo. Reintente.

Sg 24 FILAMENTOFalta de corriente en el tubo al disparar.

Sg 24 FILAMENTOCargue casete de nuevo. Reintente. Llame al técnico.

Sg 25 AECFrecuencia de base AEC incorrecta. Llame al técnico.

Sg 25 AECNOTA: El OP100 puede usarse en modo manual.

Sg 26 EEPROMFallo en la memoria.

Sg 26 EEPROMReintente. Llame al técnico.

Sg 27 ROTACIÓNProblema del movimiento de rotación.

Sg 27 ROTACIÓNReintente. Llame al técnico.



Sg 28 CASETE Problema del movimiento de casete.

Sg 28 CASETEReintente. Llame al técnico.

Sg 29 LINEAL Problema del movimiento de lineal.

Sg 29 LINEALReintente. Llame al técnico.

Sg 30 PORTA-CASETEProblema del movimiento del porta casete.

Sg 30 PORTA-CASETEReintente. Llame al técnico.

Sg 31 ARRIBA/ABAJOProblema del movimiento vertical.

Sg 31 ARRIBA/ABAJOReintente. Llame al técnico.

Er 40 CPUFallo de proceso del CPU.

Er 40 CPUReintente. Llame al técnico.

Er 41 CPUFallo de la comprobación de RAM CPU.


Er 42 CPUFallo de la comprobación de EPROM al conectar.


Er 43 *** VOLTAJEProblema de tarjeta de Potencia o Filamento.

Er 43 *** VOLTAJENO UTILIZAR EL OP100! Llame al servicio técnico.

Er 44 FILAMENTOError precalentamiento del tubo.

Er 44 FILAMENTOReintente. Llame al técnico.

Er 45 CONEXIONProblema de pulsador o de teclado durante la puesta en tensión.

Er 45 CONEXIONReintente. No toque ninguna tecla.

Er 46 PAGOFin del periodo de prueba. Bloqueo de disparo.

Er 46 PAGOLlame a su distribuidor.

1st SCREEN12345678901234567890

2nd (3rd) SCREEN12345678901234567890



3.6 Error messages, Italian

1st SCREEN 12345678901234567890

2nd (3rd) SCREEN 12345678901234567890

Ch 1 CASSETTACassetta della panoramica non in sede.

Ch 1 CASSETTAControllare posizione.

Ch 2 CASSETTACassetta craniostato non in sede.

Ch 2 CASSETTAControllare posizione.

Ch 3 DIAFRAMMADiaframma non posizionato in panoramica.

Ch 3 DIAFRAMMAControllare posizione.

Ch 4 DIAFRAMMADiaframma non posizionato inteleradiografia.

Ch 4 DIAFRAMMAControllare posizione.

Ch 5 *** TENSIONEAlimentazione inferioere al minimo.

Ch 5 *** TENSIONEControllare e/o riprovare.

Ch 6 POSIZIONAMENTOOP100 non in posizione di partenza.

Ch 6 POSIZIONAMENTO Pan: Controllare posizione diaframma.

Ch 6 POSIZIONAMENTOQA & ceph: Premere il tasto di allineamento THA.

Ch 7 ***ESPOSIZIONETasto esposizione rilasciato prima del tempo.

Ch 7 ***ESPOSIZIONERepartire con una nuova lastra.

Ch 8 PSE SERVICE2000 lastre eseguite senza nessun controllo.

Ch 8 PSE SERVICEContattare il servizio tecnico.

Sy 20 *** ATTENDEREEspozione non possible al momento.

Sy 20 *** ATTENDEREAttendere il tempo che compare sul display.

Sy 21 CALDOGeneratore surriscaldato.

Sy 21 CALDOAttendere fino all’apparizione di PRONTO.

Sy 22 ***GENERATOREGuasto del generatore.

Sy 22 ***GENERATORERiazzerare, rimuovere la cassetta e riprovare

Sy 23 CORRENTETensione, o corrente insufficiente.

Sy 23 CORRENTERiazzerare e riprovare dopo qualche istante.

Sy 24 FILAMENTOAssorbimento di corrente insufficente.

Sy 24 FILAMENTO Riazzerare,riprovare e/o chiamare il tecnico.

Sy 25 AECSistema automatico di esposizione OUT.

Sy 25 AECUtilizzare in modo manulale.

Sy 26 EEPROMMemorie scritture guasta.

Sy 26 EEPROMRiazzerare, riprovare e/o chiamare il tecnico.



Sy 27 ROTAZIONEProblema al sistema di rotazione.

Sy 27 ROTAZIONE Riazzerare,riprovare e/o chiamare il tecnico.

Sy 28 CASSETTEProblema al sistema di movomento cassetta.

Sy 28 CASSETTE Riazzerare,riprovare e/o chiamare il tecnico.

Sy 29 ALLINEAMENTOProblema al sistema di allineamento.

Sy 29 LINEARRiazzerare, riprovare e/o chiamare il tecnico.

Sy 30 SUPPORTOProblema al supporto cassetta.

Sy 30 HOLDERRiazzerare, riprovare e/o chiamare il tecnico.

Sy 31 ALTO/BASSProblema al movimento verticale.

Sy 31 UP/DOWNRiazzerare riprovare e/o chiamare il tecnico.

Er 40 CPUMicroprocessore in tilt.

Er 40 CPURiazzerare,riprovare e/o chiamare il tecnico.

Er 41 CPUMemoria RAM in tilt.

Er 41 CPURiazzerare,riprovare e/o chiamare il tecnico.

Er 42 CPUEprom difettosa alla massima potenza.

Er 42 CPURiazzerare, riprovare e/o chiamare il tecnico.

Er 43 *** TENSIONEPotenza Kv o asorbimento filamento difettosi.

Er 43 *** TENSIONENON UTILIZZARRE e chiamare subito il tecnico.

Er 44 FILAMENTOSistema di preriscaldamento non operativo.

Er 44 FILAMENTORiazzerare, riprovare e/o chiamare il tecnico.

Er 45 INPUTImpostazione dati errata.

Er 45 INPUT Riazzerare, riprovare e/o chiamare il tecnico.

Er 46 PAGAREFine del periode di prova con numero di espozioni limitato.

Er 46 PAGAREChiamare il rivenditore.

1st SCREEN 12345678901234567890

2nd (3rd) SCREEN 12345678901234567890



3.7 Error messages, Finnish

1. NÄYTTÖ 2. (3.) NÄYTTÖ

Ch 1 KASETTIPan.kasetti puuttuu tai ei vaihdettu kuvauksen jälkeen.

Ch 1 KASETTITarkista kasetti. Vaihda kasetti.

Ch 2 KASETTIKefalokasetti puuttuu tai ei vaihdettu kuvauksen jälkeen.

Ch 2 KASETTITarkista kasetti. Vaihda kasetti.

Ch 3 KAIHDINPrimaarikaihdin ei ole panoraamaku vausasennossa.

Ch 3 KAIHDINTarkista kaihtimen asento.

Ch 4 KAIHDINPrimaarikaihdin ei ole kefalokuvausasennossa.

Ch 4 KAIHDIN Tarkista kaihtimen asento.

Ch 5 *** JÄNNITEVerkkojännite liian alhainen tai korkea. Tilapäinen vika?

Ch 5 *** JÄNNITEUusi kuvaus uudelle filmille.

Ch 6 ASEMOINTIOP100 ei ole kuvauksen alkutilassa.

Ch 6 ASEMOINTI Panoraamakuvaus: Tarkista kaihtimen paikka.

Ch 6 ASEMOINTIQA & kefalokuvaus: Paina “Liike”-painiketta.

Ch 7 *** EXPONOINTIPainike päästetty kesken exponoinnin.

Ch 7 *** EXPONOINTIUusi kuvaus uudelle filmille.

Ch 8 HUOLTOMääräaikaishuolto? OP100:lla yli 2000 exponointia.

Ch 8 HUOLTOSoita OP100 myyjälle. Laite toimii normaalisti.

Sy 20 *** ODOTA:Exponointi tilapäisesti estetty.

Sy 20 *** ODOTAOdota hetki. Odotusaika (s) näytössä.

Sy 21 ODOTA: Säteilijä lämmennyt.Exponointi tilapäisesti estetty.

Sy 21 ODOTA:Odota hetki kunnes OP100:n “READY” syttyy.

Sy 22 *** SÄTEILIJÄVirhe säteilijässä exponoinnin aikana.

Sy 22 *** SÄTEILIJÄLataa uusi filmi kasettiin. Yritä uudestaan.

Sy 23 SÄTEILIJÄPutkivirta ja -jännite eivät nouse exponoinnin aikana.

Sy 23 INVERTERLataa uusi filmi kasettiin. Yritä uudestaan.

Sy 24 HEHKUVIRTAPutkivirta ei nouse exponoinnin aikana.

Sy 24 FILAMENTLataa uusi filmi. Yritä uudestaan. Soita huoltoon.

Sy 25 AUTOM.VALOTUS Valotusautomatiikan perustaajuus väärä. Soita huoltoon.

Sy 25 AUTOM.VALOTUSHUOM: OP100 toimii käsiarvoilla “M”.

Sy 26 EEPROM Muistiinkirjoitusvirhe.

Sy 26 EEPROMYritä uudestaan. Soita huoltoon.

Sy 27 PYÖRIJÄOngelma pyörijän liikkeissä.

Sy 27 PYÖRIJÄYritä uudestaan.Soita huoltoon.



Sy 28 KASETTIOngelma kasetin siirtoliikkeessä.

Sy 28 KASETTIYritä uudestaan.Soita huoltoon.

Sy 29 LINEAARIOngelma lineaari liikkeessä.

Sy 29 LINEAARIYritä uudestaan.Soita huoltoon.

Sy 30 KAS.TELINEOngelma kasettitelineen liikkeessä.

Sy 30 KAS.TELINEYritä uudestaan.Soita huoltoon.

Sy 31 VAUNUOngelma vaunun ylös/alas liikkeessä.

Sy 31 UP/DOWNYritä uudestaan.Soita huoltoon.

Er 40 CPUOngelma suorittimessa.

Er 40 CPUYritä uudestaan.Soita huoltoon.

Er 41 CPUSuorittimen RAM muistin tarkistusvirhe.


Er 42 CPUSuorittimen EPROM muistin tarkistusvirhe.


Er 43 *** JÄNNITEOngelma Power ja/tai Filament piirikortilla.

Er 43 *** JÄNNITEÄLÄ KÄYTÄ OP100:A! Soita huoltoon.

Er 44 HEHKUOngelma säteilijän esihehkussa.

Er 44 FILAMENTYritä uudestaan. Soita huoltoon.

Er 45 PAINIKE:Painiketta (ei “OK”) painettu sähköjä kytkettäessä.

Er 45 PAINIKEYritä uudestaan. Älä paina painikkeita.

Er 46 MAKSATestausjakso päättynyt. Exponointi estetty.

Er 46 MAKSASoita OP100 edustajalle.

1. NÄYTTÖ 2. (3.) NÄYTTÖ



3.8 Error messages, Swedish

1. rutan 2. (3.) rutan

Ch 1 CASSETTEPanoramakassett EJ i läge eller kassetten saknas.

Ch 1 CASSETTEKontrollera kassetten. Sätt in en kassett.

Ch 2 CASSETTEKefalostatkassett EJ i läge. Kassett saknas.

Ch 2 CASSETTEKontrollera kassetten. Sätt in en kassett.

Ch 3 COLLIMATORBländare EJ i läge för panoramabild.

Ch 3 COLLIMATORKontrollera bländarens position.

Ch 4 COLLIMATORBländare EJ i läge för kefalostatbild.

Ch 4 COLLIMATORKontrollera bländarens position.

Ch 5 *** VOLTAGEHuvudspänning för låg eller för hög. Tillfälligt problem?

Ch 5 *** VOLTAGETa om bilden med ny film.

Ch 6 POSITIONOP100 EJ i position för Start.

Ch 6 POSITIONPanorama: Kontrollera bländarens position.

Ch 6 POSITIONQA & ceph: Tryck på knappen för Rotation så att rtg-huvudet kommer i läge.

Ch 7 *** EXPOSUREKnappen för exponering för tidigt släppt.

Ch 7 *** EXPOSURETa om bilden med ny film.

Ch 8 PSE SERVICE2000 exponeringar sedan senaste förebyggande service

Ch 8 PSE SERVICEKontakta leverantören. Återgå till normal OP100 användning.

Sy 20 *** WAITExponering EJ möjligt för tillfället.

Sy 20 *** WAITVänta. Väntetid på teckenskärmen.

Sy 21 HOTRtg-rör varmt. Exponering EJ möjlig för tillfället.

Sy 21 HOTVänta på “READY”.

Sy 22 ***GENERATORGeneratorfel under exponeringen.

Sy 22 ***GENERATORLadda kassetten och prova igen.

Sy 23 INVERTERRörspänning och ström ej ökad under exponeringen.

Sy 23 INVERTERLadda kassetten och prova igen.

Sy 24 FILAMENTRörspänning ej ökad under exponeringen.

Sy 24 FILAMENTLadda kassetten och prova igen. Kontakta service.

Sy 25 AECAEC grundfrekvens felaktig. Kontakta servive.

Sy 25 AECOP100 kan användas men med manuell inställning av värden.

Sy 26 EEPROMMinnesfel.

Sy 26 EEPROMProva igen. Kontakta service.

Sy 27 ROTATIONRotationproblem.

Sy 27 ROTATIONProva igen. Kontakta service.

Sy 28 CASSETTEFel i kassettens rörelse.

Sy 28 CASSETTE Prova igen. Kontakta service.



Sy 29 LINEARFel i rörelse in mot pelare.

Sy 29 LINEARProva igen. Kontakta service.

Sy 30 HOLDERFel i kassetthållarens rörelse.

Sy 30 HOLDERProva igen. Kontakta service.

Sy 31 UP/DOWNFel i rörelse upp/ner.

Sy 31 UP/DOWNProva igen. Kontakta service.

Er 40 CPU Fel på kretskortet.

Er 40 CPUProva igen. Kontakta service.

Er 41 CPUFel på kretskortet. (RAM fel).

Er 41 CPUProva igen. Kontakta service.

Er 42 CPUEPROM fel vid upstart.

Er 42 CPUProva igen.Kontakta service.

Er 43 *** VOLTAGEFel i kretskort för inkommande spänning och ström.

Er 43 *** VOLTAGEANVÄND INTE OP100 ! Kontakta service.

Er 44 FILAMENTKrets för uppvärmning av rtg-rör ur funktion.

Er 44 FILAMENTProva igen. Kontakta service.

Er 45 INPUTKnapp på manöver panel eller expon. knapp intryckt vid uppstart.

Er 45 INPUTStäng av och starta om. Kontrollera att ingen knapp är intryckt.

Er 46 PAYSlut på testperiod. Exponering ej möjlig.

Er 46 PAYKontakta leverantören.

1. rutan 2. (3.) rutan




4 Technical specifications


Manufacturer: Instrumentarium Corp., Imaging DivisionP.O.Box 20 FIN-04301Tuusula, FINLAND

Manufacturer’s Quality System:

ISO 9001

Type: Ortho ID

Compliance: European models CE marked according to the Medical Device Directive 93/42/EEC.

Operating voltage: 25 V DC, from OP100

Interface: Serial

Film printing: Panoramic and cephalostat films with window type cassettes, printing after the exposure, adjustable printing contrast.

Print time (s): 0.1, 0.12, 0.16, 0.2, 0.32, 0.4, 0.5, 0.64, 0.8, 1.0, 1.2, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0, 6.4

Display: LCD, 4 rows x 20 characters, adjustable contrast

Keyboard: Alphanumeric with special characters

Patient data file: 100 pre-entered patients, 1 printed patient for multiple x-rays

Dialogue languages: English, German, French, Spanish & Italian(ROM A) English, Finnish & Swedish (ROM B)

Date format: YYMMDD, MMDDYY, DDMMYYYY/MM/DD, MM/DD/YY, DD/MM/YY

Date and time setting:

YY, MM, DD, hh, mm, ss

Clinic data: 10 dentist names, each max. 13 characters

Error code display: OP100 error codes with explanations and remedies

Size (W x D x H): 350 mm x 195 mm x 230 mm

Gross Weight: Gross ca. 7 kg




5 Appendix, dialogue table


Language Dialogue

12345678901234567890

All OP100All ORTHO ID V 1.01A All ORTHO ID V 1.01BAll ORTHOPANTOMOGRAPHAll 1: ↓ ↑ 2: OKAll 1: ← → 2: OK

Language Dialogue

English SELECT AND PRESS OK ↑ ↓German WÄHLEN & OK DR CKEN ↑ ↓French SELECTION ET OK ↑ ↓Spanish SELECTAR Y PULSAR OK ↑ ↓ Italian SELEZIONA E PREMI OK ↑ ↓Finnish VALITSE JA PAINA OK ↑ ↓Swedish VÄLJ OCH TRYCK OK ↑ ↓English PATIENT HISTORY ↑ ↓ German PATIENT HISTORY ↑ ↓French PATIENT HISTORY ↑ ↓Spanish PATIENT HISTORY ↑ ↓Italian PATIENT HISTORY ↑ ↓Finnish POTILASHISTORIA ↑ ↓Swedish PATIENTHISTORIA ↑ ↓

English 1. Select patient2. Add new patient3. Select clinic/Dr

German 1. Patient wählen2. Neuer Patient3. Klinik / Arzt

French 1. Selection Patient 2. Ajout Patient3. Selection Cabinet

Spanish 1. Selectar Paciente2. Marcar Paciente 3. Clinica / Doktor

Italian 1.Seleziona Paziente2. Aggiungi Paziente3.Seleziona Clin./Dr

Finnish 1. Valitse potilas2. Lisää potilastieto



3. Valitse hml/asemaSwedish 1. Välj patient

2. Skriv in patient3. Välj klinik/läkare



Language Dialogue

English 1: SELECT ↑ ↓ / A..Z1: SELECT ↑ ↓ / 1..102: PRESS OK

German 1: WAHL ↑ ↓ / A..Z1: WAHL ↑ ↓ / 1..102: OK DRüCKEN

French 1: CHOIX ↑ ↓ / A..Z 1: CHOIX ↑ ↓ / 1..102: PRESSER OK

Spanish 1: SELECTAR ↑ ↓ /A..Z1: SELECTAR ↑ ↓ /1..101: SELECTAR ↑ ↓ /1..102: PULSAR OK

Italian 1:SELEZIONA ↑ ↓ /A..Z1:SELEZIONA ↑ ↓ /1..102: PREMI OK

Finnish 1: VALITSE ↑ ↓ / A..Z1: VALITSE ↑ ↓ / 1.102: PAINA OKSwedish 1: VÄLJ ↑ ↓ / A..Z1: VÄLJ ↑ ↓ / 1..102: TRYCK PÅ OK

English NO PRE-ENTERED PATIENTSPRESS OK

German KEINEPATIENTENDATENOK DRüCKEN

French NONPRE-PROGRAMMEPATIENTSPRESSER OK

Spanish PACIENTENO LOCALIZADONO INFORMACIONPULSAR OK

Italian NO PAZIENTIPRE-INSERITI



PREMI OK

Finnish POTILASTIETOJAEI OLE MUISTISSAPAINA OK

Swedish PATIENTUPGIFTFINNS EJLAGRATTRYCK PÅ OK



Language Dialogue

English DELETING ENTRY CONFIRM WITH OK

German MIT OK BESTÄTIGEN

French SUPPRIMER SELECTIONCONFIRMER PAR OK

Spanish BORRAR INFORMACIONCONFIRMAR OK

Italian CANCELLAZIONE INSERIMENTO,CONFERMA OK

Finnish TIEDOT POISTETAANVAHVISTA JA PAINA OK

Swedish RADERA INFORMATIONTRYCK PÅ OK

English DELETINGDATA FILE

German DATEN FILELÖSCHEN

French SUPPRIMERDONNEÉS FICHIER

Spanish BORRARARCHIVO

Italian CANCELLAZIONE ARCHIVIO DATO

Finnish POTILAAN TIEDOTPOISTETAAN

Swedish RADERA PATIENTENS INFORMATION

English 1: ENTER DATA2: STORE WITH “OK”

German 1: DATEN EINGEBEN2: MIT OK SPEICHERN

French 1: ENTRER DONNEES2:ENREGISTRER PAR OK

Spanish 1: INTRODUCIR DATOS2: ALMACENTAR CON OK

Italian 1: INSERIRE DATO2:OK PER MEMORIZZARE

Finnish 1: SYÖTÄ TIEDOT2: TALLETA, PAINA OK

Swedish 1: SKRIV 2: LAGRA,TRYCK PÅ OK



English DATA STORED

German DATEN GESPEICHERT

French DONNEES ENREGISTREES

Spanish DATOS ALMACENADOS

Italian MEMORIA DATI

Finnish TIEDOT TALLENNETTU

Swedish INFORMATION LAGRAD

English DATA FILE FULL

German DATEN FILEVOLL

French DONNEÉS FICHEMEMOIRE PLEINE

Spanish ARCHIVOCOMPLETO

Italian ARCHIVIO DATIPIENO

Finnish TIEDOSTOON TÄYNNÄ

Swedish REGISTERFULL

English LANGUAGE VERSION

German SPRACHE

French CHOIX DE LA LANGUE

Spanish VERSIÓN DE IDIOMA

Italian LINGUA ITALIANO

Finnish KIELIVERSIO

Swedish SPRÅK VERSION



English ENGLISH

German DEUTSCH

French VERSION FRANCAISE

Spanish ESPAÑOL

Italian ITALIANO

Finnish SUOMI

Swedish SVENSKA

English 1: SET 2: OK

German 1: EINGABE 2: OK

French 1: MODIFIER 2: OK

Spanish 1: CAMBIAR 2: OK

Italian 1: SELEZIONARE 2: OK

Finnish 1: KIRJOITA 2: OK

Swedish 1: SET 2: OK

Language Dialogue

English SET DATE / TIME

German DATUM / ZEIT

French CHANGER DATE/HEURE

Spanish CAMBIO DE FECHA/HORA

Italian SELEZIONE DATA E ORA

Finnish ASETA PVM / AIKA

Swedish STÄLL DATUM / TID



Language Dialogue

English DATE FORMAT

German DATUMSFORMAT

French FORMAT DATE

Spanish FORMATO FECHA

Italian SELEZIONE FORMATO

Finnish PÄIVÄYKSEN MUOTO

Swedish FORMAT FÖR DATUM

Language Dialogue

English DDMMYY

German TTMMJJ

French JJMMAA

Spanish DDMMAA

Italian DDMMYY

Finnish PVKKVV

Swedish DDMMÅÅ

English MMDDYY

German MMTTJJ

French MMTTJJ

Spanish MMDDAA

Italian MMDDAA

Finnish KKPVVV

Swedish MMDDÅÅ



English YYMMDD

German JJMMTT

French AAMMJJ

Spanish AAMMDD

Italian YYMMDD

Finnish VVKKPV

Swedish ÅÅMMDD

English MM/DD/YY

German MM/TT/JJ

French MM/JJ/AA

Spanish MM/DD/AA

Italian MM/DD/YY

Finnish KK/PV/VV

Swedish MM/DD/ÅÅ

English CLINIC DATA

German PRAXIS / KLINIK

French DONNEES DU CABINET

Spanish DATOS DE LA CLINICA

Italian DATA CLINICA

Finnish ASIAKASTIEDOT

Swedish KLINIKDATA



English CLINIC/DENTIST NAME

German ARZTNAME

French NOM CABINET/DENTISTE

Spanish DATOS DEL DENTISTA

Italian NOME DEL DENTISTA

Finnish KLINIKKA/YKSI HML

Swedish KLINIK / TANDLÄKARE

English DENTIST #

German ARZT Nr.

French DENTISTE N

Spanish DENTISTA NO

Italian NOME DEL MEDICO

Finnish HAMMASLÄÄKÄRI NRO

Swedish TANDLÄKARE NR

Language Dialogue

English SET PRINT TIME

German BELICHTUNGSZEIT

French TEMPS D’IMPRESSION

Spanish HORA DE IMPRESION

Italian SELEZ. TEMPO STAMPA

Finnish ASETA VALOTUSAIKA

Swedish VÄLJA MÄRKNINGSTIDEN



English PRINTINGFOR

German DRUCKEN

French IMPRESSION

Spanish IMPRIMIENAO

Italian STAMPAPER

Finnish KIRJOITTAA...

Swedish MÄRKNING ...

English READYFOR

German FERTIG

French PRET

Spanish LISTO

Italian PRONTOPER

Finnish VALMIS

Swedish MÄRKNING KLAR




6 Spare parts

6 Spare parts There are two Ortho ID models, first ones up to s/n 1999, and CE modelsfrom s/n 2000. Note that parts #15, #33 and #34 are not interchangeablebetween these two models.

Pos Code Description Note

1 65735 Back cover 2 65734 Top cover 3 65730 Bumber 4 60154 Ortho ID Keyboard5 60161 Screen6 65725 Optics chassis 7 65736 Mirror #1 8 30303 Mirror #2 9 65732 Mirror holder10 65740 Mirror holder axle11 65726 Lens holder12 65727 Lens fastener 13 21710 Lens14 21566 Spring 0.5 x 5 x 1015 65723 Printing chassis 15 65782 Printing chassis CE16 65729 Latch 17 65728 Claw 18 21726 Spring 0.4 x 3 x 1519 21725 Spring 0.4 x 3 x 520 21737 Bushing M421 21720 Magnet 25 x 11 x 622 65720 Cassette holder chassis 23 21713 Magnet 40 x 25 x 1024 65722 Bearing support25 65721 Holder bracket 26 7909 Bearing27 65724 Chassis28 65731 Sliding rod29 21767 Spring 1.4x12x29030 21739 Pad 31 5483 Pad 32 65733 Scattered light shield 33 60155 Ortho ID CPU Board 33 60174 Ortho ID CPU Board CE33a 60157 Language ROM A33b 60156 Language ROM B33c 21714 Battery RAM34 69003 OP100 Interface cable34 69022 OP100 Interface cable CE


6 Spare parts

Option 65747 Mounting set for OP100 column (see below)

35 32512 Main label 36 3886 Star lock 37 1616 Cotter 3 x 2838 5403 Cotter 4 x 3239 21330 Screw M2.5 x 14 40 5732 Nut M 2.541 5731 Washer 2.7A42 21781 Screw M3 x 1643 4338 Screw M3 x 644 4259 Screw M3 x 1245 21480 Allen screw M3 x 12 46 331 Washer 3.2A47 21676 Screw M4 x 548 2747 Screw M4 x 650 5242 Screw M4 x 1051 4422 Screw M4 x 1254 3046 Screw 4 x 1657 4291 Washer 4.3B59 4683 Screw M5 x 1260 326 Nut M562 333 Washer 5.3B63 3588 Locking ring 4.364 4274 Nut M365 4292 Washer 3.2A66 6202 Screw M4 x 2567 6631 Washer 3.3A Nyloc 68 5044 Adjust ring 4 x 8 x 0.169 65738 Wall mount

Pos Code Description Note


6 Spare parts


6 Spare parts


7 Wiring diagrams

7 Wiring diagramsThe following documents are enclosed for the service reference:

• OP100 Wiring Diagram for Ortho ID• CPU Board schematics and layouts (60155)• CPU Board CE schematics and layouts (60174)• OP100 Interface cable (69003)• OP100 Interface cable CE (69022)• Cable 68999 (for X 12 - X 106)• OP100 Configuration Form for software version 1.2.01 • OP100 Configuration Form for software version 1.2.05 or higher


7 Wiring diagrams


Distributor:Instrumentarium Imaging is constantly improving its products and reserves the right to change these specifications without notice.

6330

1 0

3/20

03

© I

nstr

umen

tari

um I

mag

ing

www.InstrumentariumImaging.com

Instrumentarium ImagingP.O.Box 20, FIN-04301 Tuusula, FinlandTel. +358 10 394 6500 · Fax +358 10 394 [email protected]

Instrumentarium Imaging Inc.300 West Edgerton Avenue, MilwaukeeWisconsin 53207, USATel. +1 800 558 6120, +1 414 747 1030Fax +1 414 481 [email protected]

Instrumentarium Imaging France S.A.R.L.4, Avenue des Roses94386 Bonneuil Sur Marne Cedex, FranceTel. +33 1 43 39 51 51 · Fax +33 1 43 39 75 [email protected]

Instrumentarium Imaging Italia S.R.L.Via Cassanese, 10020090 Segrate (MI), ItalyTel. +39 02 21 30 28 1 · Fax +39 02 21 30 28 [email protected]

Instrumentarium Imaging Singapore152 Beach Road#12-03A Gateway East189721 SingaporeTel. +65 6391 8600 · Fax +65 6396 [email protected]

Instrumentarium Imaging Dental GmbHP.O.Box 2044, 77680 Kehl am Rhein, GermanyTel. +49 7851 932 90 · Fax +49 7851 932 [email protected]

Documents

63301 OP100 OC100 OrthoID Technical Manual 4AB