599852 VCI Update Instructions

7/21/2019 599852 VCI Update Instructions

http://slidepdf.com/reader/full/599852-vci-update-instructions 1/37

Jaguar Land Rover

Approved J2534 VCIUpdate Instructions

1

V10VCI Update Instructions



Intentionally Blank

2




Introduction.....................................................................................................4Introduction...................................................................................................................4 Acronyms......................................................................................................................4

VCI Device Installation Level Information....................................................5i-VIEW J2534 VCI Device Installation Details...............................................................5Diagnostic Associates (DA) J2534 VCI Device Installation Details..............................6Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details.........................7JLR J2534 VCI Device Installation Details...................................................................8

VCI Device Part Numbers and Vehicle Coverage Details...........................9VCI Device Part Numbers and Vehicle Coverage Details............................................9

Installation Level Verification and Update Processes - SDD Machines UsingWindows 7 OS...............................................................................................11

Introduction.................................................................................................................11

i-VIEW J2534 VCI Device...........................................................................................11DA J2534 VCI Device.................................................................................................15Drew Tech Mongoose Pro JLR J2534 VCI Device.....................................................20JLR J2534 VCI Device................................................................................................23

Installation Level Verification and Update Processes - SDD Machines UsingWindows XP OS............................................................................................25

Introduction.................................................................................................................25i-VIEW J2534 VCI Device...........................................................................................25DA J2534 VCI Device.................................................................................................29Drew Tech Mongoose Pro JLR J2534 VCI Device.....................................................34

JLR J2534 VCI Device................................................................................................36

3


VCI Update Instructions



Introduction

Introduction

This document will guide the user through the Verification and Updating processes for theinstallation software and firmware for all Jaguar Land Rover (JLR) approved J2534 VehicleCommunication Interface (VCI) devices.

Paper copies of this document are uncontrolled, always refer to the electronicsource material for the latest information. Always download the latest versionavailable on TOPIx in Diagnostics.

Making sure the Symptom Driven Diagnostics (SDD) machine is operating with the latestinstallation and firmware software for the VCI devices available in the workplace will help toreduce communication issues between the SDD machine and vehicles.

VCI device functionally will be affected, if the VCI device software and firmwarelevel is not updated when required in line with the SDD software level.

For each piece of software or firmware, there is a detailed Verification process accompaniedby an Updating process should it be required. To avoid repetition, the Updating processshould be read as a continuation of the Verification process.

Before any of the instructions detailed in this document are completed, always make surethe latest released version of the SDD software and associated software updates have beeninstalled.

The following information is clearly divided by the Operating System (OS) for the SDDmachine, as the Verification and Update processes differ between Windows 7 OS andWindows XP OS.

Note: When updating any VCI device, the SDD application must not be in operation.

Acronyms

DescriptionAcronym

Diagnostic AssociatesDA

Jaguar Land Rover JLR

Operating SystemOS

Symptom Driven DiagnosticsSDD

Vehicle Communication InterfaceVCI

4





VCI Device Installation Level Information

i-VIEW J2534 VCI Device Installation Details

NotesSDD Systems InformationSoftware Level

Information

Software Details

All SDD machines

using i-VIEW J2534

Vehicle

Communication

Interface (VCI)

devices must be

updated to this level

SPX T-200 1.2.7.0DLL Version1.4.9Software Driver Level

The i-VIEW J2534

VCI device only

needs to be updatedwhen required, as the

firmware is held on

the VCI device itself

6.0.0Firmware Version6.0.0Firmware Level

Installation Level Verification Actions

1. Verify the Software Driver Level is at the latest version

• If the software is not to the latest version, complete Updating Software Driver Level

2. Complete the process steps to update the Firmware Level to the latest version

3. With the Software Driver Level and Firmware Level to the latest versions, complete the

VCI Device to SDD Machine Recognition and Final Checks

Take me to Installation Level Verification and Update Processes: i-VIEW J2534 VCI Device:

• SDD Machines Using Windows 7 Operating Systems (OS)See page 11, i-VIEW J2534 VCI Device

• SDD Machines Using Windows XP OSSee page 25, i-VIEW J2534 VCI Device

5





Diagnostic Associates (DA) J2534 VCI Device Installation Details

NotesSDD Systems InformationVCI DeviceSoftware Level

Information

Software

Details

All SDD machines

using DA J2534

Vehicle

Communication

Interface (VCI)

devices must be

updated to this

level

2.63DLL Version All4.6Software Driver

Level

Not Applicable All2.4.8 App Hub Level

The DA J2534 VCI

Device only needs

to be updated

when required, as

the firmware is

held on the VCI

device itself

62.1Firmware VersionDA-Dongle62Firmware Level

62.2DAVINA2

62.3DA-ST512

62.4DAVINA3




2. Verify the DA App Hub Level is at the latest version

• If the software is not to the latest version, complete Updating DA App Hub Level

3. Verify the DA Firmware Level is at the latest version• If the firmware is not to the latest version, complete Updating DA Firmware Level

4. With the Software Driver Level, DA App Hub Level and DA Firmware Level to the latestversions, complete the VCI Device to SDD Machine Recognition and Final Checks

Take me to Installation Level Verification and Update Processes: DA J2534 VCI Device:

• SDD Machines Using Windows 7 Operating Systems (OS)See page 15, DA J2534 VCI Device

• SDD Machines Using Windows XP OS

See page 29, DA J2534 VCI Device

6





Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details


Information

Software Details

All SDD machines

using MongoosePro

JLR Vehicle

Communication

Interface (VCI)

devices must be


v1.1.16.0DLL Version1.01.16.00Software Driver

Level

FW.1.1.16.0Firmware Version1.01.16.00Firmware Level




2. With the Software Driver Level to the latest version, complete the VCI Device to SDDMachine Recognition and Final Checks

Take me to Installation Level Verification and Update Processes: Drew Tech Mongoose ProJLR J2534 VCI Device:

• SDD Machines Using Windows 7 Operating Systems (OS)See page 20, Drew Tech Mongoose Pro JLR J2534 VCI Device

• SDD Machines Using Windows XP OS

See page 34, Drew Tech Mongoose Pro JLR J2534 VCI Device

7





JLR J2534 VCI Device Installation Details


Information

Software Details

All SDD machines

using JLR Vehicle

Communication

Interface (VCI)

devices must be


1.06DLL Version1.0.6Software Driver

Level

1.5Firmware Version1.5Firmware Level




2. With the Software Driver Level to the latest version, complete the VCI Device to SDDMachine Recognition and Final Checks

Take me to Installation Level Verification and Update Processes: JLR VCI J2534 Device:

• SDD Machines Using Windows 7 Operating Systems (OS)See page 23, JLR J2534 VCI Device

• SDD Machines Using Windows XPSee page 36, JLR J2534 VCI Device

8





VCI Device Part Numbers and Vehicle Coverage Details

VCI Device Part Numbers and Vehicle Coverage Details

VCI Device Part Number Details

VCI

JLR VCIDA ST512DAVINADA Donglei-ViewDrewtech Mongoose

JLR-00001 New VCIDAPN0035DAPN0031DAPN0040IVIEWMONGOOSE-VCIBosch Part

Number

VCI Device Vehicle Coverage Table

VCIVehicle ModelBrand

JLR VCIDA ST512DAVINADA

Dongle

i-ViewDrewtech

Mongoose3333XXL316 - Defender Land Rover

XXXXXXL319 - Discovery 3

/ LR3 - Discovery 4

/ LR4

XXXXXXL320 - Range

Rover Sport

1111X1L322 - Range

Rover

XXXXXXL359 - Freelander 2

XXXXXXL405 - All NewRange Rover

XXXXXXL494 - Range

Rover Sport

XXXXXXL538 - Range

Rover Evoque

XXXXXXL550 - Discovery

Sport

222332X100 - XKJaguar

XXXXXXX150 - XK

XXXXXXX152 – F-TYPE

XXX33XX200 - S-TYPE

XXXXXXX250 - XF

222332X300 - XJ

XXX33XX350 - XJ

XXXXXXX351 - XJ

XXX33XX400 - X-TYPE

XXXXXXX760 - XE

9





Table Key

Vehicle line fully supportedX

Vehicle Line fully supported apart from viewing Datalogger signals from both PCM & TCCM

modules simultaneously on 06MY variants

1

Vehicle Line fully supported apart from flash programming of AJ26 & AJ27 PCMs. New modules

are supplied pre-programmed

2

Vehicle line partially supported3

10





Installation Level Verification and Update Processes - SDDMachines Using Windows 7 OS

Introduction

The verification and updating processes contained in the section should only be completedon SDD machines using the Windows 7 Operating System (OS).

For SDD machines using the Windows XP OS,See page 25, Introduction


i-VIEW J2534 VCI Device

For details regarding the latest installation software and firmware level for the VehicleCommunication Interface (VCI) device,See page 5, i-VIEW J2534 VCI Device Installation Details

Software Driver Level

Verifying Software Driver Level

1. Power up the SDD machine

2. Press the ‘Windows Key’

3. Select ‘Control Panel’

4. Select ‘Programs’

5. Select ‘Programs and Features’

Note: The ‘Programs and Features’ control panel displays a list of software on the SDDmachine

6. Locate ‘SPX i-VIEW J2534’ in the software listing latest

7. Select ‘SPX i-VIEW J2534’

8. Using the ‘Version’ column, confirm the current Software Driver Level information statedon screen and compare it to that identified in the installation details table,See page 5, i-VIEW J2534 VCI Device Installation Details

• If the Software Driver Level matches the required level, go to step 1 of: Updating

Firmware Level• If the Software Driver Level is not to the required level, complete the following steps

1 to 27 of: Updating Software Driver Level

Updating Software Driver Level

1. If connected, disconnect the VCI device from the SDD machine

2. Select the ‘Uninstall’ button

Note: This is displayed at the top of the software listing above ‘Name’

3. A ‘Programs and Features’ message pop up window will be displayed

4. Select ‘Yes’

11





5. A pop up window will be displayed and will close automatically

6. A pop up window will be displayed ‘SPX i-VIEW J2534’

7. A progress scroll bar will be displayed and will close automatically once completed

8. Close the ‘Programs and Features’ control panel

9. Restart the SDD Machine


11. Select ‘All Programs’

12. Select ‘JLR’

13. Select ‘SDD’

14. Select ‘VCI Device Drivers’

15. Select ‘SPX i-View’

16. A pop up window will be displayed - ‘Welcome to the SPX i-View J2534 setup wizard’,select ‘Next’

17. Select the box next to ‘I accept the terms in the License Agreement’, select ‘Next’

18. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Choose Setup Type’,select ‘Complete’

19. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Service Mode’

20. Make sure ‘User Mode’ is selected

21. Select ‘Next’

22. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Ready to install SPXi-VIEW J2534’

23. Select ‘Install’

24. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Service Mode – Completedthe SPX i-VIEW J2534 Setup Wizard’

25. Select ‘Finish’

26. Restart the SDD machine to complete the installation

27. Go to step 1 of: Updating Firmware Level

12





Firmware Level (File System Version)

Updating Firmware Level

1. Connect the VCI device to the SDD machine

2. Connect the VCI device to a vehicle



5. Select ‘SPX’

6. Select ‘i-VIEW’

7. Select ‘i-VIEW Device Manager’

8. Select the VCI device serial number

9. Select ‘Full Reload’ from the ‘i-VIEW Device Manager’ to update the VCI device

10. Select ‘Yes’ from the pop up message window to reload the device

11. Select ‘Close’ when the ‘Full Reload’ has completed

12. Close ‘i-VIEW Device Manager’

13. Go to step 1 of: i-VIEW J2534 VCI Device to SDD Machine Recognition and FinalChecks

13





i-VIEW J2534 VCI Device to SDD Machine Recognition and Final Checks

1. Disconnect the VCI device from the SDD machine

2. Disconnect the VCI device from the vehicle

3. Shut down the SDD machine

4. Connect the VCI device to SDD

5. Connect the VCI device to a vehicle


7. Start the SDD application

8. Login to SDD

9. Select ‘Continue’ from the displayed ‘Warning Page’

10. Select ‘Settings’ tab

11. Select ‘System Information’ tab12. Select ‘Details’ next to ‘Vehicle Communications Interface Status’

13. Click ‘Connected’ next to ‘SPX – i-VIEW’

14. Make sure the information stated on screen matches that identified in the installationdetails table,See page 5, i-VIEW J2534 VCI Device Installation Details

• DLL Version: SPX T-### #.#.#.#

• Firmware Version: #.#.#

15. If the software information is confirmed as being correct, select ‘Close’ and use SDD asnormal

16. If the software information is confirmed as being incorrect, restart the software updatingprocess, See Installation Level Verification Actions

14





DA J2534 VCI Device

For details regarding the latest installation software and firmware level for the VehicleCommunication Interface (VCI) device,

See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details








Note: The ‘Programs and Features’ control panel displays a list of software on the SDD

machine6. Locate ‘DA J2534 Software’ in the software listing

7. Select ‘DA J2534 Software’

8. Using the ‘Version’ column, confirm the current Software Driver Level information statedon screen and compare it to that identified in the installation details table,See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details

• If the Software Driver Level matches the required level, go to step 6 of: Verifying DAApp Hub Level

• If the Software Driver Level is not to the required level, complete the following steps







4. Select ‘Yes’

5. A pop up window will be displayed

6. Select ‘Yes’


8. A pop up window will be displayed ‘DA J2534 Software’







15







17. Select ‘DA Dongle and Davina’

Note: DA-ST512 uses the Davina driver

18. A pop up window will be displayed - ‘Welcome to the DA J2534 software setup wizard’ -select ‘Next’

19. A pop up window will be displayed - ‘Select Installation Folder’, select ‘Next’

20. A pop up window will be displayed - ‘Confirm Installation’, select ‘Next’


22. A pop up window will be displayed - ’Installation Complete’

23. Select ‘Close’


25. Go to step 1 of: Verifying DA App Hub Level

DA App Hub Level

Verifying DA App Hub Level





5. Select ‘Programs and Features’Note: The ‘Programs and Features’ control panel displays a list of software on the SDDmachine

6. Locate ‘DA App Hub’ in the software listing

7. Select ‘DA App Hub’

8. Using the ‘Version’ column, confirm the current DA App Hub Level information stated onscreen and compare it to that identified in the installation details table,See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details

• If the DA App Hub version matches the required level, go to step 1 of: Verifying DA

Firmware Level• If the DA App Hub version is not to the required level, complete the following steps 1to 31 of: Updating DA App Hub Level

Updating DA App Hub Level


2. Make sure the SDD machine is connected to an internet connection

3. Select ‘DA App Hub’ in the software listing



16





5. A pop up window will be displayed ‘DA App Hub’



8. Select ‘Yes’

Note: The DA App Hub has now been removed from the ‘Programs and Features’ control panel list





13. Select and open ‘Internet Explorer’

14. In the Internet Explorer address bar, enter the following:

• http://www.diagnostic-associates.com/pages/downloads

15. Select the appropriate Language ‘Download’ link at the bottom of the ‘DA App Hub Setup’section

16. A pop up window will be displayed - ‘File Download’, select ‘Save’

17. A pop up window will be displayed - ‘Save As’, select ‘Desktop’

18. Select ‘Save’ and save the latest ‘DAAppHub’ .zip file to the SDD Desktop

19. Once the Download has completed, select ‘Close’

20. Press the ‘Windows Key’ and the ‘D’ key at the same time

Note: This will now display the SDD desktop

21. Select and open the ‘DAAppHub’ .zip file saved to the SDD Desktop

22. Open ‘DAAppHubSetup’, select ‘Run’

23. A pop up window will be displayed - ‘Open File - Security Warning’, select ‘Run’

24. A pop up window will be displayed - ‘Welcome to DA App Hub Setup Wizard’, select‘Next’

25. A pop up window will be displayed - ‘Select Installation folder’, select ‘Everyone’ and thenselect ‘Next’


27. A pop up window will be displayed with a progress scroll bar and will close automaticallyonce completed

28. A pop up window will be displayed - ‘Installation Complete’, select ‘Close’

29. Close all open windows


31. Go to step 1 of: Verifying DA Firmware Level

17





DA Firmware Level

Verifying DA Firmware Level


Note: Make sure the VCI device is not connected to a vehicle




5. Select ‘Diagnostic Associates Ltd'


7. A ‘DA App Hub’ pop up window will be displayed

8. A message in the ‘Home’ window will identify if the DA Firmware Level requires updating

• If the DA Firmware Level is up to date, close all open windows and go to step 1 of: DAJ2534 VCI Device to SDD Machine Recognition and Final Checks

• If the DA Firmware Level needs updating, complete the following steps 1 to 6 of:Updating DA Firmware Level

Updating DA Firmware Level

1. Within the ‘DA App Hub’, select ‘Update Applications’

2. Select ‘Update Device’

3. Allow the software update process to complete

4. A pop up window will confirm the update has completed5. Close the pop up window

6. Go to step 1 of: DA J2534 VCI Device to SDD Machine Recognition and Final Checks

18





DA J2534 VCI Device to SDD Machine Recognition and Final Checks


2. Shut down the SDD Machine

3. Connect the VCI device to the vehicle

4. Connect the VCI device to the SDD machine using the USB cable



7. Login to SDD



10. Select ‘System Information’ tab

11. Select ‘Details’ next to ‘Vehicle Communications Interface Status’12. Select ‘Connected’ next to ‘DA-Dongle or DAVINA2

Note: DA-ST512 and DAVINA3 will be detailed as a DAVINA2

13. Make sure the information stated on screen matches that identified in the installationdetails table,See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details

• DA-Dongle or DAVINA2

• DLL Version: #.##

• Firmware Version: ##.#


15. If the software information is confirmed as being incorrect, restart the software updatingprocess, go to: Installation Level Verification Actions

19





Drew Tech Mongoose Pro JLR J2534 VCI Device

For details regarding the latest installation software level for the Vehicle CommunicationInterface (VCI) device,

See page 7, Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details









machine6. Locate ‘J2534 MongoosePro JLR’ in the software listing

7. Select ‘J2534 MongoosePro JLR’

8. Using the ‘Version’ column, confirm the current Software Driver Level information statedon screen and compare it to that identified in the installation details table,See page 7, Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details

Note: Make sure no other installs of MongoosePro JLR or Mongoose JLR are visible inthe software listing. Other installs could cause a software conflict and must be removed.Complete the following steps 1 to 29 of: Updating Software Driver Level

• If the Software Driver Level matches the required level, go to step 1 of: Drew TechMongoose Pro JLR J2534 VCI Device to SDD Machine Recognition and Final

Checks

• If the Software Driver Level is not to the required level, complete the following steps1 to 30 of: Updating Software Driver Level





Note: Uninstall MongoosePro JLR, MongoosePro Jaguar or Mongoose JLR if listed


4. Select ‘Yes’


6. A pop up window will be displayed 'The following applications should be closed beforecontinuing the install’ (ProtocolAccessServer)

7. Select ‘Automatically close applications and attempt to restart them after setup is complete’

8. Select ‘OK’


20












17. Select ‘DrewTech Mongoose’

18. A pop up window will be displayed - ‘Welcome to the MongoosePro JLR setup wizard’ -select ‘Next’

19. Select the box next to ‘I accept the terms in the License Agreement’


21. A pop up window will be displayed - select ‘Next’

22. A pop up window will be displayed - ‘Ready to Install J2534 MongoosePro JLR' - select‘Install’

23. A pop up window will be displayed - ‘Installing J2534 MongoosePro JLR' - select ‘Install’

24. A pop up window will be displayed with a progress scroll bar

25. A pop up window may be displayed - select ‘Install’

26. A pop up window will be displayed - ‘Please attach your device to the computer any timeafter the installation has finished’

Note: Do not connect the Mongoose Pro JLR device at this time

27. Select ‘OK’



30. Go to step 1 of: Drew Tech Mongoose Pro JLR J2534 VCI Device to SDD MachineRecognition and Final Checks

21





Drew Tech Mongoose Pro JLR J2534 VCI Device to SDD Machine Recognition andFinal Checks

1. Connect the VCI device to the vehicle

2. Connect the VCI device to the SDD machine with the USB cable



5. Login to SDD




9. Select ‘Details’ next to ‘Vehicle Communications Interface Status’

10. Select ‘Connected’ next to ‘MongooseProJLR’

11. Make sure the information stated on screen matches that identified in the installationdetails table,See page 7, Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details

• DLL Version: MongoosePro JLR J2534 Library V#.#.#.#

• Firmware Version: MongoosePro JLR FW:#.#.#.#



22





JLR J2534 VCI Device


See page 8, JLR J2534 VCI Device Installation Details









machine6. Locate ‘JLR VCI’ in the software listing

7. Select ‘JLR VCI’

8. Using the ‘Version’ column, confirm the current Software Driver Level information statedon screen and compare it to that identified in the installation details table,See page 8, JLR J2534 VCI Device Installation Details

• If the Software Driver Level matches the required level, go to step 1 of: JLR J2534VCI Device to SDD Machine Recognition and Final Checks

• If the Software Driver Level is not to the required level, complete the following steps







4. Select ‘Yes’

5. A pop up window will be displayed

6. Select ‘Yes’









23






16. A pop up window will be displayed - ‘Welcome to the JLR VCI setup wizard’ - select ‘Next’

17. A pop up window will be displayed - ‘Select Installation Folder’, select ‘Everyone’ andthen select ‘Next’






23. Go to step 1 of: JLR J2534 VCI Device to SDD Machine Recognition and Final Checks

JLR J2534 VCI Device to SDD Machine Recognition and Final Checks1. Connect the VCI device to the vehicle




5. Login to SDD





10. Select ‘Connected’ next to ‘JLR VCI’

11. Make sure the information stated on screen matches that identified in the installationdetails table,See page 8, JLR J2534 VCI Device Installation Details

• DLL Version: #.#.#

• Firmware Version: #.#



24





Installation Level Verification and Update Processes - SDDMachines Using Windows XP OS

Introduction

The verification and updating processes contained in the section should only be completedon SDD machines using the Windows XP Operating System (OS).

For SDD machines using the Windows 7 OS,See page 11, Introduction


i-VIEW J2534 VCI Device

For details regarding the latest installation software and firmware level for the VehicleCommunication Interface (VCI) device,See page 5, i-VIEW J2534 VCI Device Installation Details






4. Select ‘Add or Remove Programs’

Note: The ‘Add or Remove Programs’ control panel displays a list of software on theSDD machine

5. Locate ‘SPX i-VIEW J2534’ in the software listing

6. Select ‘SPX i-VIEW J2534’

7. Select on ‘Click here for support information’

Note: ‘Support Info’ will be displayed in a pop up window stating the Software VersionLevel

8. Using the ‘Support Info’, confirm the current Software Driver Level information stated onscreen and compare it to that identified in the installation details table,

See page 5, i-VIEW J2534 VCI Device Installation Details• If the Software Driver Level version matches the required level, go to step 1 of:


• If the Software Driver Level version is not to the required level, complete the followingsteps 1 to 28 of: Updating Software Driver Level



2. Close the ‘Support Info’ box

3. Select the ‘Remove’ button

25





4. An ‘Add or Remove Programs’ message box will be displayed

5. Select ‘Yes’


7. Close the ‘Add or Remove Programs’ control panel







14. Select ‘SPX i-View’

15. A pop up window will be displayed - ‘Welcome to the SPX i-View J2534 setup wizard’,select ‘Next’



18. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Choose Setup Type’,select ‘Complete’

19. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Service Mode’

Note: Make sure ‘User Mode’ is selected


21. A pop up window will be displayed - ‘SPX i-View J2534 Setup – Ready to install SPXi-VIEW J2534’



24. After the install a pop up window will be displayed - ‘SPX i-View J2534 Setup - Completedthe SPX i-VIEW J2534 Setup Wizard’




28. Go to step 1 of: Updating Firmware Level

26





Firmware Level (File System Version)


1. Connect the VCI to the SDD machine

2. Connect the VCI to a vehicle



5. Select ‘SPX’

6. Select ‘i-VIEW’

7. Select ‘i-VIEW Device Manager’

8. Select the VCI device serial number

9. Select ‘Full Reload’ from the ‘i-VIEW Device Manager’ to update the VCI device

10. Select ‘Yes’ from the pop up message window to reload the device

11. Select ‘Close’ when the ‘Full Reload’ has completed

12. Close ‘i-VIEW Device Manager’

13. Go to step 1 of: i-VIEW J2534 VCI Device to SDD Machine Recognition and FinalChecks

27





i-VIEW J2534 VCI to SDD Device Recognition and Final Checks

1. Disconnect the VCI from the SDD machine

2. Disconnect the VCI from the vehicle


4. Connect the VCI to a vehicle

5. Connect the VCI to SDD



8. Login to SDD



11. Select ‘System Information’ tab12. Select ‘Details’ next to ‘Vehicle Communications Interface Status’

13. Click ‘Connected’ next to ‘SPX – i-VIEW’

14. Make sure the information stated on screen matches that identified in the installationdetails table,See page 5, i-VIEW J2534 VCI Device Installation Details

• DLL Version: SPX T-### #.#.#.#

• Firmware Version: #.#.#



28





DA J2534 VCI Device

For details regarding the latest installation software and firmware level for the VehicleCommunication Interface (VCI) device,

See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details








5. Locate ‘DA J2534 Software’ in the software listing6. Select ‘DA J2534 Software’



8. Using the ‘Support Info’, confirm the current Software Driver Level information stated onscreen and compare it to that identified in the installation details table,See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details

• If the Software Driver Level version matches the required level, go to step 6 of:

Verifying DA App Hub Level• If the Software Driver Level version is not to the required level, complete the followingsteps 1 to 22 of: Updating Software Driver Level



2. Close the ‘Support Info’ pop up window


4. An ‘Add or Remove Programs’ message pop up window will be displayed

5. Select ‘Yes’6. A pop up window will be displayed with a progress scroll bar and will close automatically

once completed








29





Note: DA-ST512 uses the Davina driver

14. Select ‘DA Dongle and Davina’

15. A pop up window will be displayed - ‘Welcome to the DA J2534 software setup wizard’,select ‘Next’

16. A pop up window will be displayed - ‘Select Installation Folder’, select ‘Next’




20. Select ‘Close’ on the ‘Installation Complete’ pop up window


22. Go to step 1 of: Verifying DA App Hub Level

DA App Hub Level

Verifying DA App Hub Level





Note: The ‘Add or Remove Programs’ control panel displays a list of software on the

SDD machine5. Locate ‘DA App Hub’ in the software listing


7. Select ‘Select here for support information’

Note: ‘Support Info’ will be displayed in a pop up window stating the DA App Hub VersionLevel

8. Using the ‘Support Info’, confirm the current DA App Hub Level information stated onscreen and compare it to that identified in the installation details table,See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details

• If the DA App Hub Level version matches the required level, close all open windowsand go to step 1 of: Verifying DA Firmware Level

• If the DA App Hub Level version is not to the required level, complete the followingsteps 1 to 29 of: Updating DA App Hub Level

Updating DA App Hub Level





30






6. Select ‘Yes’





11. Select and open ‘Internet Explorer’

12. In the Internet Explorer address bar, enter the following:

• http://www.diagnostic-associates.com/pages/downloads

13. Select the appropriate Language ‘Download’ link at the bottom of the ‘DA App Hub Setup’section

14. A pop up window will be displayed - ‘File Download’, select ‘Save’

15. A pop up window will be displayed -‘Save As’, select ‘Desktop’

16. Select ‘Save’ and save the latest ‘DAAppHub’ .zip file to the SDD Desktop

17. Once the Download has completed, select ‘Close’

18. Press the ‘Windows Key’ and the ‘D’ key at the same time

Note: This will now display the SDD desktop

19. Open the ‘DAAppHub’ .zip file saved to the SDD Desktop

20. Open ‘DAAppHubSetup’, select ‘Run’

21. A pop up window will be displayed - ‘Open File - Security Warning’, select ‘Run’

22. A pop up window will be displayed - ‘Welcome to DA App Hub Setup Wizard’, select‘Next’

23. A pop up window will be displayed - ‘Select Installation folder’, select ‘Everyone’ and thenselect ‘Next’



26. A pop up window will be displayed - ‘Installation Complete’, select ‘Close’

27. Close all open windows


29. Go to step 1 of: Verifying DA Firmware Level

31





DA Firmware Level

Verifying DA Firmware Level


Note: Make sure the VCI device is not connected to a vehicle




5. Select ‘Diagnostic Associates Ltd’


7. A ‘DA App Hub’ pop up window will be displayed

8. A message in the ‘Home’ window will identify if the DA Firmware Level requires updating

• If the DA Firmware Level version is up to date, close all open windows and go to step1 of: DA J2534 VCI Device to SDD Machine Recognition and Final Checks

• If the DA Firmware Level version needs updating, complete the following steps 1 to 6of: Updating DA Firmware Level

Updating DA Firmware Level

1. Within the ‘DA App Hub’, select ‘Update Applications’

2. Select ‘Update Device’

3. Allow the software update process to complete

4. A pop up window will confirm the update has completed5. Close the pop up window

6. Go to step 1 of: DA J2534 VCI Device to SDD Machine Recognition and Final Checks

32





DA J2534 VCI Device to SDD Machine Recognition and Final Checks

1. Connect the VCI Device to the vehicle

2. Connect the VCI Device to the SDD machine using the USB cable



5. Login to SDD





10. Select ‘Connected’ next to ‘DA-Dongle or DAVINA2’

Note: DA-ST512 and DAVINA3 will be detailed as a DAVINA2

11. Make sure the information stated on screen matches that identified in the installationdetails table,See page 6, Diagnostic Associates (DA) J2534 VCI Device Installation Details

• DA-Dongle or DAVINA2

• DLL Version: #.##

• Firmware Version: ##.#


13. If the software information is confirmed as being incorrect, restart the software updating

process, See Installation Level Verification Actions

33





Drew Tech Mongoose Pro JLR J2534 VCI Device


See page 7, Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details








5. Locate ‘J2534 MongoosePro JLR’ in the software listing6. Select ‘J2534 MongoosePro JLR’



8. Using the ‘Support Info’, confirm the current Software Driver Level information stated onscreen and compare it to that identified in the installation details table,See page 7, Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details

Note: Make sure no other installs of MongoosePro JLR or Mongoose JLR are visible in

the software listing. Other installs could cause a software conflict and must be removed.Complete the following steps 1 to 21 of: Updating Software Driver Level

• If the Software Driver Level version matches the required level, go to step 1 of: DrewTech Mongoose Pro JLR J2534 VCI to SDD Machine Recognition and FinalChecks’

• If the Software Driver Level version is not to the required level, complete the followingSteps 1 to 22 of: Updating Software Driver Level





Note: Uninstall MongoosePro JLR, MongoosePro Jaguar or Mongoose JLR if listed

4. An ‘Add or Remove Programs’ message box will be displayed

5. Select ‘Yes’





34









14. Select ‘DrewTech Mongoose’

15. A pop up window will be displayed - ‘Welcome to the MongoosePro JLR setup wizard’,select ‘Next’



18. A pop up window will be displayed - ‘Please attach your device to the computer any timeafter the installation has finished’

Note: Do not connect the Mongoose Pro JLR device at this time

19. Select ‘Ok’



22. Go to step 1 of: Drew Tech Mongoose Pro JLR J2534 VCI Device to SDD DeviceRecognition and Final Checks

Drew Tech Mongoose Pro JLR J2534 VCI Device to SDD Machine Recognition andFinal Checks

1. Connect the VCI device to the vehicle2. Connect the VCI device to the SDD machine with the USB cable



5. Login to SDD





10. Select ‘Connected’ next to ‘MongooseProJLR’11. Make sure the information stated on screen matches that identified in the installation

details table,See page 7, Drew Tech Mongoose Pro JLR J2534 VCI Device Installation Details

• DLL Version: MongoosePro JLR J2534 Library V#.#.#.#

• Firmware Version: MongoosePro JLR FW:#.#.#.#



35





JLR J2534 VCI Device


See page 8, JLR J2534 VCI Device Installation Details








5. Locate ‘JLR VCI’ in the software listing6. Select ‘JLR VCI’



8. Using the ‘Support Info’, confirm the current Software Driver Level information stated onscreen and compare it to that identified in the installation details table,See page 8, JLR J2534 VCI Device Installation Details

• If the Software Driver Level matches the required level, go to step 1 of: JLR J2534

VCI Device to SDD Machine Recognition and Final Checks• If the Software Driver Level is not to the required level, complete the following steps1 to 22 of: Updating Software Driver Level






5. Select ‘Yes’6. A pop up window will be displayed with a progress scroll bar and will close automatically

once completed








36






15. A pop up window will be displayed - ‘Welcome to the JLR VCI setup wizard’ - select ‘Next’

16. A pop up window will be displayed - ‘Select Installation Folder’, select ‘Everyone’ andthen select ‘Next’






22. Go to step 1 of: JLR J2534 VCI Device to SDD Machine Recognition and Final Checks

JLR J2534 VCI Device to SDD Machine Recognition and Final Checks1. Connect the VCI device to the vehicle




5. Login to SDD





10. Select ‘Connected’ next to ‘JLR VCI’

11. Make sure the information stated on screen matches that identified in the installationdetails table,See page 8, JLR J2534 VCI Device Installation Details

• DLL Version: #.#.#

• Firmware Version: #.#




Documents

599852 VCI Update Instructions