58751494 Craftsman Garage Door Opener 139 53910 Manual

Embed Size (px)

Text of 58751494 Craftsman Garage Door Opener 139 53910 Manual

  • Owner's Manual/Manual Del Propietario

    1/2 HP

    GARAGE DOOR OPENERABRIDOR DE PUERTA DE COCHERAFor Residential Use Oniy/Sbio para uso residencial

    Model/Modelo 139.53910

    m

    I11o_

    Z_

    Read and follow all safety rulesand operating instructions beforefirst use of this product.

    Fasten the manual near the garagedoor after installation.

    Periodic checks of the opener arerequired to ensure safe operation.

    Leer y seguir todas ias regias deseguridad y las instrucciones deoperacibn antes de usar esteproducto por primera vez.Guardar este manual cerca de lapuerta de la cochera.

    Se deben realizar revisionesperibdicas del abridor de puertaspara asegurar su operacibnsegura.

    Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.Awww.sears.com/craftsman

  • TABLE OF CONTENTSIntroduction 2.7

    Safety symbol and signal word review ........................ 2Preparing your garage door ........................................ 3Tools needed ............................................................... 3Planning .................................................................. 4-5Carton inventory .......................................................... 6Hardware inventory ..................................................... 7

    Assembly 8-11Assemble the rail and install the trolley ...................... 8Fasten the rail to the motor unit andinstall the idler pulley ................................................... 9install the chain/cable ................................................ 10Tighten the chain ....................................................... 11Installation 11.26installation safety instructions .................................... 11Determine the header bracket location ..................... 12install the header bracket .......................................... 13Attach the rail to the header bracket ......................... 14Position the opener ................................................... 15Hang the opener ....................................................... 16install the door control ............................................... 17

    install the light ........................................................... 18Attach the emergency release rope and handle ....... 18Electrical requirements .............................................. 19install The Protector System .............................. 20-22Fasten the door bracket ....................................... 23-24Connect the door arm to the trolley ..................... 25-26

    Adjustment 27.29Adjust the travel limits ............................................... 27Adjust the force ......................................................... 28Test the safety reversal system ................................. 29Test The Protector System ...................................... 29

    Operation 30.34Operation safety instructions ..................................... 30Using your garage door opener ................................ 30Using the walt-mounted Door Control ....................... 31To open the door manually ........................................ 31Care of your garage door opener .............................. 32Having a problem? .................................................... 33Diagnostic chart ......................................................... 34

    Programming 35-36To add or reprogram a hand-held remote control .....35To erase all codes ..................................................... 353-Function Remotes .................................................. 35To add, reprogram or changea Keyless Entry PIN .................................................. 36

    Repair Parts 37.38Rail assembly parts ................................................... 37installation parts ........................................................ 37Motor unit assembly parts ......................................... 38

    Accessories 39

    Warranty

    Repair Parts and Service

    39

    40

    INTRODUCTIONSafety Symboland Signal Word ReviewThis garage door opener has been designed and tested to offer safe service provided it is installed, operated,maintained and tested in strict accordance with the instructions and warnings contained in this manual.

    Mechanical

    Electrical

    When you see these Safety Symbols and SignalWords on the following pages, they will alert you tothe possibility of serious injury or death if you donot comply with the warnings that accompany them.The hazard may come from something mechanicalor from electric shock. Read the warnings carefully.

    When you see this Signal Word on the followingpages, it will alert you to the possibility of damage toyour garage door and/or the garage door opener ifyou do not comply with the cautionary statementsthat accompany it. Read them carefully.

    2

  • Preparing your garage door

    Before you begin: Disable locks Remove any ropes connected to garage door Complete the following test to make sure your

    garage door is balanced and is not sticking orbinding:1 Lift the door about halfway as shown. Release

    the door. If balanced, it should stay in place,supported entirely by its springs.

    2 Raise and lower the door to see if there is anybinding or sticking

    If your door binds, sticks, or is out of balance, call atrained door systems technician.

    Sectional Door

    To prevent possibleSERIOUSINJURY or DEATH: ALWAYScall a trained door systems technician if

    garage door binds, sticks, or is out of balance.Anunbalancedgaragedoor may not reversewhenrequired

    NEVERtry to loosen, move or adjust garage door, doorsprings, cables, pulleys, brackets or their hardware, allof which are under EXTREMEtension.

    DisableALL locks and remove ALL ropes connected togarage door BEFOREinstalling and operating garagedoor opener to avoid entanglement.

    To preventdamage to garagedoor and opener: ALWAYSdisable locks BEFOREinstalling and operating

    the opener. ONLYoperate garagedoor openerat 120V,60 Hz to

    avoid malfunction and damage

    One-Piece Door Tools needed

    During assembly, installation and adjustment of theopener, instructions will call for hand tools asillustrated below.

    Stepladder

    Pencil

    Level (optionml)Tape Measure

    Hack Smw

    Screwdriver

    o)Adjustable End Wrench

    3

  • Planning

    Identify the type and height of your garage door.Survey your garage area to see if any of theconditions below apply to your installation. Additionalmaterials may be required. You may find it helpful torefer back to this page and the accompanyingillustrations as you proceed with the installation ofyour opener.Depending on your requirements, there are severalinstallation steps which may call for materials orhardware not included in the carton.

    Installation Step 1 - Look at the wall or ceilingabove the garage door. The header bracket mustbe securely fastened to structural supports.

    Installation Step 5 - Do you have a finished ceilingin your garage? If so, a support bracket andadditional fastening hardware may be required.

    Installation Step 10 - Depending upon garageconstruction, extension brackets or wood blocksmay be needed to install sensors.

    Installation Step 10 -Alternate floor mounting ofthe safety reversing sensor will require hardwarenot provided.

    Do you have an access door in addition to thegarage door? If not, Model 53702 Emergency KeyRelease is required. See Accessories page.Look at the garage door where it meets the floor.Any gap between the floor and the bottom of thedoor must not exceed 1/4" (6 mm). Otherwise, thesafety reversal system may not work properly. SeeAdjustment Step 3. Floor or door should berepaired.

    SECTIONAL DOOR INSTALLATIONSDo you have a steel, aluminum, fiberglass or glasspanel door? If so, horizontal and verticalreinforcement is required (Installation Step 11).The opener should be installed above the center ofthe door. If there is a torsion spring or centerbearing plate in the way of the header bracket, itmay be installed within 4 feet (1.22 m) to the left orright of the door center. See Installation Steps 1and 11.

    If your door is more than 7 feet (2.13 m) high, seerail extension kits listed on Accessories page.

    SECTIONAL DOOR INSTALLATION

    FINISHED CEILING

    Horizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum, door withglass panels, etc.). See page 23 for details.

    Header Wall

    Slack in chain tensionis normal whengarage door is closed.

    fastening hardwareis required.See page 16.

    ORf Torsion Spring

    Motor unit

    Wall-

    DoorContro

    Gap between floorand bottom of doormust not exceed 1/4" (6 mm).

    Safety ReversingSensor

    Access Door

    }aderall

    Header CLOSED POSITIONBracket

    TrolleyStop Bolt Trolley

    Garage

    sOOn g ChainP g 2

    o Straig Emergency_i_g _m el Release

    _ _id _ Rope& HandleDoorArm

    Door_rage)or

    4

  • Planning (Continued)

    ONE-PIECE DOOR INSTALLATIONS Generally, a one-piece door does not require

    reinforcement. If your door is lightweight, refer tothe information relating to sectional doors inInstallation Step 11.

    Depending on your door's construction, you mayneed additional mounting hardware for the doorbracket (Step 11).

    Without a properly working safety reversalsystem,persons (particularly small children) could beSERIOUSLYINJUREDor KILLEDby a closing garagedoor. The gap betweenthe bottom of the garagedoor and

    the floor MUST NOTexceed 1/4" (6 ram). Otherwise,the safety reversalsystem may not work properly.

    The floor or the garagedoor MUST be repairedtoeliminate the gap.

    ONE-PIECE DOOR WITHOUT TRACKFINISHED CEILING

    Support bracket& faste