Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
1 of 6
5555200 TORK® TWIN MINI JUMBO TISSUE DISPENSER, WHITE
5555290 TORK® TWIN MINI JUMBO TISSUE DISPENSER, BLACK
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
2 of 6
Dispenser Part List
PART DESCRIPTION PART NUMBER
Left/Right roll arm Not replaceable
Spindle Not replaceable
Paper access door Not replaceable
Hood (White) Hood (Black) (does not include new lock)
2255560 2255570
200260 Metal Tork Key 200260KEY
Tork Elevation Lock (White) Tork Elevation Lock (Black)
205502 205503
Part Description with Replacement Instructions Parts with “Spare Part Number” are available for order as of the revision date on the manual. Contact your SCA Sales Representative or SCA Customer Service Representative to order these parts.
Replacing the Elevation Lock: 205502 (White); 205503 (Black)
1 2 3 4
1. Use a small slot-head screwdriver to press the snap fit towards the lock housing. Push the lock downwards at the same time.
2. Repeat the procedure on the other side of the lock. 3. Remove the old lock by pulling it through the hole in the cover. 4. Insert the new lock. Push until a click sound is heard.
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
3 of 6
Replacing the Hood (2255560 White; 2255570 Black)
1. Using a Phillips head screwdriver, remove the two screws holding the door to the dispenser housing. 2. Follow steps above to remove Elevation lock from cover. 3. Follow steps above to insert Elevation lock into replacement cover. 4. Fit cover on dispenser housing, replace and tighten screws with Phillips head screwdriver to secure cover.
Troubleshooting Problem: Any paper-related problem
Take note of the date code on the outside of the case of refill product. Contact your SCA Customer Service Representative for complaint resolution.
Problem: Any dispenser-related problem
Locate the Tork label inside the dispenser. Note the Model Number and the date code. Contact your SCA Customer Service Representative for complaint resolution.
This is a TorkSelect product. The TorkSelect label is affixed to the inside, right side of the dispenser. The system identifier (to match product refills) and the dispenser item number are printed on the bottom of this label. SCA only guarantees dispenser performance if used with genuine Tork refills.
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
4 of 6
Mounting Instructions
Recommended mounting height for standard access is 35” above finished floor to upper drilling hole location. Mount dispenser securely using four attachment points - two upper and two lower. Full size drilling hole template is located inside dispenser carton.
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
5 of 6
Mounting Instructions – ADAAG Guidelines
604.7 Dispensers. Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be 15 inches (380 mm) minimum and 48 inches (1220 mm) maximum above the finish floor and shall not be located behind grab bars. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow.
Figure 604.7 Dispenser Outlet Location
Advisory 604.7 Dispensers. If toilet paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of the gripping surface of the grab bar must be 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor.
609.3 Spacing. The space between the wall and the grab bar shall be 1 1/2 inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1 1/2 inches (38 mm) minimum. The space between the grab bar and projecting objects above shall be 12 inches (305 mm) minimum.
Figure 609.3 Spacing of Grab Bars
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
6 of 6
609.4 Position of Grab Bars. Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except that at water closets for children's use complying with 604.9, grab bars shall be installed in a horizontal position 18 inches (455 mm) minimum and 27 inches (685 mm) maximum above the finish floor measured to the top of the gripping surface.
604.9.6 Dispensers. Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be 14 inches (355 mm) minimum and 19 inches (485 mm) maximum above the finish floor. There shall be a clearance of 1 1/2 inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow.
5555200 and 5555290 meet ADA technical requirements for operation and pull force Compliance with ADA mounting guidelines is the responsibility of the installer and building owner. Local and state requirements may differ from ADAAG guidelines.
Additional Technical Data Sheets: Tork Elevation T2 Mini ADA Mounting Height Tork Dispenser Bath Tissue Mini Twin Jumbo Roll – Mounting and Filling Instructions 5555290 Specification Sheet
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
3 of 6
Replacing the Hood (2255560 White; 2255570 Black)
1. Using a Phillips head screwdriver, remove the two screws holding the door to the dispenser housing. 2. Follow steps above to remove Elevation lock from cover. 3. Follow steps above to insert Elevation lock into replacement cover. 4. Fit cover on dispenser housing, replace and tighten screws with Phillips head screwdriver to secure cover.
Troubleshooting Problem: Any paper-related problem
Take note of the date code on the outside of the case of refill product. Contact your SCA Customer Service Representative for complaint resolution.
Problem: Any dispenser-related problem
Locate the Tork label inside the dispenser. Note the Model Number and the date code. Contact your SCA Customer Service Representative for complaint resolution.
This is a TorkSelect product. The TorkSelect label is affixed to the inside, right side of the dispenser. The system identifier (to match product refills) and the dispenser item number are printed on the bottom of this label. SCA only guarantees dispenser performance if used with genuine Tork refills.
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
4 of 6
Mounting Instructions
Recommended mounting height for standard access is 35” above finished floor to upper drilling hole location. Mount dispenser securely using four attachment points - two upper and two lower. Full size drilling hole template is located inside dispenser carton.
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
5 of 6
Mounting Instructions – ADAAG Guidelines
604.7 Dispensers. Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be 15 inches (380 mm) minimum and 48 inches (1220 mm) maximum above the finish floor and shall not be located behind grab bars. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow.
Figure 604.7 Dispenser Outlet Location
Advisory 604.7 Dispensers. If toilet paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of the gripping surface of the grab bar must be 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor.
609.3 Spacing. The space between the wall and the grab bar shall be 1 1/2 inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1 1/2 inches (38 mm) minimum. The space between the grab bar and projecting objects above shall be 12 inches (305 mm) minimum.
Figure 609.3 Spacing of Grab Bars
Tork Elevation Technical Service Manual Twin Mini Jumbo Tissue Dispenser, T2 System 5555200; 5555290 Revision Date: May, 2013
6 of 6
609.4 Position of Grab Bars. Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except that at water closets for children's use complying with 604.9, grab bars shall be installed in a horizontal position 18 inches (455 mm) minimum and 27 inches (685 mm) maximum above the finish floor measured to the top of the gripping surface.
604.9.6 Dispensers. Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser. The outlet of the dispenser shall be 14 inches (355 mm) minimum and 19 inches (485 mm) maximum above the finish floor. There shall be a clearance of 1 1/2 inches (38 mm) minimum below the grab bar. Dispensers shall not be of a type that controls delivery or that does not allow continuous paper flow.
5555200 and 5555290 meet ADA technical requirements for operation and pull force Compliance with ADA mounting guidelines is the responsibility of the installer and building owner. Local and state requirements may differ from ADAAG guidelines.
Additional Technical Data Sheets: Tork Elevation T2 Mini ADA Mounting Height Tork Dispenser Bath Tissue Mini Twin Jumbo Roll – Mounting and Filling Instructions 5555290 Specification Sheet
Tork Twin 55552
Repla
1. U2. F3. F4. F
Tro Prob
TR
Prob
LS
This iidentguara
Elevation TechMini Jumbo Ti200; 5555290
acing the Hoo
Using a PhillipFollow steps aFollow steps aFit cover on d
oubleshoo
lem: Any pap
Take note of tRepresentativ
lem: Any dis
Locate the ToService Repre
is a TorkSelectifier (to matcantees dispen
hnical Service Mssue Dispense
od (2255560
ps head screwabove to remabove to inseispenser hou
oting
per‐related p
the date codeve for compla
penser‐relate
rk label insideesentative for
ct product. Tch product renser perform
Manual r, T2 System
White; 22555
wdriver, remoove Elevationrt Elevation losing, replace
roblem
e on the outsiint resolution
ed problem
e the dispenscomplaint re
he TorkSelectefills) and the ance if used w
570 Black)
ove the two scn lock from coock into replaand tighten s
ide of the casn.
ser. Note theesolution.
t label is affixdispenser itewith genuine
3 of 6
crews holdingover. acement covescrews with P
se of refill pro
e Model Numb
xed to the insem number arTork refills.
g the door to
er. Phillips head s
oduct. Contac
ber and the d
ide, right sidere printed on
the dispense
screwdriver t
ct your SCA C
date code. Co
e of the dispen the bottom
Revision Da
er housing.
o secure cove
Customer Serv
ontact your S
enser. The syof this label.
ate: May, 201
er.
vice
CA Customer
stem SCA only
3
r
Tork Twin 55552
Mo
RecoMounlocat
Elevation TechMini Jumbo Ti200; 5555290
ounting In
ommended mnt dispenser sted inside disp
hnical Service Mssue Dispense
nstruction
ounting heighsecurely usingpenser carton
Manual r, T2 System
ns
ht for standardg four attachm
n.
d access is 3ment points -
4 of 6
5” above finistwo upper an
shed floor to und two lower.
upper drilling Full size dril
Revision Da
hole locationling hole temp
ate: May, 201
. plate is
3
Tork Twin 55552
Mo
604.7inchedispebe lopape
Advispapegrab
609.3grab grab
Elevation TechMini Jumbo Ti200; 5555290
ounting In
7 Dispensers.es (230 mm) menser shall beocated behinder flow.
sory 604.7 Dier dispenser mbar must be
3 Spacing. Thbar and projebar and proje
hnical Service Mssue Dispense
nstruction
. Toilet papemaximum in fe 15 inches (3d grab bars. D
ispensers. If must be 48 inc33 inches (84
he space betwecting objectsecting objects
Manual r, T2 System
ns – ADAA
r dispensers sfront of the w80 mm) miniDispensers sh
Fig
toilet paper dches (1220 m40 mm) minim
ween the wals below and as above shall
AG Guide
shall comply wwater closet mmum and 48 all not be of a
gure 604.7 Dis
dispensers armm) maximummum and 36 i
l and the grabat the ends shbe 12 inches
Figure 609.3
5 of 6
elines
with 309.4 anmeasured to tinches (1220a type that co
spenser Outl
e installed abm above the fnches (915 m
b bar shall behall be 1 1/2 i (305 mm) m
Spacing of G
nd shall be 7 ithe centerline0 mm) maximontrols delive
et Location
bove the side finish floor anmm) maximum
e 1 1/2 inchesinches (38 mminimum.
Grab Bars
inches (180 me of the dispeum above theery or that do
wall grab band the top of tm above the f
s (38 mm). Thm) minimum
Revision Da
mm) minimumenser. The oue finish floor oes not allow
r, the outlet othe gripping sfinish floor.
he space betw. The space b
ate: May, 201
m and 9 utlet of the and shall notcontinuous
of the toilet surface of the
ween the between the
3
t
e
Tork Twin 55552
609.4inchecloseminim
604.9inchedispebe a deliv
5555 Comrequ
Add Tork Tork 5555
Elevation TechMini Jumbo Ti200; 5555290
4 Position of es (915 mm) mets for childremum and 27
9.6 Dispenseres (230 mm) menser shall beclearance of ery or that do
5200 and 555
pliance with irements ma
ditional T
Elevation T2
Dispenser Ba
5290
hnical Service Mssue Dispense
Grab Bars. Gmaximum abn's use compinches (685 m
rs. Toilet papmaximum in fe 14 inches (31 1/2 inches oes not allow
5280 meet A
ADA mountiy differ from
Technical
Mini ADA Mo
ath Tissue Min
Specificatio
Manual r, T2 System
rab bars shalove the finishlying with 60mm) maximum
per dispenserfront of the w55 mm) mini(38 mm) min
w continuous p
DA technical
ng guidelines ADAAG guid
Data She
ounting Heigh
ni Twin Jumb
n Sheet
l be installed h floor measu4.9, grab barm above the f
rs shall complwater closet mmum and 19 imum below paper flow.
requirement
s is the respodelines.
eets:
ht
o Roll – Mou
6 of 6
in a horizontured to the tos shall be instfinish floor m
y with 309.4 measured to tinches (485 mthe grab bar.
ts for operati
nsibility of th
nting and Fill
tal position, 3op of the gripptalled in a homeasured to th
and shall be the centerlinemm) maximu. Dispensers
ion and pull f
he installer a
ing Instructio
33 inches (840ping surface, rizontal posithe top of the
7 inches (180e of the dispem above the shall not be o
force
nd building o
ons
Revision Da
0 mm) minimexcept that ation 18 inches gripping surf
0 mm) minimenser. The oufinish floor. of a type that
owner. Local
ate: May, 201
mum and 36 at water s (455 mm) face.
um and 9 utlet of the There shall t controls
and state
3
DispenserBath Tissue
Mini Twin Jumbo Roll
T2 System
T2 INSTRUCTION MANUAL 5/4/2011
SCA TISSUE NORTH AMERICAP.O. Box 2400, Neenah, Wisconsin 549571-866-SCA-TORK (1-866-722-8675) www.torkusa.com© 2011 SCA Tissue North America LLC. All Rights Reserved.Tork is a registered trademark of SCA Tissue North America LLC or its af�liates.
DispenserBath TissueMini Twin Jumbo RollT2 System
x1
x4
x4
SCA Tissue North Americawww.torkusa.com
T2 Mini Twin
35” (89 cm)
Floor
DispenserBath Tissue
Mini Twin Jumbo Roll
T2 System
T2 INSTRUCTION MANUAL 5/4/2011
SCA TISSUE NORTH AMERICAP.O. Box 2400, Neenah, Wisconsin 549571-866-SCA-TORK (1-866-722-8675) www.torkusa.com© 2011 SCA Tissue North America LLC. All Rights Reserved.Tork is a registered trademark of SCA Tissue North America LLC or its af�liates.
1
SCA Tissue North Americawww.torkusa.com
T2 Mini Twin
35” (89 cm)
Floor
SCA Tissue North Americawww.torkusa.com
T2 Mini Twin
35” (89 cm)
Floor
35” (89 cm)
1.
2.
Installation Instructions
2
T2 INSTRUCTION MANUAL 5/4/2011
SCA TISSUE NORTH AMERICAP.O. Box 2400, Neenah, Wisconsin 549571-866-SCA-TORK (1-866-722-8675) www.torkusa.com© 2011 SCA Tissue North America LLC. All Rights Reserved.Tork is a registered trademark of SCA Tissue North America LLC or its af�liates.
Features and Benefits
Technical Specifications
Technical Specifications (cont.)
Because our products make life easier for you and for millions of people around the
world. Because our resources and the way we work are natural parts of the global lifecycle. And because we care.
SCA TISSUE NORTH AMERICAP.O. Box 2400, Neenah, Wisconsin 549571-866-SCA-TORK (1-866-722-8675) www.torkusa.com© 2012 SCA Tissue North America LLC. All Rights Reserved. Tork is a registered trademark of SCA Tissue North America LLC 5/3/2013
5555290 - Tork Elevation Bath Tissue Jumbo Roll Mini Twin Dispenser, Black
Introducing a way to decrease labor and maintenance in high-traffic restrooms. Tork Elevation Bath Tissue Jumbo Roll Mini Twin Dispenser features two high-capacity rolls and a roll brake so people only take what they need. That means less waste, less mess, and less effort. The dispensers simplify and complement any environment, providing a clean, hygienic appearance. Our new design ensures easy and intuitive maintenance, refilling and use. Unique tear feature eliminates risk of cutting or scratching hands. Rolls are protected so there is less waste, improved hygiene and reduced pilferage. Durable plastic dispensers provide low maintenance and trouble free service.
Replaces 247550 and 555528A.
Also Available in White 5555200.
Brand Name: Tork® Elevation[TM]Product Number: 5555290System Identifier: T2 SystemTorkSelect: YesReplaces: 247550, 555528ADescription: Tork Elevation Bath Tissue Jumbo Roll Mini Twin DispenserColor: BlackMaterial: PlasticDispenser Dimensions HxWxD (Inches): 10.125 x 17.0 x 5.6875 (25.72 x 43.18 x 14.45 cm)Dispenser Capacity: 2 Rolls
Approx. Lbs. Per Case: 4.0 (1.8 kg)Cubic Feet Per Case: 0.62 (0.0175 cm)Approx. Product Net Wt Per Case: 3.27 (1.5 kg)Dispensers Per Tier: 32Cases Per Tier: 32Tiers Per Unit Load: 5Unit Order Quantity (Cases): 160Case Dimensions LxWxH (Inches): 10.0 x 6.125 x 17.625 (25.40 x 15.56 x 44.77 cm)Dispenser Key Number: 200260Meets ADA Technical Requirements: YesProduct Options: 11020602, 12013903, 12024402, 120246Shipping Container Code: 100 73286 62449 6Inner Pack UPC: N/AAdditional Info: This is a TorkSelect Product; a signed agreement is required. All specifications are subject to change without notice.12/1/2011