532_212_a_gb

AFFICHEURS DPORTS - REMOTE INTERFACESATyS D10 & D20

Notice dutilisation - Operating instructionsF GB

SOCOMEC GROUP SWITCHING PROTECTION & UPS

MAKE YOUR BUSINESS SAFE

532_212_a 9/02/05 9:00 Page 1

SOCOMEC - Rf. : 532 212 A2

PRSENTATION GNRALE ATyS D10 et D20 _______3INSTALLATION ATyS D10 et D20 ___________________4

Montage _______________________________________4Raccordements _________________________________4Caractristiques_________________________________4

UTILISATION ATyS D10 ___________________________5Affichage_______________________________________5

UTILISATION ATyS D20 ___________________________6Affichage_______________________________________6Clavier _________________________________________7Version logiciel __________________________________7Programmation _________________________________8Exploitation____________________________________18Fonctionnement________________________________20Visualisation ___________________________________20

Som

mai

re

F

GENERAL PRESENTATION ATyS D10 & D20________23INSTALLATION ATyS D10 & D20___________________24

Mounting _____________________________________24Connection____________________________________24Characteristics_________________________________24

OPERATION ATYS D10___________________________25Display _______________________________________25

OPERATION ATyS D20 ___________________________26Display _______________________________________26Keypad _______________________________________27Software version _______________________________27Programming __________________________________28Control and Test modes_________________________38Operational sequences__________________________40Visualisation ___________________________________40

Sum

mar

y

GB

532_212_a 9/02/05 9:00 Page 2

ATyS D10 and D20 models are remote interfacesdesigned for easy integration on front panels. They canbe connected to ATyS 6e, 6m and C30 products to allowremote access to display or control features.

23SOCOMEC - Rf.: 532 212 A

Remote interfaces ATySGENERAL PRESENTATIONATyS D10 & D20

532_212_a 9/02/05 9:00 Page 23

Mounting

Door fixing: 2 holes, diameter 22.5 mm Maximum thickness of the door: 20 mm

Connection

Connection only on AtyS 6e, 6m or C30 products.

> CableRJ45 type 8/8 not isolated

> Maximum cable length3 m

> Tightning torque4 N.m

Characteristics

> IPIP21 standardIP54 using gasket

> Operation Temperature: -10 to + 55 C hygrometry: 80% humidity at 55 C

95% humidity at 40 C

Remote interfaces ATySINSTALLATIONATyS D10 & D20

24 SOCOMEC - Rf.: 532 212 A

1

ATY

S 1

47 A

(1) RJ45 plug for ATyS connection

22.5

4036

20

= =

96 x 96

ATY

S 1

61 A

Door drilling

ATyS C30

Type RJ45

ATyS D10/D20

43

21

ATY

S 3

13 A

GB

532_212_a 9/02/05 9:00 Page 24

25SOCOMEC - Rf.: 532 212 A

ATyS D10 allows remote display of transfer systempositions, sources availability and operational mode.Programming and operations remain available directly onmaster product (ATyS 6e, 6m or C30).

Remote interfaces ATySOPERATIONATyS D10

Display

Source 1 available Power On

ATyS Product faulty, transfer error Possible to reset after error

disappearance the power suppliesof the master product (ATyS 6e,6m, C30) for 3 minutes

Transfer system inposition 1

Transfer system inAutomatic mode



Source 2 available

ATY

S 1

45 B

532_212_a 9/02/05 9:00 Page 25


26 SOCOMEC - Rf.: 532 212 A

DisplayKeypadSoftware versionProgrammingControl and Test modesOperational sequencesVisualisation

Display

ATyS D20 allows remote display of transfer systempositions, sources availability, operational mode andmetering. Programming and operations (Test andControl) are also available. Master product (ATyS 6e, 6mor C30) display is deactivated as soon as the remoteinterface is connected.

Power On

Source 1 available

Manualmodeactive Padlock*

Product faulty, transfer error Possible to reset after error

disappearance: switch off thepower supplies of the masterproduct (ATyS 6e, 6m, C30)for 3 minutes


Transfer system inautomatic mode

Control mode active Test mode active Programming mode active

Transfer systemin position 0

Transfer systemin position 2

Source 2 available

ATY

S 1

46 B

* only on ATyS 6e and 6m

532_212_a 9/02/05 9:00 Page 26

Display

Software version

Keypad

Software version of the master product is displayedimmediately after ATyS 6e, 6m or C30 power on.

Access to AUT, Test,Control and Prog modes

Direct Access to Test and Controlfunctionalities or navigation

Allows main menu accessin visualisation mode orvalidation

Priority source

Informations source 1 source 2 sources 1 & 2(split screen)

Power factorCapacitive or inductive

Phases (wires) displayed Units

Values

Signedvalues(power)

ATY

S 3

18 A

ATY

S 1

46 C

ATY

S 3

19 A

Remote interfaces ATyS

OPERATION

27SOCOMEC - Rf.: 532 212 A

532_212_a 9/02/05 9:00 Page 27


28 SOCOMEC - Rf.: 532 212 A


> Enter into programming mode

Step 1: Press the mode push button until Prog led is blinking

Step 2: Press validation push button. PROG led becomes fixed and access code is displayed

Step 3: Enter access code (1000 factory default) using keypad left,right, top and bottom

Step 4: Press validation push button to enter programming mode

> Programming mode exit

Step 1: Press the ESC push button when not entering any value, to come back to mainprogramming menu

Step 2: Press again on ESC push button to exit programming

New Active mode (Automatic or Manual) depends on information from the master device (ATyS 6e, 6m ou C30)

Programming

532_212_a 9/02/05 9:00 Page 28

Programming

> Navigation in programming mode

Step 1: To access required menu, press navigation push buttonsleft and right

Step 2: To access parameter to modifypress navigation push buttons top and bottom

Step 3: To modify the parameter, press push button rightto make the required parameter blinking

Step 4: Press push buttons top and bottom to increment ordecrement the value of the parameter

Step 5: Press validation push button to validate

In case of parameter displayed on 2 lines, press validation push button after first line modificationto access next one

ESC push button allows to come back to main menu or to cancel the modification


OPERATION

29SOCOMEC - Rf.: 532 212 A

532_212_a 9/02/05 9:00 Page 29

Programming

ARCHITECTURE OF THE PROGRAMMING MENU


30 SOCOMEC - Rf.: 532 212 A


*

**** ** ** ** **

** **** **

**

** ** **

ATY

S 3

27 A

532_212_a 9/02/05 9:00 Page 30


OPERATION

31SOCOMEC - Rf.: 532 212 A

*on

ly o

n A

tys

6m**

optio

n on

ATy

S 6

e &

6m

***

only

on

ATyS

C30

****

visi

ble

if o

ptio

n LS

sel

ecte

d a

nd a

ctiv

e

** ** ** ** ****

**

***

***

***

532_212_a 9/02/05 9:00 Page 31

Programming

VARIABLES CHARACTERISTICS


32 SOCOMEC - Rf.: 532 212 A


> Setup

LCD Denomination Setting range Default values

nt Type of network 1BL, 2BL, 2NBL 4NBL(cf. ATyS 6 or C30 instruction manual) 3NBL, 4NBL,

41NBL, 42NBL

Un Network Nominal voltage 100 to 480 V 400 VPhase-Neutral voltage for 1BL & 41NBLPhase-Phase voltage for others

ScE** Source 1 - Switch I or II configuration I, II ISource 1 (controlled and displayed) linked to switch I or II (depending on cabling)

Fn Network nominal Frequency 50 or 60 Hz 50 Hz

Ct* CTs primary current 50 to 5000/5 A 500/5 A(5 A secondary CT)

Gen Genset start signal state NO, NC NONormally opened or closed

Pri Network priority selection 1, 2 1Keypad selection (1 or 2)Also possible via external contactUsing option

Mtf Manual Retransfer Yes, No NoActivation of the feature

LoG Type of control logic selection IMP, CON, brE*** IMPImpulse, contactor or breaker***

AC*** Number of position auxiliary contacts used, depending on transfer 0, 2, 3 2device type (switch, contactor, breaker)

rn1 Allows 0 position command after loss of main source (source 1) Yes, No No

rn2 Allows 0 position command after loss of emergency source (source 2) Yes, No No

CrS Number of permutation counter Reset Yes, No No

CP Programming code modification 0001 to 9999 1000Possible to change the code

* only on AtyS 6m** only on ATyS 6e & 6m*** only on ATyS C30.

532_212_a 9/02/05 9:00 Page 32

Programming

> Voltage thresholds

> Frequency thresholds


OPERATION

33SOCOMEC - Rf.: 532 212 A


oU Network 1 over voltage threshold 102 - 120% 115%

oUh Network 1 over voltage threshold hysteresis 101 - 119% 110%(< oU)

uU Network 1 under voltage threshold 80 - 98% 85%

uUh Network 1 under voltage threshold hysteresis 81 - 99% 95%(> uU)

oU Network 2 over voltage threshold 102 - 120% 115%

oUh Network 2 over voltage threshold hysteresis 101 - 119% 110%(< oU)

uU Network 2 under voltage threshold 80 - 98% 85%

uUh Network 2 under voltage threshold hysteresis 81 - 99% 95%(> uO)

Values defined are % of nominal values.Hysteresis thresholds must be programmed according to over and under voltage thresholds (respectively under & above).


oF Network 1 over frequency threshold 101 to 120% 105%

oFh Network 1 over frequency threshold hysteresis 100.5 - 119.5% 103%(< oF)

uF Network 1 under frequency threshold 80 - 99% 95%

uFh Network 1 under frequency threshold hysteresis 80.5 - 99.5% 97%(> uF)

oF Network 2 over frequency threshold 101 - 120% 105%

oFh Network 2 over frequency threshold hysteresis 100.5 - 119.5% 103%(< oF)

uF Network 2 under frequency threshold 80 - 99% 95%

uFh Network 2 under frequency threshold hysteresis 80.5 - 99.5% 97%(> uF)

Values defined are % of nominal values.Hysteresis thresholds must be programmed according to over and under frequency thresholds (respectively under & above).

532_212_a 9/02/05 9:00 Page 33

Programming


34 SOCOMEC - Rf.: 532 212 A


> Timers


Mft Main Failure Timer From 0 to 60 s 5 sDelays priority network failure detection

dtt Delay on transfer timer From 0 to 60 s 5 sEmergency network stability validation before transfer

OMf O Main Failure Timer From 0 to 20 s 0 sRest in O position when transferringfrom main network to emergency network

Mrt Main Return Timer From 0 to 30 min 1 minMain network stability validation before re-transfer

OMr O Main Return Timer From 0 to 20 s 5 sRest in O position when re-transferring from emergency network to main network

Cdt Cool Down Timer From 0 to 10 min 4 minAllows generator cooling down period after loadsretransfer from emergency source (generator) to Main source

> Communication


Add Device address 1 to 247 5

bd Communication speed 2400, 4800, 9600, 960019200, 38400

StoP Stop bit 1, 2 1

PAr Parity bit No, Odd, Even No

Only on ATyS 6e or 6m in case of optional communication module.

532_212_a 9/02/05 9:00 Page 34

Input (In2, Ft2) and output (Ou1, S1A) programming example:

Refer to ATyS C30, 6e or 6m instruction manualfor terminals identification.

Input/Output Function Relay State

I1 to I4 Ft1, Ft2, Ft3, Ft4, Pri, NO or NCMtf, S2A, Man, TOL, TFL, EJP, CTS

O1 to O4 S1A, S2A, LS, / NO

ATY

S 3

28 A

Step 1: Press right push button to makefirst variable blinking (Ft2 ou S1A)

Step 2: press top and bottompush buttons to modify the variable

Step 3: press validation

Step 4: press bottom push button toacces nO variable selection

Programming

> Inputs/Outputs 2 inputs (In1, In2) and 2 outputs (Ou1, Ou2) as standard

on ATyS C30.

Possibility to connect 2 modules 2 Inputs/2 Outputson ATyS 6e & 6m.

- First module: In1, In2, Ou1, Ou2- Second module In3, In4, Ou3, Ou4.


OPERATION

35SOCOMEC - Rf.: 532 212 A

532_212_a 9/02/05 9:00 Page 35

Outputs

Programming

Variables descriptionInputs


36 SOCOMEC - Rf.: 532 212 A


Variable Description

Ft1 Fault input 1. The fault led is blinking as soon as the input is active andFt1 is displayed on LCD. Reset when the input is de-activated

Ft2 Fault input 2. The fault led is blinking as soon as the input is active and Ft2 is displayed on LCD.Reset when the input is de-activated

Ft3* Fault input 3. The fault led is blinking as soon as the input is active and Ft3 is displayed on LCD. The transfer switch is immediately driven in 0 position.Keypad action (Esc) necessary to Reset the fault

Ft4* Fault input 4. The fault led is blinking as soon as the input is active and Ft4 is displayed on LCD. The transfer switch is immediately driven in 0 position.Keypad action (Esc) necessary to Reset the fault

Pri Priority network selection.Network 1 has priority when input is not activated. Network 2 has priority if input is active

Mtf Remote manuel re-transfer. Feature identical to manual re transfert on keypad.Re-transfer from priority network to backup network is allowed from input activation (1 s front).The Mtf variable in the setup menu must be selected (Yes) to allow input recognition

S2A Information source 2 available (Genset) used instead of voltage/ frequency measurementfrom ATyS (inhibited when S2A is selected)

Man** Information transfer system in manual mode.All automatic commands (+ test on load and control commands) are inhibited as soon as the input is activated

CTS** Remote transfer control. Possible to initiate transfer from priority source to backup sourcebefore DTT ends. If DTT is set to its maximum value (60s), the transfer is initiated as soon asthe input is activated (1 s front)

TOL** Remote test on load. Started from input activation.Re-transfer is blocked until input de-activation

TFL Remote test off load.Started from input activation (remote genset start /stop)

EJP 2 inputs one automatically affected to EJP input 1 for EJP advice, to start generator input 2 to transfer on emergency sourceRetransfer is activated when input 2 disapears

* only on ATyS C30, specific fault operation (Ft2 and Ft3)** only as option on ATyS C30, standard features on ATyS 6e et 6m.

Variable Description

S1A Source 1 available.Output activated as soon as source 1 is considered available (similar to front led source 1)

S2A Source 2 available.Output activated as soon as source 2 is considered available (similar to front led source 2)

LS Load shedding relay. LS timer corresponds to time available to disconnect the shed loads.The relay is activated before permutation on standby network according to LS timer.The relay is de-activated after retransfer on mains network and LS timer countdown

532_212_a 9/02/05 9:00 Page 36

Programming


OPERATION

37SOCOMEC - Rf.: 532 212 A

LOAD SHEDDING CONFIGURATIONLS variable allows associated LS timer configuration.

Output Associated funciton Setting range Default value

O1 to O4 LS 0 to 60 s ( DTT)* 2

> Example: load shedding configuration

function

timer

Step 1: Press right push button to makefirst variable blinking (LS)

Step 2: press push buttons top andbottom to modify the variable

Step 3: Press validation

Step 4: Press bottom push buttonto access timer value configuration

ATY

S 3

29 A

GB

* In case of DTT variable configuration below LS, LS will be automatically set to to DTT value.

532_212_a 9/02/05 9:00 Page 37

Control and Test modes

It is possible to start test sequences or to controlelectrically the changeover system from keypad.

NAVIGATION


38 SOCOMEC - Rf.: 532 212 A


> Enter Control or Test modes

Step 1: Press mode push button to make test or control led blinking

Step 2: Press validation push button to make control or test led become fixed

CONTROL MODE

Access code is displayed directly

TEST MODE

It is possible to test leds and LCD without entering any code by pressing directly

Test on load or test off load access codes are displayed after pressing or

Enter the code 4000 using left, right, topand bottom push buttons

Press validation push button to enter

532_212_a 9/02/05 9:00 Page 38

Control and Test modes

> Exit control or test modes

Press ESC push button

The new operational mode (automatic or manual) depends on information from masterATyS (6e, 6m ou C30)

> Control or Test modes use

Direct access by pressing and

To start a test (off load or on load) or to control the changeover switch electrically,

press , and push buttons


OPERATION

39SOCOMEC - Rf.: 532 212 A

532_212_a 9/02/05 9:00 Page 39

Operational sequences

Visualisation

Refer to ATyS 6e, 6m or C30 manuals for moreinformation on operational sequences and controls: sources control, tests cycles, loss of priority source sequence, priority source return sequence.

It is possible to display controlled parameters in bothautomatic and manual modes (but not during program-ming).No code is required to perform visualisation.Permutation cycles have priority over visualisation anddisplay timer countdown during cycle operation.

Without keypad activation or any operational sequenceduring 5 minutes, the LCD comes back to default displaymode and stops the backlight.

> If both sources are available: One visualisation screen is split into 2 parts and

displays simultaneously voltage and frequency valueson both networks.

If a timer is active, on one of the source, its count-down is displayed instead of voltage and frequencyvalues.

Examples:

> If only one source is present: During permutation cycle, voltage and frequency

values of the available source (active) are displayedon 2 lines. The name of the active timer and its count-down are displayed on remaining 2 lines.

Out of a permutation cycle, phase to phase voltagesand frequency are displayed.

Examples:


40 SOCOMEC - Rf.: 532 212 A


Press left, right, top & bottom push buttonsto access available screens

Press navigation push button to navigate in visualisation, displaying all available screens

ATY

S 3

31 A

ATY

S 3

32 A

532_212_a 9/02/05 9:00 Page 40

Visualisation

ARCHITECTURE OF VISUALISATION MENU


OPERATION

41SOCOMEC - Rf.: 532 212 A

*

**

***

****

***

***

***

***

* only on AtyS 6e & 6m** only U3-1 on AtyS C30*** only on ATyS 6m**** visible if option LS selected and active

ATY

S 3

33 A

532_212_a 9/02/05 9:00 Page 41

532_212_a 9/02/05 9:00 Page 42

532_212_a 9/02/05 9:00 Page 43

SOCOMEC - Ref.: 532 212 A - 02/05

This document is not contractual. SOCOMEC reservesthe right to modify features without prior notice in view ofcontinued improvements.

H E A D O F F I C ESOCOMEC GROUP SWITCHGEAR AND UPSS.A. capital 10 923 800 - R.C. Strasbourg 548500 149 B1, rue de Westhouse - B.P. 10 - 67235 Benfeld CedexTl. +33 03 88 57 41 41 Fax +33 03 88 57 78 78

S A L E S M A N A G E M E N T D I V I S I O NSOCOMEC95, rue Pierre Grange 94132 Fontenay-sous-Bois Cedex Tl. +33 01 45 14 63 90Fax +33 01 45 14 63 38

www.socomec.com

532_212_a 9/02/05 9:00 Page 44

Documents

532_212_a_gb