Fiche technique / Technical sheet UT‐5000 

Applica on  Résiden elle, Ins tu onnelle, Commerciale et Industrielle 

Residen al, Ins tu onnal, Commercial and Industrial 

Usage  Moyen/Robuste—Medium/Heavy duty 

Norme / Standard  Conforme—Complies with ANSI/BHMA A156.14 Grade 1 

Fiche technique/ Technical sheet UT‐5000 

Liste des pièces ensemble UT‐5000 / Parts list UT‐5000 

Nom / Name  Image / Picture  Qté / Qty 

Montant d’acier 

Steel upright   4 

Panneau de MDF 

MDF Board   1 

Boi er de tête 

Header track   1 

Chariot UT‐1010 

UT‐1010 Hanger   2 

Plaque de fixa on 

Fixing plate   2 

Support boi er de tête 

Header bracket   2 

Support de plancher 

Foot bracket   2 

Guide décentré UT‐1050 

Offset guide UT‐1050   2 

Guide centré UT‐1055 

UT‐1055 Center guide   2 

Écrou hexagonal 5/16’’ 

5/16’’ Hex nut   2 

Rondelle d’espacement 5/16’’ 

5/16’’ spacer washer   6 

Rondelle de blocage dentée 

Tooth washer   4 

Butoir UT‐5040 

UT‐5040 door stop   1 

Butoir UT‐DS100 

UT‐DS100 Door stop   2 

Vis auto‐perçante #10x2’’ 

Self‐drilling screw #10x2’’   4 

Vis HEX TEK #14x3/4’’ 

HEX TEK screw #14x3/4’’   8 

Vis auto‐perçante #10x1‐1/2’’ 

Self‐drilling screw #10x1‐1/2’’   6 

Vis #10x1‐1/4’’ 

Screw #10x1‐1/4’’   13 

Vis à gypse 1’’ 

1’’ drywall screw   25 

Vis #8x3/4’’ 

Screw #8x3/4’’   7 

Installa on Instruc ons for UT‐5000 Series Pocket Door

Hardware for 1‐3/8” and 1‐3/4” thick doors.

1‐Cut the header track to the required length. Required

length should be twice the width of the door minus 1/8”.

The opening width should correspond to twice the width

of the door plus 3/8”

2‐Mark the loca on of the header bracket UT‐5030 and

fix using #10 x 1‐1/4” screws. The height o the header

bracket should correspond to the height of the door plus

4‐7/16”

3‐Slide hangers UT‐1010 into header track. Make sure

that screw heads a aching hanger bolt are accessible and

on the same side of the opening (facing the exterior).

4‐Insert one end of the header track into the header

bracket installed in step 2. Level the header track. A er

levelling, install second header bracket and screw it to

the stud using #10 x 1‐1/4” screws.

Installa on Instruc ons for UT‐5000 Series Pocket Door

Hardware for 1‐3/8” and 1‐3/4” thick doors.

5‐Using #14 x ¾” HEX TEK screws, secure header track to the

header brackets installed in step 2 and 4.

6‐Using a chalk line, draw a line on the floor of the opening

on either side of the studs. Next, refer to table 1 to deter‐

mine loca on of foot brackets UT‐5020 and fix using #8 x ¾”

screws.

Door width  1st bracket  2nd bracket 

2'‐0" (610mm)  12‐7/16" (316mm)  24‐7/16" (621mm) 

2'‐2" (661mm)  13‐7/16" (341mm)  26‐7/16" (672mm) 

2'‐4" (711mm)  14‐7/16" (367mm)  28‐7/16" (722mm) 

2'‐6" (762mm)  16‐7/16" (418mm)  30‐7/16" (773mm) 

2'‐8" (813mm)  16‐7/16" (418mm)  32‐7/16" (824mm) 

2'‐10" (864mm)  18‐7/16" (468mm)  34‐7/16" (875mm) 

3'‐0" (915mm)  20‐7/16" (519mm)  36‐7/16" (926mm) 

TABLE 1

7‐Screw nylon guides onto the foot bracket located on

the side of the opening. Use the offset guides UT‐1050

for a 1‐3/4” door and the offset guides UT‐1055 for a 1‐

3/8” door.

8‐Install steel uprights into the foot brackets. The oval

holes in the uprights must face the outside of the wall. To

facilitate the installa on of drywall, the seam on the side

of the uprights must be facing the back of the pocket.

9‐Level the uprights and se‐

cure them to the header track

using toothed washers and

#14 x ¾” HEX TEK screws.

Installa on Instruc ons for UT‐5000 Series Pocket Door

Hardware for 1‐3/8” and 1‐3/4” thick doors.

10–Cut the MDF panel to the required length, which should be the door

width minus ¾”. Fasten it to the header track on the side of the opening sec‐

on using #10 x 1‐1/2” screws (3 per panel)

11a: Drill a 3/8” diameter hole at least 1‐1/2” deep at 3‐

1/2” from each edge of the door.

11b: Drill a 1/8” diameter hole at least 1” deep for the

fixing plates.

12‐Centre the fixing plate, flat side up, over the

pre‐drilled hole.

13‐Screw on the fixing plates using #10 x 1‐1/4” screws.

14‐Unscrew the a achment plates for the fastening

bolt. 15‐Screw the 5/16” hex nut onto the bolt.

16‐Screw the fastening

bolt into the fixing plate.

17‐Posi on the door under the hangers and insert the

fastening bolts into the a achment sleeves.

Installa on Instruc ons for UT‐5000 Series Pocket Door

Hardware for 1‐3/8” and 1‐3/4” thick doors

18‐Re‐fasten the a achment plates removed in

step 14. DO NOT OVER‐TIGHTEN.

19‐Set the door level and adjust its height by

screwing or unscrewing the hex part of the bolt.

Once adjustment is made, lock the bolt by

ghtening the 5/16” hex nut.

20‐Install the stopper UT‐5040 to mid‐height of the

stud at the back of the pocket. When the door is in

the open posi on, it will be cushioned by the stop‐

per. Depending on the type of trim used, it may be

required to shim the stopper with 3/16” washers.

21‐Slide the stopper UT‐DS100 into the rail at the desired stop point and

a ach to rail using #10 x 2” screws.

22‐Complete the installa on by installing the drywall and mouldings. These items are supplied by others.

Steel upright x4 

MDF board x1 

Header UT‐5000  

HangerUT‐1010 x2 

Fixing plate x2 

Header bracket x2 

Parts list for UT‐5000 series:

Floor bracket  x2 

HEX TEK screw #14x3/4’’ x8 

Tooth washer x4 

Offset guide UT‐1050 x2 

Center guide UT‐1055 x2 

Stop UT‐5040 x1 

Stop UT‐DS100 x2 

5/16’’ Hex nut x2 

Spacer washer x6 

Self‐drilling screw #10x1‐1/2’’ x6 

Self‐drilling screw #10x2’’ x4 

Screw #10x1‐1/4’’ x13 

Screw #8x3/4’’ x10 

Drywall screw 1’’ x25