Upload
letu
View
214
Download
0
Embed Size (px)
Citation preview
Technical Data 97479
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-029-029, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97480
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-029-046, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97481
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-029-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97482
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-029-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
28
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
ModelsLRB24-MFTLRX24-MFT Flexible Version
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 2 W
holding 1.2 WTransformer sizing 6 VA (class 2 power source)Electrical connection
LRX24-MFT
½” conduit connector18 GA, plenum rated cable3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC (default)
4 to 20 mAvariable (VDC, PWM, fl oating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA maxVDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω1500 Ω (PWM, fl oating point, on/off)
Angle of rotation 90° electronically variableadjustable with mechanical stop
Direction of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time 150 seconds (default)
Variable (35 to 150 secs)Humidity 5 to 95% RH non-condensing
(EN 60730-1)Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
LR...24-MFT Actuators, Multi-Function Technology
Dimensions
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
29
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
4Position feedback cannot be used with Triac sink controller.The actuator internal common reference is not compatible.
6Control signal may be pulsed from either the Hot (source)or the Common (sink) 24 VAC line.
8Contact closures A & B also can be triacs.A& B should both be closed for triac source and open for triac sink.
9For triac sink the common connection from the actuatormust be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-MFT Actuators, Multi-Function Technology
W53
8
On/Off control
W53
8
Floating Point
W53
8
VDC/4-20 mA
W53
8
PWM
Technical Data 97483
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-029-150, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97485
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-046-029, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97486
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-046-046, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97487
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-046-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97488
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-046-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97489
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-046-150, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97490
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-073-029, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97491
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-073-046, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97492
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-073-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97493
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-073-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97494
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-073-150, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97495
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-116-029, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97496
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-116-046, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97497
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-116-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97498
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-116-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97499
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-116-150, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97500
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-150-029, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97501
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-150-046, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97502
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-150-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97503
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-150-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
28
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
ModelsLRB24-MFTLRX24-MFT Flexible Version
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 2 W
holding 1.2 WTransformer sizing 6 VA (class 2 power source)Electrical connection
LRX24-MFT
½” conduit connector18 GA, plenum rated cable3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC (default)
4 to 20 mAvariable (VDC, PWM, fl oating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA maxVDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω1500 Ω (PWM, fl oating point, on/off)
Angle of rotation 90° electronically variableadjustable with mechanical stop
Direction of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time 150 seconds (default)
Variable (35 to 150 secs)Humidity 5 to 95% RH non-condensing
(EN 60730-1)Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
LR...24-MFT Actuators, Multi-Function Technology
Dimensions
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
29
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
4Position feedback cannot be used with Triac sink controller.The actuator internal common reference is not compatible.
6Control signal may be pulsed from either the Hot (source)or the Common (sink) 24 VAC line.
8Contact closures A & B also can be triacs.A& B should both be closed for triac source and open for triac sink.
9For triac sink the common connection from the actuatormust be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-MFT Actuators, Multi-Function Technology
W53
8
On/Off control
W53
8
Floating Point
W53
8
VDC/4-20 mA
W53
8
PWM
Technical Data 97504
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.5" [15]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B315-150-150, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 1/2", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
28
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
ModelsLRB24-MFTLRX24-MFT Flexible Version
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 2 W
holding 1.2 WTransformer sizing 6 VA (class 2 power source)Electrical connection
LRX24-MFT
½” conduit connector18 GA, plenum rated cable3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC (default)
4 to 20 mAvariable (VDC, PWM, fl oating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA maxVDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω1500 Ω (PWM, fl oating point, on/off)
Angle of rotation 90° electronically variableadjustable with mechanical stop
Direction of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time 150 seconds (default)
Variable (35 to 150 secs)Humidity 5 to 95% RH non-condensing
(EN 60730-1)Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
LR...24-MFT Actuators, Multi-Function Technology
Dimensions
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
29
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
4Position feedback cannot be used with Triac sink controller.The actuator internal common reference is not compatible.
6Control signal may be pulsed from either the Hot (source)or the Common (sink) 24 VAC line.
8Contact closures A & B also can be triacs.A& B should both be closed for triac source and open for triac sink.
9For triac sink the common connection from the actuatormust be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-MFT Actuators, Multi-Function Technology
W53
8
On/Off control
W53
8
Floating Point
W53
8
VDC/4-20 mA
W53
8
PWM
Technical Data 97508
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-073-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97514
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-116-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97507
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-116-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97513
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-186-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97512
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-186-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97506
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-186-186, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97511
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-290-073, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
28
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
ModelsLRB24-MFTLRX24-MFT Flexible Version
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 2 W
holding 1.2 WTransformer sizing 6 VA (class 2 power source)Electrical connection
LRX24-MFT
½” conduit connector18 GA, plenum rated cable3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC (default)
4 to 20 mAvariable (VDC, PWM, fl oating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA maxVDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω1500 Ω (PWM, fl oating point, on/off)
Angle of rotation 90° electronically variableadjustable with mechanical stop
Direction of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time 150 seconds (default)
Variable (35 to 150 secs)Humidity 5 to 95% RH non-condensing
(EN 60730-1)Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
LR...24-MFT Actuators, Multi-Function Technology
Dimensions
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
29
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
4Position feedback cannot be used with Triac sink controller.The actuator internal common reference is not compatible.
6Control signal may be pulsed from either the Hot (source)or the Common (sink) 24 VAC line.
8Contact closures A & B also can be triacs.A& B should both be closed for triac source and open for triac sink.
9For triac sink the common connection from the actuatormust be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-MFT Actuators, Multi-Function Technology
W53
8
On/Off control
W53
8
Floating Point
W53
8
VDC/4-20 mA
W53
8
PWM
Technical Data 97510
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-290-116, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
28
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
ModelsLRB24-MFTLRX24-MFT Flexible Version
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 2 W
holding 1.2 WTransformer sizing 6 VA (class 2 power source)Electrical connection
LRX24-MFT
½” conduit connector18 GA, plenum rated cable3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC (default)
4 to 20 mAvariable (VDC, PWM, fl oating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA maxVDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω1500 Ω (PWM, fl oating point, on/off)
Angle of rotation 90° electronically variableadjustable with mechanical stop
Direction of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time 150 seconds (default)
Variable (35 to 150 secs)Humidity 5 to 95% RH non-condensing
(EN 60730-1)Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
LR...24-MFT Actuators, Multi-Function Technology
Dimensions
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
29
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
4Position feedback cannot be used with Triac sink controller.The actuator internal common reference is not compatible.
6Control signal may be pulsed from either the Hot (source)or the Common (sink) 24 VAC line.
8Contact closures A & B also can be triacs.A& B should both be closed for triac source and open for triac sink.
9For triac sink the common connection from the actuatormust be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-MFT Actuators, Multi-Function Technology
W53
8
On/Off control
W53
8
Floating Point
W53
8
VDC/4-20 mA
W53
8
PWM
Technical Data 97509
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-290-186, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
Technical Data 97505
Service chilled or hot water, 60% glycolFlow Characteristic linearAction Sequence 1 - (0° to 30° angle)¹, Dead zone -
(30° to 60°), Sequence - 2 (60° to 90° angle)²Size - Inches [mm] 0.75" [20]End Fitting NPT female endsBall chrome plated brassStem nickel plated brassCharacterized Disc chrome plated steelBody Pressure Rating 232 psiMedia Temp Range (water) 43°F to 122°F [6°C to 50°C]Maximum Differential Pressure(Water)
15 psi for typical applications
Close-off Pressure 50 psiLeakage rate A (bubble tight) according to EN12266-1
Flow Patterns
ApplicationThe 6-way characterized control valve is ideal for chilled beams and radiant ceil-ings offering reduced wiring by using a single actuator instead of two. It elimi-nates the need for a change over valve and enables the use of a single coil forheating and cooling.
Dimensions (Inches [mm])
Application NotesThe control valve can be mounted either vertically or horizontally. Do not installthe ball valve with the stem pointing downwards.
When assembled with a 6-Way Valve the MFT actuator must be programmed forproportional control only.
Maintenance6-Way characterized control valves and rotary actuators are maintenance free.Before any kind of service work is carried out, it is essential to isolate theactuator from the power supply (by disconnecting the power).
B320-290-290, 6-Way, Characterized Control ValveChrome Plated Brass Ball and Nickel Plated Stem, 3/4", NPT female ends
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
1.7
3”
[45m
m]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.69” [43mm]
1.26” [32mm]
.87
” [2
2m
m]
.47”
[12m
m]
M4
min
. X
1.7
3”
[45
mm
]
7.97" [200]
1.69"
[42]
3.22"
[82]
2.34"
[59.4]
1.7
3”
[45
mm
]
2.99” [76mm]
1.5” [38 mm]
4.7
2”
[1
20
mm
]
1.7
3”
[45
mm
]
date
cre
ated
, 07/
02 -
Subj
ect t
o ch
ange
. © B
elim
o Ai
rcon
trols
(USA
), In
c.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
22
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
LR...24-SR Actuators, Proportional
ModelsLRB24-SR-T LRX24-SR-T w/Terminal BlockLRB24-SR LRX24-SR w/3ft. cable
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 1.5 W
holding 0.4 WTransformer sizing 3 VA (class 2 power source)Electrical connection
LRB24-SRLRX24-SR
½” conduit connector18 GA, plenum rated cable3 ft [1m]3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC, 4 to 20 mAFeedback output U 1 to 10 VDC, max 0.5 mAInput impedance 100 kΩ (0.1 mA), 500 ΩAngle of rotation 90°, adjustable with mechanical stopDirection of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time
LRB24-SRLRX24-SR
constant independent of load90 seconds150, 95, 60, 45, 35 seconds
Humidity 5 to 95% RH non-condensing (EN 60730-1)
Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001
LR...24-SR-TElectrical connection screw terminal (for 26 to 14 GA wire)
protected (NEMA 2/IP20)† Rated impulse voltage 800V, Control pollution degree 3, Type of action 1
(1.B for -S models)
Dimensions
D14
8-2W
-08
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
23
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
5 Only connect common to neg. (–) leg of control circuits.
Meets cULus or UL and CSA requirements without theneed of an electrical ground connection.The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical componentsperform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-SR Actuators, Proportional
W26
5-LR
-08
2 to 10 VDC control
W26
5-LR
-08
4 to 20 mA control
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
28
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
ModelsLRB24-MFTLRX24-MFT Flexible Version
Technical DataPower supply 24 VAC ± 20% 50/60 Hz
24 VDC ± 10%Power consumption running 2 W
holding 1.2 WTransformer sizing 6 VA (class 2 power source)Electrical connection
LRX24-MFT
½” conduit connector18 GA, plenum rated cable3 ft [1m], 10 ft [3m], 16 ft [5m]
Overload protection electronic throughout 0° to 95° rotationOperating range Y 2 to 10 VDC (default)
4 to 20 mAvariable (VDC, PWM, fl oating point, on/off)
Feedback output U 2 to 10 VDC, 0.5mA maxVDC variable
Input impedance 100 kΩ (0.1 mA), 500 Ω1500 Ω (PWM, fl oating point, on/off)
Angle of rotation 90° electronically variableadjustable with mechanical stop
Direction of rotation reversible with protectedPosition indication handleManual override external push buttonRunning time 150 seconds (default)
Variable (35 to 150 secs)Humidity 5 to 95% RH non-condensing
(EN 60730-1)Ambient temperature -22°F to 122°F [-30°C to 50°C]Storage temperature -40°F to 176°F [-40°C to 80°C]Housing NEMA 2/IP54Housing material UL94-5VAAgency listings† cULus according to UL 60730-1A/-2-14,
CAN/CSA E60730-1:02, CE according to 2004/108/EC and 2006/95/EC for line voltage and/or –S versions
Noise level <35 dB(A)Quality standard ISO 9001† Rated impulse voltage 800V, Control pollution degree 3,
Type of action 1 (1.B for -S models)
LR...24-MFT Actuators, Multi-Function Technology
Dimensions
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
29
N400
13 -
06/1
1 - S
ubje
ct to
cha
nge.
© B
elim
o Ai
rcon
trols
(USA
), In
c.
Wiring Diagrams
2 CAUTION Equipment damage!Actuators may be connected in parallel.Power consumption and input impedance must be observed.
3 Actuators may also be powered by 24 VDC.
4Position feedback cannot be used with Triac sink controller.The actuator internal common reference is not compatible.
6Control signal may be pulsed from either the Hot (source)or the Common (sink) 24 VAC line.
8Contact closures A & B also can be triacs.A& B should both be closed for triac source and open for triac sink.
9For triac sink the common connection from the actuatormust be connected to the hot connection.
The ZG-R01 500 Ω resistor converts the 4 to 20 mA control signal to2 to 10 VDC, up to 2 actuators may be connected in parallel.
WARNING Live Electrical Components!During installation, testing, servicing and troubleshooting of this product, it may
be necessary to work with live electrical components. Have a qualifi ed licensed electricianor other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.
LR...24-MFT Actuators, Multi-Function Technology
W53
8
On/Off control
W53
8
Floating Point
W53
8
VDC/4-20 mA
W53
8
PWM