RoadStar seriesGPLM

4 1 /

4" (1

14 m

m)

13 1 /

4" (3

37 m

m)

13 3 /

4" (3

49 m

m)

4 7 /

8" (1

24 m

m)

29 3/4" (756 mm) 45 1/8" (1146 mm)

EPA: 1.10 sq. ft.Weight: 31 lbs (14.1 kg)

GPLM

4 1 /

4" (1

14 m

m)

13 1 /

4" (3

37 m

m)

13 3 /

4" (3

49 m

m)

4 7 /

8" (1

24 m

m)

29 3/4" (756 mm) 45 1/8" (1146 mm)

Specifications subject to change without notice.

Includes surge protector 10kV

347 and 480 volt for 180W98LED4K only

Luminaire options

Voltage

Finishes

Luminaire accessory

GPLM

Luminaire Lamp Optical System Voltage Options Accessory Finish

Project name Type

Date Prepared by

120 208 240 277 347 480

BL Bubble levelCDMG* Dynadimmer control

DMG* 0-10 volt dimming ready power supply

PH8 Photoelectric cell, twist type includes receptaclePH8XL* Photoelectric cell, twist-lock type, ‘’Fail ON’’,

extended life – 10-year limited warranty from supplier

RC Receptacle for twist-lock photoelectric cell or shorting cap

WPG Without protective grid* Not available with 347 and 480 volt.

WH White GY3 Medium GrayBK Black NP Aluminum

NF No finish

SPC* StarSense Photo-cell Control* Luminaire option RC is required with this accessory

LampComposed of high performance white LEDs. Color temperature of 4000 Kelvin nominal, 70 CRI. Ambient operating temperature range -40C (40F) - 50C (122F). L70 lifetime of 70000 hours at 25C ambient. Use of a metal core board insures greater heat transfer and longer lifespan of the light engine.

Optical systemComposed of high performance collimators, optimized with varying acrylic beam angles to achieve desired distribution. System is rated IP66. Performance shall be tested per LM63 and LM79 (IESNA) certifying its photometric performance. Dark sky compliant.

Surge protectorLED Driver 3 poles surge protectors and protect line-ground, line-neutral, and neutral-ground in accordance with IEEE / ANSI C62.41.2 guidelines. Surge rating 10kV.

DriverHigh power factor of 99%. electronic driver, operating rang 50-60 Hz. Auto-adjusting to a voltage between 120v and 277 volt AC, Class II, THD of 20%. Lamp starting capacity -40F (40C) degrees. Certified in compliance to UL requirement. Weather tightness rating IP66. Assembled on a unitized removable tray with Tyco quick disconnect plug located in a separate enclosure in order to protect from heat generated by the LEDs.

The current supplying the LEDs will be reduced by the driver when a temperature is exceeded as a protection to the LEDs and the electrical components. Output is protected from short circuits, voltage overload and current overload. Automatic recovery after correction.

HousingThe upper and lower part of the housing are made of die cast A360 Aluminum alloy 0.100 (2.5mm) minimum thickness. The mounting means includes two brackets made of stamped galvanized steel (12ga.). Fits on a 1.9” (48mm) to 2 3/8” (60mm) OD by 7” (178mm) long tenon, fixed by 1/2 13 UNC steel zinc plated bolts. An integral part of the housing permits and adjustment of +/ 5o. The housing is complete with a secured access door avoiding accidental dropping, a ground lug and a terminal block that accepts (#8 max.) wires from the primary circuit.

Heat sinkBuilt in the upper housing, optimizing the LEDs efficiency and life.

Product does not use any cooling device with moving parts (passive cooling device).

Bird guardPrevents birds from entering the luminaire. Made of high density polyethylene 0.030 (0.8mm) thick and captive to the housing.

Light engineLifeLED composed of 4 main components: LED lamp / optical system / heat sink / driver electrical components are RoHS compliant.

WiringLuminaire wiring is done using a terminal block located inside the housing.

HardwareAll exposed screws shall be stainless steel with Ceramic primer-seal base coat to reduce seizing of the parts. All seals and sealing devices are made and/or lined with EPDM and/or silicone.

FinishApplication of a polyester powder coat paint. (4 mils/100 microns). The chemical composition provides a highly durable UV and salt spray resistant finish in accordance to the ASTM-B117-73 standard and humidity proof in accordance to the ASTM-D2247-68 standard. The specially formulated Lumital powder coat finish is available in white, black, gray and bare. Additional colors are available. Consult factory for complete specifications.

Vibration resistanceMeets the ANSI C136.31-2001 table 2, American National Standard for Roadway Luminaire Vibration specifications for Bridge/overpass applications.

CertificationCSA, UL or CUL. ISO 9001-2008.

RoadStar GPLM SpecSheet 05/14 page 2 of 2

© 2014 Koninklijke Philips N.V. All rights reserved. Specifications are subject to change without notice.www.philips.com/luminaires

Philips LightingNorth America Corporation200 Franklin Square Drive Somerset, NJ 08873Phone: 855-486-2216

Philips Lighting Company281 Hillmount Road Markham ON, Canada L6C 2S3Phone: 800-668-9008