3RH - Contactor Relays

8/13/2019 3RH - Contactor Relays

1/13

3RH Contactor Relays

3RH2 contactor relays, 4- and 8-pole

3/58 SIRIUS Innovations Supplement 2010

Overview

Contactor relays and coupling relaysSize S00 with accessories

Contactor relayCoupling relay for auxiliary circuitsSolid-state timing relay block1-pole auxiliary switch block, cable entry from above2-pole auxiliary switch block, cable entry from above

1-pole auxiliary switch block, cable entry from below2-pole auxiliary switch block, cable entry from below4-pole auxiliary switch block(terminal designations according to EN 50011 or EN 50005)2-pole auxiliary switch block, solid-state compatible versionTerminal designations according to EN 50005Solder pin adapter for contactor relays with 4-pole auxiliary switch blockSolder pin adapter for contactor relays and coupling relaysAdditional load module for increasing the permissible residual currentSurge suppressor with LEDSurge suppressor without LED

3

4

5

6

7

8

9

10

11

14

12

13

1

2

10

11

11

N S B 0

_ 0 2 0 5 8

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Siemens AG 2010


2/13



3/59SIRIUS Innovations Supplement 2010

AC and DC operation

IEC 60947, EN 60947.

The 3RH2 contactor relays have screw, ring lug terminal orspring-type terminals. Four contacts are available in the basicunit.

The 3RH2 contactor relays are suitable for use in any climate.They are finger-safe according to EN 50274. The devices withring lug terminal connection comply with degree of protectionIP20 when fitted with the related terminal cover.

Contact reliability

High contact stability at low voltages and currents, suitable forsolid-state circuits with currents 1 mA at a voltage of 17 V.

Surge suppression

RC elements, varistors, diodes or diode assemblies (combina-tion of a diode and a Zener diode) can be plugged onto all con-tactor relays from the front for damping opening surges in thecoil. The plug-in direction is determined by a coding device.

Note:The OFF-delay of the NO contact and the ON-delay of theNC contact are increased if the contactor coils are attenuatedagainst voltage peaks (noise suppression diode 6 to 10 times;diode assemblies 2 to 6 times, varistor +2 to 5 ms).

Auxiliary switch blocks

The 3RH2 contactor relays can be expanded by up to fourcontacts by the addition of snap-on auxiliary switch blocks.

The auxiliary switch block can easily be snapped onto the frontof the contactors. The auxiliary switch block has a centrally po-sitioned release lever for disassembly.

The contactor relays with 4 contacts according to EN 50011,with the identification number 40E, can be extended with 80E to44E auxiliary switch blocks to obtain contactor relays with8 contacts according to EN 50011. The identification numbers80E to 44E on the auxiliary switch blocks apply to the completecontactors. These auxiliary switch blocks (3RH29 111GA..)cannot be combined with contactor relays with identificationnumbers 31E and 22E; they are coded.

All contactor relays with 4 contacts according to EN 50011, iden-tification numbers 40E to 22E, can be extended with auxiliaryswitch blocks 40 to 02 to obtain contactor relays with 6 or 8 con-tacts in accordance with EN 50005. The identification numberson the auxiliary switch blocks apply only to the attached auxiliaryswitch blocks.

In addition, fully mounted 3RH22 8-pole contactor relays areavailable; the mounted 4-pole auxiliary switch block in the 2ndtier is not removable. The terminal designations are according toEN 50011.

These versions are built according to special Swiss regulationsSUVA and are distinguished externally by a red labeling plate.

Of the auxiliary contacts (integrated plus mountable) possibleon the device, no more than four NC contacts are permitted.

Order No. scheme

Note:

The Order No. scheme is presented here merely for informationpurposes and for better understanding of the logic behind theorder numbers.

For your orders, please use the order numbers quote in thecatalog in the Selection and ordering data.

Hilfsschtze DIN EN50 005,8 oder 6 Kontakte

N S B 0

_ 0 2 1 0 5

Ident. No. 31E, 22EIdent. No. 40E

Ident. No. 80E,71E, 62E, 53E, 44E

Aux. switch blocks,

EN 50 011,4 contacts

Ident. No. 40, 31,22, 20, 11, 02

Aux. switch blocks,

EN 50 005,4 or 2 contacts

Ident. No. 80E,71E, 62E, 53E, 44E

Contactor relay,EN 50 0118 contacts

Contactor relay,EN 50 005,8 or 6 contacts

Contactor relay, EN 50 011,4 contacts

Digit of the Order No. 1st -3rd

4th 5th 6th 7th 8th 9th 10th 11th 12th

13th 14th 15th 16th

@@@ @ @ @ @ @ @ @ @ @ @ @ @ @

SIRIUS contactor relays 3 R H

2nd generation 2Device type (e. g. 1 = 4-pole contactor relay, 3 = 8-pole contactor relay) @

Number of NO contacts (e. g. 2 = 2 NO) @

Number of NC contacts (e. g. 2 = 2 NC) @

Connection type (1 = screw, 2 = spring, 4 = ring lug) @

Operating range / solenoid coil circuit (e. g. A = AC standard / without) @

Rated control supply voltage (e. g. K6 = 110/120 V, 50/60 Hz ) @ @

No significance @

Special version @ @ @ @

Example 3 R H 2 1 2 2 1 A K 6 0

Siemens AG 2010


3/13



3/60 SIRIUS Innovations Supplement 2010 Illustrations are approximate

Selection and ordering data

AC operation

For other voltages see page 3/62.

For accessories see pages 3/93 to 3/97.

1) The 3RH21 contactor relays are also available with ring lug terminal con-nection. Please insert the number "4" into the 8 th position of the part num-ber for versions with ring lug terminal connection.

2) Coil operating rangeat 50 Hz: 0.8 to 1.1 x U sat 60 Hz: 0.85 to 1.1 x U s .

3) For AC-15/AC-14 the following applies: I e = 6 A for mounted auxiliarycontacts.

Size S00

3RH21 . .-1. . . . 3RH21 . .-2. . . . 3RH22 . .-1. . . . 3RH22 . . -2 . . . .

Rated opera-tional currentat 240 V

Contacts Rated control supplyvoltage U sat 50/60 Hz 2)

Screw terminals 1) Weightapprox.

Spring-typeterminals

Weightapprox.Ident.

No.Version

Order No. Order No.

A NO NC V AC kg kg

For screw and snap-on mounting onto TH 35 standard mounting railTerminal designations according to EN 500114 NO, identification number 40E 3 NO + 1 E, identification number 31E 2 NO + 2 NE, identification number 22E

10 40E 4 -- 24 3RH21 40-1AB00 0.220 3RH21 40-2AB00 0.240110/120 3RH21 40-1AK60 0.220 3RH21 40-2AK60 0.240220/240 3RH21 40-1AP60 0.220 3RH21 40-2AP60 0.240

31E 3 1 24 3RH21 31-1AB00 0.220 3RH21 31-2AB00 0.240110/120 3RH21 31-1AK60 0.220 3RH21 31-2AK60 0.240220/240 3RH21 31-1AP60 0.220 3RH21 31-2AP60 0.240

22E 2 2 24 3RH21 22-1AB00 0.220 3RH21 22-2AB00 0.240110/120 3RH21 22-1AK60 0.220 3RH21 22-2AK60 0.240220/240 3RH21 22-1AP60 0.220 3RH21 22-2AP60 0.240

With permanently mounted auxiliary switch block 4 NO + 4 NC, identification number 44E 6 NO + 2 NC, identification number 62E

10 3) 44E 4 4 110/120 3RH22 44-1AK60 0.270 3RH22 44-2AK60 0.30062E 6 2 110/120 3RH22 62-1AK60 0.270 3RH22 62-2AK60 0.300

Siemens AG 2010


4/13



3/61SIRIUS Innovations Supplement 2010Illustrations are approximate

DC operation DC solenoid system



1) The 3RH21 contactor relays are also available with ring lug terminalconnection. Please insert the number "4" into the 8 th position of the partnumber for versions with ring lug terminal connection.

2) For AC-15/AC-14 the following applies: I e = 6 A for mounted auxiliarycontacts.

Size S00

3RH21 . .-1. . . . 3RH21 . . -2. . . . 3RH22 . .-1. . . . 3RH22 . . -2. . . .

Rated operationalcurrent I e /AC-15/AC-14at 240 V

Contacts Rated control supplyvoltage U s

Screw terminals 1) Weightapprox.

Spring-typeterminals

Weightapprox.Ident.

No.Version

Order No. Order No.

A NO NC V DC kg kg

For screw and snap-on mounting onto TH 35 standard mounting railTerminal designations according to EN 500114 NO, identification number 40E 3 NO + 1 E, identification number 31E 2 NO + 2 NE, identification number 22E

10 40E 4 -- 24 3RH21 40-1BB40 0.280 3RH21 40-2BB40 0.300110 3RH21 40-1BF40 0.280 3RH21 40-2BF40 0.300

31E 3 1 24 3RH21 31-1BB40 0.280 3RH21 31-2BB40 0.300110 3RH21 31-1BF40 0.280 3RH21 31-2BF40 0.300

22E 2 2 24 3RH21 22-1BB40 0.280 3RH21 22-2BB40 0.300110 3RH21 22-1BF40 0.280 3RH21 22-2BF40 0.300

With permanently mounted auxiliary switch block 4 NO + 4 NC, identification number 44E 6 NO + 2 NC, identification number 62E

10 2) 44E 4 4 24 3RH22 44-1BB40 0.330 3RH22 44-2BB40 0.35062E 6 2 24 3RH22 62-1BB40 0.330 3RH22 62-2BB40 0.350

Siemens AG 2010


5/13


6/13




More information

1) I e = 6 A at AC-14/AC-15.

Contactor Type 3RH2Size S00Width mm 45

Permissible mounting positionThe contactors are designed for opera-tion on a vertical mounting surface.

Upright mounting position

Special version required(for coupling relays and contactor relays with extended operating range3RH21 22-2K.40, please ask)

Positively-driven operation of contacts in contactor relays3RH2: Explanations:Yes, in the basic unit and the auxiliary switch block as well as betweenthe basic unit and the snap-on auxiliary switch b lock (removable) acc. to: ZH 1/457 EN 60947-5-1, Appendix L

There is positively-driven operation if it is ensured that the NC and NOcontacts cannot be closed at the same time.

ZH1/457Safety Rules for Controls on Power-Operated Metalworking Presses.

EN 60947-5-1, Appendix LLow-Voltage Controlgear, Controls and Contact Blocks. Special requirementsfor positively-driven contacts

3RH22:Yes, in the basic unit and the auxiliary switch block as well as betweenthe basic unit and the snap-on auxiliary switch block (permanentlymounted) acc. to: ZH 1/457 EN 60947-5-1, Appendix LNote:3RH29 11-. NF.solid-state compatible auxiliary switch blocks have nopositively-driven contacts.Contact reliabilityContact reliability at 17 V, 1 mA acc. to EN 60947-5-4 Frequency of contact faults


7/13


8/13




1) The 3RT29 16-1GA00 additional load module is recommendedfor higher residual currents (see page 3/101) .

2) The OFF-delay of the NO contact and the ON-delay of the NC contact areincreased if the contactor coils are attentuated against voltage peaks(noise suppression diode 6 to 10 times; diode assemblies 2 to 6 times,varistor +2 to 5 ms).

Contactors Type 3RH2.Size S00Width mm 45

ControlSolenoid coil operating range

AC operation At 50 Hz 0.8 ... 1.1 x U sAt 60 Hz 0.85 ... 1.1 x U s DC operation At +50 C 0.8 ... 1.1 x U s

At +60 C 0.85 ... 1.1 x U sPower consumption of the solenoid coils(when coil is cold and 1.0 x U s) AC operation, 50 Hz - Closing VA/p.f. 37/0.8

- Closed VA/p.f. 5.7/0.25 AC operation, 60 Hz - Closing VA/p.f. 33/0.75

- Closed VA/p.f. 4.4/0.25 DC operation - Closing = Closed W 4.0Permissible residual current of the electronics(with 0 signal)

For AC operation 1) < 4 mA x (230 V/ U s) For DC operation < 10 mA x (24 V/ U s)

Operating times 2)(Total break time = OFF-delay + Arcing time)AC operation Values apply with coil in cold state

and at operating temperature foroperating range

Closing

- ON-delay of NO contact 0.8 ... 1.1 x U s ms 8 ... 331.0 x U s ms 9 ... 223RH24 minimum operating time ms 35

- OFF-delay of NC contact 0.8 ... 1.1 x U s ms 6 ... 251.0 x U s ms 6.5 ... 19

Opening- OFF-delay of NO contact 0.8 ... 1.1 x U s ms 4 ... 15

1.0 x U s ms 4.5 ... 153RH24 minimum operating time ms 30

- ON-delay of NC contact 0.8 ... 1.1 x U s ms 5 ... 151.0 x U s ms 5 ... 15

DC operation Closing

- ON-delay of NO contact 0.8 ... 1.1 x U s ms 30 ... 1001.0 x U s ms 35 ... 503RH24 minimum operating time ms 100

- OFF-delay of NC contact 0.8 ... 1.1 x U s ms 25 ... 901.0 x U s ms 30 ... 45

Opening- OFF-delay of NO contact 0.8 ... 1.1 x U s ms 7 ... 13

1.0 x U s ms 7 ... 123RH24 minimum operating time ms 30

- ON-delay of NC contact 0.8 ... 1.1 x U s ms 13 ... 191.0 x U s ms 13 ... 18

Arcing time ms 10 ... 15Dependence of the switching frequency z 'on the operational current I ' and operational voltage U ':z ' = z I e / I ' (U e / U ')

1.5 1/h

Siemens AG 2010


9/13



3/66 SIRIUS Innovations Supplement 2010

1) Attachable auxiliary switch: I e = 6A for AC-15/AC-14.

Contactors Type 3RH2.Size S00Width mm 45

Load sideRated operational currents I e

AC-12 A 10 1)AC-15/AC-14For rated operational voltage U s

Up to 230 V A 10 1)400 V A 3500 V A 2690 V A 1

DC-12For rated operational voltage U s 1 conducting path 24 V A 6

60 V A 6110 V A 3220 V A 1440 V A 0.3600 V A 0.15

2 conducting paths in series 24 V A 1060 V A 10

110 V A 4220 V A 2440 V A 1.3

600 V A 0.65 3 conducting paths in series 24 V A 10

60 V A 10110 V A 10220 V A 3.6440 V A 2.5600 V A 1.8

DC-13For rated operational voltage U s 1 conducting path 24 V A 6

60 V A 2110 V A 1220 V A 0.3440 V A 0.14600 V A 0.1

2 conducting paths in series 24 V A 1060 V A 3.5

110 V A 1.3

220 V A 0.9440 V A 0.2600 V A 0.1

3 conducting paths in series 24 V A 1060 V A 4.7

110 V A 3220 V A 1.2440 V A 0.5600 V A 0.26

Switching frequency z In operating cycles/h

during rated operationfor utilization category

AC-12/DC-12 h -1 1000AC-15/AC-14 h -1 1000

DC-13 h -1 1000 No-load switching frequency h -1 10000

Dependence of the switching frequency z ' onthe operational current I ' and operational voltage U ':z ' = z I e / I ' (U e / U ')

1.5 1/h

s and u rated dataBasic units and auxiliary switch blocks Rated control supply voltage V AC Max. 600 Rated voltage V AC 600 Switching capacity A 600, Q 600 Uninterrupted current at 240 V AC A 10

Siemens AG 2010


10/13

3RH Control, Coupling Relays

3RH24 latched control relays, 4-pole


Overview

AC and DC operation

IEC 60947, EN 60947.

The terminal designations comply with EN 50011.

The contactor coil and the coil of the release solenoid are bothdesigned for uninterrupted duty.

The number of auxiliary contacts can be extended by means offront auxiliary switch blocks (up to 4 poles).

RC elements, varistors diodes or diode assemblies can be fittedto both coils from the front for damping opening surges in thecoil.

The control relay can also be switched on and releasedmanually (for minimum actuating times, see TechnicalSpecifications on page 3/65) .




Note:For ring lug terminal versions, replace the 8 th digit with thenumber "4".

1) Coil operating rangeat 50 Hz: 0.8 to 1.1 x U sat 60 Hz: 0.85 to 1.1 U s .

3RH24 ..-1....Rated operationalcurrent I e /AC-15/AC-14at 240 V

Contacts Rated control supplyvoltage U s

Screw terminals Weightapprox.Ident. No. acc. to

EN 50011Version

Order No.

A NO NC V kg

With screw terminals For screw and snap-on mounting onto TH 35 standard mounting railTerminal designations according to EN 500114 NO, identificationnumber 40E

3 NO + 1 E , identification number 31E 2 NO + 2 NE, identification number22E

AC operation AC 50/60 Hz 1)

10 40 E 4 -- 24 3RH24 40-1AB00 0.380110/120 3RH24 40-1AK60 0.380220/240 3RH24 40-1AP60 0.380

31 E 3 1 24 3RH24 31-1AB00 0.380110/120 3RH24 31-1AK60 0.380220/240 3RH24 31-1AP60 0.380

22 E 2 2 24 3RH24 22-1AB00 0.380110/120 3RH24 22-1AK60 0.380220/240 3RH24 22-1AP60 0.380

DC operation DC solenoid system DC

10 40 E 4 -- 24 3RH24 40-1BB40 0.500110 3RH24 40-1BF40 0.500125 3RH24 40-1BG40 0.500

31 E 3 1 24 3RH24 31-1BB40 0.500110 3RH24 31-1BF40 0.500125 3RH24 31-1BG40 0.500

22 E 2 2 24 3RH24 22-1BB40 0.500110 3RH24 22-1BF40 0.500125 3RH24 22-1BG40 0.500

Siemens AG 2010


11/13


3RH21 coupling relays for switchingauxiliary circuits, 4-pole

3/68 SIRIUS Innovations Supplement 2010 Illustrations are approximate

Application

DC operation

IEC 60947, EN 60947.

The 3RH21 coupling relays for switching auxiliary circuits are

tailored to the special requirements of working with electroniccontrols.

The 3RH21 coupling relays cannot be extended with auxiliaryswitch blocks.

Coupling relays have a low power consumption and anextended solenoid coil operating range.

Depending on the version, the solenoid coils are supplied eitherwithout overvoltage damping (versions 3RH21 ..-.HB40 or3RH21 .. -. MB40-0KT0) or with a diode or suppressor diodeconnected as standard.


DC operationLow power consumptionExtended operating range of the solenoid coilIntegrated coil circuit

For surge suppressors see page 3/100.


3RH21 . . -1.B40 3RH21 . .-2.B40


Auxiliary contacts Screw terminals Weightapprox.

Spring-type terminals Weightapprox.Ident. No. acc. to

EN 50011Version

Order No. Order No.

A NO NC kg kg

For screw and snap-on mounting onto TH 35 standard mounting railSize S00

Diode, varistor or RC element, attachableTerminal designations according to EN 50011 (no auxiliary switch blocks can be attached)4 NO, identificationnumber 40E

3 NO + 1 NC, identification number31E

2 NO + 2 NC, identification number 22E

Rated control supply voltage U s = 24 V DC, operating range 0.7 to 1.25 x U sPower consumption of the coils 2.8 W at 24 V10 40E 4 -- 3RH21 40-1HB40 0.280 3RH21 40-2HB40 0.300

31E 3 1 3RH21 31-1HB40 0.280 3RH21 31-2HB40 0.30022E 2 2 3RH21 22-1HB40 0.280 3RH21 22-2HB40 0.300

Rated control supply voltage U s = 24 V DC, operating range 0.85 to 1.85 x U sPower consumption of the coils 1.6 W at 24 V10 40E 4 -- 3RH21 40-1MB40-0KT0 0.280 3RH21 40-2MB40-0KT0 0.300

31E 3 1 3RH21 31-1MB40-0KT0 0.280 3RH21 31-2MB40-0KT0 0.300

22E 2 2 3RH21 22-1MB40-0KT0 0.280 3RH21 22-2MB40-0KT0 0.300

Siemens AG 2010


12/13





3RH21 . . -1.B40 3RH21 . .-2.B40


Auxiliary contacts Screw terminals Weightapprox.

Spring-type terminals Weightapprox.Ident. No. acc. to

EN 50011Version

Order No. Order No.

A NO NC kg kg

For screw and snap-on mounting onto TH 35 standard mounting railSize S00 With integrated coil circuit (diode)Terminal designations according to EN 50011 (no auxiliary switch blocks can be attached)4 NO, identification number 40E 3 NO + 1 NC, identification number 31E 2 NO + 2 NC, identification number 22E

Rated control supply voltage U s = 24 V DC, operating range 0.7 to 1.25 x U sPower consumption of the coils 2.8 W at 24 V10 40E 4 -- 3RH21 40-1JB40 0.280 3RH21 40-2JB40 0.300

31E 3 1 3RH21 31-1JB40 0.280 3RH21 31-2JB40 0.30022E 2 2 3RH21 22-1JB40 0.280 3RH21 22-2JB40 0.300

Rated control supply voltage U s = 24 V DC, operating range 0.85 to 1.85 x U sPower consumption of the coils 1.6 W at 24 V10 40E 4 -- 3RH21 40-1VB40 0.280 3RH21 40-2VB40 0.300

31E 3 1 3RH21 31-1VB40 0.280 3RH21 31-2VB40 0.30022E 2 2 3RH21 22-1VB40 0.280 3RH21 22-2VB40 0.300

With integrated coil circuit (suppressor diode)

Terminal designations according to EN 50011 (no auxiliary switch blocks can be attached)4 NO, identification number 40E 3 NO + 1 NC, identification number 31E 2 NO + 2 NC, identification number 22E

Rated control supply voltage U s = 24 V DC, operating range 0.7 to 1.25 x U sPower consumption of the coils 2.8 W at 24 V10 40E 4 -- 3RH21 40-1KB40 0.280 3RH21 40-2KB40 0.300

31E 3 1 3RH21 31-1KB40 0.280 3RH21 31-2KB40 0.30022E 2 2 3RH21 22-1KB40 0.280 3RH21 22-2KB40 0.300

Rated control supply voltage U s = 24 V DC, operating range 0.85 to 1.85 x U sPower consumption of the coils 1.6 W at 24 V10 40E 4 -- 3RH21 40-1SB40 0.280 3RH21 40-2SB40 0.300

31E 3 1 3RH21 31-1SB40 0.280 3RH21 31-2SB40 0.30022E 2 2 3RH21 22-1SB40 0.280 3RH21 22-2SB40 0.300

A1(+)

A2()14

13

24

23

34

33

44

43 A1(+)

A2()14

13

22 34

33

44

4321 A1(+)

A2()14

13

44

43

32

31

22

21

Siemens AG 2010


13/13



More informationAll technical specifications not mentioned in the table below are identical to those of the 3RH21 contactor relays (see page 3/63).The size S00 coupling relays (3RH21) cannot be extended with auxiliary switch blocks.

Contactor type 3RH21 . .- .HB40 3RH21 . .-.JB40 3RH21 ..-.KB40Size S00 S00 S00

Width mm 45 45 45Solenoid coil operating range 0.7 ... 1.25 x U sPower consumption of the solenoid coil (for coldcoil)Closing = Closed At U s = 17 V W 1.4 At U s = 24 V W 2.8 At U s = 30 V W 4.4Permissible residual currentof the electronics for 0 signal

< 10 mA x (24 V/ U s)

Overvoltage configuration of the solenoid coil Without overvoltage damping With diode With suppressor diode

Operating times Closing at 17 V

- ON-delay NO ms 40 ... 130- OFF-delay NC ms 30 ... 80

At 24 V- ON-delay NO ms 35 ... 60- OFF-delay NC ms 25 ... 40

At 30 V- ON-delay NO ms 25 ... 50- OFF-delay NC ms 15 ... 30

Closing at 17 ... 30 V- OFF-delay NO ms 7 ... 20 38 ... 65 7 ... 20- ON-delay NC ms 20 ... 30 55 ... 75 20 ... 30

Upright mounting position Request required

Contactor type 3RH21 . .- .MB40-0KT0 3RH21 . .-.VB40 3RH21 ..-.WB40Size S00 S00 S00

Width mm 45 45 45Solenoid coil operating range 0.85 ... 1.85 x U sPower consumption of the solenoid coil (for cold coil)Closing = Closed at U s = 24 V

W 1.6

Permissible residual currentof the electronics for 0 signal

< 8 mA x (24 V/ U s )

Overvoltage configuration of the solenoid coil Diode, varistor or RC element,attachable

Built-in diode Built-in suppressor diode

Operating times of the coupling relays Closing at 20.5 V


At 24 V

- ON-delay NO ms 25 ... 90- OFF-delay NC ms 15 ... 80 At 44 V


Closing at 17 ... 30 V- OFF-delay NO ms 5 ... 20 20 ... 80 5 ... 20- ON-delay NC ms 10 ... 30 30 ... 90 10 ... 30

Upright mounting position Request required

Siemens AG 2010

Documents

3RH - Contactor Relays