3KC18037ABABTQZZA_V1_Alcatel-Lucent 1646 Synchronous Multiplexer Compact Release 2.1 Installation and System Turn-Up Guide

Title page

Alcatel-Lucent

1646 SMC | Release 2.1

Installation and System Turn-Up Guide

3KC18037ABABTQZZA

Issue 2

December 2011

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements


Legal notice

Legal notice

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective

owners.

The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.

Copyright © 2011 Alcatel-Lucent. All rights reserved.

Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside

Alcatel-Lucent without its written authorization.

Not to be used or disclosed except in accordance with applicable agreements.

Notice

The information in this document is subject to change without notice. Although every effort has been made to make this document as accurate, complete, and

clear as possible, Alcatel-Lucent and its predecessors assume no responsibility for any errors that appear in this document.

Federal Communications Commission (FCC) Notification and Repair Information

This equipment is designed to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, causes interference to radio communications.

Operation of this equipment in a residence is likely to cause harmful interference, in which case, the users are required to correct the interference at their own

expense.

Security statement

In rare instances, unauthorized individuals make connections to the telecommunications network. In such an event, applicable tariffs require that the

customer pay all network charges for traffic. Alcatel-Lucent and its predecessors cannot be responsible for such charges and will not make any allowance or

give any credit for charges that result from unauthorized access.

Limited warranty

Alcatel-Lucent provides a limited warranty for this product. For more information, consult your local Alcatel-Lucent customer support team.

Ordering information

To order more copies of this document or other Alcatel-Lucent documents, please access the Online Customer Support (OLCS) (https://support.lucent.com).

Information product support

To comment on this information product, go to the Online Comment Form (http://www.alcatel-lucent-info.com/comments/enus/) or email your comments to

the Comments Hotline ([email protected]).




https://support.lucent.com

Contents

About this document

Purpose ............................................................................................................................................................................................. ixix

Intended audience ......................................................................................................................................................................... ixix

How to use this document ......................................................................................................................................................... ixix

Safety information ......................................................................................................................................................................... xx

Related information ....................................................................................................................................................................... xx

Technical support .......................................................................................................................................................................... xixi

How to order ................................................................................................................................................................................... xixi

How to comment ........................................................................................................................................................................... xixi

1 Safety

Overview ...................................................................................................................................................................................... 1-11-1

Structure of safety statements ............................................................................................................................................... 1-21-2

Laser product classification ................................................................................................................................................... 1-41-4

Laser safety ................................................................................................................................................................................. 1-61-6

Electrostatic discharge ESD considerations .................................................................................................................... 1-91-9

General safety .......................................................................................................................................................................... 1-141-14

2 Installation tools

Overview ...................................................................................................................................................................................... 2-12-1

List of installation tools .......................................................................................................................................................... 2-22-2

Special tools and test equipment ......................................................................................................................................... 2-42-4

Method of procedure ............................................................................................................................................................... 2-52-5

....................................................................................................................................................................................................................................

1646 SMC

3KC18037ABABTQZZA Release 2.1

Issue 2 December 2011



iii

3 Physical installation

Overview ...................................................................................................................................................................................... 3-13-1

Caution to avoid Equipment damage ................................................................................................................................. 3-23-2

Unpack and inspect equipment ............................................................................................................................................ 3-43-4

Preparation .................................................................................................................................................................................. 3-63-6

4 Power, cable, and fiber installation

Overview ...................................................................................................................................................................................... 4-14-1

Install ground and power cables .......................................................................................................................................... 4-24-2

Power cable installation .......................................................................................................................................................... 4-54-5

Connect management and alarm cables ............................................................................................................................ 4-64-6

Signal transmission cables ..................................................................................................................................................... 4-84-8

5 System turn-up and testing

Overview ...................................................................................................................................................................................... 5-15-1

Requirements .............................................................................................................................................................................. 5-25-2

NE turn-up and testing ............................................................................................................................................................ 5-35-3

Software upgrade using ZIC ............................................................................................................................................... 5-115-11

Troubleshooting ...................................................................................................................................................................... 5-175-17

A Miscellaneous references

Overview ..................................................................................................................................................................................... A-1A-1

Fiber optic cleaning ................................................................................................................................................................. A-2A-2

Cables, connectors, and assemblies .................................................................................................................................. A-6A-6

Cable assembling instruction ............................................................................................................................................ A-19A-19

Install FTP server .................................................................................................................................................................. A-24A-24

List of SFPs ............................................................................................................................................................................. A-30A-30

Glossary

Index

Contents

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

iv Alcatel-Lucent – Proprietary


1646 SMC



List of tables

1-1 Laser classes ................................................................................................................................................................ 1-51-5

5-1 List of possible issues and actions .................................................................................................................... 5-175-17

A-1 RJ-45 connector pin assignment and cable ..................................................................................................... A-7A-7

A-2 List of SFPs .............................................................................................................................................................. A-30A-30

....................................................................................................................................................................................................................................

1646 SMC





v

List of tables

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

vi Alcatel-Lucent – Proprietary


1646 SMC



List of figures

1-1 Laser warning label ................................................................................................................................................... 1-71-7

1-2 Static control wrist strap ....................................................................................................................................... 1-101-10

1-3 Correct operations for card insertion ............................................................................................................... 1-141-14

1-4 Card alignment ......................................................................................................................................................... 1-151-15

4-1 AC power connector ................................................................................................................................................. 4-34-3

4-2 DC power connector ................................................................................................................................................. 4-44-4

4-3 E1 cables .................................................................................................................................................................... 4-104-10

5-1 ZIC-FC-Launcher ...................................................................................................................................................... 5-45-4

5-2 Add Network Element ............................................................................................................................................. 5-55-5

5-3 NE Check ...................................................................................................................................................................... 5-65-6

5-4 Connect to NE ............................................................................................................................................................. 5-75-7

5-5 ZIC authentication window ................................................................................................................................... 5-85-8

5-6 ZIC main window ...................................................................................................................................................... 5-95-9

5-7 Software upgrade ..................................................................................................................................................... 5-115-11

5-8 Parameters in Remote File tab ............................................................................................................................ 5-125-12

5-9 Confirm software upgrade ................................................................................................................................... 5-135-13

5-10 Software upgrade confirmed ............................................................................................................................... 5-135-13

5-11 Software upgrade status ........................................................................................................................................ 5-145-14

5-12 Software upgrade complete ................................................................................................................................. 5-155-15

5-13 System information ................................................................................................................................................ 5-165-16

5-14 System information details .................................................................................................................................. 5-165-16

5-15 Configure serial port .............................................................................................................................................. 5-195-19

....................................................................................................................................................................................................................................

1646 SMC





vii

5-16 Start-up information ............................................................................................................................................... 5-205-20

A-1 Fiber-optic connector inspection ......................................................................................................................... A-4A-4

A-2 RJ-45 connector front view, including SYNC/EOW, F2/DBG, HK, LAN, FE1~4 and FE 5~8

............................................................................................................................................................................... A-7A-7A-7

A-3 RJ-45 connector ....................................................................................................................................................... A-7A-7

A-4 E1/T1 connector ANEA96 front view .............................................................................................................. A-9A-9

A-5 Crimp ferrule ........................................................................................................................................................... A-19A-19

A-6 Crimp tool ................................................................................................................................................................. A-20A-20

A-7 Dimensions of cable stripping ........................................................................................................................... A-21A-21

List of figures

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

viii Alcatel-Lucent – Proprietary


1646 SMC



About this documentAbout this document

Purpose

The Alcatel-Lucent 1646 SMC Installation and System Turn-Up Guide provides

installation and testing instructions. This manual is not a service manual.

Intended audience

This manual is intended for individuals who are responsible for the installation,

acceptance, operations, and maintenance of the Alcatel-Lucent 1646 SMC.

How to use this document

This manual is divided into several chapters and appendices. The first chapter contains

safety information and general installation information. The other chapters provide

instructional steps for personnel needing additional detail or background information.

Assumptions

This document assumes that users have an understanding of the following:

• Basic principles of telecommunication transmission

• Common telecommunication and system terminology (a glossary is provided in this

document to assist you)

• Test sets and tools used in the telecommunication industry

• Local operations and functional procedures of your company

• Personal computer (PC) operation, common PC terminology, and navigational

procedures in a windows-style user interface

Chapter Description

“About this document” This chapter

• Describes the guide's purpose, intended audience,

and organization

• Lists related documentation

• Explains how to comment on this document

Chapter 1, “Safety” Contains general safety information

Chapter 2, “Installation tools” Contains information on installation tools

Chapter 3, “Physical installation” Contains information on physical installation

...................................................................................................................................................................................................................................

1646 SMC





ix

Chapter Description

Chapter 4, “Power, cable, and fiber

installation”

Describes power, cable, and fiber installation

Chapter 5, “System turn-up and testing” Contains information on system turn-up and testing

Appendix A, “Miscellaneous

references”

This chapter includes the detailed installation

procedures for miscellaneous items and reference

material to complete installation, turn-up, and testing

of the system.

“Glossary” Defines and explains the following:

• Telecommunication terms

• Abbreviations

• Acronyms

Index Defines the index entries

Safety information

For your safety, this document contains safety statements. Safety statements are given at

points where risks of damage to personnel, equipment, and operation may exist. Failure to

follow the directions in a safety statement may result in serious consequences.

Related information

The following table lists the documents included in the documentation set:

Part Number Title Description

3KC18035ABABTQZZAAlcatel-Lucent

1646 SMC Release

2.1 Product

Information and

Planning Guide

This guide is for use by network planners, analysts,

and managers. It is also for use by the

Alcatel-Lucent Account Team. It presents a detailed

overview of the system, describes its applications,

gives planning requirements, engineering rules,

ordering information, and technical specifications.


1646 SMC Release

2.1 User

Provisioning Guide

This guide provides step-by-step information for

use in daily system operations. The manual

demonstrates how to perform system provisioning,

operations, and administrative tasks by use of

Zero-Installation Client (ZIC)


1646 SMC Release

2.1 Maintenance

and

Trouble-Clearing

Guide

This guide gives detailed information on each

possible alarm message. Furthermore, it provides

procedures for routine maintenance,

troubleshooting, diagnostics, and component

replacement.

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

x Alcatel-Lucent – Proprietary


1646 SMC



Part Number Title Description


1646 SMC Release

2.1 Installation and

System Turn-Up

Guide

This guide is a step-by-step guide to system

installation and setup. It also includes information

needed for pre-installation site planning and

post-installation acceptance testing.


1646 SMC Release

2.1 TL1 User

Provisioning Guide

Provides information on provisioning procedures

by means of Translator Language 1 (TL1)

commands


1646 SMC Release

2.1 Safety Guide

Provides information and safety guidelines to

safeguard against personal injury and to prevent

material damage to the equipment.

Technical support

For technical support, contact your local Alcatel-Lucent customer support team. See the

Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact

information.

How to order

To order Alcatel-Lucent documents, contact your local sales representative or use Online

Customer Support (OLCS) (http://support.alcatel-lucent.com)

How to comment

To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-

lucent.com/comments/) or e-mail your comments to the Comments Hotline

([email protected]).

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





xi

http://www.alcatel-lucent.com/support/

http://www.alcatel-lucent.com/support/

http://support.alcatel-lucent.com



http://infodoc.alcatel-lucent.com/comments/



mailto:[email protected]

mailto:[email protected]

About this document

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

xii Alcatel-Lucent – Proprietary


1646 SMC



1 1Safety

Overview

Purpose

This chapter provides important safety instructions for the Alcatel-Lucent 1646 SMC.

Contents

Structure of safety statements 1-2

Laser product classification 1-4

Laser safety 1-6

Electrostatic discharge ESD considerations 1-9

General safety 1-14

...................................................................................................................................................................................................................................

1646 SMC





1-1

Structure of safety statements

Overview

This topic describes the components of safety statements that appear in this document.

General structure

Safety statements include the following structural elements:

Item Structure element Purpose

1 Safety alert symbol Indicates the potential for personal injury

(optional)

2 Safety symbol Indicates hazard type (optional)

3 Signal word Indicates the severity of the hazard

4 Hazard type Describes the source of the risk of damage or

injury

5 Safety message Consequences if protective measures fail

6 Avoidance message Protective measures to take to avoid the hazard

7 Identifier The reference ID of the safety statement

(optional)

Signal words

The signal words identify the hazard severity levels as follows:

Signal word Meaning

DANGER Indicates an extremely hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

SAMPLEB C D

E F

G

H

Lifting this equipment by yourself can result in injurydue to the size and weight of the equipment.

Always use three people or a lifting device to transportand position this equipment. [ABC123]

CAUTION

Lifting hazard

Safety Structure of safety statements

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1-2 Alcatel-Lucent – Proprietary


1646 SMC



Signal word Meaning

CAUTION Indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

NOTICE Indicates a hazardous situation not related to personal injury.

Safety Structure of safety statements

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-3

Laser product classification

Standards compliance

The product complies with both IEC standards and the Food and Drug Administration’s

Center for Devices and Radiological Health (FDA/ CDRH) regulations.

FDA/CDRH regulations

Laser products are classified in accordance with the FDA/CDRH - 21 CFR 1010 and

1040. The classification scheme is based on the ability of the laser emission to cause

injury to eye or skin during normal operating conditions.

In the United States, lasers and laser systems in the infrared wavelength range (greater

than 700 nm) are assigned to one of the following classes:

• Class I

• Class IIIb

• Class IV

Laser classification is dependent upon operating wavelength, output power and fiber

mode field diameter (core diameter).

IEC requirements

The International Electro-Technical Commission (IEC) establishes standards for the

electrical and electronic industries. IEC-60825 has been established for the worldwide

safety of laser products.

According to the IEC classification, lasers and laser systems in the infrared wavelength

range (greater than 700 nm) are assigned to one of the following classes:

• Class 1

• Class 3A

• Class 3B

• Class 4

There are some major differences between the FDA/CDRH regulations and IEC:

1. The Accessible Emission Limits (AEL) are different.

2. Class 3A applies to all wavelengths.

3. Class 3B requires strict engineering controls.

4. Classification is under single fault conditions.

Safety Laser product classification

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Laser classes

The maximum output power of laser radiation depends on the type of laser diode used.

The international standards IEC-60825 or DIN/EN 60825 define the maximum output

power of laser radiation for each laser class in accordance with the wavelength.

Table 1-1 Laser classes

Laser class Wavelength Maximum output power

of laser radiation

I 1310 nm 8.85 mW

1550 nm 10 mW

3A 1310 nm 24 mW

1550 nm 50 mW

3B 1310 nm 0.5 W

1550 nm 0.5 W

Hazard level assignment

Hazard level refers to the potential hazard from laser emission at any location in an

end-to- end optical fiber communication system that may be accessible during service or

in the event of a failure. The assignment of hazard level uses the AELs for the classes.

Hazard levels for optical transmission equipment are assigned in either of the following

two ways:

• Actual output power from the connector or fiber cut.

• If automatic power reduction is used, output power at the connector or fiber cut at one

second after automatic power reduction takes place provided that maximum output

and restart conditions are met.

Classification of optical telecommunication equipment

Optical telecommunication equipment is generally classified as IEC Class 1 or

FDA/CDRH Class I, because under normal operating conditions, the transmitter ports

terminate on optical fiber connectors.

Safety Laser product classification

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-5

Laser safety

System design

The Alcatel-Lucent system complies with FDA/CDRH 21 CFR 1040.10 and 1040.11 as a

Class I and with IEC 60825-1 as a Class 1 Optical Fiber Telecommunication laser

product. The system has been designed to ensure that the operating personnel is not

endangered by laser radiation during normal system operation. The safety measures

specified in the Food and Drug Administration’s Center for Devices and Radiological

Health (FDA/CDRH) regulations and the international standards IEC-60825 or DIN/EN

60825 are met. Please also refer to “Laser product classification” (p. 1-4).

Potential sources of danger

Beware of the following potential sources of danger which will remain despite all safety

measures taken:

• Laser radiation can cause damage to the skin and eyes.

• Laser radiation from optical transmission systems is in a wavelength range that is

invisible to the human eye.

Laser warning labels

The laser warning labels indicate either only the laser class or both the laser class and the

maximum output power of laser radiation. The following figure shows different types of

laser warning labels and their characteristics.

Safety Laser safety

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Legend:

1. Laser symbol.

2. Laser classification label. This label may show only the laser class or both the laser class and

the maximum output power.

3. Laser warning label.

Figure 1-1 Laser warning label

Safety Laser safety

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-7

Laser safety instructions

Observe the following instructions to avoid exposing yourself and others to risk.

• Read the relevant descriptions in the manuals before taking equipment into operation

or carrying out any installation and maintenance work on the optical port units, and

follow the instructions. Ignoring the instructions can result in exposure to dangerous

radiation.

• Do not view directly into the laser beam with optical instruments such as a fiber

microscope, because viewing of laser emission in excess of Class 1 limits

significantly increases the risk of eye damage.

• Never look into the end of an exposed fiber or an open connector as long as the

optical source is still switched on.

• Ensure that the optical source is switched off before disconnecting optical fiber

connectors.

• Once a fiber is disconnected, check that the optical source is switched off by

measuring with an optical power meter.

• When connecting fiber loops between the IN and OUT ports on optical circuit packs,

always connect to the IN port first and then the OUT port. This will prevent any

optical radiation from being present at the fiber end.

Safety Laser safety

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Electrostatic discharge ESD considerations

ESD precautions

NOTICE

ESD hazard

Industry experience has shown that all integrated circuit packs can be damaged by static

electricity that builds up on work surfaces and personnel. The static charges are produced

by various charging effects of movement and contact with other objects. Dry air allows

greater static charges to accumulate. Higher potentials are measured in areas with low

relative humidity, but potentials high enough to cause damage can occur anywhere.

In order to prevent damage by electrostatic discharge the following precautions should be

observed when handling circuit packs:

• Assume all circuit packs contain solid state electronic components that can be

damaged by ESD.

• When handling circuit packs (storing, inserting, removing, etc.) or when working on

the backplane, always wear a grounded wrist strap such as the one shown in Figure

1-2, “Static control wrist strap” (p. 1-10) or wear a heel strap and stand on a

grounded, static dissipating floor mat. If a static dissipating floor mat is used, be sure

that it is clean to ensure a good discharge path.

• Handle all circuit packs by the faceplate or latch and by the top and bottom outermost

edges. Never touch the components, conductors, or connector pins.

• Observe warning labels on bags and cartons. Whenever possible, do not remove

circuit packs from antistatic packaging until ready to insert them into slots.

• Always open all circuit packs at a static safe work position, using properly grounded

wrist straps and static dissipating table mats. If a static dissipating floor mat is used,

be sure that it is clean to ensure a good discharge path.

• Always store and transport circuit packs in static safe packaging. Shielding is not

required unless specified.

• Keep all static generating materials such as food wrappers, plastics, and styrofoam

containers away from all circuit packs. Upon removal from bay, immediately put

circuit packs into static safe packages.

• Whenever possible, maintain relative humidity above 20 percent.

To reduce the possibility of ESD damage, assemblies are equipped with grounding jacks

to enable personnel to ground themselves using wrist straps [Figure 1-2, “Static control

wrist strap” (p. 1-10)] while handling circuit packs or working on an assembly. The jacks

for connection of wrist straps are located at the lower right-hand corner of each assembly

and are labeled. When grounding jacks are not provided, an alligator clip adapter enables

connection to ground.

Safety Electrostatic discharge ESD considerations

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-9

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

READ AND UNDERSTAND ALL INSTRUCTIONS

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying this product.

When installing, operating, or maintaining this equipment, basic safety precautions

should always be followed to reduce the risk of fire, electric shock, and injury to persons,

including the following:

Instruction

number

Instruction

1 Read and understand all instructions.

2 Follow all warnings and instructions marked on this product.

3 This product should be only operated from the type of power sources indicated on

the marking label.

4 Connect this product only to the type of power sources recommended by

Alcatel-Lucent.

Figure 1-2 Static control wrist strap


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Instruction

number

Instruction

5 This equipment is suitable for mounting on a concrete or other noncombustible

surface only.

6 Install only equipment identified in this manual. Use of other equipment may

result in improper connection of circuitry leading to fire or injury to persons.

7 All metallic telecommunication interfaces should not leave the building premises

unless connected to telecommunication devices providing primary and secondary

protection, as applicable.

8 Do not use this product near water, for example, in a wet basement.

9 Do not place this product on an unstable cart, stand or table. The product may fall,

causing serious damage to the product.

10 Use caution when installing or modifying telecommunications lines.

11 Never install telecommunications wiring during a lightning storm.

12 Never install telecommunications connections in wet locations.

13 Never touch uninsulated telecommunications wires or terminals unless the

telecommunications line has been disconnected at the network interface.

14 Never touch uninsulated wiring or terminals carrying direct current or ringing

current, or leave this wiring exposed. Protect and tape uninsulated wiring and

terminals to avoid risk of fire, electric shock, and injury to service personnel.

15 Never push objects of any kind into this product through slots as they may touch

dangerous voltage points or short out parts that could result in a risk of fire or

electrical shock. Never spill liquids of any kind on the product.

16 Slots and openings in the unit are provided for ventilation, to protect it from

overheating, and these openings must not be blocked or covered. This product

should not be placed in a built-in installation unless proper ventilation is provided.

17 To reduce the risk of an electrical shock, do not disassemble this product. Service

should be performed by trained personnel only. Opening or removing covers

and/or circuit boards may expose you to dangerous voltages or other risks.

Incorrect reassembly can cause electrical shock when the unit is subsequently

used.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-11

Instruction

number

Instruction

18 Some of the hardware modules contain FDA/CDRH Class I/IEC Class 1

single-mode laser products that are enclosed lightwave transmission systems.

Under normal operating conditions, lightwave transmission systems are

completely enclosed; nonetheless, the following precautions must be observed

because of the potential for eye damage:

1. Do not disconnect any lightwave cable or splice and stare into the optical

connectors terminating the cables.

2. Lightwave/lightguide operations should not be performed by a technician who

has not satisfactorily completed an approved training course.

3. Do not use optical instruments such as an eye loupe to view a fiber or

unterminated connector.

4. More information about laser safety can be found in the Installation Manual.

19 For a unit intended to be powered from –48V DC voltage sources, read and

understand the following:

• Disconnect up to Two (2) power supply connections when removing power

from the system.

• This equipment must be provided with a readily accessible disconnect device

as part of the building installation.

• Ensure that there is no exposed wire when the input power cables are

connected to the unit.

• Installation must include an independent frame ground drop to building

ground.

• This Equipment is to be Installed Only in Restricted Access Areas on Business

and Customer Premises Applications in Accordance with Articles 110-16,

110-17, and 110-18 of the National Electrical Code, ANSI/NFPA No. 70.

Other Installations Exempt from the Enforcement of the National Electrical

Code May Be Engineered According to the Accepted Practices of the Local

Telecommunications Utility.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Instruction

number

Instruction

20 For a unit intended to be powered from 100-120/200-240 V ac voltage sources,

read and understand the following:

• Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

• Do not staple or otherwise attach the power supply cord to the building

surfaces.

• Do not overload wall outlets and extension cords as this can result in the risk

of fire or electric shock.

• The socket outlet shall be installed near the equipment and shall be readily

accessible.

• This product is equipped with a three-wire grounding type plug, a plug having

a third (grounding) pin. This plug is intended to fit only into a grounding type

power outlet. This is a safety feature. If you are unable to insert the plug into

the outlet, contact your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the grounding type plug. Do not use a

3-to-2-prong adapter at the receptacle. Use of this type adapter may result in

risk of electrical shock and/or damage to this product.

• Do not allow anything to rest on the power cord. Do not locate this product

where the cord may be abused by persons walking on it.

a. When the powers supply cord or plug is damaged or frayed.

b. If liquid has been spilled into the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions because improper adjustment of other controls may result in

damage and will often require extensive work by qualified technician to

restore the product to normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. If the product exhibits a distinct change in performance.

SAVE THESE INSTRUCTIONS


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-13

General safety

Rules for shielded cables

WARNING

Electric-shock hazard

The intra-building port(s) of the equipment or subassembly is suitable for connection to

intra-building or unexposed wiring or cabling only. The intrabuilding port(s) of the

equipment or subassembly MUST NOT be metallically connected to interfaces that

connect to the Outside plant or its wiring. These interfaces are designed for use as

intra-building interfaces only and require isolation from the exposed Outside plant

cabling.

The addition of Primary Protectors is not sufficient protection in order to connect these

interfaces metallically to Outside plant wiring.

Caution to avoid equipment damage

Figure 1-3 Correct operations for card insertion

Safety General safety

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Refer to the “Caution to avoid Equipment damage” (p. 3-2) for a detailed description of

card insertion and card extraction.

Proper card alignment

CAUTION


Do not push on one lever only.

Do not force the units.

Avoid impact during the units handling.

1. Do not force the card into the subrack slot.

2. For correct insertion into the subrack slot, ensure that the card and subrack slot are

properly aligned.

Card extraction

Important! Always remove (power) cable before extracting (or inserting) a unit and/or a

Main Card.

Card extraction procedure is the reverse of the card insertion procedure.

Refer to the “Caution to avoid Equipment damage” (p. 3-2) for a detailed description of

card insertion and card extraction.

Figure 1-4 Card alignment


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





1-15


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



2 2Installation tools

Overview

Purpose

This chapter describes the installation tools of the Alcatel-Lucent 1646 SMC.

Contents

List of installation tools 2-2

Special tools and test equipment 2-4

Method of procedure 2-5

...................................................................................................................................................................................................................................

1646 SMC





2-1

List of installation tools

The following is a list of tools and materials used to install equipment. Tools specific to a

physical installation are listed in Chapter 3, “Physical installation” covering the task.

Other tools might be required to perform special procedures. These tools should be

gathered in advance in preparation for installing the system.

• reference manuals

• Safety glasses and ear protection

• Box cutter or pocket knife

• Static-protection accessories

– Strap, wrist ground (PN 047-9004-010)

– Coiled cord, six foot (PN 047-9004-020)

– ESD Field Service Grounding Kit (PN 1AD012520001)

• BNC connector crimping tool, Thomas & Betts WD416

• Small Thomas & Betts power crimping tool for coaxial cable end connections

• Screwdrivers, standard (slot head)

– 4-inch shaft

– 6-inch shaft

– Small (to fit screws on interrack data cables)

– 1/8-inch, 8 inches long

• Screwdrivers, Phillips

– 6-inch shaft

– 12-inch shaft

– Power screwdrivers with No. 0 and No. 1 bits

– 90X

• Insulated trouble lamp (droplight duralamp)

• Extension cord (50-foot)

• Ladders and/or portable scaffold

• Wrenches (3/8- to 11/16-inch), open and box-end combination

• Socket set, 3/8-inch drive with ratchet handle and extension

• Foot-pound torque wrench

• Thread-cutting screws

• Needle-nose pliers, 4-1/2 inch

• Diagonal cutters, 5 inch

• Cable butting tool

• Cable cutters

• Cable stripper

• Multi-stripper

• Anti-oxidation compound

Installation tools List of installation tools

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



• Steel measuring tape (50 feet)

• Accurate level

• Chalk line and chalk (blue)

• Felt-tipped marking pen

• Stencil kit

• Vacuum cleaner, high-efficiency particulate Arrester (HEPA)

• V-bolts, corner and wall brackets, channels, and other hardware for overhead cabling

Installation tools List of installation tools

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





2-3

Special tools and test equipment

Description

In addition to the standard tools, there are special tools that are used on the shelf. Details

about these tools can be found in Appendix A, “Miscellaneous references”.

• Mini BNC tool

• RJ45 tool

• SFP extraction tool

Installation tools Special tools and test equipment

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Method of procedure

Description

The person responsible for the installation, in cooperation with the TAC team and Central

Office (CO) supervisor, should collect all essential information to prepare a Method of

Procedure (MOP). When the MOP is complete, it should be submitted to CO management

for approval. Any work on common equipment may need to be performed during

nonstandard working hours. This should be a joint decision between the CO management,

the TAC team, and the installation personnel.

As a minimum requirement, the following items should be addressed, mutually

understood, and agreed upon to establish a MOP before installation:

• Service-affecting hazards involved and associated risks imposed

• Installation methods and tools

• Experienced personnel assigned to job

• Protection requirements for equipment and tools

• Time during which various steps of work will be performed, and a list of equipment

that is affected

• Identified steps of work that require notification of TAC team before work starts

• Procedures to follow and tests to complete before connecting additional or modified

equipment to any working equipment

• Steps installer must take to disconnect any alarms associated with the work.

• Procedures to ensure that designation and fuse records are checked against proper

drawings before any fuse is removed

• Time that equipment removed from service is restored

• Additional measures to take to ensure that equipment is restored to service on time in

case of delays

• Identified steps of work that require presence of CO personnel

• Tests applicable for wiring operations

• Space requirements (for example, storage and administration)

• When applicable, a restoration plan that will be a joint effort between CO personnel,

TAC team, and installation personnel

• Steps required to ensure that all work is done during hours specified in the MOP

• MOP approval by TAC team and CO personnel before installation

• An approved copy of the MOP available and posted for review at job site at all times

Note: After the MOP is adopted and approved, it cannot be deviated from without

approval of the TAC team and the CO personnel.

Installation tools Method of procedure

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





2-5

Installation tools Method of procedure

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



3 3Physical installation

Overview

Purpose

This chapter contains a set of procedures to install the Alcatel-Lucent 1646 SMC.

Contents

Caution to avoid Equipment damage 3-2

Unpack and inspect equipment 3-4

Preparation 3-6

...................................................................................................................................................................................................................................

1646 SMC





3-1

Caution to avoid Equipment damage

Right operations for unit insertion

The following are the steps for unit insertion:

1. Open the levers first, to plug the unit.

2. To mate the plastic body of the connectors, push the front panel, balancing the strain

without pushing on the levers.

3. Push on the levers in order to finish the connector mating.

4. Fix the unit to the subrack by means of screws, before inserting another unit.

Forbidden operations for unit insertion

1. Do not push just on one lever only.

Physical installation Caution to avoid Equipment damage

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



2. Do not force the units.

3. Avoid impact during the units handling.

Right operations for unit extraction

1. Unscrew the top and bottom screws before extracting the unit.

2. Act on the levers opening gently as shown in the above figure.

3. Pull the unit as shown in the figure.

Physical installation Caution to avoid Equipment damage

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-3

Unpack and inspect equipment

Purpose

Follow this procedure to unpack and inspect the and to report any shipping damage or

missing parts.

Note: Alcatel-Lucent provides expert Installation Services for installations that have

different requirements from those outlined in this manual. Contact Alcatel-Lucent at

1-888-252- 2832 for details.

Recommended tools

Recommended tools include a box cutter or a pocket knife.

Hazards

CAUTION


Equipment damage

Exercise care when moving equipment to avoid excessive shock or vibration, which can

damage equipment.

Preliminary checks

The following information should be printed on the outer box:

• International Symbols

• Trademark/address of the manufacturing company.

• Labels (or template marks) indicating information on the contract and destination site

of the product.

• An envelope containing packing list and other information.

Procedure

...................................................................................................................................................................................................

1 Upon receipt, check the following:

• The final destination as indicated on the container.

• The cases are undamaged.

Physical installation Unpack and inspect equipment

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

2 Report any shipping damages to the company’s representative or the shipping agent.

...................................................................................................................................................................................................

3 When unpacking, proceed as follows:

1. Ensure that outer packing is properly positioned.

2. Open the case.

3. Remove the shock proof material.

4. Remove the chassis from the case.

5. Remove pre-packing, polyethylene bag, and any other protection.

6. Remove the plastic bags containing accessories taped to the racks.

7. Remove any dehydrating bags.

8. Check that the goods are not damaged, and that they correspond to those indicated on

the packing list. Contact the shipping agency’s representative if discrepancies are

found.

...................................................................................................................................................................................................

4 Handle the packing material with care; it can be reused for repacking again if goods must

be re-shipped.

...................................................................................................................................................................................................

5 If packing material needs to be stored, the cardboard boxes must be placed indoors in

ventilated rooms.

...................................................................................................................................................................................................

6 Stop: This procedure is complete.

Physical installation Unpack and inspect equipment

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-5

E N D O F S T E P S...................................................................................................................................................................................................

Preparation

Description

This section provides physical details and guidelines for installation.

Observe the following guidelines:

• Verify that layouts of mounting rack or wall mount position are as indicated in

applicable drawings and specifications.

• Verify that area dimensions and location of reference points correspond to plan.

• Mark all reference and layout lines.

The chassis will be rack, wall, or desk mounted as described in the following sections.

For all mounting arrangements, adequate ventilation space is required at the top and sides

of each unit. Adjacent equipment should not be stacked or placed in such a way as to

block ventilation panels. Refer to the site engineering specification for site specific

spacing and ventilation requirements.

Before you begin

The following tools are needed for installation:

• Tape measure

• Philips screwdriver

• Flathead screwdriver

• Adjustable wrench

• Heat gun

• Paper knife

• Ratchet crimp tool

• Cable cutter

• Wire stripper

• Coax stripper

• Network cable crimping pliers

• Diagonal pliers

• Crimping tool

• Cable tester

• Multimeter

• Claw hammer

• Percussion drill

• Marker pen

Physical installation Preparation

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC




....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-7

CAUTION

To facilitate heat dissipation of the Alcatel-Lucent 1646 SMC, leave a

space of 1U above or below the chassis.

Note: By default, the chassis of the Alcatel-Lucent 1646 SMC is installed with the

mounting ear for the 19-inch cabinet before delivery.

Install the chassis in the 19-Inch cabinet

...................................................................................................................................................................................................

1 Fix the chassis in the 19-inch cabinet.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

2 Install the PGND cable.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-9

E N D O F S T E P S...................................................................................................................................................................................................

Install the chassis in the ETSI cabinet

...................................................................................................................................................................................................

1 Select mounting holes based on the type of the cabinet.

...................................................................................................................................................................................................

2 Install the transit mounting ears for the ETSI cabinet.

...................................................................................................................................................................................................

3 Install the PGND cable.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

4 Fix the chassis in the ETSI cabinet.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-11

E N D O F S T E P S...................................................................................................................................................................................................

Install the chassis on a wall

...................................................................................................................................................................................................

1 Install the mounting ears for a 19-inch cabinet (wall-mount).

...................................................................................................................................................................................................

2 Install the expansion bolts in the wall.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

3 Install the PGND cable and fix the chassis that is mounted on the wall.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-13

E N D O F S T E P S...................................................................................................................................................................................................

Install the chassis on the desktop

CAUTION

To facilitate heat dissipation of the Alcatel-Lucent 1646 SMC, leave a

space of 1U above or in between the chassis and the bracket.

...................................................................................................................................................................................................

1 Remove the mounting ears for the 19-inch cabinet from the two sides of the chassis.

...................................................................................................................................................................................................

2 Install the PGND cable and fasten the chassis onto the bracket on the two sides of the

chassis.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





3-15


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



4 4Power, cable, and fiber

installation

Overview

Purpose

This chapter includes a list of procedures for installing power and signal transmission

cables on the Alcatel-Lucent 1646 SMC.

The Alcatel-Lucent 1646 SMC can be installed in Network Telecommunications Facilities

or in customer premise locations where the NEC applies. With appropriate options for

environmental (temperature and humidity) hardening, the Alcatel-Lucent 1646 SMC can

be installed in outside plant (OSP) locations.

Contents

Install ground and power cables 4-2

Power cable installation 4-5

Connect management and alarm cables 4-6

Signal transmission cables 4-8

...................................................................................................................................................................................................................................

1646 SMC





4-1

Install ground and power cables

Purpose

This procedure provides instructions to route and connect station-ground cables to

equipment racks and ground the PDU to the rack.

General

The Alcatel-Lucent 1646 SMC shelf is grounded to the rack through the thread-forming

screws used to install the shelf in a rack and also by a separate ground cable. For both the

AC and DC power options, a ground lug is located on the left side of the chassis.

...................................................................................................................................................................................................

1 Refer to the job site documentation for the exact rack layout and cable specifications.

...................................................................................................................................................................................................

2 Complete an identification tag for each power cable, then attach the tag to the cable.

...................................................................................................................................................................................................

3 Install ground and power connections using the procedures “AC-powered” (p. 4-2) and

“DC-powered” (p. 4-3) for the AC-powered or DC-powered equipment type.

AC-powered

...................................................................................................................................................................................................

1 Attach grounding wire between the UL safety ground screw located in the middle of the

left side chassis and appropriate safety ground. If the safety ground is located on a rack

system, ensure that the rack itself is properly grounded.

...................................................................................................................................................................................................

2 Route and secure the AC power cord. Verify that the designated AC power source outlet is

surge protected. Reference the site engineering specification for any additional site

specific AC requirements.

Power, cable, and fiber installation Install ground and power cables

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................

...................................................................................................................................................................................................

3 Connect the AC power cord to the connector and leave the other end disconnected. For

rack-mounted units, the AC cord will be connected to an AC power breakout panel in the

rack. Leave the AC power disconnected until you are ready to perform the procedures in

Chapter 5, “System turn-up and testing”. The Alcatel-Lucent 1646 SMC has four (4)

supported AC power cables based on local power source type and included in the

installation kit.

...................................................................................................................................................................................................

4 STOP. This procedure is complete. Continue with the next section for cable installation.

DC-powered

...................................................................................................................................................................................................

1 Refer to the site engineering specification to determine if a common grounding (bonding)

arrangement will be used. If common bonding network (CBN) is specified for -48V/-60V

operation, attach a separate grounding wire between the UL safety ground terminals

located in the middle of the power terminal block and the +VA and +VB terminals.

If isolated bonding network (IBN) is specified, make no connections to the center ground

terminals.

Figure 4-1 AC power connector


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





4-3

E N D O F S T E P S...................................................................................................................................................................................................

...................................................................................................................................................................................................

2 Verify with an ohmmeter that the Alcatel-Lucent 1646 SMC shelf is grounded properly.

Measure less than 1 ohm between the shelf safety ground screw and the appropriate frame

ground.

...................................................................................................................................................................................................

3 Verify with an ohmmeter that the ESD jack on the front of the shelf is grounded properly.

Measure less than 1 ohm between the ESD jack and the appropriate frame ground.

Figure 4-2 DC power connector


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................

Power cable installation

This section provides instructions on installing DC power cabling for the shelf.

Each power feeder (A and B) requires a single power feed from the battery distribution

fuse board (BDFB), or the battery distribution circuit breaker bay (BDCBB) to the shelf.

If the is powered through only one power feed, the system will report a minor alarm. To

suppress the alarm, use two jumpers, one jumper between the -VA and -VB and the

second jumper between +VA and +VB. The gauge of both jumpers should be the same as

the gauge being brought in from the Battery Plant (#12AWG to #16AWG).

-VA +VA -VB +VB ALARM

Connect Connect No connect No connect Minor

No connect No connect Connect Connect Minor

Connect Connect Connect Connect None

Connect Connect Jumper form

-VA

Jumper form

+VA

None

Jumper form

-VB

Jumper form

+VB

Connect Connect None

Procedure

...................................................................................................................................................................................................

1 Verify that the power source is off.

...................................................................................................................................................................................................

2 Connect the A and B power cables to the A and B connector pins of the terminal block

located on the top right. Use a torque screwdriver set to 0.5 nm (4.4 lb-in) to tighten.

...................................................................................................................................................................................................

3 Route the power cables toward the power source (for example: BDCBB and BDFB).

...................................................................................................................................................................................................

4 Splice feeders from the BDCBB or BDFB to the power cables.

...................................................................................................................................................................................................

5 Label the feeders at the power source as follows: -VA, +VA, -VB, and +VB.

...................................................................................................................................................................................................

6 Leave the power supply mechanism disconnected at the power source until you are ready

to perform the procedures in Chapter 5, “System turn-up and testing”.

Power, cable, and fiber installation Power cable installation

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





4-5

E N D O F S T E P S...................................................................................................................................................................................................

Connect management and alarm cables

Description

This section contains procedures to connect external management and alarm systems.

RS232 local management

The port designated as “RS232 Local Craft” Terminal needs PPP protocol.

Pin RJ45 Function (connect

to F2/DBG RJ-45 port of

MB16)

COM Function (DB9) (connect to

COM port of computer)

1

2 RXD232

3 TXD232

4 GND

5 GND

6

7 RXD232

8 TXD232

Power, cable, and fiber installation Connect management and alarm cables

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Ethernet LAN local or remote management

Local or remote management is provided through a LAN connection. This connection

requires IP configuration after the system is turned up.

...................................................................................................................................................................................................

1 For rack mount applications, route and secure the twisted pair (568A or 568B) along the

right side of the equipment rack. Alternately, for wall or table applications, route and

secure the twisted pair (568A or 568B) per job site specifications.

...................................................................................................................................................................................................

2 Connect the twisted pair (568A or 568B) to the front panel LAN RJ45 connector.

Power, cable, and fiber installation Connect management and alarm cables

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





4-7

E N D O F S T E P S...................................................................................................................................................................................................

Signal transmission cables

Equipment options

Review the ordering information and site engineering specifications to determine

quantities and list the types of the signal transmission cables to be installed.

Note: each equipment option has a different front panel connector layout according to

the interfaces required. Specific quantities and types of cables will correspond to the

equipment type being installed.

For each cable interface type, select the appropriate cable installation procedure from the

following sections. For all cable types, ensure that strain relief and bending radius is

maintained for the type of cable being installed. Refer to the site engineering specification

for any site-specific or customer-specific cabling instructions.

10/100/1000Base-T Ethernet cables

...................................................................................................................................................................................................

1 Identify and label all Ethernet cables per the site engineering specification.

...................................................................................................................................................................................................

2 Route and secure cables on the left side for rack-mount applications or per site

engineering specification for wall-mount or table applications.

...................................................................................................................................................................................................

3 Insert the 10/100/1000Base-T RJ45 connectors into the designated jacks on the

Alcatel-Lucent 1646 SMC faceplate panel. Ensure that the retention slide locks operate

and that there is adequate strain relief.

Install SFPs

...................................................................................................................................................................................................

1 Verify the correct type and quantities of SFPs per the site engineering specification. SFP

types and part numbers are listed in Appendix A, “Miscellaneous references”.

...................................................................................................................................................................................................

2 Remove the dust cover from the SFP cage on the faceplate.

...................................................................................................................................................................................................

3 Remove the pluggable module from its packaging.

...................................................................................................................................................................................................

4 If the SFP module contains a latching mechanism, ensure the bail latch is closed (folded

back in the SFP module).

Note: Some SFP types do not have a latch.

Power, cable, and fiber installation Signal transmission cables

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................

...................................................................................................................................................................................................

5 While holding the SFP module with the side where the electrical connections are exposed

to the bottom, slide the SFP module into one of the receptacles in the faceplate.

Note: To remove an SFP, first disconnect the fiber optic cable from the pluggable

module. If the SFP module is equipped with a bail latch, open the latch outward to

disengage the module from the receptacle. Open the latch until it is perpendicular to

the face of the module. Use the bail latch to carefully pull the SFP module out of its

cage on the faceplate. Make sure to apply the extraction force in a direction parallel to

the long dimension of the SFP module. If the SFP receptacle will remain empty, insert

a dust cover to prevent contamination of the electrical connector. Place the pluggable

module back into its ESD-protective packaging.

If the SFP is not equipped with a bail latch, an extraction tool should be used. Using

the tool carefully unlatch the retaining tabs and gently pull the SFP in a direction

parallel to the long dimension of the module.

...................................................................................................................................................................................................

6 Repeat the above steps for each SFP to be installed.

Gigabit Ethernet (GE) fiber

...................................................................................................................................................................................................

1 Identify and label all GE fiber per the job specification.

Note: GE fibers are terminated with LC type connectors which will connect to the

Alcatel-Lucent 1646 SMC via SFPs installed in the Alcatel-Lucent 1646 SMC

faceplate. It is essential that the SFP type, multi-mode or single mode, matches the

laser and fiber being installed.

...................................................................................................................................................................................................

2 Route and secure the fiber along the right side of the equipment rack for rack-mount

applications or per job specification for wall or table applications.

...................................................................................................................................................................................................

3 Connect the LC connector securely to the designated SFP (previously installed).

...................................................................................................................................................................................................

4 Connect all fibers required by the site engineering specification.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





4-9

E N D O F S T E P S...................................................................................................................................................................................................

E N D O F S T E P S...................................................................................................................................................................................................

E1 cables

...................................................................................................................................................................................................

1 Route and secure the E1 cable along the right side of the equipment rack for rack-mount

applications or per site engineering specification for wall or table applications.

...................................................................................................................................................................................................

2 Connect the E1 cable to the Alcatel-Lucent 1646 SMC faceplate connector labelled E1.

...................................................................................................................................................................................................

3 Connect the other end of the E1 cable to the 75-ohm unbalanced termination points per

the site engineering specification.

Figure 4-3 E1 cables


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................

5 5System turn-up and

testing

Overview

Purpose

This chapter describes the system turn-up and testing of the Alcatel-Lucent 1646 SMC.

Contents

Requirements 5-2

NE turn-up and testing 5-3

Software upgrade using ZIC 5-11

Troubleshooting 5-17

...................................................................................................................................................................................................................................

1646 SMC





5-1

Requirements

Hardware requirements

The following hardware resources are needed:

• PC

• Debug cable

One end of Debug cable is RJ45 for the F2/DBG port and the other end is DB9 for the

PC. The signals related to pins are defined in the table below:

F2/DBG Signal name RJ45 Connector pin

(Pins at the top)

DB9 Pin

DBG_TXD 8 2

DBG_RXD 7 3

GND 4 5

• Network cable (Common network cable with parallel line)

Software requirements

The following software resources are needed:

• Internet Explorer

• Debug terminal tool. Example: HyperTerminal

• FTP Server Tool

• ZIC software package

• NE software package

Note: Ensure that the NE is correctly installed according to Chapter 3, “Physical

installation”.

Connection between the PC and the NE is established using the debug cable and the

network cable as follows:

• For Debug cable, connect the DB9 connector to the COM port of PC and connect the

RJ45 connector to the F2/DBG port of the NE on mainboard.

• For Network cable, connect one side to the NIC of PC and the other side to LAN port

of NE on mainboard.

System turn-up and testing Requirements

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



NE turn-up and testing

Before you begin

Verify the following details:

• Ensure the NE is reachable from PC using “ping”. The default IP of NE from factory

is 129.9.191.240 and user can modify it. See the Alcatel-Lucent 1646 SMC Release

2.1 User Provisioning Guide for additional information. Hence, the IP will be

129.9.191.240 or any other value that the user has defined.

• The IP address of the PC must be set to the same network segment as the NE.

...................................................................................................................................................................................................

1 Install ZIC software that comprises of two parts in the following order:

1. ZIC-FC-Launcher_R2.1.x.exe

2. ZIC-FC-1646SMC_R2.1.y.exe

...................................................................................................................................................................................................

2 Run the ZIC-FC-Launcher application. Select Start→All Programs→ZIC

Launcher→ZICFullClient.

...................................................................................................................................................................................................

3 In the ZIC-FC-Launcher, Click Add to define NE as shown in Figure 5-1,

“ZIC-FC-Launcher” (p. 5-4).

System turn-up and testing NE turn-up and testing

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-3

...................................................................................................................................................................................................

4 Input the IP address of the NE to be connected in the Add Network Element window

displayed in Figure 5-2, “Add Network Element” (p. 5-5) and click OK.

Figure 5-1 ZIC-FC-Launcher


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

5 Verify the NE in the NE Check window as shown in Figure 5-3, “NE Check” (p. 5-6) and

click OK.

Figure 5-2 Add Network Element


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-5

...................................................................................................................................................................................................

6 Connect to the NE by selecting a defined NE as shown in Figure 5-4, “Connect to NE”

(p. 5-7) and click Open.

Figure 5-3 NE Check


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

7 The ZIC application opens in the browser as shown in Figure 5-5, “ZIC authentication

window” (p. 5-8). Enter the username and password in the authentication dialog window.

Click OK and the ZIC application opens as shown in Figure 5-6, “ZIC main window”

(p. 5-9).

Figure 5-4 Connect to NE


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-7

Figure 5-5 ZIC authentication window


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



The other two pop up windows that are displayed on successful login are:

Figure 5-6 ZIC main window


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-9


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................

Software upgrade using ZIC

Before you begin

Before upgrading the software ensure that FTP is installed and configured on the PC. See

“Install FTP server” (p. A-24) for information on installation of FTP server. Define

username and password for NE software upgrade.

Procedure

...................................................................................................................................................................................................

1 Run the ZIC-FC-Launcher application. Select Start→All Programs→ZIC

Launcher→ZICFullClient.

...................................................................................................................................................................................................

2 Connect to the NE by selecting a defined NE as shown in Figure 5-4, “Connect to NE”

(p. 5-7) and click Open.

...................................................................................................................................................................................................

3 The ZIC application opens in the browser as shown in Figure 5-5, “ZIC authentication

window” (p. 5-8). Enter the username and password in the authentication dialog window.

Click OK and the ZIC application opens as shown in Figure 5-6, “ZIC main window”

(p. 5-9).

...................................................................................................................................................................................................

4 Select System Management→DB Management→Remote File→Perform Copy as

shown in Figure 5-7, “Software upgrade” (p. 5-11).

Figure 5-7 Software upgrade

System turn-up and testing Software upgrade using ZIC

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-11

...................................................................................................................................................................................................

5 For software upgrade, set the parameters with the following values as shown in Figure

5-8, “Parameters in Remote File tab” (p. 5-12):

• From - Software Generic on a Remote Server (RFSSW)

• To - Active software generic on the NE (ACTSW). This value is set automatically.

• Set User, Password, Host, Port, and URL Path to the same values defined in the FTP

server tool.

...................................................................................................................................................................................................

6 Click Apply.

...................................................................................................................................................................................................

7 Click Yes to confirm the software upgrade as shown in Figure 5-9, “Confirm software

upgrade” (p. 5-13).

Figure 5-8 Parameters in Remote File tab


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

8 Click Close in the window shown in Figure 5-10, “Software upgrade confirmed”

(p. 5-13).

Figure 5-9 Confirm software upgrade

Figure 5-10 Software upgrade confirmed


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-13

...................................................................................................................................................................................................

9 The process and status of the software upgrade is shown in Figure 5-11, “Software

upgrade status” (p. 5-14).

...................................................................................................................................................................................................

10 Wait for the process of software upgrade to complete. The window shown in Figure 5-12,

“Software upgrade complete” (p. 5-15) is displayed after completion of the software

upgrade.

Figure 5-11 Software upgrade status


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

11 Select System Management→Initialize and Upgrade→Initialize System→With New

Release to activate the new software that was downloaded. Click Apply.

Figure 5-12 Software upgrade complete


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-15

...................................................................................................................................................................................................

12 The NE will reboot and run with new software.

...................................................................................................................................................................................................

13 After NE start up, connect to it using ZIC to check the version of the current software.

Select Equipment→System Information as shown in Figure 5-13, “System information”

(p. 5-16) and Figure 5-14, “System information details” (p. 5-16).

Note: For P8FES board, if a physical board is present, the software of the board will

be upgraded automatically during the “Copy Remote File” process.

Figure 5-13 System information

Figure 5-14 System information details


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



E N D O F S T E P S...................................................................................................................................................................................................

Troubleshooting

The Table 5-1, “List of possible issues and actions” (p. 5-17) lists the failures that can

occur and the actions to be taken to resolve them.

Table 5-1 List of possible issues and actions

Issues or failures Action to be taken

On addition of NE in the ZIC

launcher, the NE check fails

due to non availability of NE

type or NE release.

Ignore the issue and select the ZIC full client PKG release

manually.

The ZIC fails with the “SNMP

Agent cannot connect”

message.

Reboot the NE and login again.

The “Copy Remote File”

operation fails due to incorrect

software download state on the

NE. For example: NE starts up

or a previous software

download operation is

incomplete.

Wait for 15 minutes and retry.

If the failure count reaches 5, contact the field engineer.

The pop-up windows are not

displayed correctly or blocked.

Modify the configuration of your browser to allow pop-ups.

System turn-up and testing Troubleshooting

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-17

Table 5-1 List of possible issues and actions (continued)

Issues or failures Action to be taken

NE is reachable from PC using

“ping” but the login operation

fails.

• Check if the NE is in BIOS state using debugging terminal

and install the software in BIOS state.

• Start up the NE and check using debugging terminal.

Using a debug terminal tool, open a connection with

38400 baud rate.

For example, consider HyperTerminal:

– Configure serial port. See Figure 5-15, “Configure

serial port” (p. 5-19).

– Power on the NE. The start-up information is

displayed in the debug terminal. If “[DDM] Beat

Timer Proc Begin!” is displayed, the NE is in BIOS

state. See Figure 5-16, “Start-up information”

(p. 5-20).

• Upload the software to the NE:

– Before uploading, ensure software to be uploaded are

located in the PC. Software include FPGA, external

BIOS, nesoft, and configuration files for NE, adaptor,

and TL1 agent.

– Transfer the software to NE using FTP in IE or file

explorer with ftp://129.9.191.240/ directly (if IP

address of NE is 129.9.191.240). Username and

password are not needed.

– Transfer the tnhisu01.pga file to /ofs1/fpga/ directory

– Transfer the extbios.hwx file to /ofs1/hwx/ directory

– Transfer the nesoft.hwx, *.ini, *.log and *.txt to

/ofs1/hwx/ directory

• Reboot the NE using the “reboot” command in the debug

console or power cycle.

• NE starts up with the uploaded software.

Upgrade NE software using ZIC to align the NE software

version between package description file and the actually

running one.

Lost IP address of NE IP address of the NE can be retrieved using “dwGetSPIP”

command in the debug terminal (return value is in

hexadecimal format).


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Figure 5-15 Configure serial port


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





5-19

Figure 5-16 Start-up information


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Appendix A: Miscellaneous

references

Overview

Purpose

The appendix includes the detailed installation procedures for miscellaneous items and

reference material to complete installation, turn-up, and testing of the Alcatel-Lucent

1646 SMC system.

Contents

Fiber optic cleaning A-2

Cables, connectors, and assemblies A-6

Cable assembling instruction A-19

Install FTP server A-24

List of SFPs A-30

...................................................................................................................................................................................................................................

1646 SMC





A-1

Fiber optic cleaning

Purpose

This section provides the recommended instructions to clean fiber-optic connectors found

in Alcatel-Lucent equipment.

Prerequisite

Anyone who performs this procedure must be familiar with cleaning fiber-optic

connectors and with the specific system on which the procedure is to be performed.

This procedure must not be performed on traffic-carrying equipment. If a system is in

service, traffic must be removed from equipment to be cleaned.

Recommended tools

The following tools should be available for this procedure:

• Optical power meter with standard accessories

• Inspection microscope, 200X to 400X—Aerotech World Trade Ltd. AWT200 or

AWT300

• Inspection microscope tip

• Anti-static lint-free swab—Texwipe TX757E, Alcatel-Lucent PN 1552762010

• CLETOP®

fiber-optic cleaner — Aerotech World Trade Ltd. PN 14100500 for all

fiber-optic connectors

• Optical removal and cleaning tool—Alcatel-Lucent PN 3EM07060AAAA

• Penlight (pocket-style flashlight)

• Laser safety glasses

Miscellaneous references Fiber optic cleaning

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

A-2 Alcatel-Lucent – Proprietary


1646 SMC



Fiber cleaning procedure

DANGER

DO NOT LOOK INTO FIBER-OPTIC CONNECTOR

Laser infrared radiation is present when fiber-optic connector is open and optical

interface is installed. Laser infrared radiation is not visible to naked eye or with laser

safety glasses.

Ensure no optical power is connected to fiber being tested. An optical power meter must

be used to ensure all optical power has been removed.

Do not disassemble modules to clean fibers. Disassembling module could cause damage

to optical splices and could void warranty.

To preserve integrity of fiber-optic connectors, observe the following precautions:

• Do not use cleaning swabs more than once.

• Do not use alcohol or any type of liquid to clean fiber-optic connectors.

• Do not use canned air to clean fiber-optic connectors. Canned air propellant leaves

residue that clouds fiber-optic connectors.

• Do not touch polished optical surface of fiber-optic connector. Oil from skin can

degrade performance of fiber-optic connector and attract dust particles.

• Always use protective covers to protect disconnected fiber-optic connectors. When

protective covers are not in use, store them in a clean container. Do not store

protective covers in clothes pocket.

...................................................................................................................................................................................................

1 Use optical power meter to determine if light is coming out of fiber-optic connector.

...................................................................................................................................................................................................

2 Did optical power meter detect light coming out of fiber-optic connector?

If yes, find the source and disconnect it.

...................................................................................................................................................................................................

3 Use the inspection microscope to inspect the fiber-optic connector. See Figure A-1,

“Fiber-optic connector inspection” (p. A-4) for examples of clean and contaminated

fibers.

Use the following criteria to determine clean fiber:

1. Fiber core must have no contaminants or defects.

2. Fiber cladding must have no contaminants. Minor defects (pits and scratches) are

acceptable.

3. Fiber ferrule must not have contaminants or defects that interfere with fiber-optic

connector mating.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-3

...................................................................................................................................................................................................

4 Is fiber-optic connector clean?

If yes, proceed to Step 12.

If no, proceed to Step 5.

Figure A-1 Fiber-optic connector inspection


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

5 Holding CLETOP fiber-optic cleaner with one hand, use metal lever to open metal slide

and expose cleaning surface. Do not release lever.

...................................................................................................................................................................................................

6 Place fiber ferrule firmly against CLETOP fiber-optic cleaner cleaning surface, rotate

ferrule 90 degrees, then swipe ferrule along cleaning surface one time in one direction

only.

...................................................................................................................................................................................................

7 Release metal lever.

...................................................................................................................................................................................................

8 Use inspection microscope to inspect fiber-optic connector. See Figure A-1, “Fiber-optic

connector inspection” (p. A-4) for examples of clean and contaminated fibers. Use the

following criteria to determine clean fiber:

• Fiber core must have no contaminants or defects.

• Fiber cladding must have no contaminants. Minor defects (pits and scratches) are

acceptable.

• Fiber ferrule must not have contaminants or defects that interfere with fiber-optic

connector mating.

...................................................................................................................................................................................................

9 Is the fiber-optic connector clean?

If yes, go to Step 12.

If no, go to Step 10.

...................................................................................................................................................................................................

10 Clean and inspect the fiber-optic connector up to five more times.

...................................................................................................................................................................................................

11 Is the fiber-optic connector clean?


If no, connector may need to be replaced.

...................................................................................................................................................................................................

12 Are there more fiber-optic connectors to clean?

If yes, refer back to Step 1.


...................................................................................................................................................................................................

13 STOP! This procedure is complete.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-5

E N D O F S T E P S...................................................................................................................................................................................................

Cables, connectors, and assemblies

Purpose

This section provides details on cables and cable assemblies available for the

Alcatel-Lucent 1646 SMC Release 2.1 Installation and System Turn-Up GuideTal.

Contents

This section covers the following:

• “Cable product codes” (p. A-6)

• “Board connector pin assignment and corresponding cable” (p. A-6)

• “Cable information” (p. A-12)

Cable product codes

Cable Product Code

21*2M*75Ohm*5M cable 3KC180120005

21*2M*75Ohm*10M cable 3KC180120010

21*2M*75Ohm*15M cable 3KC180120015

21*2M*75Ohm*20M cable 3KC180120020

21*2M*120Ohm*5M cable 3KC180130005

21*2M*120Ohm*10M cable 3KC180130010

21*2M*120Ohm*15M cable 3KC180130015

21*2M*120Ohm*20M cable 3KC180130020

RJ45 Cable (other side open) 3KC18009AAAA

Ethernet cable 3KC18010AAAA

E3/T3 Cable (30M) 3KC18014AAAA

DC -48V Power cable (3M) 3KC18015AAAA

AC 220V Power cable (3M) 3KC18016AAAA

1646SMC Debug cable 3KC18114AAAA

3KC18100AAAA 120OHM TO 75OHM CONVERSION CABLE

3KC18101AAAA 1646SM/C SUBRACK GROUNDING CABLE

Board connector pin assignment and corresponding cable

This section provides board connector pin assignment and corresponding cable details.

Miscellaneous references Cables, connectors, and assemblies

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



MB16P

Table A-1 RJ-45 connector pin assignment and cable

Front Panel RJ-45 PIN Description Cable product code

SYNC/EOW 1 NC 3KC18009AAAA

(RJ45 cable, other side

open)

2 NC

3 External clock input(+)

4 EOW signal (not used)

5 EOW signal (not used)

6 External clock input(-)

7 External clock output(+)

8 External clock output(-)

Figure A-2 RJ-45 connector front view, including SYNC/EOW, F2/DBG, HK, LAN,

FE1~4 and FE 5~8

Figure A-3 RJ-45 connector


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-7

Table A-1 RJ-45 connector pin assignment and cable (continued)


F2/DBG 1 DTR for modem(not used) 3KC18114AAAA

(1646SMC Debug cable)2 F2 receive signal(not used)

3 F2 transmit signal(not used)

4 GND

5 X.25 receive signal(not

used)

6 X.25 transmit signal(not

used)

7 DBG_L receive signal

8 DBG_L transmit signal

HK 1 HK input1(+) 3KC18009AAAA

(RJ45 Cable, other side

open)

2 HK input1(-)

3 HK input2(+)

4 HK input2(-)

5 HK input3(+)

6 HK input3(-)

7 HK output(+)

8 HK output(-)

LAN 1 Transmit signal (+) 3KC18010AAAA

(Ethernet cable)2 Transmit signal (-)

3 Receive signal (+)

4 NC

5 NC

6 Receive signal (-)

7 NC

8 NC

FE Interface

(1~4, 5~8)

1 Transmit signal (+) 3KC18010AAAA



4 GND

5 GND


7 GND

8 GND


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Two E1/T1 interface types are supported: 75Ohm and 120Ohm with different pin

definition and cable

• MB16A and MB16B: 120Ohm E1/T1

• MB16C and MB16D: 75Ohm E1/T1

Figure A-4 E1/T1 connector ANEA96 front view


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-9


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



PE1A/B

Front Panel

Interface

PIN Description Cable product code

PE1A

2 x ANEA96

Same as MB16A/B 3KC180130005

3KC180130010

3KC180130015

3KC180130020

(21*2M*120Ohm cable)

PE1B

2 x ANEA96

Same as MB16C/D 3KC180120005

3KC180120010

3KC180120015

3KC180120020

(21*2M*75Ohm cable)


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-11

P8FES


FE Interface

(1~8)

1 Transmit signal (+) 3KC18010AAAA



4 GND

5 GND


7 GND

8 GND

P3E3

Front Panel coaxial

connector

Description Cable product code

1~3 IN

1~3 OUT

Coaxial connector 3KC18014AAAA

(E3/T3 cable 30m)

Cable information

Note: Connector pin with same number on both cable and board will be connected

together when assembly.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Ethernet cable (3KC18010AAAA)

X1 RJ-45 X2 RJ-45 Color Relation

1 1 White/Green PAIR

2 2 Green

3 3 White/Orange PAIR

4 4 Orange

5 5 Blue PAIR

6 6 White/Blue

7 7 White/Brown PAIR

8 8 Brown

RJ45 Cable, other side open (3KC18009AAAA)

X1 RJ-45 Color Relation

1 Blue PAIR

2 White

3 Orange PAIR

4 White

5 Green PAIR

6 White

7 Brown PAIR

8 White


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-13

21*2M*75Ohm cable (3KC180120005, 3KC180120010, 3KC180120015,

3KC180120020)


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Note: STARTPT parameter example X1.38, X1 means Anea96 connector, 38 means

pin number


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-15

21*2M*120Ohm cable (3KC180130005, 3KC180130010, 3KC180130015,

3KC180130020)


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Note: STARTPT parameter example X1.38, X1 means Anea96 connector, 38 means

pin number.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-17

1646SMC Debug cable (3KC18114AAAA)


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Cable assembling instruction

Before you begin

This section describes how to assemble the SMB-75K4C3. The process shown below is

based on a typical E3 coaxial connector. The process in field may be different, if a

different coaxial connector is used.

Steps

...................................................................................................................................................................................................

1 The typical structure of E3 connector is shown in the following figure. A crimp tool is

necessary to complete the termination.

Figure A-5 Crimp ferrule

Miscellaneous references Cable assembling instruction

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-19

...................................................................................................................................................................................................

2 Strip the cable inner conductor, dielectric, drain wire, braid/AL-PET tape and jacket as

per “Recommended cable stripping detail” in the figure. Be careful not to damage the

braid, drain wire and inner conductor. Do not nick braid, drain wire and inner conductor

of cable.

Figure A-6 Crimp tool


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

3 Insert the inner conductor into conductor PIN as show. Make sure the inner conductor of

cable is visible inside hole of conductor PIN. Crimp it with the crimp tool. Then slide the

ferrule onto the cable and flair braid to facilitate insertion of body.

...................................................................................................................................................................................................

4 Put on and slide the ferrule to the cable as shown in following figure. Then insert rear

post of connector main body between the dielectric and braid (included drain wire and

AL-PET tape)

Figure A-7 Dimensions of cable stripping


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-21

...................................................................................................................................................................................................

5 Dress braid and AL-PET tape evenly around rear post. Slide ferrule over braid until it

rests flush against main body.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC




....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-23

E N D O F S T E P S...................................................................................................................................................................................................

Install FTP server

Description

File Transfer Protocol (FTP) services should be installed and administered by the local

customer organization responsible for workstation operations. Follow customer

guidelines.

This procedure can be used to determine if FTP service is running, install generic

Microsoft 2000 Professional, Internet Information Services (ISS) and/or configure a

generic FTP service. Customer guidelines can vary. Consult appropriate local

organization before installing any Microsoft products.

Procedure

...................................................................................................................................................................................................

1 Is there currently a Microsoft FTP server set up on the local machine?


If unsure, proceed to Step 3.


...................................................................................................................................................................................................

2 Is the Local Path information known?



...................................................................................................................................................................................................

3 Note: Check if Microsoft FTP server is installed:

To open the Control Panel, select Start > Settings > Control Panel.

...................................................................................................................................................................................................

4 Double-click the Administrative Tools icon.

...................................................................................................................................................................................................

5 Double-click the Computer Management icon.

...................................................................................................................................................................................................

6 In the Computer Management window, expand the Services and Applications node.

...................................................................................................................................................................................................

7 Is Internet Information Services listed?


If no, there is currently no FTP server installed. Close the Computer Management

window and proceed to Step 18.

Miscellaneous references Install FTP server

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

8 Select Internet Information Services.

...................................................................................................................................................................................................

9 Is an FTP site listed in the details window?



...................................................................................................................................................................................................

10 FTP server is set up on local machine. Is current FTP site to be configured with the

Alcatel Lucent default configuration?



...................................................................................................................................................................................................

11 Right-click the FTP site and select Properties.

...................................................................................................................................................................................................

12 Select the Home Directory tab.

...................................................................................................................................................................................................

13 Write down the value entered for the Local Path for future use.

...................................................................................................................................................................................................

14 Verify the Read and Write boxes are checked.

...................................................................................................................................................................................................

15 Click OK.

...................................................................................................................................................................................................

16 Close the Computer Management window.

...................................................................................................................................................................................................

17 Proceed to Step 43.

...................................................................................................................................................................................................

18 Note: Install Microsoft®

FTP server software:


...................................................................................................................................................................................................

19 Double-click Add/Remove Programs.

...................................................................................................................................................................................................

20 On the left side of the Add/Remove Programs window, select Add/Remove Windows

Components.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-25

...................................................................................................................................................................................................

21 In the Add/Remove Windows Components window, highlight Internet Information

Services (IIS) and click the Details... button.

...................................................................................................................................................................................................

22 Select the File Transfer Protocol (FTP) Server/Service checkbox.

...................................................................................................................................................................................................

23 Click OK.

...................................................................................................................................................................................................

24 In the Windows Components window, click Next to initiate the installation.

...................................................................................................................................................................................................

25 As the installation continues, the user may be asked to provide Windows Media. Either

insert the disk or browse to location of files.

...................................................................................................................................................................................................

26 In the completion window, click Finish.

...................................................................................................................................................................................................

27 Close the Add/Remove Programs window.

...................................................................................................................................................................................................

28 Note: To configure FTP Site:

Open the Control Panel. Select Start > Settings > Control Panel.

...................................................................................................................................................................................................

29 Double-click on the Administrative Tools icon.

...................................................................................................................................................................................................

30 Double-click on the Computer Management icon.

...................................................................................................................................................................................................

31 In the Computer Management window, expand the Services and Applications node.

...................................................................................................................................................................................................

32 Select the Internet Information Services node.

...................................................................................................................................................................................................

33 Right-click Default FTP Site in the details window and select Properties.

...................................................................................................................................................................................................

34 Select the Security Accounts tab.

...................................................................................................................................................................................................

35 Uncheck the Allow Anonymous Connections box.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

36 If prompted, click Yes in the confirmation window.

...................................................................................................................................................................................................

37 Select the Home Directory tab.

...................................................................................................................................................................................................

38 Under the FTP Site Directory pane, set the Local Path to where the NE database backups

and NE generic software is to be stored.

The Alcatel-Lucent preferred path is: C:/ALCATEL-LUCENT

Note: If selecting a different directory, note the location for future use.

Note: If input to set Local Path is not active, reboot PC to activate.

...................................................................................................................................................................................................

39 Verify that the Read and Write check boxes are selected.

...................................................................................................................................................................................................

40 Click OK.

...................................................................................................................................................................................................

41 Close the Computer Management window.

...................................................................................................................................................................................................

42 Close the Administrative Tools window.

...................................................................................................................................................................................................

43 Note: To configure FTP user account:


...................................................................................................................................................................................................

44 Double-click Users and Passwords. (For Windows XP, double-click User Accounts)

...................................................................................................................................................................................................

45 In the Users and Passwords/User Accounts window, select the Advanced tab.

...................................................................................................................................................................................................

46 Under Advanced User Management, click the Advanced button.

...................................................................................................................................................................................................

47 Right-click the Users node and select New User...

...................................................................................................................................................................................................

48 Enter the name gemftp for the username.

...................................................................................................................................................................................................

49 Enter and confirm password.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-27

Note: Record this password for future reference and protect it to prevent unauthorized

use.

...................................................................................................................................................................................................

50 Uncheck: User must change password at next login box.

...................................................................................................................................................................................................

51 Check the User cannot change password and Password never expires boxes.

...................................................................................................................................................................................................

52 Click Create.

...................................................................................................................................................................................................

53 Click Close.

...................................................................................................................................................................................................

54 Close the Local Users and Groups window.

...................................................................................................................................................................................................

55 In the Users and Passwords/User Accounts window, click OK.

...................................................................................................................................................................................................

56 Is PC running Windows XP Service Pack 2?



...................................................................................................................................................................................................

57 Note: To create exception for FTP port:


...................................................................................................................................................................................................

58 Double-click the Windows Firewall icon.

...................................................................................................................................................................................................

59 Click the Exceptions tab.

...................................................................................................................................................................................................

60 Click the Add Port... button.

...................................................................................................................................................................................................

61 In the name field, enter FTP.

...................................................................................................................................................................................................

62 In the Port number field, enter 21.

...................................................................................................................................................................................................

63 Click OK.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



...................................................................................................................................................................................................

64 Click OK to close the Windows Firewall box.

...................................................................................................................................................................................................

65 STOP! This procedure is complete.


....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





A-29

E N D O F S T E P S...................................................................................................................................................................................................

List of SFPs

The following table lists the SFPs for the Alcatel-Lucent 1646 SMC.

Table A-2 List of SFPs

Part Number Description Category

1AB196340009 CWDM 1470NM PIN SFP DDM EL/OPT MODULES








1AB196350026 CWDM 1470NM APD SFP DDM EL/OPT MODULES








1AB210170001 EL TRX SFP STM-1EL EL/OPT MODULES

1AB376350001 ALU SFP S-1.1 -40/+85 EL/OPT MODULES

1AB376350002 ALU SFP L-1.1 -40/+85 EL/OPT MODULES





1AB376370001 ALU SFP I-16.1 -40/+85 EL/OPT MODULES




1AB376720001 ALU SFP GBE SX -40/+85 EL/OPT MODULES

1AB376720002 ALU SFP GBE LX -40/+85 EL/OPT MODULES

1AB376720003 ALU SFP GBE ZX -40/+85 EL/OPT MODULES

Miscellaneous references List of SFPs

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Glossary

...................................................................................................................................................................................................................................

A ACO

Alarm Cut Off

AFI

Authority and Format Identifier

AIS

Alarm Indication Signal

AS

Alarm Surveillance

ASAP

Alarm Severity Assignment Profile

ATTD

Attended (Alarm Storing)

...................................................................................................................................................................................................................................

B B&W

Black and White

...................................................................................................................................................................................................................................

C CD

Current Data

CD-ROM

Compact Disk Read Only Memory

Ch

Channel

CLEI

Common Language Equipment Identification

CLNP

Connection-Less Network Protocol

....................................................................................................................................................................................................................................

1646 SMC





GL-1

CO

Centre Office

CPE

Customer Premise Equipment

CSF

Client Signal Fail

CT

Craft Terminal

CWDM

Coarse Wavelength Division Multiplexing

...................................................................................................................................................................................................................................

D DB

Database

DCC

Data Communication Channel

DCN

Data Communication network

DDM

Digital Diagnostic Monitoring

DMUX

Demultiplexing

DWDM

Dense Wavelength Division Multiplexing

...................................................................................................................................................................................................................................

E E-SNCP

Electrical SubNetwork Connection Protection

EC

Equipment Controller

ECT

Equipment Craft Terminal

EEPROM

Electrically Erasable Programmable Read Only Memory

EMC

Electromagnetic Compatibility

ESC-LC

Low Cost Equipment and Shelf Controller

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

GL-2 Alcatel-Lucent – Proprietary


1646 SMC



ESD

Electrostatic Discharges

...................................................................................................................................................................................................................................

F FPGA

Field Programmable Gate Array

...................................................................................................................................................................................................................................

G Gbit/s

Giga bit per second

GOSIP

Government Open System Interconnection Profile

...................................................................................................................................................................................................................................

H HD

History Data

HDBK

Handbook

HDLC

High Level Data Link Control

HK

Housekeeping

HW

Hardware

...................................................................................................................................................................................................................................

I I/O

Input/Output

IEC

International Electro-technical Commission

ILOS

Input Loss of Signal

IND

Indeterminate

IP

Internet Protocol

IS-IS

Intermediate System-to-Intermediate System

ISO

International Standard Organization

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





GL-3

ISSB

Intra Shelf Serial Bus

ITU-T

International Telecommunication Union -Telecommunication

...................................................................................................................................................................................................................................

L LAN

Local Area Network

LAPD

Link Access Protocol D-Channel

LAT

Lamp Test

LED

Light Emitting Diode

LOC

Loss of Clock

...................................................................................................................................................................................................................................

M MAC

Medium Access Control

...................................................................................................................................................................................................................................

N NE

Network Element

NES

Network Element Synthesis

NSAP

Network Service Access Point

NTP

Network Time Protocol

NURG

Not Urgent

...................................................................................................................................................................................................................................

O O-SNCP

Optical SubNetwork Connection Protection

OAD

Optical Add and Drop

OADM

Optical Add and Drop Multiplexer

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



OCH

Optical Channel

OMDX

Optical Multiplexer and Demultiplexer

OMSP

Optical Multiplex Section Protection

OS

Operation System

OSC

Optical Supervisory Channel

OSI

Open System Interface

OSPF

Open Shortest Path First

...................................................................................................................................................................................................................................

P PC

Personal Computer

PCB

Printed Circuit Board

PDU

Power Distribution Unit

PI

Physical Interface

PSC

Power Supply Card

...................................................................................................................................................................................................................................

Q Q3

Interface with Protocol Q3

...................................................................................................................................................................................................................................

R RAM

Random Access Memory

RDI

Remote Defect Indication

RI

Remote Inventory

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





GL-5

RS

Regenerator Section

RX

Receiver

...................................................................................................................................................................................................................................

S SC

Shelf Controller

SD

Shutdown

SDH

Synchronous Digital Hierarchy

SNCP

Sub-Network Connection Protection

SNMP

Simple Network Management Protocol

SPI

Serial Peripheral Interface

SSF

Server Signal Fail

SSFe

Server Signal Fail Egressing

SSFi

Server Signal Fail Ingressing

SWDL

Software Download

SWP

Software Product

...................................................................................................................................................................................................................................

T TCP/IP

Transmission Control Protocol/Internet Protocol

TMN

Telecommunication Management Network

TP

Termination Point

TSF

Trail Signal Fail

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



TX

Transmitter

...................................................................................................................................................................................................................................

U URU

Underlying Resource Unavailable

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

1646 SMC





GL-7

Glossary

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................



1646 SMC



Index

A alarm cables, 4-6

.............................................................

C cable installation, 4-1

card

alignment, 1-15

extraction, 1-15

.............................................................

D documentation set, x

.............................................................

E electrostatic discharge, 1-9

.............................................................

F fiber

cleaning procedure, A-3

installation, 4-1

fiber optic cleaning, A-2

.............................................................

G general safety, 1-14

.............................................................

H hazard level assignment, 1-5

.............................................................

I IEC requirements, 1-4

installation

FTP server, A-24

.............................................................

L laser

classes, 1-5

product classification, 1-4

safety, 1-6

safety instructions, 1-8

warning label, 1-6

.............................................................

O optical telecommunication

equipment, 1-5

.............................................................

P physical installation, 3-1

Caution to avoid Equipment

damage, 3-2

power installation, 4-1

.............................................................

S safety

laser product, 1-4

structure, 1-1

signal transmission cables, 4-8

special tools, 2-4

standard compliance, 1-4

system design, 1-6

.............................................................

T test equipment, 2-4

....................................................................................................................................................................................................................................

1646 SMC





IN-1

Index

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

IN-2 Alcatel-Lucent – Proprietary


1646 SMC



Documents

3KC18037ABABTQZZA_V1_Alcatel-Lucent 1646 Synchronous Multiplexer Compact Release 2.1 Installation and System Turn-Up Guide