MOSHELL NOTES – HOW TOTo check pm counters for E1

In RXI pr atmport=ms-x-y get <proxy> lpget Subrack=MS,Slot=x,PlugInUnit=1,Etm1=1,E1PhysPathTerm=ppy

To check E1-MS port in RXI (add E1 for RBS)

In RNC st <sitename> get <proxy> iub

In RXI pr .<iub> eg. pr .0095 lk <proxy> st atmport=ms-x-y bl lget ms-2-2 (then check iub number with STR printout – see tally or not) reservedBy Aal2PathVccTp=b0001a2 <----- iub # = 0001

In RBS (when port is ready but E1 not pull through yet – so that no alarm) pr atmport get <proxy> ie. get 1345 lget Subrack=1,Slot=2,PlugInUnit=1,Etm1=1,E1PhysPathTerm=pp2

set <proxy> administrativeState 0 (to lock the 2nd physical port)

set 194 administrativeState 0 (to lock the 2nd physical port)

To remove Utrancell & IubLink in RNC

lst <utrancell> eg. lst raza lst singmu ldel <utrancell>

lst .b<iub-no> eg. lst .b0095 (WARNING : Check other proxys) ldel .<iub-no> (WARNING : Exclude other proxys)

RNCTGEM01> lst .b14 Around 12 MOs for IUB (1E1) 060105-12:32:30 ======================================================================

============= Proxy Adm State Op. State MO ======================================================================

============= 3517 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b14ib 3518 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b14ia 3586 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b14db 3587 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b14da 3590 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b14cb 3591 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b14ca 3751 0 (DISABLED) TransportNetwork=1,Aal0TpVccTp=b14sb1 3761 0 (DISABLED) TransportNetwork=1,Aal0TpVccTp=b14sa1 4314 0 (DISABLED) TransportNetwork=1,UniSaalTp=b14db 4316 0 (DISABLED) TransportNetwork=1,UniSaalTp=b14da 4319 0 (DISABLED) TransportNetwork=1,UniSaalTp=b14cb 4320 0 (DISABLED) TransportNetwork=1,UniSaalTp=b14ca ======================================================================

============= Total: 12 MOs

lst .vc<iub-no> eg. lst .vc95 (WARNING : Check other proxys) ldel .vc<iub-no> (WARNING : Exclude other proxys) RNCTGEM01> lst .vc14 Around 10 MOs for IUB (1E1) 060105-12:30:49 ======================================================================

============= Proxy Adm State Op. State MO ======================================================================

============= 2972 1 (ENABLED) TransportNetwork=1,AtmPort=MS-26-1,VplTp=vp1,VpcTp=1,VclTp=vc1437 2973 1 (ENABLED) TransportNetwork=1,AtmPort=MS-26-1,VplTp=vp1,VpcTp=1,VclTp=vc1436 2974 1 (ENABLED) TransportNetwork=1,AtmPort=MS-26-1,VplTp=vp1,VpcTp=1,VclTp=vc1435 2975 1 (ENABLED) TransportNetwork=1,AtmPort=MS-26-1,VplTp=vp1,VpcTp=1,VclTp=vc1434 2976 1 (ENABLED) TransportNetwork=1,AtmPort=MS-26-1,VplTp=vp1,VpcTp=1,VclTp=vc1432 3978 1 (ENABLED) TransportNetwork=1,AtmPort=MS-7-1,VplTp=vp1,VpcTp=1,VclTp=vc1432 4187 1 (ENABLED) TransportNetwork=1,AtmPort=MS-6-1,VplTp=vp1,VpcTp=1,VclTp=vc1432 4484 1 (ENABLED) TransportNetwork=1,AtmPort=MS-27-1,VplTp=vp1,VpcTp=1,VclTp=vc1444 4485 1 (ENABLED) TransportNetwork=1,AtmPort=MS-27-1,VplTp=vp1,VpcTp=1,VclTp=vc1443 4487 1 (ENABLED) TransportNetwork=1,AtmPort=MS-27-1,VplTp=vp1,VpcTp=1,VclTp=vc1433 ======================================================================

============= Total: 10 MOs

From RNCs delete external utran relations lpr utranrelation=<sitename> ldel utranrelation=<sitename>

To remove rbs in RXI

pr .b<iub-no> lk <proxy>

pr aal2routingcase 6012200500<rncid><iub-no> del <proxy> lst .b<iub-no> eg. lst .b0095 ldel .b<iub-no>

lpr atmport=ms-18-1 lget atmport=ms-18-1 del <proxydown>-<proxytop-1> WARNING : Don’t remove the MS port

del AtmPort=MS-20-1-* (to delete the whole 63 ports of the ETMC41)

lst Slot=18.*Vc12Ttp=1 or to block all ports : lbl Slot=18.*Vc12Ttp=*

lpr vc<iub> eg. lpr vc95 ldel vc<iub> eg. ldel vc95 (WARNING : Exclude other VCs)

To remove rbs in ATMCC

lst .b<iub-no> eg. lst .b0095 ldel .b<iub-no>

lpr vc<iub> eg. lpr vc95 ldel vc<iub> eg. ldel vc95 (WARNING : Exclude other VCs)

To check pm (performance) counters in RNC/RXI

get 1 (to see the performance directory) ls -l /p001200/pm/ | grep xml (to see the performance files)

pst (list the scanners, status) pmr [-m 5 –p 3] (get performance report) [for the last 5 hours + 3 ]

To create performance counters scanner

pst pgetsn <proxy> pcr <name> <mo-name> <counter-name> eg. pcr <rssi> cellcarrier pmAverageRssi pget <mo-name> <counter-name> to read the counters pbl/pdeb <proxy> to stop/resume scanner pdel <proxy> to delete scanner

To set SAC in Utrancell

pr utrancell=ower serviceAreaRef (then) get utrancell=ower serviceAreaRef set utrancell=AMGMMU servicearearef LocationArea=1,servicearea=12 (SAC defined)

To set Electrical Tilt (RET)

pr retdevice get <proxy> set <proxy> electricalAntennaTilt <value> get ret electrical

To set Latitude/Longitude

get sector lat set sector latitude <value>

To log alarm in a nice format

lgevsm

Sample Scripts in moshell

for 10Enter commmands (one per line), then type "done"> get radiolink num> wait 2> done

To enable E1 supervision

set

To create Group (eg. Not reserved VclTp)

get vcltp reservedby !.*= lma <group-name> vcltp reservedby !.*=

To create performance counters

pst

To check cell state

In RNC lst utrancell st utrancell 1.*0 (cells Unlocked & Disabled)

To check RBS MO

In RBS st plug (AuxPlugInUnit=2 is the RET, AuxPlugInUnit=1 is the ASC) cabx cab (without the external parts)

To change PSC (

In RNC st plug (AuxPlugInUnit=2 is the RET, AuxPlugInUnit=1 is the ASC) cabx cab (without the external parts)

To change SAC (Service Area Code)

In RNC Pr cell Get proxy Get set utrancell=KCC1BU servicearearef LocationArea=1,servicearea=284

To change maxtxpowerdl for specific cell (usually to clear CONGESTION alarms)

In RNC get CUV1BU_1 maxtxpowerdl --> in EMAS, click Utrancell, Properties, Cell (PCIPCH in Common Channel) set CUV1BU_1 maxtxpowerdl 402 maxtxpowerdl value stated as x10dBm (actual = 0.1x) maxtxpowerdl value usually 0.4 dBm lesser than maxDlPowerCapability (from RBS) thus if maxDlPowerCapability 422, maxtxpowerdl 418 (422 – 4)

in P3 - get SOGXBU_1 maximumtransmissionpower

To lock/unlock cells

In RNC st utrancell=sunwmu lst sunw lbl sunw (to lock cell & channels) bl sunw (to lock cell only) deb sunw (to unlock)

To check RBS info

In RBS Get 0 Get 1 (check ntpServerAddressPrimary)

To check network clock synchronisation

In RNC & RBS Read clock (GMT +8) ntpconfig info Check which OMNIFSERVER the node is connected to (i.e ntpServerAddressPrimary) – from get 1

To check atmport & pp (physical port)

In RBS lpr atmport vc32&33 for signaling lpget 1007 (vc proxy) – to see number of ATM traffic cells transferred get atmport=1-2-2 then : lget Subrack=1,Slot=2,PlugInUnit=1,Etm1=1,E1PhysPathTerm=pp2 to un/lock have to set values 1 or 0

To administer state of Mos

In RBS St plug Deb proxy Bl proxy No need to use set 1 or set 0 (only for physical ports) otherwise use deb & bl

To autocreateCV

In RNC & RBS Get config Cv ls (2 CVs will be used for the autocreate CV function) Set “proxy” autoCreatedCVIsTurnedOn true/false Set timeForAutoCreatedCV (UTC time) Set timeForAutoCreatedCV 13:00 (cv autocreated at 9pm)

To check SAC corruption

In RNC tg | grep -i kcc1bu lh mod1 cell get 1/1/1/1/2/1.44 cellData lookout for , sac int 10 } which states a wrong SAC value for the Utrancell get utrancell=kcc1bu cid (cid = SAC + sector number) get serviceArea=284 to confirm SAC for the cell

To any hanging modules

In RNC only stdh

To restart Node

In RNC,RXI & RBS acc 0 restart poll (to wait 20seconds until node comes up again)

To create CV

In RNC,RXI & RBS cvms CXP9010373%1_R11G_050725_1516 emfauzi change_ntpserver_ip cvms CXP9010373%1_R11G_050725_1516 followed by comments for the CV cvset CXP9010373%1_R11G -- to set the CV startable

To change LAC (Location Area Code)

In RNC get servicearea=132 get locationarea get routingarea get externalutrancell LAC --> corresponding LAC changed at neighbour RNC (if defined) set ExternalUtranCell=uefaMU_1 lac 12050 -->to change the externalutrancell LAC parameter for the

particular cell at another/neighbour RNC get utrancell=uefa lac --> to view externalutrancell LAC parameter at neighbour RNC get utrancell=cinoMU_3

To restart node

In RNC & node B acc 0 restart pol - to get moshell connected once node has restarted

To check plugin status

In RNC & node B st plugin st plugin 1 0 st plugin 0 1 lst plug 0

To enter Moshell with security enabled

In RNC & node B moshell -c host.p12 10.78.37.225

To block sectors via Moshell

In RNC St blip Bl the proxy Deb the proxy (can have multiple proxies for more cells)

To view delay & attenuation parameters within a sector

In RBS Get jumper Get feeder Get rbs xdl

To delete something already done with a script

In RNC/RXI/RBS First you have to generate the MO Delete script

This is done by ./undomo add2nde1inrxi_PUJMMU.mo > pujmrxibesi01.mo [~]$ ./undomo add2nde1inrxi_PUJMMU.mo > pujmrxibesi01.mo [~]$

Where add2nde1inrxi_PUJMMU.mo is the script which was run earlier

And pujmrxibesi01.mo is the Delete Script

Modify add2nde1inrxi_PUJMMU.mo so that downtime will be less

Run pujmrxibesi01.mo to undo the wrongly defined MO

Then run the modified/correct add2nde1inrxi_PUJMMU.mo

To check E1 state

In RXI St ms-20-2 Check whether port locked or not pr the port number pr pp(port#)

Pr pp2 or pp7 (ETM1)

lst Slot=8.*Vc12Ttp=5$ (ETMC41, MS-8-5)

Get proxy and view admin state whether locked or not Then do deblocking Deb proxy St proxy

Make sure port is deblocked (can also see in EMAS)

In RBS St atmport Check port lock state

St pp St pp2 st pp3 st pp4

To check locked board in node

In all nodes lst plug 0

To restart / reload board

In all nodes Acc 000900 restart Acc 001400 reload

GSG – get set get

In RNC To activate type gsg To deactivate type gsg again Use run command (not trun)

run and trun

In all nodes trun is only for xml scripts

run for scripts such as set DAGAMU_1 usedFreqThresh2dEcno -12

trun for running the last script : rbs_EQINMU_site_complete.mo run is for any script (txt for for example)

open logfile l+ 20060113_CR003_RNCTGEM01.log cannot have undo mode while having gsg activated run CR003_13012006.txt close logfile

CAB printout 0 = slot 28, 1 = slot 1

In all nodes

RXIKPNG02> cab

060206-11:09:22.......=====================================================================================================SMN APN BOARD GREEN YELLOW RED PRODUCT NR REV DATE SERIAL NR TEMP COREMGR===================================================================================================== 0 1 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20050608 TU86364489 0 2 HUB MP ON OFF OFF ROJ 119 2106/40 R5A 20050626 TU86494707 +32C Active 0 3 GPB40 ON OFF OFF ROJ 119 2106/40 R5A 20050626 TU86494699 +31C StandbyReady 0 4 TUB ON OFF OFF ROJ 119 2104/4 R3B 20050620 TU86442436 0 5 TUB ON OFF OFF ROJ 119 2104/4 R3B 20050620 TU86442439 0 8 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644146 0 10 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644042 0 12 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644052 0 14 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644056 0 16 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644037 0 18 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU86644067 0 20 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050708 TU86592867 0 24 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86545997 0 25 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86545998 0 26 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86545996 0 27 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU86546001 0 0 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20050608 TU86364157 -----------------------------------------------------------------------------------------------------

1 is slot 10 is slot 28

primary ScramblingCode

In RNC get iska primaryscram

maxDlPowerCapability /maxDlIn RBS

get local xdlIn RBS

get SOGXBU_1 maximumtransmissionpower

redefine TD in VC

In RXI Resources for CELL does not come up – apparently TD is defined as U42 lget AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc39 lrset AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc39 atmTrafficDescriptorId AtmTrafficDescriptor=C2P4000

Check E1 loop

In node

lacc AtmPort=MS-27-1,VplTp=vp5 eteloopback

Check 101 or not

In node RNC & ATMCC only Pr vc21432 Pr vc*RBSID*32

LST carrier

KIRAMU> lst carrier

060303-10:58:44===================================================================================Proxy Adm State Op. State MO===================================================================================1208 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=11210 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Ssch=11211 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Psch=11212 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Pcpich=11213 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Pccpch=11214 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Pccpch=1,Bch=11215 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Prach=11216 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Prach=1,Rach=11217 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Aich=11218 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Sccpch=21219 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Sccpch=2,Fach=11220 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Sccpch=2,Fach=21221 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Sccpch=11222 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Sccpch=1,Pch=11223 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1,Pich=11225 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=11227 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Ssch=11228 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Psch=11229 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pcpich=11230 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pccpch=11231 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pccpch=1,Bch=11232 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Prach=11233 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Prach=1,Rach=11234 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Aich=11235 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=21236 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=2,Fach=11237 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=2,Fach=21238 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=11239 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=1,Pch=11240 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pich=1

1242 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=11244 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Ssch=11245 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Psch=11246 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pcpich=11247 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pccpch=11248 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pccpch=1,Bch=11249 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=21250 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=2,Fach=11251 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=2,Fach=21252 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=11253 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=1,Pch=11254 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pich=11255 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Prach=11256 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Prach=1,Rach=11257 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Aich=1===================================================================================Total: 45 MOs - for fully operational site

OSSRC IP address 10.125.7.103telnet the IP address before the main RBS IP

To Check E1 from RNC then RXIIn node RNC

pr iub pot3 to get RBSID or Pr iub *RBSID* Get the proxy for the Aal0 - look for the name

In node RXI pr .124

Utrancell RelationsIn node RNC

lpr utrancell=evermu_2 utranrelation

IUB for utrancell definitionIn node RNC

st utrancell=MC get 10545 iub

ATM port from RNCIn node RNC

Must know the RBS ID 1st get aal2pathvcctp=b0016

Check Error countIn node RXI

Pget <proxy>

Check VP1 or VP101In node RNC

Get .vc209

=================================================================================================================5576 TransportNetwork=1,AtmPort=MS-7-1,VplTp=vp101,VpcTp=1,VclTp=vc20932=================================================================================================================VclTpId vc20932atmTrafficDescriptorId AtmTrafficDescriptor=U4availabilityStatus 0 (NO_STATUS)externalVci 20932operationalState 1 (ENABLED)reservedBy AtmCrossConnection=b209ibuserLabel =================================================================================================================5848 TransportNetwork=1,AtmPort=MS-6-1,VplTp=vp101,VpcTp=1,VclTp=vc20932=================================================================================================================VclTpId vc20932atmTrafficDescriptorId AtmTrafficDescriptor=U4availabilityStatus 0 (NO_STATUS)externalVci 20932operationalState 1 (ENABLED)reservedBy AtmCrossConnection=b209iauserLabel =================================================================================================================Total: 10 MOs

Check security turn ON in RBS or NOTIn node RNC

Lt manage

To change all gsmrelation in the NodeIn node RNC

set GsmRelation qOffset1sn 1 (1 means 1 db) mom gsmrelation qoffset

To change gsmrelation of only some cellsIn node RNC

lset UtranCell=CHERMU_1,GsmRelation=RANEM1_2 qOffset1sn 7 (7 means 7 db)

To check what is in the RNCMODULEIn node RNC

Lt rncmodule Get rncmodule Pr rncmodule (then get proxy oso can)

To check how many HSDPA users in a cell (must know CID)In node RNC

dyncelldata cid 02301

RNCKPNG01> dyncelldata cid 02301

060425-10:51:23Trying password from ipdatabase file: /home/emfauzi/moshell/sitefiles/ipdatabase...$ dyncelldata cid 02301cId: 2301Cell froId: 65CC SP: 011000/sp0.lnh/CommonChMainPTrncModuleId: 4IubLink froId: 22Total ASE DL: 944aseDlAdm: 240beMarginAseDl: 100Total ASE UL: 16748aseUlAdm: 500aseUlAdmOffset: 40beMarginAseUl: 0CPM RL Count: 0compModeAdm: 15HSDPA UE Count: 5 <------------------------- 5 user currentlyhsdpaUsersAdm: 20SF8 RL DL Count: 0sf8Adm: 1SF16 RL DL Count: 0sf16Adm: 16SF32 RL DL Count: 0sf32Adm: 32SF4 RL UL Count: 5sf4AdmUl: 20DL Code Allocation Level: 40.23 %dlCodeAdm: 80 %beMarginDlCode: 5UL Interference: -105.2 dBmFiltered DL Power: 23.44 %pwrAdm: 75 %pwrAdmOffset: 10 %beMarginDlPwr: 10Congestion State: Uncongested$

To change cell reserved unreserved,

1) moshell to RNC

2) lt all

3) lget alammu cellreserved

To change to unreserved

4)lset alammu_1 cellreserved 1

To change to reserved

5) lset alammu_1 cellreserved 0