3D Printing & Additive Manufacturing - PC (Polycarbonate) · 2020. 5. 12. · 511-10501 T10 tip 511-10301 T12 tip 511-10401 T16 tip 511-10701 T20 tip 511-10100 T12SR100 tip, 0.005,

PC

Dat

a S

heet

PC (Polycarbonate)

FDM Thermoplastic Filament

The information presented are typical values intended for reference and comparison purposes only. They should not be used for design specifications or quality control purposes.

http://www.stratasys.com/?utm_source=logos&utm_medium=pdf&utm_content=footer-stratasys-logo

PC

Dat

a S

heet

2

OverviewPC is a polycarbonate FDM® filament that brings the attributes of this industrial plastic to 3D printing applications. PC is

characterized by its high strength and impact resistance, coupled with dimensional stability and heat resistance. These attributes

make it a good choice for 3D printed prototypes, parts and tools that demand higher material properties than ABS or ASA.

FDM PC is available in white and is compatible with both breakaway and soluble support materials.

Contents:Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Physical Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mechanical Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8


PC

Dat

a S

heet

3

Build Sheet

Low Temperature

• 0.02 x 26 x 38 in.

• 0.02 x 16 x 18.5 in.

• 0.02 x 14 x 16.5 in

Ordering Information

Table 1. Printer and Support Material Compatibility

Printer Model Tip (Slice) Support Material Support Tip

Fortus 360mc™

T10 (5 slice)

T12 (7, 10 slice)

T16 (10 slice)

T20 (13 slice)

SR-110™ (soluble) (5, 7, 10 slice)

PC-BASS (breakaway) (7, 10, 13 slice)

T12SR100 (SR-110) (5, 7, 10 slice)

T12 (PC-BASS) (7 slice)

T16 (PC-BASS) (10, 13 slice)

Fortus 400mc™

T10 (5 slice)

T12 (7, 10 slice)

T16 (10 slice)

T20 (13 slice)

SR-110 (soluble) (5, 7, 10 slice)


T12SR100 (SR-110) (5, 7, 10 slice)



Fortus 380mc™/450mc™

T10 (5 slice)

T12 (7, 10 slice)

T16 (10 slice)

T20 (13 slice)



T12SR100 (SR-110) (5, 7, 10 slice)



Fortus 900mc™/F900™

T12 (7, 10 slice)

T16 (10 slice)

T20 (13 slice)



T12SR100 (SR-110) (7, 10, 13 slice)



BASS = breakaway support system.


PC

Dat

a S

heet

4

Part Number Description

Filament Canisters1 2

355-02210 PC, 92.3 cu in. - Plus

355-08210 PC, 184 cu in. - Plus

360-50210 PC, Xtend 500 - Plus

310-20100 PC, 92.3 cu in. - Classic

310-20118 PC, 184 cu in. - Classic

355-03210 PC BASS, 92.3 cu in. - Plus

360-53210 PC BASS, Xtend 500 - Plus

310-30100 PC BASS, 92.3 cu in. - Classic

355-03120 SR-100 Soluble Support, 92.3 - Plus

310-31100 SR-100 Soluble Support, 92.3 - Classic

Printer Consumables

511-10501 T10 tip

511-10301 T12 tip

511-10401 T16 tip

511-10701 T20 tip

511-10100 T12SR100 tip, 0.005, 0.007, and 0.010 in. support layer heights

325-00300 Low Temperature build sheet, 0.2 x 26 x 38 in. (0.76 x 660 x 965 mm)

325-00100 Low Temperature build sheet, 0.2 x 16 x 18.5 in. (0.76 x 406 x 470 mm)

355-00100 Low Temperature build sheet, 0.2 x 16 x 16.5 in. (0.76 x 406 x 420 mm)

1 Classic canisters are compatible with all Fortus 400mc and Fortus 900mc printers prior to s/n L502 .

2 Plus canisters are compatible with all Fortus 450mc, all Stratasys F900, and Fortus 900mc printers s/n L502 and up .

Table 2. PC Ordering Information


PC

Dat

a S

heet

5

Values are measured as printed. XY, XZ, and ZX orientations were tested. For full details refer to the Stratasys

Materials Test Report (immediate download upon clicking the link). DSC and TMA curves can be found in the

Appendix.

Table 3. PC Physical Properties

Physical Properties

PropertyProperty Test MethodTest MethodTypical ValuesTypical Values

XYXY XZ/ZXXZ/ZX

HDT @ 66 psiASTM D648

Method B145 °C (293 °F)

HDT @ 264 psiASTM D648

Method B140 °C (284 °F)

TgASTM D7426

Inflection Point140 °C (284 °F)

Mean CTE

ASTM E831

(-50 °C to 120 °C) - 50 µm/[m*°C] (28 µin./[in.*°F])

ASTM E831

(-50 vC to 30 °C)50 µm/[m*°C] (28 µin./[in.*°F]) -

ASTM E831

(30 °C to 75 °C)35 µm/[m*°C] (19 µin./[in.*°F]) -

ASTM E831

(75 °C to 130 °C)10 µm/[m*°C] (5.5 µin./[in.*°F]) -

Volume Resistivity ASTM D257 > 6.8*10^14 Ω*cm

Dielectric Constant

ASTM D150

1 kHz test condition2.66 2.84

ASTM D150

2 MHz test condition2.53 2.69

Dissipation Factor

ASTM D150

1 kHz test condition-0.002

ASTM D150

2 MHz test condition0.003 0.008

Specific GravityASTM D257

@23 °C1.20

http://www.stratasys.com/?utm_source=logos&utm_medium=pdf&utm_content=footer-stratasys-logohttps://www.stratasys.com/-/media/Files/Brochures/BR_FDM_MaterialsTestingProcedure_0919ahttps://www.stratasys.com/-/media/Files/Brochures/BR_FDM_MaterialsTestingProcedure_0919a

PC

Dat

a S

heet

6

Print Orientation

Parts created using FDM are anisotropic as a result of

the printing process. Below is a reference of the different

orientations used to characterize the material.

PC samples were printed with 0.010 in. (0.254 mm) layer heights on the F900. For the full test procedure please see the

Stratasys Materials Test Procedure (immediate download upon clicking the link).

Mechanical Properties

Tensile Curves

Due to the anisotropic nature of FDM, tensile curves look

different depending on orientation. Below is a guide of the two

types of curves seen when printing tensile samples and what

reported values mean.

Z

Y

X

Flat (XY) On Edge (XZ) Upright (ZX)

A = Tensile at break, elongation at break (no yield point)

STRAIN

ST

RE

SS

YIELD POINT

B = Tensile at yield, elongation at yield

C = Tensile at break, elongation at break

A

BC

http://www.stratasys.com/?utm_source=logos&utm_medium=pdf&utm_content=footer-stratasys-logohttps://www.stratasys.com/-/media/Files/Brochures/BR_FDM_MaterialsTestingProcedure_0919a

PC

Dat

a S

heet

7

Table 4. PC Mechanical Properties (Fortus 900mc - T16 Tip)

XZ Orientation1 ZX Orientation1

Tensile Properties: ASTM D638

Yield StrengthMPa 60 (2) No yield

psi 8390 (235) No yield

Elongation @ Yield % 4.9 (0.1) No yield

Strength @ BreakMPa 57 (2) 35 (10)

psi 8310 (235) 5145 (1310)

Elongation @ Break % 5.2 (0.4) 1.8 (0.2)

Modulus (Elastic)GPa 2.25 (0.05) 2.1 (0.1)

ksi 325 (7) 310 (15)

Flexural Properties: ASTM D790, Procedure A

Strength @ BreakMPa No break 75 (5)

psi No break 10870 (780)

Strength @ 5% StrainMPa 90 (2) -

psi 13050 (240) -

Strain @ Break % No break 4.5 (0.4)

ModulusGPa 2.15 (0.04) 1.88 (0.07)

ksi 310 (6) 270 (10)

Compression Properties: ASTM D695

Yield StrengthMPa 245 (10) 290 (20)

psi 35410 (1930) 42055 (2795)

ModulusGPa 1.95 (0.05) 2.11 (0.09)

ksi 280 (10) 305 (15)

Impact Properties: ASTM D256, ASTM D4812

NotchedJ/m 75 (10) 25 (7)

ft*lb/in. 1.4 (0.2) 0.5 (0.1)

UnnotchedJ/m 760 (105) 230 (70)

ft*lb/in. 15 (2) 4 (1)

1 Values in parentheses are standard deviations.


PC

Dat

a S

heet

8

Figure 1. 2nd heating scan DSC data for the PC Flat (XY) sample.

DSC

Appendix


PC

Dat

a S

heet

9

Figure 2. Dimension change data as a function of temperature for the PC Flat (XY) sample.

Figure 3. Dimension change data as a function of temperature for the PC On Edge (XZ) sample.

TMA

TMA


PC

Dat

a S

heet

10

1 Holtzman St., Science Park, PO Box 2496 Rehovot 76124, Israel +972 74 745 4000+972 74 745 5000 (Fax)

© 2020 Stratasys. All rights reserved. Stratasys, the Stratasys Signet logo, FDM, and Fortus are registered trademarks of Stratasys Inc. Fortus 360mc, Fortus 380mc, Fortus 400mc, Fortus 450mc, Fortus 900mc, F900 and SR-110 are trademarks of Stratasys, Inc. All other trademarks are the property of their respective owners, and Stratasys assumes no responsibility with regard to the selection, performance, or use of these non-Stratasys products. Product specifications subject to change without notice.Printed in the USA. MDS_FDM_PC_0420a

Stratasys Headquarters 7665 Commerce Way, Eden Prairie, MN 55344+1 800 801 6491 (US Toll Free)+1 952 937-3000 (Intl)+1 952 937-0070 (Fax)

stratasys.com ISO 9001:2015 Certified

Figure 4. Overlay of the dimension change data for the Flat (XY) and On Edge (XZ) PC samples.

TMA
http://www.stratasys.com/?utm_source=logos&utm_medium=pdf&utm_content=footer-domain-linkhttp://www.stratasys.com/?utm_source=logos&utm_medium=pdf&utm_content=s-logo

Documents

3D Printing & Additive Manufacturing - PC (Polycarbonate) · 2020. 5. 12. · 511-10501 T10 tip 511-10301 T12 tip 511-10401 T16 tip 511-10701 T20 tip 511-10100 T12SR100 tip, 0.005,