3.2 S-MS, S-MD Z en -Autoperforantes

11 / 2009 3.11

Product information

Applications Screws with sealing washers for fastening profile steel sheet to profile steel sheet or forfastening profile steel sheet to steel framing.

Screws without sealing washers for framing fastenings (not exposed to weather).

Product descriptionThe screw first drills the required hole in the part to be fastened and in theframing (A). Then the thread is cut (B).A watertight seal is formed at the fastening when the screw with sealing washer is driven. The carbon steel screw is case hardened. The surface of the screw is galvanized. This protects the screw from corrosion and lubrica-tes the drilling and thread-cutting operation.

Several screw programs have been awarded approval by the building inspectionauthorities in Germany.Please note the approval mark shown for each of the applicable screw programs.All screws can be ordered with coloured heads and washers in colours according to the RALcolour chart.

Screw designationse.g.: S-MD 51 Z 5.5x45 S for screw fastening

M for metal constructionD for self-drilling screw (D = drilling)5 2 pressed-on steel flange 15 mm

4 sealing washer 14 mm5 sealing washer 16 mm6 sealing washer 19 mm7 sealing washer 22 mm0 without sealing washer

1 1 drill point # 1 = 1.25 up to approx. 3 mm drillingthickness3 drill point # 3 = 2.1 to 6 mm drilling thickness5 drill point # 5 = 4.6 to 12 mm drilling thicknessPlease refer to the screw program for the specific max.drilling thickness for each screw.

Z galvanized carbon steel (Z for zinc)5.5x45screw dimensions ( x length)

Further designations:S-MD51Z 4.8x19 PB15 PB 15 screw head in the colours listed in the RAL colour chartS-MD51LZ 4.8x38 L extended drill pointS-MD01Z 4.8x19M M collatedS-MD01Y 4.8x19 Y surface galvanized and yellow chromated

Z-14.1-4Hilti

MPANRW

Carbon steel self-drilling screws

S-MD51Z

3.12 11 / 2009

S-MD51Z 4.8L carbon steel self-drillingscrew for sheet overlaps

General informationMaterial specification:galvanized, case-hardened, with reduced-diameter drill point and fitted EPDM sealingwasher, 16 mm.Self-drilling screws with coloured head andsealing washer; other special colours avail-able on request.

Product data

Approvals Z-14.1-4Hilti

MPANRW

H

SW L

DC MF

d

mm

DC / MF

Sheet metal joints

DimensionsUses:Fastening sheet metal to sheet metal

Fastening toolsScrewdriver: Hilti ST2500,

Hilti ST1800Drive using depthgauge set: Item no. 304611Nut set driverS-NSD8: Item no. 308901

ApplicationsExamples

11 / 2009 3.13

S-MD51Z

Design data

Load data

Drilling capacity tmax. 2.75 mm

Tightening torque (recommendation)

Screw in end-stop oriented

Total thickness tl: up to 1.25 mm up to 2.75 mmTightening torque: 2 Nm 5 Nm

Component II steel with tll [mm] S235J according to DIN EN 10025-2S280GD or S320GD (DIN EN 10326)

0.63 0.75 0.88 1.00 1.13 1.25 1.50 2.00

Component Isteel with tl [mm] S280GD or S320GD(DIN EN 10326) Shear force VR,k [kN]

0.63 1.30 1.80 2.30 2.90 2.90 2.90ac 2.90ac 2.90ac

0.75 1.30 1.80 2.30 2.90 3.51 3.70ac 3.70ac 3.70a

0.88 1.30 1.80 2.30 2.90 3.51 4.10 4.80*

1.00 1.30 1.80 2.30 2.90 3.51 4.10 5.60

1.13 1.30 1.80 2.30 2.90 3.51 4.10 5.60

1.25 1.30 1.80 2.30 2.90 3.51 4.10 5.60

1.50 1.30 1.90 2.70 3.60 4.70 5.90

Tension force NR,k [kN]

0.50 0.43 0,54 0.70 0.81 0.97ac 1.13ac 1.40ac 1.40ac

0.55 0.55 0.68 0.89 1.02 1.23ac 1.43ac 1.77ac 1.77ac

0.63 0.80 1.00 1.30 1.50 1.80ac 2.10ac 2.60ac 2.60ac

0.75 0.80 1.00 1.30 1.50 1.80 2.10ac 2.70ac 2.70a

0.88 0.80 1.00 1.30 1.50 1.80 2.10 2.70*

1.00 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.13 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.25 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.50 0.80 1.00 1.30 1.50 1.80 2.10 2.70

S-MD51Z

3.14 11 / 2009

Screw selection

Screw programDrilling Fastening Dimensions Sealing Head RAL colour Package Ordering Item no.thickness thickness washer size contents designationDC MF (dxL) AFmm max. mm mm mm

1.22.75 5.5 4.8x19 16 8 500 S-MD51Z 4.8x19 219032

RAL colours available immediately from stock

1.22.75 5.5 4.8x19 16 8 1015 light ivory 500 S-MD51Z 4.8x19 PB15 224616

1.22.75 5.5 4.8x19 16 8 5008 grey blue 500 S-MD51Z 4.8x19 PF08 231397

1.22.75 5.5 4.8x19 16 8 7022 umbra grey 500 S-MD51Z 4.8x19 PH22 224617

1.22.75 5.5 4.8x19 16 8 8012 red brown 500 S-MD51Z 4.8x19 PK12 235208

1.22.75 5.5 4.8x19 16 8 9002 grey white 500 S-MD51Z 4.8x19 PL02 224615

1.22.75 5.5 4.8x19 16 8 9006 white aluminium 500 S-MD51Z 4.8x19 PL06 224614

1.22.75 5.5 4.8x19 16 8 9010 pure white 500 S-MD51Z 4.8x19 PL10 224613

(a)single

(b)side lap

(c)end overlap

(d)side lap and end overlap

Safety factors according to EN 1993-1-3 and CUAP 06.02/07

Tension Shear

Partial safety concept

Partial safety factor M = 1.33 M = 1.33Influence of cyclic loading cyclic = 1.0 /

Design load NRd = 1.0 NRk / 1.33 VRd = VRk / 1.33

Global safety concept

Global safety factor * GLOB = 2.0 GLOB = 2.0Recommended load NRd = 1.0 NRk / 2.0 VRd = VRk / 2.0* Note: The global safety factor of 2.0 includes a partial safety factor of F = 1.5 for wind load. For other loads safetyfactors should be applied in accordance with the appropriate standards.

11 / 2009 3.15

S-MD51Z

S-MD51Z 6.3L carbon steel self-drillingscrew

General informationMaterial specification:galvanized, case-hardened, with reduced-diameter drill point and fitted EPDM sealingwasher 16 mm. Coloured screws available on request.

Product data

Approvals: Z-14.1-4Hilti

MPANRW

H

SW L DC MF

d

mm

DCmax / MFmax

DCmin

DimensionsUses:Fastening sheet steel to thin steel sections and liner trays.

Fastening tools:Screwdriver: Hilti ST2500,

Hilti ST1800Drive using depth gauge set: Item no. 304611Nut set driver S-NSD3/8": Item no. 308905


S-MD51Z

3.16 11 / 2009

Design data

Load data




Total thickness tl: up to 1,25 mm up to 3,00 mmTightening torque: 4 Nm 8 Nm

Component II steel with tll [mm] S280GD or S320GD (DIN EN 10326)

0.63 0.75 0.88 1.00 1.13 1.25 1.50 2.00


0.63 1.60 2.10 2.70 3.30 3.30ac 3.30ac 3.30ac 3.30ac

0.75 1.60 2.10 2.70 3.30 4.10 4.20ac 4.20ac 4.20*

0.88 1.70 2.20 2.80 3.40 4.10 4.40 5.20ac 5.20*

1.00 1.80 2.40 3.00 3.50 4.10 4.60 5.80 6.30*

1.13 1.80 2.40 3.00 3.50 4.20 4.80 6.20

1.25 1.80 2.40 3.00 3.60 4.20 5.00 6.50

1.50 2.00 2.60 3.30 4.00 4.80 5.50 7.20

1.75 2.00 2.60 3.30 4.00

2.00 2.00 2.60 3.30 4.00


0.50 0.49 0.65 0.81 0.97 1.13ac 1.30ac 1.67ac 1.73ac

0.55 0.61 0.82 1.02 1.23 1.43ac 1.64ac 2.11ac 2.18ac

0.63 0.90 1.20 1.50 1.80 2.10ac 2.40ac 3.10ac 3.20ac

0.75 0.90 1.20 1.50 1.80 2.10 2.40ac 3.10ac 4.00*

0.88 0.90 1.20 1.50 1.80 2.10 2.40 3.10ac 4.60*

1.00 0.90 1.20 1.50 1.80 2.10 2.40 3.10 4.60*

1.13 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.25 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.50 0.90 1.20 1.50 1.80 2.10 2.40 3.10

11 / 2009 3.17

S-MD51Z

Screw selection

Screw programDrilling Fastening Dimensions Sealing Head Package Ordering Item no.thickness thickness washer size contents designationDC MF (dxL) AFmm max. mm mm mm

1.2-3 4 6.3x19 16 3/8" 500 S-MD51Z 6.3x19 219034


Tension Shear






(a)single

(b)side lap

(c)end overlap


1.75 0.90 1.20 1.50 1.80

2.00 0.90 1.20 1.50 1.80

S-MD51LZ

3.18 11 / 2009

S-MD51LZ 4.8L carbon steel self-drillingscrew

General informationMaterial specification:galvanized, case-hardened, with fittedEPDM sealing washer 16 mm and extend-ed drill point.Self-drilling screws with coloured head andsealing washer; other special colours avail-able on request.

Product data

H

L

DC

d

MF SW

mm

DCmin

DCmaxMFmax

Sheet metal joints

DimensionsUses on siding:Fastening trapezoidal profile metal sheets with intermediate insulating layer to steel sections.


Hilti ST1800Drive using depth gauge set: Item no. 304611Nut set driver S-NSD8: Item no. 308901


11 / 2009 3.19

S-MD51LZ

Design data

Load data

Drilling capacity tmax. 2,75 mm




Component II steel with tll [mm] S280GD or S320GD (DIN EN 10326))

0.63 0.75 0.88 1.00 1.13 1.25 1.50


0.63 1.40 1.40 1.90 2.40 2.70 3.00 3.00

0.75 1.40 1.70 1.90 2.40 2.70 3.30 3.30

0.88 1.40 1.70 1.90 2.40 2.70 3.30 3.30

1.00 1.40 1.70 1.90 2.40 2.70 3.30 3.30

1.13 1.40 1.70 1.90 2.40 2.70 3.30 3.30

1.25 1.40 1.70 1.90 2.40 2.70 3.30 3.30

1.50 1.40 1.70 1.90 2.40 2.70 3.30


0.63 0.60 0.90 1.10 1.30 1.60 1.80 2.50

0.75 0.60 0.90 1.10 1.30 1.60 1.80 2.50

0.88 0.60 0.90 1.10 1.30 1.60 1.80 2.50

1.00 0.60 0.90 1.10 1.30 1.60 1.80 2.50

1.13 0.60 0.90 1.10 1.30 1.60 1.80 2.50

1.25 0.60 0.90 1.10 1.30 1.60 1.80 2.50

1.50 0.60 0.90 1.10 1.30 1.60 1.80

S-MD51LZ

3.20 11 / 2009

Screw selection


1.2-2.75 13 4.8x38 16 8 250 S-MD51LZ 4.8x38 252801


1.2-2.75 13 4.8x38 16 8 1002 sand yellow 250 S-MD51LZ 4.8x38 PB02 309220

1.2-2.75 13 4.8x38 16 8 1015 light ivory 250 S-MD51LZ 4.8x38 PB15 258793

1.2-2.75 13 4.8x38 16 8 1019 grey beige 250 S-MD51LZ 4.8x38 PB19 309227

1.2-2.75 13 4.8x38 16 8 3000 flame red 250 S-MD51LZ 4.8x38 PB00 309225

1.2-2.75 13 4.8x38 16 8 5008 grey blue 250 S-MD51LZ 4.8x38 PB08 374757

1.2-2.75 13 4.8x38 16 8 7006 beige grey 250 S-MD51LZ 4.8x38 PB06 309226

1.2-2.75 13 4.8x38 16 8 7008 khaki grey 250 S-MD51LZ 4.8x38 PB08 258795

1.2-2.75 13 4.8x38 16 8 7022 amber 250 S-MD51LZ 4.8x38 PB22 258794

1.2-2.75 13 4.8x38 16 8 7032 pebble grey 250 S-MD51LZ 4.8x38 PB32 309224

1.2-2.75 13 4.8x38 16 8 8012 red brown 250 S-MD51LZ 4.8x38 PB12 374756

1.2-2.75 13 4.8x38 16 8 9002 grey white 250 S-MD51LZ 4.8x38 PB02 258792

1.2-2.75 13 4.8x38 16 8 9006 white aluminium 250 S-MD51LZ 4.8x38 PB06 258791

1.2-2.75 13 4.8x38 16 8 9010 pure white 250 S-MD51LZ 4.8x38 PB10 258790


Tension Shear






(a)single

(b)side lap

(c)end overlap


11 / 2009 3.21

S-MD53Z


General informationMaterial specification:galvanized, case-hardened, 4.8 mm, withfitted EPDM sealing washer, 16 mm.Self-drilling screws with coloured head andsealing washer; other special colours avail-able on request.

Product data


MPANRW

L

DC

dH

MF SW mm

DCmax / MFmax

DCmin DCmin

DCmaxMFmax

without insulation with insulation

DimensionsUses:Fastening sheet metal to steel framing, with or without intermediate insulation layers.




S-MD53Z

3.22 11 / 2009

Design data

Load data






1.50 2.00 2.50 3.00


0.63 2.40ac 2.70ac 2.70ac 2.70ac

0.75 3.00 3.50ac 3.50ac 3.90ac

0.88 3.40 4.10 4.10 5.40

1.00 3.70 4.70 4.70 6.60

1.13 4.00 5.00 5.00 6.70

1.25 4.40 5.30 5.30 6.80

1.50 4.90 5.60 5.60 6.90

1.75 490 5.60 5.60

2.00 4.90 5.60 5.60


0.50 0.92ac 1.40ac 1.40ac 1.40ac

0.55 1.16ac 1.77ac 1.77ac 1.77ac

0.63 1.70ac 2.60ac 2.60ac 2.60ac

0.75 1.70 2.70ac 2.70ac 3.30ac

0.88 1.70 2.70 2.70 4.20

1.00 1.70 2.70 2.70 5.00

1.13 1.70 2.70 2.70 5.20

1.25 1.70 2.70 2.70 5.20

11 / 2009 3.23

S-MD53Z

Screw selection


2.1-4.5 5 4.8x19 16 8 500 S-MD53Z 4.8x19 219035

2.1-4.5 18 4.8x38 16 8 500 S-MD53Z 4.8x38 224612


2.1-4.5 18 4.8x32 16 8 7032 pebble grey 500 S-MD53Z 4.8x38 PH32 235224


Tension Shear






(a)single

(b)side lap

(c)end overlap


1.50 1.70 2.70 2.70 5.20

1.75 1.70 2.70 2.70

2.00 1.70 2.70 2.70

S-MD53Z

3.24 11 / 2009

S-MD53Z 5.5L galvanized carbon steelscrew

General informationMaterial specification:self-drilling, case-hardened, with fittedEPDM sealing washer, 16 mm.Self-drilling screws with coloured head andsealing washer; other special colours avail-able on request.

Product data


MPANRW

L

DC

dH

MF SW mm

DCmax / MFmax

DCmin DCmin

DCmaxMFmax






11 / 2009 3.25

S-MD53Z

Design data

Load data






2.00 2.50 3.00 4.00


0.63 3.10 ac 3.10 ac 3.10 ac 3.10 abcd

0.75 3.80 ac 3.80 ac 3.80 ac 3.80 ac

0.88 4.60 4.60 4.60 ac 4.60 a

1.00 5.30 5.30 5.40 5.49 a

1.13 5.30 5.30 6.20 6.20

1.25 5.30 5.30 7.60 9.80

1.50 6.10 6.10 9.10 12.00

1.75 6.10 6.10 9.10

2.00 7.80 7.80 9.70


0.50 1.62 ac 1.62 ac 1.73 ac 1.73 abcd

0.55 2.05 ac 2.05 ac 2.18 ac 2.18 abcd

0.63 3.00 ac 3.00 ac 3.20 ac 3.20abcd

0.75 3.00 ac 3.00 ac 3.90 ac 3.90 ac

0.88 3.00 3.00 4.80 ac 4.80 a

1.00 3.00 3.00 5.30 5.60 a

1.13 3.00 3.00 5.30 6.50

1.25 3.00 3.00 5.30 7.20

S-MD53Z

3.26 11 / 2009

Screw selection


2.6-5.5 4 5.5x19 16 8 500 S-MD53Z 5.5x19 219036

2.6-5.5 10 5.5x25 16 8 500 S-MD53Z 5.5x25 219037

2.6-5.5 17 5.5x32 16 8 500 S-MD53Z 5.5x32 219038

2.6-5.5 23 5.5x38 16 8 250 S-MD53Z 5.5x38 219039

2.6-5.5 35 5.5x50 16 8 250 S-MD53Z 5.5x50 235105


2.6-5.5 10 5.5x25 16 8 1015 light ivory 500 S-MD53Z 5.5x25 PB15 224639

2.6-5.5 10 5.5x25 16 8 9010 pure white 500 S-MD53Z 5.5x25 PL10 224636

2.6-5.5 10 5.5x25 16 8 7022 amber 500 S-MD53Z 5.5x25 PH22 224640

2.6-5.5 10 5.5x25 16 8 5008 grey blue 500 S-MD53Z 5.5x25 PF08 231398

2.6-5.5 10 5.5x25 16 8 9002 grey white 500 S-MD53Z 5.5x25 PL02 224638

2.6-5.5 10 5.5x25 16 8 9006 white aluminium 500 S-MD53Z 5.5x25 PL06 224637

2.6-5.5 10 5.5x25 16 8 8012 red brown 500 S-MD53Z 5.5x25 PK12 235228


Tension Shear






(a)single

(b)side lap

(c)end overlap


1.50 3.00 3.00 5.30 7.20

1.75 3.00 3.00 5.30

2.00 3.00 3.00 5.30

11 / 2009 3.27

S-MD53Z


General informationMaterial specification:galvanized, case-hardened, with fittedEPDM sealing washer, 16 mm.Coloured screws available on request.

Product data


MPANRW

L

DC

dH

MF SW mm

DCmax / MFmax

DCmin DCmin

DCmaxMFmax




Hilti ST1800Drive using depth gauge set: Item no. 304611Nut set driver S-NSD 3/8: Item no. 308905


S-MD53Z

3.28 11 / 2009

Design data

Load data






2.00 2.50 3.00 4.00


0.63 3.00 ac 3.00 ac 3.00 abcd 3.00 abcd

0.75 3.80 ac 3.80 ac 3.80 abcd 3.80 abcd

0.88 4.60 4.80 4.80 ac 4.80 abc

1.00 5.10 5.10 5.70 ac 5.70 ac

1.13 5.50 5.50 6.80 ac 6.80 a

1.25 6.10 6.10 7.90 ac 7.90 a

1.50 6.40 6.40 0.00 10.30 a

1.75 6.40 6.40 9.00 10.30

2.00 7.80 7.80 9.40 10.80


0.50 1.67 ac 1.67 ac 1.78 abcd 1.78 abcd

0.55 2.11 ac 2.11 ac 2.25 abcd 2.25 abcd

0.63 3.10 ac 3.10 ac 3.30 abcd 3.30 abcd

0.75 3.10 ac 3.10 ac 4.00 abcd 4.00 abcd

0.88 3.10 3.10 4.80 ac 4.80 abc

1.00 3.10 3.10 5.60 ac 5.60 ac

1.13 3.10 3.10 5.60 ac 6.40 a

1.25 3.10 3.10 5.60 ac 7.20 a

11 / 2009 3.29

S-MD53Z

Screw selection

Screw programDrilling Fastening Dimensions Sealing Head Package Ordering Item no.thickness thickness washer size contents designationDC MF (dxL) AFmm max. mm mm mm

2.6-6 4 6.3x19 163/8" 500 S-MD53Z 6.3x19 219040

2.6-6 10 6.3x25 163/8" 500 S-MD53Z 6.3x25 219041

2.6-6 17 6.3x32 163/8" 500 S-MD53Z 6.3x32 219042

2.6-6 23 6.3x38 163/8" 250 S-MD53Z 6.3x38 219043

2.6-6 35 6.3x50 163/8" 250 S-MD53Z 6.3x50 219044


Tension Shear






(a)single

(b)side lap

(c)end overlap


1.50 3.10 3.10 5.60 7.20 a

1.75 3.10 3.10 5.60 7.20

2.00 3.10 3.10 5.60 7.20

S-MD55Z / S-MD65Z

3.30 11 / 2009

S-MD55Z 5.5L/S-MD65Z 5.5L carbonsteel self-drilling screw

General informationMaterial specification:galvanized, case-hardened, with fittedEPDM sealing washer 16, 19 mm.Self-drilling screws with coloured head andsealing washer; other special colours availa-ble on request.

Product data

Approvals: Z-14.1-4Hilti

MPANRW

L

DC

dH

mm

MFSW

DCmax / MFmax

DCmin DCmin

DCmaxMFmax



Fastening tools:Screwdriver: Hilti ST1800Drive using depth gauge set: Item no. 304611Nut set driver S-NSD8: Item no. 308901


11 / 2009 3.31

S-MD55Z / S-MD65Z

Design data

Load data




Tightening torque: 5 Nm


4.00 5.00 6.00 > 6.00


0.63 3.30 abcd 3.30 abcd 3.30 abcd 3.30 abcd

0.75 3.90 ac 3.90 ac 3.90 abcd 3.90 abcd

0.88 4.40 ac 4.40 ac 4.40 abcd 4.40 abcd

1.00 4.90 ac 4.90 ac 4.90 ac 4.90 ac

1.13 5.40 5.40 ac 5.40 ac 5.40 ac

1.25 7.30 7.30 ac 7.30 ac 7.30 ac

1.50 7.90 7.90 7.90 7.90

1.75 7.90 7.90 7.90 7.90

2.00 9.10 9.10 9.10 9.10





0.75 3.20 ac 3.20 ac 3.20 abcd 3.20 abcd

0.88 3.40 ac 3.40 ac 3.40 abcd 3.40 abcd

1.00 3.60 ac 3.60 ac 3.60 ac 3.60 ac

1.13 3.80 3.80 ac 3.80 ac 3.80 ac

1.25 4.00 4.00 ac 4.00 ac 4.00 ac

1.50 4.30 4.30 4.30 4.30

S-MD55Z / S-MD65Z

3.32 11 / 2009

Screw selection


4.6-12 15 5.5x38 16 8 250 S-MD55Z 5.5x38 227504

4.6-12 27 5.5x50 16 8 250 S-MD55Z 5.5x50 219046

4.6-12 40 5.5x63 16 8 100 S-MD55Z 5.5x63 219048

4.6-12 15 5.5x38 19 8 250 S-MD65Z 5.5x38 227508


4.6-12 15 5.5x38 16 8 1015 light ivory 250 S-MD55Z 5.5x38 PB15 224376

4.6-12 15 5.5x38 16 8 9010 pure white 250 S-MD55Z 5.5x38 PL10 224373

4.6-12 15 5.5x38 16 8 7022 amber 250 S-MD55Z 5.5x38 PH22 224377

4.6-12 15 5.5x38 16 8 5008 grey blue 250 S-MD55Z 5.5x38 PF08 374758

4.6-12 15 5.5x38 16 8 9002 grey white 250 S-MD55Z 5.5x38 PL02 224375

4.6-12 15 5.5x38 16 8 9006 white aluminium 250 S-MD55Z 5.5x38 PL06 224374

4.6-12 15 5.5x38 16 8 8012 red brown 250 S-MD55Z 5.5x38 PK12 374759


Tension Shear






(a)single

(b)side lap

(c)end overlap


1.75 4.30 4.30 4.30 4.30

2.00 4.90 4.90 4.90 4.90

11 / 2009 3.33

S-MS01Z

S-MS01Z carbon steel self-drilling screwfor sheet overlaps

General informationMaterial specification:galvanized, case-hardened.

Fastening tools:Screwdriver: Hilti ST1800Drive without depth gauge. Cut-out controlled by torque clutchNut set driver S-NSD8: Item no. 308901

Product data

SW

t It II

DimensionsUses:Side lap connector

Stand-up tool with screwdriver Hilti SDT30,

ST1800Drive without depth gauge. Cut-out controlled by torque clutchBit holder S-BH 435DT: Item no. 304415S-NSD8 DT nut set driver: Item no. 304413

Approvals:Z-14.1-4Hilti

MPANRW


Examples of applications for the S-MS01Z:

19

4.8

S-MS01Z

3.34 11 / 2009

Design data

Load data

Drilling capacity tmax. 2.5 mm (max. 21.25 mm)




Component II steel with tll [mm] S280GD, S320GD or S350GD (DIN EN 10326)

0.50 0.55 0.63 0.75 0.88 1.00 1.13 1.25

Component Isteel with tl [mm] S280GD, S320GD orS350GD (DIN EN 10326) Shear force VR,k [kN]

0.50 1.29 1.37 1.51 1.71 1.71 1.71 1.71 1.71

0.55 1.29 1.54 1.65 1.82 1.82 1.82 1.82 2.05

0.63 1.29 1.54 1.80 2.00 2.00 2.00 2.00 2.59

0.75 1.29 1.54 1.80 2.27 2.27 2.27 2.84 3.40

0.88 1.29 1.54 1.80 2.27 2.96 2.96 2.96 3.40

1.00 1.29 1.54 1.80 2.27 2.96 3.64 3.64 3.64

1.13 1.29 1.54 1.80 2.27 2.96 3.64 3.87 3.87

1.25 1.29 1.54 1.80 2.27 2.96 3.64 3.87 4.10


0.50 0.76 0.87 1.04 1.29 1.56 1.82 1.93 1.93

0.55 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.25

0.63 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.34

0.75 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.34

0.88 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.34

1.00 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.34

1.13 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.34

1.25 0.76 0.87 1.04 1.29 1.56 1.82 2.09 2.34

11 / 2009 3.35

S-MS01Z


Tension Shear






Screw selection

Screw programDrilling thickness Fastening thickness Dimensions Head size Package Ordering Item no.DC MF (dxL) AF contents designationmm max. mm mm

2.5 2.5 4.8x20 8 250 S-MS01Z 4.8x20 385448

Collated self-drilling screws can be driven using the SDT30 stand-uptool and ST1800 metal construction screwdriver.


2.5 2.5 4.8x20 8 250 S-MS01Z 4.8x20 M 385450

S-MD01Z / S-MD01Y

3.36 11 / 2009

S-MD01Z, S-MD01Y carbon steel self-drilling screw

General informationMaterial specification:S-MD01Z: galvanized, case-hardened.S-MD01Y: galvanized and yellow chromat-ed, case-hardened.

Fastening toolsScrewdriver: Hilti ST1800Torque settings 4.2 = 1 3

4.8 = 3 5 5.5 = 6 8 6.3 = 810

Drive without depth gauge. Cut-out controlled by torque clutchNut set driver:S-MD01Z 4.2L S-NSD7

Item no. 308900S-MD01Z 4.8x19 S-NSD8

Item no. 308901S-MD01Z 6.3x19 S-NSD3/8"

Item no. 308905

Product data

H

L

MF DC

d

SW

DC / MF

Sheet metal joints

DimensionsUses:Overlap joints in load-bearing (decking)sheets not exposed to the weather. Fastening liner trays, web joints.


ST1800Torque settings: 4.8 = 35

5.5 = 68Drive without depth gauge. Cut-out controlled by torque clutchBit holder S-BH 435DT: Item no. 304415S-NS D8 nut set driver: Item no. 304413


MPANRW

DCmax / MFmax

DCmin DCmin

DCmaxMFmax


11 / 2009 3.37


S-MD01Z / S-MD01Y

3.38 11 / 2009

S-MD01Z 4.2

Design data

Load data






0,63 0,75 0,88 1,00 1,13 1,25 1,50


0.63 1.50 2.00 2.50 2.60 2.60 ac 2.60 ac 2.60 a

0.75 1.70 2.10 2.60 3.00 3.60 4.00 4.00

0.88 1.80 2.20 2.80 3.30 4.00 4.50 4.50

1.00 1.90 2.40 3.00 3.60 4.30 5.00 5.00

1.13 1.90 2.40 3.00 3.60 4.30 5.00

1.25 1.90 2.40 3.00 3.60 4.30 5.00

1.50 1.90 2.40 3.00 3.60


0.63 0.90 1.20 1.40 1.40 1.40 ac 1.40 ac 1.40 a

0.75 0.90 1.20 1.40 1.70 1.90 2.00 2.00

0.88 0.90 1.20 1.40 1.70 1.90 2.20 2.70

1.00 0.90 1.20 1.40 1.70 1.90 2.20 2.80

1.13 0.90 1.20 1.40 1.70 1.90 2.20

1.25 0.90 1.20 1.40 1.70 1.90 2.20

1.50 0.90 1.20 1.40 1.70

11 / 2009 3.39

S-MD01Z 4.2

Screw selection


1.2-2.50 4.5 4.2x13 7 1000 S-MD01Z 4.2x13 224500

1.2-2.50 7.5 4.2x16 7 1000 S-MD01Z 4.2x16 010405


Tension Shear






(a)single

(b)side lap

(c)end overlap


3.40 11 / 2009

S-MD01Z 4.8

Design data

Load data






0,63 0,75 0,88 1,00 1,13 1,25 1,50 2,00


0.63 1.40 1.80 2.10 2.40 2.70 3.00 ac 3.60 ac 3.60 ac

0.75 1.40 1.90 2.30 2.70 3.10 3.50 4.40 4.40 a

0.88 1.40 1.90 2.40 2.90 3.30 3.90 5.10

1.00 1.40 1.90 2.40 3.00 3.60 4.30 5.80

1.13 1.30 1.90 2.40 3.00 3.60 4.30 5.80

1.25 1.40 1.90 2.40 3.00 3.60 4.30 5.80

1.50 1.40 2.00 2.70 3.50 4.40 5.40


0.63 0.80 1.00 1.30 1.40 1.40 1.40 ac 1.40 ac 1.40 ac

0.75 0.80 1.00 1.30 1.50 1.80 2.00 2.00 2.00 a

0.88 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.00 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.13 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.25 0.80 1.00 1.30 1.50 1.80 2.10 2.70

1.50 0.80 1.00 1.30 1.50 1.80 2.10

11 / 2009 3.41

S-MD01 4.8

Screw selection

Screw program for sheet overlaps (with reduced drill point diameter)Drilling thickness Fastening thickness Dimensions Head size Package Ordering Item no.DC MF (dxL) AF contents designationmm max. mm mm

1.2-2.75 8.5 4.8x19 8 500 S-MD01Z 4.8x19 219557

Screw program Mechanical and Electrical Drilling thickness Fastening thickness Dimensions Head size Package Ordering Item no.DC MF (dxL) AF contents designationmm max. mm mm

1,2-2,75 3,5 4,8x13 8 1000 S-MD01Z 4.8x13 224501

1,2-2,75 6,5 4,8x16 8 500 S-MD01Y 4.8x16 257732

Collated self-drilling screws can be driven using the SDT25 stand-uptool and ST1800 metal construction screwdriver.

Screw program for sheet overlaps (with reduced drill point diameter)Drilling thickness Fastening thickness Dimensions Head size Package Ordering Item no.DC MF (dxL) AF contents designationmm max. mm mm

1.2-2.75 8.5 4.8x19 8 250 S-MD01Z 4.8x19M 378978

1.2-2.75 7 4.8x22 8 250 S-MD01LZ 4.8x22M 284488


Tension Shear






(a)single

(b)side lap

(c)end overlap


3.42 11 / 2009

S-MD01Z 5.5

Design data

Load data






0,63 0,75 0,88 1,00 1,13 1,25 1,50 2,00


0.63 1.50 1.80 2.00 2.10 2.30 2.40 2.60 ac 2.60 ac

0.75 1.60 2.00 2.50 2.90 3.40 3.80 3.80 ac 3.80 a

0.88 1.70 2.10 2.60 3.00 3.50 4.00 4.50 5.10

1.00 1.90 2.30 2.80 3.20 3.70 4.20 5.20 5.20

1.13 2.70 3.10 3.60 3.90 4.40 5.10 5.90

1.25 3.50 3.90 4.30 4.60 5.00 6.00 6.60

1.50 3.50 3.90 4.30 4.60 5.60 6.00 6.60

1.75 3.50 3.90 4.30 4.60

2.00 3.50 3.90 4.30 4.60


0.63 0.90 1.20 1.50 1.70 1.70 1.70 1.70 ac 1.70 ac

0.75 0.90 1.20 1.50 1.80 2.10 2.30 2.30 ac 2.30 a

0.88 0.90 1.20 1.50 1.80 2.10 2.40 2.90 2.90

1.00 0.90 1.20 1.50 1.80 2.10 2.40 3.10 3.50

1.13 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.25 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.50 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.75 0.90 1.20 1.50 1.80

2.00 0.90 1.20 1.50 1.80

11 / 2009 3.43

S-MD01Z 5.5

Screw selection


1.2-3 7.5 5.5x19 8 500 S-MD01Z 5.5x19 219558


Tension Shear






(a)single

(b)side lap

(c)end overlap


3.44 11 / 2009

S-MD01Z 6.3

Design data

Load data






0,63 0,75 0,88 1,00 1,13 1,25 1,50 2,00


0.63 1.50 2.00 2.50 2.90 3.50 3.70 ac 3.70 ac 3.70 ac

0.75 1.90 2.30 2.80 3.30 3.80 4.30 4.80 ac 4.80 ac

0.88 2.00 2.40 2.90 3.30 3.80 4.30 5.10 6.00 a

1.00 2.10 2.50 3.00 3.40 3.90 4.40 5.40 7.20

1.13 2.10 2.50 3.10 3.60 4.20 4.80 6.00

1.25 2.10 2.60 3.30 3.90 4.60 5.20 6.70

1.50 2.10 2.60 3.30 3.90 4.60 5.20 6.70

1.75 2.10 2.60 3.30 3.90

2.00 2.10 2.60 3.30 3.90


0.63 0.90 1.20 1.50 1.80 1.90 1.90 ac 1.90 ac 1.90 ac

0.75 0.90 1.20 1.50 1.80 2.10 2.40 2.40 ac 2.40 ac

0.88 0.90 1.20 1.50 1.80 2.10 2.40 3.10 3.40 a

1.00 0.90 1.20 1.50 1.80 2.10 2.40 3.10 4.30

1.13 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.25 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.50 0.90 1.20 1.50 1.80 2.10 2.40 3.10

1.75 0.90 1.20 1.50 1.80

2.00 0.90 1.20 1.50 1.80

11 / 2009 3.45

S-MD01Z 6.3

Screw selection


1.2-3 7 6.3x19 3/8" 500 S-MD01Z 6.3x19 219559


Tension Shear






(a)single

(b)side lap

(c)end overlap


3.46 11 / 2009

S-MD03Z / S-MD23Z / S-MD2310Y

S-MD03Z, S-MD23Z, S-MD2310Y carbonsteel self-drilling screw for sheet overlaps

General informationMaterial specification:S-MD03Z: galvanized, case-hardened.S-MD23Z: galvanized, case-hardened, withpressed-on flange.S-MD2310Y: galvanized and yellow chro-mated, case-hardened, with pressed-onflange.

Fastening tools:Screwdriver: Hilti ST1800Torque settings: 4.2 = 1 3

4.8 = 3 5 5.5 = 6 8 6.3 = 810

Drive without depth gauge. Cut-out controlled by torque clutchNut set driver:S-MD03Z 4.2x16 + S-NSD7S-MD03Z 4.8xL Item no. 308900S-MD03Z 5.5x25 + S-NSD8S-MD23Z 5.5x22 + Item no. 308901S-MD2310Y 6.3x22M

Product data

H

L

MF DC

d

SW

DC / MF

Sheet metal joints

DimensionsUses:Overlap joints in load-bearing (decking)sheets not exposed to the weather.Fastening liner trays, web joints.


ST1800Torque settings: 4.8 = 35

5.5 = 68Drive without depth gauge. Cut-out controlled by torque clutchBit holder S-BH 435DT: Item no. 304415Nut set driver:S-MD03Z S-NS D8

Item no. 304413S-MD23Z + S-NSD10 DTS-MD2310Y 6.3x22M Item no. 284485


MPANRW

DCmax / MFmax

DCmin DCmin

DCmaxMFmax


11 / 2009 3.47

S-MD03Z 4.2


3.48 11 / 2009

S-MD03Z 4.2

Design data

Load data






1.25 1.50 2.00


0.63 2.20 2.40 2.40

0.75 2.40 2.70 3.20

0.88 2.60 2.90 3.30

1.00 2.70 3.20 3.70

1.13 2.70 3.20 3.70

1.25 2.70 3.20 3.70


0.63 1.00 1.60 2.00

0.75 1.00 1.60 2.30

0.88 1.00 1.60 2.60

1.00 1.00 1.60 2.60

1.13 1.00 1.60 2.60

1.25 1.00 1.60 2.60

11 / 2009 3.49

S-MD03Z 4.2

Screw selection


2.1-3.50 7 4.2x16 7 1000 S-MD03Z 4.2x16 219013


Tension Shear






3.50 11 / 2009

S-MD03Z 4.8

Design data

Load data






1.50 2.00 2.50 3-00


0.63 2.30 2.70 ac 2.70 ac 2.70 ac

0.75 2.30 3.00 3.00 3.80 ac

0.88 2.60 3.50 3.50 4.90

1.00 2.90 4.00 4.00 6.00

1.13 3.50 4.60 4.60 6.60

1.25 4.10 5.20 5.20 7.10

1.50 5.20 6.00 6.00 7.30

1.75 5.20 6.00 6.00

2.00 5,20 6.00 6.00


0.63 1.60 1.60 1.60 ac 1.60 ac

0.75 1.60 2.20 2.20 2.20 ac

0.88 1.60 2.40 2.40 3.00

1.00 1.60 2.40 2.40 3.90

1.13 1.60 2.40 2.40 4.10

1.25 1.60 2.40 2.40 4.10

1.50 1.60 2.40 2.40 4.10

1.75 1.60 2.40 2.40

2.00 1.60 2.40 2.40

11 / 2009 3.51

Screw selection


2.1-4.50 7 4.8x16 8 500 S-MD03Z 4.8x16 219015

2.1-4.50 10 4.8x19 8 500 S-MD03Z 4.8x19 219016

(a)single

(b)side lap

(c)end overlap


S-MD03Z 4.8


Tension Shear






3.52 11 / 2009

S-MD03Z 5.5/S-MD23Z 5.5

Design data

Load data







2.00 2.50 3.00 4.00


0.63 2.60 ac 2.60 ac 2.60 ac 2.60 ac

0.75 3.70 ac 3.70 ac 3.70 ac 3.70 ac

0.88 4.50 4.50 5.00 ac 5.00 ac

1.00 4.50 4.50 6.50 ac 6.50 ac

1.13 4.90 4.90 7.00 7.90 a

1.25 5.30 5.30 7.40 9.30

1.50 6.20 6.20 8.30 10.10

1.75 6.20 6.20 8.30

2.00 7.80 7.80 9.40

11 / 2009 3.53

Screw selection


2.6-5.50 6 5.5x19 8 500 S-MD03Z 5.5x19 219018

2.6-5.50 12 5.5x25 8 500 S-MD03Z 5.5x25 *) 219019

2.6-5.50 19 5.5x32 8 500 S-MD03Z 5.5x32 219020

2.6-5.50 25 5.5x38 8 500 S-MD03Z 5.5x38 219021

2.6-5.5 10 5.5x22 8 500 S-MD23Z 5.5x22 234590

*) Screw for sheet overlaps with reduced drill point diameter

(a)single

(b)side lap

(c)end overlap



0.63 1.70 ac 1.70 ac 1.70 ac 1.70 ac

0.75 2.20 ac 2.20 ac 2.20 ac 2.20 ac

0.88 2.80 2.80 2.90 ac 2.90 ac

1.00 2.80 2.80 3.50 ac 3.50 a

1.13 2.80 2.80 4.30 4.30

1.25 2.80 2.80 4.90 5.10

1.50 2.80 2.80 4.90 6.90

1.75 2.80 2.80 4.90

2.00 2.80 2.80 4.90

S-MD03Z 5.5/S-MD23Z 5.5


Tension Shear






S-MD03Z 6.3 / S-MD23Z 6.3 /S-MD2310Y 6.3

3.54 11 / 2009

Design data

Load data






2.00 2.50 3.00 4.00


0.63 3.10 ac 3.10 ac 3.10 abcd 3.10 abcd

0.75 4.20 ac 4.20 ac 4.20 abcd 4.20 abcd

0.88 5.40 ac 5.40 ac 5.40 ac 5.40 abcd

1.00 5.60 5.60 6.60 ac 6.60 ac

1.13 5.70 5.70 7.80 8.00 ac

1.25 5.90 5.90 9.00 9.50 ac

1.50 7.00 7.00 9.70 12.30

1.75 7.00 7.00 9.70 12.30

2.00 7.00 7.00 9.70 12.30


0.63 1.90 ac 1.90 ac 1.90 abcd 1.90 abcd

0.75 2.60 ac 2.60 ac 2.60 abcd 2.60 abcd

0.88 3.10 ac 3.10 ac 3.40 ac 3.40 abcd

1.00 3.10 3.10 4.30 ac 4.30 ac

1.13 3.10 3.10 5.30 5.30 ac

1.25 3.10 3.10 5.60 6.40 ac

1.50 3.10 3.10 5.60 6.90

1.75 3.10 3.10 5.60 6.90

2.00 3.10 3.10 5.60 7.20

11 / 2009 3.55

S-MD03Z 6.3 / S-MD23Z 6.3 /S-MD2310Y 6.3

Screw selection


2.6-6.00 6 6.3x19 3/8" 500 S-MD03Z 6.3x19 219022

2.6-6.00 12 6.3x25 3/8" 500 S-MD03Z 6.3x25 219023

2.6-6.00 19 6.3x32 3/8" 500 S-MD03Z 6.3x32 219024

2.6-6.00 37 6.3x50 3/8" 250 S-MD03Z 6.3x50 219026

2.6-6.00 9 6.3x22 10 200 S-MD2310Y 6.3x22M 284487

2.6-6.00 6 6.3x19 10 500 S-MD23Z 6.3x19 025541

2.6-6.00 9 6.3x22 10 500 S-MD2310Y 6.3x22 257731

2.6-6.00 12 6.3x25 10 500 S-MD23Z 6.3x25 025543

2.6-6.00 42 6.3x55 10 250 S-MD23Z 6.3x55 374755

(a)single

(b)side lap

(c)end overlap



Tension Shear






S-MD21Z

3.56 11 / 2009

S-MD21Z carbon steel self-drilling screws

General informationMaterial specification:galvanized, case-hardened, with pressed-onflange.

Fastening toolsScrewdriver: Hilti ST1800Torque settings: 68Drive without depth gauge. Cut-out controlled by torque clutch.Nut set driver: S-NSD8

Item no. 308901S-NSD10Item no. 308902

Product data

H

15

SW L

DC MF

d

DCmax / MFmax

DCmin

DimensionsUses:Fastening supporting decking sheets to steel framing. Screw with pressed-on flange, particularly suitable for highly-stressed fastenings, e.g. roofing sheets on insulated (built-up) roofs.


ST1800Torque settings: 6.3 = 810Drive without depth gauge. Cut-out controlled by torque clutch.Bit holder: S-BH 435DT

Item no. 304415Nut set driver: S-NSD10 DT

Item no. 284485

11 / 2009 3.57

S-MD21Z


Design data

Load data





Component II steel with tll [mm] S280GD or S320GD (DIN EN 10326)

1.50 2.00


0.63 2.20 2.20

0.75 2.20 3.80

0.88 2.20 4.20

1.00 2.20 4.20

1.13 2.20 4.20

1.25 2.20 4.20

S-MD21Z

3.58 11 / 2009

Screw selection


1.2-3 15 5.5x25 8 500 S-MD21Z 5.5x25 234588


0.63 1.50 1.50

0.75 1.50 2.20

0.88 1.50 2.80

1.00 1.50 3.60

1.13 1.50 3.60

1.25 1.50 3.60


Tension Shear






11 / 2009 3.59

S-MD05Z / S-MD25Z

S-MD05Z, S-MD25Z carbon steel self-drilling screws

General information -MD05ZMaterial specification:galvanized, case-hardened.

Fastening toolsScrewdriver: Hilti ST1800Torque settings: 810Drive without depth gauge. Cut-out controlled by torque clutch.Nut set driver: S-NSD8

Item no. 308901


MPANRW

Product data

Material specification:galvanized, case-hardened, with pressed-onflange.

Fastening toolsScrewdriver: Hilti ST1800Torque settings: 46Drive without depth gauge. Cut-out controlled by torque clutch.Nut set driver: S-NSD

Item no. 308901S-NSD10Item no. 308902

Stand-up tool with screwdriver: Hilti SDT25,

ST1800Torque settings: 6.3 = 810Drive without depth gauge. Cut-out controlled by torque clutch.Bit holder: S-BH 435DT

Item no. 304415Nut set driver: S-NSD10 DT

Item no. 284485

General information S-MD25Z

S-MD05Z / S-MD25Z

3.60 11 / 2009

Dimensions S-MD05ZUses:Fastening steel sections and sheet steel tosteel framing, with or without insulatingmaterial.

H

L

MF DC

d

SW

DCmax / MFmax

DCmin DCmin

DCmaxMFmax

without insulation with insulationH

15

SW L

DC MF

d

DCmax / MFmax

DCmin

Dimensions S-MD25ZUses:Fastening supporting decking sheets tosteel framing. Screw with pressed-on flange,particularly suitable for highly-stressedfastenings, e.g. roofing sheets on insulated(built-up) roofs.

ApplicationsExamples: S-MD05Z

11 / 2009 3.61

S-MD05Z / S-MD25Z

ApplicationsExamples: S-MD25Z

Design data

Load data




Tightening torque: 5 Nm


4.00 5.00 6.00 > 6.00



0.75 3.40 abcd 3.40 abcd 3.40 abcd 3.4 abcd0

0.88 4.20 ac 4.20 ac 4.20 ac 4.20 ac

1.00 4.90 ac 4.90 ac 4.90 ac 4.90 ac

1.13 5.70 ac 5.70 ac 5.70 ac 5.70 ac

1.25 6.50 6.50 6.50 6.50

1.50 7.60 7.60 7.60 7.60

1.75 7.60 7.60 7.60 7.60

2.00 7.60 7.60 7.60 7.60

S-MD05Z / S-MD25Z

3.62 11 / 2009

Screw selection


4.6-12.00 18 5.5x38 8 250 S-MD05Z 5.5x38 219030

4.6-12.00 30 5.5x50 8 250 S-MD05Z 5.5x50 219028

4.6-12.00 43 5.5x63 8 250 S-MD05Z 5.5x63 219031

4.6-12.00 18 5.5x38 8 500 S-MD25Z 5.5x38 234598

(a)single

(b)side lap

(c)end overlap





0.88 2.10 ac 2.10 ac 2.10 ac 2.10 ac

1.00 2.40 ac 2.40 ac 2.40 ac 2.40 ac

1.13 2.70 ac 2.70 ac 2.70 ac 2.70 ac

1.25 3.00 3.00 3.00 3.00

1.50 3.60 3.60 3.60 3.60

1.75 3.60 3.60 3.60 3.60

2.00 4.80 4.80 4.80 4.80


Tension Shear






Documents

3.2 S-MS, S-MD Z en -Autoperforantes