Upload
others
View
11
Download
0
Embed Size (px)
Citation preview
IOWA MOLD TOOLING CO., INC.
P.O. Box 189Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
32 / 222 Technical
Specifications
Manual # 99905811
Revised 01-28-2019
Copyright © 2019 Iowa Mold Tooling Co., Inc.All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company
ii
32 / 222 - Manual # 99905811
Operating, servicing and maintaining this vehicle or equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle or equipment in a well-ventilated area and wear gloves or wash your hands frequently when servicing. For more information go to www.P65Warnings.ca.gov. 70490167
70490167PROP 65BKS 5-29-18
ORANGE , BLACK AND WHITE3.27” 2.70”
CN
iii
32 / 222 - Manual # 99905811
Table of Contents
Section - 1 1
32 / 222 - Specifications .................................................................................................................................232 / 222 - Specifications - Continued .............................................................................................................332 / 222 - Specifications - Continued .............................................................................................................432 / 222 - Metric Specifications ......................................................................................................................532 / 222 - Metric Specifications - Continued ..................................................................................................632 / 222 - Metric Specifications - Continued ..................................................................................................7
Section - 2 9
32 / 222 K2 - Capacity Chart .......................................................................................................................1032 / 222 K3 - Capacity Chart ........................................................................................................................ 1132 / 222 K4 - Capacity Chart ........................................................................................................................1232 / 222 K5 - Capacity Chart ........................................................................................................................1332 / 222 K6 - Capacity Chart ........................................................................................................................1432 / 222 K7 - Capacity Chart ........................................................................................................................1532 / 222 K8 - Capacity Chart ........................................................................................................................1632 / 222 K2-K8 - Lifting Capacity Chart .......................................................................................................1732 / 222 - Lifting Capacity with Winch ..........................................................................................................18
Section - 3 19
32 / 222 - Dimension Sketch, Winch 2.5T ....................................................................................................2032 / 222 - Dimension Sketch, TS-RC ...........................................................................................................2132 / 222 - Technical Data, Winch .................................................................................................................2232 / 222 - Technical Data, Winch (Metric) ....................................................................................................22
Section - 4 23
32 / 222 - Specifications with Fly-Jib ............................................................................................................2432 / 222 - Specifications with Fly-Jib (Metric) ..............................................................................................25
Section - 5 27
32 / 222 K4 FJ1000 K4 - Capacity Chart .....................................................................................................2832 / 222 K4 FJ1000 K5 - Capacity Chart .....................................................................................................2932 / 222 K5 FJ1000 K3 - Capacity Chart .....................................................................................................3032 /222 K5 FJ1000 K2 - Capacity Chart ......................................................................................................3132 / 222 K5 FJ1000 K4 - Capacity Chart .....................................................................................................3232 / 222 K5 FJ1000 K5 - Capacity Chart .....................................................................................................3332 / 222 Lifting Capacity, Fly Jib with Winch ................................................................................................34
Section - 6 36
32 / 222 - Dimension Sketch, K5 with FJ1000 .............................................................................................37
Section - 7 40
32 / 222 - Hydraulic Diagram, Danfoss Single-Circuit Crane Functions ......................................................4132 / 222 - Hydraulic Diagram, Danfoss, Single-Circuit FJ with EXV + Winch ..............................................4232 / 222 - Hydraulic Diagram, Danfoss Single-Circuit Variable & Fixed ......................................................4332 / 222 - Hydraulic Diagram, Stabilizer Circuit + 4 FCTS. ..........................................................................4432 / 222 - Pressure Setting Diagram ............................................................................................................4532 / 222 - Pressure Setting Diagram, Fly-Jib ...............................................................................................4632 / 222 - Pressure Setting Diagram (Metric) ..............................................................................................4732 / 222 - Pressure Setting Diagram, Fly-Jib (Metric) ..................................................................................48
iv
32 / 222 - Manual # 99905811
This page left intentionally blank
v
32 / 222 - Manual # 99905811
This page left intentionally blank
vi
32 / 222 - Manual # 99905811
Section - 1 1 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
Section - 130 / 222 Technical Specifications
Section - 1 2 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
32 / 222 - Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3/HD5 H1/B3/HD5 H1/B3/HD5 H1/B3/HD5 H1/B3/HD5 H1/B3/HD5 H1/B3/HD5
Load moment ft-lb 221599 215102 212937 207162 201388 200666 195613Hydraulic reach ft 27’ 2” 33’ 8” 40’ 7” 47’ 9” 55’ 1” 62’ 3” 69’ 9”Hydraulic telescopic movement
ft 12’ 1” 18’ 8” 25’ 6” 32’ 6” 39’ 9” 47’ 3” 54’7”
Lifting capacity, hydraulic
lb-ft 15060-14’8”
10690-20’7”
8200-26’9”
14620-14’8”
10275-20’7”
7760-26’9”
6220-33’5”
14130-15’1”
9830-21’0”
7340-27’2”
5775-33’8”
4785-40’4”
13735-15’1”
9460-21’0”
6990-27’2”
5425-33’8”
4410-40’7”
3750-47’6”
13380-15’1”
9130-21’0”
6635-27’2”
5095-33’8”
4080-40’7”
3420-47’6”
2930-54’8”
13030-15’4”
8820-21’3”
6330-27’6”
4785-33’8”
3770-40’7”
3085-47’6”
2625-54’8”
2295-62’0”
12720-15’4”
8510-21’3”
6065-27’6”
4495-34’1”
3485-41’0”
2800-47’9”
2335-54’4”
2005-62’0”
1765-69’6”Lifting capacity, manual extensions
lb-ft 2425-62’0” 1984-69’6” 1499-76’8”
992-84’6”
Slewing torque, gross lb-ft 28078
Slewing angle °Max. heel at max. load moment
° 5
Slewing speed °/s 10
Minimum Chassis SpecsFront Axle Rating (GAWR) 20,000 lbs (9,072 kg)Rear Axle Rating (GAWR) 40,000 lbs (18,150 kg)Resistance to Bending Moment 3,330,000 in-lbs (38,365 kg-m)
Section - 1 3 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
32 / 222 - Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis ft-in 7’ 7”Width ft-in 8’ 2”Length, no extra valves ft-in 3’ 4” 3’ 7”Length, with extra valves (hose guides) ft-in 4’ 3” - -
Length, with 2 extra valve (hose reels + winch) ft-in - - 4’ 2”
Length, with extra valves (int. hose routing + winch) ft-in 4’ 2” - -
Stabilizer spread, min., 2xS=1625 ft-in 18’2”
Stabilizer spread max., 2xS=2065 ft-in 21’ 1”
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers lb 5710 6151 6592 6967 7319 7650 7926
Stabilizers beam, 1xS=1625 lb 298Stabilizers beam,1xS=2065 lb 397Stabilizer cylinders, 1x swing-up lb 88
Stabilizers cylinders, 1xhyd. swing-up lb -
Mounting kit - long, 8 bolts lb 154Mounting kit - 4 bolts lb 88Manual extensions
lb150 128 104
88
Oil in loader (stowing position) lb 77 88 97 104 112 123 132
Tank 160L, excl. oil (fitted on loader)* lb 165
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 4 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
32 / 222 - Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K81 extra valve, int. hose routing lb 165 176 187 -2 extra valves, hose guides lb 165 198 231 265 298 -2 extra valves, hose reels lb - 408 4082 extra valves, int. hose routing lb 287 309 320 331 -Winch (2.5 t), single snatch block lb 397 408 419
Winch (2.5 t), double snatch block lb 441 452 463Extra proportional RC-function on the base lb 26
Oil cooler lb 66
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S=1650 (swing-up / hydr. Swing-up ft-lb 287S=2065 (swing-up / hydr. swing-up ft-lb 280
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure PSI 5294
Max. pump performance, fixed flowgpm 21KW 49
Max. pump performance, variablegpm 34KW 80
Max. oil consumption gal 10 12 14 15 16 17 18
Section - 1 5 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
32 / 222 - Metric Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999)
H1/B3/HD5
H1/B3/HD5
H1/B3/HD5
H1/B3/HD5
H1/B3/HD5
H1/B3/HD5
H1/B3/HD5
Load moment tm 30.7 29.8 29.5 28.7 27.9 27.8 27.1Hydraulic reach m 8.3 10.3 12.4 14.6 16.8 19 21.3Hydraulic telescopic movement mm 3680 5730 7810 9950 12150 14410 16670
Lifting capacity. hydraulic kg-m
6830-4.5
4850-6.3
3720-8.2
6630-4.5
4660-6.3
3520-8.2
2820-10.2
6410-4.6
4460-6.4
3330-8.3
2620-10.
2170-12.3
6230-4.6
4460-6.4
3330-8.3
2620-10.3
2170-12.3
6070-4.6
4140-6.4
3010-8.3
2310-10.3
1850-12.4
1550-14.5
1330-16.7
5910-4.7
4000-6.5
2870-8.4
2170-10.3
1710-12.4
1400-14.5
1190-16.7
1040-18.9
5770-4.7
3860-6.5
2750-8.4
2040-10.4
1580-12.5
1270-14.6
1060-16.7
910-18.9
800-21.2
Lifting capacity. manual extensions kg-m
1100-18.9 900-12.2 680-23.4
450-25.8Slewing torque. gross kNm 38
Slewing angle ° -
Max. heel at max. load moment ° 5
Slewing speed °/s 10
Section - 1 6 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
32 / 222 - Metric Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis mm 2350Width mm 2500Length, no extra valves mm 1024 1130Length, with extra valves (hose guides) mm 1147 -
Length, with 2 extra valve (hose reels + winch) mm - 1286 1239
Length, with extra valves (int. hose routing + winch) mm 1024 -
Stabilizer spread min., 2xS=1625 mm 5550
Stabilizer spread max., 2xS=2065 mm 6430
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers kg 3610 3900 4170 4420 4620 4800 4975
Stabilizers beam, 1xS=1625 kg 135Stabilizers beam,1xS=2065 kg 180Stabilizer cylinders, 1x swing-up kg 50
Stabilizers cylinders, 1xhyd. swing-up kg
Mounting kit - long, 8 bolts kg 70Mounting kit -4 bolts kg 40Mounting kit - subframe kgManual extensions kg
kg - - - -68 58 60
75
Oil in loader (stowing position) kg 77 88 97 104 112 123 132
Tank 160L, excl. oil (fitted on loader)* kg 165
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 7 30 / 222 Technical Specifications
32 / 222 - Manual # 99905811
32 / 222 - Metric Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K81 extra valve, int hose routing kg 75 80 85 -2 extra valves, hose guides kg 75 90 105 120 135 -1 extra valve, hose reels kg - 1851 extra valve, int. hose routing kg 130 140 145 150 -Winch (2.5 t), single snatch block kg 180 185 190
Winch (2.5 t), double snatch block kg 200 205 210
Winch (3.2 t), single snatch block kg 240
Winch (3.2 t), double snatch block kg 275 280 285Extra proportional RC-funcfion on the base kg 12
Oil cooler kg 30
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S=1650 (swing-up / hydr. Swing-up kN 130S=2065 (swing-up / hydr. swing-up kN 127
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure Bar 365
Max. pump performance, fixed flowL/min 80KW 49
Max. pump performance, variableL/min 130KW 80
Max. oil consumption L 39 40 52 56 60 64 68
This page left intentionally blank
8
32 / 222 - Manual # 99905811
Section - 2 9 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
Section - 232 / 222 Capacity Charts
Section - 2 10 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K2 - Capacity Chart
70399606
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K2
03'
6'9'
12'15'
18'21'
24'27'
30'33'
0MOUNTINGSURFACE
3'(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
36'(10.97m)
39'(11.89m)
150606830
KGLB
CENTERLINE (1.83m) (3.66m) (5.49m) (7.32m) (9.14m)
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
106904850
82003720
Section - 2 11 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K3 - Capacity Chart
70399607
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K3
0CENTERLINE 3'
6'9'
12'15'
18'21'
24'27'
30'33'
0MOUNTINGSURFACE
3'(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
36'(10.97m)
39'(11.89m)
42'(12.80m)
(0.91m)
(1.83m)
(2.74m)
(3.66m)
(4.57m)
(5.49m)
(6.40m)
(7.32m)
(8.23m)
(9.14m)
(10.06m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
102754660
146206630
77603520
62202820
KGLB
Section - 2 12 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K4 - Capacity Chart
70399608
6' 12' 18' 24' 30' 36' 42'0CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K4
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m) (12.80m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
73403330
57752620
47852170
98304460
141306410
KGLB
Section - 2 13 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K5 - Capacity Chart
70399609
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K5
6' 12' 18' 24' 30' 36' 42'0CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
37501700
44102000
54252460
69903170
94604290
KGLB
137356230
(1.83m) (3.66m) (5.49m) (7.32m) (10.97m)(9.14m) (12.80m)
3' 9' 15' 21' 27' 33' 39'(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m) (11.89m)
45'(13.72m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 14 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K6 - Capacity Chart
70399610
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K6
6' 12' 18' 24' 30' 36' 42' 48' 54'0CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66353010 5095
2310 40801850
34201550 2930
1330
KGLB
133806070
91304140
(1.83m) (3.66m) (5.49m) (7.32m) (10.97m)(9.14m) (12.80m) (14.63m)(16.46m)
3' 9' 15' 21' 27' 33' 39'(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m) (11.89m)
45'(13.72m)
51'(15.55m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 15 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K7 - Capacity Chart
70399611
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K7
6'12'
18'24'
30'36'
42'48'
54'60'0
CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
47852170 3770
1710 30851400 2625
119022951040
KGLB
63302870
88204000
(1.83m)
(3.66m)
(5.49m)
(7.32m) (10.97m)
(9.14m) (12.80m)
(14.63m)
(16.46m)
(18.29m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
130305910
Section - 2 16 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K8 - Capacity Chart
70399612
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model32 / 222 K8
6'12'
18'24'
30'36'
42'48'
54'60'
66'0
CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
72'(21.95m)
KGLB
(1.83m)
(3.66m)
(5.49m)
(7.32m) (10.97m)
(9.14m) (12.80m)
(14.63m)
(16.46m)
(18.29m)
(20.12m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
9102005
8001765
15803485
10602335
12702800
20404495
577012720
38608510
27506065
Section - 2 17 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 K2-K8 - Lifting Capacity Chart
3220-K2
3220-K3
3220-K4
3220-K5
3220-K6
3220-K7
3220-K8
149976’8”
FT 20’7”10690
14’8”15060
26’9”8200
33’5”6220
14’8”14620
20’7”
LB
M 6,34850
4,56830
8,23720KG
10275FT 26’9”
7760
27’2”
LB
10,22820
4,56630
6,34660
M 8,23520KG
7340FT 21’0”
983015’1”
1413033’8”5775
40’4”4785
40’7”4410
33’8”5425
15’1”13735
21’0”
LB
8,33330
M 6,44460
4,66410
10,32620
12,32170KG
9460FT 27’2”
699047’6”3750
14,51700
40’7”4080
33’8”5095
15’1”13380
21’0”
LB
12,42000
10,32460
4,66230
6,44290
M 8,33170KG
9130FT 27’2”
663547’6”3420
54’8”2930
40’7”3770
33’8”4785
15’4”13030
21’3”
LB
12,41850
10,32310
4,66070
6,44140
M 8,33010KG
8820FT 27’6”
633047’6”3085
54’8”2625
62’0”2295
41’0”3485
34’1”4495
15’4”12720
21’3”
LG
12,41710
10,32170
4,75910
6,54000
M 8,42870KG
8510FT 27’6”
606547’9”2800
54’8”2335
62’0”2005
69’6”1765
62’0”2425
14,51550
16,71330
18,91100
69’6”1984
14,51400
16,71190
18,91040
21,2900
LG
12,51580
10,42040
4,75770
6,53860
M 8,42750KG
99284’6”
68023,414,6
127016,71060
18,9910
21,2800 450
25,8
LIFTING WITHOUT MANUAL EXTENSIONS
LIFTING WITH MANUAL EXTENSIONS
Section - 2 18 32 / 222 Capacity Charts
32 / 222 - Manual # 99905811
32 / 222 - Lifting Capacity with Winch
Hydraulic hoist type
90°
0°
65°
Not recommended workning angle.
MAXW MAXWD1500 kg 3000 kg2500 kg 5000 kg
Dinamic S 25 Brevini 2500
Dinamic P9E Dinamic P15E
3200 kg 6400 kg
MAXW MAXWD3307 lb 6614 lb5512 lb 11023 lb
7055 lb 14110 lb
Section - 3 19 30 / 222 Dimension Drawings
32 / 222 - Manual # 99905811
Section - 330 / 222 Dimension Drawings
Section - 3 20 30 / 222 Dimension Drawings
32 / 222 - Manual # 99905811
32 / 222 - Dimension Sketch, Winch 2.5T
16.4
” 4
17
175
0
TOP CHASSIS
5’ 7
”
Section - 3 21 30 / 222 Dimension Drawings
32 / 222 - Manual # 99905811
32 / 222 - Dimension Sketch, TS-RC
690 2’ 3”
2’ 5” 775
19.3
” 4
90
5’ 8
” 1
755
23.6” 600
8’ 4
” 2
555
4’ 5
”
147
5
R10
60R
1110
* Cannot be selected for cranes with hydraulic tank on the base.
Section - 3 22 30 / 222 Dimension Drawings
32 / 222 - Manual # 99905811
32 / 222 - Technical Data, WinchPERFORMANCE (2438 PSI): UNIT 2.5T WINCHMax. wire pull – 1st layer lb 5512Max. wire pull – 2nd layer lb 5071Max. wire pull – 3rd layer lb 4630Max. wire pull – 4th layer lb 4300WIRE SPEED (15.9 GPM): UNITS 2.5T WINCHMax. wire speed – 1st layer ft/min 79Max. wire speed – 2nd layer ft/min 85Max. wire speed – 3rd layer ft/min 92Max. wire speed – 4th layer ft/min 98WEIGHTS: UNITS 2.5T WINCHTare weight, winch (CE) lb 198Fixed parts (valve section, brackets,hoses etc.) lb 110
Wire Ø10 x197 ft lb 66Spare parts, single snatch block lb 44Spare parts, double snatch block lb 88
32 / 222 - Technical Data, Winch (Metric)
PERFORMANCE (2438 PSI): UNIT 2.5T WINCHMax. wire pull – 1st layer kg 2500Max. wire pull – 2nd layer kg 2300Max. wire pull – 3rd layer kg 2100Max. wire pull – 4th layer kg 1950WIRE SPEED (15.9 GPM): UNITS 2.5T WINCHMax. wire speed – 1st layer m/min 24Max. wire speed – 2nd layer m/min 26Max. wire speed – 3rd layer m/min 28Max. wire speed – 4th layer m/min 30WEIGHTS: UNITS 2.5T WINCHTare weight, winch (CE) kg 90Fixed parts (valve section, brackets,hoses etc.) kg 50
Wire Ø10 x 60 m kg 30Spare parts, single snatch block kg 20Spare parts, double snatch block kg 40
Section - 4 23 32 / 222 Technical Specifications Fly-Jibs
32 / 222 - Manual # 99905811
Section - 432 / 222 Technical Specifications Fly-Jibs
Section - 4 24 32 / 222 Technical Specifications Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 - Specifications with Fly-Jib32 / 222-K4 + FJ1000 32 / 222-K5 + FJ1000
Performance Unit FJ K3 FJ K4 FJ K5 FJ K3 FJ K4 FJK5Hydraulic reach ft-lb 66’ 9” 72’ 8” 79’ 4” 73’8” 79’ 7” 86’ 3”Hydraulic telescopic movement, Fly-jib ft. 16’ 4” 22’ 1” 28’6” 16’ 4” 22’ 1” 28’ 6”
Out-reach with manual extensions ft. - 79’ 4” - - 86’ 3” -
Lifting capacity, hydraulic ft-lb.
2447-50’5”2161-55’4”1940-60’7”1742-66’9”
2348-50’5”2072-55’4”1841-60’7”1653-66’9”1510-72’8”
2194-50’5”1918-55’8”1698-61’0”1510-66’9”1367-73’2”1246-79’4”
1764-51’1”1565-62’3”1411-67’6”1268-73’5
1653-57’1”1455-62’3”1301-67’6”1168-73’5”1058-79’4”
1510-57’4”1323-62’7”1168-67’9”1036-73’8”926-79’7”761-86’0
Lifting capacity, manual exten-sions ft-lb. - 1246-79’4”
1069-85’6” - - 805-86’0”628-92’5” -
Dimensions:Height above chassis-with winch ft-in 8’ 8”
Height above chassis- excl. winch ft-in 8’ 8”
Width ft-in 8’ 2”Length, without extra valve kit on fly-jib ft-in 3’ 8”
Length, with extra valve kit on fly-jib ft-in 3’ 8”
Weights:Fly-jib 1) lb 1499 1676 1830 1477 1653 1808
Manual Extensions lb- 77 - - 77 -- 66 - - 66 -
1 extra valve (hose reels) lb 992 extra valves (hose reels) lb 198
1) Weights ± 5% because of tolerances for plate thickness
Section - 4 25 32 / 222 Technical Specifications Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 - Specifications with Fly-Jib (Metric)32 / 222-K4 + FJ1000 32 / 222-K5 + FJ1000
Performance Unit FJ K3 FJ K4 FJ K5 FJ K3 FJ K4 FJK5Hydraulic reach m 20,38 22,20 24,19 22,48 24,30 26,29Hydraulic telescopic movement, Fly-jib mm 5005 6745 8730 5005 6745 8730
Out-reach with manual extensions m 24,21 - 26,29 -
Lifting capacity, hydraulic kg-m
1110-15,5980-16,9835-18,5790-20,4
1065-15,4940-16,9835-18,5750-20,4685-22,2
995-15,4870-17,0770-18,6685-20,4565-24,2
800-17,4710-19,0640-20,6575-22,4
750-17,4660-19.0590-20,6530-22,4480-24,2
685-17,5600-19,1530-20,7470-22,5420-24,3345-26,2
Lifting capacity, manual exten-sions kg-m - 565-24,2
485-26,1 - 365-26,2285-28,2 - -
Dimensions:Height above chassis-with winch mm 2678
Height above chassis- excl. winch mm 2668
Width mm 2500Length, without extra valve kit on fly-jib mm 1172
Length, with extra valve kit on fly-jib mm 1172
Weights:Fly-jib 1) 680 760 830 670 750 820
Manual Extensions - 35 - - 35 -- 30 - - 30 -
1 extra valve (hose reels) 452 extra valves (hose reels) 90
1) Weights ± 5% because of tolerances for plate thickness
This page left intentionally blank
26
32 / 222 - Manual # 99905811
Section - 5 27 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
Section - 532 / 222 Capacity Charts Fly-Jibs
Section - 5 30 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 K5 FJ1000 K3 - Capacity Chart
70490017
Model 32/222 K4FJ1000 K3
6'
80°
65°
45°
30°
45°
20º
11352502
10002204
8951973
8051774
13402954
11702579
10402292
9302050
16303593
14053097
12302711
10702358
25805687
21204673
15203351
11252480
28506283
15203351
20254465
28506283
22304916
15503417
11502535
28506283
24105313
18654111
12902843
9502094
KGLB
0MOUNTINGSURFACE
12'6'(1.83 m)
18'12'(3.66 m)
24'18'(5.49 m)
30'24'(7.32 m)
30'(9.14 m)
36'(10.97 m)
42'(12.80 m)
48'(14.63 m)
54'(16.46 m)
60'(18.29 m)
72'(21.95 m)
66'(20.12 m)
78'(21.95 m)
6'(1.8 3 m)
0CENTERLINE
18'(5.49 m)
12'(3.66 m)
30'(9.14 m)
24'(7.32 m)
42'(12.80 m)
36'(10.97 m)
54'(16.46 m)
48'(14.63 m)
66'(20.12 m)
60'(18.29 m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 28 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 K4 FJ1000 K4 - Capacity Chart
70490139
Model 32/222 K4FJ1000 K4
78'(21.95 m)
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
30°
800*
570*
540*
515*
485*
470*930
670*88511102540 2080 1500
635*84010501585 1365 1195
605*8058901295 1130 1000
940*
1205
570*7007701090 960 855
555*7402370 1845 1265
2005
1500
20°
80°
65°
45°
45°
0 2370 1845 1265 930 740 555* 470*
1090 960 855 770 700 570* 485*
5225
2403 2116 1885 1698 1543 1257* 1069*
4068 2789 2050 1631 1224* 1036*
12952855
11302491
10002205
8901962
8051775
605*1334*
515*1135*
15853494
13653009
11952635
10502315
237052258401852
540*1190*
635*1400*
25405600
20804586
15003307
11102447
8851951
670*1477*
570*1257*
28506283
28355225
28506283
20054420
15003307
12052657
940*2072*
800*1764*
22104872
15303373
11352502
9051995
690*1521*
585*1290*
0(2m) (4m) (6m) (8m) (10m) (12m) (14m) (16m) (18m) (20m)
(22m)
(24m)
(26m)
(28m)
13’ 1”
(4m)13’ 1”
19’ 7”
(6m)19’ 7”
26’ 2”
(8m)26’ 2”
32’ 8”
(10m)32’ 8”
39’ 4”
(12m)39’ 4”
45’ 9”
(14m)45’ 9”
52’ 5”
(16m)52’ 5”
59’ 1”
(18m)59’ 1”
65’ 6”
(20m)65’ 6”
72’ 2”
78’ 7”
85’ 3”
91’ 9”
(30m)98’ 4”
(26m)(24m)(22m) (28m)85’ 3”78’ 7”72’ 2” 91’ 9”6’ 6”
(2m)6’ 6”
* With Manual Extension
KGLB
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONS
YBETADNOITPIRCSEDOCEVER
70490139
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
A
FULL4-9-2018 DECAL- CP 32/222K4 / FJ1000 K4
Section - 5 29 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 K4 FJ1000 K5 - Capacity Chart
70490142
Model 32/222 K4FJ1000 K5
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
0(2m) (4m) (6m) (8m) (10m) (12m) (14m) (16m) (18m) (20m)
(22m)
(24m)
(26m)
(28m)
13’ 1”
(4m)13’ 1”
19’ 7”
(6m)19’ 7”
26’ 2”
(8m)26’ 2”
32’ 8”
(10m)32’ 8”
39’ 4”
(12m)39’ 4”
45’ 9”
(14m)45’ 9”
52’ 5”
(16m)52’ 5”
59’ 1”
(18m)59’ 1”
65’ 6”
(20m)65’ 6”
72’ 2”
78’ 7”
85’ 3”
91’ 9”
(26m)(24m)(22m)85’ 3”78’ 7”72’ 2”6’ 6”
(2m)6’ 6”
30°
865
2850
67582010402455 2005 1425
6407759801515 1290 1125
6107408251220 1060 930
940
1135
5756357001020 890 785
5606802285 1760 1195
1915
1425
20°
80°
65°
45°
45°
22855038
17603880
11952635
8651907
6801499
5601235
10202249
8901962
7851731
7001543
6351400
5751268
15153340
12902844
11252480
9802161
7751709
6401411
24555412
20054420
14253142
10402293
8201808
6751488
28506283
21154663
14553208
10652348
8401852
6901521
28506283
21154663
28506283
14553208
10652348
8401852
6901521
27256008
19154222
14253142
25025225
9402072
KGLB
Section - 5 31 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 K5 FJ1000 K2 - Capacity Chart
Model 32/222 K5FJ1000 K2
22154883
12852833
8751929
10202245
6'(1.8 3 m)
0CENTERLINE
18'(5.49 m)
12'(3.66 m)
30'(9.14 m)
24'(7.32 m)
42'(12.80 m)
36'(10.97 m)
54'(16.46 m)
48'(14.63 m)
66'(20.12 m)
60'(18.29 m)
72'(21.95 m)
0MOUNTING SURFACE
6'(1.83 m)
12'(3.66 m)
18'(5.49 m)
24'(7.32 m)
30'(9.14 m)
36'(10.97 m)
42'(12.80 m)
48'(14.63 m)
54'(16.46 m)
60'(18.29 m)
72'(21.95 m)
66'(20.12 m)
84'(25.60 m)
78'(21.95 m)
80°
65°
45°
45°
20º30°
KGLB
8751929
7801720
7051555
10652348
9452083
8451863
13352943
11702580
9902183
22354927
15153400
10402293
26305800 3417
1550 10652348
26305800 1995
440014003086
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONS
REV ECO DESCRIPTION DATE BY
70399939
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
A
FULL02/08/2016 DECAL- CP 32/222 K5/J1000K2
A 9000 KJB12/19/2013Changed model description
70399939
Section - 5 32 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 K5 FJ1000 K4 - Capacity Chart
70490143
Model 32/222 K5FJ1000 K4
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
00
(2m) (4m) (6m) (8m) (10m) (12m) (14m) (16m) (18m) (20m)
(22m)
(24m)
(26m)
(28m)
13’ 1”
(4m)13’ 1”
19’ 7”
(6m)19’ 7”
26’ 2”
(8m)26’ 2”
32’ 8”
(10m)32’ 8”
39’ 4”
(12m)39’ 4”
45’ 9”
(14m)45’ 9”
52’ 5”
(16m)52’ 5”
59’ 1”
(18m)59’ 1”
65’ 6”
(20m)65’ 6”
72’ 2”
78’ 7”
85’ 3”
91’ 9”
(30m)98’ 4”
(32m)105’ 0”
(34m)111’ 5”
(26m)(24m)(22m) (28m)85’ 3”78’ 7”72’ 2” 91’ 9”
(30m)98’ 4”6’ 6”
(2m)6’ 6”
* With Manual Extension
45
30
65
80
20
45
750 660 590 530 480 365*
650740830
290*
21554751
12302712
8201808
5951312
4701036
360*794*
280*617*
7501653
6601455
5901301
5301168
4801058
365*805*
9452083
8301830
7401631
6501433
280*617*
5151135
410*904*
310*683*
12202690
10602337
9302050
6801499
5401190
435*959*
330*728*
21304696
14553208
9852172
7201587
5701257
470*1036*
350*772*
25705666
25705666
14903285
10102227
7401631
5851290
485*1069*
360*794*
19304255
13402954
9952194
7951753
670*1477*
510*1124*
KGLB
Section - 5 33 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 K5 FJ1000 K5 - Capacity Chart
70490144
Model 32/222 K5FJ1000 K5
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
00
(2m) (4m) (6m) (8m) (10m) (12m) (14m) (16m) (18m) (20m)
(22m)
(24m)
(26m)
(28m)
13’ 1”
(4m)13’ 1”
19’ 7”
(6m)19’ 7”
26’ 2”
(8m)26’ 2”
32’ 8”
(10m)32’ 8”
39’ 4”
(12m)39’ 4”
45’ 9”
(14m)45’ 9”
52’ 5”
(16m)52’ 5”
59’ 1”
(18m)59’ 1”
65’ 6”
(20m)65’ 6”
72’ 2”
78’ 7”
85’ 3”
91’ 9”
(28m)98’ 4”
(26m)(24m)(22m)85’ 3”
(28m)91’ 9”78’ 7”72’ 2”6’ 6”
(2m)6’ 6”
2050
45
65
80
45
30
20
20504519
11552546
7601676
5351179
410904
330728
6851510
6001323
5301168
4701036
420926
345761
8751929
7601676
6701477
5901301
4551003
370816
11502535
9902183
8601896
6201367
4751047
390860
20504519
13803042
9202028
6951532
5201146
415915
24505401
24505401
18354045
14103109
9452083
6251378
5251157
430948
12652789
9252039
7301609
6001323
Section - 5 34 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
32 / 222 Lifting Capacity, Fly Jib with Winch
SLAW
0°
FJ-Amax
FJ-SLAmax
FJ-SLAmin
HJAW
(HJAW)
Not recommendedworking angle.
SLAW
Section - 5 35 32 / 222 Capacity Charts Fly-Jibs
32 / 222 - Manual # 99905811
Lifting Capacity, Fly Jib with Winch-Continued
Lifting capacity for hoist
Max. Angle
Recommended working area
(SLAW)
Hydraulic Hoist Type
1500 kg(Dinamic P9E)
2500 kg(Dinamic P15E)
3200 kg Dinamic S25 Brevini 2500
FJ Amax
FJ-Sl Amin
FJ-Sl Amax
HJAW(LB)
SLAW(LB)
HJAW(LB)
SLAW(LB)
HJAW(LB)
SLAW(LB)
FJ350 70° -30° 30° 1328 2205FJ1000 70° -30° 30° 1543 4079FJ1200 70° -40° 40° 2205 7055FJ2000 70° -40° 40° 2866 7055
Hydraulic Hoist Type (Metric)FJ350 70° -30° 30° 600 kg 1000 kgFJ1000 70° -30° 30° 700 kg 1850 kgFJ1200 70° -40° 40° 1000 kg 3200 kgFJ2000 70° -40° 40° 1300 kg 3200 kg
Section - 6 36 32 / 222 Dimension Drawings with Fly-Jib
32 / 222 - Manual # 99905811
Section - 632 / 222 Dimension Drawings with Fly-Jib
Section - 6 37 32 / 222 Dimension Drawings with Fly-Jib
32 / 222 - Manual # 99905811
32 / 222 - Dimension Sketch, K5 with FJ1000
2668
320CL CHASSIS
=
802
1789
2506
2848
K5 + FJ1000 K5:K5 + FJ1000 K5:
7791, Max.Max.
26335
1357
5151
6
25008’ 2”
3’ 3”
0.24”
=
1172
1009
427
TOP CHASSIS
31.6
”
16.8”
3’ 8”
8’ 8
”
12.6”
16’ 9”
4’ 5
”
25’ 6” 86’ 4”
5’ 9
”
9’ 3
”
8’ 2
”
Section - 6 38 32 / 222 Dimension Drawings with Fly-Jib
32 / 222 - Manual # 99905811
Dimension Sketch, K5 with FJ1000-continued
2678
30
= =
5151
2500
320CL CHASSIS
8’ 2”
12.6”
1.2”
8’ 8
”
16’ 9”4’
3”
1300
This page left intentionally blank
39
32 / 222 - Manual # 99905811
Section - 7 40 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
Section - 732 / 222 Hydraulic Drawings
Section - 7 41 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Hydraulic Diagram, Danfoss Single-Circuit Crane Functions
C2 C1
V2 V1
5904
4
PVP
T
P
LS M
A-PORT
A-PORT
A-PORT
A-PORT
A-PORT
A-PORT
55601/55605/55609
P PVSKPst
A1 B1
A B
5526
3
MA1
V1 V2
HPCO
OPTIONAL
B1
M3
BA
M2M1A1
55227
X1
X3
X2
X4
A
B
55602/55606/55610
OPTIONAL
A
B
A
B
A
B
A
B
A
B
4917
2
OPTIONAL
Section - 7 42 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Hydraulic Diagram, Danfoss, Single-Circuit FJ with EXV + Winch
Pst
P PVSK
PVP
A-PORT
A-PORT
A-PORT
A-PORT
A-PORT
A-PORT
A-PORT
A-PORT
T
P
LS M
A-PORT
OPTIONAL
P1
P2
C1C2
C3C4 59062
P1
P2
C1C2
C3C4 59062
V1 V2
OPTIONAL
A
B
A
B
A
B
A
B
A
B
A
B
A
B
OPTIONAL
HPCO
5902
7/55
221
MM2M1 C1C2
V1V2
C2 C1
V2 V1
5902
2
X1 X3X2 X4
5828
5
55604/55608/55612
55603/55607/55611 OPTIONAL
Section - 7 43 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Hydraulic Diagram, Danfoss Single-Circuit Variable & Fixed
PVP
T
P
LS M
A-PORT
A-PORT
A-PORT
A-PORT
P PVSK
PstHPCO
A
B
OPTIONAL
A
B
A
B
A
B
4921
6
1 2 3 4
1 2 3 4
P
T
T
Pst
Tst
6340844
LS
OPT
ION
AL
HPCO
Section - 7 44 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Hydraulic Diagram, Stabilizer Circuit + 4 FCTS.
50510
TstPst
Ext. Stb.
A9
A10
A11
A12
EXT
OPTIONAL
OPTIONAL
OPTIONAL
HP
CO
5523
9
5849
6
58496
Section - 7 45 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Pressure Setting Diagram
WORKING PRESSURE ON MAIN RELIEF VALVE & PORT RELIEF VALVES
Function Direction Port
Port Relief Valves(PSI)
LS Pressure Adj.(PSI
Main Relief Valve 5657
Slewing System RightLeft
AB
PP
21762176
Boom Cyinder UpDown
AB
55111813
52941450
Jib Cylinder UpDown
AB
55112900
52942538
Extension Cylinders ExtendRetract
AB
PP
43514351
Grab UpDown
AB
4351**4351**
725-4351*725-4351*
Rotator ExtendRetract
AB
PP
725-4351*725-4351*
Winch 2.5T LiftLower
AB
PP
26832683
Separate Stabilizer Valve All 2176
*Individual adjustment of LS-Pressure possible on loaders without Fly-Jib. See settings of pressure for Fly-Jib.**On loaders with Fly-Jib port relief valves, please see Working Pressure on Fly-Jib Table**On loaders without Fly-Jib, individual replacement of port relief valves is possible.
WORKING PRESSURE ON LOAD HOLDING VALVES
Function DirectionOpening Pressure
(PSI)Slewing System Right
Left23212321
Boom Cylinder UpDown
5511-
Jib Cylinder Up Down
55113046
Extension Cylinders RetractExtend
62373046
PRESSURE SETTING FOR LOAD MOMENT LIMITATION (LMB)Load Moment Limitation (LMB) (PSI) 5076HDL (PSI) 4061
MAXIMUM PUMP PERFOMANCEChoice of Pump Fixed VariablePump Performance (gpm) 21 29
Section - 7 46 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Pressure Setting Diagram, Fly-Jib
WORKING PRESSURE ON FLY-JIB
Function Direction Port
32/222K6FJ600(PSI)
32/222K6FJ1000(PSI)
Mai
n R
elie
f Val
ve LS Pressure Adjustment UpDown
AB
40603626
32633626
Port Relief Valves Up Down
AB
43514351
36264351
Load Holding Valves UpDown
47863916
39894206
Ext
ensi
on C
ylin
ders
LS Pressure Adjustment ExtendRetract
AB
43514351
43514351
Load Holding Valve ExtendRetract
30466237
30466237
Load Moment Limitation
(LMB)3916 3118
Section - 7 47 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Pressure Setting Diagram (Metric)
WORKING PRESSURE ON MAIN RELIEF VALVE & PORT RELIEF VALVES
Function Direction Port
Port Relief Valves(PSI)
LS Pressure Adj.(PSI
Main Relief Valve 390
Slewing System RightLeft
AB
PP
150150
Boom Cyinder UpDown
AB
380125
365100
Jib Cylinder UpDown
AB
380200
365175
Extension Cylinders ExtendRetract
AB
PP
300300
Grab UpDown
AB
300**300**
50-300*50-300*
Rotator ExtendRetract
AB
PP
50-300*50-300*
Winch 2.5T LiftLower
AB
PP
185185
Separate Stabilizer Valve All 150
*Individual adjustment of LS-Pressure possible on loaders without Fly-Jib. See settings of pressure for Fly-Jib.**On loaders with Fly-Jib port relief valves, please see Working Pressure on Fly-Jib Table**On loaders without Fly-Jib, individual replacement of port relief valves is possible.
WORKING PRESSURE ON LOAD HOLDING VALVES
Function DirectionOpening Pressure
(PSI)Slewing System Right
Left23212321
Boom Cylinder UpDown
5511-
Jib Cylinder Up Down
55113046
Extension Cylinders RetractExtend
62373046
PRESSURE SETTING FOR LOAD MOMENT LIMITATION (LMB)Load Moment Limitation (LMB) (PSI) 5076HDL (PSI) 4061
MAXIMUM PUMP PERFOMANCEChoice of Pump Fixed VariablePump Performance (gpm) 21 29
Section - 7 48 32 / 222 Hydraulic Drawings
32 / 222 - Manual # 99905811
32 / 222 - Pressure Setting Diagram, Fly-Jib (Metric)
WORKING PRESSURE ON FLY-JIB
Function Direction Port
32/222K6FJ600(PSI)
32/222K6FJ1000(PSI)
Mai
n R
elie
f Val
ve LS Pressure Adjustment UpDown
AB
280250
225250
Port Relief Valves Up Down
AB
300300
250300
Load Holding Valves UpDown
330270
275290
Ext
ensi
on C
ylin
ders
LS Pressure Adjustment ExtendRetract
AB
300300
300300
Load Holding Valve ExtendRetract
210430
210430
Load Moment Limitation
(LMB)270 215
This page left intentionally blank
49
32 / 222 - Manual # 99905811
IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.
IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2019 Iowa Mold Tooling Co., Inc. All Right Reserved.
IOWA MOLD TOOLING CO., INC.
P.O. Box 189 Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com