EXCLUSIVE OUTDOOR FLOORING 300 x 600 Woven Tile dimensions (finished product with grid): 300 x 600 x 31 mm CHECKERBOARD pattern Hortus Tile 300 x 600 checkerboard pattern Surface covered: 1,44 m 2 approx. INSTALLATION (CHECKERBOARD pattern) In order to install the 7 th and the 8 th tile, seeing that you find on the right side male joints (3 rd and 4 th tile) and on the left side female joints (6 th tile), before it’s necessary to lift up the tiles with the male joints in order to make slide under them the female joints on the long side of the tile which you are laying and then to insert the male joints on its short side into female joints of 6 th tile. Example shows correctly installed floor. Continue in the way previously illustrated for all the following tiles until to the end of installation. 10 9 Click the male joints on the long side of the grid of the 2 nd tile into the female joints on the long side of the grid of the 1 st tile. 2 Lay the first tile in a corner of the area to be covered taking care to place the long side of the grid with the female joints towards the area where you want to lay the floor. 1 Install the 3 rd and the 4 th tile insuring to place the strips composing tiles in perpendicular way compared to the ones of the first two tiles laid. 3 In order to insert the female joints on the long side of the tile which you are laying into the male joints on the short side of the first 2 tiles laid, lift slightly up the short sides of the first two tiles laid in order to allow to the female joints of the tile which you are laying to slide under it. 4 Fasten the 4 th tile lifting up the long side with the male joints of the 3 rd tile just laid in order to allow to the female joints of the tile which you are laying to slide under them. Install the 5 th and 6 th tile inserting the male joints on the short side of the tiles which you are laying into the female joints on the long side of the 2 nd tile laid. Fasten the 6 th tile with the 5 th inserting the male joints on the long side of the 6 th tile into the female joints on the long side of the 5 th tile. 6 5 Verify that all the laid tiles create some squares of 60 x 60 cm. In order to make this, place two tiles with the strips parallel and then lay the neighbouring tiles with the strips put in perpendicular way. 7 Lay the 7 th and the 8 th tile taking care that the strips are placing in perpendicular way compared to the ones of the neighbouring tiles. 8 www.hortusfloor.it

300 x 600 Woven Tile - Hortus Floor...300 x 600 checkerboard pattern Surface covered: 1,44 m2 approx. INSTALLATION (CHECKERBOARD pattern) In order to install the 7th and the 8th tile,

Download PDF Report

Upload
others
View
1
Download
0

Embed Size (px)

Citation preview

Page 1: 300 x 600 Woven Tile - Hortus Floor...300 x 600 checkerboard pattern Surface covered: 1,44 m2 approx. INSTALLATION (CHECKERBOARD pattern) In order to install the 7th and the 8th tile,

EXCLUSIVE OUTDOOR FLOORING

300 x 600 Woven Tiledimensions (finished product with grid): 300 x 600 x 31 mm

CHECKERBOARDpattern

Hortus Tile 300 x 600

checkerboard pattern

Surface covered: 1,44 m2 approx.

INSTALLATION (CHECKERBOARD pattern)

In order to install the 7th and the 8th tile, seeing that you find on the right side male joints (3rd and 4th tile) and on the left side female joints (6th tile), before it’s necessary to lift up the tiles with the male joints in order to make slide under them the female joints on the long side of the tile which you are laying and then to insert the male joints on its short side into female joints of 6th tile.

Example shows correctly installed floor. Continue in the way previously illustrated for all the following tiles until to the end of installation.

109

Click the male joints on the long side of the grid of the 2nd tile into the female joints on the long side of the grid of the 1st tile.

Lay the first tile in a corner of the area to be covered taking care to place the long side of the grid with the female joints towards the area where you want to lay the floor.

Install the 3rd and the 4th tile insuring to place the strips composing tiles in perpendicular way compared to the ones of the first two tiles laid.

In order to insert the female joints on the long side of the tile which you are laying into the male joints on the short side of the first 2 tiles laid, lift slightly up the short sides of the first two tiles laid in order to allow to the female joints of the tile which you are laying to slide under it.

Fasten the 4th tile lifting up the long side with the male joints of the 3rd tile just laid in order to allow to the female joints of the tile which you are laying to slide under them.

Install the 5th and 6th tile inserting the male joints on the short side of the tiles which you are laying into the female joints on the long side of the 2nd tile laid. Fasten the 6th tile with the 5th inserting the male joints on the long side of the 6th tile into the female joints on the long side of the 5th tile.

Verify that all the laid tiles create some squares of 60 x 60 cm. In order to make this, place two tiles with the strips parallel and then lay the neighbouring tiles with the strips put in perpendicular way.

Lay the 7th and the 8th tile taking care that the strips are placing in perpendicular way compared to the ones of the neighbouring tiles.

www.hortusfloor.it