27
Enterasys Networks 2B0-011 ES Router Configuration Version 1.0

2B0-011 1-0

Embed Size (px)

DESCRIPTION

command

Citation preview

Enterasys Networks 2B0-011ES Router ConfigurationVersion 1.0

QUESTION NO: 1 Which CLI command associates an interface to an OSPF area?

A. interface set to-area B. area add interface C. ospf add interface to-area D. interface add ospf to-area

Answer: C

QUESTION NO: 2 Which command can change the X-Pedition Router system contact name to "User One?

A. system set administrator User_OneB. system set contact "User One"C. set User_One system nameD. set system name "User One"

Answer: B

QUESTION NO: 3 Which command displays the IP Route Table on the X-Pedition Router?

A. show routes allB. ip-router show route-tableC. ip show routesD. show ip route-table

Answer: C

QUESTION NO: 4 Which one of the following statements best describes the L2 operation of the X-Pedition Router?

A. It acts as a Store and Cut-Through switch.B. It acts as a Store and Forward switch.C. It acts as a Simple Cut-Through switch.D. It acts as an Adaptive Cut-Through switch.

Answer: B

QUESTION NO: 5 Which two types of VLANs may be created on the X-Pedition Router?

A. AccessB. TrunkC. Port-BasedD. Protocol-Based

Answer: C,D

QUESTION NO: 6 Which command implements QoS weighted Fair Policy?

A. set qos queuing-policy weighted-fairB. queuing-policy set qos weighted-fairC. set weighted-fair queuing-policy qosD. qos set queuing-policy weighted-fair

Answer: D

QUESTION NO: 7 In bootprom mode, which command displays the X-Pedition Router configuration files on the internal flash?

A. ls /bootup/pc-flash/B. ls /int-flash/cfg/C. file dir int-flash/cfg/D. system show bootup/cfg/

Answer: B

QUESTION NO: 8 Which command in enable mode displays the files in the int-flash/cfg/ directory?

A. system dir slot0:B. file dir bootflash:C. system show bootflash:D. file dir slot0:

Answer: B

QUESTION NO: 9 What is the default output-mac-encapsulation for an IPX interface on the X-Pedition Router?

A. ethernet_snapB. ethernet_802.3C. ethernet_802.2D. ethernet_ii

Answer: D

QUESTION NO: 10 What is the slot numbering scheme for the XP8000 (formerly the SSR8000)?

A. bottom left slot 0 to top right slot 8B. bottom right slot 0 to top left slot 8C. bottom left slot 0 to top right slot 7D. bottom right slot 0 to top left slot 7

Answer: C

QUESTION NO: 11 Which command example enables RIPv2 on an interface?

A. rip add interface 172.16.1.1 version 2B. rip set 172.16.1.1 version 2C. rip set interface 172.16.1.1 version 2D. rip add 172.16.1.1 version 2

Answer: C

QUESTION NO: 12 What of the following would cause the X-Pedition Router to go into Boot Prom Mode?

A. a loss of powerB. an invalid startup configuration during bootupC. Removing the PCMCIA card when the control module is operatingD. an invalid system image during bootup

Answer: C,D

QUESTION NO: 13 Which two of the following descriptions are characteristics of the X-Pedition Router?

A. The addition of new interfaces affects routing performanceB. Forwarding and lookups are performed on each individual moduleC. Routing is performed by hardwareD. Implementing Quality of Service and/or security Access Control Lists decreases performance

Answer: B,C

QUESTION NO: 14 Which CLI command defines an ospf area as a Stub Area?

A. ospf set area stubB. ospf add interface stubC. ospf create stub-area D. interface set ospf area stub

Answer: A

QUESTION NO: 15 Which command displays the detailed information of all RIP packets sent and received?

A. rip trace packets sent-receivedB. rip trace received requestC. rip trace packets detailD. rip trace sent packets

Answer: C

QUESTION NO: 16 How many Queue Priority Levels are on the router?

A. 3B. 2C. 4D. 1

Answer: C

QUESTION NO: 17 Which command example configures a default route on the X-Pedition Router?

A. ip create route default nexthop 10.10.20.1B. ip add route default gateway 10.10.20.1C. ip create route default gateway 10.10.20.1D. ip add route default nexthop 10.10.20.1

Answer: B

QUESTION NO: 18 When multiple images are on an X-Pedition Router, which command selects the next boot image?

A. system image choose B. system select image C. system choose version D. system image select version

Answer: A

QUESTION NO: 19 What are the three major steps required to create a L3 Protocol-based VLAN?

A. Create the VLAN, add physical ports to the VLAN, and add IP/IPX address to the VLANB. Create the VLAN, make the trunk port, and assign a policyC. Create the VLAN, add physical ports, and assign a policyD. Create the VLAN, make the trunk port, and add an IP address to the VLAN

Answer: A

QUESTION NO: 20 Which of the following protocols does the X-Pedition Router route?

A. IP, IPX, DECnet, and Vines; all other protocols bridgedB. IP, IPXC. IP, IPX and AppleTalk routed by ASICs; DECnet and Vines routed by softwareD. IP only; all other protocols bridged

Answer: B

QUESTION NO: 21 Which of the following types of vlans are supported?

A. ip, ipx, port-based, and bridged-protocolsB. mac-based, policy-based, ip and ipxC. ip, ipx, icmp, and arpD. ipx, dec, apollo, and net-bios

Answer: A

QUESTION NO: 22 Which method can be used to enter Boot Prom mode on the X-Pedition Router?

A. Press ESC key while bootingB. Type Boot-Prom command in Enable modeC. Press ^Z keys while bootingD. Press ^C keys while booting

Answer: A

QUESTION NO: 23 Which command copies the default startup file to a backup file in ROM Monitor mode?

A. copy /int-flash/cfg/startup /int-flash/cfg/backupB. copy /startup.cfg /backup.cfgC. cp /startup/cfg /backup/cfgD. cp /int-flash/cfg/startup /int-flash/cfg/backup

Answer: D

QUESTION NO: 24 Which command sets access privileges for remote SNMP management?

A. set community snmp privilegeB. system set snmp community C. snmp set community privilege < keyword>D. snmp set target community status enable

Answer: C

QUESTION NO: 25 Which CLI command is used to create the OSPF backbone?

A. interface create ospf area backboneB. ospf create area backboneC. ospf area 0.0.0.0 create interface D. ip-router create ospf area 0.0.0.0

Answer: B

QUESTION NO: 26 Which one of the following would be found in an OSPF Stub Area?

A. One or more Virtual LinksB. An Autonomous System Boundary RouterC. At least one Area Border RouterD. OSPF-ASE Routes

Answer: C

QUESTION NO: 27 Which CLI command defines an OSPF router-id?

A. router-id set interface globalB. ip-router global set router-id C. interface set router-id globalD. global set router-id

Answer: B

QUESTION NO: 28 Which command displays the output of the RIP Trace command on the terminal monitor?

A. ip-router set trace-state onB. rip trace startC. set rip trace-state onD. rip trace on

Answer: A

QUESTION NO: 29 Which prompt indicates Enable mode?

A. >B. #C. (enable)D. !

Answer: B

QUESTION NO: 30 What is the first step to gain access to an X-Pedition Router when the password is unknown?

A. Press CTRL+ALT+DELB. Power cycle the router and press the ESC key to enter BootROM mode.C. Rename the active file to bootupD. Press the ESC key

Answer: B

QUESTION NO: 31 What is the X-PEDITION Router's default metric for redistributing routes into RIP?

A. 14B. 16C. 1D. 0

Answer: B

QUESTION NO: 32 When an L3 interface is created on the X-Pedition Router and associated with a single port, which type of VLAN is created?

A. Implicit Port basedB. No VLAN is created or requiredC. Implicit Subnet basedD. Explicit Bridged-Protocol based

Answer: C

QUESTION NO: 33 What is the second step to gain access to an X-Pedition Router when the password is unknown?

A. Power cycle the routerB. Copy the startup file to a backupC. Rename the active file to bootupD. Press CTRL+ALT+DEL

Answer: B

QUESTION NO: 34 Which two L3 multicast routing protocols does the X-Pedition Router support?

A. EIGRPB. IGRPC. PIM-SMD. DVMRP

Answer: C,D

QUESTION NO: 35 Which CLI command would configure an IP address to the loopback interface?

A. ip add interface loopback0 address-netmask B. interface add ip lo0 address-netmask C. interface create ip lo0 address-netmask D. interface set ip loopback0 address-netmask

Answer: B

QUESTION NO: 36 Which command displays the contents of a stored configuration file on the monitor screen?

A. system type B. system show C. file type D. file show

Answer: C

QUESTION NO: 37 Which two types of VLAN ports are supported on the X-Pedition Router?

A. Access and TrunkB. Control and HybridC. Access and Full DuplexD. Trunk and Control

Answer: A

QUESTION NO: 38 During the boot process, what are all the physical ports initially added to?

A. default VLANB. configured VLANC. Physical ports are not detected during boot processD. protocol-based VLAN

Answer: A

QUESTION NO: 39 Which type of VLAN does the X-Pedition Router define that works at L3?

A. SNAB. DECnet and IPv6C. Bridged-ProtocolsD. IP and IPX

Answer: D

QUESTION NO: 40 What are the two Queuing Management policies on the X-Pedition Router?

A. Control Policy, Weighted Fair QueuingB. Control Policy, Precedence PolicyC. Strict Priority, Control PolicyD. Strict Priority, Weighted Fair Queuing

Answer: D

QUESTION NO: 41 Which command example configures a primary IP address on an interface on the router?

A. interface add ip eth6 address-netmask 172.16.1.1/24B. interface create ip eth6 address-netmask 172.16.1.1/24 port et.1.6C. interface create ip eth6 address-netmask 172.16.1.1/24D. interface add ip eth6 address-netmask 172.16.1.1/24 port et.1.6

Answer: B

QUESTION NO: 42 Which X-Pedition Router command copies the startup configuration file to a server?

A. copy active to B. copy startup to C. copy active to tftp-serverD. copy startup to tftp-server

Answer: D

QUESTION NO: 43 Which two methods can be used to load an operational system image to the X-Pedition Router?

A. Load from a file in the in the int-flash/cfg/ directoryB. Load from a file in the pc-flash/boot/ directoryC. Load from a file on an FTP ServerD. Load from a file on a TFTP Server

Answer: B,D

QUESTION NO: 44 Which CLI command is necessary to begin the OSPF process?

A. start ospfB. enable ospf state onC. ospf startD. ospf set enable

Answer: C

QUESTION NO: 45 QoS policies can be written using information contained in which three layers of the OSI model?

A. Transport Layer, Session Layer and Application LayerB. Physical Layer, DataLink Layer and Network LayerC. DataLink Layer, Network Layer and Transport LayerD. Network Layer, Transport Layer and Application Layer

Answer: C

QUESTION NO: 46 Which command is used to transfer an image to the X-Pedition Router?

A. system ftp image B. system image add tftp-server file-name C. copy ftp flash D. copy image flash

Answer: B

QUESTION NO: 47 Which of the following commands will configure RIP on an IPX interface?

A. rip add interface allB. no command is required, rip starts when the ipx interface is createdC. rip add interface D. rip add interface

Answer: B

QUESTION NO: 48 What does the command system show version display?

A. the Boot Prom version and software versionB. the printed circuit board revisionC. the image selected for next bootD. the hardware and software version of the Line Cards

Answer: A

QUESTION NO: 49 Which command example configures a static route on the X-Pedition router?

A. ip add route 172.16.20.1/24 nexthop 172.16.10.1B. ip create route 172.16.20.1/24 nexthop 172.16.10.1C. ip create route 172.16.20.1/24 gateway 172.16.10.1D. ip add route 172.16.20.1/24 gateway 172.16.10.1

Answer: D

QUESTION NO: 50 Which command (from Enable mode) saves the current running configuration to the startup configuration file?

A. copy active to startupB. save active to startupC. copy scratchpad to startupD. copy running-config to startup-config

Answer: A