WARNINGWear protective eyewear.

Failure to may result in severe burns or longterm injury to the eyes.

DANGERShock hazard.

Disconnect power before servicing or removing any protec-tive covers.

Do not operate this device near water or while you are wet.

DANGERSome medications may increase your sensitivity to ultraviolet light. Itis recommended that you consult a physician before using thissunbed if taking any medication or if you suspect that your skin mightbe especially sensitive to sunlight.

CAUTIONUse of a voltage source above 230V AC may prevent proper operationof the sunbed and could cause damage and void the warranty.

Air from the room is used to cool the sunbed. Maximum ambient roomtemperature should be 80°F. Place your sunbed no closer than 6” fromany wall. Make sure nothing obstructs the airflow into the sunbed’sendcaps or out of the fan openings. A poorly ventilated room maycause the unit to become hot and cause discomfort to the user.

29237-01A - Page 1

Ultraviolet radiation. Follow instructions. Avoid overexposure. As withnatural sunlight, overexposure can cause eye and skin injury and

allergic reactions. Repeated exposure may cause premature aging of the skin and skin cancer.WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS ORLONGTERM INJURY TO THE EYES. Medications or cosmetics may increase your sensitivityto the ultraviolet radiation. Consult physician before using sunlamp if you are using medicationsor have a history of skin problems or believe yourself especially sensitive to sunlight. If you donot tan in the sun, you are unlikely to tan from the use of this product. Children, the elderly, orfair skinned people who always burn easily and either never tan or tan minimally should not usethis equipment.

To use, lie down on bench and pull canopy down as far as adjustment will allow maintainingat least 2 inches (5.1 centimeters) between your body and canopy clear plastic panel, other-wise overexposure may occur. Do not use without clear plastic panels in place. Untanned per-sons should not tan on consecutive days during their first week of tanning. Never tan more thanonce a day. Tanning normally appears after the first few sessions and maximizes after approxi-mately four weeks. Tan once or twice per week thereafter to maintain appearance. Personsalready having a base tan may begin at advanced levels corresponding to the extent of theirbase tan.Skin Type:I Sensitive Skin (Burns easily and severely and does not tan.)II Light Skin (Burns easily and severely and tans minimally.)III Normal Skin (Burns moderately and tans average.)IV Dark Skin (Burns minimally, tans easily and above average.)

New lamps emit approximately 10% more ultraviolet radiation during the first 50 hours ofoperation. Recommended tanning times should therefore be reduced by approximately 10%during that period.

WARNING: • Read these instructions before using this sunlamp product. • All persons in theroom should wear protective eyewear when lamps are on. Recommended eyewear: providedeyeshields or equivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewearmay not provide adequate protection. Failure to use protective eyewear may result in severeburns or other eye injury. If discomfort develops, discontinue use and consult a physician.ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE 28 2F:PS MAX Wolff® Model PSM71-T12-100W BI-PIN (� below) -or- DARK TAN™ Wolff® Model DT71-T12-100W BI-PIN (� below)

PS EXTREME Wolff® Model PSE71-T12-100W BI-PIN (� below) -or- DARK TAN™ PLUS Wolff® Model DTP71-T12-100W BI-PIN (� below)

Heraeus E400 HPT, Philips Model HPA 400/30s or CosmoTech Model 23045(Facial Lamps)

THIS EQUIPMENT MUST BE EARTH GROUNDED.

This product is in conformity with performance standardsfor sun lamp products under 21 CFR PART 1040.20 andANSI/UL Standard 482.

88465

DISCONNECT POWER CORD BEFORE ATTEMPTING TO CLEAN, RELAMP, ORENGAGE IN THE MAINTENANCE OF THIS PRODUCT.

DANGER

RECOMMENDED EXPOSURE TIMES IN MINUTESLevel 1/Week 1 Level 2 Level 3 Level 4 Level 5

Skin Type: 1st-3rd SessionsI Sensitive NOT RECOMMENDED FOR TANNINGII Light 2 4 6 8 11III Normal 3 5 8 11 11IV Dark 4 6 9 11 11

MAXIMUM EXPOSURE TIME IS 11 MINUTES

Electrical Requirements

Your sunbed operates from a 220V AC source. The 28 2F requires aNEMA L6-30R electrical outlet (below) on a dedicated circuit capableof providing 30 Amp service, installed in the room in which you willuse the unit. We recommend installation by a professional electrician.The outlet must be earth grounded. 30 AMP NEMA #L6-30R

RECEPTACLE

Allen-head Bolt 5/16” x 1”Quantity 2

5/16” Metal WasherQuantity 2

BushingQuantity 2

Allen-head Bolt 5/16” x 1 1/2”Quantity 2

Nylon WasherQuantity 2

Hinge Brackets(1) left, (1) right

Hex (Allen) WrenchQuantity 1

Safety GogglesQuantity 1

Hardware Inventory (These items, Velcro® and a small pillow)

Star Lock WasherQuantity 8#10-32 x 1/2” ScrewQuantity 8

Skirt Retaining BracketQuantity 2

Skirt Mounting Brackets(1) left, (1) right

Page 2 - 29237-01A

Lay the bench upside down on thefloor. Locate the two stand legs.

1Remove the six 5/16” x 1” bolts and5/16” washers installed in the bench.Attach the stand legs, with the four smallskirt mounting holes toward the back, byinstalling the center bolt first. You mayhave to gently push the sides of the legsin to align holes. Tighten with the Allenwrench.

2

SKIRT MOUNTING HOLES

Assembly Procedures

(ELECTRICAL CONNECTORINDICATES BACK OF BENCH)

While the bench is upside-down attach the trian-gular skirt mounting brackets. Locate the twobrackets and attach them as shown with two #10-32 x 1/2” screws and star lock washers. Make surethe threaded inserts point toward the stand legsand the wide end is toward what will be the floor.

3

Attach the side skirts to the mountingbrackets with two #10-32 x 1/2” screwsand star lock washers from inside theskirt and into the brackets. The roundedpart of the side skirts points toward thefront of the bed.

4

The front skirt panel is held in place by adhesive backed Velcro®strips. Clean each place the adhesive will touch with rubbing alcohol(see right). Peel off the backing paper from the two large pieces andadhere them to the stand legs. Stick a long, narrow strip on each sideof the side skirts in the indentation. The last piece attaches the tab onthe top of the front skirt to the bottom of the bench cover.

5

Peel the remaining backing paper from theVelcro strips and press the front skirt in place.

6

VELCRO STRIPS

VELCRO STRIP

SIDE SKIRT

FRONT SKIRT

LEG

RETAINING BRACKET

Using the front leg mounting bolt, securethe L-shaped Skirt Retaining Bracket so itclamps the front and side skirt to thebench cover. Place the retainer bracketso the tab holds the front skirt as shown.Repeat for the other side.

7

PIVOT STUD

CAUTIONFailure to engage locking clips mayresult in the ball joints working loose,allowing the canopy to fall, which mayresult in damage to the unit and injury.

Type 1Pry back thelocking clipwith a flatscrewdriver.

The gas springs have a lockingmechanism. Follow the directionsbelow for the type you received.

12 With a helper holding the canopy open,align ends of gas spring ball joints withpivot studs and push into place. Be surerod end is down as shown. DO NOT lowercanopy until both gas springs are engaged!

13

Lift and lower canopy a fewtimes to lubricate gas springsfor optimum performance.

14

Plug the three-prong 220V ACpower cord into a dedicated outlet(see Electrical Requirements).

16

Type 2Remove lockingclip to install orremove gas spring.

THREADED LOCKING RING

RECEPTACLEON BENCH

CANOPY TO BENCHPOWER CORD

The unit is shipped with aRemote Control Bypass Pluginstalled. Your sunbed willnot operate without eitherthe bypass plug or a remotesystem connected. If remoteoperation is desired, seeRemote Connections.

17

REMOTE PORTS

WIREDREMOTE

PORTS (RJ-22)

WIRELESSREMOTE

PORT (RJ-11)

SHORT BOLT

Turn bench over. Install hinge brackets to ends of bench suchthat the short boss engages the stud above the bolt hole, andthe long boss engages the hole below the bolt hole. Secureusing 5/16” x 1” Allen-head bolts and 5/16” metal washers.Tighten bolt snug, then an additional half turn.

8STUD

Place the bushingsinto hinge brackets.

9

Lift the canopy and hold itbetween the hinge brackets.

10

Insert 5/16” x 1 1/2” bolts with nylonwashers into both hinge brackets.Tighten bolts into the endcap threadedinserts until snug, then an additionalhalf turn. Do not overtighten to avoiddamaging threaded inserts.

11

Connect the canopy tobench power cord to thebench receptacle. Align theterminals and firmly pushon until seated then tightenthe threaded locking ring.

15

29237-01A - Page 3

Page 4 - 29237-01A

Scenario 2 - T-Max 3A with WirelessIn single sunbed installations, the T-Max® 1A and 3A can offer thesame control as the T-Max® Manager, eliminating the need for aManager. If you’re using a 1A in this manner, it must have a chiplabelled “master” installed on its circuit board. The remote controlbypass plug must not be used in this configuration. The 3A may beused as a “master” with no modification.

After you have set the T-Max® 1A’s, or 3A’s, address to “0” (refer to yourT-Max® user’s guide) and the sunbed’saddress to “1”, simply connectone G2 (with Power Injector) tothe T-Max® 3A and one G2 tothe tanning bed.

Scenario 4 - T-Max® Manager Series with Wireless combinationConnect one G2 (with Power Injector) to the Manager and one G2 toa wireless ready tanning bed. The rest of the salon may be “daisy-chained” together and connected to the wireless equipped tanningbed, eliminating the need to wire the Manager to the tanning beds.

Scenario 3 - T-Max® Manager Series with Wireless combination 2Wireless can be easily added to an existing salon already utilizing T-Max®. Connect one G2 (with Power Injector) to the Manager and oneG2 to each wireless ready tanning bed. Therest of the salon may be “daisy-chained”together and connected to the Manager.

Remote Connections

Your sunbed incorporates advanced circuitry allowing it to connectand communicate with most remote control systems. If a remote sys-tem is to be used, first determine whether the remote system is a T-Max® System or a standard remote system operating with a controlrelay. Follow the appropriate instructions for your system type.

T-Max® ProductsThe T-Max® remote systems offer the ultimate in sunbed control, whileallowing the tanner easy straightforward operation. Your sunbed is con-figured to directly connect to this system, including the wireless remotesystem. The circuitry inside your sunbed eliminates the need for the T-Max® 1A or 3A when connecting to the T-Max® Manager series. Yoursunbed supports the auto addressing feature of the latest T-Max®Manager models and the following parameters: 5, 6, 7, 8, 9, 10, 15 and23. See your T-Max® manual for descriptions of these parameters andhow they function.

T-Max® Wireless Remote System The T-Max® G2 eliminates wires in your salon, allowing easy setupwithout hiring an electrician to run wires. It also protects your invest-ment from damage by isolating each unit from one another. Yoursunbed arrives “wireless ready”, which means it connects directly tothe T-Max® wireless system. Older tanning beds, and T-Max® man-agers, also utilize this system but require a T-Max “Power Injector” (PI)to provide the needed power to the wireless unit.

Remote System Hook-up ScenariosFollow the diagrams below and on the next page to see the many dif-ferent scenarios for hooking up your salon. If you need further assis-tance, call T-Max® directly at (417) 338-5101.

The remote connection is not designed to supply or accept highvoltage, nor can it provide power to an external timer. Thesunbed’s remote interface circuitry operates on 5 volts, attemptingto connect it to any higher voltages will damage the sunbed aswell as void your warranty.

CAUTION

Scenario 1 - T-Max® Manager Series with Complete WirelessConnect one G2 (with Power Injector) to the Manager and one G2 toeach of the tanning beds. Install as many beds as you like with thisconfiguration. Units that do not communicate with T-Max will need aG2 with Power Injector and an additional 3A to operate. If you havean older T-Max® Manager that doesn’t support auto addressing, set theaddress of each sunbed manually as described in Setting the addressmanually. You can place your sunbed at any location in the series.

Go straight to the source with all your T-Max® brand remote questions: (417) 338-5101

Scenario 6 - Single Bed wired to T-Max® 3AIn single sunbed installations, the T-Max® 1A and 3A can offer thesame control as the T-Max® Manager, eliminating the need for aManager. If you’re using a 1A in this manner, it must have a chiplabelled “master” installed on its circuit board. The remote controlbypass plug must not be used in this configuration. The 3A may beused as a “master” with no modification.

After you have set the T-Max® 1A’s, or 3A’s, address to “0” (refer to yourT-Max® user’s guide) and the sunbed’s address to “1”, simply connectthe RJ-22 modular cables, describedin the T-Max® user’s guide, directlyinto either of the smaller ports locat-ed on the canopy and either port onthe back of the T-Max® 1A or 3A.

Scenario 7 - Non T-Max® Remote System wired to unitMost non-T-Max® remote systems control the sunbed by the use of arelay. The relay operates the sunbed by connecting and disconnect-ing a pair of wires leading from the sunbed. Refer to the user’s man-ual provided with your remote system to determine if it operates in thisway. To connect your sunbed tothis type of system a remoteinterface kit is required. Contactyour place of purchase to obtainthe kit. The illustration at rightdetails a typical connection.Follow the instructions providedwith the kit and from theremote’s manual to make thenecessary connections.

NOTE: A T-Max® 1A with a“master” chip can be substituted

for a 3A.

Scenario 5 - T-Max® Manager Series with wiresAs always, this tanning bed is fully compatible with a wired T-Max®system. Simply connect the RJ-22 modular cable(s), described in theT-Max® Manager manual, into the remote port(s) located on the backof the canopy and follow the instructions that came with your remotesystem.

Using Your Sunbed

Before using your sunbed, please note the following:

• Your skin should be free of cosmetics, tanning oils, or other bodylotions prior to tanning except for those specifically made for usewith tanning devices. However, do not remove natural body oils bybathing or showering immediately before tanning.

• Keep treated hair from contacting sunbed surfaces. Many hair prod-ucts can damage the sunbed acrylic. Wear a shower cap or towel ifyou use gels, mousses, sprays, or other hair products.

• Your sunbed is designed for individual use. Always wear the safetygoggles supplied with your sunbed or another approved pair of gog-gles, as defined under 21 CFR 1040.20. Regular sunglasses do notprovide adequate protection from ultraviolet light.

Exposure TimesFollow the guidelines for skin type and exposure times as shown in thetable below. Untanned persons should not tan on consecutive daysduring their first week of tanning. Never tan more than once a day.Tanning normally appears after the first few sessions and maximizesafter approximately four weeks. Tan once or twice per week thereafterto maintain appearance. Persons already having a base tan may beginat advanced levels corresponding to the extent of their base tan.

Skin Type:I Sensitive Skin (Burns easily and severely and does not tan.)II Light Skin (Burns easily and severely and tans minimally.)III Normal Skin (Burns moderately and tans average.)IV Dark Skin (Burns minimally, tans easily and above average.)

Setting the address manuallyBefore connecting your sunbed to the T-Max® Manager or T-Max® 1Aor 3A, the address of your sunbed must first be set. Set the address man-ually as described below.

Setting the Address 1. Make sure the sunbed display is showing “0”.2. Press the red stop button and, without releasing it, press the

green timer button and hold both for three seconds. The displayshould indicate an address number from “1” to “255”.

3. If you are using a T-Max® 1A or 3A as a “master” remote, theaddress of the sunbed must be set to “1”. If you are using a T-Max® Manager each sunbed must be assigned a differentaddress. To adjust the address, press the green timer button tocount up until the desired number (from 1 to 128) is achieved.Addresses 252 to 255 are not normally used.

4. Press the red stop button to return to the normal display mode.

1-99

100-128(blinking dot)

252-255(blinking dot)

RECOMMENDED EXPOSURE TIMES IN MINUTESLevel 1/Week 1 Level 2 Level 3 Level 4 Level 5

Skin Type: 1st-3rd SessionsI Sensitive NOT RECOMMENDED FOR TANNINGII Light 2 4 6 8 11III Normal 3 5 8 11 11IV Dark 4 6 9 11 11

MAXIMUM EXPOSURE TIME IS 11 MINUTES

29237-01A - Page 5

Care and Maintenance

Cleaning After Use

Clean and disinfect your tanning bed’s bench and canopy after eachuse. Use a non-abrasive disinfectant cleaner that does not containammonia or ammonia derivatives. Ammonia may damage the acrylicshield. Spray the acrylic lightly with disinfectant and wipe dry with aclean soft cloth.

Thorough Periodic Cleaning

The cooling fans draw air through the bed and will cause a dustbuildup on the lamps and reflectors. When a dust buildup is observed,it is necessary to thoroughly clean the inside of the bench and canopy.

1 Remove the acrylic shields and lamps.2 With a soft cloth, wipe the entire length of each lamp.3 Clean both sides of the acrylic shields with a non-ammonia dis-

infectant cleaner.4 Wipe the reflectors with a clean damp cloth.5 Re-install the lamps and acrylic shields.

Mechanical Inspection

Inspect the unit’s mechanical integrity every 400-500 hours of use. Thetimer has a built-in circuit to help keep track of time based mainte-nance tasks. See the Hour Counter section on the next page.

• Inspect the unit’s fasteners verifying that all are firmly in place.Pay particular attention to the hinge bolts.

• Inspect gas springs for signs of wear. Replace gas springs that willnot hold the canopy in the full open position when raised.

• Inspect the AC power cord and its connections.• Inspect the acrylic. Replace if broken, cracked or badly scratched.

Removing/Replacing Acrylic ShieldsThe acrylic shields are secured in place by hinged profiles which runthe length of the bed, both front and back. Simply pry up on the insideedge of the profile until it releases its latching action (see figurebelow). Continue to pry up the profile across its entire length until itswings back freely. Repeat for the other profile. The long edges of theacrylic shield are now exposed. Standing in front of the sunbed, graspthe long exposed edge of the acrylic and carefully slide it toward youuntil it is removed.

After changing the lamps, replacethe acrylic shields by reversingthe above directions. Closethe hinged profile by pushingit back into place until itsnaps tight.

Page 6 - 29237-01A

PROFILE

CAUTIONBe careful. The edges of theacrylic shield may be sharp.

Start pulling from themiddle of the profile!

A Timer display - Displays remaining time.

B Timer button - Turns bed on. Timer dis-play shows remaining time. If a lessertime is desired, press timer buttonuntil desired time is displayed.

C Stop button - Interrupts tanning session.

D Face tanner button - (Units equipped with facial units only.) Turnsface tanner, or turbo lamps, on and off.

Operation

A

B C

(When connected to the T-Max® Manager or T-Max® 1A or 3A.)

1 If the remote system has been set to allow a pre-tanning delay time,the timer display (A) will repeatedly flash the delay symbol “dL” andthen the remaining delay time. Press the timer button (B) or wait untilthe delay time has expired to begin the tanning session. The lampswill turn on and the timer will begin to count down.

2 Lift the canopy, lie down on the bench (face up), lower the canopyas close to your body as possible, with no less than 2” between thecanopy acrylic and your body.

3 When the timer reaches “0” the lamps turn off. If you want to stopyour session before time expires, press the stop button (C).

4 Raise the canopy by using the outer edge of the canopy, do notpush up on the acrylic shield as it may crack. The cooling fans runfor three minutes after the lamps shut off to aid in cooling thesunbed. The timer will indicate “..” as a reminder to clean thesunbed. After the sunbed is cleaned press the timer button and thedisplay will return to “0”.

(When used without remote or when connected to a remote systemusing a control relay)

1 Press the timer button (B) to begin the tanning session. The timer dis-play (A) displays the remaining time. The lamps will turn on and thetimer will begin to count down from the maximum tanning sessiontime. If a tanning time less than the displayed time is desired repeat-edly press the timer button (B) to decrease the remaining time.

2 Lift the canopy, lie down on the bench (face up), lower the canopyas close to your body as possible, with no less than 2” between thecanopy acrylic and your body.

3 When the timer reaches “0” the lamps turn off. If you want to stopyour session before time expires, press the stop button (C).

4 Raise the canopy by using the outer edge of the canopy, do notpush up on the acrylic shield as it may crack. The cooling fans runfor three minutes after the lamps shut off to aid in cooling thesunbed.

D

Removing/Replacing Lamps

To be assured of maximum tanning effectiveness, change lamps afterapproximately 800-1000 hours of use. Tanning will continue after thistime but at a slower rate. To ensure trouble-free operation of yoursunbed, replace the lamp starters whenever the lamps are replaced. Werecommend using the lamps specified below. Use of uncertified lampsis a violation of Federal regulations and will void your warranty.1 Grasp a lamp at one end and at the middle, then turn the lamp a

quarter turn. The lamp may then be gently removed from its holder.2 To reinstall lamp, insert pins on the ends of the lamp into the slots

on top of the lamp holder and turn the lamp a quarter turn.

Removing/Replacing Face Tanner Lamps

After removing the canopy acrylic shield, replace the face tanner lampas follows:

Step 1 Support the face tan-ner assembly withyour hand whileunscrewing the tworetaining screws. Theface tanner glass cas-ing will swing down-ward.

Step 2 The lamp can now be exchanged. The lamp holders areequipped with spring contacts which enable the lamp to beremoved easily. Remove the old lamp and discard. Install thenew lamp, using a clean cloth or paper towel. Ensure that thelamp is firmly seated in the lamp holders.

Note! Never take hold of the lamp such that your fingers are in con-tact with the lamp glass. Finger oils will greatly reduce the lamp’soperational life.

Step 3 Gently close the face tanner glass casing and lock itclosed with the screws. Ensure that the screws firmlysecure the glass casing.

DANGER

Unfiltered light from face tanner can cause severe burns.Never turn sunbed on while face tanner is disassembled orwhen glass filters are removed. Immediately discontinue use of this equipment if face tannerglass is broken or any unfiltered light can be seen escapingface tanner assembly.

RETAININGSCREWS

Problem TroubleshootingSolution

Sunbed not tanning1. Clean sunbed, see Thorough Periodic Cleaning.2. Ensure supply voltage is between 208 and 230V AC.3. Replace lamps if lamp hours are greater than 800hrs.4. Replace acrylic.

Lamps fail to light and timer display is blank1. Make sure the unit is connected to a power source.2. Check source of AC power. Reset circuit breaker or replace

fuse.

Timer display changes to indicate a tanning time after the timer but-ton is pressed but lamps do not come on

1. Bypass plug is not installed, see Electrical Connections.2. A bypass plug other than the one sent with your tanning bed

has been used.3. If remote is being used, other than T-Max® Manager, the

external timer may not be activated.4. Remote wiring is incorrect, see the instructions provided

with the remote interface kit.

Timer display continues to show a 0 after the timer button is pressed1. T-Max® Manager remote system has not yet been set. 2. Sunbed address is not set correctly, see Remote

Connections.

One or more lamps fail to light1. Check that lamp is installed correctly.2. Switch unlit lamp with a lamp that lights, if new lamp lights

and old lamp still does not, replace old lamp.

The canopy will not stay upNOTE: Gas springs are manufactured to hold the canopy in its

fully open position as well as allow it to rest fully closed. Ifleft open for an extended period of time some creep downmay occur. This is considered normal. Keep the unit closedwhen not in use. If the canopy will not stay fully open whenraised...

1. Raise and lower the canopy a few times to lubricate gasspring internal seals.

2. Replace gas springs.

Hour Counter

This sunbed incorporates an ingenious hour counter function into thetiming circuitry. It allows the operator of the unit to monitor the hoursof use of the lamps, making it easy to determine when to change them.You may also decide to use this function to monitor other time basedmaintenance tasks.

To determine how many hours the unit has been in service (since thelast reset of the hour counter memory), first make sure the timer dis-play shows “0”. Then simply hold the stop button for three seconds.The display will show two pairs of numbers which indicate the num-ber of hours of service, then return to “0”. (example: Display shows 08then 54. This equals 854 hours.) NOTE: If the unit is connected to a T-Max® remote device, it may briefly lose communication with theremote. This is normal.

To erase the indicated hours, disconnect power from the sunbed. Pressand hold the green timer button as you reconnect power. Release thebutton after a few seconds.

29237-01A - Page 7

Page 8 - 29237-01A

Problem Troubleshooting (continued)Solution

My bed won’t work with the T-Max® Manager remote system1. The sunbed must first be set to a unique address, see

Remote Connections.2. The bypass plug may be installed in the series in an inap-

propriate location. Remove bypass plugs when using T-Max® products.

When auto-addressing the first bed does not register an addressWhen using the auto address feature of the T-Max®Manager you must wait 10 seconds from the time you startthe auto address function before addressing the first bed.

I forgot what address I set my sunbed toBy pressing the stop button and then the timer button, andholding both for 3 seconds, the timer display will show thesunbed’s address number. Press the stop button to exitaddress mode.

My bed is connected to the T-Max® Manager remote system andwhen the delay time has expired the timer display starts countingdown but the bed lights do not come on

The auto start feature of the remote system is disabled, seethe instructions provided with your remote system.

My bed, connected to a T-Max® Manager, did not display “dL” butdoes indicate:

“0”1. Remote device has not been set.2. The sunbed has not been connected to the remote system,

see Remote Connections.a tanning time and the lamps have come on

1. Delay time of T-Max® Manager has not been set.2. Delay time has expired and session has begun.

a tanning time but the lamps have not come onAuto start function of T-Max® Manager has been turned off.Press the timer button to turn on lamps.

If you did not find the solution to your problem, contact your placeof purchase for additional assistance

Proudly manufactured in the U.S.A.

Record this information for ease of service:

Date of purchase:

Bench serial number:

Canopy serial number:

Perfect Sun® 18 MONTH WARRANTY

Perfect Sun® warrants your tanning unit to be free of structural defects in material and work-

manship, under normal use, for its lifetime. Perfect Sun® will, at its discretion, repair any

structural defect which materially affects the performance of the tanning unit, or replace the

tanning unit.

For eighteen (18) months following the shipping date of your tanning unit, Perfect Sun® will

provide replacements for parts that prove to be defective in material or workmanship.

Fluorescent lamps, and lamp starters are warranted against manufacturer’s defects for a period

of ninety (90) days following the shipping date of your tanning unit. Acrylics will be warrant-

ed against manufacturer’s defects for a period of 1 year (prorated).

Labor costs associated with repair or replacement work covered by this warranty will be

reimbursed for repair or replacement work required to be performed for a period of six (6)

months following the shipping date of your tanning unit. All such warranty service must be

performed by an authorized Perfect Sun® service person. All labor charges must be author-

ized by Perfect Sun® prior to the start of repairs and must not exceed the established rates

and time allotment policies established by Perfect Sun®. If your tanning unit must be

returned for service, all freight charges shall be at your expense.

Normal wear and tear, damage from misuse or abuse, damage incurred in transit or damages

resulting from unauthorized repairs or modifications are not covered by this warranty.

Warranty coverage does not include cosmetic abnormalities such as scratches, nicks, dents, or

other cosmetic changes that do not materially interfere with the function of the tanning unit.

THIS STANDARD 18 MONTH WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,

WHICH ARE HEREBY DISCLAIMED. No one has the authority to change or modify this

Standard 18 Month Warranty in any respect. To obtain service under this Standard 18 Month

Warranty, contact Perfect Sun® at 1-800-361-5170 or visit www.PerfectSunTanning.com

to fill out an online warranty request form.

IN NO EVENT SHALL YOUR DISTRIBUTOR OR THE MANUFACTURER BE LIABLE

AT LAW OR IN EQUITY FOR ANY LOSS, LIABILITY, DAMAGE OR EXPENSE IN AN

AMOUNT IN EXCESS OF THE PURCHASE PRICE RECEIVED, OR FOR LOSS OF USE

OR PROFITS, LOSS OF TIME, INCONVENIENCE, RENTAL OR SUBSTITUTE PROD-

UCTS, LOSS OF BUSINESS, LOSS OF INCOME, OR ANY OTHER INCIDENTAL,

INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the

exclusion or limitation of incidental or consequential damages, and the above limitation or

exclusion will not apply to residents of some states. This Standard 18 Month Warranty gives

you specific, legal rights and you may have other rights which may vary from state to state.

Contact Perfect Sun® for the authorized Service Center nearest you. This warranty is serial

number specific and only applies to tanning units purchased through an authorized Perfect

Sun® Dealer. This warranty is extended to the individual or legal entity whose name appears

on the original sales document and may not be transferred to any other individual or legal

entity. This warranty is void if the tanning unit is modified in any manner from its original

design.

To file a Warranty Claim, please follow these steps:

1. Locate the silver serial number label, located on the back ofthe unit near the power cord on the canopy. Identify the serialnumber and model number of the unit.

2. Proof of purchase must be provided before any claim will beconsidered.

3. Contact Perfect Sun® at 1-800-361-5170 or visitwww.PerfectSunTanning.com to fill out an online warrantyform.

4. If it is determined that a defective part needs to be replaced,Perfect Sun® will arrange for the pick-up or shipment of thereplacement part.

Unpacking and Inspection

While unpacking your tanning bed inspect all items and make surethey are free from any visible damage. Report the extent of any dam-age to the transportation company.