Upload
colin-horton
View
216
Download
2
Tags:
Embed Size (px)
Citation preview
29 Oct 07
1
COMPACT HIGH POWERLASER DAZZLER™
(CHPLD)
INITIALTRAINING PRESENTATION
29 Oct 07
2
TOPICS
• Introduction 3-7• Warnings/Safety 8-9• Specifications 10• Nomenclature 11• Battery Replacement 12• On-Off Push Button 13• Intermittent Button Switch 13• Remote Switch Tail Module 14• Make Safe When Not In Use 15• Delrin Fixture 16• Diffuser 17• Cleaning 18-19• Tips 20• Questions 21
29 Oct 07
3
CHP LASER DAZZLER™
A Portable, Non-Lethal, Eye-Safe, Multi-Purpose Device Effective Both Day and Night
29 Oct 07
4
CHP LASER DAZZLER™
It is the most rugged/powerful/compact laser device available that is suitable for this purpose
The CHPLD engages the target in a wall of green laser (532nm) light, which disorients and distracts the subject
This is accomplished by overloading the optic nerve rendering the subject nearly sightless for a short period of time – there is no doubt the individual will see the CHPLD, even in bright sunlight at 200 meters
29 Oct 07
5
CHP LASER DAZZLER™
Specifically designed for applications where gaining the instant attention of individuals in varying light conditions including clear, bright sunny days is critical
IDEAL FOR CONVOY AND ENTRY CONTROL OPERATIONS
Immediate recognition by approaching vehicles or pedestrians which avoids the use of lethal force due to confusion or unseen /unrecognized hand signals
29 Oct 07
6
CHPLD at 100 yards – bright daylight
Drivers approaching a convoy or checkpoint may not see hand signals or realize they are entering a restricted/danger
zone
They cannot fail to see the CHPLD even if distracted by traffic, sunlight, pedestrians, or other activities
29 Oct 07
7
OTHER USES Mark your position and identify friendly units at long distances
Distraction & disruption of hostile groups
Counter sniper
Block line of sight when approaching target
Counter surveillance
Front view showing 4 lasersMounted on Tripod
29 Oct 07
8
WARNINGS/SAFETY
• Laser Dazzlers™ are non-lethal devices, HOWEVER, with the potential for permanent eye damage if used improperly the CHPLD should always be TREATED LIKE A LOADED WEAPON
• DO NOT point this device at any person unless it is operationally required
• The user is solely responsible for the safe operation of the CHPLD and for adhering to the instructions and warnings provided
• DO NOT look at the CHPLD thru optical devices such as binoculars or telescopes
• This device has sufficient energy densities to cause irreversible eye damage and or permanent blindness if used on a subject at close distances or reflected onto a subject’s eyes from a highly reflective surface
29 Oct 07
9
WARNINGS/SAFETY
• DO NOT use on subjects at distances closer than 20 meters or reflect back on subjects at distances equivalent to 20 meters or closer without the holographic diffuser installed
• DO NOT use on subjects at distances closer than 3 meters or reflect back on subjects at distances equivalent to 3 meters or closer with the with the holographic diffuser installed
• The CHPLD is powered by lithium sulfur dioxide primary batteries and are therefore NOT RECHARGEABLE
• DO NOT attempt to charge the battery pack. Any attempt to do so is dangerous
29 Oct 07
10
• 500 Milliwatt, 532nm (green) flashing laser• Overall length - 11 inches• Maximum diameter - 2.5 inches• Powered by lithium sulfur dioxide primary batteries• BATTERIES ARE NOT RECHARGABLE• Safe Ranges
– Minimum eye safe range – 20 meters (Without holographic diffuser)– Minimum eye safe range – 3 meters (With holographic diffuser)
• Maximum effective range:– 200 meters – bright sunlight– 2 kilometers – night
• Construction: – Anodized aluminum– Weight – 2.0 lbs.– Weight as shown – 2.6 lbs.– All parts produced in the USA
• Operating Conditions: – All-weather, general purpose and water tight
SPECIFICATIONS
29 Oct 07
11
NOMENCLATURE
CHPLD
DELRIN FIXTURE
Aiming Device
29 Oct 07
12
BATTERY REPLACEMENT
• Unscrew tail module• Install battery positive end first• Rotate battery for best fit when installing• Check to confirm O-Ring (3) is still in
place• DO NOT over tighten switch module
29 Oct 07
13
ON-OFF PUSH BUTTON
• Operate laser by push and release of intermittent button switch
INTERMITTENT BUTTON SWITCH
• Push and release to turn on
• Push and release again to turn off
29 Oct 07
14
REMOTE SWITCH TAIL MODULE
• The laser can be operated for 45 minutes continuously from the initial charge
• When the laser is turned off the capacitor is fully charged• The cable connectors for this module are male/female pin type• Mate each connector• Secure by gently rotating the locking collar until it engages the
mating part• Rotate clockwise approximately 1/8 of a turn to lock in place
• This module contains an electronic switch circuit powered by a capacitor which is charged by the battery pack when the laser is OFF
• INITIAL CHARGE REQUIRES 4 MINUTES
29 Oct 07
15
MAKE SAFE WHEN NOT IN USE
• Integral On-Off Push Button Switch Module– Unscrew ¼ to ½ turn
– Press button to ensure laser does not fire
– If necessary unscrew additional ¼ turn increments until laser will not fire
• Remote Switch Tail Module– Disconnect cable connectors
– DO NOT unscrew module since the capacitor charge may dissipate and the initial charge time (4 minutes) would be required to operate the laser
– Press button switch to ensure laser does not fire
• Long Period of Non-use– Remove battery pack
– Reinstall Tail Switch Module to prevent dirt and moisture from entering the device
29 Oct 07
16
DELRIN FIXTURE
• The laser is provided in the Delrin Fixture and sighted to the red dot reticule scope.
• An intermittent on/off button is built into the fixture and is armed by connecting the cable on the Tail Module to the mating connector on the Delrin Fixture
• Secure by gently rotating the locking collar until it engages the mating part
• Rotate clockwise approximately 1/8 of a turn to lock in place
29 Oct 07
17
DIFFUSER
Adding the provided Holographic Diffuser reduces the minimum eye safety distance from 20 meters to only 3 meters
• Unscrew window module
• Remove white washer
• Place diffuser on window
• Reinstall white nylon washer
• Reinstall module on device
29 Oct 07
18
CLEANING
Remove the laser from the Delrin Fixture
• Disconnect cable
• Remove the Tail Module
• Loosen the 6-32 set screws
• Slide the laser forward
• Make sure not to lose the O-Ring (3)
• It is not necessary to remove the set screws
• To reinstall just reverse the process
29 Oct 07
19
CLEANING
Window• With device front facing down unscrew window module
• Remove white nylon washer
• Turn module over and clean surface underneath
• The window & O-Ring will drop out
• Clean window with appropriate cleaner such as Windex® sprayed onto a cloth
• Reinstall in reverse order
• Make sure O-Ring (1) is in the groove
• Make sure O-Ring (2) is still on the laser body
CHPLD
• Wipe with damp cloth and or a cleaner such as Windex® sprayed onto the cloth
• DO NOT immerse in water or cleaning fluids
NO OTHER FIELD DISASSEMBLY OF THE LASER OTHER THAN AS DESCRIBED ABOVE IS PERMITTED. DOING SO WILL DAMAGE THE DEVICE AND VOID THE WARRANTY
29 Oct 07
20
TIPS
• TIPS FOR EFFECTIVE USE– Individuals or groups: Aim at the center of the chest then raise the
beam to eye level for a very short period of time – repeat as necessary
– Vehicles: Aim at the center of the windshield then move to the drivers side for a very short period of time – repeat as necessary
29 Oct 07
21
Easily seen at 1 mile in bright sunlight
QUESTIONS ?