0

2.500

6.000

14.750

.150

7.048

12.864

0 2.64

2

5.13

0

0

.750

7.75

0

8.62

29.

247

8.25

0

.154

8.16

1

8.39

7

.463

.229

.229

.463

A

A

B B

X2

.75

X3

.75

X1

.75

16.129

0

8.000

01.25

0

Z1

.75

AREA FOR MARKINGS

0

1.250

0

1.250

0

.625

2.00

0

7.25

0

9.24

7

8.62

2

Y2

.75

Y1

.75

0.1

20.2

30.9

20

0

1.000

6.000

14.750

0 .120

TO

DA

TUM

S X1

,X2,

AN

D X

3

1.25

0

SECTION A-A

Y1&Y2

.75

X1

.75

X2

.75

X3

.75

0.120.420

2.620

1.038

3.6804.105

0

1.250

D

SECTION B-B

Z1

.75

.120

.167

.230

.234

DETAIL D SCALE 2 : 1

NOTES UNLESS OTHERWISE SPECIFIED :DRAWING PREPARED IN ACCORDANCE WITH ASME Y14.8M-19961.THE FINAL PART MUST NOT CONTAIN MATERIALS IN EXCESS OF UANTITIES AS SPECIFIED BY 2.THERMO FISHER SCIENTIFIC S ENVIRONMENTAL COMPLIANCE SPECIFICATION 267-1858XX.

TOLERANCESALL UNTOLERANCED DIMENSIONS ARE BASIC.3.ALL UNTOLERANCED SURFACES ARE .060 X Y Z4.CORNERS SHOWN SHARP TO .125 MAXIMUM BREAK5.FILLETS SHOWN SHARP .125 MAXIMUM6.

GEOMETRYRE UIRED MARKINGS ON PART ARE PART NUMBER, COUNTRY OF ORIGIN, DATE AND 7.FOUNDRY SYMBOL NAME LOCATED WHERE MARKEDTHIS DRAWING SHALL BE USED WITH 3D CAD MODEL FOR GEOMETRY DEFINITION8.WALL THICKNESS: .313 NOMINAL &.250 MINIMUM REF.9.FLOOR THICKNESS: .300 NOMINAL WITH EXTERNAL WEB AT .37510.DRAFT: 3 DEGREE NOMINAL &5 DEGREE MAXIMUM REF.11.ESTIMATED VOLUME 173.50 IN 312.ADDITIONS RIBS TO BE APPROVED BY PROCURING ENGINEER13.GATE, RISER, VENT, PARTING LINE, AND E ECTOR PIN LOCATIONS SHALL BE APPROVED BY 14.PROCURING ENGINEER BEFORE TOOL CONSTRUCTION

CASTING DEFECTSPARTING LINE EDGES, FLASH, GATES, RUNNER AND RISER EXTENSIONS .020 MAXIMUM15.SURFACE TEXTURE AND POROSITY MUST MEET THE FOLLOWING AFTER MACHINING PER 056-16.7626XX DRAWING:

NO PORE SHALL BREAK THROUGH TO A SECONDARY SURFACE.1.NO PORE CAN BE LARGER THAN .015 ON A .250 HOLE SURFACE, ON A .750 2.RAISED SURFACE, OR ON THE RAISED SEAL LIP AROUND THE PART.NO CONCENTRATION OF FOUR OR MORE DEFECTS IN ANY 1.00 REGION3.NO CONCENTRATION OF TEN OR MORE DEFECTS IN ANY 5.00 REGION4.

SURFACE TEXTURE PER ASME B46.1-2002 TO BE 150

17.

00B

REV DESCRIPTION ECO # APPD. BY APPD. DATE CREATED BYE05 ADDED .060 X .060 RELIEF AROUND TOP OUTSIDE EDGE. ADDED .425 INCHS

TO FEET BOSSES. R. Bach 01-10-2012 R. Bach00A RELEASE TO PRODUCTION, NO CHANGES 500000045587 M. McGaren 02-13-2012 M. McGaren00B CHANGED MACHINE DWG NUMBER REF IN NOTES, ADDED SURFACE

TEXTURE NOTE TO 150 MICROINCH 500000047239 M. McGaren 05-08-2012 W. Keefe

A

B

2345678

12345678

D

C

B

C

D

A

1

EXPORT NOTICE: THE COMMODITIES OR TECHNOLOGY DEPICTED OR DISCUSSED IN THIS DRAWING WERE EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT ADMINISTRATION REGULATIONS. DIVERSION CONTRARY TO U.S. LAWS IS PROHIBITED

5225 VERONA RD MADISON, WI 53711-4495

PART/ASSY FILE: 271-7207

THIS DOCUMENT CONTAINS CONFIDENTIAL OR PROPRIETARY INFORMATION OF THERMO FISHER SCIENTIFIC CORP. NEITHER THIS DOCUMENT NOR THE INFORMATION HEREIN IS TO BE REPRODUCED, DISTRIBUTED, USED OR DISCLOSED, EITHER IN PART OR IN WHOLE, EXCEPT AS SPECIFICALLY AUTHORIZED BY US.

DO NOT SCALE DRAWING

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES.

SHEET 1 OF 1SCALE: 1:2

DRAWING SIZE:DATEDATE

DATE

TITLE

PART NUMBER REVISION

DPROJECT ENGMFG ENG

CHECKEDDATEDRAWNFINISHMATERIAL

UNLESS OTHERWISE SPECIFIEDSURFACE FINISH IS:

63

SEE NOTESALUMINUM ALLOY 356.0-T51

RAW MATL IS50 NIR BASE CASTING

271-720700B ECCN: EAR99ECCN EXCEPTION:

02-13-2012B. WEBER R. BACH02-13-2012

01-10-201207-11-2011M. Jablonski J. CLEARY

Thermo Fisher Scientific

DIMENSION AND TOL. PER ASME Y14.5-2009 SCREW THREADS PER MIL STD-9 ABBREVIATIONS PER MIL STD-12 WELDING SYMBOLS PER AWS A2.0UNLESS OTHERWISE SPECIFIED REMOVE ALLBURRS AND BREAK SHARP EDGES .005" TO .015" FACE WIDTH

19.05

Φ19.05

25.4

19.05

152.4

374.65

3.048

5.842

23.368

Φ19.0531.753

.048

19.05

31.75 31.75

Φ19.05

Φ19.05

Φ19.05

Φ19.05

テキスト

テキスト

テキストテキスト

テキストテキスト

テキスト

テキストテキストテキスト

15.875

50.8

67.107

130.3

184.15

219

234.874

テキスト

テキストテキストテキストテキストテキスト

テキスト

テキストテキストテキスト

テキスト

テキスト

テキストテキスト