Parker Hannifin CorporationMotion & Control Training Dept.6035 Parkland Blvd., Cleveland, OH 44124-4141Phone: 216.896.2495mctrain@parker.com

2018 North America Course ScheduleHydraulic Technology • Pneumatic Technology

Mobile Hydraulic Technology

* In addition to fees charged by IFPS.

Fluid Power Society Hydraulic Specialist

Hydraulic Systems Engineering - 3 week class - 3 consecutive months

Hydraulic Maintenance Technology

Industrial Hydraulic Technology

Mobile Hydraulic Technology

Mobile Troubleshooting using Schematics

AMH

Acronym

2018 Class OfferingsDaysTuition FeeClass Title

Advanced Mobile Hydraulics $1,495 3½

HMT

HSE

IHT

Electrohydraulic Feedback Systems

Introduction to Electrohydraulics

EFS

EHD

FPS HS

FPS PS

HCS Hydraulic Component Sizing

Fluid Power Society Pneumatic Specialist

$1,500 3½

3½

$1,200

$1,500

$895 *

$895 *

$1,500

4½

4½

3½

3½

4½

3½

$1,700 / Week

$1,200

3½

3½

PTI

MHT

MTS

Pneumatic Technology for Industry $1,200

$1,200

$1,495

3

Industrial Hydraulic Class Descriptions

Hydraulic Maintenance TechnologyA 3½-day course which covers basic theory and methods for maintaining and troubleshooting hydraulic components and circuits. The student will receive actual hands-on experience with such things as pump setup procedures, circuit assembly and troubleshooting and graphic symbology reading.

Hydraulic Systems EngineeringThe only training course in the world that focuses exclusively on the design problem that is faced by the HYD System Engineer. In a combination of laboratory and lecture, you will learn how to proceed from system concept to meet accuracy, speed and force requirements. This course has been specifically organized to serve the needs of the HYD System Engineer who must design industrial machinery that operates faster, more smoothly, more reliably, without shocks and vibrations, and must reduce production costs while making products that are better.

Fluid Power Society - Hydraulic Specialist Review Class & ExamThis review and test encompasses 28 hours of review for the Hydraulic Specialist certification followed by a 3-hour written test. The review consists of going through the material/knowledge required for the certification (including any necessary math) as well as taking sample written tests. The course is taught by an IFPS Accredited Instructor.

Hydraulic Component SizingAn in-depth study of hydraulic components, their performance and how available performance data should be interpreted to evaluate circuits for effectiveness, cost savings and energy conservation. In addition, students will learn to recognize and overcome problem areas related to individual component characteristics which can affect the total operation of a system.

EHD

FPS HS

HCS

Electrohydraulic Feedback SystemsThis class concentrates on how to design a predictable, stable, electrohydraulic positioning system to meet speed, force, duty cycle and accuracy requirements. Approximately 25% of the class time is spent in our lab connecting, operating and tuning a closed loop electrohydraulic system.

EFS

Industrial Hydraulic TechnologyA 3½-day course which covers basic components of an industrial hydraulic system. Class sessions are reinforced with lab exercises.

HMT

HSE

IHT

Introduction to ElectrohydraulicsA 3½-day course whereby students are introduced to the rapidly developing field of electrohydraulic proportional control. The course concentrates on how electronics are used to control hydraulic components. A typical circuit board is analyzed and explained. 25% of the time is spent in the lab working with electrohydraulic proportional valves.

Troubleshooting Mobile Hydraulic SystemsTroubleshooting methodology is provided using the hydraulic circuit to group and isolate the potential problems when symptoms such as improper speed, pressure, heat, noise, leaks and specific failures have been identified. This course begins with a brief review of fundamental fluid principles and hydraulic schematic symbols. It then covers reasons for components and hydraulic accessories.

MTS

Mobile Hydraulic Class Descriptions

Advance Mobile HydraulicsThis component and control level course will incorporate component symbols learned in MHT into complete schematics. Remote control of pressure valves using pilot valves, bleed off orifices and proportional controls will be discussed. Simultaneous control of multiple actuators while maintaining pressure and flow requirements will be reviewed. Operation and setup of load sense pumps will be demonstrated. Slip-in and cartridge valve design and operation will be presented. Proportional directional control valve function and use will be introduced. Closed loop hydrostatics systems, power steering and power beyond functions will also be covered.

AMH

MHT

Mobile Hydraulic TechnologyThis course is designed to introduce participants to the fundamentals of mobile hydraulic components and how to maintain and diagnose components within a system. Participants will also apply these fundamentals through the use of actual circuit assembly.

Pneumatic Class Descriptions

Fluid Power Society - Pneumatic Specialist Review Class & ExamThis review and test encompasses 28 hours of review for the Pneumatic Specialist certification followed by a 3-hour written test. The review consists of going through the material/knowledge required for the certification (including any necessary math) as well as taking sample written tests. The course is taught by an IFPS Accredited Instructor.

FPS PS

PTIPneumatic Technology for IndustryA 3-day course designed to introduce participants to pneumatics as it relates to industrial machinery. In addition, students will learn how and why pneumatic components work and how to maintain pneumatic systems.

Class January February March April May June July August September October November December

IHT 20-23 Ely 1-4 Mil 11-14 Cal 4-7 Ely

HMT 6-9 Ely 9-12 Ely

HCS 17-20 Ely 13-16 EGV

EHD 15-18 Ely

EFS 19-22 Ely

HSE 17-21 Ely 15-19 Ely 12-16 Ely

FPS - HS 27-31 HQ

MHT 14-17 EGV 18-21 Mil 27-30 Ely

MTS 25-28 EGV

AMH 23-26 EGV

PTI 3-5 Ely 23-25 Mil 6-8 Ely

FPS - PS 12-16 HQ

IndustrialHydraulic

MobileHydraulic

Pneumatic

2018 Class Schedule

Calgary, AB, Canada (Cal)Cleveland, OH (HQ)Elk Grove Village, IL (EGV)Elyria, OH (Ely)Milton, ON, Canada (Mil)

Cal

Class Locations

EGV

Parker Hannifin Canada3141B 16th St., NECalgary, AB Canada

Parker Hannifin Canada160 Chisholm DriveMilton, ON Canada L9T 3G9

Ely

HQ

Mil

Parker Hannifin Corporation850 Arthur AvenueElk Grove Village, IL 60007

Parker Hannifin CorporationHydraulic Valve Division520 Ternes AvenueElyria, OH 44035

Parker Hannifin Corporation6035 Parkland Blvd.Cleveland, OH 44124

Canada

U.S.

PreetJones@parker.commctrain@parker.com

To register, email your registration form to:

CVV code:

Name on credit card:Billing address for card:

Credit card number:

Expiration date:

I would like to attend:

Class Acronym Date Location Registration Fee

Credit card (fill in information below)

Department Number (Parker employees only)

Special Need:

Registration Form

Motion & Control Training Dept.6035 Parkland Blvd., Cleveland, OH 44124-4141

Please note: Cancellations received less than ten (10) working days in advance of the class date, or student no-shows, will be charged with 100% cancellation fee per student.

Name: (Enter as you would like it to appear on your certificate)

Company:

Address:

Parker Hannifin Corporation

Phone: Cell:

E-mail:

Method of payment: