MS. CLAIRE CHOU CASWELL INC 8TH FL 242 BO-AI ST SHU-LIN DISTRICT Date: 2011/05/11 NEW TAIPEI Subscriber: 100514234 238 TAIWAN PartySite: 1802571 File No: E326741 Project No: 11CA21330 PD No: 11O18912 Type: R PO Number: U141438 Subject: Procedure And/Or Report Material The following material resulting from the investigation under the above numbers is enclosed. Issue Date Vol Sec Pages Revised Date 2010/08/11 X1 A16 Revised Proc/Rpt Section If there are illegible images in this package,legible images may be found online via MyHome@UL under My UL Reports/CDA Please file revised pages and illustrations in place of material of like identity. New material should be filed in its proper numerical order. NOTE: Follow-Up Service Procedure revisions DO NOT include Cover Pages, Test Records and Conclusion Pages. Report revisions DO NOT include Authorization Pages, Indices, Section General Pages and Appendixes. Please review this material and report any inaccuracies to (886-2-2896-7790) This material is provided on behalf of Underwriters Laboratories Inc.(UL) or any authorized licensee of UL. TPI File

Issue Date: 2010-08-11 Page 1 of 7 Report Reference # E326741-A16-UL 2011-05-10

Copyright © 2011

UL TEST REPORT AND PROCEDURE Standard: UL 60950-1, 2nd Edition, 2007-03-27 (Information Technology

Equipment - Safety - Part 1: General Requirements) CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03 (Information Technology Equipment - Safety - Part 1: General Requirements)

Certification Type: Listing CCN: NWGQ, NWGQ7 (Information Technology Equipment Including

Electrical Business Equipment)

Product: Communication Appliance Model: CAD-0208-XXXX-XXX (X can be 0-9, A-Z, a-z, the dash sign "-" or

blank) Rating: 15 Vdc / 4 A or 12 Vdc / 3.33 A (optionally provided on the marking

plate)

Applicant Name and Address: CASWELL INC 8TH FL 242 BO-AI ST SHU-LIN DISTRICT NEW TAIPEI 238 TAIWAN

This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the above referenced Standards. The products have been found to comply with the requirements covering the category and the products are judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on such products which comply with this Test Report and any other applicable requirements of Underwriters Laboratories Inc. ('UL') in accordance with the Follow-Up Service Agreement. Only those products which properly bear the UL Mark are considered as being covered by UL's Follow-Up Service under the indicated Test Procedure. The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety. Any information and documentation involving UL Mark services are provided on behalf of Underwriters Laboratories Inc. (UL) or any authorized licensee of UL.

Prepared by: Nathan Chen

Underwriters Laboratories Inc.

Reviewed by: Jason Chiu

Underwriters Laboratories Inc.

Issue Date: 2010-08-11 Page 2 of 7 Report Reference # E326741-A16-UL 2011-05-10

Supporting Documentation The following documents located at the beginning of this Procedure supplement the requirements of this Test Report: A. Authorization - The Authorization page may include additional Factory Identification Code markings. B. Generic Inspection Instructions - i. Part AC details important information which may be applicable to products covered by this Procedure.

Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of this Test Report.

ii. Part AE details any requirements which may be applicable to all products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of each Test Report.

iii. Part AF details the requirements for the UL Certification Mark which is not controlled by the technical standard used to investigate these products. Products are permitted to bear only the Certification Mark(s) corresponding to the countries for which it is certified, as indicated in each Test Report.

Product Description A Class III networking device, supplied by UL certified power adapter with LPS output. Consists of hard disk drive, system fan, RTC battery and other electronic components mounted on PWB, and then enclosed with metal enclosure.

Model Differences N/A

Technical Considerations Equipment mobility : Movable.

Connection to the mains : No direct connection.

Operating condition : Continuous.

Access location : Operator accessible.

Over voltage category (OVC) : N/A.

Mains supply tolerance (%) or absolute mains supply values : No direct connection.

Tested for IT power systems : No.

IT testing, phase-phase voltage (V) : N/A.

Class of equipment : Class III (supplied by SELV).

Considered current rating (A) : 20.

Issue Date: 2010-08-11 Page 3 of 7 Report Reference # E326741-A16-UL 2011-05-10

Pollution degree (PD) : PD 2.

IP protection class : IP X0.

Altitude of operation (m) : Up to 2000.

Altitude of test laboratory (m) : Up to 2000.

Mass of equipment (kg) : 1.39.

The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted  by  the  manufacturer’s  specification  of:  40  degree  C.  

The following circuit locations (with circuit/schematic designation) were investigated as a limited power source (LPS): All output connectors (USB ports and RJ45 ports).

The following are available from the Applicant upon request: Installation (Safety) Instructions / Manual.

Based upon product specification provided by the manufacturer, this equipment is intended to be supplied by an UL certified power adapter suitable for use at a Tma of 40 degree C.

Additional Information N/A Markings and instructions Clause Title Marking or Instruction Details Inter-connecting cables - External detachable

Listee's Name and Part number (Marking or Instruction)

Power rating - Company identification

Listee's or Recognized company's name, Trade Name, Trademark or File Number

Power rating - Model

Model Number

Replaceable batteries "CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions."

Telecom type connectors not used for telecommunication purposes

For telecommunication type connectors and terminals not used for connection to the telecommunication network should be provided with a marking identifying the specific function or circuit characteristic the connector or terminal is

Issue Date: 2010-08-11 Page 4 of 7 Report Reference # E326741-A16-UL 2011-05-10

used for.

Special Instructions to UL Representative N/A Production-Line Testing Requirements Electric Strength Test Special Constructions - Refer to Generic Inspection Instructions, Part AC for further information.

Model Component Removable

Parts Test probe location V

rms V dc Test Time,

s -- -- -- -- -- -- --

Earthing Continuity Test Exemptions - This test is not required for the following models: All models

Electric Strength Test Exemptions - This test is not required for the following models: All models

Electric Strength Test Component Exemptions - The following solid-state components may disconnected from the remainder of the circuitry during the performance of this test: --

Sample and Test Specifics for Follow-Up Tests at UL

Model Component Material Test Sample(s) Test

Specifics -- -- -- -- -- --

Issue Date: 2010-08-11 Page 5 of 7 Report Reference # E326741-A16-UL 2011-05-10

TABLE: List of Critical Components

Object/part or Description

Manufacturer/ trademark

type/model technical data CCN Marks of Conformity

01. Label -- -- Minimum 45 degree C. PGDQ2 or PGJI2 UL 02. Power Adapter -- -- Output: 12 Vdc, minimum 3.33 A. LPS. QQGQ UL 02a. Power Adapter (Alternate)

-- -- Output: 15 Vdc, minimum 4 A. LPS. QQGQ UL

03. Enclosure -- -- Plated steel. Overall 300 by 145 by 44 mm. Minimum 1.9 mm thick. See Enclosure 4-01 for openings.

-- --

04. Hard Disk Drive (Optional)

-- -- Generic. 5 Vdc, maximum 0.7 A. NWGQ2 UL

05. System Fan (Optional)

Sunonwealth Electric Machine Industry Co., Ltd.

KDE1204PFV1 12 Vdc, 0.09 A. Minimum 8.0 CFM. GPWV2 UL

06. RTC Battery (BAT1) -- CR2032 3 Vdc. Maximum abnormal charging current 10 mA. The protection of reverse changing provided by blocking diode D12 and 1 kohm resistor R55.

BBCV2 UL

07.Polyswitch (FS1) -- -- 8 Vdc, Ih 1.6 A, It 2.8 A. CA = 3. XGPU2 UL 08. PWB -- -- Minimum V-1, minimum 105 degree C. ZPMV2 UL 09. Internal Wiring, Secondary ELV/SELV

-- -- FEP, PTFE, PVC, TFE, neoprene, polyimide or marked VW-1. Minimum 30 V. Minimum 60 degree C.

AVLV2 UL

10. Connector and Receptacle, Secondary ELV/SELV

-- DC jack, USB, RJ45

Copper alloy pins housed in bodies of plastic rated V-2 minimum.

QMFZ2 UL

10a. Connector and Receptacle, Secondary ELV/SELV (Alternate)

-- DC jack, USB, RJ45

Minimum 30 V. ECBT2, RTRT2 UL

11. Interconnecting Cable, Secondary ELV/SELV (Optional)

-- -- Maximum length 3.05 m. Marked VW-1 or FT-1. AVLV2 UL

11a. Interconnecting Cable (Optional) (Alternate)

-- -- Maximum length 3.05 m. Type CMP, CMR, CMG, CM, CMX, CMUC or CMH.

DUZX UL

11b. Interconnecting Cable (Optional)

-- -- Maximum length 3.05 m. Type CMP, CMR, CMG, CM, CMX, CMUC or CMH.

DUXR UL

Issue Date: 2010-08-11 Page 6 of 7 Report Reference # E326741-A16-UL 2011-05-10

Object/part or Description

Manufacturer/ trademark

type/model technical data CCN Marks of Conformity

(Alternate)

Issue Date: 2010-08-11 Page 7 of 7 Report Reference # E326741-A16-UL 2011-05-10

Enclosures

Type Supplement Id Description Photographs 3-01 Top-front view Photographs 3-02 Bottom-rear view Photographs 3-03 Inner view

Diagrams 4-01 Enclosure openings Schematics + PWB

Manuals 6-01 Wall-mount instructions Miscellaneous

File E326741 Vol. X1 Sec. A16 PHO-01 Issued: 2010-08-11

File E326741 Vol. X1 Sec. A16 PHO-02 Issued: 2010-08-11

File E326741 Vol. X1 Sec. A16 PHO-03 Issued: 2010-08-11

File E326741 Vol. X1 Sec. A16 DIA-01 Issued: 2010-08-11

File E326741 Vol. X1 Sec. A16 MAN-01(Page 1)Issued: 2010-08-11

File E326741 Vol. X1 Sec. A16 MAN-01(Page 2)Issued: 2010-08-11

Issue Date: 2010-08-11 Page 1 of 2 Report Reference # E326741-A16-UL Revision Date: 2011-05-10 Test Record

Test Record No. 1

The manufacturer submitted representative production sample of Communication Appliance, model CAD-0208-XXXX-XXX (X can be 0-9, A-Z, a-z, the dash sign "-" or blank). Only limited tests were conducted on model CAD-0208-XXXX-XXX (X can be 0-9, A-Z, a-z, the dash sign "-" or blank) because identical main board is employed in a previously certified model CAD-0205-XXXX-XXX (X can be 0-9, A-Z, a-z or blank). See Report E326741-A10, dated 2010-04-23. All tests were conducted by Sporton International Inc. located in Junghe, Taipei, Taiwan, under the TPTDP program.

The following tests were conducted: Test Testing Location/Comments Input: Single-Phase (1.6.2) Steady Force (4.2.1 - 4.2.4) Impact (4.2.5, 4.2.1, Part 22 10.2) Loading - Wall and Ceiling Mounted Equipment (4.2.10) Heating (4.5.1, 1.4.12, 1.4.13) Abnormal Operation (5.3.1 - 5.3.9) Test results are valid only for the tested equipment. These tests are considered representative of the products covered by this Test Report. The test methods and results of the above tests have been reviewed and found to be in accordance with the requirements in the Standard(s) referenced at the beginning of this Test Report.

The following tests were waived: Test Rationale for Waiving Limited Power Source Measurements (2.5) Identical main board evaluated under

E326741-A10 Lithium Battery Reverse Current Measurement (4.3.8) Identical main board evaluated under

E326741-A10 Overload of Operator Accessible Connector (5.3.7) Identical main board evaluated under

E326741-A10

The following supplements are provided as a part of this Test Record. NOTE: These supplements are only available to the Applicant via the CDA system.

Type Supplement Id Description Attachment 2-01 Construction review datasheet Datasheet 2-02 Test datasheet

Issue Date: 2010-08-11 Page 2 of 2 Report Reference # E326741-A16-UL Revision Date: 2011-05-10 Test Record

Test Record No. 2

No test is deemed necessary due to correcting the technical data of interconnecting cable.