Upload
leody-f-diaz-jr
View
7
Download
2
Embed Size (px)
Citation preview
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2007 American Honda Motor Co., Inc. – All Rights Re
AII 37473
BODY SIDE MOLDINGserved AII 37473 (0708
2008 CR-V
) 0
Issue Date
AUG 2007
PARTS LISTLeft front side protector
Right front side protector
Left rear side protector
Right rear side protector
4 Alcohol pads
TOOLS AND SUPPLIES REQUIRED
Masking tapeRulerIsopropyl alcoholShop towel
INSTALLATION • Be careful not to damage the body paint finish.• This body side molding kit should be installed only if the
ambient air temperature is above 60°F (15°C).• To allow the adhesive to cure, do not wash the vehicle
for 24 hours.• These instructions show the left body side molding
being installed; the same procedure applies to installing the right body side molding.
Installing the Body Side Molding1. Measure and mark the left front door, and attach
masking tape to the areas shown.
6517030Y
MASKING TAPELEFT FRONT DOOR
MOLDINGMASKING TAPE
MOLDING
MASKING TAPE
900 mm
83 mm
88 mm
30 mm
4.5 mm
door lower trim.
1 of 38P05-SWA-1000-91
2. Peel back 1-1/2–2 inches of the adhesive backings, and tape them to the front of the body side molding. Remove the front adhesive backing.
3. Using one alcohol pad, clean the door where the left front upper molding will attach.
4. Position the left front molding on the left front door, aligning it with the masking tape you attached in step 1.
6517040Y
MASKING TAPE
ADHESIVE BACKING(Remove.)
4 ADHESIVE BACKINGS (Peel back 1-1/2–2 inches of the adhesive backing, and tape them to the front of the body side molding.)
LEFT FRONT BODY SIDE MOLDING
ADHESIVE BACKING (Remove.)
6517090Y
MASKING TAPE
LEFT FRONT DOOR
MASKING TAPE
LEFT FRONT SIDE PROTECTOR
2 of 3 AII 37473
5. Press on the left front body side molding firmly with the palm of your hand while removing the adhesive backings. Remove about 50 to 100 mm at a time, pressing on the molding with the palm of your hand.
6. Remove the masking tape.
Installing the Rear Body Side Molding7. Measure and mark the left rear door, and attach
masking tape in the areas shown.
6517050Y
LEFT FRONT DOOR
LEFT FRONT BODY SIDE MOLDING
4 ADHESIVE BACKINGS
LEFT FRONT BODY SIDE MOLDING
ADHESIVE BACKING
6517060Y
LEFT REAR DOOR
MASKING TAPE
MASKING TAPE
MOLDING
4.5 mm
88 mm
30 mm
91 mm
300 mm
Top edge of door lower trim.
(0708) © 2007 American Honda Motor Co., Inc. – All Rights Reserved
8. Peel back 1-1/2–2 inches of the adhesive backings, and tape them to the front of the rear body side molding. Remove the front and rear adhesive backings.
9. Using one alcohol pad, clean the door where the left rear molding will attach.
10. Position the left rear body side molding on the left rear door, aligning it with the masking tape you attached in step 7.
6517072Y
ADHESIVE BACKING(Remove.)
ADHESIVE BACKING(Remove.)
MASKING TAPE
LEFT REAR BODY SIDE MOLDING
4 ADHESIVE BACKINGS (Peel back 1-1/2–2 inches of the adhesive backing, and tape them to the front of the body side molding.)
6517100Y
MASKING TAPE
LEFT REAR BODY SIDE MOLDING
LEFT REAR DOOR
MASKING TAPE
© 2007 American Honda Motor Co., Inc. – All Rights Reserved AII 37473
11. Press on the left rear body side molding firmly with the palm of your hand while removing the adhesive backings. Remove about 50 to 100 mm at a time, pressing on the molding with the palm of your hand.
12. Remove the masking tape.13. Repeat steps 1 thru 12 to install the body side
molding on the right side of the vehicle.
6517080Y
LEFT REAR DOOR
LEFT REAR BODY SIDE MOLDING
ADHESIVE BACKING
LEFT REAR BODY SIDE MOLDING
ADHESIVE BACKINGS (4)
(0708) 3 of 3