2008-05-12_011655_Binder3

8/3/2019 2008-05-12_011655_Binder3

1/10

2.5L

1996 Chrysler Sebring JXi

1996 System Wiring Diagrams' 'Chrysler - Sebring Convertible1996 Chrysler Sebring JXi

1996 System Wiring Diagrams' 'Chrysler - Sebring Convertible

8/3/2019 2008-05-12_011655_Binder3

2/10

Fig. 14: 2.5L, Engine Performance Circuits (1 of 4)



8/3/2019 2008-05-12_011655_Binder3

3/10




8/3/2019 2008-05-12_011655_Binder3

4/10




8/3/2019 2008-05-12_011655_Binder3

5/10




8/3/2019 2008-05-12_011655_Binder3

6/10

8/3/2019 2008-05-12_011655_Binder3

7/10

Fig. 2: Identifying Ignition Switch Connector C219 TerminalsCourtesy of CHRYSLER CORP.


STEERING COLUMN SWITCHES - CONVERTIBLE' '1996 ACCESSORIES & EQUIPMENT Chrysler Corp. Steering

Column Switches

8/3/2019 2008-05-12_011655_Binder3

8/10

Fig. 3: Identifying Ignition Switch Connector C220 TerminalsCourtesy of CHRYSLER CORP.

IGNITION LOCK CYLINDER

Removal

Disconnect negative battery cable from auxiliary jumper terminal on left side strut tower. Remove uppersteering column shroud. Pull lower shroud down far enough to access lock cylinder retaining tab. Place lockcylinder in RUN position. Depress retaining tab and remove lock cylinder. See Fig. 7 .

Installation

1. Insert ignition key into lock cylinder. Turn key to RUN position (retaining tab can be depressed). Shaft atend of lock cylinder aligns with socket in end of housing. To align socket with lock cylinder, ensuresocket is in RUN position.

2. Align lock cylinder with grooves in housing. Slide lock cylinder into housing until tab sticks throughopening in housing. Turn ignition switch to OFF position. Remove key. Install steering column shrouds.Connect negative battery cable.



Column Switches

8/3/2019 2008-05-12_011655_Binder3

9/10

Fig. 7: Removing Ignition Lock CylinderCourtesy of CHRYSLER CORP.

IGNITION SWITCH

Removal

1. Disconnect battery negative cable from auxiliary jumper terminal on left side strut tower. Remove fuse

panel cover from left end of instrument panel. Remove screw holding end of instrument panel top cover.2. Pull center bezel off. Remove screws holding instrument panel top cover to center of instrument panel.

Pull instrument panel top cover up enough to gain access to knee bolster screws.

3. Remove lower knee bolster screws and knee bolster. Remove screws from lower steering column shroud.Pull lower shroud clear of ignition cylinder. Hold tilt wheel lever down, and slide lower shroud forwardto remove it from column.

4. Tilt wheel to full down position. Remove upper steering column shroud. Remove screws holdingcombination switch to lock housing. Place key in RUN position. Depress lock cylinder retaining tab andremove lock cylinder.



Column Switches

8/3/2019 2008-05-12_011655_Binder3

10/10

5. Disconnect ignition switch electrical connectors. Using a No. 10 Torx bit, remove ignition switchmounting screw. Pull ignition switch from steering column. See Fig. 8 .

Installation

Ensure ignition switch and actuator shaft are in RUN position. Carefully install ignition switch. Switch willsnap over the retaining tabs. To complete installation, reverse removal procedure.

Fig. 8: Removing Ignition SwitchCourtesy of CHRYSLER CORP.



Column Switches

Documents

2008-05-12_011655_Binder3