1

②

①

③

Service Parts:

RH

LH

J3110AN001J3110AN002

①, ③

②, ③

Part NameNo.

Rear Gate Trim RH (Right Hand)①

Rear Gate Trim LH (Le  Hand)②

Pa­ern Paper③

GG599-01110-A

J3110AN020Genuine Part Number:

OUTBACKApplicable Model:

2-piece Rear Gate Trim - ChromeInstallation Manual

2

Clean the area shown in the figure using a clean cloth and rubbing alcohol.1

50℃ (122℉)

35℃ (95℉) 35℃ (95℉)

15℃ (59℉)

A-A Cross-sec�onAlign on the end of corner R.

Alignment area

A

A

A

A

A

A

Align the Pa�ern Paper (RH) with the shape of the Rear Garnish and affix it with Masking Tape.2

Masking Tape Cloth Rubbing AlcoholProtec�ve Sheet

※Install this product before applying Vehicle Wax. If the vehicle already has the Wax applied, please remove the Wax on mounting area before installing this product.

3

Masking Tape

<Out side>

Release Film

Peel-offLeave 3.15 in

(80 mm) or more

Peel-off

★

Peel 5 of the Release Films on the back side of the Rear Gate Trim RH about 2 in (50 mm) in the direc�on shown in the figure and affix to the out side with Masking Tape. Peel-off the remaining 2 Release Films. Leave at least 3.15 in (80 mm) of the Release Films as shown with a star mark (★).

3

Make gap equal

Align corner

Align with the posi�oningline of the Pa�ern Paper (RH).

B

B

C

C

B-B Cross-sec�on (Reference)

C-C Cross-sec�on

0.098 in(2.5 mm)

While making the gap between the right side of the Rear Gate Trim RH and the end of the Rear Gate Garnish equal, align the �p with the posi�oning line of the Pa�ern Paper (RH).Align the shape of le� end of the Rear Gate Trim RH with the Rear Gate Garnish and press the whole of the product lightly.

4

Press

Press

❶❶

❷❷ Press

While keeping the posi�on of the Rear Gate Trim RH, peel-off the Release Films in the order as shown in the figure, and Press the product. Be careful not to let the exposed tape touch the paper template.

5

50℃ (122℉)

35℃ (95℉)

35℃ (95℉)

15℃ (59℉)

4

Remove

Remove the Pa�ern Paper (RH).7

24 Hours

Install the Rear Gate Trim LH with the same procedure as RH. Clean the vehicle. This now completes installa�on work.

8

❸❸

❹❹

❺❺Press

Press

Press here after peeling ❸ off.

Press Press

Press

Press Press

While keeping the posion of the Rear Gate Trim RH, peel-off the Release Films in the order as shown in the figure, and Press the product.And finally press the whole of the product with a pressure of 11 lbf (49 N) or greater. Be careful not to scratch the product when a�aching it.

6

50℃ (122℉)

35℃ (95℉)

35℃ (95℉)

15℃ (59℉)

RH

リヤゲートモールディング型紙

UP

RH

RH TAIL LAMP

0100mm

50mm

04in

2in

0 100mm50mm

0 4in2in

LHUP

LH

このキットに同梱されている型紙を使用してください。

ただし、コピーが必要な場合は、このページを印刷する前に、[実寸]を選択するか、[拡大縮小]を[100％]に設定するか、[印刷オプション]で

[拡大縮小しない]を選択してください。

印刷後、定規を使用して、印刷する縮尺が定規 と一致することを確認してから使用してください。

Rear Gate Molding Pattern Paper

2-piece Rear Gate Trim - Chrome Pattern Paper

Use the Rear Gate Molding Pattern Paper that’s provided in this kit.

However, if a copy is needed, select “Actual Size” or set Scale to “100%” or select “Do Not Scale” in the Print Options before printing this page.

After printing, use a ruler to confirm the printed scales match the ruler before using.

Scale

Scale

LH TAIL LAMP

GG500ｰ01060ｰA

TEMPLATE