Upload
techspaceofatul
View
218
Download
0
Embed Size (px)
Citation preview
8/13/2019 2 Noise Models
1/20
2. Noise Models
8/13/2019 2 Noise Models
2/20
www.electronics.dit.ie
Noise Models
In the above sections, the various physical sources ofnoise in electronic circuits were described.
In this section, these sources of noise are broughttogether to form the small-signal equivalent circuits: resistors (already discussed) diodes, bipolar (BJT) and
field-effect (FET) transistors and linear IC (OpAmp)
8/13/2019 2 Noise Models
3/20
www.electronics.dit.ie
Resistors
Noise can be modelled as a Thevenin equivalent voltage source or
a Norton equivalent current source.
The noise contributed by the resistor is modeled bythe source, thus the resistor is considered noiseless.
8/13/2019 2 Noise Models
4/20www.electronics.dit.ie
Two resistors
It is important to note that noise sources: Do not have polarity
Do not add algebraically, but as RMS sumsIf the sources are not correlated, then:
1121
21
2 44)( kTBRkTBRvvvrmsv nnnn +=+==
8/13/2019 2 Noise Models
5/20www.electronics.dit.ie
Correlated resistors
If the sources are correlated (derived from the same physical noise source), then there is an additional term:
C can vary between 1 and 1.
2121
21
2 2 nnnnn vCvvvv ++=
21
2
1
2
1
2
2)( nnnnnn vCvvvvrmsv ++==
8/13/2019 2 Noise Models
6/20www.electronics.dit.ie
Thermal Noise Power
The available noise power can be calculated from theRMS noise voltage or current:
That is, the available noise power from the source is independent of resistance proportional to temperature
proportional to bandwidth has no frequency dependence
P=4 x 10 -21 watts in a 1 Hz bandwidth at the standardnoise room temperature of 290 K.
( ) kTB R
E R E P
S
t
L
nono ===
22 2/
8/13/2019 2 Noise Models
7/20www.electronics.dit.ie
Can a resistor produceinfinite noise voltage?
therefore B RkT vv t n = 422
Equivalent circuit for noisy resistor always have some shunt. Therefore
Bvt when2
To find the noise power
22211
RC V V nono
+=
==0
22
C kT
dt V v nono
Therefore total noise power is independent of R !!!
8/13/2019 2 Noise Models
8/20www.electronics.dit.ie
Junction Diode
The equivalent circuit for a junction diodewas considered briefly in the considerationof shot noise.The basic equivalent circuit of diode
(discussed) can be made complete by addingseries resistance r s , as shown.
Br kT v st = 42
B f
I K BqI i d D
+= 22
Since r s , is a physical resistor due to theresistivity of the silicon, it exhibits thermalnoise.
Experimentally it has been found that any flicker noise presentcan be represented by a current generator in shunt with r d , andthis is conveniently combined with the shot -noise
8/13/2019 2 Noise Models
9/20www.electronics.dit.ie
BJT (noise model)
In a BJT in the forward-active region, minority carriersdiffuse and drift across the base region to be collected
at the collector-base junction.Minority carriers entering the collector-base depletionregion are accelerated by the field existing there andswept across this region to the collector.The time of arrival at the collector-base junction of the
diffusing (or drifting) carriers is a purely random process, and thus the transistor collector currentconsists of a series of random current pulses.
8/13/2019 2 Noise Models
10/20www.electronics.dit.ie
Contribution I
Consequently, collector current Ic shows full shotnoise , and this is represented by a shot noise current
generator ic2 from collector to emitter as shown in theequivalent circuit of BJT
BqI i C c = 22
8/13/2019 2 Noise Models
11/20
www.electronics.dit.ie
Contribution II
Base current I B in a transistor is due to recombination in the baseand to carrier injection from the base into the emitter.All of these are independent random processes, and thus I
Balso
shows full shot noise.Flicker noise and burst noise in a BJT have been foundexperimentally. This is represented by shot noise current
generator
( ) B
f f
I K B
f I
K BqI ic
cbb
Bb 2212
/12
+++=
8/13/2019 2 Noise Models
12/20
www.electronics.dit.ie
Contribution III
Transistor base resistor r b is a physical resistor andthus has thermal noise.
Collector series resistor r c also shows thermal noise, but since this is in series with the high-impedancecollector node, this noise is negligible and is usually
not included in the model.kTBvb 4
2 =
8/13/2019 2 Noise Models
13/20
www.electronics.dit.ie
All Contributions
Thermal noise in base resistor r b . kTBvb 42 =
Shot, Flicker noise and burst noise in Base current I B
Shot noise in collector current Ic , BqI i C c = 22
( ) B
f f
I K B
f I
K BqI ic
cbb
Bb 2212
/12
+++=
8/13/2019 2 Noise Models
14/20
www.electronics.dit.ie
corner frequency
The base-current noise spectrum can be plotted where burst noise has been neglected for simplicity.
The shot noise and flicker noise asymptotes meet at afrequency fa, which is called the flicker noise "corner"frequency. In some transistors using
careful processing, facan be as low as 100 Hz.In other transistors fa can
be as high as 10 MHz.
8/13/2019 2 Noise Models
15/20
www.electronics.dit.ie
FET noise model
In FET the resistive channel joining source and drain, so that thedrain current is controlled by the gate-source voltage.
Since the channel material is resistive, it exhibits thermal noise,and this is the major source of noise in FETs this noise sourcecan be represented by a noise-current generator i D 2 from drain tosource in the FET small-signal equivalent circuit.
8/13/2019 2 Noise Models
16/20
www.electronics.dit.ie
Contributions
Flicker noise in the FET is also found experimentally to berepresented by a drain-source current generator,
The other source of noise in FETs is shot noise generated by thegate leakage current and is usually very small . It becomes
significant only when the driving-source impedance connectedto the FET gate is very large. BqI i Gg = 2
2
B f I
K gkT i
a D
md 22
32
4 +
=
8/13/2019 2 Noise Models
17/20
www.electronics.dit.ie
BJT noise performance
Consider the noise performance of the simple transistor stagewith the ac schematic shown below
Consider the noise performance of the simple transistor stagewith the ac schematic shown below
8/13/2019 2 Noise Models
18/20
www.electronics.dit.ie
BJT noise performance (a)
In this equivalent circuit the external input signal vi, has beenignored so that output signal vo is due to noise generators only.C
is assumed small and is neglected. Output resistance r
o is also
neglected. The transistor noise generators are as described previously and in addition
The total output noise can be calculated by considering each
noise source in turn and performing the calculation as if eachnoise source were a sinusoid with rms value equal to that of thenoise source being considered.
BkTRv S s 42
= B RkT i Ll1
42
=
8/13/2019 2 Noise Models
19/20
www.electronics.dit.ie
( ) ( )[ ]
++
++++++=
C L
L
BbS bS S b
Lm
o
qI R
kT R
qI r Rr RkT Rr Z
Z
Rg B
v
24
24
2
2
2
2
222
BJT noise performance
The spectral density of the noise generator is equal:
Substituting for Z gives:
C j
r Z 1
=
( ) ( ) ( ) ( )[ ]
++
+++++++=
C L
L
BbS bS S b
Lmo
qI R
kT R
qI r Rr RkT f f Rr r
r Rg B
v
24
24/1
1
2
22
12
222
2
( )[ ] C Rr r f
S b +
=2
11
where Z is
where
8/13/2019 2 Noise Models
20/20
www.electronics.dit.ie
BJT noise spectral density
The output noise-voltage spectral density has a frequency-dependent part anda constant part.The frequency dependence arises because the gain of the stage begins to fall
above frequency f 1, and noise due to generators vs , vb , and ib ,which appearsamplified, also begins to fall.The constant term is due to noise generators il and icAssuming I
C=100 A, R
S=500 , R
L=5 k , =100, C
=10 pF, r
b=200