2 If you can install a Vista panel... you can install VistaKey!

2

If you can install a Vista panel...

If you can install a Vista panel...

you can install VistaKey!

you can install VistaKey!

3

VistaKeyVistaKey

Simple!

Just add it to the V-Plex polling loop for integrated access control

Simple!

Just add it to the V-Plex polling loop for integrated access control

4

VistaKey easily

the security of the system!

5

< Menu< Menu

1. Mapping VistaKey Zones to Panel

2. Initial System Test

3. Access Point Programming

4. Setting Up Access Groups

5. Adding, Editing & Deleting Cards

Getting VistaKey Up & RunningGetting VistaKey Up & Running

6

POWER SUPPLY MODULE

To Vistakey Module

To Transformer

Reader Interface

8

Main Terminal Interface

9

Mapping VistaKey Zones to Panel

Mapping VistaKey Zones to Panel

10

< Menu < Menu < Sub Menu < Sub Menu

Mapping Zones to Panel


Go into the program mode of the VISTA control. Go into the program mode of the VISTA control. Next go into Menu Mode by entering #93. The Next go into Menu Mode by entering #93. The keypad displays:keypad displays:

ZONE PROG?1 = YES 0 = NO

Press 1 for Confirm. The keypad displays:Press 1 for Confirm. The keypad displays:

Press 1 for zone programming. The keypad displays:Press 1 for zone programming. The keypad displays:

Set to Confirm?1 = YES 0 = NO

ENTER ZONE NO.?000 = QUIT

11

Enter a 3-digit zone number for the access point. Enter a 3-digit zone number for the access point. Start access control at zone 100. Press [ R ] on the Start access control at zone 100. Press [ R ] on the keypad twice. The keypad displays:keypad twice. The keypad displays:

100 ZONE RESPONSE



100 INPUT TYPE

Enter a 2-digit response type such as 01(Entry/Exit). Enter a 2-digit response type such as 01(Entry/Exit). Press [ * ] to accept the entry. Press [ * ] repeatedly Press [ * ] to accept the entry. Press [ * ] repeatedly until the keypad displays:until the keypad displays:

100 Access Point(01-15)

Enter 11 (DSM) and then press [ * ] to accept the Enter 11 (DSM) and then press [ * ] to accept the entry. The keypad displays:entry. The keypad displays:

12

< Menu< Menu

Enter a 2 digit access point number corresponding Enter a 2 digit access point number corresponding to the number selected on the VistaKey module’s to the number selected on the VistaKey module’s thumbwheel. Make the first one 01 and the second thumbwheel. Make the first one 01 and the second 02. Press [ * ] to accept the entry. Press [ * ] 02. Press [ * ] to accept the entry. Press [ * ] repeatedly until the keypad displays:repeatedly until the keypad displays:

Now enter a 3-digit zone number to program the Now enter a 3-digit zone number to program the Backup Door Status Monitor for this first Access Backup Door Status Monitor for this first Access Point (ex. 101). Press [ * ] on the keypad twice until Point (ex. 101). Press [ * ] on the keypad twice until the keypad displays:the keypad displays:



ENTER ZONE NO.?000 = QUIT101 ZONE RESPONSE

13

< Menu< Menu

Enter a 2 digit response type such as 01 (entry/exit). Enter a 2 digit response type such as 01 (entry/exit). Press [ * ] to accept the entry. Press [ * ] repeatedly Press [ * ] to accept the entry. Press [ * ] repeatedly until the keypad displays:until the keypad displays:

Enter the input device type 06 (serial number polling Enter the input device type 06 (serial number polling loop device). The backup DSM (VistaKey DSMB) is loop device). The backup DSM (VistaKey DSMB) is programmed as a polling loop device. The system programmed as a polling loop device. The system advances to the Smart Contact prompt or “V-Plex advances to the Smart Contact prompt or “V-Plex Relay” prompt.Relay” prompt.



101 INPUT TYPE

14

< Menu< Menu

Press [ 0 ] and then press [ * ] to continue. The keypad Press [ 0 ] and then press [ * ] to continue. The keypad displays: displays:

Note: this prompt is not displayed on some alarm Note: this prompt is not displayed on some alarm systems.systems.

Press [ 0 ] and then press [ * ] to continue. The Press [ 0 ] and then press [ * ] to continue. The keypad displays:keypad displays:

Enter the 2 digit (01-15) door # for VistaKey. Press [ * ] Enter the 2 digit (01-15) door # for VistaKey. Press [ * ] to continue. The keypad displays:to continue. The keypad displays:



101 SMART CONTACT1= YES 0= NO101 V-PLEX RELAY1= YES 0= NO

101 ACCESS POINT1= YES 0= NO

Note: the response to this Note: the response to this question must be the address question must be the address that was set in the VistaKey that was set in the VistaKey module for the door (access module for the door (access point) being programmed.point) being programmed.

15

< Menu< Menu

To enroll the VistaKey (DSMB) serial number:To enroll the VistaKey (DSMB) serial number:• Remove power from the VistaKey moduleRemove power from the VistaKey module• Activate the DSM Zone (open the door ) until the keypad Activate the DSM Zone (open the door ) until the keypad

beeps twice and the VistaKey serial number is beeps twice and the VistaKey serial number is displayeddisplayed

• Remove the fault from the DSM Zone (close the door) Remove the fault from the DSM Zone (close the door) and re-apply power to the Vista Keyand re-apply power to the Vista Key

Note: To enroll the VistaKey Note: To enroll the VistaKey DSMB zone, assign it to loop DSMB zone, assign it to loop 1. Loop 2 must be unused. 1. Loop 2 must be unused. Press [*] to continue.Press [*] to continue.



101 INPUT S/N : LA xxx xxxx : 1

16

< Menu< Menu

ENTER ZONE NO.?000 = QUIT

Press [ * ] repeatedly until the keypad displays:Press [ * ] repeatedly until the keypad displays:

Follow this same procedure for Access Point two (2) Follow this same procedure for Access Point two (2) for zones 102 and 103. Enter 000 and then press [ * ] to for zones 102 and 103. Enter 000 and then press [ * ] to accept the entry. The keypad displays:accept the entry. The keypad displays:

Press 1 to quit the menu mode and then enter #99 to Press 1 to quit the menu mode and then enter #99 to exit programming.exit programming.



QUIT MENU MODE?1 = YES 0 = NO 0

17

Initial Systems

Test

Initial Systems

TestThis operation of the VistaKey is This operation of the VistaKey is to check that the installed to check that the installed hardware is functional before hardware is functional before programming Access Points, programming Access Points, Groups and CardsGroups and Cards

18

< Menu< Menu

ACS TEST MODE0 = quit 0

ACS TEST MODEGRANT ALL CARDS 2

GRANT ALL CARDSACS TEST MODE

Using any of the alarm control panel keypads, enter Using any of the alarm control panel keypads, enter Installer Code # + 78. The keypad displays:Installer Code # + 78. The keypad displays:

Press 2 on the keypad. The keypad displays:Press 2 on the keypad. The keypad displays:

Press [ * ] on the keypad. The keypad displays:Press [ * ] on the keypad. The keypad displays:

Initial System TestInitial System Test

19

< Menu< Menu

Swipe any ADEMCO proximity card past the card reader. Swipe any ADEMCO proximity card past the card reader. If the unit is properly installed, the mag lock or door If the unit is properly installed, the mag lock or door strike activates, and the green LED temporarily strike activates, and the green LED temporarily illuminates on the card reader. If the test is successful, illuminates on the card reader. If the test is successful, advance to step 5. If the mag lock or door strike does not advance to step 5. If the mag lock or door strike does not activate, and the green LED does not illuminate, do the activate, and the green LED does not illuminate, do the following:following:


20

Check all wiring to the units and that external power Check all wiring to the units and that external power is applied. Return to Step 1 and repeat the test.is applied. Return to Step 1 and repeat the test.

Exit the ACS TEST MODE by entering Installer Code + Exit the ACS TEST MODE by entering Installer Code + # + 78 + 0 + *. The keypad stops beeping and # + 78 + 0 + *. The keypad stops beeping and displays:displays:


****DISARMED****READY TO ARM

21

< Menu< Menu

***DISARMED***READY TO ARM

If additional VistaKeys have been installed for If additional VistaKeys have been installed for additional access points, repeat step 4 at the card additional access points, repeat step 4 at the card reader for each of the additional access points.reader for each of the additional access points.

Exit the ACS Test Mode by entering Installer Code + # Exit the ACS Test Mode by entering Installer Code + # + 78 + 0 + * at the keypad. The keypad stops beeping + 78 + 0 + * at the keypad. The keypad stops beeping and displays:and displays:


22

< Menu< Menu

ENTER 0= RECENT1=COMPLETE DUMPSCAN LOG BY PART0=NO 1-8=PART #ALARM EVENT LOGTYPE CCC UUU

Use the following procedure to verify that all access Use the following procedure to verify that all access points tested actually processed through the points tested actually processed through the VistaKey and into the alarm control panel.VistaKey and into the alarm control panel.

Using any of the alarm panel keypads, enter Installer Using any of the alarm panel keypads, enter Installer Code + # + 60 to view the alarm panel control log. Code + # + 60 to view the alarm panel control log. The keypad displays:The keypad displays:




23

< Menu< Menu

ALL EVENT LOGTYPE CCC UUU

Press 3 repeatedly until the keypad displays:Press 3 repeatedly until the keypad displays:

Press 8. The keypad display shows the most recent Press 8. The keypad display shows the most recent event in the log. event in the log.

Press 1 to step back through the event log to verify Press 1 to step back through the event log to verify that all access points tested are in the log. The first that all access points tested are in the log. The first line of the log provides a partition number, date, & line of the log provides a partition number, date, & time. The second line shows “ACS GRT” or “EGR time. The second line shows “ACS GRT” or “EGR GRT” followed by a 3-digit zone number and user GRT” followed by a 3-digit zone number and user number of U999. number of U999.


Note that U999 indicates a card Note that U999 indicates a card not linked to a user. If the card not linked to a user. If the card was linked to a user, the user was linked to a user, the user number would be displayed.number would be displayed.

24

< Menu< Menu

If an access point shows up incorrectly (e.g., you If an access point shows up incorrectly (e.g., you tested access points (VistaKey addresses) 1 and 2 tested access points (VistaKey addresses) 1 and 2 but the log shows the zone for access point 1 twice), but the log shows the zone for access point 1 twice), check the address switch setting in the VistaKey for check the address switch setting in the VistaKey for the access point that is missing. the access point that is missing.

If an access point test is missing entirely, recheck If an access point test is missing entirely, recheck the system wiring.the system wiring.


25

Press [ * ] on the keypad to exit the Log View Mode. Press [ * ] on the keypad to exit the Log View Mode. The quick installation is complete and the access The quick installation is complete and the access point(s) are ready to be programmed into the alarm point(s) are ready to be programmed into the alarm control panel.control panel.

26

Access Point

Programming

Access Point

ProgrammingAccess point options for the VistaKey module(s) are set using Access Point Programming. To reach Access Point Programming, enter #93 Menu Mode Programming and press the [0] key until the display shows Access Point Programming

27

< Menu< Menu

Access Point Pgm1 = YES 0 = NOENTER ACS PT#01-15 00 = Quit 01

Enter #93 Menu Mode Programming and press the 0 Enter #93 Menu Mode Programming and press the 0 key until the following prompt is displayed:key until the following prompt is displayed:

Press 1 to select access prompt programmingPress 1 to select access prompt programming

Enter a number from 01 to 15 for the access point Enter a number from 01 to 15 for the access point number to be programmed or 00 to Quit Access Point number to be programmed or 00 to Quit Access Point ProgrammingProgramming

Access Point ProgrammingAccess Point

Programming

28

< Menu< Menu

01 DSM CONFIGNORM OPEN 0

Enter 1 digit for the DSM zone (VistaKey zone A) Enter 1 digit for the DSM zone (VistaKey zone A) configuration. The configuration entered must be the configuration. The configuration entered must be the DSM status when the door (access point) is closed. DSM status when the door (access point) is closed. Acceptable 1-digit entries are as follows. Acceptable 1-digit entries are as follows. Press [Press [] to ] to accept the entry.accept the entry.

0 = normally open0 = normally open 1 = normally closed 1 = normally closed 2 = EOLR normally open2 = EOLR normally open 3 = EOLR normally closed3 = EOLR normally closed


Programming

29

01 DOOR OPN TIME4s 3

The door open time is the amount of time that the door-The door open time is the amount of time that the door-locking device is kept in the unlocked (open) status locking device is kept in the unlocked (open) status following a valid card swipe at the card reader or RTE (if following a valid card swipe at the card reader or RTE (if enabled), unless a relatch condition occurs. Enter 1 digit enabled), unless a relatch condition occurs. Enter 1 digit (0 to 7) for the door strike relay duration in seconds.(0 to 7) for the door strike relay duration in seconds.0 = 1 second0 = 1 second 1 = 2 seconds 1 = 2 seconds 2 = 3 seconds2 = 3 seconds3 = 4 seconds 3 = 4 seconds 4 = 5 seconds4 = 5 seconds 5 = 10 second5 = 10 second6 = 15 seconds6 = 15 seconds 7 = 30 seconds7 = 30 seconds


Programming

30

< Menu< Menu

Enter 1 digit for door alarm timeout value. Timer for alarm Enter 1 digit for door alarm timeout value. Timer for alarm timeout starts at end of door open time defined previously; timeout starts at end of door open time defined previously; therefore, the total amount of time before zone fault is therefore, the total amount of time before zone fault is issued is the amount set for door open time plus amount issued is the amount set for door open time plus amount of time entered for this prompt. If access point is still open of time entered for this prompt. If access point is still open when timeout value entered has expired, a zone fault when timeout value entered has expired, a zone fault (alarm timeout) is reported to the VISTA panel and a Door (alarm timeout) is reported to the VISTA panel and a Door Propped event is logged. Press [Propped event is logged. Press [] to accept the entry.] to accept the entry.0 = 5 sec.0 = 5 sec. 1 = 10 sec. 1 = 10 sec. 2 = 15 sec. 2 = 15 sec. 3 = 30 sec. 3 = 30 sec. 4 = 1 min.4 = 1 min. 5 = 2 min.5 = 2 min. 6 = 5 min.6 = 5 min. 7 = 10 min.7 = 10 min.

01 ALARM TIMEOUT10S 0


Programming

31

< Menu< Menu

01 PREALARM TIME5S 0


Programming

The pre-alarm time is used to warn a person holding The pre-alarm time is used to warn a person holding the access door open that a zone fault will occur if the the access door open that a zone fault will occur if the door is not closed before the alarm timeout expires.door is not closed before the alarm timeout expires.

If the Alarm Timeout is set for 10 seconds and the pre-If the Alarm Timeout is set for 10 seconds and the pre-alarm time is 5 seconds, the pre-alarm warning alarm time is 5 seconds, the pre-alarm warning commences 5 seconds before the alarm condition commences 5 seconds before the alarm condition (zone fault) is reported to the panel.(zone fault) is reported to the panel.

32


Programming

NOTE: the pre-alarm signal is output from the NOTE: the pre-alarm signal is output from the VistaKey on the Trigger output and if used, must be VistaKey on the Trigger output and if used, must be enabled when responding to the Pre-Alarm Trig enabled when responding to the Pre-Alarm Trig prompt later in this section.prompt later in this section.

0 = 5 sec.0 = 5 sec. 1 = 10 sec. 1 = 10 sec. 2 = 15 sec. 2 = 15 sec. 3 = 30 sec. 3 = 30 sec. 4 = 1 min.4 = 1 min. 5 = 2 min.5 = 2 min. 6 = 5 min.6 = 5 min. 7 = 10 min.7 = 10 min.

33

< Menu< Menu

01 RELATCH on timeout/closed 0

When a DSM zone is installed at the door, system can When a DSM zone is installed at the door, system can determine that door has closed before the amount of determine that door has closed before the amount of time that it was to remain unlatched. When “relatch on time that it was to remain unlatched. When “relatch on timeout/closed” option is selected, system automatically timeout/closed” option is selected, system automatically relatches door when it closes or at timeout, whichever relatches door when it closes or at timeout, whichever occurs first.occurs first.


Programming

34

When “relatch on open” is selected, door stining lock When “relatch on open” is selected, door stining lock will relatch as soon as door is opened. The xxx on open will relatch as soon as door is opened. The xxx on open “ is used as a power saving mode for door strikes.“ is used as a power saving mode for door strikes.

0 0 relatches on timeout or when the door closesrelatches on timeout or when the door closes(whichever occurs first)(whichever occurs first)

1 1 relatches on door openingrelatches on door opening

Press [*] to accept the entry.Press [*] to accept the entry.


Programming

01 RELATCH on timeout/closed 0

35

< Menu< Menu

01 RTE CONFIGNORM OPEN 0

Enter 1 digit for the uncommitted RTE zone (VistaKey Enter 1 digit for the uncommitted RTE zone (VistaKey zone B) configuration. The choice entered for this zone B) configuration. The choice entered for this selection must be the status of the RTE device (switch) selection must be the status of the RTE device (switch) when it is not active (in the ready state). Acceptable 1-when it is not active (in the ready state). Acceptable 1-digit entries are as follows:digit entries are as follows:0 = normally open0 = normally open 2 = EOLR normally open 2 = EOLR normally open

1 = normally closed 1 = normally closed 3 = EOLR normally closed3 = EOLR normally closed

Press [Press [] to accept the entry.] to accept the entry.


Programming

36

< Menu< Menu

This prompt is used to extend the time the door may This prompt is used to extend the time the door may remain open without an alarm when the door is remain open without an alarm when the door is already in an open condition. already in an open condition.

When enabled, each additional Request to Exit When enabled, each additional Request to Exit (RTE) restarts the alarm timeout. (RTE) restarts the alarm timeout.


Programming

37

This selection allows a line of people to exit without an This selection allows a line of people to exit without an alarm being issued because of the amount of time the alarm being issued because of the amount of time the door is open.door is open.

Press 1 if additional RTE’s are to restart alarm timeoutPress 1 if additional RTE’s are to restart alarm timeoutPress 0 if the additional RTE’s should not restart the Press 0 if the additional RTE’s should not restart the alarm timeoutalarm timeout


Programming

01 RTE RETRIGGERNOT ENABLED 0

38

< Menu< Menu

01 RTE ENABLED ? NOT ENABLED 0

This prompt is used to define if the RTE is to be This prompt is used to define if the RTE is to be enabled (committed/used for the access point) or enabled (committed/used for the access point) or not enabled. not enabled.


Programming

39

Enabling the RTE allows the VistaKey to request Enabling the RTE allows the VistaKey to request and/or grant an access via this zone input. and/or grant an access via this zone input.

Disabling the RTE causes this zone to be an Disabling the RTE causes this zone to be an uncommitted zone; i.e., the VistaKey will not be able uncommitted zone; i.e., the VistaKey will not be able to grant access via this zone.to grant access via this zone.

Press 1 to select if the RTE is to be enabled. Press 1 to select if the RTE is to be enabled.

Press 0 to disable the RTE.Press 0 to disable the RTE.


Programming

01 RTE ENABLED ? NOT ENABLED 0

40

< Menu< Menu

01 RTE DOORSTRIKEENABLED 1

This prompt is used to define whether the RTE (if This prompt is used to define whether the RTE (if enabled in the previous step) will unlock the enabled in the previous step) will unlock the doorstrike and start the exit timeouts (1) or just start doorstrike and start the exit timeouts (1) or just start the exit timeouts (0).the exit timeouts (0).

Press 1 to cause the RTE to unlock the doorstrike.Press 1 to cause the RTE to unlock the doorstrike.Press 0 to prevent the RTE from unlocking the Press 0 to prevent the RTE from unlocking the doorstrike.doorstrike.


Programming

41

01 GP CONFIGNORM OPEN 0

Enter 1 digit for the general purpose zone (VistaKey Enter 1 digit for the general purpose zone (VistaKey Zone C) configuration. This zone is normally used for Zone C) configuration. This zone is normally used for a tamper when the VistaKey cabinet requires a tamper when the VistaKey cabinet requires supervision. Acceptable 1-digit entries are as follows:supervision. Acceptable 1-digit entries are as follows:

0 = normally open0 = normally open 1 = normally closed1 = normally closed2 = EOLR normally open2 = EOLR normally open 3 = EOLR normally closed3 = EOLR normally closed

Press [*] to accept entry.Press [*] to accept entry.


Programming

42

< Menu< Menu

01 PREALARM TRIGNOT ENABLED 0

The prealarm trigger prompt is used to define if the The prealarm trigger prompt is used to define if the prealarm trigger is to be enabled. If the prealarm prealarm trigger is to be enabled. If the prealarm trigger is enabled, the trigger will be activated when trigger is enabled, the trigger will be activated when the prealarm time begins.the prealarm time begins.

Press 1 to enable the prealarm trigger outputPress 1 to enable the prealarm trigger output

Press 0 to disable the prealarm trigger output Press 0 to disable the prealarm trigger output


Programming

43

< Menu< Menu

01 TRIG MODENOT USED

The mode of operation of the trigger can be set to The mode of operation of the trigger can be set to “discrete,” “one-shot,” or “repeating.”“discrete,” “one-shot,” or “repeating.”


Programming

0 = 0 = not usednot used

1 = discrete trigger will energized and remain on until commanded off. 1 = discrete trigger will energized and remain on until commanded off. (advances to access group)(advances to access group)

2 = 2 = one-shot trigger energizes once when commanded on, stays on for one-shot trigger energizes once when commanded on, stays on for the specified on time. (advances to Trig on time)the specified on time. (advances to Trig on time)

3 = 3 = repeating trigger output cycles on and off for the specified amount of repeating trigger output cycles on and off for the specified amount of on time (advances to Trig REPT CNT)on time (advances to Trig REPT CNT)

44

< Menu< Menu

01 TRIG RPT CNTContinuous

Enter 1 digit representing the number of repeated Enter 1 digit representing the number of repeated on/off cycles that are output by the trigger function. If on/off cycles that are output by the trigger function. If number is set to 0, the trigger repeats continuously number is set to 0, the trigger repeats continuously until it is commanded off. Acceptable 1-digit entries until it is commanded off. Acceptable 1-digit entries are as follows. Press [ * ] to accept the entry.are as follows. Press [ * ] to accept the entry.

0 = Continuous0 = Continuous 3 = 3 cycles 3 = 3 cycles 6 = 10 cycles6 = 10 cycles

1 = 1 cycle1 = 1 cycle 4 = 4 cycles4 = 4 cycles 7 = 25 cycles7 = 25 cycles

2 = 2 cycles2 = 2 cycles 5 = 5 cycles5 = 5 cycles


Programming

45

< Menu< Menu

01 TRIG OFF TIME1s 0

Enter 1 digit for the time, in seconds, that the trigger Enter 1 digit for the time, in seconds, that the trigger is to remain de-energized if its mode is set as is to remain de-energized if its mode is set as repeating. This is the time that makes up the “OFF” repeating. This is the time that makes up the “OFF” time of a repeating cycle. Acceptable 1-digit entries time of a repeating cycle. Acceptable 1-digit entries are as follows. are as follows. Press [ * ] to accept the entry.Press [ * ] to accept the entry.

0 = 1 sec.0 = 1 sec. 3 = 4 sec. 3 = 4 sec. 6 = 15 sec.6 = 15 sec.

1 = 2 sec.1 = 2 sec. 4 = 5 sec. 4 = 5 sec. 7 = 30 sec.7 = 30 sec.

2 = 3 sec.2 = 3 sec. 5 = 10 sec.5 = 10 sec.


Programming

46

< Menu< Menu

01 TRIG ON TIME1s 0

Enter 1 digit for the time, in seconds, that the trigger is Enter 1 digit for the time, in seconds, that the trigger is to remain energized if its mode is set as one-shot. If to remain energized if its mode is set as one-shot. If the mode is set as repeating, this is the time that the mode is set as repeating, this is the time that makes up the “ON” time of a repeating cycle. makes up the “ON” time of a repeating cycle. Acceptable 1-digit entries are as follows. Acceptable 1-digit entries are as follows. Press [ * ] to Press [ * ] to accept the entry.accept the entry.

0 = 1 sec.0 = 1 sec. 3 = 5 sec. 3 = 5 sec. 6 = 1 min.6 = 1 min.

1 = 2 sec.1 = 2 sec. 4 = 10 sec. 4 = 10 sec. 7 = 2 min.7 = 2 min.

2 = 3 sec.2 = 3 sec. 5 = 30 sec.5 = 30 sec.


Programming

47

< Menu< Menu

ACS GRP ? 1 2 3 4 5 6 7 8HIT 0-8 x x x x x x x x

Select the access groups that will be allowed entry or Select the access groups that will be allowed entry or egress through this access point when their egress through this access point when their respective access group is enabled via scheduling. respective access group is enabled via scheduling.

Press 0 to toggle all access groups on or off; or press Press 0 to toggle all access groups on or off; or press keys 1-8 to toggle the letter “x” under the access keys 1-8 to toggle the letter “x” under the access group numbers on or off.group numbers on or off.

Press [ * ] to accept the entry.Press [ * ] to accept the entry.


Programming

48

< Menu< Menu

RDR CONFIGWEIGAND 0

This prompt accepts 0 (Weigand) or 1 (Clock/Data). This prompt accepts 0 (Weigand) or 1 (Clock/Data). The ADEMCO reader is a Weigand configuration The ADEMCO reader is a Weigand configuration (format) reader.(format) reader.

Press 0 for a Weigand reader configuration.Press 0 for a Weigand reader configuration.



Programming

49

< Menu< Menu

01 RDR POSITIONEntry 0

Enter reader position as either ENTRY or EXIT. This is Enter reader position as either ENTRY or EXIT. This is important for EXIT, EVENT & ENTRY event/action important for EXIT, EVENT & ENTRY event/action selection during Access Group Programming and selection during Access Group Programming and determines how associated events are logged and determines how associated events are logged and reported (e.g., Access Grant, Egress Grant). reported (e.g., Access Grant, Egress Grant).

Press 0 or 1 to select if the reader is an entry reader (0) Press 0 or 1 to select if the reader is an entry reader (0) or an exit reader (1). Press [ * ] to accept the entry.or an exit reader (1). Press [ * ] to accept the entry.


Programming

The system will return the following prompt:The system will return the following prompt:

ENTER ACS PT#

50

< Menu< Menu

ACCESS GRP PGM1 = YES 0 = NO 1ACCESS GROUP01 – 08 00 = QUIT 01

< Sub Menu

Enter #93 Menu Mode Programming and press the Enter #93 Menu Mode Programming and press the [0] key until the following prompt is displayed. [0] key until the following prompt is displayed. Press 1 to select access point programming.Press 1 to select access point programming.

Note that when assigning cards Note that when assigning cards to a new access group, the to a new access group, the cards in the new access group cards in the new access group will not be functional until the will not be functional until the new access group is enabled new access group is enabled (via #77, time schedules, etc.).(via #77, time schedules, etc.).

Enter a number from 1 to 8 for the access group to Enter a number from 1 to 8 for the access group to be programmed or enter 00 to Quit Access Group be programmed or enter 00 to Quit Access Group Programming.Programming.


Programming

51

< Menu< Menu

01 EXEC PRIV ?NOT ENABLED 0

Press 1 (enable) or 0 (disable) to define whether the group has Press 1 (enable) or 0 (disable) to define whether the group has executive privileges. executive privileges.

Enabling Executive Privilege enables all cardholders in this Enabling Executive Privilege enables all cardholders in this group to access any access point & disarm the access point’s group to access any access point & disarm the access point’s partition (if armed) at any time regardless of whether the partition (if armed) at any time regardless of whether the cardholder’s access group is enabled via scheduling or cardholder’s access group is enabled via scheduling or whether his access group is enabled to enter or exit through whether his access group is enabled to enter or exit through any of the access points. A cardholder with executive any of the access points. A cardholder with executive privileges would only be prevented from access by an access privileges would only be prevented from access by an access point is if his card has expired via usage or date.point is if his card has expired via usage or date.


Programming

52

< Menu< Menu

01 TRACE ?NOT ENABLED 0

Press 1 (trace) or 0 (no trace) to define whether the Press 1 (trace) or 0 (no trace) to define whether the cardholders in the group are to be traced.cardholders in the group are to be traced.

Enabling the trace feature allows this access group to Enabling the trace feature allows this access group to be monitored by logging entry/exit grants and denials be monitored by logging entry/exit grants and denials in the alarm panel log and/or dialing out and sending in the alarm panel log and/or dialing out and sending a report to the central station.a report to the central station.



Programming

53

< Menu< Menu

01 Restr ? 1 2 3 4 5 6 7 8HIT 0-8

Press 0 to toggle Armed Restriction for all VISTA Press 0 to toggle Armed Restriction for all VISTA partitions on or off; or press keys 1-8 (VISTA-128FB) partitions on or off; or press keys 1-8 (VISTA-128FB) or 1-2 (VISTA-32FB) to toggle the letter “x” under the or 1-2 (VISTA-32FB) to toggle the letter “x” under the Armed Restriction partition numbers on or off. Armed Restriction partition numbers on or off.

NOTES:NOTES: When the Armed Restriction is enabled for a partition & the partition is When the Armed Restriction is enabled for a partition & the partition is armed, a cardholder will be denied access through access points in a partition armed, a cardholder will be denied access through access points in a partition when both of the following conditions exist. when both of the following conditions exist. Press [Press [] to accept the entry.] to accept the entry.

1. All access groups that the cardholder belongs to have an Armed Restriction 1. All access groups that the cardholder belongs to have an Armed Restriction for the partition and none have executive privilege.for the partition and none have executive privilege.

2. The cardholder’s VISTA User # does not have access permission for the 2. The cardholder’s VISTA User # does not have access permission for the partition.partition.


Programming

54

< Menu< Menu

01 Entry Event ?Never Invoke 00

01 Access Point(01-15) 01

Enter two digits from the following list for the access Enter two digits from the following list for the access point-related entry event that causes the entry action point-related entry event that causes the entry action desired.desired.

Enter 1 through 15 for the access point number Enter 1 through 15 for the access point number corresponding to the entry event defined above.corresponding to the entry event defined above.

Press [Press [] to accept the entry.] to accept the entry.


Programming

55

< Menu< Menu

01 Entry Action ?None 00

01 Exit Event ?Never Invoke 00

Enter two digits defining the entry action desired.Enter two digits defining the entry action desired.

Enter 00 through 10 for the access point-related exit Enter 00 through 10 for the access point-related exit event desired. Acceptable entries and their event desired. Acceptable entries and their meanings are as follows:meanings are as follows:


Programming

56

< Menu< Menu

01 Access Point(01 - 15 ) 01

01 Exit Action ?None 00

Enter 1 through 15 for the access point number Enter 1 through 15 for the access point number corresponding to the exit event defined above. corresponding to the exit event defined above. Press [ * ] to accept the entry.Press [ * ] to accept the entry.

Enter two digits defining the exit action desired.Enter two digits defining the exit action desired.


Programming

57

Setting Up Access Groups


58

< Menu< Menu

When an access group is entered into the system for When an access group is entered into the system for the first time, the group must be enabled. The access the first time, the group must be enabled. The access group can be enabled either by time-driven events or by group can be enabled either by time-driven events or by the #77 command. If you are using the (#77) method to the #77 command. If you are using the (#77) method to enable the access group, proceed as follows:enable the access group, proceed as follows:

• enter installer code #77enter installer code #77• enter action number 77 (to enable access groups)enter action number 77 (to enable access groups)• enter the access group numberenter the access group number• quitquit



59

Adding, Editing & Deleting

Cards

Adding, Editing & Deleting

Cards

60

< Menu< Menu

Access Point 00

Access Point 01

< Sub Menu

To begin Card Function Programming, enter: User To begin Card Function Programming, enter: User Code + #79. The following prompt appears:Code + #79. The following prompt appears:

Adding/Editing & Deleting Cards


Enter the number (1-15) of the access point (door) Enter the number (1-15) of the access point (door) where you want to manipulate card data. Press [ * ] where you want to manipulate card data. Press [ * ] to accept entry.to accept entry.

61

< Menu< Menu

Add Card ?1 = YES 0 = NO

Adding CardsAdding Cards

Press 1 to Enroll a card or Edit a card by using a card Press 1 to Enroll a card or Edit a card by using a card swipe. Press 0 to advance to the Edit Card Function.swipe. Press 0 to advance to the Edit Card Function.



62

SWIPE CARDxxx-xx-xxxxxxx

When you press 1, the following prompt is displayed:When you press 1, the following prompt is displayed:

Swipe card or manually enter the (12-digit) card code Swipe card or manually enter the (12-digit) card code to be enrolled or edited. If you swipe a card, the keypad to be enrolled or edited. If you swipe a card, the keypad displays a 3-digit VISTA card ID number preceding displays a 3-digit VISTA card ID number preceding “SWIPE CARD” on the top line of the display and the “SWIPE CARD” on the top line of the display and the 12 digits of information contained on the card in the 12 digits of information contained on the card in the second line of the display.second line of the display.



63

< Menu< Menu

001 Exec Priv ?Not Enabled 0

Enabling executive privilege allows the cardholder Enabling executive privilege allows the cardholder to access any access point and disarm its partition to access any access point and disarm its partition (if armed) at any time. This occurs regardless of (if armed) at any time. This occurs regardless of whether the cardholder’s access group is enabled whether the cardholder’s access group is enabled via scheduling or whether his access group is via scheduling or whether his access group is enabled to enter or exit through any access point.enabled to enter or exit through any access point.

Press 1 to provide the cardholder with executive Press 1 to provide the cardholder with executive privileges or 0 for no executive privileges. privileges or 0 for no executive privileges.




64

< Menu< Menu

001 Trace ?NOT ENABLED 0

The Trace feature allows the cardholder to be The Trace feature allows the cardholder to be monitored by logging his entry/exit grants and monitored by logging his entry/exit grants and denials in the log and (if programmed) dialing out and denials in the log and (if programmed) dialing out and sending a report to central station.sending a report to central station.

Press 1 to trace the cardholder, or 0 for no trace. Press 1 to trace the cardholder, or 0 for no trace. Press [ * ] to accept the entry.Press [ * ] to accept the entry.



65

< Menu< Menu

ACS GRP? 1 2 3 4 5 6 7 8HIT 0-8 x x

Each cardholder must belong to at least one access Each cardholder must belong to at least one access group. The access group provides the cardholder with group. The access group provides the cardholder with certain privileges afforded to all cardholders that belong certain privileges afforded to all cardholders that belong to that access group. If a cardholder belongs to more to that access group. If a cardholder belongs to more than one access group, he is afforded all the privileges than one access group, he is afforded all the privileges of all the access groups he belongs to. The access of all the access groups he belongs to. The access groups also determine which access point(s) the groups also determine which access point(s) the cardholder has access to, and at what times, according cardholder has access to, and at what times, according to the schedule his access group is enabled.to the schedule his access group is enabled.



66

Press 0 to toggle all groups on or off; or press keys Press 0 to toggle all groups on or off; or press keys 1-8 to toggle the letter “x” under the group numbers 1-8 to toggle the letter “x” under the group numbers on or off. on or off.


ACS GRP? 1 2 3 4 5 6 7 8HIT 0-8 x x



67

< Menu< Menu

001 Expire use?UNLIMITED USE 00

Expire useExpire use defines whether the cardholder access defines whether the cardholder access privileges are to expire with usage. Enter 00 for privileges are to expire with usage. Enter 00 for unlimited use. Otherwise, enter a number between unlimited use. Otherwise, enter a number between 01 and 14. Entering a number between 01 and 14 01 and 14. Entering a number between 01 and 14 allows that many entry access grants for this allows that many entry access grants for this cardholder. cardholder.




Note: Egress grants have no Note: Egress grants have no effect on the usage count. effect on the usage count. Entering 15 automatically Entering 15 automatically expires the card and expires the card and prevents entry grants even if prevents entry grants even if the cardholder has executive the cardholder has executive privilege. Expiring a card privilege. Expiring a card does NOT delete it from the does NOT delete it from the card database, and the card card database, and the card retains its card ID#.retains its card ID#.

68

< Menu< Menu

001 Expire MonthNO EXPIRATION 00

00 = Normal (no expiration)

08 = August

01 = January

09 = September

02 = February

10 = October

03 = March

11 = November

04 = April

12 = December

05 = May

13 = End of Day

06 = June

14 = End of Week

07 = July

15 = End of Month

Enter two digits from 00 to 15. The digits entered Enter two digits from 00 to 15. The digits entered provide the following expiration functions:provide the following expiration functions:

NOTE: Cards expire at midnight for month, end of day, end of week (Sunday), or end of month selections. Press [*] to accept the entry.



69

< Menu< Menu

001 Day of Month 00

If you entered 01-12, the system displays the “Day If you entered 01-12, the system displays the “Day of Month” prompt. of Month” prompt. Enter the day of the month. Enter the day of the month. Note that the card expires at midnight of the day Note that the card expires at midnight of the day that you enter.that you enter.




70

001 Vista User# 000

If you entered 00 or 13-15 the system advances to the If you entered 00 or 13-15 the system advances to the following prompt:following prompt:

The VISTA User number may be used to allow a The VISTA User number may be used to allow a cardholder access to an armed partition even if the cardholder access to an armed partition even if the cardholder’s access group is restricted for that partition. cardholder’s access group is restricted for that partition. Additionally, the VISTA User number can be used to Additionally, the VISTA User number can be used to allow this cardholder to use wireless keyfobs to grant allow this cardholder to use wireless keyfobs to grant access and egress through his allotted access points.access and egress through his allotted access points.



71

< Menu< Menu

001 ACS Event ?Never Invoke 00001 Access Point?(01-15) 01

Enter two digits from the list below for the access Enter two digits from the list below for the access point-related event desired. Acceptable entries have point-related event desired. Acceptable entries have the following meanings. Press [*] to accept the entry.the following meanings. Press [*] to accept the entry.00 = never invoke 06 = egress grant 02= access request 07 = any grant03 = egress request 08 = access denied04 = any request 09 = egress denied05 = access grant 10 = any denial

Enter 1-15 for access point number corresponding to Enter 1-15 for access point number corresponding to event defined above. Press [*] to accept the entry.event defined above. Press [*] to accept the entry.



72

< Menu< Menu

001 ACTION?None 00001 Block Entry?1=YES 0=NO 0

Block enrollment (entry) enrolls numerous cards with Block enrollment (entry) enrolls numerous cards with the same previously entered data. the same previously entered data.

If the card data to be entered is significantly different If the card data to be entered is significantly different from one card to another, then answer “NO” and from one card to another, then answer “NO” and enter each card’s data individually. enter each card’s data individually.

Enter “YES” to duplicate card data for every card Enter “YES” to duplicate card data for every card swiped.swiped.



73

< Menu< Menu

Quit?1=YES 0=NO 0

If you press 1, the system advances to the “Quit If you press 1, the system advances to the “Quit Card Mode?” prompt. If you press 0, the system Card Mode?” prompt. If you press 0, the system returns to the “SWIPE CARD” prompt.returns to the “SWIPE CARD” prompt.

At the “Quick Card mode” prompt…continue to At the “Quick Card mode” prompt…continue to press 0 until the keypad displays the desired prompt press 0 until the keypad displays the desired prompt and then press 1.and then press 1.



74

< Menu< Menu

After entering the card function programming, enter 0 After entering the card function programming, enter 0 to toggle through the various card options.to toggle through the various card options.

At the AutoDelete prompt, enter 1.At the AutoDelete prompt, enter 1.



Editing CardsEditing Cards

Edit Card1=YES 0=NO 1Card #1 - 250 0=Quit 001

If you enter 0 again, the system advances to the “Block If you enter 0 again, the system advances to the “Block Delete” prompt.Delete” prompt.

This mode deletes single cards from the database.This mode deletes single cards from the database.

75

< Menu< Menu



After entering the Card number, enter {*} to advance to After entering the Card number, enter {*} to advance to the Exec privilege prompt.the Exec privilege prompt.

The display prompts are identical to those just covered The display prompts are identical to those just covered under “Adding Cards.”under “Adding Cards.”

002 EXEC PRIV?NOT ENABLED 0

76

After entering the Card function programming, enter 0 After entering the Card function programming, enter 0 to toggle through the various card options.to toggle through the various card options.

At the AutoDelete prompt, enter 1.At the AutoDelete prompt, enter 1.

If you enter 0 again, the system advanced to the “Block If you enter 0 again, the system advanced to the “Block Delete” prompt. This mode allows you to delete single Delete” prompt. This mode allows you to delete single cards from the database.cards from the database.

Auto DeleteAuto Delete

AUTO DELETE?1=YES 0= NO 1



77

< Menu< Menu

Swipe Cardxxx-xx-xxxxxxx

Swipe card or enter card number to be deleted. The Swipe card or enter card number to be deleted. The card number and VISTA card ID number to be deleted card number and VISTA card ID number to be deleted is displayed on the keypad. Note that if the card is displayed on the keypad. Note that if the card swiped is not found in the system database, the card swiped is not found in the system database, the card number displayed and VISTA card ID number are number displayed and VISTA card ID number are shown as zeros. Press [*] to accept the entry.shown as zeros. Press [*] to accept the entry.



78

< Menu< Menu

Card not Found* to continue

If the card is not found in the system, the following If the card is not found in the system, the following “Card Not Found” prompt is displayed. “Card Not Found” prompt is displayed.

Press [*] to continue. The system advances to the Press [*] to continue. The system advances to the “Quit?” prompt.“Quit?” prompt.



79

Are You Sure?1=YES 0=NO 1

Quit?1=YES 0=NO 1

< Menu< Menu

If you press 1, the system marks the card as deleted in If you press 1, the system marks the card as deleted in the card database. If you press 0, the system advances the card database. If you press 0, the system advances to the “Quit?” prompt. Press [*] to accept the entry.to the “Quit?” prompt. Press [*] to accept the entry.

If you press 1, the system advances to the “Quit Card If you press 1, the system advances to the “Quit Card Mode?” prompt. If you press 0, the system returns to Mode?” prompt. If you press 0, the system returns to the “Swipe Card” prompt. Press [*] to accept the entry.the “Swipe Card” prompt. Press [*] to accept the entry.



80

< Menu< Menu

Block Delete?1=YES 0=NO 1

After entering the Card Function Programming, enter 0 After entering the Card Function Programming, enter 0 to toggle though the various card options. At the to toggle though the various card options. At the BlockDelete prompt, enter 1. BlockDelete prompt, enter 1.

If you enter 0 again, the system advance to the “Manual If you enter 0 again, the system advance to the “Manual Delete” prompt. This mode allow you to delete Multiple Delete” prompt. This mode allow you to delete Multiple cards from the database.cards from the database.



Block DeleteBlock Delete

81

< Menu< Menu

Delete from Card1-250 0=Quit 001To Card1-250 0=Quit 025

Enter the 3-digit number corresponding to the Enter the 3-digit number corresponding to the beginning (lowest) card number for the deletion. If you beginning (lowest) card number for the deletion. If you enter 000, the system advances to the “Quit Card enter 000, the system advances to the “Quit Card Mode?” prompt. Press [*] to accept the entry.Mode?” prompt. Press [*] to accept the entry.



Enter the 3-digit number corresponding to the ending Enter the 3-digit number corresponding to the ending (highest) card number for the deletion.(highest) card number for the deletion.

82

< Menu< Menu

Are you sure?1=Yes 0=No 1



83

< Menu< Menu

Block Delete?1=YES 0=NO 1

Manual DeleteManual Delete

This mode allow you to delete single cards from the This mode allow you to delete single cards from the database.database.



Documents

2 If you can install a Vista panel... you can install VistaKey!